[PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Neil Armstrong]

This adds support for the Synopsys DWMAC controller found in the
OX820SE SoC, by using almost the same glue code as the OX820.

Patch 1 & 2 are for net branch, patch 3 will be queued to arm-soc.

Changes since v1:
- correctly update value read from register
- add proper tag on patch 3 for arm-soc tree

Neil Armstrong (3):
  dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE
  net: stmmac: dwmac-oxnas: Add support for OX810SE
  ARM: dts: ox810se: Add Ethernet support

 .../devicetree/bindings/net/oxnas-dwmac.txt   |   3 +
 arch/arm/boot/dts/ox810se-wd-mbwe.dts         |   4 +
 arch/arm/boot/dts/ox810se.dtsi                |  18 +++
 .../net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 115 +++++++++++++-----
 4 files changed, 111 insertions(+), 29 deletions(-)

-- 
2.25.1

[PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Neil Armstrong]

This adds support for the Synopsys DWMAC controller found in the
OX820SE SoC, by using almost the same glue code as the OX820.

Patch 1 & 2 are for net branch, patch 3 will be queued to arm-soc.

Changes since v1:
- correctly update value read from register
- add proper tag on patch 3 for arm-soc tree

Neil Armstrong (3):
  dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE
  net: stmmac: dwmac-oxnas: Add support for OX810SE
  ARM: dts: ox810se: Add Ethernet support

 .../devicetree/bindings/net/oxnas-dwmac.txt   |   3 +
 arch/arm/boot/dts/ox810se-wd-mbwe.dts         |   4 +
 arch/arm/boot/dts/ox810se.dtsi                |  18 +++
 .../net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 115 +++++++++++++-----
 4 files changed, 111 insertions(+), 29 deletions(-)

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v2 1/3] dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE

[Neil Armstrong]

Add SoC specific bindings for OX810SE support.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 Documentation/devicetree/bindings/net/oxnas-dwmac.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
index d7117a22fd87..27db496f1ce8 100644
--- a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
+++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
@@ -9,6 +9,9 @@ Required properties on all platforms:
 - compatible:	For the OX820 SoC, it should be :
 		- "oxsemi,ox820-dwmac" to select glue
 		- "snps,dwmac-3.512" to select IP version.
+		For the OX810SE SoC, it should be :
+		- "oxsemi,ox810se-dwmac" to select glue
+		- "snps,dwmac-3.512" to select IP version.
 
 - clocks: Should contain phandles to the following clocks
 - clock-names:	Should contain the following:
-- 
2.25.1

[PATCH net-next v2 1/3] dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE

[Neil Armstrong]

Add SoC specific bindings for OX810SE support.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 Documentation/devicetree/bindings/net/oxnas-dwmac.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
index d7117a22fd87..27db496f1ce8 100644
--- a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
+++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt
@@ -9,6 +9,9 @@ Required properties on all platforms:
 - compatible:	For the OX820 SoC, it should be :
 		- "oxsemi,ox820-dwmac" to select glue
 		- "snps,dwmac-3.512" to select IP version.
+		For the OX810SE SoC, it should be :
+		- "oxsemi,ox810se-dwmac" to select glue
+		- "snps,dwmac-3.512" to select IP version.
 
 - clocks: Should contain phandles to the following clocks
 - clock-names:	Should contain the following:
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH net-next v2 2/3] net: stmmac: dwmac-oxnas: Add support for OX810SE

[Neil Armstrong]

Add support for OX810SE dwmac glue setup, which is a simplified version
of the OX820 introduced later with more control on the PHY interface.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 115 +++++++++++++-----
 1 file changed, 86 insertions(+), 29 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
index adfeb8d3293d..62a69a91ab22 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
@@ -12,6 +12,7 @@
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/mfd/syscon.h>
@@ -48,16 +49,75 @@
 #define DWMAC_RX_VARDELAY(d)		((d) << DWMAC_RX_VARDELAY_SHIFT)
 #define DWMAC_RXN_VARDELAY(d)		((d) << DWMAC_RXN_VARDELAY_SHIFT)
 
