* [PATCH v3 02/17] arm64: dts: qcom: Add SM6350 device tree
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 03/17] arm64: dts: qcom: sm6350: Add LLCC node Konrad Dybcio
` (16 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, Kees Cook, Anton Vorontsov, Colin Cross, Tony Luck,
linux-arm-msm, devicetree, linux-kernel
Add a base DT for SM6350 SoC
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v2:
- Contain all the cpus within one cluster, as this SoC uses ARM's DynamIQ
arch/arm64/boot/dts/qcom/sm6350.dtsi | 485 +++++++++++++++++++++++++++
1 file changed, 485 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm6350.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
new file mode 100644
index 000000000000..d718ecf7d74e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -0,0 +1,485 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+ interrupt-parent = <&intc>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <76800000>;
+ clock-output-names = "xo_board";
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32764>;
+ #clock-cells = <0>;
+ };
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ L3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+ };
+
+ CPU1: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ next-level-cache = <&L2_100>;
+ #cooling-cells = <2>;
+ L2_100: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU2: cpu@200 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x200>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ next-level-cache = <&L2_200>;
+ #cooling-cells = <2>;
+ L2_200: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU3: cpu@300 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x300>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ next-level-cache = <&L2_300>;
+ #cooling-cells = <2>;
+ L2_300: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU4: cpu@400 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x400>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ next-level-cache = <&L2_400>;
+ #cooling-cells = <2>;
+ L2_400: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU5: cpu@500 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x500>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1024>;
+ dynamic-power-coefficient = <100>;
+ next-level-cache = <&L2_500>;
+ #cooling-cells = <2>;
+ L2_500: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+
+ };
+
+ CPU6: cpu@600 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x600>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1894>;
+ dynamic-power-coefficient = <703>;
+ next-level-cache = <&L2_600>;
+ #cooling-cells = <2>;
+ L2_600: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU7: cpu@700 {
+ device_type = "cpu";
+ compatible = "qcom,kryo560";
+ reg = <0x0 0x700>;
+ enable-method = "psci";
+ capacity-dmips-mhz = <1894>;
+ dynamic-power-coefficient = <703>;
+ next-level-cache = <&L2_700>;
+ #cooling-cells = <2>;
+ L2_700: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+
+ core2 {
+ cpu = <&CPU2>;
+ };
+
+ core3 {
+ cpu = <&CPU3>;
+ };
+
+ core4 {
+ cpu = <&CPU4>;
+ };
+
+ core5 {
+ cpu = <&CPU5>;
+ };
+
+ core6 {
+ cpu = <&CPU6>;
+ };
+
+ core7 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-sm6350", "qcom,scm";
+ #reset-cells = <1>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: memory@80000000 {
+ reg = <0 0x80000000 0 0x600000>;
+ no-map;
+ };
+
+ xbl_aop_mem: memory@80700000 {
+ reg = <0 0x80700000 0 0x160000>;
+ no-map;
+ };
+
+ cmd_db: memory@80860000 {
+ compatible = "qcom,cmd-db";
+ reg = <0 0x80860000 0 0x20000>;
+ no-map;
+ };
+
+ sec_apps_mem: memory@808ff000 {
+ reg = <0 0x808ff000 0 0x1000>;
+ no-map;
+ };
+
+ smem_mem: memory@80900000 {
+ reg = <0 0x80900000 0 0x200000>;
+ no-map;
+ };
+
+ cdsp_sec_mem: memory@80b00000 {
+ reg = <0 0x80b00000 0 0x1e00000>;
+ no-map;
+ };
+
+ pil_camera_mem: memory@86000000 {
+ reg = <0 0x86000000 0 0x500000>;
+ no-map;
+ };
+
+ pil_npu_mem: memory@86500000 {
+ reg = <0 0x86500000 0 0x500000>;
+ no-map;
+ };
+
+ pil_video_mem: memory@86a00000 {
+ reg = <0 0x86a00000 0 0x500000>;
+ no-map;
+ };
+
+ pil_cdsp_mem: memory@86f00000 {
+ reg = <0 0x86f00000 0 0x1e00000>;
+ no-map;
+ };
+
+ pil_adsp_mem: memory@88d00000 {
+ reg = <0 0x88d00000 0 0x2800000>;
+ no-map;
+ };
+
+ wlan_fw_mem: memory@8b500000 {
+ reg = <0 0x8b500000 0 0x200000>;
+ no-map;
+ };
+
+ pil_ipa_fw_mem: memory@8b700000 {
+ reg = <0 0x8b700000 0 0x10000>;
+ no-map;
+ };
+
+ pil_ipa_gsi_mem: memory@8b710000 {
+ reg = <0 0x8b710000 0 0x5400>;
+ no-map;
+ };
+
+ pil_gpu_mem: memory@8b715400 {
+ reg = <0 0x8b715400 0 0x2000>;
+ no-map;
+ };
+
+ pil_modem_mem: memory@8b800000 {
+ reg = <0 0x8b800000 0 0xf800000>;
+ no-map;
+ };
+
+ cont_splash_memory: memory@a0000000 {
+ reg = <0 0xa0000000 0 0x2300000>;
+ no-map;
+ };
+
