From: youling257 <youling257@gmail.com>
To: mathias.nyman@linux.intel.com
Cc: gregkh@linuxfoundation.org, linux-usb@vger.kernel.org,
pkondeti@codeaurora.org, stable@vger.kernel.org
Subject: Re: [PATCH 4/5] xhci: Fix command ring pointer corruption while aborting a command
Date: Fri, 22 Oct 2021 18:59:13 +0800 [thread overview]
Message-ID: <20211022105913.7671-1-youling257@gmail.com> (raw)
In-Reply-To: <20211008092547.3996295-5-mathias.nyman@linux.intel.com>
This patch cause suspend to disk resume usb not work, xhci_hcd 0000:00:14.0: Abort failed to stop command ring: -110.
[ 189.292054] PM: hibernation: hibernation entry
[ 189.295273] Filesystems sync: 0.000 seconds
[ 189.295281] Freezing user space processes ... (elapsed 0.003 seconds) done.
[ 189.298514] OOM killer disabled.
[ 189.298590] PM: hibernation: Marking nosave pages: [mem 0x00000000-0x00000fff]
[ 189.298594] PM: hibernation: Marking nosave pages: [mem 0x00058000-0x00058fff]
[ 189.298596] PM: hibernation: Marking nosave pages: [mem 0x0009f000-0x000fffff]
[ 189.298600] PM: hibernation: Marking nosave pages: [mem 0x00500000-0x005fffff]
[ 189.298607] PM: hibernation: Marking nosave pages: [mem 0x850d7000-0x850d8fff]
[ 189.298609] PM: hibernation: Marking nosave pages: [mem 0x8805d000-0x8809bfff]
[ 189.298612] PM: hibernation: Marking nosave pages: [mem 0x8ac24000-0x8ac24fff]
[ 189.298614] PM: hibernation: Marking nosave pages: [mem 0x8bea8000-0x8caeefff]
[ 189.298689] PM: hibernation: Marking nosave pages: [mem 0x8cb9a000-0x8d3fefff]
[ 189.298741] PM: hibernation: Marking nosave pages: [mem 0x8d400000-0xffffffff]
[ 189.300918] PM: hibernation: Basic memory bitmaps created
[ 189.301088] PM: hibernation: Preallocating image memory
[ 189.812115] PM: hibernation: Allocated 779311 pages for snapshot
[ 189.812118] PM: hibernation: Allocated 3117244 kbytes in 0.51 seconds (6112.24 MB/s)
[ 189.812121] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 189.813884] printk: Suspending console(s) (use no_console_suspend to debug)
[ 189.814016] wlan0: deauthenticating from b4:a8:98:22:f9:ac by local choice (Reason: 3=DEAUTH_LEAVING)
[ 189.814310] rtc_cmos 00:05: suspend, ctrl 02
[ 189.844670] r8169 0000:01:00.0 eth0: Link is Down
[ 190.081522] ACPI: PM: Preparing to enter system sleep state S4
[ 190.083051] ACPI: PM: Saving platform NVS memory
[ 190.087556] Disabling non-boot CPUs ...
[ 190.089802] smpboot: CPU 1 is now offline
[ 190.092841] smpboot: CPU 2 is now offline
[ 190.095235] smpboot: CPU 3 is now offline
[ 190.098592] smpboot: CPU 4 is now offline
[ 190.100660] smpboot: CPU 5 is now offline
[ 190.102967] smpboot: CPU 6 is now offline
[ 190.105047] smpboot: CPU 7 is now offline
[ 190.106828] PM: hibernation: Creating image:
[ 190.211897] PM: hibernation: Need to copy 775681 pages
[ 190.211898] PM: hibernation: Normal pages needed: 775681 + 1024, available pages: 1300224
[ 190.107012] ACPI: PM: Restoring platform NVS memory
[ 190.108184] Enabling non-boot CPUs ...
