* [PATCH v11, 2/2] net: Add dm9051 driver
2022-01-13 7:46 [PATCH v11, 0/2] ADD DM9051 ETHERNET DRIVER Joseph CHAMG
2022-01-13 7:46 ` [PATCH v11, 1/2] yaml: Add dm9051 SPI network yaml file Joseph CHAMG
@ 2022-01-13 7:46 ` Joseph CHAMG
2022-01-13 10:16 ` Andy Shevchenko
1 sibling, 1 reply; 5+ messages in thread
From: Joseph CHAMG @ 2022-01-13 7:46 UTC (permalink / raw)
To: David S . Miller, Jakub Kicinski, Rob Herring, Joseph CHANG,
joseph_chang
Cc: netdev, devicetree, linux-kernel, Andrew Lunn, Leon Romanovsky,
andy Shevchenko, kernel test robot
v1-v4
Add davicom dm9051 spi ethernet driver. The driver work for the
device platform with spi master
Test ok with raspberry pi 2 and pi 4, the spi configure used in
my raspberry pi 4 is spi0.1, spi speed 31200000, and INT by pin 26.
v5
Work to eliminate the wrappers to be clear for read, swapped to
phylib for phy connection tasks.
Tested with raspberry pi 4. Test for netwroking function, CAT5
cable unplug/plug and also ethtool detect for link state, and
all are ok.
v6
remove the redundant code that phylib has support,
adjust to be the reasonable sequence,
fine tune comments, add comments for pause function support
Tested with raspberry pi 4. Test for netwroking function, CAT5
cable unplug/plug and also ethtool detect for link state, and
all are ok.
v7
read/write registers must return error code to the callet,
add to enable pause processing
v8
not parmanently set MAC by .ndo_set_mac_address
correct rx function such as clear ISR,
inblk avoid stack buffer,
simple skb buffer process and
easy use netif_rx_ni.
simplely queue init and wake the queues,
limit the start_xmit function use netif_stop_queue.
descript that schedule delay is essential
for tx_work and rxctrl_work
eliminate ____cacheline_aligned and
add static int msg_enable.
v9
use phylib, no need 'select MII' in Kconfig,
make it clear in dm9051_xfer when using spi_sync,
improve the registers read/write so that error code
return as far as possible up the call stack.
v10
use regmap APIs for SPI and MDIO,
modify to correcting such as include header files
and program check styles
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joseph CHAMG <josright123@gmail.com>
---
v11
eliminate the redundant code for struct regmap_config data
use regmap_read_poll_timeout
use corresponding regmap APIs, i.e. MDIO, SPI
all read/write registers by regmap
all read/write registers with mutex lock by regmap
problem: regmap MDIO and SPI has no .reg_update_bits, I write it
in the driver
problem: this chip can support bulk read/write to rx/tx data, but
can not support bulk read/write to continue registers, so need
read/write register one by one
---
drivers/net/ethernet/davicom/Kconfig | 29 +
drivers/net/ethernet/davicom/Makefile | 1 +
drivers/net/ethernet/davicom/dm9051.c | 1169 +++++++++++++++++++++++++
drivers/net/ethernet/davicom/dm9051.h | 198 +++++
4 files changed, 1397 insertions(+)
create mode 100644 drivers/net/ethernet/davicom/dm9051.c
create mode 100644 drivers/net/ethernet/davicom/dm9051.h
diff --git a/drivers/net/ethernet/davicom/Kconfig b/drivers/net/ethernet/davicom/Kconfig
index 7af86b6d4150..887fe6e56d56 100644
--- a/drivers/net/ethernet/davicom/Kconfig
+++ b/drivers/net/ethernet/davicom/Kconfig
@@ -3,6 +3,19 @@
# Davicom device configuration
#
+config NET_VENDOR_DAVICOM
+ bool "Davicom devices"
+ default y
+ help
+ If you have a network (Ethernet) card belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Davicom devices. If you say Y, you will be asked
+ for your specific card in the following selections.
+
+if NET_VENDOR_DAVICOM
+
config DM9000
tristate "DM9000 support"
depends on ARM || MIPS || COLDFIRE || NIOS2 || COMPILE_TEST
@@ -22,3 +35,19 @@ config DM9000_FORCE_SIMPLE_PHY_POLL
bit to determine if the link is up or down instead of the more
costly MII PHY reads. Note, this will not work if the chip is
operating with an external PHY.
+
+config DM9051
+ tristate "DM9051 SPI support"
+ select PHYLIB
+ depends on SPI
+ select CRC32
+ help
+ Support for DM9051 SPI chipset.
+
+ To compile this driver as a module, choose M here. The module
+ will be called dm9051.
+
+ The SPI mode for the host's SPI master to access DM9051 is mode
+ 0 on the SPI bus.
+
+endif # NET_VENDOR_DAVICOM
diff --git a/drivers/net/ethernet/davicom/Makefile b/drivers/net/ethernet/davicom/Makefile
index 173c87d21076..225f85bc1f53 100644
--- a/drivers/net/ethernet/davicom/Makefile
+++ b/drivers/net/ethernet/davicom/Makefile
@@ -4,3 +4,4 @@
#
obj-$(CONFIG_DM9000) += dm9000.o
+obj-$(CONFIG_DM9051) += dm9051.o
diff --git a/drivers/net/ethernet/davicom/dm9051.c b/drivers/net/ethernet/davicom/dm9051.c
new file mode 100644
index 000000000000..212cec48603b
--- /dev/null
+++ b/drivers/net/ethernet/davicom/dm9051.c
@@ -0,0 +1,1169 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2021 Davicom Semiconductor,Inc.
