* [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM
@ 2021-10-23 18:33 Marek Vasut
2021-10-23 18:33 ` [PATCH 2/2] ARM: stm32: Disable video output " Marek Vasut
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Marek Vasut @ 2021-10-23 18:33 UTC (permalink / raw)
To: u-boot; +Cc: Marek Vasut, Patrice Chotard, Patrick Delaunay
The EFI support is unused and disabling it saves about 70 kiB of space.
In case EFI support is required, it can be re-enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
configs/stm32mp15_dhcom_basic_defconfig | 4 ++++
configs/stm32mp15_dhcor_basic_defconfig | 4 ++++
2 files changed, 8 insertions(+)
diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig
index 8fe0456a56d..ae9c3cdc25f 100644
--- a/configs/stm32mp15_dhcom_basic_defconfig
+++ b/configs/stm32mp15_dhcom_basic_defconfig
@@ -62,6 +62,8 @@ CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_MTDPARTS=y
# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_ISO_PARTITION is not set
+# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_OF_LIST="stm32mp15xx-dhcom-pdk2 stm32mp15xx-dhcom-drc02 stm32mp15xx-dhcom-picoitx"
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
CONFIG_ENV_IS_IN_SPI_FLASH=y
@@ -157,5 +159,7 @@ CONFIG_VIDEO_BMP_RLE8=y
CONFIG_BMP_16BPP=y
CONFIG_BMP_24BPP=y
CONFIG_BMP_32BPP=y
+CONFIG_FAT_WRITE=y
CONFIG_LZO=y
CONFIG_FDT_FIXUP_PARTITIONS=y
+# CONFIG_EFI_LOADER is not set
diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
index 21f5c9e01b2..98ba37c750e 100644
--- a/configs/stm32mp15_dhcor_basic_defconfig
+++ b/configs/stm32mp15_dhcor_basic_defconfig
@@ -60,6 +60,8 @@ CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_MTDPARTS=y
# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_ISO_PARTITION is not set
+# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_USE_ENV_SPI_BUS=y
@@ -151,5 +153,7 @@ CONFIG_VIDEO_BMP_RLE8=y
CONFIG_BMP_16BPP=y
CONFIG_BMP_24BPP=y
CONFIG_BMP_32BPP=y
+CONFIG_FAT_WRITE=y
CONFIG_LZO=y
CONFIG_FDT_FIXUP_PARTITIONS=y
+# CONFIG_EFI_LOADER is not set
--
2.33.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/2] ARM: stm32: Disable video output on DHSOM
2021-10-23 18:33 [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM Marek Vasut
@ 2021-10-23 18:33 ` Marek Vasut
2021-10-25 6:46 ` Patrice CHOTARD
2021-10-25 8:30 ` Patrick DELAUNAY
2021-10-25 6:45 ` [PATCH 1/2] ARM: stm32: Disable EFI " Patrice CHOTARD
2021-10-25 8:29 ` Patrick DELAUNAY
2 siblings, 2 replies; 8+ messages in thread
From: Marek Vasut @ 2021-10-23 18:33 UTC (permalink / raw)
To: u-boot; +Cc: Marek Vasut, Patrice Chotard, Patrick Delaunay
The video output support is unused and disabling it saves about 20 kiB of space.
In case video output support is required, it can be re-enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
configs/stm32mp15_dhcom_basic_defconfig | 14 +-------------
configs/stm32mp15_dhcor_basic_defconfig | 14 +-------------
2 files changed, 2 insertions(+), 26 deletions(-)
diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig
index ae9c3cdc25f..5ecc91c7c1b 100644
--- a/configs/stm32mp15_dhcom_basic_defconfig
+++ b/configs/stm32mp15_dhcom_basic_defconfig
@@ -22,6 +22,7 @@ CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcom.its"
# CONFIG_USE_SPL_FIT_GENERATOR is not set
CONFIG_BOOTDELAY=1
CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_CONSOLE_MUX=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
@@ -53,7 +54,6 @@ CONFIG_CMD_REMOTEPROC=y
CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_TIMER=y
@@ -147,18 +147,6 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0483
CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
CONFIG_USB_GADGET_DWC2_OTG=y
CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_DM_VIDEO=y
-CONFIG_BACKLIGHT_GPIO=y
-CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
-CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
-CONFIG_VIDEO_STM32=y
-CONFIG_VIDEO_STM32_DSI=y
-CONFIG_VIDEO_STM32_MAX_XRES=1280
-CONFIG_VIDEO_STM32_MAX_YRES=800
-CONFIG_VIDEO_BMP_RLE8=y
-CONFIG_BMP_16BPP=y
-CONFIG_BMP_24BPP=y
-CONFIG_BMP_32BPP=y
CONFIG_FAT_WRITE=y
CONFIG_LZO=y
CONFIG_FDT_FIXUP_PARTITIONS=y
diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