+ dfps_data_memory: memory@a2300000 {
+ reg = <0 0xa2300000 0 0x100000>;
+ no-map;
+ };
+
+ removed_region: memory@c0000000 {
+ reg = <0 0xc0000000 0 0x3900000>;
+ no-map;
+ };
+
+ debug_region: memory@ffb00000 {
+ reg = <0 0xffb00000 0 0xc0000>;
+ no-map;
+ };
+
+ last_log_region: memory@ffbc0000 {
+ reg = <0 0xffbc0000 0 0x40000>;
+ no-map;
+ };
+
+ ramoops: ramoops@ffc00000 {
+ compatible = "removed-dma-pool", "ramoops";
+ reg = <0 0xffc00000 0 0x00100000>;
+ record-size = <0x1000>;
+ console-size = <0x40000>;
+ ftrace-size = <0x0>;
+ msg-size = <0x20000 0x20000>;
+ cc-size = <0x0>;
+ no-map;
+ };
+
+ cmdline_region: memory@ffd00000 {
+ reg = <0 0xffd00000 0 0x1000>;
+ no-map;
+ };
+ };
+
+ smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_mem>;
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
+ soc: soc@0 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+ compatible = "simple-bus";
+
+ ipcc: mailbox@408000 {
+ compatible = "qcom,sm6350-ipcc", "qcom,ipcc";
+ reg = <0 0x00408000 0 0x1000>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #mbox-cells = <2>;
+ };
+
+ tcsr_mutex: hwlock@1f40000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x0 0x01f40000 0x0 0x40000>;
+ #hwlock-cells = <1>;
+ };
+
+ pdc: interrupt-controller@b220000 {
+ compatible = "qcom,sm6350-pdc", "qcom,pdc";
+ reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
+ qcom,pdc-ranges = <0 480 94>, <94 609 31>,
+ <125 63 1>, <126 655 12>, <138 139 15>;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&intc>;
+ interrupt-controller;
+ };
+
+ intc: interrupt-controller@17a00000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */
+ <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */
+ interrupts = <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ watchdog@17c10000 {
+ compatible = "qcom,apss-wdt-sm6350", "qcom,kpss-wdt";
+ reg = <0 0x17c10000 0 0x1000>;
+ clocks = <&sleep_clk>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer@17c20000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0 0x17c20000 0x0 0x1000>;
+ clock-frequency = <19200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ frame@17c21000 {
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c21000 0x0 0x1000>,
+ <0x0 0x17c22000 0x0 0x1000>;
+ };
+
+ frame@17c23000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c23000 0x0 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c25000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c25000 0x0 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c27000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c27000 0x0 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c29000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c29000 0x0 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c2b000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c2b000 0x0 0x1000>;
+ status = "disabled";
+ };
+
+ frame@17c2d000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x17c2d000 0x0 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ apps_rsc: rsc@18200000 {
+ compatible = "qcom,rpmh-rsc";
+ label = "apps_rsc";
+ reg = <0x0 0x18200000 0x0 0x10000>,
+ <0x0 0x18210000 0x0 0x10000>,
+ <0x0 0x18220000 0x0 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
+ <WAKE_TCS 3>, <CONTROL_TCS 1>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ clock-frequency = <19200000>;
+ interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 03/17] arm64: dts: qcom: sm6350: Add LLCC node
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 02/17] arm64: dts: qcom: Add SM6350 device tree Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 04/17] arm64: dts: qcom: sm6350: Add RPMHCC node Konrad Dybcio
` (15 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add a node for LLCC with SM6350-specific compatible.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index d718ecf7d74e..5442c088cf37 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -372,6 +372,12 @@ tcsr_mutex: hwlock@1f40000 {
#hwlock-cells = <1>;
};
+ system-cache-controller@9200000 {
+ compatible = "qcom,sm6350-llcc";
+ reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
+ reg-names = "llcc_base", "llcc_broadcast_base";
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm6350-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 04/17] arm64: dts: qcom: sm6350: Add RPMHCC node
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 02/17] arm64: dts: qcom: Add SM6350 device tree Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 03/17] arm64: dts: qcom: sm6350: Add LLCC node Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 05/17] arm64: dts: qcom: sm6350: Add GCC node Konrad Dybcio
` (14 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add RPMHCC node to allow for referencing RPMH-controlled clocks in other
nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 5442c088cf37..555ae0bbba18 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -477,6 +477,13 @@ apps_rsc: rsc@18200000 {
qcom,drv-id = <2>;
qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
<WAKE_TCS 3>, <CONTROL_TCS 1>;
+
+ rpmhcc: clock-controller {
+ compatible = "qcom,sm6350-rpmh-clk";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
};
};
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 05/17] arm64: dts: qcom: sm6350: Add GCC node
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (2 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 04/17] arm64: dts: qcom: sm6350: Add RPMHCC node Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 06/17] arm64: dts: qcom: sm6350: Add TLMM block node Konrad Dybcio
` (13 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add and configure GCC node to allow for referencing GCC-controlled clocks
in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 555ae0bbba18..9934ecec1bb2 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -3,6 +3,8 @@
* Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
*/
+#include <dt-bindings/clock/qcom,gcc-sm6350.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
@@ -357,6 +359,20 @@ soc: soc@0 {
dma-ranges = <0 0 0 0 0x10 0>;
compatible = "simple-bus";
+ gcc: clock-controller@100000 {
+ compatible = "qcom,gcc-sm6350";
+ reg = <0 0x00100000 0 0x1f0000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ clock-names = "bi_tcxo",
+ "bi_tcxo_ao",
+ "sleep_clk";
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&rpmhcc RPMH_CXO_CLK_A>,
+ <&sleep_clk>;
+ };
+
ipcc: mailbox@408000 {
compatible = "qcom,sm6350-ipcc", "qcom,ipcc";
reg = <0 0x00408000 0 0x1000>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 06/17] arm64: dts: qcom: sm6350: Add TLMM block node
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (3 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 05/17] arm64: dts: qcom: sm6350: Add GCC node Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 07/17] arm64: dts: qcom: sm6350: Add USB1 nodes Konrad Dybcio
` (12 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 9934ecec1bb2..68de0beb9b01 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -404,6 +404,25 @@ pdc: interrupt-controller@b220000 {
interrupt-controller;
};
+ tlmm: pinctrl@f100000 {
+ compatible = "qcom,sm6350-tlmm";
+ reg = <0 0x0f100000 0 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 157>;
+ };
+
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 07/17] arm64: dts: qcom: sm6350: Add USB1 nodes
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (4 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 06/17] arm64: dts: qcom: sm6350: Add TLMM block node Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 08/17] arm64: dts: qcom: sm6350: Add cpufreq-hw support Konrad Dybcio
` (11 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add nodes required for USB1 to function. SM6350 (thankfully) resuses SDM845 and
SC7180 IP, so no additional code porting is required.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 101 +++++++++++++++++++++++++++
1 file changed, 101 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 68de0beb9b01..ad755a16310a 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -388,12 +388,113 @@ tcsr_mutex: hwlock@1f40000 {
#hwlock-cells = <1>;
};
+ usb_1_hsphy: phy@88e3000 {
+ compatible = "qcom,sm6350-qusb2-phy", "qcom,qusb2-v2-phy";
+ reg = <0 0x088e3000 0 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&xo_board>, <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ };
+
+ usb_1_qmpphy: phy@88e9000 {
+ compatible = "qcom,sc7180-qmp-usb3-dp-phy";
+ reg = <0 0x088e9000 0 0x200>,
+ <0 0x088e8000 0 0x40>,
+ <0 0x088ea000 0 0x200>;
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&rpmhcc RPMH_QLINK_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+ <&xo_board>;
+ clock-names = "aux", "ref", "com_aux", "cfg_ahb";
+
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
+ reset-names = "phy", "common";
+
+ usb_1_ssphy: usb3-phy@88e9200 {
+ reg = <0 0x088e9200 0 0x200>,
+ <0 0x088e9400 0 0x200>,
+ <0 0x088e9c00 0 0x400>,
+ <0 0x088e9600 0 0x200>,
+ <0 0x088e9800 0 0x200>,
+ <0 0x088e9a00 0 0x100>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+
+ dp_phy: dp-phy@88ea200 {
+ reg = <0 0x088ea200 0 0x200>,
+ <0 0x088ea400 0 0x200>,
+ <0 0x088eac00 0 0x400>,
+ <0 0x088ea600 0 0x200>,
+ <0 0x088ea800 0 0x200>,
+ <0 0x088eaa00 0 0x100>;
+ #phy-cells = <0>;
+ #clock-cells = <1>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+ };
+
system-cache-controller@9200000 {
compatible = "qcom,sm6350-llcc";
reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
reg-names = "llcc_base", "llcc_broadcast_base";
};
+ usb_1: usb@a6f8800 {
