[PATCH v2 00/11] Add Apple M1 support to PASemi i2c driver

[Sven Peter <sven@svenpeter.dev>]

Hi,

v1: https://lore.kernel.org/linux-i2c/20210926095847.38261-1-sven@svenpeter.dev/

Changes for v2:
 - Added reviewed-by/acks
 - Switched from ioport_map to pci_iomap as suggested by Arnd Bergmann
 - Renamed i2c-pasemi-apple.c to i2c-pasemi-platform.c as suggested by
   Wolfram Sang
 - Replaced the ioport number in the adapter name with dev_name to be
   able to identify separate busses in e.g. i2cdetect.

I still don't have access to any old PASemi hardware but the changes from
v1 are pretty small and I expect them to still work. Would still be nice
if someone with access to such hardware could give this a quick test.


And for those who didn't see v1 the (almost) unchanged original cover letter:

This series adds support for the I2C controller found on Apple Silicon Macs
which has quite a bit of history:

Apple bought P.A. Semi in 2008 and it looks like a part of its legacy continues
to live on in the M1. This controller has actually been used since at least the
iPhone 4S and hasn't changed much since then.
Essentially, there are only a few differences that matter:

	- The controller no longer is a PCI device
	- Starting at some iPhone an additional bit in one register
          must be set in order to start transmissions.
	- The reference clock and hence the clock dividers are different

In order to add support for a platform device I first replaced PCI-specific
bits and split out the PCI driver to its own file. Then I added support
to make the clock divider configurable and converted the driver to use
managed device resources to make it a bit simpler.

The Apple and PASemi driver will never be compiled in the same kernel
since the Apple one will run on arm64 while the original PASemi driver
will only be useful on powerpc.
I've thus followed the octeon (mips)/thunderx(arm64) approach to do the
split: I created a -core.c file which contains the shared logic and just
compile that one for both the PASemi and the new Apple driver.


Best,

Sven

Sven Peter (11):
  dt-bindings: i2c: Add Apple I2C controller bindings
  i2c: pasemi: Use io{read,write}32
  i2c: pasemi: Use dev_name instead of port number
  i2c: pasemi: Remove usage of pci_dev
  i2c: pasemi: Split off common probing code
  i2c: pasemi: Split pci driver to its own file
  i2c: pasemi: Move common reset code to own function
  i2c: pasemi: Allow to configure bus frequency
  i2c: pasemi: Refactor _probe to use devm_*
  i2c: pasemi: Add Apple platform driver
  i2c: pasemi: Set enable bit for Apple variant

 .../devicetree/bindings/i2c/apple,i2c.yaml    |  61 +++++++++
 MAINTAINERS                                   |   2 +
 drivers/i2c/busses/Kconfig                    |  11 ++
 drivers/i2c/busses/Makefile                   |   3 +
 .../{i2c-pasemi.c => i2c-pasemi-core.c}       | 114 +++++-----------
 drivers/i2c/busses/i2c-pasemi-core.h          |  21 +++
 drivers/i2c/busses/i2c-pasemi-pci.c           |  85 ++++++++++++
 drivers/i2c/busses/i2c-pasemi-platform.c      | 122 ++++++++++++++++++
 8 files changed, 334 insertions(+), 85 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/i2c/apple,i2c.yaml
 rename drivers/i2c/busses/{i2c-pasemi.c => i2c-pasemi-core.c} (77%)
 create mode 100644 drivers/i2c/busses/i2c-pasemi-core.h
 create mode 100644 drivers/i2c/busses/i2c-pasemi-pci.c
 create mode 100644 drivers/i2c/busses/i2c-pasemi-platform.c

-- 
2.25.1