* [PATCH v4 0/1] Add basic node support for Mediatek MT8195 SoC
@ 2021-09-22 9:33 ` Seiya Wang
0 siblings, 0 replies; 9+ messages in thread
From: Seiya Wang @ 2021-09-22 9:33 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring
Cc: linux-arm-kernel, linux-mediatek, devicetree, linux-kernel,
srv_heupstream
MT8195 is a SoC based on 64bit ARMv8 architecture.
It contains 4 CA55 and 4 CA78 cores.
MT8195 share many HW IP with MT65xx series.
This patchset was tested on MT8195 evaluation board to shell.
Based on next-20210916
Changes in v4
Add clock, i2c, pwrap, xhci nodes
Use clock driver instead of dummy clock
Remove ufsphy node
Changes in v3
Add spi and pinctrl nodes
Changes in v2
Fix make dt_binding_check warning in mediatek,ufs-phy.yaml
Update usb phy and ufs phy nodes in mt8195.dtsi
Seiya Wang (1):
arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and
Makefile
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 ++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 561 ++++++++++++++++++++++++++++
3 files changed, 591 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
--
2.14.1
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v4 0/1] Add basic node support for Mediatek MT8195 SoC
@ 2021-09-22 9:33 ` Seiya Wang
0 siblings, 0 replies; 9+ messages in thread
From: Seiya Wang @ 2021-09-22 9:33 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring
Cc: linux-arm-kernel, linux-mediatek, devicetree, linux-kernel,
srv_heupstream
MT8195 is a SoC based on 64bit ARMv8 architecture.
It contains 4 CA55 and 4 CA78 cores.
MT8195 share many HW IP with MT65xx series.
This patchset was tested on MT8195 evaluation board to shell.
Based on next-20210916
Changes in v4
Add clock, i2c, pwrap, xhci nodes
Use clock driver instead of dummy clock
Remove ufsphy node
Changes in v3
Add spi and pinctrl nodes
Changes in v2
Fix make dt_binding_check warning in mediatek,ufs-phy.yaml
Update usb phy and ufs phy nodes in mt8195.dtsi
Seiya Wang (1):
arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and
Makefile
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 ++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 561 ++++++++++++++++++++++++++++
3 files changed, 591 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
--
2.14.1
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v4 0/1] Add basic node support for Mediatek MT8195 SoC
@ 2021-09-22 9:33 ` Seiya Wang
0 siblings, 0 replies; 9+ messages in thread
From: Seiya Wang @ 2021-09-22 9:33 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring
Cc: linux-arm-kernel, linux-mediatek, devicetree, linux-kernel,
srv_heupstream
MT8195 is a SoC based on 64bit ARMv8 architecture.
It contains 4 CA55 and 4 CA78 cores.
MT8195 share many HW IP with MT65xx series.
This patchset was tested on MT8195 evaluation board to shell.
Based on next-20210916
Changes in v4
Add clock, i2c, pwrap, xhci nodes
Use clock driver instead of dummy clock
Remove ufsphy node
Changes in v3
Add spi and pinctrl nodes
Changes in v2
Fix make dt_binding_check warning in mediatek,ufs-phy.yaml
Update usb phy and ufs phy nodes in mt8195.dtsi
Seiya Wang (1):
arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and
Makefile
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 ++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 561 ++++++++++++++++++++++++++++
3 files changed, 591 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
--
2.14.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile
2021-09-22 9:33 ` Seiya Wang
(?)
@ 2021-09-22 9:33 ` Seiya Wang
-1 siblings, 0 replies; 9+ messages in thread
From: Seiya Wang @ 2021-09-22 9:33 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring
Cc: linux-arm-kernel, linux-mediatek, devicetree, linux-kernel,
srv_heupstream, Seiya Wang
Add basic chip support for Mediatek MT8195
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 +
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1024 +++++++++++++++++++++++++++
3 files changed, 1054 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..7aa08bb4c078 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -32,4 +32,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
new file mode 100644
index 000000000000..82bb10e9a531
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+/dts-v1/;
+#include "mt8195.dtsi"
+
+/ {
+ model = "MediaTek MT8195 evaluation board";
+ compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
new file mode 100644
index 000000000000..b2ff83882e2e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
@@ -0,0 +1,1024 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/clock/mt8195-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/reset/ti-syscon.h>
+
+/ {
+ compatible = "mediatek,mt8195";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ clk26m: oscillator0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ clk32k: oscillator1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "clk32k";
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x000>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x100>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x200>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x300>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu4: cpu@400 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x400>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu5: cpu@500 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x500>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu6: cpu@600 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x600>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu7: cpu@700 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x700>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ cluster1 {
+ core0 {
+ cpu = <&cpu4>;
+ };
+ core1 {
+ cpu = <&cpu5>;
+ };
+ core2 {
+ cpu = <&cpu6>;
+ };
+ core3 {
+ cpu = <&cpu7>;
+ };
+ };
+ };
+
+ idle-states {
+ entry-method = "arm,psci";
+ cpuoff_l: cpuoff_l {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x00010001>;
+ local-timer-stop;
+ entry-latency-us = <50>;
+ exit-latency-us = <95>;
+ min-residency-us = <580>;
+ };
+ cpuoff_b: cpuoff_b {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x00010001>;
+ local-timer-stop;
+ entry-latency-us = <45>;
+ exit-latency-us = <140>;
+ min-residency-us = <740>;
+ };
+ clusteroff_l: clusteroff_l {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x01010002>;
+ local-timer-stop;
+ entry-latency-us = <55>;
+ exit-latency-us = <155>;
+ min-residency-us = <840>;
+ };
+ clusteroff_b: clusteroff_b {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x01010002>;
+ local-timer-stop;
+ entry-latency-us = <50>;
+ exit-latency-us = <200>;
+ min-residency-us = <1000>;
+ };
+ };
+
+ l2_0: l2-cache0 {
+ compatible = "cache";
+ next-level-cache = <&l3_0>;
+ };
+
+ l2_1: l2-cache1 {
+ compatible = "cache";
+ next-level-cache = <&l3_0>;
+ };
+
+ l3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+
+ dsu-pmu {
+ compatible = "arm,dsu-pmu";
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
+ cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
+ <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+ };
+
+ pmu-a55 {
+ compatible = "arm,cortex-a55-pmu";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
+ };
+
+ pmu-a78 {
+ compatible = "arm,cortex-a78-pmu";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer: timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-frequency = <13000000>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <4>;
+ #redistributor-regions = <1>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c040000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+
+ ppi-partitions {
+ ppi_cluster0: interrupt-partition-0 {
+ affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
+ };
+ ppi_cluster1: interrupt-partition-1 {
+ affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
+ };
+ };
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8195-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg_ao: infracfg_ao@10001000 {
+ compatible = "mediatek,mt8195-infracfg_ao", "syscon", "simple-mfd";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ infracfg_rst: reset-controller {
+ compatible = "ti,syscon-reset";
+ #reset-cells = <1>;
+ ti,reset-bits = <
+ 0x140 18 0x144 18 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x120 1 0x124 1 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x730 1 0x734 1 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x150 5 0x154 5 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ >;
+ };
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8195-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@10005000 {
+ compatible = "mediatek,mt8195-pinctrl";
+ reg = <0 0x10005000 0 0x1000>,
+ <0 0x11d10000 0 0x1000>,
+ <0 0x11d30000 0 0x1000>,
+ <0 0x11d40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11eb0000 0 0x1000>,
+ <0 0x11f40000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
+ "iocfg_br", "iocfg_lm", "iocfg_rb",
+ "iocfg_tl", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 144>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>;
+ #interrupt-cells = <2>;
+
+ pmif_pin: pmif_default_pin {
+ pinmux = <PINMUX_GPIO36__FUNC_RTC32K_CK>,
+ <PINMUX_GPIO40__FUNC_PWRAP_SPI0_CSN>,
+ <PINMUX_GPIO41__FUNC_PWRAP_SPI0_CK>,
+ <PINMUX_GPIO42__FUNC_PWRAP_SPI0_MO>,
+ <PINMUX_GPIO43__FUNC_PWRAP_SPI0_MI>,
+ <PINMUX_GPIO44__FUNC_SPMI_M_SCL>,
+ <PINMUX_GPIO45__FUNC_SPMI_M_SDA>;
+ };
+ };
+
+ watchdog: watchdog@10007000 {
+ compatible = "mediatek,mt8195-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x10007000 0 0x100>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8195-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ systimer: timer@10017000 {
+ compatible = "mediatek,mt8195-timer",
+ "mediatek,mt6765-timer";
+ reg = <0 0x10017000 0 0x1000>;
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_CLK26M_D2>;
+ };
+
+ pwrap: pwrap@10024000 {
+ compatible = "mediatek,mt8195-pwrap", "syscon";
+ reg = <0 0x10024000 0 0x1000>;
+ reg-names = "pwrap";
+ interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
+ <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
+ clock-names = "spi", "wrap";
+ assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmif_pin>;
+ };
+
+ scp_adsp: syscon@10720000 {
+ compatible = "mediatek,mt8195-scp_adsp", "syscon";
+ reg = <0 0x10720000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ uart0: serial@11001100 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001100 0 0x100>;
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART0>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart1: serial@11001200 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001200 0 0x100>;
+ interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART1>;
+ clock-names = "baud", "bus";
+ };
+
+ uart2: serial@11001300 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001300 0 0x100>;
+ interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART2>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart3: serial@11001400 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001400 0 0x100>;
+ interrupts = <GIC_SPI 723 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART3>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart4: serial@11001500 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001500 0 0x100>;
+ interrupts = <GIC_SPI 724 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART4>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart5: serial@11001600 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001600 0 0x100>;
+ interrupts = <GIC_SPI 725 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART5>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ auxadc: auxadc@11002000 {
+ compatible = "mediatek,mt8195-auxadc",
+ "mediatek,mt8173-auxadc";
+ reg = <0 0x11002000 0 0x1000>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_AUXADC>;
+ clock-names = "main";
+ #io-channel-cells = <1>;
+ status = "disabled";
+ };
+
+ pericfg_ao: syscon@11003000 {
+ compatible = "mediatek,mt8195-pericfg_ao", "syscon";
+ reg = <0 0x11003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ spi0: spi@1100a000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi1: spi@11010000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11010000 0 0x100>;
+ interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI1>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi2: spi@11012000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11012000 0 0x100>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI2>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi3: spi@11013000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11013000 0 0x100>;
+ interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI3>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi4: spi@11018000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11018000 0 0x100>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI4>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi5: spi@11019000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11019000 0 0x100>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI5>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spis0: spi@1101d000 {
+ compatible = "mediatek,mt8195-spi-slave";
+ reg = <0 0x1101d000 0 0x100>;
+ interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SPIS0>;
+ clock-names = "spi";
+ assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+ status = "disabled";
+ };
+
+ spis1: spi@1101e000 {
+ compatible = "mediatek,mt8195-spi-slave";
+ reg = <0 0x1101e000 0 0x100>;
+ interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SPIS1>;
+ clock-names = "spi";
+ assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+ status = "disabled";
+ };
+
+ xhci0: xhci@11200000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>,
+ <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u3port0 PHY_TYPE_USB3>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP>,
+ <&topckgen CLK_TOP_SSUSB_XHCI>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SSUSB>,
+ <&infracfg_ao CLK_INFRA_AO_SSUSB_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_REF>,
+ <&apmixedsys CLK_APMIXED_USB1PLL>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck", "mcu_ck";
+ mediatek,syscon-wakeup = <&pericfg 0x400 103>;
+ wakeup-source;
+ status = "disabled";
+ };
+
+ mmc0: mmc@11230000 {
+ compatible = "mediatek,mt8195-mmc",
+ "mediatek,mt8192-mmc";
+ reg = <0 0x11230000 0 0x10000>,
+ <0 0x11f50000 0 0x1000>;
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_MSDC50_0>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC0>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC0_SRC>;
+ clock-names = "source", "hclk", "source_cg";
+ status = "disabled";
+ };
+
+ mmc1: mmc@11240000 {
+ compatible = "mediatek,mt8195-mmc",
+ "mediatek,mt8192-mmc";
+ reg = <0 0x11240000 0 0x1000>,
+ <0 0x11c70000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_MSDC30_1>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC1>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
+ clock-names = "source", "hclk", "source_cg";
+ status = "disabled";
+ };
+
+ xhci1: xhci1@11290000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11290000 0 0x1000>,
+ <0 0x11293e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port1 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_1P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_1P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_1P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P1_REF>,
+ <&apmixedsys CLK_APMIXED_USB1PLL>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck", "mcu_ck";
+ status = "disabled";
+ };
+
+ xhci2: xhci2@112a0000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x112a0000 0 0x1000>,
+ <0 0x112a3e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 533 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_2P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_2P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_2P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_2P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P2_REF>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck";
+ status = "disabled";
+ };
+
+ xhci3: xhci3@112b0000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x112b0000 0 0x1000>,
+ <0 0x112b3e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port3 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_3P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_3P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_3P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_3P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P3_REF>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck";
+ usb2-lpm-disable;
+ status = "disabled";
+ };
+
+ nor_flash: nor@1132c000 {
+ compatible = "mediatek,mt8195-nor",
+ "mediatek,mt8173-nor";
+ reg = <0 0x1132c000 0 0x1000>;
+ interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_SPINOR>,
+ <&pericfg_ao CLK_PERI_AO_FLASHIF_FLASH>,
+ <&pericfg_ao CLK_PERI_AO_FLASHIF_BUS>;
+ clock-names = "spi", "sf", "axi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ u3phy2: t-phy@11c40000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11c40000 0x700>;
+ status = "disabled";
+
+ u2port2: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P2_REF>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ u3phy3: t-phy@11c50000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11c50000 0x700>;
+ status = "disabled";
+
+ u2port3: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P3_REF>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ i2c5: i2c@11d00000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d00000 0 0x1000>,
+ <0 0x10220580 0 0x80>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C5>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@11d01000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d01000 0 0x1000>,
+ <0 0x10220600 0 0x80>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C6>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@11d02000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d02000 0 0x1000>,
+ <0 0x10220680 0 0x80>;
+ interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C7>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ imp_iic_wrap_s: syscon@11d03000 {
+ compatible = "mediatek,mt8195-imp_iic_wrap_s", "syscon";
+ reg = <0 0x11d03000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ i2c0: i2c@11e00000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e00000 0 0x1000>,
+ <0 0x10220080 0 0x80>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C0>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ };
+
+ i2c1: i2c@11e01000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e01000 0 0x1000>,
+ <0 0x10220200 0 0x80>;
+ interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C1>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@11e02000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e02000 0 0x1000>,
+ <0 0x10220380 0 0x80>;
+ interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C2>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@11e03000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e03000 0 0x1000>,
+ <0 0x10220480 0 0x80>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C3>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@11e04000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e04000 0 0x1000>,
+ <0 0x10220500 0 0x80>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C4>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ imp_iic_wrap_w: syscon@11e05000 {
+ compatible = "mediatek,mt8195-imp_iic_wrap_w", "syscon";
+ reg = <0 0x11e05000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ u3phy1: t-phy@11e30000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11e30000 0xe00>;
+ status = "disabled";
+
+ u2port1: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>,
+ <&clk26m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port1: usb-phy@700 {
+ reg = <0x700 0x700>;
+ clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+ <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ u3phy0: t-phy@11e40000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11e40000 0xe00>;
+ status = "disabled";
+
+ u2port0: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_REF>,
+ <&clk26m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port0: usb-phy@700 {
+ reg = <0x700 0x700>;
+ clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+ <&topckgen CLK_TOP_SSUSB_PHY_REF>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ mfgcfg: syscon@13fbf000 {
+ compatible = "mediatek,mt8195-mfgcfg", "syscon";
+ reg = <0 0x13fbf000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vppsys0: syscon@14000000 {
+ compatible = "mediatek,mt8195-vppsys0", "syscon";
+ reg = <0 0x14000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys: syscon@14e00000 {
+ compatible = "mediatek,mt8195-wpesys", "syscon";
+ reg = <0 0x14e00000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys_vpp0: syscon@14e02000 {
+ compatible = "mediatek,mt8195-wpesys_vpp0", "syscon";
+ reg = <0 0x14e02000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys_vpp1: syscon@14e03000 {
+ compatible = "mediatek,mt8195-wpesys_vpp1", "syscon";
+ reg = <0 0x14e03000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vppsys1: syscon@14f00000 {
+ compatible = "mediatek,mt8195-vppsys1", "syscon";
+ reg = <0 0x14f00000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys: syscon@15000000 {
+ compatible = "mediatek,mt8195-imgsys", "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_dip_top: syscon@15110000 {
+ compatible = "mediatek,mt8195-imgsys1_dip_top", "syscon";
+ reg = <0 0x15110000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_dip_nr: syscon@15130000 {
+ compatible = "mediatek,mt8195-imgsys1_dip_nr", "syscon";
+ reg = <0 0x15130000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_wpe: syscon@15220000 {
+ compatible = "mediatek,mt8195-imgsys1_wpe", "syscon";
+ reg = <0 0x15220000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ ipesys: syscon@15330000 {
+ compatible = "mediatek,mt8195-ipesys", "syscon";
+ reg = <0 0x15330000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys: syscon@16000000 {
+ compatible = "mediatek,mt8195-camsys", "syscon";
+ reg = <0 0x16000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_rawa: syscon@1604f000 {
+ compatible = "mediatek,mt8195-camsys_rawa", "syscon";
+ reg = <0 0x1604f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_yuva: syscon@1606f000 {
+ compatible = "mediatek,mt8195-camsys_yuva", "syscon";
+ reg = <0 0x1606f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_rawb: syscon@1608f000 {
+ compatible = "mediatek,mt8195-camsys_rawb", "syscon";
+ reg = <0 0x1608f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_yuvb: syscon@160af000 {
+ compatible = "mediatek,mt8195-camsys_yuvb", "syscon";
+ reg = <0 0x160af000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_mraw: syscon@16140000 {
+ compatible = "mediatek,mt8195-camsys_mraw", "syscon";
+ reg = <0 0x16140000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ ccusys: syscon@17200000 {
+ compatible = "mediatek,mt8195-ccusys", "syscon";
+ reg = <0 0x17200000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys_soc: syscon@1800f000 {
+ compatible = "mediatek,mt8195-vdecsys_soc", "syscon";
+ reg = <0 0x1800f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys: syscon@1802f000 {
+ compatible = "mediatek,mt8195-vdecsys", "syscon";
+ reg = <0 0x1802f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys_core1: syscon@1803f000 {
+ compatible = "mediatek,mt8195-vdecsys_core1", "syscon";
+ reg = <0 0x1803f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ apusys_pll: syscon@190f3000 {
+ compatible = "mediatek,mt8195-apusys_pll", "syscon";
+ reg = <0 0x190f3000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vencsys: syscon@1a000000 {
+ compatible = "mediatek,mt8195-vencsys", "syscon";
+ reg = <0 0x1a000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vencsys_core1: syscon@1b000000 {
+ compatible = "mediatek,mt8195-vencsys_core1", "syscon";
+ reg = <0 0x1b000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+ };
+};
--
2.14.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile
@ 2021-09-22 9:33 ` Seiya Wang
0 siblings, 0 replies; 9+ messages in thread
From: Seiya Wang @ 2021-09-22 9:33 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring
Cc: linux-arm-kernel, linux-mediatek, devicetree, linux-kernel,
srv_heupstream, Seiya Wang
Add basic chip support for Mediatek MT8195
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 +
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1024 +++++++++++++++++++++++++++
3 files changed, 1054 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..7aa08bb4c078 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -32,4 +32,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
new file mode 100644
index 000000000000..82bb10e9a531
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+/dts-v1/;
+#include "mt8195.dtsi"
+
+/ {
+ model = "MediaTek MT8195 evaluation board";
+ compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
new file mode 100644
index 000000000000..b2ff83882e2e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
@@ -0,0 +1,1024 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/clock/mt8195-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/reset/ti-syscon.h>
+
+/ {
+ compatible = "mediatek,mt8195";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ clk26m: oscillator0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ clk32k: oscillator1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "clk32k";
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x000>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x100>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x200>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x300>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu4: cpu@400 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x400>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu5: cpu@500 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x500>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu6: cpu@600 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x600>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu7: cpu@700 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x700>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ cluster1 {
+ core0 {
+ cpu = <&cpu4>;
+ };
+ core1 {
+ cpu = <&cpu5>;
+ };
+ core2 {
+ cpu = <&cpu6>;
+ };
+ core3 {
+ cpu = <&cpu7>;
+ };
+ };
+ };
+
+ idle-states {
+ entry-method = "arm,psci";
+ cpuoff_l: cpuoff_l {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x00010001>;
+ local-timer-stop;
+ entry-latency-us = <50>;
+ exit-latency-us = <95>;
+ min-residency-us = <580>;
+ };
+ cpuoff_b: cpuoff_b {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x00010001>;
+ local-timer-stop;
+ entry-latency-us = <45>;
+ exit-latency-us = <140>;
+ min-residency-us = <740>;
+ };
+ clusteroff_l: clusteroff_l {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x01010002>;
+ local-timer-stop;
+ entry-latency-us = <55>;
+ exit-latency-us = <155>;
+ min-residency-us = <840>;
+ };
+ clusteroff_b: clusteroff_b {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x01010002>;
+ local-timer-stop;
+ entry-latency-us = <50>;
+ exit-latency-us = <200>;
+ min-residency-us = <1000>;
+ };
+ };
+
+ l2_0: l2-cache0 {
+ compatible = "cache";
+ next-level-cache = <&l3_0>;
+ };
+
+ l2_1: l2-cache1 {
+ compatible = "cache";
+ next-level-cache = <&l3_0>;
+ };
+
+ l3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+
+ dsu-pmu {
+ compatible = "arm,dsu-pmu";
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
+ cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
+ <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+ };
+
+ pmu-a55 {
+ compatible = "arm,cortex-a55-pmu";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
+ };
+
+ pmu-a78 {
+ compatible = "arm,cortex-a78-pmu";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer: timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-frequency = <13000000>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <4>;
+ #redistributor-regions = <1>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c040000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+
+ ppi-partitions {
+ ppi_cluster0: interrupt-partition-0 {
+ affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
+ };
+ ppi_cluster1: interrupt-partition-1 {
+ affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
+ };
+ };
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8195-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg_ao: infracfg_ao@10001000 {
+ compatible = "mediatek,mt8195-infracfg_ao", "syscon", "simple-mfd";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ infracfg_rst: reset-controller {
+ compatible = "ti,syscon-reset";
+ #reset-cells = <1>;
+ ti,reset-bits = <
+ 0x140 18 0x144 18 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x120 1 0x124 1 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x730 1 0x734 1 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x150 5 0x154 5 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ >;
+ };
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8195-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@10005000 {
+ compatible = "mediatek,mt8195-pinctrl";
+ reg = <0 0x10005000 0 0x1000>,
+ <0 0x11d10000 0 0x1000>,
+ <0 0x11d30000 0 0x1000>,
+ <0 0x11d40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11eb0000 0 0x1000>,
+ <0 0x11f40000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
+ "iocfg_br", "iocfg_lm", "iocfg_rb",
+ "iocfg_tl", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 144>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>;
+ #interrupt-cells = <2>;
+
+ pmif_pin: pmif_default_pin {
+ pinmux = <PINMUX_GPIO36__FUNC_RTC32K_CK>,
+ <PINMUX_GPIO40__FUNC_PWRAP_SPI0_CSN>,
+ <PINMUX_GPIO41__FUNC_PWRAP_SPI0_CK>,
+ <PINMUX_GPIO42__FUNC_PWRAP_SPI0_MO>,
+ <PINMUX_GPIO43__FUNC_PWRAP_SPI0_MI>,
+ <PINMUX_GPIO44__FUNC_SPMI_M_SCL>,
+ <PINMUX_GPIO45__FUNC_SPMI_M_SDA>;
+ };
+ };
+
+ watchdog: watchdog@10007000 {
+ compatible = "mediatek,mt8195-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x10007000 0 0x100>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8195-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ systimer: timer@10017000 {
+ compatible = "mediatek,mt8195-timer",
+ "mediatek,mt6765-timer";
+ reg = <0 0x10017000 0 0x1000>;
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_CLK26M_D2>;
+ };
+
+ pwrap: pwrap@10024000 {
+ compatible = "mediatek,mt8195-pwrap", "syscon";
+ reg = <0 0x10024000 0 0x1000>;
+ reg-names = "pwrap";
+ interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
+ <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
+ clock-names = "spi", "wrap";
+ assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmif_pin>;
+ };
+
+ scp_adsp: syscon@10720000 {
+ compatible = "mediatek,mt8195-scp_adsp", "syscon";
+ reg = <0 0x10720000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ uart0: serial@11001100 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001100 0 0x100>;
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART0>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart1: serial@11001200 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001200 0 0x100>;
+ interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART1>;
+ clock-names = "baud", "bus";
+ };
+
+ uart2: serial@11001300 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001300 0 0x100>;
+ interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART2>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart3: serial@11001400 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001400 0 0x100>;
+ interrupts = <GIC_SPI 723 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART3>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart4: serial@11001500 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001500 0 0x100>;
+ interrupts = <GIC_SPI 724 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART4>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart5: serial@11001600 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001600 0 0x100>;
+ interrupts = <GIC_SPI 725 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART5>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ auxadc: auxadc@11002000 {
+ compatible = "mediatek,mt8195-auxadc",
+ "mediatek,mt8173-auxadc";
+ reg = <0 0x11002000 0 0x1000>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_AUXADC>;
+ clock-names = "main";
+ #io-channel-cells = <1>;
+ status = "disabled";
+ };
+
+ pericfg_ao: syscon@11003000 {
+ compatible = "mediatek,mt8195-pericfg_ao", "syscon";
+ reg = <0 0x11003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ spi0: spi@1100a000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi1: spi@11010000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11010000 0 0x100>;
+ interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI1>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi2: spi@11012000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11012000 0 0x100>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI2>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi3: spi@11013000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11013000 0 0x100>;
+ interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI3>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi4: spi@11018000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11018000 0 0x100>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI4>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi5: spi@11019000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11019000 0 0x100>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI5>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spis0: spi@1101d000 {
+ compatible = "mediatek,mt8195-spi-slave";
+ reg = <0 0x1101d000 0 0x100>;
+ interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SPIS0>;
+ clock-names = "spi";
+ assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+ status = "disabled";
+ };
+
+ spis1: spi@1101e000 {
+ compatible = "mediatek,mt8195-spi-slave";
+ reg = <0 0x1101e000 0 0x100>;
+ interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SPIS1>;
+ clock-names = "spi";
+ assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+ status = "disabled";
+ };
+
+ xhci0: xhci@11200000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>,
+ <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u3port0 PHY_TYPE_USB3>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP>,
+ <&topckgen CLK_TOP_SSUSB_XHCI>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SSUSB>,
+ <&infracfg_ao CLK_INFRA_AO_SSUSB_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_REF>,
+ <&apmixedsys CLK_APMIXED_USB1PLL>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck", "mcu_ck";
+ mediatek,syscon-wakeup = <&pericfg 0x400 103>;
+ wakeup-source;
+ status = "disabled";
+ };
+
+ mmc0: mmc@11230000 {
+ compatible = "mediatek,mt8195-mmc",
+ "mediatek,mt8192-mmc";
+ reg = <0 0x11230000 0 0x10000>,
+ <0 0x11f50000 0 0x1000>;
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_MSDC50_0>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC0>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC0_SRC>;
+ clock-names = "source", "hclk", "source_cg";
+ status = "disabled";
+ };
+
+ mmc1: mmc@11240000 {
+ compatible = "mediatek,mt8195-mmc",
+ "mediatek,mt8192-mmc";
+ reg = <0 0x11240000 0 0x1000>,
+ <0 0x11c70000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_MSDC30_1>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC1>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
+ clock-names = "source", "hclk", "source_cg";
+ status = "disabled";
+ };
+
+ xhci1: xhci1@11290000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11290000 0 0x1000>,
+ <0 0x11293e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port1 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_1P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_1P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_1P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P1_REF>,
+ <&apmixedsys CLK_APMIXED_USB1PLL>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck", "mcu_ck";
+ status = "disabled";
+ };
+
+ xhci2: xhci2@112a0000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x112a0000 0 0x1000>,
+ <0 0x112a3e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 533 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_2P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_2P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_2P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_2P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P2_REF>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck";
+ status = "disabled";
+ };
+
+ xhci3: xhci3@112b0000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x112b0000 0 0x1000>,
+ <0 0x112b3e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port3 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_3P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_3P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_3P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_3P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P3_REF>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck";
+ usb2-lpm-disable;
+ status = "disabled";
+ };
+
+ nor_flash: nor@1132c000 {
+ compatible = "mediatek,mt8195-nor",
+ "mediatek,mt8173-nor";
+ reg = <0 0x1132c000 0 0x1000>;
+ interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_SPINOR>,
+ <&pericfg_ao CLK_PERI_AO_FLASHIF_FLASH>,
+ <&pericfg_ao CLK_PERI_AO_FLASHIF_BUS>;
+ clock-names = "spi", "sf", "axi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ u3phy2: t-phy@11c40000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11c40000 0x700>;
+ status = "disabled";
+
+ u2port2: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P2_REF>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ u3phy3: t-phy@11c50000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11c50000 0x700>;
+ status = "disabled";
+
+ u2port3: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P3_REF>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ i2c5: i2c@11d00000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d00000 0 0x1000>,
+ <0 0x10220580 0 0x80>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C5>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@11d01000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d01000 0 0x1000>,
+ <0 0x10220600 0 0x80>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C6>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@11d02000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d02000 0 0x1000>,
+ <0 0x10220680 0 0x80>;
+ interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C7>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ imp_iic_wrap_s: syscon@11d03000 {
+ compatible = "mediatek,mt8195-imp_iic_wrap_s", "syscon";
+ reg = <0 0x11d03000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ i2c0: i2c@11e00000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e00000 0 0x1000>,
+ <0 0x10220080 0 0x80>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C0>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ };
+
+ i2c1: i2c@11e01000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e01000 0 0x1000>,
+ <0 0x10220200 0 0x80>;
+ interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C1>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@11e02000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e02000 0 0x1000>,
+ <0 0x10220380 0 0x80>;
+ interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C2>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@11e03000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e03000 0 0x1000>,
+ <0 0x10220480 0 0x80>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C3>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@11e04000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e04000 0 0x1000>,
+ <0 0x10220500 0 0x80>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C4>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ imp_iic_wrap_w: syscon@11e05000 {
+ compatible = "mediatek,mt8195-imp_iic_wrap_w", "syscon";
+ reg = <0 0x11e05000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ u3phy1: t-phy@11e30000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11e30000 0xe00>;
+ status = "disabled";
+
+ u2port1: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>,
+ <&clk26m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port1: usb-phy@700 {
+ reg = <0x700 0x700>;
+ clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+ <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ u3phy0: t-phy@11e40000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11e40000 0xe00>;
+ status = "disabled";
+
+ u2port0: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_REF>,
+ <&clk26m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port0: usb-phy@700 {
+ reg = <0x700 0x700>;
+ clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+ <&topckgen CLK_TOP_SSUSB_PHY_REF>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ mfgcfg: syscon@13fbf000 {
+ compatible = "mediatek,mt8195-mfgcfg", "syscon";
+ reg = <0 0x13fbf000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vppsys0: syscon@14000000 {
+ compatible = "mediatek,mt8195-vppsys0", "syscon";
+ reg = <0 0x14000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys: syscon@14e00000 {
+ compatible = "mediatek,mt8195-wpesys", "syscon";
+ reg = <0 0x14e00000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys_vpp0: syscon@14e02000 {
+ compatible = "mediatek,mt8195-wpesys_vpp0", "syscon";
+ reg = <0 0x14e02000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys_vpp1: syscon@14e03000 {
+ compatible = "mediatek,mt8195-wpesys_vpp1", "syscon";
+ reg = <0 0x14e03000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vppsys1: syscon@14f00000 {
+ compatible = "mediatek,mt8195-vppsys1", "syscon";
+ reg = <0 0x14f00000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys: syscon@15000000 {
+ compatible = "mediatek,mt8195-imgsys", "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_dip_top: syscon@15110000 {
+ compatible = "mediatek,mt8195-imgsys1_dip_top", "syscon";
+ reg = <0 0x15110000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_dip_nr: syscon@15130000 {
+ compatible = "mediatek,mt8195-imgsys1_dip_nr", "syscon";
+ reg = <0 0x15130000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_wpe: syscon@15220000 {
+ compatible = "mediatek,mt8195-imgsys1_wpe", "syscon";
+ reg = <0 0x15220000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ ipesys: syscon@15330000 {
+ compatible = "mediatek,mt8195-ipesys", "syscon";
+ reg = <0 0x15330000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys: syscon@16000000 {
+ compatible = "mediatek,mt8195-camsys", "syscon";
+ reg = <0 0x16000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_rawa: syscon@1604f000 {
+ compatible = "mediatek,mt8195-camsys_rawa", "syscon";
+ reg = <0 0x1604f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_yuva: syscon@1606f000 {
+ compatible = "mediatek,mt8195-camsys_yuva", "syscon";
+ reg = <0 0x1606f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_rawb: syscon@1608f000 {
+ compatible = "mediatek,mt8195-camsys_rawb", "syscon";
+ reg = <0 0x1608f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_yuvb: syscon@160af000 {
+ compatible = "mediatek,mt8195-camsys_yuvb", "syscon";
+ reg = <0 0x160af000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_mraw: syscon@16140000 {
+ compatible = "mediatek,mt8195-camsys_mraw", "syscon";
+ reg = <0 0x16140000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ ccusys: syscon@17200000 {
+ compatible = "mediatek,mt8195-ccusys", "syscon";
+ reg = <0 0x17200000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys_soc: syscon@1800f000 {
+ compatible = "mediatek,mt8195-vdecsys_soc", "syscon";
+ reg = <0 0x1800f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys: syscon@1802f000 {
+ compatible = "mediatek,mt8195-vdecsys", "syscon";
+ reg = <0 0x1802f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys_core1: syscon@1803f000 {
+ compatible = "mediatek,mt8195-vdecsys_core1", "syscon";
+ reg = <0 0x1803f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ apusys_pll: syscon@190f3000 {
+ compatible = "mediatek,mt8195-apusys_pll", "syscon";
+ reg = <0 0x190f3000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vencsys: syscon@1a000000 {
+ compatible = "mediatek,mt8195-vencsys", "syscon";
+ reg = <0 0x1a000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vencsys_core1: syscon@1b000000 {
+ compatible = "mediatek,mt8195-vencsys_core1", "syscon";
+ reg = <0 0x1b000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+ };
+};
--
2.14.1
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile
@ 2021-09-22 9:33 ` Seiya Wang
0 siblings, 0 replies; 9+ messages in thread
From: Seiya Wang @ 2021-09-22 9:33 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring
Cc: linux-arm-kernel, linux-mediatek, devicetree, linux-kernel,
srv_heupstream, Seiya Wang
Add basic chip support for Mediatek MT8195
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 +
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1024 +++++++++++++++++++++++++++
3 files changed, 1054 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..7aa08bb4c078 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -32,4 +32,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
new file mode 100644
index 000000000000..82bb10e9a531
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+/dts-v1/;
+#include "mt8195.dtsi"
+
+/ {
+ model = "MediaTek MT8195 evaluation board";
+ compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x80000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
new file mode 100644
index 000000000000..b2ff83882e2e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
@@ -0,0 +1,1024 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/clock/mt8195-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/reset/ti-syscon.h>
+
+/ {
+ compatible = "mediatek,mt8195";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ clk26m: oscillator0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ clk32k: oscillator1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "clk32k";
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x000>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x100>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x200>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55", "arm,armv8";
+ reg = <0x300>;
+ enable-method = "psci";
+ clock-frequency = <1701000000>;
+ capacity-dmips-mhz = <578>;
+ cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+ next-level-cache = <&l2_0>;
+ #cooling-cells = <2>;
+ };
+
+ cpu4: cpu@400 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x400>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu5: cpu@500 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x500>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu6: cpu@600 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x600>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu7: cpu@700 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a78", "arm,armv8";
+ reg = <0x700>;
+ enable-method = "psci";
+ clock-frequency = <2171000000>;
+ capacity-dmips-mhz = <1024>;
+ cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+ next-level-cache = <&l2_1>;
+ #cooling-cells = <2>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ cluster1 {
+ core0 {
+ cpu = <&cpu4>;
+ };
+ core1 {
+ cpu = <&cpu5>;
+ };
+ core2 {
+ cpu = <&cpu6>;
+ };
+ core3 {
+ cpu = <&cpu7>;
+ };
+ };
+ };
+
+ idle-states {
+ entry-method = "arm,psci";
+ cpuoff_l: cpuoff_l {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x00010001>;
+ local-timer-stop;
+ entry-latency-us = <50>;
+ exit-latency-us = <95>;
+ min-residency-us = <580>;
+ };
+ cpuoff_b: cpuoff_b {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x00010001>;
+ local-timer-stop;
+ entry-latency-us = <45>;
+ exit-latency-us = <140>;
+ min-residency-us = <740>;
+ };
+ clusteroff_l: clusteroff_l {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x01010002>;
+ local-timer-stop;
+ entry-latency-us = <55>;
+ exit-latency-us = <155>;
+ min-residency-us = <840>;
+ };
+ clusteroff_b: clusteroff_b {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x01010002>;
+ local-timer-stop;
+ entry-latency-us = <50>;
+ exit-latency-us = <200>;
+ min-residency-us = <1000>;
+ };
+ };
+
+ l2_0: l2-cache0 {
+ compatible = "cache";
+ next-level-cache = <&l3_0>;
+ };
+
+ l2_1: l2-cache1 {
+ compatible = "cache";
+ next-level-cache = <&l3_0>;
+ };
+
+ l3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+
+ dsu-pmu {
+ compatible = "arm,dsu-pmu";
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
+ cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
+ <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+ };
+
+ pmu-a55 {
+ compatible = "arm,cortex-a55-pmu";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
+ };
+
+ pmu-a78 {
+ compatible = "arm,cortex-a78-pmu";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer: timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-frequency = <13000000>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <4>;
+ #redistributor-regions = <1>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>,
+ <0 0x0c040000 0 0x200000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+
+ ppi-partitions {
+ ppi_cluster0: interrupt-partition-0 {
+ affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
+ };
+ ppi_cluster1: interrupt-partition-1 {
+ affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
+ };
+ };
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8195-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg_ao: infracfg_ao@10001000 {
+ compatible = "mediatek,mt8195-infracfg_ao", "syscon", "simple-mfd";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ infracfg_rst: reset-controller {
+ compatible = "ti,syscon-reset";
+ #reset-cells = <1>;
+ ti,reset-bits = <
+ 0x140 18 0x144 18 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x120 1 0x124 1 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x730 1 0x734 1 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ 0x150 5 0x154 5 0 0 (ASSERT_SET | DEASSERT_SET | STATUS_NONE)
+ >;
+ };
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8195-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pio: pinctrl@10005000 {
+ compatible = "mediatek,mt8195-pinctrl";
+ reg = <0 0x10005000 0 0x1000>,
+ <0 0x11d10000 0 0x1000>,
+ <0 0x11d30000 0 0x1000>,
+ <0 0x11d40000 0 0x1000>,
+ <0 0x11e20000 0 0x1000>,
+ <0 0x11eb0000 0 0x1000>,
+ <0 0x11f40000 0 0x1000>,
+ <0 0x1000b000 0 0x1000>;
+ reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
+ "iocfg_br", "iocfg_lm", "iocfg_rb",
+ "iocfg_tl", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 144>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>;
+ #interrupt-cells = <2>;
+
+ pmif_pin: pmif_default_pin {
+ pinmux = <PINMUX_GPIO36__FUNC_RTC32K_CK>,
+ <PINMUX_GPIO40__FUNC_PWRAP_SPI0_CSN>,
+ <PINMUX_GPIO41__FUNC_PWRAP_SPI0_CK>,
+ <PINMUX_GPIO42__FUNC_PWRAP_SPI0_MO>,
+ <PINMUX_GPIO43__FUNC_PWRAP_SPI0_MI>,
+ <PINMUX_GPIO44__FUNC_SPMI_M_SCL>,
+ <PINMUX_GPIO45__FUNC_SPMI_M_SDA>;
+ };
+ };
+
+ watchdog: watchdog@10007000 {
+ compatible = "mediatek,mt8195-wdt",
+ "mediatek,mt6589-wdt";
+ reg = <0 0x10007000 0 0x100>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8195-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ systimer: timer@10017000 {
+ compatible = "mediatek,mt8195-timer",
+ "mediatek,mt6765-timer";
+ reg = <0 0x10017000 0 0x1000>;
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_CLK26M_D2>;
+ };
+
+ pwrap: pwrap@10024000 {
+ compatible = "mediatek,mt8195-pwrap", "syscon";
+ reg = <0 0x10024000 0 0x1000>;
+ reg-names = "pwrap";
+ interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
+ <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
+ clock-names = "spi", "wrap";
+ assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmif_pin>;
+ };
+
+ scp_adsp: syscon@10720000 {
+ compatible = "mediatek,mt8195-scp_adsp", "syscon";
+ reg = <0 0x10720000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ uart0: serial@11001100 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001100 0 0x100>;
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART0>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart1: serial@11001200 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001200 0 0x100>;
+ interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART1>;
+ clock-names = "baud", "bus";
+ };
+
+ uart2: serial@11001300 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001300 0 0x100>;
+ interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART2>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart3: serial@11001400 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001400 0 0x100>;
+ interrupts = <GIC_SPI 723 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART3>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart4: serial@11001500 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001500 0 0x100>;
+ interrupts = <GIC_SPI 724 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART4>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart5: serial@11001600 {
+ compatible = "mediatek,mt8195-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11001600 0 0x100>;
+ interrupts = <GIC_SPI 725 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART5>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ auxadc: auxadc@11002000 {
+ compatible = "mediatek,mt8195-auxadc",
+ "mediatek,mt8173-auxadc";
+ reg = <0 0x11002000 0 0x1000>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_AUXADC>;
+ clock-names = "main";
+ #io-channel-cells = <1>;
+ status = "disabled";
+ };
+
+ pericfg_ao: syscon@11003000 {
+ compatible = "mediatek,mt8195-pericfg_ao", "syscon";
+ reg = <0 0x11003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ spi0: spi@1100a000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi1: spi@11010000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11010000 0 0x100>;
+ interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI1>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi2: spi@11012000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11012000 0 0x100>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI2>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi3: spi@11013000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11013000 0 0x100>;
+ interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI3>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi4: spi@11018000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11018000 0 0x100>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI4>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spi5: spi@11019000 {
+ compatible = "mediatek,mt8195-spi",
+ "mediatek,mt6765-spi";
+ reg = <0 0x11019000 0 0x100>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+ <&topckgen CLK_TOP_SPI>,
+ <&infracfg_ao CLK_INFRA_AO_SPI5>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ spis0: spi@1101d000 {
+ compatible = "mediatek,mt8195-spi-slave";
+ reg = <0 0x1101d000 0 0x100>;
+ interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SPIS0>;
+ clock-names = "spi";
+ assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+ status = "disabled";
+ };
+
+ spis1: spi@1101e000 {
+ compatible = "mediatek,mt8195-spi-slave";
+ reg = <0 0x1101e000 0 0x100>;
+ interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SPIS1>;
+ clock-names = "spi";
+ assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+ status = "disabled";
+ };
+
+ xhci0: xhci@11200000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>,
+ <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u3port0 PHY_TYPE_USB3>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP>,
+ <&topckgen CLK_TOP_SSUSB_XHCI>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&infracfg_ao CLK_INFRA_AO_SSUSB>,
+ <&infracfg_ao CLK_INFRA_AO_SSUSB_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_REF>,
+ <&apmixedsys CLK_APMIXED_USB1PLL>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck", "mcu_ck";
+ mediatek,syscon-wakeup = <&pericfg 0x400 103>;
+ wakeup-source;
+ status = "disabled";
+ };
+
+ mmc0: mmc@11230000 {
+ compatible = "mediatek,mt8195-mmc",
+ "mediatek,mt8192-mmc";
+ reg = <0 0x11230000 0 0x10000>,
+ <0 0x11f50000 0 0x1000>;
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_MSDC50_0>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC0>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC0_SRC>;
+ clock-names = "source", "hclk", "source_cg";
+ status = "disabled";
+ };
+
+ mmc1: mmc@11240000 {
+ compatible = "mediatek,mt8195-mmc",
+ "mediatek,mt8192-mmc";
+ reg = <0 0x11240000 0 0x1000>,
+ <0 0x11c70000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_MSDC30_1>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC1>,
+ <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
+ clock-names = "source", "hclk", "source_cg";
+ status = "disabled";
+ };
+
+ xhci1: xhci1@11290000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x11290000 0 0x1000>,
+ <0 0x11293e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port1 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_1P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_1P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_1P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P1_REF>,
+ <&apmixedsys CLK_APMIXED_USB1PLL>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck", "mcu_ck";
+ status = "disabled";
+ };
+
+ xhci2: xhci2@112a0000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x112a0000 0 0x1000>,
+ <0 0x112a3e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 533 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_2P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_2P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_2P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_2P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P2_REF>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck";
+ status = "disabled";
+ };
+
+ xhci3: xhci3@112b0000 {
+ compatible = "mediatek,mt8195-xhci",
+ "mediatek,mtk-xhci";
+ reg = <0 0x112b0000 0 0x1000>,
+ <0 0x112b3e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH 0>;
+ phys = <&u2port3 PHY_TYPE_USB2>;
+ assigned-clocks = <&topckgen CLK_TOP_USB_TOP_3P>,
+ <&topckgen CLK_TOP_SSUSB_XHCI_3P>;
+ assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+ <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+ clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_3P_BUS>,
+ <&pericfg_ao CLK_PERI_AO_SSUSB_3P_XHCI>,
+ <&topckgen CLK_TOP_SSUSB_P3_REF>;
+ clock-names = "sys_ck", "xhci_ck", "ref_ck";
+ usb2-lpm-disable;
+ status = "disabled";
+ };
+
+ nor_flash: nor@1132c000 {
+ compatible = "mediatek,mt8195-nor",
+ "mediatek,mt8173-nor";
+ reg = <0 0x1132c000 0 0x1000>;
+ interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&topckgen CLK_TOP_SPINOR>,
+ <&pericfg_ao CLK_PERI_AO_FLASHIF_FLASH>,
+ <&pericfg_ao CLK_PERI_AO_FLASHIF_BUS>;
+ clock-names = "spi", "sf", "axi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ u3phy2: t-phy@11c40000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11c40000 0x700>;
+ status = "disabled";
+
+ u2port2: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P2_REF>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ u3phy3: t-phy@11c50000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11c50000 0x700>;
+ status = "disabled";
+
+ u2port3: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P3_REF>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ i2c5: i2c@11d00000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d00000 0 0x1000>,
+ <0 0x10220580 0 0x80>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C5>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@11d01000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d01000 0 0x1000>,
+ <0 0x10220600 0 0x80>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C6>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@11d02000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11d02000 0 0x1000>,
+ <0 0x10220680 0 0x80>;
+ interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C7>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ imp_iic_wrap_s: syscon@11d03000 {
+ compatible = "mediatek,mt8195-imp_iic_wrap_s", "syscon";
+ reg = <0 0x11d03000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ i2c0: i2c@11e00000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e00000 0 0x1000>,
+ <0 0x10220080 0 0x80>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C0>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ };
+
+ i2c1: i2c@11e01000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e01000 0 0x1000>,
+ <0 0x10220200 0 0x80>;
+ interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C1>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@11e02000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e02000 0 0x1000>,
+ <0 0x10220380 0 0x80>;
+ interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C2>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@11e03000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e03000 0 0x1000>,
+ <0 0x10220480 0 0x80>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C3>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@11e04000 {
+ compatible = "mediatek,mt8195-i2c",
+ "mediatek,mt8192-i2c";
+ reg = <0 0x11e04000 0 0x1000>,
+ <0 0x10220500 0 0x80>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH 0>;
+ clock-div = <1>;
+ clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C4>,
+ <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+ clock-names = "main", "dma";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ imp_iic_wrap_w: syscon@11e05000 {
+ compatible = "mediatek,mt8195-imp_iic_wrap_w", "syscon";
+ reg = <0 0x11e05000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ u3phy1: t-phy@11e30000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11e30000 0xe00>;
+ status = "disabled";
+
+ u2port1: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>,
+ <&clk26m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port1: usb-phy@700 {
+ reg = <0x700 0x700>;
+ clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+ <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ u3phy0: t-phy@11e40000 {
+ compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x11e40000 0xe00>;
+ status = "disabled";
+
+ u2port0: usb-phy@0 {
+ reg = <0x0 0x700>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_REF>,
+ <&clk26m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port0: usb-phy@700 {
+ reg = <0x700 0x700>;
+ clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+ <&topckgen CLK_TOP_SSUSB_PHY_REF>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+
+ mfgcfg: syscon@13fbf000 {
+ compatible = "mediatek,mt8195-mfgcfg", "syscon";
+ reg = <0 0x13fbf000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vppsys0: syscon@14000000 {
+ compatible = "mediatek,mt8195-vppsys0", "syscon";
+ reg = <0 0x14000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys: syscon@14e00000 {
+ compatible = "mediatek,mt8195-wpesys", "syscon";
+ reg = <0 0x14e00000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys_vpp0: syscon@14e02000 {
+ compatible = "mediatek,mt8195-wpesys_vpp0", "syscon";
+ reg = <0 0x14e02000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ wpesys_vpp1: syscon@14e03000 {
+ compatible = "mediatek,mt8195-wpesys_vpp1", "syscon";
+ reg = <0 0x14e03000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vppsys1: syscon@14f00000 {
+ compatible = "mediatek,mt8195-vppsys1", "syscon";
+ reg = <0 0x14f00000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys: syscon@15000000 {
+ compatible = "mediatek,mt8195-imgsys", "syscon";
+ reg = <0 0x15000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_dip_top: syscon@15110000 {
+ compatible = "mediatek,mt8195-imgsys1_dip_top", "syscon";
+ reg = <0 0x15110000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_dip_nr: syscon@15130000 {
+ compatible = "mediatek,mt8195-imgsys1_dip_nr", "syscon";
+ reg = <0 0x15130000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ imgsys1_wpe: syscon@15220000 {
+ compatible = "mediatek,mt8195-imgsys1_wpe", "syscon";
+ reg = <0 0x15220000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ ipesys: syscon@15330000 {
+ compatible = "mediatek,mt8195-ipesys", "syscon";
+ reg = <0 0x15330000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys: syscon@16000000 {
+ compatible = "mediatek,mt8195-camsys", "syscon";
+ reg = <0 0x16000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_rawa: syscon@1604f000 {
+ compatible = "mediatek,mt8195-camsys_rawa", "syscon";
+ reg = <0 0x1604f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_yuva: syscon@1606f000 {
+ compatible = "mediatek,mt8195-camsys_yuva", "syscon";
+ reg = <0 0x1606f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_rawb: syscon@1608f000 {
+ compatible = "mediatek,mt8195-camsys_rawb", "syscon";
+ reg = <0 0x1608f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_yuvb: syscon@160af000 {
+ compatible = "mediatek,mt8195-camsys_yuvb", "syscon";
+ reg = <0 0x160af000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ camsys_mraw: syscon@16140000 {
+ compatible = "mediatek,mt8195-camsys_mraw", "syscon";
+ reg = <0 0x16140000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ ccusys: syscon@17200000 {
+ compatible = "mediatek,mt8195-ccusys", "syscon";
+ reg = <0 0x17200000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys_soc: syscon@1800f000 {
+ compatible = "mediatek,mt8195-vdecsys_soc", "syscon";
+ reg = <0 0x1800f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys: syscon@1802f000 {
+ compatible = "mediatek,mt8195-vdecsys", "syscon";
+ reg = <0 0x1802f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vdecsys_core1: syscon@1803f000 {
+ compatible = "mediatek,mt8195-vdecsys_core1", "syscon";
+ reg = <0 0x1803f000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ apusys_pll: syscon@190f3000 {
+ compatible = "mediatek,mt8195-apusys_pll", "syscon";
+ reg = <0 0x190f3000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vencsys: syscon@1a000000 {
+ compatible = "mediatek,mt8195-vencsys", "syscon";
+ reg = <0 0x1a000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ vencsys_core1: syscon@1b000000 {
+ compatible = "mediatek,mt8195-vencsys_core1", "syscon";
+ reg = <0 0x1b000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+ };
+};
--
2.14.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile
2021-09-22 9:33 ` Seiya Wang
(?)
@ 2021-09-24 7:45 ` Chen-Yu Tsai
-1 siblings, 0 replies; 9+ messages in thread
From: Chen-Yu Tsai @ 2021-09-24 7:45 UTC (permalink / raw)
To: Seiya Wang
Cc: Matthias Brugger, Rob Herring,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
moderated list:ARM/Mediatek SoC support, Devicetree List, LKML,
srv_heupstream
Hi,
On Wed, Sep 22, 2021 at 5:43 PM Seiya Wang <seiya.wang@mediatek.com> wrote:
>
> Add basic chip support for Mediatek MT8195
>
> Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 +
> arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1024 +++++++++++++++++++++++++++
> 3 files changed, 1054 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 4f68ebed2e31..7aa08bb4c078 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -32,4 +32,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> new file mode 100644
> index 000000000000..82bb10e9a531
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Seiya Wang <seiya.wang@mediatek.com>
> + */
> +/dts-v1/;
> +#include "mt8195.dtsi"
> +
> +/ {
> + model = "MediaTek MT8195 evaluation board";
> + compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
Can you enable anything else? I assume there should at least be some
storage, USB, and PMICs? Even if the hardware isn't publicly available,
it will give us some idea about what is usable, and if and how they hook
up to external components.
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> new file mode 100644
> index 000000000000..b2ff83882e2e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> @@ -0,0 +1,1024 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (c) 2021 MediaTek Inc.
> + * Author: Seiya Wang <seiya.wang@mediatek.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/clock/mt8195-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
> +#include <dt-bindings/reset/ti-syscon.h>
> +
> +/ {
> + compatible = "mediatek,mt8195";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + clocks {
IIRC we have moved away from having a dedicated "clocks" node to group
clock device nodes. Just move the following two device nodes up one
level.
> + clk26m: oscillator0 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "clk26m";
> + };
> +
> + clk32k: oscillator1 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "clk32k";
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x000>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu1: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x100>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu2: cpu@200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x200>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu3: cpu@300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x300>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu4: cpu@400 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x400>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu5: cpu@500 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x500>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu6: cpu@600 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x600>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu7: cpu@700 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x700>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> + core1 {
> + cpu = <&cpu1>;
> + };
> + core2 {
> + cpu = <&cpu2>;
> + };
> + core3 {
> + cpu = <&cpu3>;
> + };
> + };
> + cluster1 {
> + core0 {
> + cpu = <&cpu4>;
> + };
> + core1 {
> + cpu = <&cpu5>;
> + };
> + core2 {
> + cpu = <&cpu6>;
> + };
> + core3 {
> + cpu = <&cpu7>;
> + };
> + };
> + };
> +
> + idle-states {
> + entry-method = "arm,psci";
> + cpuoff_l: cpuoff_l {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x00010001>;
> + local-timer-stop;
> + entry-latency-us = <50>;
> + exit-latency-us = <95>;
> + min-residency-us = <580>;
> + };
> + cpuoff_b: cpuoff_b {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x00010001>;
> + local-timer-stop;
> + entry-latency-us = <45>;
> + exit-latency-us = <140>;
> + min-residency-us = <740>;
> + };
> + clusteroff_l: clusteroff_l {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x01010002>;
> + local-timer-stop;
> + entry-latency-us = <55>;
> + exit-latency-us = <155>;
> + min-residency-us = <840>;
> + };
> + clusteroff_b: clusteroff_b {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x01010002>;
> + local-timer-stop;
> + entry-latency-us = <50>;
> + exit-latency-us = <200>;
> + min-residency-us = <1000>;
> + };
> + };
> +
> + l2_0: l2-cache0 {
> + compatible = "cache";
> + next-level-cache = <&l3_0>;
> + };
> +
> + l2_1: l2-cache1 {
> + compatible = "cache";
> + next-level-cache = <&l3_0>;
> + };
> +
> + l3_0: l3-cache {
> + compatible = "cache";
> + };
> + };
> +
> + dsu-pmu {
> + compatible = "arm,dsu-pmu";
> + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
> + cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
> + <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
> + };
> +
> + pmu-a55 {
> + compatible = "arm,cortex-a55-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
> + };
> +
> + pmu-a78 {
> + compatible = "arm,cortex-a78-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + timer: timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
> + clock-frequency = <13000000>;
> + };
The interrupts for the PMUs and arch timer aren't listed, as the interrupt
table in the datasheet isn't for the GIC, but another interrupt controller
used in low power modes. It does contain mappings to the GIC for most, but
not all interrupts.
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + gic: interrupt-controller@c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <4>;
> + #redistributor-regions = <1>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>,
> + <0 0x0c040000 0 0x200000>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
> +
> + ppi-partitions {
> + ppi_cluster0: interrupt-partition-0 {
> + affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
> + };
> + ppi_cluster1: interrupt-partition-1 {
> + affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
> + };
> + };
> + };
> +
[...]
> + pio: pinctrl@10005000 {
> + compatible = "mediatek,mt8195-pinctrl";
> + reg = <0 0x10005000 0 0x1000>,
> + <0 0x11d10000 0 0x1000>,
> + <0 0x11d30000 0 0x1000>,
> + <0 0x11d40000 0 0x1000>,
> + <0 0x11e20000 0 0x1000>,
> + <0 0x11eb0000 0 0x1000>,
> + <0 0x11f40000 0 0x1000>,
> + <0 0x1000b000 0 0x1000>;
> + reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
> + "iocfg_br", "iocfg_lm", "iocfg_rb",
> + "iocfg_tl", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 144>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>;
If I am reading the datasheet correctly, this interrupt line is listed as
reserved. OTOH there are a bunch of EINT interrupts.
> + #interrupt-cells = <2>;
> +
> + pmif_pin: pmif_default_pin {
> + pinmux = <PINMUX_GPIO36__FUNC_RTC32K_CK>,
> + <PINMUX_GPIO40__FUNC_PWRAP_SPI0_CSN>,
> + <PINMUX_GPIO41__FUNC_PWRAP_SPI0_CK>,
> + <PINMUX_GPIO42__FUNC_PWRAP_SPI0_MO>,
> + <PINMUX_GPIO43__FUNC_PWRAP_SPI0_MI>,
> + <PINMUX_GPIO44__FUNC_SPMI_M_SCL>,
> + <PINMUX_GPIO45__FUNC_SPMI_M_SDA>;
> + };
> + };
> +
> + pwrap: pwrap@10024000 {
> + compatible = "mediatek,mt8195-pwrap", "syscon";
> + reg = <0 0x10024000 0 0x1000>;
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
> + reg-names = "pwrap";
> + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
> + <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
> + clock-names = "spi", "wrap";
> + assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
> + assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmif_pin>;
> + };
[...]
> + mmc1: mmc@11240000 {
> + compatible = "mediatek,mt8195-mmc",
> + "mediatek,mt8192-mmc";
> + reg = <0 0x11240000 0 0x1000>,
> + <0 0x11c70000 0 0x1000>;
> + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&topckgen CLK_TOP_MSDC30_1>,
> + <&infracfg_ao CLK_INFRA_AO_MSDC1>,
> + <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
> + clock-names = "source", "hclk", "source_cg";
> + status = "disabled";
> + };
> +
mmc2 missing?
> + imp_iic_wrap_s: syscon@11d03000 {
> + compatible = "mediatek,mt8195-imp_iic_wrap_s", "syscon";
> + reg = <0 0x11d03000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
> + imp_iic_wrap_w: syscon@11e05000 {
> + compatible = "mediatek,mt8195-imp_iic_wrap_w", "syscon";
> + reg = <0 0x11e05000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
[...]
> + wpesys: syscon@14e00000 {
> + compatible = "mediatek,mt8195-wpesys", "syscon";
> + reg = <0 0x14e00000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + wpesys_vpp0: syscon@14e02000 {
> + compatible = "mediatek,mt8195-wpesys_vpp0", "syscon";
> + reg = <0 0x14e02000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + wpesys_vpp1: syscon@14e03000 {
> + compatible = "mediatek,mt8195-wpesys_vpp1", "syscon";
> + reg = <0 0x14e03000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the wpe related hardware blocks. As such I can't verify the register
region.
[...]
> + vdecsys_soc: syscon@1800f000 {
> + compatible = "mediatek,mt8195-vdecsys_soc", "syscon";
> + reg = <0 0x1800f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys: syscon@1802f000 {
> + compatible = "mediatek,mt8195-vdecsys", "syscon";
> + reg = <0 0x1802f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys_core1: syscon@1803f000 {
> + compatible = "mediatek,mt8195-vdecsys_core1", "syscon";
> + reg = <0 0x1803f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the vdec related hardware blocks. As such I can't verify the register
region.
[...]
> + vencsys: syscon@1a000000 {
> + compatible = "mediatek,mt8195-vencsys", "syscon";
> + reg = <0 0x1a000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vencsys_core1: syscon@1b000000 {
> + compatible = "mediatek,mt8195-vencsys_core1", "syscon";
> + reg = <0 0x1b000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the venc related hardware blocks. As such I can't verify the register
region.
Besides the aforementioned parts, all the memory ranges, interrupt lines,
and clocks seem to be in order.
ChenYu
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile
@ 2021-09-24 7:45 ` Chen-Yu Tsai
0 siblings, 0 replies; 9+ messages in thread
From: Chen-Yu Tsai @ 2021-09-24 7:45 UTC (permalink / raw)
To: Seiya Wang
Cc: Matthias Brugger, Rob Herring,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
moderated list:ARM/Mediatek SoC support, Devicetree List, LKML,
srv_heupstream
Hi,
On Wed, Sep 22, 2021 at 5:43 PM Seiya Wang <seiya.wang@mediatek.com> wrote:
>
> Add basic chip support for Mediatek MT8195
>
> Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 +
> arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1024 +++++++++++++++++++++++++++
> 3 files changed, 1054 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 4f68ebed2e31..7aa08bb4c078 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -32,4 +32,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> new file mode 100644
> index 000000000000..82bb10e9a531
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Seiya Wang <seiya.wang@mediatek.com>
> + */
> +/dts-v1/;
> +#include "mt8195.dtsi"
> +
> +/ {
> + model = "MediaTek MT8195 evaluation board";
> + compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
Can you enable anything else? I assume there should at least be some
storage, USB, and PMICs? Even if the hardware isn't publicly available,
it will give us some idea about what is usable, and if and how they hook
up to external components.
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> new file mode 100644
> index 000000000000..b2ff83882e2e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> @@ -0,0 +1,1024 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (c) 2021 MediaTek Inc.
> + * Author: Seiya Wang <seiya.wang@mediatek.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/clock/mt8195-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
> +#include <dt-bindings/reset/ti-syscon.h>
> +
> +/ {
> + compatible = "mediatek,mt8195";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + clocks {
IIRC we have moved away from having a dedicated "clocks" node to group
clock device nodes. Just move the following two device nodes up one
level.
> + clk26m: oscillator0 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "clk26m";
> + };
> +
> + clk32k: oscillator1 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "clk32k";
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x000>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu1: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x100>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu2: cpu@200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x200>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu3: cpu@300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x300>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu4: cpu@400 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x400>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu5: cpu@500 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x500>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu6: cpu@600 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x600>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu7: cpu@700 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x700>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> + core1 {
> + cpu = <&cpu1>;
> + };
> + core2 {
> + cpu = <&cpu2>;
> + };
> + core3 {
> + cpu = <&cpu3>;
> + };
> + };
> + cluster1 {
> + core0 {
> + cpu = <&cpu4>;
> + };
> + core1 {
> + cpu = <&cpu5>;
> + };
> + core2 {
> + cpu = <&cpu6>;
> + };
> + core3 {
> + cpu = <&cpu7>;
> + };
> + };
> + };
> +
> + idle-states {
> + entry-method = "arm,psci";
> + cpuoff_l: cpuoff_l {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x00010001>;
> + local-timer-stop;
> + entry-latency-us = <50>;
> + exit-latency-us = <95>;
> + min-residency-us = <580>;
> + };
> + cpuoff_b: cpuoff_b {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x00010001>;
> + local-timer-stop;
> + entry-latency-us = <45>;
> + exit-latency-us = <140>;
> + min-residency-us = <740>;
> + };
> + clusteroff_l: clusteroff_l {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x01010002>;
> + local-timer-stop;
> + entry-latency-us = <55>;
> + exit-latency-us = <155>;
> + min-residency-us = <840>;
> + };
> + clusteroff_b: clusteroff_b {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x01010002>;
> + local-timer-stop;
> + entry-latency-us = <50>;
> + exit-latency-us = <200>;
> + min-residency-us = <1000>;
> + };
> + };
> +
> + l2_0: l2-cache0 {
> + compatible = "cache";
> + next-level-cache = <&l3_0>;
> + };
> +
> + l2_1: l2-cache1 {
> + compatible = "cache";
> + next-level-cache = <&l3_0>;
> + };
> +
> + l3_0: l3-cache {
> + compatible = "cache";
> + };
> + };
> +
> + dsu-pmu {
> + compatible = "arm,dsu-pmu";
> + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
> + cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
> + <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
> + };
> +
> + pmu-a55 {
> + compatible = "arm,cortex-a55-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
> + };
> +
> + pmu-a78 {
> + compatible = "arm,cortex-a78-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + timer: timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
> + clock-frequency = <13000000>;
> + };
The interrupts for the PMUs and arch timer aren't listed, as the interrupt
table in the datasheet isn't for the GIC, but another interrupt controller
used in low power modes. It does contain mappings to the GIC for most, but
not all interrupts.
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + gic: interrupt-controller@c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <4>;
> + #redistributor-regions = <1>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>,
> + <0 0x0c040000 0 0x200000>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
> +
> + ppi-partitions {
> + ppi_cluster0: interrupt-partition-0 {
> + affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
> + };
> + ppi_cluster1: interrupt-partition-1 {
> + affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
> + };
> + };
> + };
> +
[...]
> + pio: pinctrl@10005000 {
> + compatible = "mediatek,mt8195-pinctrl";
> + reg = <0 0x10005000 0 0x1000>,
> + <0 0x11d10000 0 0x1000>,
> + <0 0x11d30000 0 0x1000>,
> + <0 0x11d40000 0 0x1000>,
> + <0 0x11e20000 0 0x1000>,
> + <0 0x11eb0000 0 0x1000>,
> + <0 0x11f40000 0 0x1000>,
> + <0 0x1000b000 0 0x1000>;
> + reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
> + "iocfg_br", "iocfg_lm", "iocfg_rb",
> + "iocfg_tl", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 144>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>;
If I am reading the datasheet correctly, this interrupt line is listed as
reserved. OTOH there are a bunch of EINT interrupts.
> + #interrupt-cells = <2>;
> +
> + pmif_pin: pmif_default_pin {
> + pinmux = <PINMUX_GPIO36__FUNC_RTC32K_CK>,
> + <PINMUX_GPIO40__FUNC_PWRAP_SPI0_CSN>,
> + <PINMUX_GPIO41__FUNC_PWRAP_SPI0_CK>,
> + <PINMUX_GPIO42__FUNC_PWRAP_SPI0_MO>,
> + <PINMUX_GPIO43__FUNC_PWRAP_SPI0_MI>,
> + <PINMUX_GPIO44__FUNC_SPMI_M_SCL>,
> + <PINMUX_GPIO45__FUNC_SPMI_M_SDA>;
> + };
> + };
> +
> + pwrap: pwrap@10024000 {
> + compatible = "mediatek,mt8195-pwrap", "syscon";
> + reg = <0 0x10024000 0 0x1000>;
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
> + reg-names = "pwrap";
> + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
> + <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
> + clock-names = "spi", "wrap";
> + assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
> + assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmif_pin>;
> + };
[...]
> + mmc1: mmc@11240000 {
> + compatible = "mediatek,mt8195-mmc",
> + "mediatek,mt8192-mmc";
> + reg = <0 0x11240000 0 0x1000>,
> + <0 0x11c70000 0 0x1000>;
> + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&topckgen CLK_TOP_MSDC30_1>,
> + <&infracfg_ao CLK_INFRA_AO_MSDC1>,
> + <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
> + clock-names = "source", "hclk", "source_cg";
> + status = "disabled";
> + };
> +
mmc2 missing?
> + imp_iic_wrap_s: syscon@11d03000 {
> + compatible = "mediatek,mt8195-imp_iic_wrap_s", "syscon";
> + reg = <0 0x11d03000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
> + imp_iic_wrap_w: syscon@11e05000 {
> + compatible = "mediatek,mt8195-imp_iic_wrap_w", "syscon";
> + reg = <0 0x11e05000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
[...]
> + wpesys: syscon@14e00000 {
> + compatible = "mediatek,mt8195-wpesys", "syscon";
> + reg = <0 0x14e00000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + wpesys_vpp0: syscon@14e02000 {
> + compatible = "mediatek,mt8195-wpesys_vpp0", "syscon";
> + reg = <0 0x14e02000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + wpesys_vpp1: syscon@14e03000 {
> + compatible = "mediatek,mt8195-wpesys_vpp1", "syscon";
> + reg = <0 0x14e03000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the wpe related hardware blocks. As such I can't verify the register
region.
[...]
> + vdecsys_soc: syscon@1800f000 {
> + compatible = "mediatek,mt8195-vdecsys_soc", "syscon";
> + reg = <0 0x1800f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys: syscon@1802f000 {
> + compatible = "mediatek,mt8195-vdecsys", "syscon";
> + reg = <0 0x1802f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys_core1: syscon@1803f000 {
> + compatible = "mediatek,mt8195-vdecsys_core1", "syscon";
> + reg = <0 0x1803f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the vdec related hardware blocks. As such I can't verify the register
region.
[...]
> + vencsys: syscon@1a000000 {
> + compatible = "mediatek,mt8195-vencsys", "syscon";
> + reg = <0 0x1a000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vencsys_core1: syscon@1b000000 {
> + compatible = "mediatek,mt8195-vencsys_core1", "syscon";
> + reg = <0 0x1b000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the venc related hardware blocks. As such I can't verify the register
region.
Besides the aforementioned parts, all the memory ranges, interrupt lines,
and clocks seem to be in order.
ChenYu
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile
@ 2021-09-24 7:45 ` Chen-Yu Tsai
0 siblings, 0 replies; 9+ messages in thread
From: Chen-Yu Tsai @ 2021-09-24 7:45 UTC (permalink / raw)
To: Seiya Wang
Cc: Matthias Brugger, Rob Herring,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
moderated list:ARM/Mediatek SoC support, Devicetree List, LKML,
srv_heupstream
Hi,
On Wed, Sep 22, 2021 at 5:43 PM Seiya Wang <seiya.wang@mediatek.com> wrote:
>
> Add basic chip support for Mediatek MT8195
>
> Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 29 +
> arch/arm64/boot/dts/mediatek/mt8195.dtsi | 1024 +++++++++++++++++++++++++++
> 3 files changed, 1054 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8195.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 4f68ebed2e31..7aa08bb4c078 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -32,4 +32,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> new file mode 100644
> index 000000000000..82bb10e9a531
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Seiya Wang <seiya.wang@mediatek.com>
> + */
> +/dts-v1/;
> +#include "mt8195.dtsi"
> +
> +/ {
> + model = "MediaTek MT8195 evaluation board";
> + compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
Can you enable anything else? I assume there should at least be some
storage, USB, and PMICs? Even if the hardware isn't publicly available,
it will give us some idea about what is usable, and if and how they hook
up to external components.
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> new file mode 100644
> index 000000000000..b2ff83882e2e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
> @@ -0,0 +1,1024 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (c) 2021 MediaTek Inc.
> + * Author: Seiya Wang <seiya.wang@mediatek.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/clock/mt8195-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
> +#include <dt-bindings/reset/ti-syscon.h>
> +
> +/ {
> + compatible = "mediatek,mt8195";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + clocks {
IIRC we have moved away from having a dedicated "clocks" node to group
clock device nodes. Just move the following two device nodes up one
level.
> + clk26m: oscillator0 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "clk26m";
> + };
> +
> + clk32k: oscillator1 {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "clk32k";
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x000>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu1: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x100>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu2: cpu@200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x200>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu3: cpu@300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55", "arm,armv8";
> + reg = <0x300>;
> + enable-method = "psci";
> + clock-frequency = <1701000000>;
> + capacity-dmips-mhz = <578>;
> + cpu-idle-states = <&cpuoff_l &clusteroff_l>;
> + next-level-cache = <&l2_0>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu4: cpu@400 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x400>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu5: cpu@500 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x500>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu6: cpu@600 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x600>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu7: cpu@700 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a78", "arm,armv8";
> + reg = <0x700>;
> + enable-method = "psci";
> + clock-frequency = <2171000000>;
> + capacity-dmips-mhz = <1024>;
> + cpu-idle-states = <&cpuoff_b &clusteroff_b>;
> + next-level-cache = <&l2_1>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> + core1 {
> + cpu = <&cpu1>;
> + };
> + core2 {
> + cpu = <&cpu2>;
> + };
> + core3 {
> + cpu = <&cpu3>;
> + };
> + };
> + cluster1 {
> + core0 {
> + cpu = <&cpu4>;
> + };
> + core1 {
> + cpu = <&cpu5>;
> + };
> + core2 {
> + cpu = <&cpu6>;
> + };
> + core3 {
> + cpu = <&cpu7>;
> + };
> + };
> + };
> +
> + idle-states {
> + entry-method = "arm,psci";
> + cpuoff_l: cpuoff_l {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x00010001>;
> + local-timer-stop;
> + entry-latency-us = <50>;
> + exit-latency-us = <95>;
> + min-residency-us = <580>;
> + };
> + cpuoff_b: cpuoff_b {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x00010001>;
> + local-timer-stop;
> + entry-latency-us = <45>;
> + exit-latency-us = <140>;
> + min-residency-us = <740>;
> + };
> + clusteroff_l: clusteroff_l {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x01010002>;
> + local-timer-stop;
> + entry-latency-us = <55>;
> + exit-latency-us = <155>;
> + min-residency-us = <840>;
> + };
> + clusteroff_b: clusteroff_b {
> + compatible = "arm,idle-state";
> + arm,psci-suspend-param = <0x01010002>;
> + local-timer-stop;
> + entry-latency-us = <50>;
> + exit-latency-us = <200>;
> + min-residency-us = <1000>;
> + };
> + };
> +
> + l2_0: l2-cache0 {
> + compatible = "cache";
> + next-level-cache = <&l3_0>;
> + };
> +
> + l2_1: l2-cache1 {
> + compatible = "cache";
> + next-level-cache = <&l3_0>;
> + };
> +
> + l3_0: l3-cache {
> + compatible = "cache";
> + };
> + };
> +
> + dsu-pmu {
> + compatible = "arm,dsu-pmu";
> + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
> + cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
> + <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
> + };
> +
> + pmu-a55 {
> + compatible = "arm,cortex-a55-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
> + };
> +
> + pmu-a78 {
> + compatible = "arm,cortex-a78-pmu";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + timer: timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
> + clock-frequency = <13000000>;
> + };
The interrupts for the PMUs and arch timer aren't listed, as the interrupt
table in the datasheet isn't for the GIC, but another interrupt controller
used in low power modes. It does contain mappings to the GIC for most, but
not all interrupts.
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + gic: interrupt-controller@c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <4>;
> + #redistributor-regions = <1>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>,
> + <0 0x0c040000 0 0x200000>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
> +
> + ppi-partitions {
> + ppi_cluster0: interrupt-partition-0 {
> + affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
> + };
> + ppi_cluster1: interrupt-partition-1 {
> + affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
> + };
> + };
> + };
> +
[...]
> + pio: pinctrl@10005000 {
> + compatible = "mediatek,mt8195-pinctrl";
> + reg = <0 0x10005000 0 0x1000>,
> + <0 0x11d10000 0 0x1000>,
> + <0 0x11d30000 0 0x1000>,
> + <0 0x11d40000 0 0x1000>,
> + <0 0x11e20000 0 0x1000>,
> + <0 0x11eb0000 0 0x1000>,
> + <0 0x11f40000 0 0x1000>,
> + <0 0x1000b000 0 0x1000>;
> + reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
> + "iocfg_br", "iocfg_lm", "iocfg_rb",
> + "iocfg_tl", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 144>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH 0>;
If I am reading the datasheet correctly, this interrupt line is listed as
reserved. OTOH there are a bunch of EINT interrupts.
> + #interrupt-cells = <2>;
> +
> + pmif_pin: pmif_default_pin {
> + pinmux = <PINMUX_GPIO36__FUNC_RTC32K_CK>,
> + <PINMUX_GPIO40__FUNC_PWRAP_SPI0_CSN>,
> + <PINMUX_GPIO41__FUNC_PWRAP_SPI0_CK>,
> + <PINMUX_GPIO42__FUNC_PWRAP_SPI0_MO>,
> + <PINMUX_GPIO43__FUNC_PWRAP_SPI0_MI>,
> + <PINMUX_GPIO44__FUNC_SPMI_M_SCL>,
> + <PINMUX_GPIO45__FUNC_SPMI_M_SDA>;
> + };
> + };
> +
> + pwrap: pwrap@10024000 {
> + compatible = "mediatek,mt8195-pwrap", "syscon";
> + reg = <0 0x10024000 0 0x1000>;
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
> + reg-names = "pwrap";
> + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
> + <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
> + clock-names = "spi", "wrap";
> + assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
> + assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmif_pin>;
> + };
[...]
> + mmc1: mmc@11240000 {
> + compatible = "mediatek,mt8195-mmc",
> + "mediatek,mt8192-mmc";
> + reg = <0 0x11240000 0 0x1000>,
> + <0 0x11c70000 0 0x1000>;
> + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
> + clocks = <&topckgen CLK_TOP_MSDC30_1>,
> + <&infracfg_ao CLK_INFRA_AO_MSDC1>,
> + <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
> + clock-names = "source", "hclk", "source_cg";
> + status = "disabled";
> + };
> +
mmc2 missing?
> + imp_iic_wrap_s: syscon@11d03000 {
> + compatible = "mediatek,mt8195-imp_iic_wrap_s", "syscon";
> + reg = <0 0x11d03000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
> + imp_iic_wrap_w: syscon@11e05000 {
> + compatible = "mediatek,mt8195-imp_iic_wrap_w", "syscon";
> + reg = <0 0x11e05000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for this hardware block. As such I can't verify the register region.
[...]
> + wpesys: syscon@14e00000 {
> + compatible = "mediatek,mt8195-wpesys", "syscon";
> + reg = <0 0x14e00000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + wpesys_vpp0: syscon@14e02000 {
> + compatible = "mediatek,mt8195-wpesys_vpp0", "syscon";
> + reg = <0 0x14e02000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + wpesys_vpp1: syscon@14e03000 {
> + compatible = "mediatek,mt8195-wpesys_vpp1", "syscon";
> + reg = <0 0x14e03000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the wpe related hardware blocks. As such I can't verify the register
region.
[...]
> + vdecsys_soc: syscon@1800f000 {
> + compatible = "mediatek,mt8195-vdecsys_soc", "syscon";
> + reg = <0 0x1800f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys: syscon@1802f000 {
> + compatible = "mediatek,mt8195-vdecsys", "syscon";
> + reg = <0 0x1802f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vdecsys_core1: syscon@1803f000 {
> + compatible = "mediatek,mt8195-vdecsys_core1", "syscon";
> + reg = <0 0x1803f000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the vdec related hardware blocks. As such I can't verify the register
region.
[...]
> + vencsys: syscon@1a000000 {
> + compatible = "mediatek,mt8195-vencsys", "syscon";
> + reg = <0 0x1a000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + vencsys_core1: syscon@1b000000 {
> + compatible = "mediatek,mt8195-vencsys_core1", "syscon";
> + reg = <0 0x1b000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
The datasheet I have doesn't provide a memory map, nor is there a section
for the venc related hardware blocks. As such I can't verify the register
region.
Besides the aforementioned parts, all the memory ranges, interrupt lines,
and clocks seem to be in order.
ChenYu
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2021-09-24 7:48 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-09-22 9:33 [PATCH v4 0/1] Add basic node support for Mediatek MT8195 SoC Seiya Wang
2021-09-22 9:33 ` Seiya Wang
2021-09-22 9:33 ` Seiya Wang
2021-09-22 9:33 ` [PATCH v4 1/1] arm64: dts: Add Mediatek SoC MT8195 and evaluation board dts and Makefile Seiya Wang
2021-09-22 9:33 ` Seiya Wang
2021-09-22 9:33 ` Seiya Wang
2021-09-24 7:45 ` Chen-Yu Tsai
2021-09-24 7:45 ` Chen-Yu Tsai
2021-09-24 7:45 ` Chen-Yu Tsai
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.