+ * Davicom DM9051 SPI Fast Ethernet Linux driver
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/mii.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/phy.h>
+#include <linux/regmap.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/spi/spi.h>
+
+#include "dm9051.h"
+
+static int dm9051_map_read(struct board_info *db, u8 reg, unsigned int *prb)
+{
+ struct net_device *ndev = db->ndev;
+ int ret = regmap_read(db->regmap, reg, prb);
+
+ if (unlikely(ret))
+ netif_err(db, drv, ndev, "%s: error %d reading reg %02x\n",
+ __func__, ret, reg);
+ return ret;
+}
+
+static int dm9051_map_write(struct board_info *db, u8 reg, u16 val)
+{
+ struct net_device *ndev = db->ndev;
+ int ret = regmap_write(db->regmap, reg, val);
+
+ if (unlikely(ret))
+ netif_err(db, drv, ndev, "%s: error %d writing reg %02x=%04x\n",
+ __func__, ret, reg, val);
+ return ret;
+}
+
+/* waiting tx-end rather than tx-req
+ * got faster
+ */
+static int dm9051_map_xmitpoll(struct board_info *db)
+{
+ unsigned int mval;
+ int ret = regmap_read_poll_timeout(db->regmap, DM9051_NSR, mval,
+ mval & (NSR_TX2END | NSR_TX1END), 1, 20);
+
+ if (ret)
+ netdev_err(db->ndev, "timeout in checking for tx ends\n");
+ return ret;
+}
+
+static int dm9051_map_ee_phypoll(struct board_info *db)
+{
+ unsigned int mval;
+ int ret = regmap_read_poll_timeout(db->regmap, DM9051_EPCR, mval,
+ !(mval & EPCR_ERRE), 100, 10000);
+
+ if (ret)
+ netdev_err(db->ndev, "eeprom/phy in processing get timeout\n");
+ return ret;
+}
+
+static int ctrl_dm9051_phywrite(void *context, unsigned int reg, unsigned int val)
+{
+ struct board_info *db = context;
+ int ret;
+
+ ret = dm9051_map_write(db, DM9051_EPAR, DM9051_PHY | reg);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_EPDRL, val & 0xff); /* write ctl must once 8-bit */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_EPDRH, val >> 8); /* write ctl must once 8-bit */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_EPCR, EPCR_EPOS | EPCR_ERPRW);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_ee_phypoll(db);
+ if (ret)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_EPCR, 0x0);
+ if (ret < 0)
+ return ret;
+
+ /* chip internal operation need wait 1 ms for if power-up phy
+ */
+ if (reg == MII_BMCR && !(val & BMCR_PDOWN))
+ mdelay(1);
+ return ret;
+}
+
+static int ctrl_dm9051_phyread(void *context, unsigned int reg, unsigned int *val)
+{
+ struct board_info *db = context;
+ unsigned int eph, epl;
+ int ret;
+
+ ret = dm9051_map_write(db, DM9051_EPAR, DM9051_PHY | reg);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_EPCR, EPCR_ERPRR | EPCR_EPOS);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_ee_phypoll(db);
+ if (ret)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_EPCR, 0x0);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_read(db, DM9051_EPDRH, &eph); /* read ctl must once 8-bit */
+ if (ret)
+ return ret;
+ ret = dm9051_map_read(db, DM9051_EPDRL, &epl); /* read ctl must once 8-bit */
+ if (ret)
+ return ret;
+ *val = (eph << 8) | epl;
+ return ret;
+}
+
+static bool dm9051_regmap_volatile(struct device *dev, unsigned int reg)
+{
+ return true; /* true, register can not be cached */
+}
+
+static void dm9051_reg_lock_mutex(void *dbcontext)
+{
+ struct board_info *db = dbcontext;
+
+ mutex_lock(&db->reg_mutex);
+}
+
+static void dm9051_reg_unlock_mutex(void *dbcontext)
+{
+ struct board_info *db = dbcontext;
+
+ mutex_unlock(&db->reg_mutex);
+}
+
+static struct regmap_config regconfig = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = 0xff,
+ .reg_stride = 1,
+ .cache_type = REGCACHE_NONE, /* cache none, so _map_bulk as well as _map_noinc read */
+ .read_flag_mask = 0,
+ .write_flag_mask = DM_SPI_WR,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+ .volatile_reg = dm9051_regmap_volatile,
+ .lock = dm9051_reg_lock_mutex,
+ .unlock = dm9051_reg_unlock_mutex,
+};
+
+static int dm9051_map_outblk(struct board_info *db, u8 reg, const u8 *data,
+ size_t count)
+{
+ struct net_device *ndev = db->ndev;
+ int ret = regmap_noinc_write(db->regmap, reg, data, count);
+
+ if (unlikely(ret))
+ netif_err(db, drv, ndev, "%s: error %d bulk writing reg %02x, len %d\n",
+ __func__, ret, reg, count);
+ return ret;
+}
+
+static int dm9051_map_inblk(struct board_info *db, u8 reg, u8 *data, size_t count)
+{
+ struct net_device *ndev = db->ndev;
+ int ret = regmap_noinc_read(db->regmap, reg, data, count);
+
+ if (unlikely(ret))
+ netif_err(db, drv, ndev, "%s: error %d bulk reading reg %02x, len %d\n",
+ __func__, ret, reg, count);
+ return ret;
+}
+
+/* skb buffer exhausted, just discard the received data
+ */
+static int dm9051_map_dumpblk(struct board_info *db, u8 reg, size_t count)
+{
+ struct net_device *ndev = db->ndev;
+ unsigned int rb;
+ int ret;
+
+ while (count--) {
