[PATCH v3 28/29] arm: dts: ls1028a: sync the fsl-ls1028a.dtsi with linux

[Michael Walle <michael@walle.cc>]

Now that everything is prepared, copy the fsl-ls1028a.dtsi from the
linux kernel v5.14.

Notable changes:
 - second watchdog added
 - the number of chip selects of the SPI controller is now correct and
   reflects what the hardware offers
 - the LPUARTs have the correct clock parent
 - USB controllers are enabled by default, which was already the case
   before this sync because all board enabled all the USB controller
   nodes. A linux patch to fix this is pending.
 - the eSDHC controller changes from big-endian to little-endian, but
   that property seems to be not used at all.

Signed-off-by: Michael Walle <michael@walle.cc>
---
 arch/arm/dts/fsl-ls1028a.dtsi                 | 861 ++++++++++++++++--
 .../dt-bindings/clock/fsl,qoriq-clockgen.h    |  15 +
 2 files changed, 786 insertions(+), 90 deletions(-)
 create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.h

diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi
index af6dabe847..343ecf0e89 100644
--- a/arch/arm/dts/fsl-ls1028a.dtsi
+++ b/arch/arm/dts/fsl-ls1028a.dtsi
@@ -1,12 +1,16 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * NXP ls1028a SOC common device tree source
+ * Device Tree Include file for NXP Layerscape-1028A family SoC.
  *
- * Copyright 2019-2020 NXP
+ * Copyright 2018-2020 NXP
+ *
+ * Harninder Rai <harninder.rai@nxp.com>
  *
  */
 
+#include <dt-bindings/clock/fsl,qoriq-clockgen.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	compatible = "fsl,ls1028a";
@@ -14,6 +18,54 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x0>;
+			enable-method = "psci";
+			clocks = <&clockgen QORIQ_CLK_CMUX 0>;
+			next-level-cache = <&l2>;
+			cpu-idle-states = <&CPU_PW20>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x1>;
+			enable-method = "psci";
+			clocks = <&clockgen QORIQ_CLK_CMUX 0>;
+			next-level-cache = <&l2>;
+			cpu-idle-states = <&CPU_PW20>;
+			#cooling-cells = <2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
+	};
+
+	idle-states {
+		/*
+		 * PSCI node is not added default, U-boot will add missing
+		 * parts if it determines to use PSCI.
+		 */
+		entry-method = "psci";
+
+		CPU_PW20: cpu-pw20 {
+			  compatible = "arm,idle-state";
+			  idle-state-name = "PW20";
+			  arm,psci-suspend-param = <0x0>;
+			  entry-latency-us = <2000>;
+			  exit-latency-us = <2000>;
+			  min-residency-us = <6000>;
+		};
+	};
+
 	sysclk: sysclk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -21,14 +73,33 @@
 		clock-output-names = "sysclk";
 	};
 
-	gic: interrupt-controller@6000000 {
-		compatible = "arm,gic-v3";
-		reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
-			  <0x0 0x06040000 0 0x40000>;
-		#interrupt-cells = <3>;
-		interrupt-controller;
-		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
-					 IRQ_TYPE_LEVEL_LOW)>;
+	osc_27m: clock-osc-27m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+		clock-output-names = "phy_27m";
+	};
+
+	dpclk: clock-controller@f1f0000 {
+		compatible = "fsl,ls1028a-plldig";
+		reg = <0x0 0xf1f0000 0x0 0xffff>;
+		#clock-cells = <0>;
+		clocks = <&osc_27m>;
+	};
+
+	firmware {
+		optee: optee  {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+			status = "disabled";
+		};
+	};
+
+	reboot {
+		compatible ="syscon-reboot";
+		regmap = <&rst>;
+		offset = <0>;
+		mask = <0x02>;
 	};
 
 	timer {
@@ -43,13 +114,123 @@
 					  IRQ_TYPE_LEVEL_LOW)>;
 	};
 