+struct oxnas_dwmac;
+
+struct oxnas_dwmac_data {
+	int (*setup)(struct oxnas_dwmac *dwmac);
+};
+
 struct oxnas_dwmac {
 	struct device	*dev;
 	struct clk	*clk;
 	struct regmap	*regmap;
+	const struct oxnas_dwmac_data	*data;
 };
 
+static int oxnas_dwmac_setup_ox810se(struct oxnas_dwmac *dwmac)
+{
+	unsigned int value;
+	int ret;
+
+	ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
+	if (ret < 0)
+		return ret;
+
+	/* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+	value |= BIT(DWMAC_CKEN_GTX)		|
+		 /* Use simple mux for 25/125 Mhz clock switching */
+		 BIT(DWMAC_SIMPLE_MUX);
+
+	regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+
+	return 0;
+}
+
+static int oxnas_dwmac_setup_ox820(struct oxnas_dwmac *dwmac)
+{
+	unsigned int value;
+	int ret;
+
+	ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
+	if (ret < 0)
+		return ret;
+
+	/* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+	value |= BIT(DWMAC_CKEN_GTX)		|
+		 /* Use simple mux for 25/125 Mhz clock switching */
+		BIT(DWMAC_SIMPLE_MUX)		|
+		/* set auto switch tx clock source */
+		BIT(DWMAC_AUTO_TX_SOURCE)	|
+		/* enable tx & rx vardelay */
+		BIT(DWMAC_CKEN_TX_OUT)		|
+		BIT(DWMAC_CKEN_TXN_OUT)	|
+		BIT(DWMAC_CKEN_TX_IN)		|
+		BIT(DWMAC_CKEN_RX_OUT)		|
+		BIT(DWMAC_CKEN_RXN_OUT)	|
+		BIT(DWMAC_CKEN_RX_IN);
+	regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+
+	/* set tx & rx vardelay */
+	value = DWMAC_TX_VARDELAY(4)	|
+		DWMAC_TXN_VARDELAY(2)	|
+		DWMAC_RX_VARDELAY(10)	|
+		DWMAC_RXN_VARDELAY(8);
+	regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
+
+	return 0;
+}
+
 static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
 {
 	struct oxnas_dwmac *dwmac = priv;
-	unsigned int value;
 	int ret;
 
 	/* Reset HW here before changing the glue configuration */
@@ -69,35 +129,11 @@ static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
 	if (ret)
 		return ret;
 
-	ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
-	if (ret < 0) {
+	ret = dwmac->data->setup(dwmac);
+	if (ret)
 		clk_disable_unprepare(dwmac->clk);
-		return ret;
-	}
 
-	/* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
-	value |= BIT(DWMAC_CKEN_GTX)		|
-		 /* Use simple mux for 25/125 Mhz clock switching */
-		 BIT(DWMAC_SIMPLE_MUX)		|
-		 /* set auto switch tx clock source */
-		 BIT(DWMAC_AUTO_TX_SOURCE)	|
-		 /* enable tx & rx vardelay */
-		 BIT(DWMAC_CKEN_TX_OUT)		|
-		 BIT(DWMAC_CKEN_TXN_OUT)	|
-		 BIT(DWMAC_CKEN_TX_IN)		|
-		 BIT(DWMAC_CKEN_RX_OUT)		|
-		 BIT(DWMAC_CKEN_RXN_OUT)	|
-		 BIT(DWMAC_CKEN_RX_IN);
-	regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
-
-	/* set tx & rx vardelay */
-	value = DWMAC_TX_VARDELAY(4)	|
-		DWMAC_TXN_VARDELAY(2)	|
-		DWMAC_RX_VARDELAY(10)	|
-		DWMAC_RXN_VARDELAY(8);
-	regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
-
-	return 0;
+	return ret;
 }
 
 static void oxnas_dwmac_exit(struct platform_device *pdev, void *priv)
@@ -128,6 +164,12 @@ static int oxnas_dwmac_probe(struct platform_device *pdev)
 		goto err_remove_config_dt;
 	}
 