+ ret = regmap_read(db->regmap, reg, &rb); /* read only one byte */
+ if (unlikely(ret))
+ netif_err(db, drv, ndev, "%s: error %d dump reading reg %02x\n",
+ __func__, ret, reg);
+ }
+ return ret;
+}
+
+static int dm9051_map_updbits(struct board_info *db, unsigned int reg,
+ unsigned int mask, unsigned int val)
+{
+ unsigned int set_mask = val & mask;
+ unsigned int readd = 0; /* clear all insided bits */
+ int ret = 0;
+
+ ret = regmap_read(db->regmap, reg, &readd);
+ if (ret < 0)
+ return ret;
+
+ if ((readd & mask) != set_mask) {
+ readd &= ~mask;
+ readd |= set_mask;
+
+ ret = regmap_write(db->regmap, reg, readd);
+ if (ret < 0)
+ return ret;
+ }
+ return ret;
+}
+
+static bool dm9051_phymap_volatile(struct device *dev, unsigned int reg)
+{
+ return true; /* true, register can not be cached */
+}
+
+static struct regmap_config phyconfig = {
+ .reg_bits = 5,
+ .val_bits = 16,
+ .max_register = 0x1f,
+ .cache_type = REGCACHE_RBTREE,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+ .volatile_reg = dm9051_phymap_volatile,
+};
+
+static int dm9051_map_phy_updbits(struct board_info *db, unsigned int reg,
+ unsigned int mask, unsigned int val)
+{
+ unsigned int set_mask = mask & val;
+ unsigned int readd = 0;
+ int ret;
+
+ ret = ctrl_dm9051_phyread(db, reg, &readd);
+ if (ret)
+ return ret;
+
+ if ((readd & mask) != set_mask) {
+ readd &= ~mask;
+ readd |= set_mask;
+ ret = ctrl_dm9051_phywrite(db, reg, readd);
+ if (ret)
+ return ret;
+ }
+ return ret;
+}
+
+static int dm9051_mdiobus_read(struct mii_bus *mdiobus, int phy_id, int reg)
+{
+ struct board_info *db = mdiobus->priv;
+ int val, ret;
+
+ if (phy_id == DM9051_PHY_ID) {
+ ret = ctrl_dm9051_phyread(db, reg, &val);
+ if (ret)
+ return ret;
+ return val;
+ }
+ return 0xffff;
+}
+
+static int dm9051_mdiobus_write(struct mii_bus *mdiobus, int phy_id, int reg, u16 val)
+{
+ struct board_info *db = mdiobus->priv;
+ int ret;
+
+ if (phy_id == DM9051_PHY_ID) {
+ ret = ctrl_dm9051_phywrite(db, reg, val);
+ if (ret)
+ return ret;
+ return 0;
+ }
+ return -ENODEV;
+}
+
+static int dm9051_map_eeread(struct board_info *db, int offset, u8 *to)
+{
+ unsigned int mval;
+ int ret;
+
+ dm9051_map_write(db, DM9051_EPAR, offset);
+ dm9051_map_write(db, DM9051_EPCR, EPCR_ERPRR);
+ ret = dm9051_map_ee_phypoll(db);
+ dm9051_map_write(db, DM9051_EPCR, 0x0);
+ ret = dm9051_map_read(db, DM9051_EPDRL, &mval); /* must read once 8-bit */
+ if (ret < 0)
+ return ret;
+ to[0] = mval;
+ ret = dm9051_map_read(db, DM9051_EPDRH, &mval); /* must read once 8-bit */
+ if (ret < 0)
+ return ret;
+ to[1] = mval;
+ return ret;
+}
+
+static int dm9051_map_eewrite(struct board_info *db, int offset, u8 *data)
+{
+ int ret;
+
+ dm9051_map_write(db, DM9051_EPAR, offset);
+ dm9051_map_write(db, DM9051_EPDRH, data[1]); /* must write once 8-bit */
+ dm9051_map_write(db, DM9051_EPDRL, data[0]); /* must write once 8-bit */
+ dm9051_map_write(db, DM9051_EPCR, EPCR_WEP | EPCR_ERPRW);
+ ret = dm9051_map_ee_phypoll(db);
+ dm9051_map_write(db, DM9051_EPCR, 0);
+ return ret;
+}
+
+static int dm9051_map_chipid(struct board_info *db)
+{
+ struct device *dev = &db->spidev->dev;
+ unsigned int wpidh, wpidl, ret;
+ u16 id;
+
+ ret = dm9051_map_read(db, DM9051_PIDH, &wpidh);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_read(db, DM9051_PIDL, &wpidl);
+ if (ret < 0)
+ return ret;
+
+ id = (wpidh << 8) | wpidl;
+ if (id == DM9051_ID) {
+ dev_info(dev, "chip %04x found\n", id);
+ return 0;
+ }
+
+ dev_info(dev, "chipid error as %04x !\n", id);
+ return -ENODEV;
+}
+
+/* mac address is major from EEPROM
+ */
+static int dm9051_map_init_macaddr(struct net_device *ndev, struct board_info *db)
+{
+ u8 addr[ETH_ALEN];
+ unsigned int mval;
+ int i, ret;
+
+ /* these registers can't read by inblk, must read one by one
+ */
+ for (i = 0; i < ETH_ALEN; i++) {
+ ret = dm9051_map_read(db, DM9051_PAR + i, &mval);
+ if (unlikely(ret))
+ return ret;
+ addr[i] = mval;
+ }
+
+ if (is_valid_ether_addr(addr)) {
+ eth_hw_addr_set(ndev, addr);
+ return 0;
+ }
+
+ eth_hw_addr_random(ndev);
+ dev_dbg(&db->spidev->dev, "Use random MAC address\n");
+ return 0;
+}
+
+static void dm9051_handle_link_change(struct net_device *ndev)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ int lcl_adv, rmt_adv;
+ u8 fcr = 0;
+
+ phy_print_status(ndev->phydev);
+
+ /* only write pause settings to mac. since mac and phy are integrated
+ * together, such as link state, speed and duplex are sync already
+ */
+ if (ndev->phydev->link) {
+ if (db->eth_pause.autoneg == AUTONEG_ENABLE) {
+ lcl_adv = linkmode_adv_to_mii_adv_t(db->phydev->advertising);
+ rmt_adv = linkmode_adv_to_mii_adv_t(db->phydev->lp_advertising);
+
+ if (lcl_adv & rmt_adv & ADVERTISE_PAUSE_CAP) {
+ db->eth_pause.rx_pause = true;
+ db->eth_pause.tx_pause = true;
+ }
+ }