index 98ba37c750e..7c410b8224a 100644
--- a/configs/stm32mp15_dhcor_basic_defconfig
+++ b/configs/stm32mp15_dhcor_basic_defconfig
@@ -20,6 +20,7 @@ CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its"
# CONFIG_USE_SPL_FIT_GENERATOR is not set
CONFIG_BOOTDELAY=1
CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_CONSOLE_MUX=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
@@ -51,7 +52,6 @@ CONFIG_CMD_REMOTEPROC=y
CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_BMP=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_TIMER=y
@@ -141,18 +141,6 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0483
CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
CONFIG_USB_GADGET_DWC2_OTG=y
CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_DM_VIDEO=y
-CONFIG_BACKLIGHT_GPIO=y
-CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
-CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
-CONFIG_VIDEO_STM32=y
-CONFIG_VIDEO_STM32_DSI=y
-CONFIG_VIDEO_STM32_MAX_XRES=1280
-CONFIG_VIDEO_STM32_MAX_YRES=800
-CONFIG_VIDEO_BMP_RLE8=y
-CONFIG_BMP_16BPP=y
-CONFIG_BMP_24BPP=y
-CONFIG_BMP_32BPP=y
CONFIG_FAT_WRITE=y
CONFIG_LZO=y
CONFIG_FDT_FIXUP_PARTITIONS=y
--
2.33.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM
2021-10-23 18:33 [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM Marek Vasut
2021-10-23 18:33 ` [PATCH 2/2] ARM: stm32: Disable video output " Marek Vasut
@ 2021-10-25 6:45 ` Patrice CHOTARD
2021-10-25 8:29 ` Patrick DELAUNAY
2 siblings, 0 replies; 8+ messages in thread
From: Patrice CHOTARD @ 2021-10-25 6:45 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrick Delaunay
Hi Marek
On 10/23/21 8:33 PM, Marek Vasut wrote:
> The EFI support is unused and disabling it saves about 70 kiB of space.
> In case EFI support is required, it can be re-enabled.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> configs/stm32mp15_dhcom_basic_defconfig | 4 ++++
> configs/stm32mp15_dhcor_basic_defconfig | 4 ++++
> 2 files changed, 8 insertions(+)
>
> diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig
> index 8fe0456a56d..ae9c3cdc25f 100644
> --- a/configs/stm32mp15_dhcom_basic_defconfig
> +++ b/configs/stm32mp15_dhcom_basic_defconfig
> @@ -62,6 +62,8 @@ CONFIG_CMD_REGULATOR=y
> CONFIG_CMD_EXT4_WRITE=y
> CONFIG_CMD_MTDPARTS=y
> # CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_ISO_PARTITION is not set
> +# CONFIG_SPL_PARTITION_UUIDS is not set
> CONFIG_OF_LIST="stm32mp15xx-dhcom-pdk2 stm32mp15xx-dhcom-drc02 stm32mp15xx-dhcom-picoitx"
> CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
> CONFIG_ENV_IS_IN_SPI_FLASH=y
> @@ -157,5 +159,7 @@ CONFIG_VIDEO_BMP_RLE8=y
> CONFIG_BMP_16BPP=y
> CONFIG_BMP_24BPP=y
> CONFIG_BMP_32BPP=y
> +CONFIG_FAT_WRITE=y
> CONFIG_LZO=y
> CONFIG_FDT_FIXUP_PARTITIONS=y
> +# CONFIG_EFI_LOADER is not set
> diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
> index 21f5c9e01b2..98ba37c750e 100644
> --- a/configs/stm32mp15_dhcor_basic_defconfig
> +++ b/configs/stm32mp15_dhcor_basic_defconfig
> @@ -60,6 +60,8 @@ CONFIG_CMD_REGULATOR=y
> CONFIG_CMD_EXT4_WRITE=y
> CONFIG_CMD_MTDPARTS=y
> # CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_ISO_PARTITION is not set
> +# CONFIG_SPL_PARTITION_UUIDS is not set
> CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
> CONFIG_ENV_IS_IN_SPI_FLASH=y
> CONFIG_USE_ENV_SPI_BUS=y
> @@ -151,5 +153,7 @@ CONFIG_VIDEO_BMP_RLE8=y
> CONFIG_BMP_16BPP=y
> CONFIG_BMP_24BPP=y
> CONFIG_BMP_32BPP=y
> +CONFIG_FAT_WRITE=y
> CONFIG_LZO=y
> CONFIG_FDT_FIXUP_PARTITIONS=y
> +# CONFIG_EFI_LOADER is not set
>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Thanks
Patrice
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 2/2] ARM: stm32: Disable video output on DHSOM
2021-10-23 18:33 ` [PATCH 2/2] ARM: stm32: Disable video output " Marek Vasut
@ 2021-10-25 6:46 ` Patrice CHOTARD
2021-10-25 8:30 ` Patrick DELAUNAY
1 sibling, 0 replies; 8+ messages in thread
From: Patrice CHOTARD @ 2021-10-25 6:46 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrick Delaunay
Hi Marek
On 10/23/21 8:33 PM, Marek Vasut wrote:
> The video output support is unused and disabling it saves about 20 kiB of space.
> In case video output support is required, it can be re-enabled.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> configs/stm32mp15_dhcom_basic_defconfig | 14 +-------------
> configs/stm32mp15_dhcor_basic_defconfig | 14 +-------------
> 2 files changed, 2 insertions(+), 26 deletions(-)
>
> diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig
> index ae9c3cdc25f..5ecc91c7c1b 100644
> --- a/configs/stm32mp15_dhcom_basic_defconfig
> +++ b/configs/stm32mp15_dhcom_basic_defconfig
> @@ -22,6 +22,7 @@ CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcom.its"
> # CONFIG_USE_SPL_FIT_GENERATOR is not set
> CONFIG_BOOTDELAY=1
> CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> +CONFIG_CONSOLE_MUX=y
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> @@ -53,7 +54,6 @@ CONFIG_CMD_REMOTEPROC=y
> CONFIG_CMD_SPI=y
> CONFIG_CMD_USB=y
> CONFIG_CMD_USB_MASS_STORAGE=y
> -CONFIG_CMD_BMP=y
> CONFIG_CMD_CACHE=y
> CONFIG_CMD_TIME=y
> CONFIG_CMD_TIMER=y
> @@ -147,18 +147,6 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0483
> CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
> CONFIG_USB_GADGET_DWC2_OTG=y
> CONFIG_USB_GADGET_DOWNLOAD=y
> -CONFIG_DM_VIDEO=y
> -CONFIG_BACKLIGHT_GPIO=y
> -CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
> -CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
> -CONFIG_VIDEO_STM32=y
> -CONFIG_VIDEO_STM32_DSI=y
> -CONFIG_VIDEO_STM32_MAX_XRES=1280
> -CONFIG_VIDEO_STM32_MAX_YRES=800
> -CONFIG_VIDEO_BMP_RLE8=y
> -CONFIG_BMP_16BPP=y
> -CONFIG_BMP_24BPP=y
> -CONFIG_BMP_32BPP=y
> CONFIG_FAT_WRITE=y
> CONFIG_LZO=y
> CONFIG_FDT_FIXUP_PARTITIONS=y
> diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
> index 98ba37c750e..7c410b8224a 100644
> --- a/configs/stm32mp15_dhcor_basic_defconfig
> +++ b/configs/stm32mp15_dhcor_basic_defconfig
> @@ -20,6 +20,7 @@ CONFIG_SPL_FIT_SOURCE="board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its"
> # CONFIG_USE_SPL_FIT_GENERATOR is not set
> CONFIG_BOOTDELAY=1
> CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> +CONFIG_CONSOLE_MUX=y
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y
> CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> @@ -51,7 +52,6 @@ CONFIG_CMD_REMOTEPROC=y
> CONFIG_CMD_SPI=y
> CONFIG_CMD_USB=y
> CONFIG_CMD_USB_MASS_STORAGE=y
> -CONFIG_CMD_BMP=y
> CONFIG_CMD_CACHE=y
> CONFIG_CMD_TIME=y
> CONFIG_CMD_TIMER=y
> @@ -141,18 +141,6 @@ CONFIG_USB_GADGET_VENDOR_NUM=0x0483
> CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
> CONFIG_USB_GADGET_DWC2_OTG=y
> CONFIG_USB_GADGET_DOWNLOAD=y
> -CONFIG_DM_VIDEO=y
> -CONFIG_BACKLIGHT_GPIO=y
> -CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
> -CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
> -CONFIG_VIDEO_STM32=y
> -CONFIG_VIDEO_STM32_DSI=y
> -CONFIG_VIDEO_STM32_MAX_XRES=1280
> -CONFIG_VIDEO_STM32_MAX_YRES=800
> -CONFIG_VIDEO_BMP_RLE8=y
> -CONFIG_BMP_16BPP=y
> -CONFIG_BMP_24BPP=y
> -CONFIG_BMP_32BPP=y
> CONFIG_FAT_WRITE=y
> CONFIG_LZO=y
> CONFIG_FDT_FIXUP_PARTITIONS=y
>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Thanks
Patrice
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM
2021-10-23 18:33 [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM Marek Vasut
2021-10-23 18:33 ` [PATCH 2/2] ARM: stm32: Disable video output " Marek Vasut
2021-10-25 6:45 ` [PATCH 1/2] ARM: stm32: Disable EFI " Patrice CHOTARD
@ 2021-10-25 8:29 ` Patrick DELAUNAY
2021-11-10 15:57 ` Patrice CHOTARD
2 siblings, 1 reply; 8+ messages in thread
From: Patrick DELAUNAY @ 2021-10-25 8:29 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrice Chotard
Hi,
On 10/23/21 8:33 PM, Marek Vasut wrote:
> The EFI support is unused and disabling it saves about 70 kiB of space.