+	pmu {
+		compatible = "arm,cortex-a72-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gic: interrupt-controller@6000000 {
+		compatible= "arm,gic-v3";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		reg= <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+			<0x0 0x06040000 0 0x40000>; /* GIC Redistributor */
+		#interrupt-cells= <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
+					 IRQ_TYPE_LEVEL_LOW)>;
+		its: gic-its@6020000 {
+			compatible = "arm,gic-v3-its";
+			msi-controller;
+			reg = <0x0 0x06020000 0 0x20000>;/* GIC Translater */
+		};
+	};
+
+	thermal-zones {
+		ddr-controller {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+				ddr-ctrler-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				ddr-ctrler-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		core-cluster {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 1>;
+
+			trips {
+				core_cluster_alert: core-cluster-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				core_cluster_crit: core-cluster-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&core_cluster_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	soc: soc {
 		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
 
-		clockgen: clocking@1300000 {
+		ddr: memory-controller@1080000 {
+			compatible = "fsl,qoriq-memory-controller";
+			reg = <0x0 0x1080000 0x0 0x1000>;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			little-endian;
+		};
+
+		dcfg: syscon@1e00000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,ls1028a-dcfg", "syscon", "simple-mfd";
+			reg = <0x0 0x1e00000 0x0 0x10000>;
+			ranges = <0x0 0x0 0x1e00000 0x10000>;
+			little-endian;
+
+			fspi_clk: clock-controller@900 {
+				compatible = "fsl,ls1028a-flexspi-clk";
+				reg = <0x900 0x4>;
+				#clock-cells = <0>;
+				clocks = <&clockgen QORIQ_CLK_HWACCEL 0>;
+				clock-output-names = "fspi_clk";
+			};
+		};
+
+		rst: syscon@1e60000 {
+			compatible = "syscon";
+			reg = <0x0 0x1e60000 0x0 0x10000>;
+			little-endian;
+		};
+
+		scfg: syscon@1fc0000 {
+			compatible = "fsl,ls1028a-scfg", "syscon";
+			reg = <0x0 0x1fc0000 0x0 0x10000>;
+			big-endian;
+		};
+
+		clockgen: clock-controller@1300000 {
 			compatible = "fsl,ls1028a-clockgen";
 			reg = <0x0 0x1300000 0x0 0xa0000>;
 			#clock-cells = <2>;
@@ -62,8 +243,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2000000 0x0 0x10000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -73,8 +254,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2010000 0x0 0x10000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -84,8 +265,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2020000 0x0 0x10000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -95,8 +276,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2030000 0x0 0x10000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -106,8 +287,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2040000 0x0 0x10000>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -117,8 +298,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2050000 0x0 0x10000>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -128,8 +309,8 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2060000 0x0 0x10000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
@@ -139,151 +320,237 @@
 			#size-cells = <0>;
 			reg = <0x0 0x2070000 0x0 0x10000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "i2c";
-			clocks = <&clockgen 4 0>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
 			status = "disabled";
 		};
 
-		fspi: flexspi@20c0000 {
+		fspi: spi@20c0000 {
 			compatible = "nxp,lx2160a-fspi";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x20c0000 0x0 0x10000>,
 			      <0x0 0x20000000 0x0 0x10000000>;
 			reg-names = "fspi_base", "fspi_mmap";
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "fspi_en", "fspi";
 			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&fspi_clk>, <&fspi_clk>;
+			clock-names = "fspi_en", "fspi";
 			status = "disabled";
 		};
 
-		dspi0: dspi@2100000 {
+		dspi0: spi@2100000 {
 			compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2100000 0x0 0x10000>;
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "dspi";
-			clocks = <&clockgen 4 0>;
-			spi-num-chipselects = <5>;
-			litte-endian;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			dmas = <&edma0 0 62>, <&edma0 0 60>;
+			dma-names = "tx", "rx";
+			spi-num-chipselects = <4>;
+			little-endian;
 			status = "disabled";
 		};
 
-		dspi1: dspi@2110000 {
+		dspi1: spi@2110000 {
 			compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2110000 0x0 0x10000>;
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "dspi";
-			clocks = <&clockgen 4 0>;
-			spi-num-chipselects = <5>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			dmas = <&edma0 0 58>, <&edma0 0 56>;
+			dma-names = "tx", "rx";
+			spi-num-chipselects = <4>;
 			little-endian;
 			status = "disabled";
 		};
 