+ compatible = "qcom,sm6350-dwc3", "qcom,dwc3";
+ reg = <0 0x0a6f8800 0 0x400>;
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+ <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+ <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+ <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
+ "dm_hs_phy_irq", "ss_phy_irq";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ usb_1_dwc3: dwc3@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a600000 0 0xcd00>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ snps,has-lpm-erratum;
+ snps,hird-threshold = /bits/ 8 <0x10>;
+ phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm6350-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 08/17] arm64: dts: qcom: sm6350: Add cpufreq-hw support
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (5 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 07/17] arm64: dts: qcom: sm6350: Add USB1 nodes Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 09/17] arm64: dts: qcom: sm6350: Add TSENS nodes Konrad Dybcio
` (10 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add cpufreq-hw node and assign qcom,freq-domain properties to CPUs to enable
CPU clock scaling.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index ad755a16310a..582915d2b4f0 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -42,6 +42,7 @@ CPU0: cpu@0 {
capacity-dmips-mhz = <1024>;
dynamic-power-coefficient = <100>;
next-level-cache = <&L2_0>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_0: l2-cache {
compatible = "cache";
@@ -60,6 +61,7 @@ CPU1: cpu@100 {
capacity-dmips-mhz = <1024>;
dynamic-power-coefficient = <100>;
next-level-cache = <&L2_100>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_100: l2-cache {
compatible = "cache";
@@ -75,6 +77,7 @@ CPU2: cpu@200 {
capacity-dmips-mhz = <1024>;
dynamic-power-coefficient = <100>;
next-level-cache = <&L2_200>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_200: l2-cache {
compatible = "cache";
@@ -90,6 +93,7 @@ CPU3: cpu@300 {
capacity-dmips-mhz = <1024>;
dynamic-power-coefficient = <100>;
next-level-cache = <&L2_300>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_300: l2-cache {
compatible = "cache";
@@ -105,6 +109,7 @@ CPU4: cpu@400 {
capacity-dmips-mhz = <1024>;
dynamic-power-coefficient = <100>;
next-level-cache = <&L2_400>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_400: l2-cache {
compatible = "cache";
@@ -120,6 +125,7 @@ CPU5: cpu@500 {
capacity-dmips-mhz = <1024>;
dynamic-power-coefficient = <100>;
next-level-cache = <&L2_500>;
+ qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_500: l2-cache {
compatible = "cache";
@@ -136,6 +142,7 @@ CPU6: cpu@600 {
capacity-dmips-mhz = <1894>;
dynamic-power-coefficient = <703>;
next-level-cache = <&L2_600>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
#cooling-cells = <2>;
L2_600: l2-cache {
compatible = "cache";
@@ -151,6 +158,7 @@ CPU7: cpu@700 {
capacity-dmips-mhz = <1894>;
dynamic-power-coefficient = <703>;
next-level-cache = <&L2_700>;
+ qcom,freq-domain = <&cpufreq_hw 1>;
#cooling-cells = <2>;
L2_700: l2-cache {
compatible = "cache";
@@ -621,6 +629,16 @@ rpmhcc: clock-controller {
clocks = <&xo_board>;
};
};
+
+ cpufreq_hw: cpufreq@18323000 {
+ compatible = "qcom,cpufreq-hw";
+ reg = <0 0x18323000 0 0x1000>, <0 0x18325800 0 0x1000>;
+ reg-names = "freq-domain0", "freq-domain1";
+ clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
+ clock-names = "xo", "alternate";
+
+ #freq-domain-cells = <1>;
+ };
};
timer {
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 09/17] arm64: dts: qcom: sm6350: Add TSENS nodes
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (6 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 08/17] arm64: dts: qcom: sm6350: Add cpufreq-hw support Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 10/17] arm64: dts: qcom: sm6350: Add AOSS_QMP Konrad Dybcio
` (9 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add nodes required for TSENS block using the common qcom,tsens-v2 binding.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 582915d2b4f0..2e9701f2f276 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -513,6 +513,28 @@ pdc: interrupt-controller@b220000 {
interrupt-controller;
};
+ tsens0: thermal-sensor@c263000 {
+ compatible = "qcom,sm6350-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c263000 0 0x1ff>, /* TM */
+ <0 0x0c222000 0 0x8>; /* SROT */
+ #qcom,sensors = <16>;
+ interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+ <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
+ tsens1: thermal-sensor@c265000 {
+ compatible = "qcom,sm6350-tsens", "qcom,tsens-v2";
+ reg = <0 0x0c265000 0 0x1ff>, /* TM */
+ <0 0x0c223000 0 0x8>; /* SROT */
+ #qcom,sensors = <16>;
+ interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+ <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow", "critical";
+ #thermal-sensor-cells = <1>;
+ };
+
tlmm: pinctrl@f100000 {
compatible = "qcom,sm6350-tlmm";
reg = <0 0x0f100000 0 0x300000>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 10/17] arm64: dts: qcom: sm6350: Add AOSS_QMP
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (7 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 09/17] arm64: dts: qcom: sm6350: Add TSENS nodes Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 11/17] arm64: dts: qcom: sm6350: Add SPMI bus Konrad Dybcio
` (8 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add a node for AOSS_QMP in preparation for remote processor enablement.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 2e9701f2f276..c2c5cc30307b 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -535,6 +535,17 @@ tsens1: thermal-sensor@c265000 {
#thermal-sensor-cells = <1>;
};
+ aoss_qmp: power-controller@c300000 {
+ compatible = "qcom,sm6350-aoss-qmp", "qcom,aoss-qmp";
+ reg = <0 0x0c300000 0 0x1000>;
+ interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+ IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+ #clock-cells = <0>;
+ #power-domain-cells = <1>;
+ };
+
tlmm: pinctrl@f100000 {
compatible = "qcom,sm6350-tlmm";
reg = <0 0x0f100000 0 0x300000>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 11/17] arm64: dts: qcom: sm6350: Add SPMI bus
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (8 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 10/17] arm64: dts: qcom: sm6350: Add AOSS_QMP Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 12/17] arm64: dts: qcom: sm6350: Add PRNG node Konrad Dybcio
` (7 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add a node for SPMI to allow for communication with on-board PMICs.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index c2c5cc30307b..0c50a8f9414c 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -546,6 +546,24 @@ aoss_qmp: power-controller@c300000 {
#power-domain-cells = <1>;
};
+ spmi_bus: spmi@c440000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0 0xc440000 0 0x1100>,
+ <0 0xc600000 0 0x2000000>,
+ <0 0xe600000 0 0x100000>,
+ <0 0xe700000 0 0xa0000>,
+ <0 0xc40a000 0 0x26000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
tlmm: pinctrl@f100000 {
compatible = "qcom,sm6350-tlmm";
reg = <0 0x0f100000 0 0x300000>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 12/17] arm64: dts: qcom: sm6350: Add PRNG node
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (9 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 11/17] arm64: dts: qcom: sm6350: Add SPMI bus Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:21 ` [PATCH v3 13/17] arm64: dts: qcom: sm6350: Add RPMHPD and BCM voter Konrad Dybcio
` (6 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add a node for the PRNG to enable hw-accelerated pseudo-random number
generation.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 0c50a8f9414c..0765ae4fb5ea 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -390,6 +390,13 @@ ipcc: mailbox@408000 {
#mbox-cells = <2>;
};
+ rng: rng@793000 {
+ compatible = "qcom,prng-ee";
+ reg = <0 0x00793000 0 0x1000>;
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "core";
+ };
+
tcsr_mutex: hwlock@1f40000 {
compatible = "qcom,tcsr-mutex";
reg = <0x0 0x01f40000 0x0 0x40000>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 13/17] arm64: dts: qcom: sm6350: Add RPMHPD and BCM voter
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (10 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 12/17] arm64: dts: qcom: sm6350: Add PRNG node Konrad Dybcio
@ 2021-09-23 16:21 ` Konrad Dybcio
2021-09-23 16:22 ` [PATCH v3 14/17] arm64: dts: qcom: sm6350: Add SDHCI1/2 nodes Konrad Dybcio
` (5 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:21 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add RPMHPD node, its OPP table and BCM voter to prepare for performance level
voting.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 54 ++++++++++++++++++++++++++++
1 file changed, 54 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 0765ae4fb5ea..6162af01ae9a 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -686,6 +686,60 @@ rpmhcc: clock-controller {
clock-names = "xo";
clocks = <&xo_board>;
};
+
+ rpmhpd: power-controller {
+ compatible = "qcom,sm6350-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmhpd_opp_ret: opp1 {
+ opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
+ };
+
+ apps_bcm_voter: bcm_voter {
+ compatible = "qcom,bcm-voter";
+ };
};
cpufreq_hw: cpufreq@18323000 {
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 14/17] arm64: dts: qcom: sm6350: Add SDHCI1/2 nodes
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (11 preceding siblings ...)