+
+ /* while both rx_pause & tx_pause
+ * fcr will result idenical as FCR_RXTX_ENABLE
+ */
+ if (db->eth_pause.rx_pause)
+ fcr |= FCR_BKPM | FCR_FLCE;
+ if (db->eth_pause.tx_pause)
+ fcr |= FCR_TXPEN;
+
+ dm9051_map_updbits(db, DM9051_FCR, 0xff, fcr);
+ }
+}
+
+static int dm9051_phy_connect(struct board_info *db)
+{
+ char phy_id[MII_BUS_ID_SIZE + 3];
+
+ snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT,
+ db->mdiobus->id, DM9051_PHY_ID);
+ db->phydev = phy_connect(db->ndev, phy_id, dm9051_handle_link_change,
+ PHY_INTERFACE_MODE_MII);
+
+ if (IS_ERR(db->phydev))
+ return PTR_ERR(db->phydev);
+ return 0;
+}
+
+/* ethtool-ops
+ */
+static void dm9051_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
+{
+ strscpy(info->driver, DRVNAME_9051, sizeof(info->driver));
+}
+
+static void dm9051_set_msglevel(struct net_device *ndev, u32 value)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+
+ db->msg_enable = value;
+}
+
+static u32 dm9051_get_msglevel(struct net_device *ndev)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+
+ return db->msg_enable;
+}
+
+static int dm9051_get_eeprom_len(struct net_device *dev)
+{
+ return 128;
+}
+
+static int dm9051_get_eeprom(struct net_device *ndev,
+ struct ethtool_eeprom *ee, u8 *data)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ int offset = ee->offset;
+ int len = ee->len;
+ int i, ret;
+
+ if ((len | offset) & 1)
+ return -EINVAL;
+
+ ee->magic = DM_EEPROM_MAGIC;
+
+ for (i = 0; i < len; i += 2) {
+ ret = dm9051_map_eeread(db, (offset + i) / 2, data + i);
+ if (ret)
+ break;
+ }
+ return ret;
+}
+
+static int dm9051_set_eeprom(struct net_device *ndev,
+ struct ethtool_eeprom *ee, u8 *data)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ int offset = ee->offset;
+ int len = ee->len;
+ int i, ret;
+
+ if ((len | offset) & 1)
+ return -EINVAL;
+
+ if (ee->magic != DM_EEPROM_MAGIC)
+ return -EINVAL;
+
+ for (i = 0; i < len; i += 2) {
+ ret = dm9051_map_eewrite(db, (offset + i) / 2, data + i);
+ if (ret)
+ break;
+ }
+ return ret;
+}
+
+static void dm9051_get_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *pause)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+
+ *pause = db->eth_pause;
+}
+
+static int dm9051_set_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *pause)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ u8 fcr = 0;
+
+ db->eth_pause = *pause;
+
+ if (pause->autoneg)
+ db->phydev->autoneg = AUTONEG_ENABLE;
+ else
+ db->phydev->autoneg = AUTONEG_DISABLE;
+
+ if (pause->rx_pause)
+ fcr |= FCR_BKPM | FCR_FLCE;
+ if (pause->tx_pause)
+ fcr |= FCR_TXPEN;
+
+ return dm9051_map_updbits(db, DM9051_FCR, 0xff, fcr);
+}
+
+static const struct ethtool_ops dm9051_ethtool_ops = {
+ .get_drvinfo = dm9051_get_drvinfo,
+ .get_link_ksettings = phy_ethtool_get_link_ksettings,
+ .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_msglevel = dm9051_get_msglevel,
+ .set_msglevel = dm9051_set_msglevel,
+ .nway_reset = phy_ethtool_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_eeprom_len = dm9051_get_eeprom_len,
+ .get_eeprom = dm9051_get_eeprom,
+ .set_eeprom = dm9051_set_eeprom,
+ .get_pauseparam = dm9051_get_pauseparam,
+ .set_pauseparam = dm9051_set_pauseparam,
+};
+
+static int dm9051_direct_reset_code(struct board_info *db)
+{
+ int ret;
+
+ db->bc.DO_FIFO_RST_counter++;
+
+ ret = dm9051_map_write(db, DM9051_NCR, NCR_RST); /* NCR reset */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_MBNDRY, MBNDRY_BYTE); /* MemBound */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_PPCR, PPCR_PAUSE_COUNT); /* Pause Count */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_LMCR, db->lcr_all); /* LEDMode1 */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_INTCR, INTCR_POL_LOW); /* INTCR */
+ if (ret < 0)
+ return ret;
+ return ret;
+}
+
+/* reset while rx error found
+ */
+static int dm9051_direct_fifo_reset(struct board_info *db)
+{
+ struct net_device *ndev = db->ndev;
+ int rxlen = le16_to_cpu(db->eth_rxhdr.rxlen);
+ u8 fcr = 0;
+ int ret;
+
+ ret = dm9051_direct_reset_code(db);
+ if (ret < 0)
+ return ret;
+
+ if (db->eth_pause.rx_pause)
+ fcr |= FCR_BKPM | FCR_FLCE;
+ if (db->eth_pause.tx_pause)
+ fcr |= FCR_TXPEN;
+
+ ret = dm9051_map_write(db, DM9051_FCR, fcr);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_IMR, db->imr_all); /* rxp to 0xc00 */
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_RCR, db->rcr_all); /* enable rx all */
+ if (ret < 0)
+ return ret;
+
+ netdev_dbg(ndev, "rxhdr-byte (%02x)\n",
+ db->eth_rxhdr.rxpktready);
+ netdev_dbg(ndev, "check rxstatus-eror (%02x)\n",
+ db->eth_rxhdr.rxstatus);
+ netdev_dbg(ndev, "check rxlen large-eror (%d > %d)\n",
+ rxlen, DM9051_PKT_MAX);
+
+ netdev_dbg(ndev, " rxstatus_Er & rxlen_Er %d, RST_c %d\n",
+ db->bc.status_err_counter + db->bc.large_err_counter,
+ db->bc.DO_FIFO_RST_counter);
+ return ret;
+}
+
+/* read packets from the fifo memory
+ * return value,
+ * > 0 - read packet number, caller can repeat the rx operation
+ * 0 - no error, caller need stop further rx operation
+ * -EBUSY - read data error, caller escape from rx operation
+ */
+static int dm9051_loop_rx(struct board_info *db)
+{
+ unsigned int rxbyte;
+ int ret, rxlen;
+ struct sk_buff *skb;
+ u8 *rdptr;
+ int scanrr = 0;
+
+ do {
+ ret = dm9051_map_read(db, DM_SPI_MRCMDX, &rxbyte);
+ if (ret < 0) {
+ netdev_err(db->ndev, "read MRCMDX fail\n");
+ return ret;
+ }
+ ret = dm9051_map_read(db, DM_SPI_MRCMDX, &rxbyte);
+ if (ret < 0) {
+ netdev_err(db->ndev, "read MRCMDX fail\n");
+ return ret;
+ }
+
+ if (rxbyte != DM9051_PKT_RDY)
+ break; /* exhaust-empty */
+
+ ret = dm9051_map_inblk(db, DM_SPI_MRCMD, (u8 *)&db->eth_rxhdr, DM_RXHDR_SIZE);
+ if (ret < 0)
+ return ret;
+
+ ret = dm9051_map_write(db, DM9051_ISR, 0xff); /* to stop mrcmd */
+ if (ret < 0)
+ return ret;
+
+ rxlen = le16_to_cpu(db->eth_rxhdr.rxlen);
+ if (db->eth_rxhdr.rxstatus & RSR_ERR_BITS || rxlen > DM9051_PKT_MAX) {
+ if (db->eth_rxhdr.rxstatus & RSR_ERR_BITS)
+ db->bc.status_err_counter++;
+ else
+ db->bc.large_err_counter++;
+ ret = dm9051_direct_fifo_reset(db);
+ if (ret < 0)
+ return ret;
+ return 0;
+ }
+
+ skb = dev_alloc_skb(rxlen);
+ if (!skb) {
+ ret = dm9051_map_dumpblk(db, DM_SPI_MRCMD, rxlen);
+ if (ret < 0)
+ return ret;
+ return scanrr;
+ }
+
+ rdptr = (u8 *)skb_put(skb, rxlen - 4);
+ ret = dm9051_map_inblk(db, DM_SPI_MRCMD, rdptr, rxlen);
+ if (ret < 0) {
+ dev_kfree_skb(skb);
+ return ret;
+ }
+
+ ret = dm9051_map_write(db, DM9051_ISR, 0xff); /* to stop mrcmd */
+ if (ret < 0)
+ return ret;
+
+ skb->protocol = eth_type_trans(skb, db->ndev);
+ if (db->ndev->features & NETIF_F_RXCSUM)
+ skb_checksum_none_assert(skb);
+ netif_rx_ni(skb);
+ db->ndev->stats.rx_bytes += rxlen;
+ db->ndev->stats.rx_packets++;
+ scanrr++;
+ } while (!ret);
+ return scanrr;
+}
+
+/* transmit a packet,
+ * return value,
+ * 0 - succeed
+ * -ETIMEDOUT - timeout error
+ */
+static int dm9051_single_tx(struct board_info *db, u8 *buff, unsigned int len)
+{
+ int ret;
+
+ ret = dm9051_map_xmitpoll(db);
+ if (ret)
+ return -ETIMEDOUT;
+
+ ret = dm9051_map_outblk(db, DM_SPI_MWCMD, buff, len);
+ if (ret < 0)
+ return ret;
+
+ ret = dm9051_map_write(db, DM9051_TXPLL, len);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_TXPLH, len >> 8);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_map_write(db, DM9051_TCR, TCR_TXREQ);
+ if (ret < 0)
+ return ret;
+ return 0;
+}
+
+static int dm9051_loop_tx(struct board_info *db)
+{
+ struct net_device *ndev = db->ndev;
+ int ntx = 0;
+ int ret;
+
+ while (!skb_queue_empty(&db->txq)) {
+ struct sk_buff *skb;
+
+ skb = skb_dequeue(&db->txq);
+ if (skb) {
+ ntx++;
+ ret = dm9051_single_tx(db, skb->data, skb->len);
+ dev_kfree_skb(skb);
+ if (ret < 0)
+ return 0;
+ ndev->stats.tx_bytes += skb->len;
+ ndev->stats.tx_packets++;
+ }
+
+ if (netif_queue_stopped(ndev) &&
+ (skb_queue_len(&db->txq) < DM9051_TX_QUE_LO_WATER))
+ netif_wake_queue(ndev);
+ }
+ return ntx;
+}
+
+/* end with enable the interrupt mask
+ */
+static irqreturn_t dm9051_rx_threaded_irq(int irq, void *pw)
+{
+ struct board_info *db = pw;
+ int result, resul_tx;
+
+ mutex_lock(&db->spi_lock); /* mutex essential */
+ if (netif_carrier_ok(db->ndev)) {
+ result = dm9051_map_write(db, DM9051_IMR, IMR_PAR); /* disable imr */
+ if (result < 0)
+ goto spi_err;
+
+ do {
+ result = dm9051_loop_rx(db); /* threaded irq rx */
+ if (result < 0)
+ goto spi_err;
+ resul_tx = dm9051_loop_tx(db); /* more tx better performance */
+ if (resul_tx < 0)
+ goto spi_err;
+ } while (result > 0);
+
+ result = dm9051_map_write(db, DM9051_IMR, db->imr_all); /* enable imr */
+ if (result < 0)
+ goto spi_err;
+ }
+spi_err:
+ mutex_unlock(&db->spi_lock); /* mutex essential */
+ return IRQ_HANDLED;
+}
+
+static void dm9051_tx_delay(struct kthread_work *ws)
+{
+ struct board_info *db = container_of(ws, struct board_info, kw_tx);
+ int result;
+
+ mutex_lock(&db->spi_lock); /* mutex essential */
+ result = dm9051_loop_tx(db);
+ if (result < 0)
+ netdev_err(db->ndev, "transmit packet error\n");
+ mutex_unlock(&db->spi_lock); /* mutex essential */
+}
+
+static void dm9051_rxctl_delay(struct kthread_work *ws)
+{
+ struct board_info *db = container_of(ws, struct board_info, kw_rxctrl);
+ struct net_device *ndev = db->ndev;
+ int i, result, oft;
+
+ mutex_lock(&db->spi_lock);
+ /* these registers can't write by inblk, must write one by one
+ */
+ for (i = 0; i < ETH_ALEN; i++) {
+ result = dm9051_map_write(db, DM9051_PAR + i, ndev->dev_addr[i]);
+ if (result < 0)
+ goto spi_err;
+ }
+
+ /* these registers can't write by inblk, must write one by one
+ */
+ for (oft = DM9051_MAR, i = 0; i < 4; i++) {
+ result = dm9051_map_write(db, oft++, db->hash_table[i]);
+ if (result < 0)
+ goto spi_err;
+ result = dm9051_map_write(db, oft++, db->hash_table[i] >> 8);
+ if (result < 0)
+ goto spi_err;
+ }
+
+ dm9051_map_write(db, DM9051_RCR, db->rcr_all); /* rx enable */
+spi_err:
+ mutex_unlock(&db->spi_lock);
+}
+
+static int dm9051_map_phyup(struct board_info *db)
+{
+ int ret;
+
+ /* ~BMCR_PDOWN to power-up phyxcer
+ */
+ ret = dm9051_map_phy_updbits(db, MII_BMCR, BMCR_PDOWN, 0);
+ if (ret < 0)
+ return ret;
+
+ /* chip internal operation need wait 1 ms for if GPR power-up phy
+ */
+ ret = dm9051_map_write(db, DM9051_GPR, 0);
+ if (ret < 0)
+ return ret;
+ mdelay(1);
+
+ return 0;
+}
+
+static int dm9051_map_phydown(struct board_info *db)
+{
+ return dm9051_map_write(db, DM9051_GPR, GPR_PHY_ON); /* Power-Down PHY */
+}
+
+static int dm9051_all_start(struct board_info *db)
+{
+ int ret;
+
+ ret = dm9051_map_phyup(db);
+ if (ret < 0)
+ return ret;
+ ret = dm9051_direct_reset_code(db);
+ if (ret < 0)
+ return ret;
+ return dm9051_map_write(db, DM9051_IMR, db->imr_all); /* phyup, rxp to 0xc00 */
+}
+
+static int dm9051_all_stop(struct board_info *db)
+{
+ int ret;
+
+ ret = dm9051_map_phydown(db);
+ if (ret < 0)
+ return ret;
+
+ return dm9051_map_write(db, DM9051_RCR, RCR_RX_DISABLE); /* rx disable */
+}
+
+/* Open network device
+ * Called when the network device is marked active, such as a user executing
+ * 'ifconfig up' on the device
+ */
+static int dm9051_open(struct net_device *ndev)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ struct spi_device *spi = db->spidev;
+ int ret;
+
+ netif_wake_queue(ndev);
+
+ ndev->irq = spi->irq; /* by dts */
+ ret = request_threaded_irq(spi->irq, NULL, dm9051_rx_threaded_irq,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ ndev->name, db);
+ if (ret < 0) {
+ netdev_err(ndev, "failed to get irq\n");
+ return ret;
+ }
+
+ db->imr_all = IMR_PAR | IMR_PRM;
+ db->rcr_all = RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN;
+ db->lcr_all = LMCR_MODE1;
+
+ /* init pause param FlowCtrl */
+ db->eth_pause.rx_pause = true;
+ db->eth_pause.tx_pause = true;
+ db->eth_pause.autoneg = AUTONEG_ENABLE;
+
+ /* We may have start with auto negotiation */
+ db->phydev->autoneg = AUTONEG_ENABLE;
+ db->phydev->speed = 0;
+ db->phydev->duplex = 0;
+
+ ret = dm9051_all_start(db);
+ if (ret < 0) {
+ free_irq(spi->irq, db);
+ netif_stop_queue(ndev);
+ return ret;
+ }
+
+ phy_support_sym_pause(db->phydev); /* Enable support of sym pause */
+ phy_start(db->phydev); /* it enclose with mutex_lock/mutex_unlock */
+ return 0;
+}
+
+/* Close network device
+ * Called to close down a network device which has been active. Cancel any
+ * work, shutdown the RX and TX process and then place the chip into a low
+ * power state while it is not being used
+ */
+static int dm9051_stop(struct net_device *ndev)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+
+ free_irq(db->spidev->irq, db);
+ netif_stop_queue(ndev);
+
+ phy_stop(db->phydev);
+ return dm9051_all_stop(db);
+}
+
+/* event: play a schedule starter in condition
+ */
+static netdev_tx_t dm9051_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+
+ skb_queue_tail(&db->txq, skb); /* add to skb */
+ if (skb_queue_len(&db->txq) > DM9051_TX_QUE_HI_WATER)
+ netif_stop_queue(ndev); /* enforce limit queue size */
+ kthread_queue_work(&db->kw, &db->kw_tx);
+ return NETDEV_TX_OK;
+}
+
+/* event: play with a schedule starter
+ */
+static void dm9051_set_multicast_list_schedule(struct net_device *ndev)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ u8 rcr = RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN;
+ struct netdev_hw_addr *ha;
+ u32 hash_val;
+
+ /* rx control */
+ if (ndev->flags & IFF_PROMISC) {
+ rcr |= RCR_PRMSC;
+ netdev_dbg(ndev, "set_multicast rcr |= RCR_PRMSC, rcr= %02x\n", rcr);
+ }
+
+ if (ndev->flags & IFF_ALLMULTI) {
+ rcr |= RCR_ALL;
+ netdev_dbg(ndev, "set_multicast rcr |= RCR_ALLMULTI, rcr= %02x\n", rcr);
+ }
+
+ db->rcr_all = rcr;
+
+ /* broadcast address */
+ db->hash_table[0] = 0;
+ db->hash_table[1] = 0;
+ db->hash_table[2] = 0;
+ db->hash_table[3] = 0x8000;
+
+ /* the multicast address in Hash Table : 64 bits */
+ netdev_for_each_mc_addr(ha, ndev) {
+ hash_val = ether_crc_le(ETH_ALEN, ha->addr) & 0x3f;
+ db->hash_table[hash_val / 16] |= (u16)1 << (hash_val % 16);
+ }
+
+ kthread_queue_work(&db->kw, &db->kw_rxctrl);
+}
+
+/* event: write into the mac registers and eeprom directly
+ */
+static int dm9051_set_mac_address(struct net_device *ndev, void *p)
+{
+ struct board_info *db = to_dm9051_board(ndev);
+ int i, ret;
+
+ ret = eth_mac_addr(ndev, p);
+ if (ret < 0)
+ return ret;
+
+ /* these registers can't write by outblk, must write one by one
+ */
+ for (i = 0; i < ETH_ALEN; i++)
+ dm9051_map_write(db, DM9051_PAR + i, ndev->dev_addr[i]);
+ return ret;
+}
+
+/* netdev-ops
+ */
+static const struct of_device_id dm9051_match_table[] = {
+ { .compatible = "davicom,dm9051", },
+ {}
+};
+
+static const struct spi_device_id dm9051_id_table[] = {
+ { "dm9051", 0 },
+ {}
+};
+
+static
+const struct net_device_ops dm9051_netdev_ops = {
+ .ndo_open = dm9051_open,
+ .ndo_stop = dm9051_stop,
+ .ndo_start_xmit = dm9051_start_xmit,
+ .ndo_set_rx_mode = dm9051_set_multicast_list_schedule,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = dm9051_set_mac_address,
+};
+
+/* probe subs
+ */
+static void dm9051_operation_clear(struct board_info *db)
+{
+ db->bc.status_err_counter = 0;
+ db->bc.large_err_counter = 0;
+ db->bc.DO_FIFO_RST_counter = 0;
+}
+
+static void dm9051_netdev(struct net_device *ndev)
+{
+ ndev->mtu = 1500;
+ ndev->if_port = IF_PORT_100BASET;
+ ndev->netdev_ops = &dm9051_netdev_ops;
+ ndev->ethtool_ops = &dm9051_ethtool_ops;
+}
+
+static int devm_regmap_init_dm9051(struct spi_device *spi, struct board_info *db)
+{
+ regconfig.lock_arg = db; /* regmap lock/unlock essential */
+
+ db->regmap = devm_regmap_init_spi(db->spidev, ®config);
+
+ if (IS_ERR(db->regmap))
+ return PTR_ERR(db->regmap);
+ return 0;
+}
+
+static int dm9051_register_mdiobus(struct board_info *db)
+{
+ struct spi_device *spi = db->spidev;
+ int ret;
+
+ db->mdiobus = devm_mdiobus_alloc(&spi->dev);
+ if (!db->mdiobus)
+ return -ENOMEM;
+
+ db->mdiobus->priv = db;
+ db->mdiobus->read = dm9051_mdiobus_read;
+ db->mdiobus->write = dm9051_mdiobus_write;
+ db->mdiobus->name = "dm9051-mdiobus";
+ db->mdiobus->phy_mask = (u32)~BIT(1);
+ db->mdiobus->parent = &spi->dev;
+ snprintf(db->mdiobus->id, MII_BUS_ID_SIZE,
+ "dm9051-%s.%u", dev_name(&spi->dev), spi->chip_select);
+
+ ret = devm_mdiobus_register(&spi->dev, db->mdiobus);
+ if (ret < 0) {
+ dev_err(&spi->dev, "Could not register MDIO bus\n");
+ return ret;
+ }
+ return 0;
+}
+
+static int devm_phymap_init_dm9051(struct spi_device *spi, struct board_info *db)
+{
+ struct mdio_device mdiodev;
+
+ mdiodev.dev = spi->dev;
+ mdiodev.bus = db->mdiobus;
+ db->phymap = devm_regmap_init_mdio(&mdiodev, &phyconfig);
+
+ if (IS_ERR(db->phymap))
+ return PTR_ERR(db->phymap);
+ return 0;
+}
+
+static int dm9051_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct net_device *ndev;
+ struct board_info *db;
+ int ret = 0;
+
+ ndev = devm_alloc_etherdev(dev, sizeof(struct board_info));
+ if (!ndev)
+ return -ENOMEM;
+
+ SET_NETDEV_DEV(ndev, dev);
+ dev_set_drvdata(dev, ndev);
+ db = netdev_priv(ndev);
+ db->msg_enable = 0;
+ db->spidev = spi;
+ db->ndev = ndev;
+ dm9051_netdev(ndev);
+
+ kthread_init_worker(&db->kw);
+ kthread_init_work(&db->kw_rxctrl, dm9051_rxctl_delay);
+ kthread_init_work(&db->kw_tx, dm9051_tx_delay);
+
+ db->kwr_task_kw = kthread_run(kthread_worker_fn, &db->kw, "dm9051");
+ if (IS_ERR(db->kwr_task_kw))
+ return PTR_ERR(db->kwr_task_kw);
+
+ mutex_init(&db->spi_lock);
+ mutex_init(&db->reg_mutex);
+
+ ret = devm_regmap_init_dm9051(spi, db);
+ if (ret)
+ goto err_stopthread;
+
+ ret = dm9051_map_chipid(db);
+ if (ret)
+ goto err_stopthread;
+
+ ret = dm9051_map_init_macaddr(ndev, db);
+ if (ret < 0)
+ goto err_stopthread;
+
+ ret = dm9051_register_mdiobus(db);
+ if (ret)
+ goto err_stopthread;
+
+ ret = devm_phymap_init_dm9051(spi, db);
+ if (ret)
+ goto err_stopthread;
+
+ ret = dm9051_phy_connect(db); /* phy connect as poll mode */
+ if (ret)
+ goto err_stopthread;
+
+ dm9051_operation_clear(db);
+ ret = devm_register_netdev(dev, ndev);
+ if (ret) {
+ dev_err(dev, "failed to register network device\n");
+ goto err_netdev;
+ }
+
+ skb_queue_head_init(&db->txq);
+
+ return 0;
+
+err_netdev:
+ phy_disconnect(db->phydev);
+err_stopthread:
+ kthread_stop(db->kwr_task_kw);
+ return ret;
+}
+
+static int dm9051_drv_remove(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct net_device *ndev = dev_get_drvdata(dev);
+ struct board_info *db = to_dm9051_board(ndev);
+
+ phy_disconnect(db->phydev);
+ kthread_stop(db->kwr_task_kw);
+ return 0;
+}
+
+static struct spi_driver dm9051_driver = {
+ .driver = {
+ .name = DRVNAME_9051,
+ .of_match_table = dm9051_match_table,
+ },
+ .probe = dm9051_probe,
+ .remove = dm9051_drv_remove,
+ .id_table = dm9051_id_table,
+};
+module_spi_driver(dm9051_driver);
+
+MODULE_AUTHOR("Joseph CHANG <joseph_chang@davicom.com.tw>");
+MODULE_DESCRIPTION("Davicom DM9051 network SPI driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/davicom/dm9051.h b/drivers/net/ethernet/davicom/dm9051.h
new file mode 100644
index 000000000000..fa396ececc07
--- /dev/null
+++ b/drivers/net/ethernet/davicom/dm9051.h
@@ -0,0 +1,198 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2021 Davicom Semiconductor,Inc.
+ * Davicom DM9051 SPI Fast Ethernet Linux driver
+ */
+
+#ifndef _DM9051_H_
+#define _DM9051_H_
+
+#include <linux/bitfield.h>
+#include <linux/mutex.h>
+#include <linux/netdevice.h>
+#include <linux/types.h>
+
+#define DRVNAME_9051 "dm9051"
+
+#define DM9051_ID 0x9051
+
+#define DM9051_NCR 0x00
+#define DM9051_NSR 0x01
+#define DM9051_TCR 0x02
+#define DM9051_RCR 0x05
+#define DM9051_BPTR 0x08
+#define DM9051_FCR 0x0A
+#define DM9051_EPCR 0x0B
+#define DM9051_EPAR 0x0C
+#define DM9051_EPDRL 0x0D
+#define DM9051_EPDRH 0x0E
+#define DM9051_PAR 0x10
+#define DM9051_MAR 0x16
+#define DM9051_GPCR 0x1E
+#define DM9051_GPR 0x1F
+
+#define DM9051_PIDL 0x2A
+#define DM9051_PIDH 0x2B
+#define DM9051_SMCR 0x2F
+#define DM9051_ATCR 0x30
+#define DM9051_SPIBCR 0x38
+#define DM9051_INTCR 0x39
+#define DM9051_PPCR 0x3D
+
+#define DM9051_MPCR 0x55
+#define DM9051_LMCR 0x57
+#define DM9051_MBNDRY 0x5E
+
+#define DM9051_MRRL 0x74
+#define DM9051_MRRH 0x75
+#define DM9051_MWRL 0x7A
+#define DM9051_MWRH 0x7B
+#define DM9051_TXPLL 0x7C
+#define DM9051_TXPLH 0x7D
+#define DM9051_ISR 0x7E
+#define DM9051_IMR 0x7F
+
+#define DM_SPI_MRCMDX 0x70
+#define DM_SPI_MRCMD 0x72
+#define DM_SPI_MWCMD 0x78
+
+#define DM_SPI_WR 0x80
+
+/* dm9051 Ethernet
+ */
+/* 0x00 */
+#define NCR_WAKEEN BIT(6)
+#define NCR_FDX BIT(3)
+#define NCR_RST BIT(0)
+/* 0x01 */
+#define NSR_SPEED BIT(7)
+#define NSR_LINKST BIT(6)
+#define NSR_WAKEST BIT(5)
+#define NSR_TX2END BIT(3)
+#define NSR_TX1END BIT(2)
+/* 0x02 */
+#define TCR_DIS_JABBER_TIMER BIT(6) /* for Jabber Packet support */
+#define TCR_TXREQ BIT(0)
+/* 0x05 */
+#define RCR_DIS_WATCHDOG_TIMER BIT(6) /* for Jabber Packet support */
+#define RCR_DIS_LONG BIT(5)
+#define RCR_DIS_CRC BIT(4)
+#define RCR_ALL BIT(3)
+#define RCR_PRMSC BIT(1)
+#define RCR_RXEN BIT(0)
+#define RCR_RX_DISABLE (RCR_DIS_LONG | RCR_DIS_CRC)
+/* 0x06 */
+#define RSR_RF BIT(7)
+#define RSR_MF BIT(6)
+#define RSR_LCS BIT(5)
+#define RSR_RWTO BIT(4)
+#define RSR_PLE BIT(3)
+#define RSR_AE BIT(2)
+#define RSR_CE BIT(1)
+#define RSR_FOE BIT(0)
+#define RSR_ERR_BITS (RSR_RF | RSR_LCS | RSR_RWTO | RSR_PLE | \
+ RSR_AE | RSR_CE | RSR_FOE)
+/* 0x0A */
+#define FCR_TXPEN BIT(5)
+#define FCR_BKPM BIT(3)
+#define FCR_FLCE BIT(0)
+#define FCR_RXTX_ENABLE (FCR_TXPEN | FCR_BKPM | FCR_FLCE)
+/* 0x0B */
+#define EPCR_WEP BIT(4)
+#define EPCR_EPOS BIT(3)
+#define EPCR_ERPRR BIT(2)
+#define EPCR_ERPRW BIT(1)
+#define EPCR_ERRE BIT(0)
+/* 0x1E */
+#define GPCR_GEP_CNTL BIT(0)
+/* 0x1F */
+#define GPR_PHY_ON BIT(0)
+/* 0x30 */
+#define ATCR_AUTO_TX BIT(7)
+/* 0x39 */
+#define INTCR_POL_LOW BIT(0)
+#define INTCR_POL_HIGH (0 << 0)
+/* 0x3D */
+/* Pause Packet Control Register - default = 1 */
+#define PPCR_PAUSE_COUNT 0x08
+/* 0x55 */
+#define MPCR_RSTTX BIT(1)
+#define MPCR_RSTRX BIT(0)
+/* 0x57 */
+/* LEDMode Control Register - LEDMode1 */
+/* Value 0x81 : bit[7] = 1, bit[2] = 0, bit[1:0] = 01b */
+#define LMCR_NEWMOD BIT(7)
+#define LMCR_TYPED1 BIT(1)
+#define LMCR_TYPED0 BIT(0)
+#define LMCR_MODE1 (LMCR_NEWMOD | LMCR_TYPED0)
+/* 0x5E */
+#define MBNDRY_BYTE BIT(7)
+/* 0xFE */
+#define ISR_MBS BIT(7)
+#define ISR_ROOS BIT(3)
+#define ISR_ROS BIT(2)
+#define ISR_PTS BIT(1)
+#define ISR_PRS BIT(0)
+#define ISR_CLR_STATUS (ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS)
+/* 0xFF */
+#define IMR_PAR BIT(7)
+#define IMR_LNKCHGI BIT(5)
+#define IMR_PTM BIT(1)
+#define IMR_PRM BIT(0)
+
+/* Const
+ */
+#define DM9051_PHY_ID 1 /* PHY id */
+#define DM9051_PHY 0x40 /* PHY address 0x01 */
+#define DM9051_PKT_RDY 0x01 /* Packet ready to receive */
+#define DM9051_PKT_MAX 1536 /* Received packet max size */
+#define DM9051_TX_QUE_HI_WATER 50
+#define DM9051_TX_QUE_LO_WATER 25
+#define DM_EEPROM_MAGIC 0x9051
+
+static inline struct board_info *to_dm9051_board(struct net_device *ndev)
+{
+ return netdev_priv(ndev);
+}
+
+/* structure definitions
+ */
+struct rx_ctl_mach {
+ u16 status_err_counter; /* 'Status Err' counter */
+ u16 large_err_counter; /* 'Large Err' counter */
+ u16 DO_FIFO_RST_counter; /* 'fifo_reset' counter */
+};
+
+struct dm9051_rxhdr {
+ u8 rxpktready;
+ u8 rxstatus;
+ __le16 rxlen;
+};
+
+struct board_info {
+ struct spi_device *spidev;
+ struct net_device *ndev;
+ struct mii_bus *mdiobus;
+ struct phy_device *phydev;
+ struct sk_buff_head txq;
+ struct mutex spi_lock; /* thread's lock */
+ struct mutex reg_mutex; /* reg access lock */
+ struct regmap *regmap;
+ struct regmap *phymap;
+ struct task_struct *kwr_task_kw;
+ struct kthread_worker kw;
+ struct kthread_work kw_rxctrl;
+ struct kthread_work kw_tx;
+ struct rx_ctl_mach bc;
+ struct dm9051_rxhdr eth_rxhdr;
+ struct ethtool_pauseparam eth_pause;
+ u32 msg_enable;
+ u16 hash_table[4];
+ u8 imr_all;
+ u8 rcr_all;
+ u8 lcr_all;
+};
+
+#define DM_RXHDR_SIZE sizeof(struct dm9051_rxhdr)
+
+#endif /* _DM9051_H_ */
--
2.20.1
^ permalink raw reply related [flat|nested] 5+ messages in thread