+	dwmac->data = (const struct oxnas_dwmac_data *)of_device_get_match_data(&pdev->dev);
+	if (!dwmac->data) {
+		ret = -EINVAL;
+		goto err_remove_config_dt;
+	}
+
 	dwmac->dev = &pdev->dev;
 	plat_dat->bsp_priv = dwmac;
 	plat_dat->init = oxnas_dwmac_init;
@@ -166,8 +208,23 @@ static int oxnas_dwmac_probe(struct platform_device *pdev)
 	return ret;
 }
 
+static const struct oxnas_dwmac_data ox810se_dwmac_data = {
+	.setup = oxnas_dwmac_setup_ox810se,
+};
+
+static const struct oxnas_dwmac_data ox820_dwmac_data = {
+	.setup = oxnas_dwmac_setup_ox820,
+};
+
 static const struct of_device_id oxnas_dwmac_match[] = {
-	{ .compatible = "oxsemi,ox820-dwmac" },
+	{
+		.compatible = "oxsemi,ox810se-dwmac",
+		.data = &ox810se_dwmac_data,
+	},
+	{
+		.compatible = "oxsemi,ox820-dwmac",
+		.data = &ox820_dwmac_data,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, oxnas_dwmac_match);
-- 
2.25.1

[PATCH net-next v2 2/3] net: stmmac: dwmac-oxnas: Add support for OX810SE

[Neil Armstrong]

Add support for OX810SE dwmac glue setup, which is a simplified version
of the OX820 introduced later with more control on the PHY interface.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-oxnas.c | 115 +++++++++++++-----
 1 file changed, 86 insertions(+), 29 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
index adfeb8d3293d..62a69a91ab22 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-oxnas.c
@@ -12,6 +12,7 @@
 #include <linux/io.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/mfd/syscon.h>
@@ -48,16 +49,75 @@
 #define DWMAC_RX_VARDELAY(d)		((d) << DWMAC_RX_VARDELAY_SHIFT)
 #define DWMAC_RXN_VARDELAY(d)		((d) << DWMAC_RXN_VARDELAY_SHIFT)
 
+struct oxnas_dwmac;
+
+struct oxnas_dwmac_data {
+	int (*setup)(struct oxnas_dwmac *dwmac);
+};
+
 struct oxnas_dwmac {
 	struct device	*dev;
 	struct clk	*clk;
 	struct regmap	*regmap;
+	const struct oxnas_dwmac_data	*data;
 };
 
+static int oxnas_dwmac_setup_ox810se(struct oxnas_dwmac *dwmac)
+{
+	unsigned int value;
+	int ret;
+
+	ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
+	if (ret < 0)
+		return ret;
+
+	/* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+	value |= BIT(DWMAC_CKEN_GTX)		|
+		 /* Use simple mux for 25/125 Mhz clock switching */
+		 BIT(DWMAC_SIMPLE_MUX);
+
+	regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+
+	return 0;
+}
+
+static int oxnas_dwmac_setup_ox820(struct oxnas_dwmac *dwmac)
+{
+	unsigned int value;
+	int ret;
+
+	ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
+	if (ret < 0)
+		return ret;
+
+	/* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
+	value |= BIT(DWMAC_CKEN_GTX)		|
+		 /* Use simple mux for 25/125 Mhz clock switching */
+		BIT(DWMAC_SIMPLE_MUX)		|
+		/* set auto switch tx clock source */
+		BIT(DWMAC_AUTO_TX_SOURCE)	|
+		/* enable tx & rx vardelay */
+		BIT(DWMAC_CKEN_TX_OUT)		|
+		BIT(DWMAC_CKEN_TXN_OUT)	|
+		BIT(DWMAC_CKEN_TX_IN)		|
+		BIT(DWMAC_CKEN_RX_OUT)		|
+		BIT(DWMAC_CKEN_RXN_OUT)	|
+		BIT(DWMAC_CKEN_RX_IN);
+	regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
+
+	/* set tx & rx vardelay */
+	value = DWMAC_TX_VARDELAY(4)	|
+		DWMAC_TXN_VARDELAY(2)	|
+		DWMAC_RX_VARDELAY(10)	|
+		DWMAC_RXN_VARDELAY(8);
+	regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
+
+	return 0;
+}
+
 static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
 {
 	struct oxnas_dwmac *dwmac = priv;
-	unsigned int value;
 	int ret;
 