2021-09-23 16:21 ` [PATCH v3 13/17] arm64: dts: qcom: sm6350: Add RPMHPD and BCM voter Konrad Dybcio
@ 2021-09-23 16:22 ` Konrad Dybcio
2021-09-23 16:22 ` [PATCH v3 15/17] arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1 Konrad Dybcio
` (4 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:22 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add SDHCI1/2 nodes for eMMC and uSD card respectively.
Do note that most SM6350 devices seem to come with UFS.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 81 ++++++++++++++++++++++++++++
1 file changed, 81 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 6162af01ae9a..3699176d2575 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
/ {
@@ -397,12 +398,92 @@ rng: rng@793000 {
clock-names = "core";
};
+ sdhc_1: sdhci@7c4000 {
+ compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x007c4000 0 0x1000>,
+ <0 0x007c5000 0 0x1000>,
+ <0 0x007c8000 0 0x8000>;
+ reg-names = "hc", "cqhci", "ice";
+
+ interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "core", "xo";
+ qcom,dll-config = <0x000f642c>;
+ qcom,ddr-config = <0x80040868>;
+ power-domains = <&rpmhpd SM6350_CX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
+ bus-width = <8>;
+ non-removable;
+ supports-cqe;
+
+ status = "disabled";
+
+ sdhc1_opp_table: sdhc1-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ required-opps = <&rpmhpd_opp_min_svs>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
tcsr_mutex: hwlock@1f40000 {
compatible = "qcom,tcsr-mutex";
reg = <0x0 0x01f40000 0x0 0x40000>;
#hwlock-cells = <1>;
};
+ sdhc_2: sdhci@8804000 {
+ compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x08804000 0 0x1000>;
+
+ interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "core", "xo";
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+ power-domains = <&rpmhpd SM6350_CX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+ bus-width = <4>;
+
+ status = "disabled";
+
+ sdhc2_opp_table: sdhc2-opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-202000000 {
+ opp-hz = /bits/ 64 <202000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
usb_1_hsphy: phy@88e3000 {
compatible = "qcom,sm6350-qusb2-phy", "qcom,qusb2-v2-phy";
reg = <0 0x088e3000 0 0x400>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 15/17] arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (12 preceding siblings ...)
2021-09-23 16:22 ` [PATCH v3 14/17] arm64: dts: qcom: sm6350: Add SDHCI1/2 nodes Konrad Dybcio
@ 2021-09-23 16:22 ` Konrad Dybcio
2021-09-23 16:22 ` [PATCH v3 16/17] arm64: dts: qcom: Add device tree for Sony Xperia 10 III Konrad Dybcio
` (3 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:22 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add a node for the APPS SMMU to allow for managing memory access to peripherals
such as the USB controller.
While at it, add iommus property to the USB1 node to make sure its registers can
be accessed, as they seem to be gated by default.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v2:
- Squash the usb oneliner into this patch
arch/arm64/boot/dts/qcom/sm6350.dtsi | 89 ++++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 3699176d2575..dc7c54ee0264 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -582,6 +582,7 @@ usb_1_dwc3: dwc3@a600000 {
compatible = "snps,dwc3";
reg = <0 0x0a600000 0 0xcd00>;
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x540 0x0>;
snps,dis_u2_susphy_quirk;
snps,dis_enblslpm_quirk;
snps,has-lpm-erratum;
@@ -671,6 +672,94 @@ tlmm: pinctrl@f100000 {
gpio-ranges = <&tlmm 0 0 157>;
};
+ apps_smmu: iommu@15000000 {
+ compatible = "qcom,sm6350-smmu-500", "arm,mmu-500";
+ reg = <0 0x15000000 0 0x100000>;
+ #iommu-cells = <2>;
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 16/17] arm64: dts: qcom: Add device tree for Sony Xperia 10 III
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (13 preceding siblings ...)
2021-09-23 16:22 ` [PATCH v3 15/17] arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1 Konrad Dybcio
@ 2021-09-23 16:22 ` Konrad Dybcio
2021-09-23 16:22 ` [PATCH v3 17/17] arm64: dts: qcom: pm6150l: Add missing include Konrad Dybcio
` (2 subsequent siblings)
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:22 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
trees. There is no sign of another Lena devices on the horizon, so a common
DTSI is not created for now. 10 III features a Full HD OLED display and 5G
support, among other nice things like USB3.