-		dspi2: dspi@2120000 {
+		dspi2: spi@2120000 {
 			compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2120000 0x0 0x10000>;
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "dspi";
-			clocks = <&clockgen 4 0>;
-			spi-num-chipselects = <5>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			dmas = <&edma0 0 54>, <&edma0 0 2>;
+			dma-names = "tx", "rx";
+			spi-num-chipselects = <3>;
 			little-endian;
 			status = "disabled";
 		};
 
-		esdhc: esdhc@2140000 {
-			compatible = "fsl,esdhc";
+		esdhc: mmc@2140000 {
+			compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
 			reg = <0x0 0x2140000 0x0 0x10000>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			big-endian;
+			clock-frequency = <0>; /* fixed up by bootloader */
+			clocks = <&clockgen QORIQ_CLK_HWACCEL 1>;
+			voltage-ranges = <1800 1800 3300 3300>;
+			sdhci,auto-cmd12;
+			little-endian;
 			bus-width = <4>;
 			status = "disabled";
 		};
 
-		esdhc1: esdhc@2150000 {
-			compatible = "fsl,esdhc";
+		esdhc1: mmc@2150000 {
+			compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
 			reg = <0x0 0x2150000 0x0 0x10000>;
 			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
-			big-endian;
+			clock-frequency = <0>; /* fixed up by bootloader */
+			clocks = <&clockgen QORIQ_CLK_HWACCEL 1>;
+			voltage-ranges = <1800 1800 3300 3300>;
+			sdhci,auto-cmd12;
+			broken-cd;
+			little-endian;
 			bus-width = <4>;
 			status = "disabled";
 		};
 
+		can0: can@2180000 {
+			compatible = "fsl,lx2160ar1-flexcan";
+			reg = <0x0 0x2180000 0x0 0x10000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "ipg", "per";
+			status = "disabled";
+		};
+
+		can1: can@2190000 {
+			compatible = "fsl,lx2160ar1-flexcan";
+			reg = <0x0 0x2190000 0x0 0x10000>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "ipg", "per";
+			status = "disabled";
+		};
+
 		duart0: serial@21c0500 {
-			device_type = "serial";
 			compatible = "fsl,ns16550", "ns16550a";
-			reg = <0x0 0x21c0500 0x0 0x100>;
+			reg = <0x00 0x21c0500 0x0 0x100>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
 		duart1: serial@21c0600 {
-			device_type = "serial";
 			compatible = "fsl,ns16550", "ns16550a";
-			reg = <0x0 0x21c0600 0x0 0x100>;
+			reg = <0x00 0x21c0600 0x0 0x100>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
+
 		lpuart0: serial@2260000 {
 			compatible = "fsl,ls1028a-lpuart";
 			reg = <0x0 0x2260000 0x0 0x1000>;
-			interrupts = <0 232 0x4>;
-			clocks = <&sysclk>;
+			interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 32>,
+			       <&edma0 1 33>;
 			status = "disabled";
 		};
 
 		lpuart1: serial@2270000 {
 			compatible = "fsl,ls1028a-lpuart";
 			reg = <0x0 0x2270000 0x0 0x1000>;
-			interrupts = <0 233 0x4>;
-			clocks = <&sysclk>;
+			interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 30>,
+			       <&edma0 1 31>;
 			status = "disabled";
 		};
 
 		lpuart2: serial@2280000 {
 			compatible = "fsl,ls1028a-lpuart";
 			reg = <0x0 0x2280000 0x0 0x1000>;
-			interrupts = <0 234 0x4>;
-			clocks = <&sysclk>;
+			interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 28>,
+			       <&edma0 1 29>;
 			status = "disabled";
 		};
 
 		lpuart3: serial@2290000 {
 			compatible = "fsl,ls1028a-lpuart";
 			reg = <0x0 0x2290000 0x0 0x1000>;
-			interrupts = <0 235 0x4>;
-			clocks = <&sysclk>;
+			interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 26>,
+			       <&edma0 1 27>;
 			status = "disabled";
 		};
 