 	/* Reset HW here before changing the glue configuration */
@@ -69,35 +129,11 @@ static int oxnas_dwmac_init(struct platform_device *pdev, void *priv)
 	if (ret)
 		return ret;
 
-	ret = regmap_read(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, &value);
-	if (ret < 0) {
+	ret = dwmac->data->setup(dwmac);
+	if (ret)
 		clk_disable_unprepare(dwmac->clk);
-		return ret;
-	}
 
-	/* Enable GMII_GTXCLK to follow GMII_REFCLK, required for gigabit PHY */
-	value |= BIT(DWMAC_CKEN_GTX)		|
-		 /* Use simple mux for 25/125 Mhz clock switching */
-		 BIT(DWMAC_SIMPLE_MUX)		|
-		 /* set auto switch tx clock source */
-		 BIT(DWMAC_AUTO_TX_SOURCE)	|
-		 /* enable tx & rx vardelay */
-		 BIT(DWMAC_CKEN_TX_OUT)		|
-		 BIT(DWMAC_CKEN_TXN_OUT)	|
-		 BIT(DWMAC_CKEN_TX_IN)		|
-		 BIT(DWMAC_CKEN_RX_OUT)		|
-		 BIT(DWMAC_CKEN_RXN_OUT)	|
-		 BIT(DWMAC_CKEN_RX_IN);
-	regmap_write(dwmac->regmap, OXNAS_DWMAC_CTRL_REGOFFSET, value);
-
-	/* set tx & rx vardelay */
-	value = DWMAC_TX_VARDELAY(4)	|
-		DWMAC_TXN_VARDELAY(2)	|
-		DWMAC_RX_VARDELAY(10)	|
-		DWMAC_RXN_VARDELAY(8);
-	regmap_write(dwmac->regmap, OXNAS_DWMAC_DELAY_REGOFFSET, value);
-
-	return 0;
+	return ret;
 }
 
 static void oxnas_dwmac_exit(struct platform_device *pdev, void *priv)
@@ -128,6 +164,12 @@ static int oxnas_dwmac_probe(struct platform_device *pdev)
 		goto err_remove_config_dt;
 	}
 
+	dwmac->data = (const struct oxnas_dwmac_data *)of_device_get_match_data(&pdev->dev);
+	if (!dwmac->data) {
+		ret = -EINVAL;
+		goto err_remove_config_dt;
+	}
+
 	dwmac->dev = &pdev->dev;
 	plat_dat->bsp_priv = dwmac;
 	plat_dat->init = oxnas_dwmac_init;
@@ -166,8 +208,23 @@ static int oxnas_dwmac_probe(struct platform_device *pdev)
 	return ret;
 }
 
+static const struct oxnas_dwmac_data ox810se_dwmac_data = {
+	.setup = oxnas_dwmac_setup_ox810se,
+};
+
+static const struct oxnas_dwmac_data ox820_dwmac_data = {
+	.setup = oxnas_dwmac_setup_ox820,
+};
+
 static const struct of_device_id oxnas_dwmac_match[] = {
-	{ .compatible = "oxsemi,ox820-dwmac" },
+	{
+		.compatible = "oxsemi,ox810se-dwmac",
+		.data = &ox810se_dwmac_data,
+	},
+	{
+		.compatible = "oxsemi,ox820-dwmac",
+		.data = &ox820_dwmac_data,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, oxnas_dwmac_match);
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH arm-soc-next v2 3/3] ARM: dts: ox810se: Add Ethernet support