The bootloader is VERY unpleasant, to get a bootable setup you have to run:
mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
--dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
--cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
--os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
--header_version 2 -o mainline.img
adb reboot bootloader
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img
fastboot flash boot mainline.img
fastboot erase dtbo // This will take approx 70s...
fastboot reboot
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../qcom/sm6350-sony-xperia-lena-pdx213.dts | 57 +++++++++++++++++++
2 files changed, 58 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70516508be56..59ece83abad0 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -84,6 +84,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm6350-sony-xperia-lena-pdx213.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-microsoft-surface-duo.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
new file mode 100644
index 000000000000..a26c23754f5d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+/dts-v1/;
+
+#include "sm6350.dtsi"
+
+/ {
+ model = "Sony Xperia 10 III";
+ compatible = "sony,pdx213", "qcom,sm6350";
+ qcom,msm-id = <434 0x10000>, <459 0x10000>;
+ qcom,board-id = <0x1000B 0>;
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer: framebuffer@a0000000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0xa0000000 0 0x2300000>;
+ width = <1080>;
+ height = <2520>;
+ stride = <(1080 * 4)>;
+ format = "a8r8g8b8";
+ clocks = <&gcc GCC_DISP_AXI_CLK>;
+ };
+ };
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ cd-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <13 4>, <45 2>, <56 2>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ maximum-speed = "super-speed";
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+};
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH v3 17/17] arm64: dts: qcom: pm6150l: Add missing include
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (14 preceding siblings ...)
2021-09-23 16:22 ` [PATCH v3 16/17] arm64: dts: qcom: Add device tree for Sony Xperia 10 III Konrad Dybcio
@ 2021-09-23 16:22 ` Konrad Dybcio
2021-09-23 16:50 ` [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Rob Herring
2021-09-27 22:56 ` Bjorn Andersson
17 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:22 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add missing include to make it compile.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/pm6150l.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/qcom/pm6150l.dtsi b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
index b49860cd1387..3ca2860bb0cf 100644
--- a/arch/arm64/boot/dts/qcom/pm6150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
@@ -1,6 +1,7 @@
// SPDX-License-Identifier: BSD-3-Clause
// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
--
2.33.0
^ permalink raw reply related [flat|nested] 20+ messages in thread* Re: [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (15 preceding siblings ...)
2021-09-23 16:22 ` [PATCH v3 17/17] arm64: dts: qcom: pm6150l: Add missing include Konrad Dybcio
@ 2021-09-23 16:50 ` Rob Herring
2021-09-23 16:51 ` Konrad Dybcio
2021-09-27 22:56 ` Bjorn Andersson
17 siblings, 1 reply; 20+ messages in thread
From: Rob Herring @ 2021-09-23 16:50 UTC (permalink / raw)
To: Konrad Dybcio
Cc: Guenter Roeck, jamipkettunen, Hector Martin, Sudeep Holla,
angelogioacchino.delregno, devicetree, Vinod Koul,
Sebastian Reichel, linux-kernel, martin.botka, Lorenzo Pieralisi,
Rob Herring, ~postmarketos/upstreaming, marijn.suijten,
Mark Brown, Srinivas Kandagatla
On Thu, 23 Sep 2021 18:21:47 +0200, Konrad Dybcio wrote:
> Document Kryo 560 CPUs found in Qualcomm Snapdragon 690 (SM6350).
>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> ---
> Documentation/devicetree/bindings/arm/cpus.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Please add Acked-by/Reviewed-by tags when posting new versions. However,
there's no need to repost patches *only* to add the tags. The upstream
maintainer will do that for acks received on the version they apply.
If a tag was not added on purpose, please state why and what changed.
^ permalink raw reply [flat|nested] 20+ messages in thread* Re: [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs
2021-09-23 16:50 ` [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Rob Herring
@ 2021-09-23 16:51 ` Konrad Dybcio
0 siblings, 0 replies; 20+ messages in thread
From: Konrad Dybcio @ 2021-09-23 16:51 UTC (permalink / raw)
To: Rob Herring
Cc: Guenter Roeck, jamipkettunen, Hector Martin, Sudeep Holla,
angelogioacchino.delregno, devicetree, Vinod Koul,
Sebastian Reichel, linux-kernel, martin.botka, Lorenzo Pieralisi,
Rob Herring, ~postmarketos/upstreaming, marijn.suijten,
Mark Brown, Srinivas Kandagatla
On 23.09.2021 18:50, Rob Herring wrote:
> On Thu, 23 Sep 2021 18:21:47 +0200, Konrad Dybcio wrote:
>> Document Kryo 560 CPUs found in Qualcomm Snapdragon 690 (SM6350).
>>
>> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
>> ---
>> Documentation/devicetree/bindings/arm/cpus.yaml | 1 +
>> 1 file changed, 1 insertion(+)
>>
>
> Please add Acked-by/Reviewed-by tags when posting new versions. However,
> there's no need to repost patches *only* to add the tags. The upstream
> maintainer will do that for acks received on the version they apply.
>
> If a tag was not added on purpose, please state why and what changed.
>
It was an overlook from my side. Totally didn't mean to skip the acks/r-bs.
Apologies for the inconvenience caused.
Konrad
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs
2021-09-23 16:21 [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Konrad Dybcio
` (16 preceding siblings ...)
2021-09-23 16:50 ` [PATCH v3 01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs Rob Herring
@ 2021-09-27 22:56 ` Bjorn Andersson
17 siblings, 0 replies; 20+ messages in thread
From: Bjorn Andersson @ 2021-09-27 22:56 UTC (permalink / raw)
To: ~postmarketos/upstreaming, Konrad Dybcio
Cc: linux-kernel, Srinivas Kandagatla, marijn.suijten, Hector Martin,
martin.botka, Rob Herring, Mark Brown, Sebastian Reichel,
Vinod Koul, Sudeep Holla, Lorenzo Pieralisi,
angelogioacchino.delregno, Guenter Roeck, devicetree,
jamipkettunen
On Thu, 23 Sep 2021 18:21:47 +0200, Konrad Dybcio wrote:
> Document Kryo 560 CPUs found in Qualcomm Snapdragon 690 (SM6350).
>
>
Applied, thanks!
[01/17] dt-bindings: arm: cpus: Add Kryo 560 CPUs
commit: 55d0feb3ab3de31320db41c92eaac6d73c644a6d
[02/17] arm64: dts: qcom: Add SM6350 device tree
commit: 5f82b9cda61e60a7f381a4aa427fa9eb472e581c
[03/17] arm64: dts: qcom: sm6350: Add LLCC node
commit: ced2f0d75e132a611f6239846b853452c23e6176
[04/17] arm64: dts: qcom: sm6350: Add RPMHCC node
commit: 985e02e7c0626a1e07c532bda5b6812f4ba5072c
[05/17] arm64: dts: qcom: sm6350: Add GCC node
commit: 30de1108df222e760297ed76f1ff1b4acc960dc7
[06/17] arm64: dts: qcom: sm6350: Add TLMM block node
commit: 538f4bcd5106aba43c5864ff86797662df8c30ec
[07/17] arm64: dts: qcom: sm6350: Add USB1 nodes
commit: 23737b9557fea0d3069b0fbbecce3b1c09737de5
[08/17] arm64: dts: qcom: sm6350: Add cpufreq-hw support
commit: 3cc415413f540403a0cbc36a49aa40ba764f708c
[09/17] arm64: dts: qcom: sm6350: Add TSENS nodes
commit: 25e0ae68481905f40c41d6b588d221354fb36055
[10/17] arm64: dts: qcom: sm6350: Add AOSS_QMP
commit: 8fe2e0d9dba8cafa98dbd6c8f3cfbc6a20bbc93a
[11/17] arm64: dts: qcom: sm6350: Add SPMI bus
commit: 001eaf9514f22eb9a01725a0c29b3f46cd7cdc0c
[12/17] arm64: dts: qcom: sm6350: Add PRNG node
commit: 574af54562440e7036a7b4a71d016f166ca2e830
[13/17] arm64: dts: qcom: sm6350: Add RPMHPD and BCM voter
commit: 9264d3c8ee511b5c246f2dd96fc94230c2b588f6
[14/17] arm64: dts: qcom: sm6350: Add SDHCI1/2 nodes
commit: 1797e1c9a95cd052ad481968e078c9f2beec0e8b
[15/17] arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1
commit: 4ef13f7fe4cd9e29118e09597b4fdd721fd24c11
[16/17] arm64: dts: qcom: Add device tree for Sony Xperia 10 III
commit: ed1648d52a375e606a0c88f5bf65282686ae6541
[17/17] arm64: dts: qcom: pm6150l: Add missing include
commit: a9a5ca5c8c37793aaf8fb99f593ac9ddad0bf0bf
Best regards,
--
Bjorn Andersson <bjorn.andersson@linaro.org>
^ permalink raw reply [flat|nested] 20+ messages in thread