 		lpuart4: serial@22a0000 {
 			compatible = "fsl,ls1028a-lpuart";
 			reg = <0x0 0x22a0000 0x0 0x1000>;
-			interrupts = <0 236 0x4>;
-			clocks = <&sysclk>;
+			interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 24>,
+			       <&edma0 1 25>;
 			status = "disabled";
 		};
 
 		lpuart5: serial@22b0000 {
 			compatible = "fsl,ls1028a-lpuart";
 			reg = <0x0 0x22b0000 0x0 0x1000>;
-			interrupts = <0 237 0x4>;
-			clocks = <&sysclk>;
+			interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 22>,
+			       <&edma0 1 23>;
 			status = "disabled";
 		};
 
+		edma0: dma-controller@22c0000 {
+			#dma-cells = <2>;
+			compatible = "fsl,ls1028a-edma", "fsl,vf610-edma";
+			reg = <0x0 0x22c0000 0x0 0x10000>,
+			      <0x0 0x22d0000 0x0 0x10000>,
+			      <0x0 0x22e0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "edma-tx", "edma-err";
+			dma-channels = <32>;
+			clock-names = "dmamux0", "dmamux1";
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+		};
+
 		gpio1: gpio@2300000 {
 			compatible = "fsl,ls1028a-gpio","fsl,qoriq-gpio";
 			reg = <0x0 0x2300000 0x0 0x10000>;
@@ -317,28 +584,34 @@
 			little-endian;
 		};
 
-		usb0: usb3@3100000 {
+		usb0: usb@3100000 {
 			compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
 			reg = <0x0 0x3100000 0x0 0x10000>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			dr_mode = "host";
-			status = "disabled";
+			snps,dis_rxdet_inp3_quirk;
+			snps,quirk-frame-length-adjustment = <0x20>;
+			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
 		};
 
-		usb1: usb3@3110000 {
+		usb1: usb@3110000 {
 			compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
 			reg = <0x0 0x3110000 0x0 0x10000>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			dr_mode = "host";
-			status = "disabled";
+			snps,dis_rxdet_inp3_quirk;
+			snps,quirk-frame-length-adjustment = <0x20>;
+			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
 		};
 
 		sata: sata@3200000 {
 			compatible = "fsl,ls1028a-ahci";
-			reg = <0x0 0x3200000 0x0 0x10000	/* ccsr sata base */
-			       0x7 0x100520  0x0 0x4>;		/* ecc sata addr*/
+			reg = <0x0 0x3200000 0x0 0x10000>,
+				<0x7 0x100520 0x0 0x4>;
 			reg-names = "ahci", "sata-ecc";
 			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -347,12 +620,25 @@
 			reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers */
 			      <0x80 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; /* aer interrupt */
+			interrupt-names = "pme", "aer";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			dma-coherent;
+			num-viewport = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
@@ -361,44 +647,380 @@
 			reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */
 			      <0x88 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme", "aer";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
+			dma-coherent;
+			num-viewport = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0 0x00010000   /* downstream I/O */
 				  0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+			msi-parent = <&its>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 2 &gic 0 0 GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 3 &gic 0 0 GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					<0000 0 0 4 &gic 0 0 GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
 			status = "disabled";
 		};
 