[Neil Armstrong]

Add nodes for the embedded Synopsys DWMAC Ethernet controller.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/boot/dts/ox810se-wd-mbwe.dts |  4 ++++
 arch/arm/boot/dts/ox810se.dtsi        | 18 ++++++++++++++++++
 2 files changed, 22 insertions(+)

diff --git a/arch/arm/boot/dts/ox810se-wd-mbwe.dts b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
index 7e2fcb220aea..c59e06ff2423 100644
--- a/arch/arm/boot/dts/ox810se-wd-mbwe.dts
+++ b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
@@ -103,6 +103,10 @@ rtc0: rtc@48 {
 	};
 };
 
+&etha {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/ox810se.dtsi b/arch/arm/boot/dts/ox810se.dtsi
index 0755e5864c4a..96c0745f7b70 100644
--- a/arch/arm/boot/dts/ox810se.dtsi
+++ b/arch/arm/boot/dts/ox810se.dtsi
@@ -81,6 +81,24 @@ soc {
 		ranges;
 		interrupt-parent = <&intc>;
 
+		etha: ethernet@40400000 {
+			compatible = "oxsemi,ox810se-dwmac", "snps,dwmac";
+			reg = <0x40400000 0x2000>;
+			interrupts = <8>;
+			interrupt-names = "macirq";
+			mac-address = [000000000000]; /* Filled in by U-Boot */
+			phy-mode = "rgmii";
+
+			clocks = <&stdclk 6>, <&gmacclk>;
+			clock-names = "gmac", "stmmaceth";
+			resets = <&reset 6>;
+
+			/* Regmap for sys registers */
+			oxsemi,sys-ctrl = <&sys>;
+
+			status = "disabled";
+		};
+
 		apb-bridge@44000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-- 
2.25.1

[PATCH arm-soc-next v2 3/3] ARM: dts: ox810se: Add Ethernet support

[Neil Armstrong]

Add nodes for the embedded Synopsys DWMAC Ethernet controller.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/boot/dts/ox810se-wd-mbwe.dts |  4 ++++
 arch/arm/boot/dts/ox810se.dtsi        | 18 ++++++++++++++++++
 2 files changed, 22 insertions(+)

diff --git a/arch/arm/boot/dts/ox810se-wd-mbwe.dts b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
index 7e2fcb220aea..c59e06ff2423 100644
--- a/arch/arm/boot/dts/ox810se-wd-mbwe.dts
+++ b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
@@ -103,6 +103,10 @@ rtc0: rtc@48 {
 	};
 };
 
+&etha {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/ox810se.dtsi b/arch/arm/boot/dts/ox810se.dtsi
index 0755e5864c4a..96c0745f7b70 100644
--- a/arch/arm/boot/dts/ox810se.dtsi
+++ b/arch/arm/boot/dts/ox810se.dtsi
@@ -81,6 +81,24 @@ soc {
 		ranges;
 		interrupt-parent = <&intc>;
 
+		etha: ethernet@40400000 {
+			compatible = "oxsemi,ox810se-dwmac", "snps,dwmac";
+			reg = <0x40400000 0x2000>;
+			interrupts = <8>;
+			interrupt-names = "macirq";
+			mac-address = [000000000000]; /* Filled in by U-Boot */
+			phy-mode = "rgmii";
+
+			clocks = <&stdclk 6>, <&gmacclk>;
+			clock-names = "gmac", "stmmaceth";
+			resets = <&reset 6>;
+
+			/* Regmap for sys registers */
+			oxsemi,sys-ctrl = <&sys>;
+
+			status = "disabled";
+		};
+
 		apb-bridge@44000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Jakub Kicinski]

On Tue,  4 Jan 2022 15:56:43 +0100 Neil Armstrong wrote:
> This adds support for the Synopsys DWMAC controller found in the
> OX820SE SoC, by using almost the same glue code as the OX820.
> 
> Patch 1 & 2 are for net branch, patch 3 will be queued to arm-soc.
> 
> Changes since v1:
> - correctly update value read from register
> - add proper tag on patch 3 for arm-soc tree

Waiting for Rob's ack, I just noticed you haven't CCed him directly.
Adding his address now, but not sure if that's enough...