> In case EFI support is required, it can be re-enabled.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> configs/stm32mp15_dhcom_basic_defconfig | 4 ++++
> configs/stm32mp15_dhcor_basic_defconfig | 4 ++++
> 2 files changed, 8 insertions(+)
>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Thanks
Patrick
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 2/2] ARM: stm32: Disable video output on DHSOM
2021-10-23 18:33 ` [PATCH 2/2] ARM: stm32: Disable video output " Marek Vasut
2021-10-25 6:46 ` Patrice CHOTARD
@ 2021-10-25 8:30 ` Patrick DELAUNAY
2021-11-10 15:57 ` Patrice CHOTARD
1 sibling, 1 reply; 8+ messages in thread
From: Patrick DELAUNAY @ 2021-10-25 8:30 UTC (permalink / raw)
To: Marek Vasut, u-boot; +Cc: Patrice Chotard
Hi,
On 10/23/21 8:33 PM, Marek Vasut wrote:
> The video output support is unused and disabling it saves about 20 kiB of space.
> In case video output support is required, it can be re-enabled.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
> configs/stm32mp15_dhcom_basic_defconfig | 14 +-------------
> configs/stm32mp15_dhcor_basic_defconfig | 14 +-------------
> 2 files changed, 2 insertions(+), 26 deletions(-)
>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Thanks
Patrick
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 2/2] ARM: stm32: Disable video output on DHSOM
2021-10-25 8:30 ` Patrick DELAUNAY
@ 2021-11-10 15:57 ` Patrice CHOTARD
0 siblings, 0 replies; 8+ messages in thread
From: Patrice CHOTARD @ 2021-11-10 15:57 UTC (permalink / raw)
To: Patrick DELAUNAY, Marek Vasut, u-boot
Hi Marek
On 10/25/21 10:30 AM, Patrick DELAUNAY wrote:
> Hi,
>
> On 10/23/21 8:33 PM, Marek Vasut wrote:
>> The video output support is unused and disabling it saves about 20 kiB of space.
>> In case video output support is required, it can be re-enabled.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
>> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
>> ---
>> configs/stm32mp15_dhcom_basic_defconfig | 14 +-------------
>> configs/stm32mp15_dhcor_basic_defconfig | 14 +-------------
>> 2 files changed, 2 insertions(+), 26 deletions(-)
>>
>
>
> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
>
> Thanks
> Patrick
>
Applied on u-boot-stm/master
Thanks
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM
2021-10-25 8:29 ` Patrick DELAUNAY
@ 2021-11-10 15:57 ` Patrice CHOTARD
0 siblings, 0 replies; 8+ messages in thread
From: Patrice CHOTARD @ 2021-11-10 15:57 UTC (permalink / raw)
To: Patrick DELAUNAY, Marek Vasut, u-boot
Hi Marek
On 10/25/21 10:29 AM, Patrick DELAUNAY wrote:
> Hi,
>
> On 10/23/21 8:33 PM, Marek Vasut wrote:
>> The EFI support is unused and disabling it saves about 70 kiB of space.
>> In case EFI support is required, it can be re-enabled.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
>> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
>> ---
>> configs/stm32mp15_dhcom_basic_defconfig | 4 ++++
>> configs/stm32mp15_dhcor_basic_defconfig | 4 ++++
>> 2 files changed, 8 insertions(+)
>>
>
> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
>
> Thanks
> Patrick
>
Applied on u-boot-stm/master
Thanks
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2021-11-10 15:58 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-10-23 18:33 [PATCH 1/2] ARM: stm32: Disable EFI on DHSOM Marek Vasut
2021-10-23 18:33 ` [PATCH 2/2] ARM: stm32: Disable video output " Marek Vasut
2021-10-25 6:46 ` Patrice CHOTARD
2021-10-25 8:30 ` Patrick DELAUNAY
2021-11-10 15:57 ` Patrice CHOTARD
2021-10-25 6:45 ` [PATCH 1/2] ARM: stm32: Disable EFI " Patrice CHOTARD
2021-10-25 8:29 ` Patrick DELAUNAY
2021-11-10 15:57 ` Patrice CHOTARD
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.