-		cluster1_core0_watchdog: wdt@c000000 {
+		smmu: iommu@5000000 {
+			compatible = "arm,mmu-500";
+			reg = <0 0x5000000 0 0x800000>;
+			#global-interrupts = <8>;
+			#iommu-cells = <1>;
+			stream-match-mask = <0x7c00>;
+			/* global secure fault */
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			/* combined secure interrupt */
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			/* global non-secure fault */
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+			/* combined non-secure interrupt */
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+			/* performance counter interrupts 0-7 */
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+			/* per context interrupt, 64 interrupts */
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		crypto: crypto@8000000 {
+			compatible = "fsl,sec-v5.0", "fsl,sec-v4.0";
+			fsl,sec-era = <10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x00 0x8000000 0x100000>;
+			reg = <0x00 0x8000000 0x0 0x100000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+
+			sec_jr0: jr@10000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg	= <0x10000 0x10000>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sec_jr1: jr@20000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg	= <0x20000 0x10000>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sec_jr2: jr@30000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg	= <0x30000 0x10000>;
+				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sec_jr3: jr@40000 {
+				compatible = "fsl,sec-v5.0-job-ring",
+					     "fsl,sec-v4.0-job-ring";
+				reg	= <0x40000 0x10000>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		qdma: dma-controller@8380000 {
+			compatible = "fsl,ls1028a-qdma", "fsl,ls1021a-qdma";
+			reg = <0x0 0x8380000 0x0 0x1000>, /* Controller regs */
+			      <0x0 0x8390000 0x0 0x10000>, /* Status regs */
+			      <0x0 0x83a0000 0x0 0x40000>; /* Block regs */
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "qdma-error", "qdma-queue0",
+				"qdma-queue1", "qdma-queue2", "qdma-queue3";
+			dma-channels = <8>;
+			block-number = <1>;
+			block-offset = <0x10000>;
+			fsl,dma-queues = <2>;
+			status-sizes = <64>;
+			queue-sizes = <64 64>;
+		};
+
+		cluster1_core0_watchdog: watchdog@c000000 {
 			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(16)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(16)>;
+			clock-names = "wdog_clk", "apb_pclk";
+		};
+
+		cluster1_core1_watchdog: watchdog@c010000 {
+			compatible = "arm,sp805", "arm,primecell";
+			reg = <0x0 0xc010000 0x0 0x1000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(16)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(16)>;
+			clock-names = "wdog_clk", "apb_pclk";
+		};
+
+		sai1: audio-controller@f100000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0xf100000 0x0 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 4>,
+			       <&edma0 1 3>;
+			fsl,sai-asynchronous;
+			status = "disabled";
+		};
+
+		sai2: audio-controller@f110000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0xf110000 0x0 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 6>,
+			       <&edma0 1 5>;
+			fsl,sai-asynchronous;
+			status = "disabled";
+		};
+
+		sai3: audio-controller@f120000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0xf120000 0x0 0x10000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 8>,
+			       <&edma0 1 7>;
+			fsl,sai-asynchronous;
+			status = "disabled";
+		};
+
+		sai4: audio-controller@f130000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0xf130000 0x0 0x10000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 10>,
+			       <&edma0 1 9>;
+			fsl,sai-asynchronous;
+			status = "disabled";
+		};
+
+		sai5: audio-controller@f140000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0xf140000 0x0 0x10000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 12>,
+			       <&edma0 1 11>;
+			fsl,sai-asynchronous;
+			status = "disabled";
+		};
+
+		sai6: audio-controller@f150000 {
+			#sound-dai-cells = <0>;
+			compatible = "fsl,vf610-sai";
+			reg = <0x0 0xf150000 0x0 0x10000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>,
+				 <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
+			clock-names = "bus", "mclk1", "mclk2", "mclk3";
+			dma-names = "tx", "rx";
+			dmas = <&edma0 1 14>,
+			       <&edma0 1 13>;
+			fsl,sai-asynchronous;
+			status = "disabled";
 		};
 
-		pcie@1f0000000 {
+		tmu: tmu@1f80000 {
+			compatible = "fsl,qoriq-tmu";
+			reg = <0x0 0x1f80000 0x0 0x10000>;
+			interrupts = <0 23 0x4>;
+			fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>;
+			fsl,tmu-calibration = <0x00000000 0x00000024
+					       0x00000001 0x0000002b
+					       0x00000002 0x00000031
+					       0x00000003 0x00000038
+					       0x00000004 0x0000003f
+					       0x00000005 0x00000045
+					       0x00000006 0x0000004c
+					       0x00000007 0x00000053
+					       0x00000008 0x00000059
+					       0x00000009 0x00000060
+					       0x0000000a 0x00000066
+					       0x0000000b 0x0000006d
+
+					       0x00010000 0x0000001c
+					       0x00010001 0x00000024
+					       0x00010002 0x0000002c
+					       0x00010003 0x00000035
+					       0x00010004 0x0000003d
+					       0x00010005 0x00000045
+					       0x00010006 0x0000004d
+					       0x00010007 0x00000055
+					       0x00010008 0x0000005e
+					       0x00010009 0x00000066
+					       0x0001000a 0x0000006e
+
+					       0x00020000 0x00000018
+					       0x00020001 0x00000022
+					       0x00020002 0x0000002d
+					       0x00020003 0x00000038
+					       0x00020004 0x00000043
+					       0x00020005 0x0000004d
+					       0x00020006 0x00000058
+					       0x00020007 0x00000063
+					       0x00020008 0x0000006e
+
+					       0x00030000 0x00000010
+					       0x00030001 0x0000001c
+					       0x00030002 0x00000029
+					       0x00030003 0x00000036
+					       0x00030004 0x00000042
+					       0x00030005 0x0000004f
+					       0x00030006 0x0000005b
+					       0x00030007 0x00000068>;
+			little-endian;
+			#thermal-sensor-cells = <1>;
+		};
+
+		pcie@1f0000000 { /* Integrated Endpoint Root Complex */
 			compatible = "pci-host-ecam-generic";
-			/* ECAM bus 0, HW has more space reserved but not populated */
-			bus-range = <0x0 0x0>;
 			reg = <0x01 0xf0000000 0x0 0x100000>;
 			#address-cells = <3>;
 			#size-cells = <2>;
+			msi-parent = <&its>;
 			device_type = "pci";
-			ranges = <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>;
+			bus-range = <0x0 0x0>;
+			dma-coherent;
+			msi-map = <0 &its 0x17 0xe>;
+			iommu-map = <0 &smmu 0x17 0xe>;
+				  /* PF0-6 BAR0 - non-prefetchable memory */
+			ranges = <0x82000000 0x1 0xf8000000  0x1 0xf8000000  0x0 0x160000
+				  /* PF0-6 BAR2 - prefetchable memory */
+				  0xc2000000 0x1 0xf8160000  0x1 0xf8160000  0x0 0x070000
+				  /* PF0: VF0-1 BAR0 - non-prefetchable memory */
+				  0x82000000 0x1 0xf81d0000  0x1 0xf81d0000  0x0 0x020000
+				  /* PF0: VF0-1 BAR2 - prefetchable memory */
+				  0xc2000000 0x1 0xf81f0000  0x1 0xf81f0000  0x0 0x020000
+				  /* PF1: VF0-1 BAR0 - non-prefetchable memory */
+				  0x82000000 0x1 0xf8210000  0x1 0xf8210000  0x0 0x020000
+				  /* PF1: VF0-1 BAR2 - prefetchable memory */
+				  0xc2000000 0x1 0xf8230000  0x1 0xf8230000  0x0 0x020000
+				  /* BAR4 (PF5) - non-prefetchable memory */
+				  0x82000000 0x1 0xfc000000  0x1 0xfc000000  0x0 0x400000>;
 
-			enetc_port0: pci@0,0 {
+			enetc_port0: ethernet@0,0 {
+				compatible = "fsl,enetc";
 				reg = <0x000000 0 0 0 0>;
 				status = "disabled";
 			};
 
-			enetc_port1: pci@0,1 {
+			enetc_port1: ethernet@0,1 {
+				compatible = "fsl,enetc";
 				reg = <0x000100 0 0 0 0>;
 				status = "disabled";
 			};
 
-			enetc_port2: pci@0,2 {
+			enetc_port2: ethernet@0,2 {
+				compatible = "fsl,enetc";
 				reg = <0x000200 0 0 0 0>;
-				status = "disabled";
 				phy-mode = "internal";
+				status = "disabled";
 
 				fixed-link {
 					speed = <2500>;
@@ -406,26 +1028,32 @@
 				};
 			};
 
-			enetc_mdio_pf3: pci@0,3 {
-				#address-cells=<0>;
-				#size-cells=<1>;
+			enetc_mdio_pf3: mdio@0,3 {
+				compatible = "fsl,enetc-mdio";
 				reg = <0x000300 0 0 0 0>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
+			ethernet@0,4 {
+				compatible = "fsl,enetc-ptp";
+				reg = <0x000400 0 0 0 0>;
+				clocks = <&clockgen QORIQ_CLK_HWACCEL 3>;
+				little-endian;
+				fsl,extts-fifo;
 			};
 
-			mscc_felix: pci@0,5 {
+			mscc_felix: ethernet-switch@0,5 {
 				reg = <0x000500 0 0 0 0>;
+				/* IEP INT_B */
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
+					/* External ports */
 					mscc_felix_port0: port@0 {
 						reg = <0>;
 						status = "disabled";
@@ -446,6 +1074,7 @@
 						status = "disabled";
 					};
 
+					/* Internal ports */
 					mscc_felix_port4: port@4 {
 						reg = <4>;
 						phy-mode = "internal";
@@ -466,15 +1095,67 @@
 							speed = <1000>;
 							full-duplex;
 						};
-
 					};
 				};
 			};
 
-			enetc_port3: pci@0,6 {
+			enetc_port3: ethernet@0,6 {
+				compatible = "fsl,enetc";
 				reg = <0x000600 0 0 0 0>;
-				status = "disabled";
 				phy-mode = "internal";
+				status = "disabled";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			rcec@1f,0 {
+				reg = <0x00f800 0 0 0 0>;
+				/* IEP INT_A */
+				interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		/* Integrated Endpoint Register Block */
+		ierb@1f0800000 {
+			compatible = "fsl,ls1028a-enetc-ierb";
+			reg = <0x01 0xf0800000 0x0 0x10000>;
+		};
+
+		rcpm: power-controller@1e34040 {
+			compatible = "fsl,ls1028a-rcpm", "fsl,qoriq-rcpm-2.1+";
+			reg = <0x0 0x1e34040 0x0 0x1c>;
+			#fsl,rcpm-wakeup-cells = <7>;
+			little-endian;
+		};
+
+		ftm_alarm0: timer@2800000 {
+			compatible = "fsl,ls1028a-ftm-alarm";
+			reg = <0x0 0x2800000 0x0 0x10000>;
+			fsl,rcpm-wakeup = <&rcpm 0x0 0x0 0x0 0x0 0x4000 0x0 0x0>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+
+	malidp0: display@f080000 {
+		compatible = "arm,mali-dp500";
+		reg = <0x0 0xf080000 0x0 0x10000>;
+		interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 223 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "DE", "SE";
+		clocks = <&dpclk>,
+			 <&clockgen QORIQ_CLK_HWACCEL 2>,
+			 <&clockgen QORIQ_CLK_HWACCEL 2>,
+			 <&clockgen QORIQ_CLK_HWACCEL 2>;
+		clock-names = "pxlclk", "mclk", "aclk", "pclk";
+		arm,malidp-output-port-lines = /bits/ 8 <8 8 8>;
+		arm,malidp-arqos-value = <0xd000d000>;
+
+		port {
+			dp0_out: endpoint {
+
 			};
 		};
 	};
diff --git a/include/dt-bindings/clock/fsl,qoriq-clockgen.h b/include/dt-bindings/clock/fsl,qoriq-clockgen.h
new file mode 100644
index 0000000000..ddec7d0bdc
--- /dev/null
+++ b/include/dt-bindings/clock/fsl,qoriq-clockgen.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef DT_CLOCK_FSL_QORIQ_CLOCKGEN_H
+#define DT_CLOCK_FSL_QORIQ_CLOCKGEN_H
+
+#define QORIQ_CLK_SYSCLK	0
+#define QORIQ_CLK_CMUX		1
+#define QORIQ_CLK_HWACCEL	2
+#define QORIQ_CLK_FMAN		3
+#define QORIQ_CLK_PLATFORM_PLL	4
+#define QORIQ_CLK_CORECLK	5
+
+#define QORIQ_CLK_PLL_DIV(x)	((x) - 1)
+
+#endif /* DT_CLOCK_FSL_QORIQ_CLOCKGEN_H */
-- 
2.30.2