[ 190.108225] x86: Booting SMP configuration:
[ 190.108225] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 190.109416] CPU1 is up
[ 190.109440] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 190.110088] CPU2 is up
[ 190.110111] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 190.110775] CPU3 is up
[ 190.110799] smpboot: Booting Node 0 Processor 4 APIC 0x1
[ 190.111532] CPU4 is up
[ 190.111558] smpboot: Booting Node 0 Processor 5 APIC 0x3
[ 190.112280] CPU5 is up
[ 190.112303] smpboot: Booting Node 0 Processor 6 APIC 0x5
[ 190.113056] CPU6 is up
[ 190.113084] smpboot: Booting Node 0 Processor 7 APIC 0x7
[ 190.113886] CPU7 is up
[ 190.116276] ACPI: PM: Waking up from system sleep state S4
[ 190.187264] usb usb1: root hub lost power or was reset
[ 190.187296] usb usb2: root hub lost power or was reset
[ 190.188384] rtc_cmos 00:05: resume, ctrl 02
[ 190.189946] i915 0000:00:02.0: [drm] [ENCODER:94:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI clock, gate it
[ 190.195185] nvme nvme0: 8/0/0 default/read/poll queues
[ 190.354168] r8169 0000:01:00.0 eth0: Link is Down
[ 190.526336] ata3: SATA link down (SStatus 4 SControl 300)
[ 190.526389] ata4: SATA link down (SStatus 4 SControl 300)
[ 191.214037] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x206f0015
[ 191.214047] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214054] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214058] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214061] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214064] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214067] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214070] snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x206f0015
[ 191.214073] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214076] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214079] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 192.216095] snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x20670100
[ 193.218095] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to single_cmd mode: last cmd=0x20670100
[ 193.547924] r8169 0000:01:00.0 eth0: Link is Up - 1Gbps/Full - flow control off
[ 200.640141] xhci_hcd 0000:00:14.0: Abort failed to stop command ring: -110
[ 200.640148] xhci_hcd 0000:00:14.0: xHCI host controller not responding, assume dead
[ 200.640151] xhci_hcd 0000:00:14.0: HC died; cleaning up
[ 200.640165] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 201.056143] usb 2-1: device not accepting address 2, error -22
[ 201.058193] PM: hibernation: Basic memory bitmaps freed
[ 201.058197] OOM killer enabled.
[ 201.058197] Restarting tasks ...
[ 201.058212] usb 2-1: USB disconnect, device number 2
next prev parent reply other threads:[~2021-10-22 10:59 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-08 9:25 [PATCH 0/5] xhci fixes for usb-linus Mathias Nyman
2021-10-08 9:25 ` [PATCH 1/5] xhci: guard accesses to ep_state in xhci_endpoint_reset() Mathias Nyman
2021-10-08 9:25 ` [PATCH 2/5] xhci: add quirk for host controllers that don't update endpoint DCS Mathias Nyman
2021-10-08 9:25 ` [PATCH 3/5] USB: xhci: dbc: fix tty registration race Mathias Nyman
2021-10-08 9:25 ` [PATCH 4/5] xhci: Fix command ring pointer corruption while aborting a command Mathias Nyman
2021-10-22 10:59 ` youling257 [this message]
2021-10-22 11:00 ` youling 257
2021-10-25 11:21 ` Mathias Nyman
2021-10-25 15:01 ` youling 257
2021-10-25 15:21 ` Mathias Nyman
2021-10-26 10:49 ` Pavan Kondeti
2021-10-27 13:59 ` Mathias Nyman
2021-10-28 8:03 ` Pavan Kondeti
2021-10-29 12:48 ` Mathias Nyman
2021-10-29 12:51 ` [RFT PATCH] xhci: Fix commad ring abort, write all 64 bits to CRCR register Mathias Nyman
2021-10-29 15:35 ` youling 257
2021-11-01 8:37 ` Mathias Nyman
2021-11-01 3:31 ` Pavan Kondeti
2021-11-01 8:36 ` Mathias Nyman
2021-10-08 9:25 ` [PATCH 5/5] xhci: Enable trust tx length quirk for Fresco FL11 USB controller Mathias Nyman
2021-10-08 16:13 ` [PATCH 0/5] xhci fixes for usb-linus Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211022105913.7671-1-youling257@gmail.com \
--to=youling257@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-usb@vger.kernel.org \
--cc=mathias.nyman@linux.intel.com \
--cc=pkondeti@codeaurora.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.