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Jakub Kicinski]

On Tue,  4 Jan 2022 15:56:43 +0100 Neil Armstrong wrote:
> This adds support for the Synopsys DWMAC controller found in the
> OX820SE SoC, by using almost the same glue code as the OX820.
> 
> Patch 1 & 2 are for net branch, patch 3 will be queued to arm-soc.
> 
> Changes since v1:
> - correctly update value read from register
> - add proper tag on patch 3 for arm-soc tree

Waiting for Rob's ack, I just noticed you haven't CCed him directly.
Adding his address now, but not sure if that's enough...

Re: [PATCH net-next v2 1/3] dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE

[Rob Herring]

On Tue, 04 Jan 2022 15:56:44 +0100, Neil Armstrong wrote:
> Add SoC specific bindings for OX810SE support.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  Documentation/devicetree/bindings/net/oxnas-dwmac.txt | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH net-next v2 1/3] dt-bindings: net: oxnas-dwmac: Add bindings for OX810SE

[Rob Herring]

On Tue, 04 Jan 2022 15:56:44 +0100, Neil Armstrong wrote:
> Add SoC specific bindings for OX810SE support.
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  Documentation/devicetree/bindings/net/oxnas-dwmac.txt | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Jakub Kicinski]

On Tue,  4 Jan 2022 15:56:43 +0100 Neil Armstrong wrote:
> This adds support for the Synopsys DWMAC controller found in the
> OX820SE SoC, by using almost the same glue code as the OX820.

Alright, patches 1 and 2 are in net and on their way to 5.17. Thanks!

Re: [PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Jakub Kicinski]

On Tue,  4 Jan 2022 15:56:43 +0100 Neil Armstrong wrote:
> This adds support for the Synopsys DWMAC controller found in the
> OX820SE SoC, by using almost the same glue code as the OX820.

Alright, patches 1 and 2 are in net and on their way to 5.17. Thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Neil Armstrong]

Hi,

On Tue, 4 Jan 2022 15:56:43 +0100, Neil Armstrong wrote:
> This adds support for the Synopsys DWMAC controller found in the
> OX820SE SoC, by using almost the same glue code as the OX820.
> 
> Patch 1 & 2 are for net branch, patch 3 will be queued to arm-soc.
> 
> Changes since v1:
> - correctly update value read from register
> - add proper tag on patch 3 for arm-soc tree
> 
> [...]

Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/narmstrong/linux-oxnas.git (v5.18/dt)

[3/3] ARM: dts: ox810se: Add Ethernet support
      https://git.kernel.org/narmstrong/linux-oxnas/c/ae552c33f6edad1097dec7a5543314d35d413b3e

-- 
Neil

Re: [PATCH v2 0/3] ARM: ox810se: Add Ethernet support

[Neil Armstrong]

Hi,

On Tue, 4 Jan 2022 15:56:43 +0100, Neil Armstrong wrote:
> This adds support for the Synopsys DWMAC controller found in the
> OX820SE SoC, by using almost the same glue code as the OX820.
> 
> Patch 1 & 2 are for net branch, patch 3 will be queued to arm-soc.
> 
> Changes since v1:
> - correctly update value read from register
> - add proper tag on patch 3 for arm-soc tree
> 
> [...]

Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/narmstrong/linux-oxnas.git (v5.18/dt)

[3/3] ARM: dts: ox810se: Add Ethernet support
      https://git.kernel.org/narmstrong/linux-oxnas/c/ae552c33f6edad1097dec7a5543314d35d413b3e

-- 
Neil

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel