* [PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board
@ 2021-08-27 20:27 ` Vladimir Oltean
0 siblings, 0 replies; 12+ messages in thread
From: Vladimir Oltean @ 2021-08-27 20:27 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-arm-kernel, netdev
Cc: Rob Herring, Shawn Guo, Li Yang, Wasim Khan, Vabhav Sharma,
Kuldeep Singh, Florin Chiculita, Biwen Li, Heinz Wrobel,
Yangbo Lu
From: Wasim Khan <wasim.khan@nxp.com>
The NXP BlueBox3 is a prototyping board for high-performance autonomous
driving systems. It contains two Linux systems, on running on the
LX2160A and the other on the S32G2 SoC. This patch adds the device tree
support for the LX2160A SoC.
In terms of networking from the LX2160A's perspective, there are:
- 4 RJ45 10G ports using Aquantia copper PHYs which are attached
directly to DPAA2 ports on the LX2160A
- 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
the LX2160A (each switch has a host port towards a dpmac), the third
switch is managed by the S32G2. All 3 switches are interconnected
through on-board SERDES lanes. The cascade ports between the 2
switches managed by LX2160A form a DSA link, the cascade ports between
the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
device).
- 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
to NXP SJA1110 switches
- 12 automotive 100base-T1 single-pair Ethernet ports routed from the
SJA1110 internal PHY ports (TJA1103)
- One SGMII SERDES lane towards an internal connector, attached to one
of the SJA1110 switch ports
On board rev A, the AR8035 RGMII PHY addresses were different than on
rev B and later. This patch introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Co-developed-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 2 +
.../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 +
.../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++
3 files changed, 694 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index db9e36ebe932..ecf74464705f 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
new file mode 100644
index 000000000000..15d273c93154
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a-bluebox3.dts"
+
+/ {
+ compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
+};
+
+/* The RGMII PHYs have a different MDIO address */
+&emdio1 {
+ /delete-node/ ethernet-phy@5;
+
+ sw1_mii3_phy: ethernet-phy@1 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x1>;
+ interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ /delete-node/ ethernet-phy@6;
+
+ sw2_mii3_phy: ethernet-phy@2 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x2>;
+ interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
new file mode 100644
index 000000000000..be7d01630a6f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
@@ -0,0 +1,658 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160ABLUEBOX3";
+ compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
+
+ aliases {
+ crypto = &crypto;
+ serial0 = &uart0;
+ mmc0 = &esdhc0;
+ mmc1 = &esdhc1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-sb3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MC34717-3.3VSB";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&can0 {
+ status = "okay";
+
+ can-transceiver {
+ max-bitrate = <5000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+
+ can-transceiver {
+ max-bitrate = <5000000>;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&dpmac5 {
+ phy-handle = <&aqr113c_phy1>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac6 {
+ phy-handle = <&aqr113c_phy2>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac9 {
+ phy-handle = <&aqr113c_phy3>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac10 {
+ phy-handle = <&aqr113c_phy4>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac17 {
+ phy-mode = "rgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&dpmac18 {
+ phy-mode = "rgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&emdio1 {
+ status = "okay";
+
+ aqr113c_phy2: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x0>;
+ /* IRQ_10G_PHY2 */
+ interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ aqr113c_phy1: ethernet-phy@8 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x8>;
+ /* IRQ_10G_PHY1 */
+ interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ sw1_mii3_phy: ethernet-phy@5 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x5>;
+ interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ sw2_mii3_phy: ethernet-phy@6 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x6>;
+ interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&emdio2 {
+ status = "okay";
+
+ aqr113c_phy4: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x0>;
+ /* IRQ_10G_PHY4 */
+ interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ aqr113c_phy3: ethernet-phy@8 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x8>;
+ /* IRQ_10G_PHY3 */
+ interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&esdhc0 {
+ sd-uhs-sdr104;
+ sd-uhs-sdr50;
+ sd-uhs-sdr25;
+ sd-uhs-sdr12;
+ status = "okay";
+};
+
+&esdhc1 {
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&fspi {
+ status = "okay";
+
+ mt35xu512aba0: flash@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <8>;
+ spi-tx-bus-width = <8>;
+ };
+
+ mt35xu512aba1: flash@1 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <1>;
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <8>;
+ spi-tx-bus-width = <8>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temp2: temperature-sensor@48 {
+ compatible = "nxp,sa56004";
+ reg = <0x48>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ temp1: temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9547";
+ reg = <0x75>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ spi_bridge: spi@28 {
+ compatible = "nxp,sc18is602b";
+ reg = <0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9846";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ /* The I2C multiplexer and temperature sensors are on
+ * the T6 riser card.
+ */
+ i2c-mux@70 {
+ compatible = "nxp,pca9548";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6>;
+
+ q12: temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ i2c@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+
+ q11: temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ q13: temperature-sensor@48 {
+ compatible = "nxp,sa56004";
+ reg = <0x48>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ q14: temperature-sensor@4a {
+ compatible = "nxp,sa56004";
+ reg = <0x4a>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&pcs_mdio5 {
+ status = "okay";
+};
+
+&pcs_mdio6 {
+ status = "okay";
+};
+
+&pcs_mdio9 {
+ status = "okay";
+};
+
+&pcs_mdio10 {
+ status = "okay";
+};
+
+&spi_bridge {
+ sw1: ethernet-switch@0 {
+ compatible = "nxp,sja1110a";
+ reg = <0>;
+ spi-max-frequency = <4000000>;
+ spi-cpol;
+ dsa,member = <0 0>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microcontroller port */
+ port@0 {
+ reg = <0>;
+ status = "disabled";
+ };
+
+ /* SW1_P1 */
+ port@1 {
+ reg = <1>;
+ label = "con_2x20";
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ ethernet = <&dpmac17>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "1ge_p1";
+ phy-mode = "rgmii-id";
+ phy-handle = <&sw1_mii3_phy>;
+ };
+
+ sw1p4: port@4 {
+ reg = <4>;
+ link = <&sw2p1>;
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "trx1";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port5_base_t1_phy>;
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "trx2";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port6_base_t1_phy>;
+ };
+
+ port@7 {
+ reg = <7>;
+ label = "trx3";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port7_base_t1_phy>;
+ };
+
+ port@8 {
+ reg = <8>;
+ label = "trx4";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port8_base_t1_phy>;
+ };
+
+ port@9 {
+ reg = <9>;
+ label = "trx5";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port9_base_t1_phy>;
+ };
+
+ port@a {
+ reg = <10>;
+ label = "trx6";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port10_base_t1_phy>;
+ };
+ };
+
+ mdios {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@0 {
+ compatible = "nxp,sja1110-base-t1-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sw1_port5_base_t1_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x1>;
+ };
+
+ sw1_port6_base_t1_phy: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x2>;
+ };
+
+ sw1_port7_base_t1_phy: ethernet-phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x3>;
+ };
+
+ sw1_port8_base_t1_phy: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x4>;
+ };
+
+ sw1_port9_base_t1_phy: ethernet-phy@5 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x5>;
+ };
+
+ sw1_port10_base_t1_phy: ethernet-phy@6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x6>;
+ };
+ };
+ };
+ };
+
+ sw2: ethernet-switch@2 {
+ compatible = "nxp,sja1110a";
+ reg = <2>;
+ spi-max-frequency = <4000000>;
+ spi-cpol;
+ dsa,member = <0 1>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microcontroller port */
+ port@0 {
+ reg = <0>;
+ status = "disabled";
+ };
+
+ sw2p1: port@1 {
+ reg = <1>;
+ link = <&sw1p4>;
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ ethernet = <&dpmac18>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "1ge_p2";
+ phy-mode = "rgmii-id";
+ phy-handle = <&sw2_mii3_phy>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "to_sw3";
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "trx7";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port5_base_t1_phy>;
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "trx8";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port6_base_t1_phy>;
+ };
+
+ port@7 {
+ reg = <7>;
+ label = "trx9";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port7_base_t1_phy>;
+ };
+
+ port@8 {
+ reg = <8>;
+ label = "trx10";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port8_base_t1_phy>;
+ };
+
+ port@9 {
+ reg = <9>;
+ label = "trx11";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port9_base_t1_phy>;
+ };
+
+ port@a {
+ reg = <10>;
+ label = "trx12";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port10_base_t1_phy>;
+ };
+ };
+
+ mdios {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@0 {
+ compatible = "nxp,sja1110-base-t1-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sw2_port5_base_t1_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x1>;
+ };
+
+ sw2_port6_base_t1_phy: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x2>;
+ };
+
+ sw2_port7_base_t1_phy: ethernet-phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x3>;
+ };
+
+ sw2_port8_base_t1_phy: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x4>;
+ };
+
+ sw2_port9_base_t1_phy: ethernet-phy@5 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x5>;
+ };
+
+ sw2_port10_base_t1_phy: ethernet-phy@6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x6>;
+ };
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board
2021-08-27 20:27 ` Vladimir Oltean
@ 2021-08-28 1:38 ` Li Yang
-1 siblings, 0 replies; 12+ messages in thread
From: Li Yang @ 2021-08-28 1:38 UTC (permalink / raw)
To: Vladimir Oltean
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, lkml,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE, Netdev,
Rob Herring, Shawn Guo, Wasim Khan, Vabhav Sharma, Kuldeep Singh,
Florin Chiculita, Biwen Li, Heinz Wrobel, Yangbo Lu
On Fri, Aug 27, 2021 at 3:28 PM Vladimir Oltean <vladimir.oltean@nxp.com> wrote:
>
> From: Wasim Khan <wasim.khan@nxp.com>
>
> The NXP BlueBox3 is a prototyping board for high-performance autonomous
> driving systems. It contains two Linux systems, on running on the
> LX2160A and the other on the S32G2 SoC. This patch adds the device tree
> support for the LX2160A SoC.
>
> In terms of networking from the LX2160A's perspective, there are:
>
> - 4 RJ45 10G ports using Aquantia copper PHYs which are attached
> directly to DPAA2 ports on the LX2160A
>
> - 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
> the LX2160A (each switch has a host port towards a dpmac), the third
> switch is managed by the S32G2. All 3 switches are interconnected
> through on-board SERDES lanes. The cascade ports between the 2
> switches managed by LX2160A form a DSA link, the cascade ports between
> the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
> device).
>
> - 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
> to NXP SJA1110 switches
>
> - 12 automotive 100base-T1 single-pair Ethernet ports routed from the
> SJA1110 internal PHY ports (TJA1103)
>
> - One SGMII SERDES lane towards an internal connector, attached to one
> of the SJA1110 switch ports
>
> On board rev A, the AR8035 RGMII PHY addresses were different than on
> rev B and later. This patch introduces a separate device tree for rev A.
> The main device tree is supposed to cover rev B and later.
>
> Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
> Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Co-developed-by: Biwen Li <biwen.li@nxp.com>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
> Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 2 +
> .../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 +
> .../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++
> 3 files changed, 694 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..ecf74464705f 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> new file mode 100644
> index 000000000000..15d273c93154
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a-bluebox3.dts"
> +
> +/ {
> + compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
> +};
> +
> +/* The RGMII PHYs have a different MDIO address */
> +&emdio1 {
> + /delete-node/ ethernet-phy@5;
> +
> + sw1_mii3_phy: ethernet-phy@1 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x1>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + /delete-node/ ethernet-phy@6;
> +
> + sw2_mii3_phy: ethernet-phy@2 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x2>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> new file mode 100644
> index 000000000000..be7d01630a6f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> @@ -0,0 +1,658 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> + model = "NXP Layerscape LX2160ABLUEBOX3";
> + compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
> +
> + aliases {
> + crypto = &crypto;
> + serial0 = &uart0;
> + mmc0 = &esdhc0;
> + mmc1 = &esdhc1;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + sb_3v3: regulator-sb3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "MC34717-3.3VSB";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +};
> +
> +&can0 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&can1 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> +&dpmac5 {
> + phy-handle = <&aqr113c_phy1>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac6 {
> + phy-handle = <&aqr113c_phy2>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac9 {
> + phy-handle = <&aqr113c_phy3>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac10 {
> + phy-handle = <&aqr113c_phy4>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac17 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&dpmac18 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&emdio1 {
> + status = "okay";
> +
> + aqr113c_phy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY2 */
> + interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy1: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY1 */
> + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw1_mii3_phy: ethernet-phy@5 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x5>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw2_mii3_phy: ethernet-phy@6 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x6>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&emdio2 {
> + status = "okay";
> +
> + aqr113c_phy4: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY4 */
> + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy3: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY3 */
> + interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&esdhc0 {
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&fspi {
> + status = "okay";
> +
> + mt35xu512aba0: flash@0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +
> + mt35xu512aba1: flash@1 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9547";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> +
> + power-monitor@40 {
> + compatible = "ti,ina220";
> + reg = <0x40>;
> + shunt-resistor = <500>;
> + };
> + };
> +
> + i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> +
> + temp2: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + temp1: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4>;
> +
> + rtc@51 {
> + compatible = "nxp,pcf2129";
> + reg = <0x51>;
> + interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + i2c-mux@75 {
> + compatible = "nxp,pca9547";
> + reg = <0x75>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0>;
> +
> + spi_bridge: spi@28 {
> + compatible = "nxp,sc18is602b";
> + reg = <0x28>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9846";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x1>;
> +
> + /* The I2C multiplexer and temperature sensors are on
> + * the T6 riser card.
> + */
> + i2c-mux@70 {
> + compatible = "nxp,pca9548";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x6>;
> +
> + q12: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + q11: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q13: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q14: temperature-sensor@4a {
> + compatible = "nxp,sa56004";
> + reg = <0x4a>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&pcs_mdio5 {
> + status = "okay";
> +};
> +
> +&pcs_mdio6 {
> + status = "okay";
> +};
> +
> +&pcs_mdio9 {
> + status = "okay";
> +};
> +
> +&pcs_mdio10 {
> + status = "okay";
> +};
> +
> +&spi_bridge {
> + sw1: ethernet-switch@0 {
> + compatible = "nxp,sja1110a";
> + reg = <0>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 0>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + /* SW1_P1 */
> + port@1 {
> + reg = <1>;
> + label = "con_2x20";
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac17>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p1";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw1_mii3_phy>;
> + };
> +
> + sw1p4: port@4 {
> + reg = <4>;
> + link = <&sw2p1>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx1";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx2";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx3";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx4";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx5";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx6";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw1_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw1_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw1_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw1_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw1_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw1_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +
> + sw2: ethernet-switch@2 {
> + compatible = "nxp,sja1110a";
> + reg = <2>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 1>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + sw2p1: port@1 {
> + reg = <1>;
> + link = <&sw1p4>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac18>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p2";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw2_mii3_phy>;
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "to_sw3";
> + phy-mode = "2500base-x";
> +
> + fixed-link {
> + speed = <2500>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx7";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx8";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx9";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx10";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx11";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx12";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw2_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw2_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw2_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw2_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw2_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw2_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board
@ 2021-08-28 1:38 ` Li Yang
0 siblings, 0 replies; 12+ messages in thread
From: Li Yang @ 2021-08-28 1:38 UTC (permalink / raw)
To: Vladimir Oltean
Cc: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, lkml,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE, Netdev,
Rob Herring, Shawn Guo, Wasim Khan, Vabhav Sharma, Kuldeep Singh,
Florin Chiculita, Biwen Li, Heinz Wrobel, Yangbo Lu
On Fri, Aug 27, 2021 at 3:28 PM Vladimir Oltean <vladimir.oltean@nxp.com> wrote:
>
> From: Wasim Khan <wasim.khan@nxp.com>
>
> The NXP BlueBox3 is a prototyping board for high-performance autonomous
> driving systems. It contains two Linux systems, on running on the
> LX2160A and the other on the S32G2 SoC. This patch adds the device tree
> support for the LX2160A SoC.
>
> In terms of networking from the LX2160A's perspective, there are:
>
> - 4 RJ45 10G ports using Aquantia copper PHYs which are attached
> directly to DPAA2 ports on the LX2160A
>
> - 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
> the LX2160A (each switch has a host port towards a dpmac), the third
> switch is managed by the S32G2. All 3 switches are interconnected
> through on-board SERDES lanes. The cascade ports between the 2
> switches managed by LX2160A form a DSA link, the cascade ports between
> the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
> device).
>
> - 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
> to NXP SJA1110 switches
>
> - 12 automotive 100base-T1 single-pair Ethernet ports routed from the
> SJA1110 internal PHY ports (TJA1103)
>
> - One SGMII SERDES lane towards an internal connector, attached to one
> of the SJA1110 switch ports
>
> On board rev A, the AR8035 RGMII PHY addresses were different than on
> rev B and later. This patch introduces a separate device tree for rev A.
> The main device tree is supposed to cover rev B and later.
>
> Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
> Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Co-developed-by: Biwen Li <biwen.li@nxp.com>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
> Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 2 +
> .../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 +
> .../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++
> 3 files changed, 694 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..ecf74464705f 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> new file mode 100644
> index 000000000000..15d273c93154
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a-bluebox3.dts"
> +
> +/ {
> + compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
> +};
> +
> +/* The RGMII PHYs have a different MDIO address */
> +&emdio1 {
> + /delete-node/ ethernet-phy@5;
> +
> + sw1_mii3_phy: ethernet-phy@1 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x1>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + /delete-node/ ethernet-phy@6;
> +
> + sw2_mii3_phy: ethernet-phy@2 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x2>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> new file mode 100644
> index 000000000000..be7d01630a6f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> @@ -0,0 +1,658 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> + model = "NXP Layerscape LX2160ABLUEBOX3";
> + compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
> +
> + aliases {
> + crypto = &crypto;
> + serial0 = &uart0;
> + mmc0 = &esdhc0;
> + mmc1 = &esdhc1;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + sb_3v3: regulator-sb3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "MC34717-3.3VSB";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +};
> +
> +&can0 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&can1 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> +&dpmac5 {
> + phy-handle = <&aqr113c_phy1>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac6 {
> + phy-handle = <&aqr113c_phy2>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac9 {
> + phy-handle = <&aqr113c_phy3>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac10 {
> + phy-handle = <&aqr113c_phy4>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac17 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&dpmac18 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&emdio1 {
> + status = "okay";
> +
> + aqr113c_phy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY2 */
> + interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy1: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY1 */
> + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw1_mii3_phy: ethernet-phy@5 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x5>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw2_mii3_phy: ethernet-phy@6 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x6>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&emdio2 {
> + status = "okay";
> +
> + aqr113c_phy4: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY4 */
> + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy3: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY3 */
> + interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&esdhc0 {
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&fspi {
> + status = "okay";
> +
> + mt35xu512aba0: flash@0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +
> + mt35xu512aba1: flash@1 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9547";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> +
> + power-monitor@40 {
> + compatible = "ti,ina220";
> + reg = <0x40>;
> + shunt-resistor = <500>;
> + };
> + };
> +
> + i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> +
> + temp2: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + temp1: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4>;
> +
> + rtc@51 {
> + compatible = "nxp,pcf2129";
> + reg = <0x51>;
> + interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + i2c-mux@75 {
> + compatible = "nxp,pca9547";
> + reg = <0x75>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0>;
> +
> + spi_bridge: spi@28 {
> + compatible = "nxp,sc18is602b";
> + reg = <0x28>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9846";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x1>;
> +
> + /* The I2C multiplexer and temperature sensors are on
> + * the T6 riser card.
> + */
> + i2c-mux@70 {
> + compatible = "nxp,pca9548";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x6>;
> +
> + q12: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + q11: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q13: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q14: temperature-sensor@4a {
> + compatible = "nxp,sa56004";
> + reg = <0x4a>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&pcs_mdio5 {
> + status = "okay";
> +};
> +
> +&pcs_mdio6 {
> + status = "okay";
> +};
> +
> +&pcs_mdio9 {
> + status = "okay";
> +};
> +
> +&pcs_mdio10 {
> + status = "okay";
> +};
> +
> +&spi_bridge {
> + sw1: ethernet-switch@0 {
> + compatible = "nxp,sja1110a";
> + reg = <0>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 0>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + /* SW1_P1 */
> + port@1 {
> + reg = <1>;
> + label = "con_2x20";
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac17>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p1";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw1_mii3_phy>;
> + };
> +
> + sw1p4: port@4 {
> + reg = <4>;
> + link = <&sw2p1>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx1";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx2";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx3";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx4";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx5";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx6";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw1_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw1_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw1_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw1_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw1_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw1_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +
> + sw2: ethernet-switch@2 {
> + compatible = "nxp,sja1110a";
> + reg = <2>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 1>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + sw2p1: port@1 {
> + reg = <1>;
> + link = <&sw1p4>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac18>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p2";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw2_mii3_phy>;
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "to_sw3";
> + phy-mode = "2500base-x";
> +
> + fixed-link {
> + speed = <2500>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx7";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx8";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx9";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx10";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx11";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx12";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw2_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw2_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw2_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw2_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw2_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw2_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board
2021-08-27 20:27 ` Vladimir Oltean
@ 2021-10-04 3:43 ` Shawn Guo
-1 siblings, 0 replies; 12+ messages in thread
From: Shawn Guo @ 2021-10-04 3:43 UTC (permalink / raw)
To: Vladimir Oltean
Cc: devicetree, linux-kernel, linux-arm-kernel, netdev, Rob Herring,
Li Yang, Wasim Khan, Vabhav Sharma, Kuldeep Singh,
Florin Chiculita, Biwen Li, Heinz Wrobel, Yangbo Lu
On Fri, Aug 27, 2021 at 11:27:22PM +0300, Vladimir Oltean wrote:
> From: Wasim Khan <wasim.khan@nxp.com>
>
> The NXP BlueBox3 is a prototyping board for high-performance autonomous
> driving systems. It contains two Linux systems, on running on the
s/on running/running
> LX2160A and the other on the S32G2 SoC. This patch adds the device tree
> support for the LX2160A SoC.
>
> In terms of networking from the LX2160A's perspective, there are:
>
> - 4 RJ45 10G ports using Aquantia copper PHYs which are attached
> directly to DPAA2 ports on the LX2160A
>
> - 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
> the LX2160A (each switch has a host port towards a dpmac), the third
> switch is managed by the S32G2. All 3 switches are interconnected
> through on-board SERDES lanes. The cascade ports between the 2
> switches managed by LX2160A form a DSA link, the cascade ports between
> the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
> device).
>
> - 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
> to NXP SJA1110 switches
>
> - 12 automotive 100base-T1 single-pair Ethernet ports routed from the
> SJA1110 internal PHY ports (TJA1103)
>
> - One SGMII SERDES lane towards an internal connector, attached to one
> of the SJA1110 switch ports
>
> On board rev A, the AR8035 RGMII PHY addresses were different than on
> rev B and later. This patch introduces a separate device tree for rev A.
> The main device tree is supposed to cover rev B and later.
>
> Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
> Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Co-developed-by: Biwen Li <biwen.li@nxp.com>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
> Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 2 +
> .../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 +
> .../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++
> 3 files changed, 694 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..ecf74464705f 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> new file mode 100644
> index 000000000000..15d273c93154
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a-bluebox3.dts"
> +
> +/ {
> + compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
> +};
> +
> +/* The RGMII PHYs have a different MDIO address */
> +&emdio1 {
> + /delete-node/ ethernet-phy@5;
> +
> + sw1_mii3_phy: ethernet-phy@1 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x1>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + /delete-node/ ethernet-phy@6;
> +
> + sw2_mii3_phy: ethernet-phy@2 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x2>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> new file mode 100644
> index 000000000000..be7d01630a6f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> @@ -0,0 +1,658 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> + model = "NXP Layerscape LX2160ABLUEBOX3";
> + compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
> +
> + aliases {
> + crypto = &crypto;
> + serial0 = &uart0;
> + mmc0 = &esdhc0;
> + mmc1 = &esdhc1;
It's nice to have them sort alphabetically.
I fixed them up and applied the patch.
Shawn
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + sb_3v3: regulator-sb3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "MC34717-3.3VSB";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +};
> +
> +&can0 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&can1 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> +&dpmac5 {
> + phy-handle = <&aqr113c_phy1>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac6 {
> + phy-handle = <&aqr113c_phy2>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac9 {
> + phy-handle = <&aqr113c_phy3>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac10 {
> + phy-handle = <&aqr113c_phy4>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac17 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&dpmac18 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&emdio1 {
> + status = "okay";
> +
> + aqr113c_phy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY2 */
> + interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy1: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY1 */
> + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw1_mii3_phy: ethernet-phy@5 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x5>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw2_mii3_phy: ethernet-phy@6 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x6>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&emdio2 {
> + status = "okay";
> +
> + aqr113c_phy4: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY4 */
> + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy3: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY3 */
> + interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&esdhc0 {
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&fspi {
> + status = "okay";
> +
> + mt35xu512aba0: flash@0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +
> + mt35xu512aba1: flash@1 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9547";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> +
> + power-monitor@40 {
> + compatible = "ti,ina220";
> + reg = <0x40>;
> + shunt-resistor = <500>;
> + };
> + };
> +
> + i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> +
> + temp2: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + temp1: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4>;
> +
> + rtc@51 {
> + compatible = "nxp,pcf2129";
> + reg = <0x51>;
> + interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + i2c-mux@75 {
> + compatible = "nxp,pca9547";
> + reg = <0x75>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0>;
> +
> + spi_bridge: spi@28 {
> + compatible = "nxp,sc18is602b";
> + reg = <0x28>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9846";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x1>;
> +
> + /* The I2C multiplexer and temperature sensors are on
> + * the T6 riser card.
> + */
> + i2c-mux@70 {
> + compatible = "nxp,pca9548";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x6>;
> +
> + q12: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + q11: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q13: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q14: temperature-sensor@4a {
> + compatible = "nxp,sa56004";
> + reg = <0x4a>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&pcs_mdio5 {
> + status = "okay";
> +};
> +
> +&pcs_mdio6 {
> + status = "okay";
> +};
> +
> +&pcs_mdio9 {
> + status = "okay";
> +};
> +
> +&pcs_mdio10 {
> + status = "okay";
> +};
> +
> +&spi_bridge {
> + sw1: ethernet-switch@0 {
> + compatible = "nxp,sja1110a";
> + reg = <0>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 0>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + /* SW1_P1 */
> + port@1 {
> + reg = <1>;
> + label = "con_2x20";
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac17>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p1";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw1_mii3_phy>;
> + };
> +
> + sw1p4: port@4 {
> + reg = <4>;
> + link = <&sw2p1>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx1";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx2";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx3";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx4";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx5";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx6";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw1_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw1_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw1_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw1_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw1_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw1_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +
> + sw2: ethernet-switch@2 {
> + compatible = "nxp,sja1110a";
> + reg = <2>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 1>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + sw2p1: port@1 {
> + reg = <1>;
> + link = <&sw1p4>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac18>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p2";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw2_mii3_phy>;
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "to_sw3";
> + phy-mode = "2500base-x";
> +
> + fixed-link {
> + speed = <2500>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx7";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx8";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx9";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx10";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx11";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx12";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw2_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw2_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw2_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw2_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw2_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw2_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board
@ 2021-10-04 3:43 ` Shawn Guo
0 siblings, 0 replies; 12+ messages in thread
From: Shawn Guo @ 2021-10-04 3:43 UTC (permalink / raw)
To: Vladimir Oltean
Cc: devicetree, linux-kernel, linux-arm-kernel, netdev, Rob Herring,
Li Yang, Wasim Khan, Vabhav Sharma, Kuldeep Singh,
Florin Chiculita, Biwen Li, Heinz Wrobel, Yangbo Lu
On Fri, Aug 27, 2021 at 11:27:22PM +0300, Vladimir Oltean wrote:
> From: Wasim Khan <wasim.khan@nxp.com>
>
> The NXP BlueBox3 is a prototyping board for high-performance autonomous
> driving systems. It contains two Linux systems, on running on the
s/on running/running
> LX2160A and the other on the S32G2 SoC. This patch adds the device tree
> support for the LX2160A SoC.
>
> In terms of networking from the LX2160A's perspective, there are:
>
> - 4 RJ45 10G ports using Aquantia copper PHYs which are attached
> directly to DPAA2 ports on the LX2160A
>
> - 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
> the LX2160A (each switch has a host port towards a dpmac), the third
> switch is managed by the S32G2. All 3 switches are interconnected
> through on-board SERDES lanes. The cascade ports between the 2
> switches managed by LX2160A form a DSA link, the cascade ports between
> the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
> device).
>
> - 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
> to NXP SJA1110 switches
>
> - 12 automotive 100base-T1 single-pair Ethernet ports routed from the
> SJA1110 internal PHY ports (TJA1103)
>
> - One SGMII SERDES lane towards an internal connector, attached to one
> of the SJA1110 switch ports
>
> On board rev A, the AR8035 RGMII PHY addresses were different than on
> rev B and later. This patch introduces a separate device tree for rev A.
> The main device tree is supposed to cover rev B and later.
>
> Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
> Co-developed-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> Co-developed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
> Co-developed-by: Biwen Li <biwen.li@nxp.com>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
> Co-developed-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Signed-off-by: Heinz Wrobel <Heinz.Wrobel@nxp.com>
> Co-developed-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 2 +
> .../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 +
> .../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++
> 3 files changed, 694 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..ecf74464705f 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> new file mode 100644
> index 000000000000..15d273c93154
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a-bluebox3.dts"
> +
> +/ {
> + compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
> +};
> +
> +/* The RGMII PHYs have a different MDIO address */
> +&emdio1 {
> + /delete-node/ ethernet-phy@5;
> +
> + sw1_mii3_phy: ethernet-phy@1 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x1>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + /delete-node/ ethernet-phy@6;
> +
> + sw2_mii3_phy: ethernet-phy@2 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x2>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> new file mode 100644
> index 000000000000..be7d01630a6f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
> @@ -0,0 +1,658 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2160A BLUEBOX3
> +//
> +// Copyright 2020-2021 NXP
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +
> +/ {
> + model = "NXP Layerscape LX2160ABLUEBOX3";
> + compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
> +
> + aliases {
> + crypto = &crypto;
> + serial0 = &uart0;
> + mmc0 = &esdhc0;
> + mmc1 = &esdhc1;
It's nice to have them sort alphabetically.
I fixed them up and applied the patch.
Shawn
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + sb_3v3: regulator-sb3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "MC34717-3.3VSB";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +};
> +
> +&can0 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&can1 {
> + status = "okay";
> +
> + can-transceiver {
> + max-bitrate = <5000000>;
> + };
> +};
> +
> +&crypto {
> + status = "okay";
> +};
> +
> +&dpmac5 {
> + phy-handle = <&aqr113c_phy1>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac6 {
> + phy-handle = <&aqr113c_phy2>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac9 {
> + phy-handle = <&aqr113c_phy3>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac10 {
> + phy-handle = <&aqr113c_phy4>;
> + phy-mode = "usxgmii";
> + managed = "in-band-status";
> +};
> +
> +&dpmac17 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&dpmac18 {
> + phy-mode = "rgmii";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&emdio1 {
> + status = "okay";
> +
> + aqr113c_phy2: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY2 */
> + interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy1: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY1 */
> + interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw1_mii3_phy: ethernet-phy@5 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x5>;
> + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + sw2_mii3_phy: ethernet-phy@6 {
> + /* AR8035 */
> + compatible = "ethernet-phy-id004d.d072";
> + reg = <0x6>;
> + interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&emdio2 {
> + status = "okay";
> +
> + aqr113c_phy4: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x0>;
> + /* IRQ_10G_PHY4 */
> + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + aqr113c_phy3: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x8>;
> + /* IRQ_10G_PHY3 */
> + interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&esdhc0 {
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&fspi {
> + status = "okay";
> +
> + mt35xu512aba0: flash@0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +
> + mt35xu512aba1: flash@1 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <8>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9547";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x2>;
> +
> + power-monitor@40 {
> + compatible = "ti,ina220";
> + reg = <0x40>;
> + shunt-resistor = <500>;
> + };
> + };
> +
> + i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x3>;
> +
> + temp2: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + temp1: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4>;
> +
> + rtc@51 {
> + compatible = "nxp,pcf2129";
> + reg = <0x51>;
> + interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + i2c-mux@75 {
> + compatible = "nxp,pca9547";
> + reg = <0x75>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0>;
> +
> + spi_bridge: spi@28 {
> + compatible = "nxp,sc18is602b";
> + reg = <0x28>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +
> + i2c-mux@77 {
> + compatible = "nxp,pca9846";
> + reg = <0x77>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x1>;
> +
> + /* The I2C multiplexer and temperature sensors are on
> + * the T6 riser card.
> + */
> + i2c-mux@70 {
> + compatible = "nxp,pca9548";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c@6 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x6>;
> +
> + q12: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> +
> + i2c@7 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x7>;
> +
> + q11: temperature-sensor@4c {
> + compatible = "nxp,sa56004";
> + reg = <0x4c>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q13: temperature-sensor@48 {
> + compatible = "nxp,sa56004";
> + reg = <0x48>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + q14: temperature-sensor@4a {
> + compatible = "nxp,sa56004";
> + reg = <0x4a>;
> + vcc-supply = <&sb_3v3>;
> + #thermal-sensor-cells = <1>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&pcs_mdio5 {
> + status = "okay";
> +};
> +
> +&pcs_mdio6 {
> + status = "okay";
> +};
> +
> +&pcs_mdio9 {
> + status = "okay";
> +};
> +
> +&pcs_mdio10 {
> + status = "okay";
> +};
> +
> +&spi_bridge {
> + sw1: ethernet-switch@0 {
> + compatible = "nxp,sja1110a";
> + reg = <0>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 0>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + /* SW1_P1 */
> + port@1 {
> + reg = <1>;
> + label = "con_2x20";
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac17>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p1";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw1_mii3_phy>;
> + };
> +
> + sw1p4: port@4 {
> + reg = <4>;
> + link = <&sw2p1>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx1";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx2";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx3";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx4";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx5";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx6";
> + phy-mode = "internal";
> + phy-handle = <&sw1_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw1_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw1_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw1_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw1_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw1_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw1_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +
> + sw2: ethernet-switch@2 {
> + compatible = "nxp,sja1110a";
> + reg = <2>;
> + spi-max-frequency = <4000000>;
> + spi-cpol;
> + dsa,member = <0 1>;
> +
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microcontroller port */
> + port@0 {
> + reg = <0>;
> + status = "disabled";
> + };
> +
> + sw2p1: port@1 {
> + reg = <1>;
> + link = <&sw1p4>;
> + phy-mode = "sgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + ethernet = <&dpmac18>;
> + phy-mode = "rgmii-id";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "1ge_p2";
> + phy-mode = "rgmii-id";
> + phy-handle = <&sw2_mii3_phy>;
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "to_sw3";
> + phy-mode = "2500base-x";
> +
> + fixed-link {
> + speed = <2500>;
> + full-duplex;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + label = "trx7";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port5_base_t1_phy>;
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "trx8";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port6_base_t1_phy>;
> + };
> +
> + port@7 {
> + reg = <7>;
> + label = "trx9";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port7_base_t1_phy>;
> + };
> +
> + port@8 {
> + reg = <8>;
> + label = "trx10";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port8_base_t1_phy>;
> + };
> +
> + port@9 {
> + reg = <9>;
> + label = "trx11";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port9_base_t1_phy>;
> + };
> +
> + port@a {
> + reg = <10>;
> + label = "trx12";
> + phy-mode = "internal";
> + phy-handle = <&sw2_port10_base_t1_phy>;
> + };
> + };
> +
> + mdios {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + compatible = "nxp,sja1110-base-t1-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + sw2_port5_base_t1_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x1>;
> + };
> +
> + sw2_port6_base_t1_phy: ethernet-phy@2 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x2>;
> + };
> +
> + sw2_port7_base_t1_phy: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x3>;
> + };
> +
> + sw2_port8_base_t1_phy: ethernet-phy@4 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x4>;
> + };
> +
> + sw2_port9_base_t1_phy: ethernet-phy@5 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x5>;
> + };
> +
> + sw2_port10_base_t1_phy: ethernet-phy@6 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <0x6>;
> + };
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> +};
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread