[PATCH v2 0/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[PATCH v2 0/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[Stephan Gerhold]

This series adds a simple driver and DT schema for the Awinic AW8738 
audio amplifier. It's fairly simple - the main difference to 
simple-amplifier is that there is a "one-wire pulse control" that 
allows configuring the amplifier to one of a few pre-defined modes. 
This can be used to configure the speaker-guard function (primarily
the power limit for the amplifier).

Jonathan Albrieux (1):
  ASoC: codecs: Add Awinic AW8738 audio amplifier driver

Stephan Gerhold (1):
  ASoC: dt-bindings: Add schema for "awinic,aw8738"

 .../bindings/sound/awinic,aw8738.yaml         |  54 +++++++++
 sound/soc/codecs/Kconfig                      |  10 ++
 sound/soc/codecs/Makefile                     |   2 +
 sound/soc/codecs/aw8738.c                     | 104 ++++++++++++++++++
 4 files changed, 170 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/awinic,aw8738.yaml
 create mode 100644 sound/soc/codecs/aw8738.c

-- 
2.35.1

[PATCH v2 0/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[Stephan Gerhold]

This series adds a simple driver and DT schema for the Awinic AW8738 
audio amplifier. It's fairly simple - the main difference to 
simple-amplifier is that there is a "one-wire pulse control" that 
allows configuring the amplifier to one of a few pre-defined modes. 
This can be used to configure the speaker-guard function (primarily
the power limit for the amplifier).

Jonathan Albrieux (1):
  ASoC: codecs: Add Awinic AW8738 audio amplifier driver

Stephan Gerhold (1):
  ASoC: dt-bindings: Add schema for "awinic,aw8738"

 .../bindings/sound/awinic,aw8738.yaml         |  54 +++++++++
 sound/soc/codecs/Kconfig                      |  10 ++
 sound/soc/codecs/Makefile                     |   2 +
 sound/soc/codecs/aw8738.c                     | 104 ++++++++++++++++++
 4 files changed, 170 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/awinic,aw8738.yaml
 create mode 100644 sound/soc/codecs/aw8738.c

-- 
2.35.1

[PATCH v2 1/2] ASoC: dt-bindings: Add schema for "awinic,aw8738"

[Stephan Gerhold]

Add a DT schema for describing Awinic AW8738 audio amplifiers. They are
fairly simple and controlled using a single GPIO. The number of pulses
during power up selects one of a few pre-defined operation modes. This
can be used to configure the speaker-guard function (primarily the
power limit for the amplifier).

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
Changes in v2:
  - Rename "enable-gpios" -> "mode-gpios" as an attempt to better
    reflect its true purpose. Add description to prevent confusion.
  - Rewrite all descriptions to be more clear about the purpose of
    the amplifier operation modes.
  - Add maximum for "awinic,mode"
---
 .../bindings/sound/awinic,aw8738.yaml         | 54 +++++++++++++++++++
 1 file changed, 54 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/awinic,aw8738.yaml

diff --git a/Documentation/devicetree/bindings/sound/awinic,aw8738.yaml b/Documentation/devicetree/bindings/sound/awinic,aw8738.yaml
new file mode 100644
index 000000000000..dce86dafe382
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/awinic,aw8738.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/awinic,aw8738.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Awinic AW8738 Audio Amplifier
+
+maintainers:
+  - Stephan Gerhold <stephan@gerhold.net>
+
+description:
+  The Awinic AW8738 is a simple audio amplifier with different operation modes
+  (set using one-wire pulse control). The mode configures the speaker-guard
+  function (primarily the power limit for the amplifier).
+
+allOf:
+  - $ref: name-prefix.yaml#
+
+properties:
+  compatible:
+    const: awinic,aw8738
+
+  mode-gpios:
+    description:
+      GPIO used for one-wire pulse control. The pin is typically called SHDN
+      (active-low), but this is misleading since it is actually more than
+      just a simple shutdown/enable control.
+    maxItems: 1
+
+  awinic,mode:
+    description: Operation mode (number of pulses for one-wire pulse control)
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 7
+
+  sound-name-prefix: true
+
+required:
+  - compatible
+  - mode-gpios
+  - awinic,mode
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    audio-amplifier {
+        compatible = "awinic,aw8738";
+        mode-gpios = <&msmgpio 114 GPIO_ACTIVE_HIGH>;
+        awinic,mode = <5>;
+        sound-name-prefix = "Speaker Amp";
+    };
-- 
2.35.1

[PATCH v2 1/2] ASoC: dt-bindings: Add schema for "awinic,aw8738"

[Stephan Gerhold]

Add a DT schema for describing Awinic AW8738 audio amplifiers. They are
fairly simple and controlled using a single GPIO. The number of pulses
during power up selects one of a few pre-defined operation modes. This
can be used to configure the speaker-guard function (primarily the
power limit for the amplifier).

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
Changes in v2:
  - Rename "enable-gpios" -> "mode-gpios" as an attempt to better
    reflect its true purpose. Add description to prevent confusion.
  - Rewrite all descriptions to be more clear about the purpose of
    the amplifier operation modes.
  - Add maximum for "awinic,mode"
---
 .../bindings/sound/awinic,aw8738.yaml         | 54 +++++++++++++++++++
 1 file changed, 54 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/awinic,aw8738.yaml

diff --git a/Documentation/devicetree/bindings/sound/awinic,aw8738.yaml b/Documentation/devicetree/bindings/sound/awinic,aw8738.yaml
new file mode 100644
index 000000000000..dce86dafe382
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/awinic,aw8738.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/awinic,aw8738.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Awinic AW8738 Audio Amplifier
+
+maintainers:
+  - Stephan Gerhold <stephan@gerhold.net>
+
+description:
+  The Awinic AW8738 is a simple audio amplifier with different operation modes
+  (set using one-wire pulse control). The mode configures the speaker-guard
+  function (primarily the power limit for the amplifier).
+
+allOf:
+  - $ref: name-prefix.yaml#
+
+properties:
+  compatible:
+    const: awinic,aw8738
+
+  mode-gpios:
+    description:
+      GPIO used for one-wire pulse control. The pin is typically called SHDN
+      (active-low), but this is misleading since it is actually more than
+      just a simple shutdown/enable control.
+    maxItems: 1
+
+  awinic,mode:
+    description: Operation mode (number of pulses for one-wire pulse control)
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 1
+    maximum: 7
+
+  sound-name-prefix: true
+
+required:
+  - compatible
+  - mode-gpios
+  - awinic,mode
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    audio-amplifier {
+        compatible = "awinic,aw8738";
+        mode-gpios = <&msmgpio 114 GPIO_ACTIVE_HIGH>;
+        awinic,mode = <5>;
+        sound-name-prefix = "Speaker Amp";
+    };
-- 
2.35.1

[PATCH v2 2/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[Stephan Gerhold]

From: Jonathan Albrieux <jonathan.albrieux@gmail.com>

The Awinic AW8738 is a simple audio amplifier using a single GPIO.
The main difference to simple-amplifier is that there is a "one-wire
pulse control" that allows configuring the amplifier to one of a few
pre-defined modes. This can be used to configure the speaker-guard
function (primarily the power limit for the amplifier).

Add a simple driver that allows setting it up in the device tree
with a specified mode number.

Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
Changes in v2:
  - Clarify purpose of operation modes in commit message.
  - Rename "enable" GPIO -> "mode" GPIO to better reflect its true
    purpose.
---
 sound/soc/codecs/Kconfig  |  10 ++++
 sound/soc/codecs/Makefile |   2 +
 sound/soc/codecs/aw8738.c | 104 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 116 insertions(+)
 create mode 100644 sound/soc/codecs/aw8738.c

diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index 4de029ae377c..f46a22660103 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -53,6 +53,7 @@ config SND_SOC_ALL_CODECS
 	imply SND_SOC_AK5558
 	imply SND_SOC_ALC5623
 	imply SND_SOC_ALC5632
+	imply SND_SOC_AW8738
 	imply SND_SOC_BT_SCO
 	imply SND_SOC_BD28623
 	imply SND_SOC_CQ0093VC
@@ -579,6 +580,15 @@ config SND_SOC_ALC5632
 	tristate
 	depends on I2C
 
+config SND_SOC_AW8738
+	tristate "Awinic AW8738 Audio Amplifier"
+	select GPIOLIB
+	help
+	  Enable support for the Awinic AW8738 audio amplifier (or similar).
+	  The driver supports simple audio amplifiers similar to
+	  SND_SOC_SIMPLE_AMPLIFIER, but additionally allows setting the
+	  operation mode using the Awinic-specific one-wire pulse control.
+
 config SND_SOC_BD28623
 	tristate "ROHM BD28623 CODEC"
 	help
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index c3c6059a5f8a..8637e9e869e3 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -45,6 +45,7 @@ snd-soc-ak4671-objs := ak4671.o
 snd-soc-ak5386-objs := ak5386.o
 snd-soc-ak5558-objs := ak5558.o
 snd-soc-arizona-objs := arizona.o arizona-jack.o
+snd-soc-aw8738-objs := aw8738.o
 snd-soc-bd28623-objs := bd28623.o
 snd-soc-bt-sco-objs := bt-sco.o
 snd-soc-cpcap-objs := cpcap.o
@@ -388,6 +389,7 @@ obj-$(CONFIG_SND_SOC_AK5558)	+= snd-soc-ak5558.o
 obj-$(CONFIG_SND_SOC_ALC5623)    += snd-soc-alc5623.o
 obj-$(CONFIG_SND_SOC_ALC5632)	+= snd-soc-alc5632.o
 obj-$(CONFIG_SND_SOC_ARIZONA)	+= snd-soc-arizona.o
+obj-$(CONFIG_SND_SOC_AW8738)	+= snd-soc-aw8738.o
 obj-$(CONFIG_SND_SOC_BD28623)	+= snd-soc-bd28623.o
 obj-$(CONFIG_SND_SOC_BT_SCO)	+= snd-soc-bt-sco.o
 obj-$(CONFIG_SND_SOC_CQ0093VC) += snd-soc-cq93vc.o
diff --git a/sound/soc/codecs/aw8738.c b/sound/soc/codecs/aw8738.c
new file mode 100644
index 000000000000..0fe8af160319
--- /dev/null
+++ b/sound/soc/codecs/aw8738.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+#include <sound/soc.h>
+
+struct aw8738_priv {
+	struct gpio_desc *gpiod_mode;
+	unsigned int mode;
+};
+
+static int aw8738_drv_event(struct snd_soc_dapm_widget *w,
+			    struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *c = snd_soc_dapm_to_component(w->dapm);
+	struct aw8738_priv *aw = snd_soc_component_get_drvdata(c);
+	int i;
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMU:
+		for (i = 0; i < aw->mode; i++) {
+			gpiod_set_value_cansleep(aw->gpiod_mode, 0);
+			udelay(2);
+			gpiod_set_value_cansleep(aw->gpiod_mode, 1);
+			udelay(2);
+		}
+		msleep(40);
+		break;
+	case SND_SOC_DAPM_PRE_PMD:
+		gpiod_set_value_cansleep(aw->gpiod_mode, 0);
+		usleep_range(1000, 2000);
+		break;
+	default:
+		WARN(1, "Unexpected event");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct snd_soc_dapm_widget aw8738_dapm_widgets[] = {
+	SND_SOC_DAPM_INPUT("IN"),
+	SND_SOC_DAPM_OUT_DRV_E("DRV", SND_SOC_NOPM, 0, 0, NULL, 0, aw8738_drv_event,
+			       SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
+	SND_SOC_DAPM_OUTPUT("OUT"),
+};
+
+static const struct snd_soc_dapm_route aw8738_dapm_routes[] = {
+	{ "DRV", NULL, "IN" },
+	{ "OUT", NULL, "DRV" },
+};
+
+static const struct snd_soc_component_driver aw8738_component_driver = {
+	.dapm_widgets = aw8738_dapm_widgets,
+	.num_dapm_widgets = ARRAY_SIZE(aw8738_dapm_widgets),
+	.dapm_routes = aw8738_dapm_routes,
+	.num_dapm_routes = ARRAY_SIZE(aw8738_dapm_routes),
+};
+
+static int aw8738_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct aw8738_priv *aw;
+	int ret;
+
+	aw = devm_kzalloc(dev, sizeof(*aw), GFP_KERNEL);
+	if (!aw)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, aw);
+
+	aw->gpiod_mode = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(aw->gpiod_mode))
+		return dev_err_probe(dev, PTR_ERR(aw->gpiod_mode),
+				     "Failed to get 'mode' gpio");
+
+	ret = device_property_read_u32(dev, "awinic,mode", &aw->mode);
+	if (ret)
+		return -EINVAL;
+
+	return devm_snd_soc_register_component(&pdev->dev,
+					       &aw8738_component_driver,
+					       NULL, 0);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id aw8738_of_match[] = {
+	{ .compatible = "awinic,aw8738" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, aw8738_of_match);
+#endif
+
+static struct platform_driver aw8738_driver = {
+	.probe	= aw8738_probe,
+	.driver = {
+		.name = "aw8738",
+		.of_match_table = of_match_ptr(aw8738_of_match),
+	},
+};
+module_platform_driver(aw8738_driver);
+
+MODULE_DESCRIPTION("Awinic AW8738 Amplifier Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.35.1

[PATCH v2 2/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[Stephan Gerhold]

From: Jonathan Albrieux <jonathan.albrieux@gmail.com>

The Awinic AW8738 is a simple audio amplifier using a single GPIO.
The main difference to simple-amplifier is that there is a "one-wire
pulse control" that allows configuring the amplifier to one of a few
pre-defined modes. This can be used to configure the speaker-guard
function (primarily the power limit for the amplifier).

Add a simple driver that allows setting it up in the device tree
with a specified mode number.

Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
---
Changes in v2:
  - Clarify purpose of operation modes in commit message.
  - Rename "enable" GPIO -> "mode" GPIO to better reflect its true
    purpose.
---
 sound/soc/codecs/Kconfig  |  10 ++++
 sound/soc/codecs/Makefile |   2 +
 sound/soc/codecs/aw8738.c | 104 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 116 insertions(+)
 create mode 100644 sound/soc/codecs/aw8738.c

diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index 4de029ae377c..f46a22660103 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -53,6 +53,7 @@ config SND_SOC_ALL_CODECS
 	imply SND_SOC_AK5558
 	imply SND_SOC_ALC5623
 	imply SND_SOC_ALC5632
+	imply SND_SOC_AW8738
 	imply SND_SOC_BT_SCO
 	imply SND_SOC_BD28623
 	imply SND_SOC_CQ0093VC
@@ -579,6 +580,15 @@ config SND_SOC_ALC5632
 	tristate
 	depends on I2C
 
+config SND_SOC_AW8738
+	tristate "Awinic AW8738 Audio Amplifier"
+	select GPIOLIB
+	help
+	  Enable support for the Awinic AW8738 audio amplifier (or similar).
+	  The driver supports simple audio amplifiers similar to
+	  SND_SOC_SIMPLE_AMPLIFIER, but additionally allows setting the
+	  operation mode using the Awinic-specific one-wire pulse control.
+
 config SND_SOC_BD28623
 	tristate "ROHM BD28623 CODEC"
 	help
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index c3c6059a5f8a..8637e9e869e3 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -45,6 +45,7 @@ snd-soc-ak4671-objs := ak4671.o
 snd-soc-ak5386-objs := ak5386.o
 snd-soc-ak5558-objs := ak5558.o
 snd-soc-arizona-objs := arizona.o arizona-jack.o
+snd-soc-aw8738-objs := aw8738.o
 snd-soc-bd28623-objs := bd28623.o
 snd-soc-bt-sco-objs := bt-sco.o
 snd-soc-cpcap-objs := cpcap.o
@@ -388,6 +389,7 @@ obj-$(CONFIG_SND_SOC_AK5558)	+= snd-soc-ak5558.o
 obj-$(CONFIG_SND_SOC_ALC5623)    += snd-soc-alc5623.o
 obj-$(CONFIG_SND_SOC_ALC5632)	+= snd-soc-alc5632.o
 obj-$(CONFIG_SND_SOC_ARIZONA)	+= snd-soc-arizona.o
+obj-$(CONFIG_SND_SOC_AW8738)	+= snd-soc-aw8738.o
 obj-$(CONFIG_SND_SOC_BD28623)	+= snd-soc-bd28623.o
 obj-$(CONFIG_SND_SOC_BT_SCO)	+= snd-soc-bt-sco.o
 obj-$(CONFIG_SND_SOC_CQ0093VC) += snd-soc-cq93vc.o
diff --git a/sound/soc/codecs/aw8738.c b/sound/soc/codecs/aw8738.c
new file mode 100644
index 000000000000..0fe8af160319
--- /dev/null
+++ b/sound/soc/codecs/aw8738.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+#include <sound/soc.h>
+
+struct aw8738_priv {
+	struct gpio_desc *gpiod_mode;
+	unsigned int mode;
+};
+
+static int aw8738_drv_event(struct snd_soc_dapm_widget *w,
+			    struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *c = snd_soc_dapm_to_component(w->dapm);
+	struct aw8738_priv *aw = snd_soc_component_get_drvdata(c);
+	int i;
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMU:
+		for (i = 0; i < aw->mode; i++) {
+			gpiod_set_value_cansleep(aw->gpiod_mode, 0);
+			udelay(2);
+			gpiod_set_value_cansleep(aw->gpiod_mode, 1);
+			udelay(2);
+		}
+		msleep(40);
+		break;
+	case SND_SOC_DAPM_PRE_PMD:
+		gpiod_set_value_cansleep(aw->gpiod_mode, 0);
+		usleep_range(1000, 2000);
+		break;
+	default:
+		WARN(1, "Unexpected event");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct snd_soc_dapm_widget aw8738_dapm_widgets[] = {
+	SND_SOC_DAPM_INPUT("IN"),
+	SND_SOC_DAPM_OUT_DRV_E("DRV", SND_SOC_NOPM, 0, 0, NULL, 0, aw8738_drv_event,
+			       SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
+	SND_SOC_DAPM_OUTPUT("OUT"),
+};
+
+static const struct snd_soc_dapm_route aw8738_dapm_routes[] = {
+	{ "DRV", NULL, "IN" },
+	{ "OUT", NULL, "DRV" },
+};
+
+static const struct snd_soc_component_driver aw8738_component_driver = {
+	.dapm_widgets = aw8738_dapm_widgets,
+	.num_dapm_widgets = ARRAY_SIZE(aw8738_dapm_widgets),
+	.dapm_routes = aw8738_dapm_routes,
+	.num_dapm_routes = ARRAY_SIZE(aw8738_dapm_routes),
+};
+
+static int aw8738_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct aw8738_priv *aw;
+	int ret;
+
+	aw = devm_kzalloc(dev, sizeof(*aw), GFP_KERNEL);
+	if (!aw)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, aw);
+
+	aw->gpiod_mode = devm_gpiod_get(dev, "mode", GPIOD_OUT_LOW);
+	if (IS_ERR(aw->gpiod_mode))
+		return dev_err_probe(dev, PTR_ERR(aw->gpiod_mode),
+				     "Failed to get 'mode' gpio");
+
+	ret = device_property_read_u32(dev, "awinic,mode", &aw->mode);
+	if (ret)
+		return -EINVAL;
+
+	return devm_snd_soc_register_component(&pdev->dev,
+					       &aw8738_component_driver,
+					       NULL, 0);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id aw8738_of_match[] = {
+	{ .compatible = "awinic,aw8738" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, aw8738_of_match);
+#endif
+
+static struct platform_driver aw8738_driver = {
+	.probe	= aw8738_probe,
+	.driver = {
+		.name = "aw8738",
+		.of_match_table = of_match_ptr(aw8738_of_match),
+	},
+};
+module_platform_driver(aw8738_driver);
+
+MODULE_DESCRIPTION("Awinic AW8738 Amplifier Driver");
+MODULE_LICENSE("GPL v2");
-- 
2.35.1

Re: [PATCH v2 0/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[Mark Brown]

On Fri, 4 Mar 2022 11:24:50 +0100, Stephan Gerhold wrote:
> This series adds a simple driver and DT schema for the Awinic AW8738
> audio amplifier. It's fairly simple - the main difference to
> simple-amplifier is that there is a "one-wire pulse control" that
> allows configuring the amplifier to one of a few pre-defined modes.
> This can be used to configure the speaker-guard function (primarily
> the power limit for the amplifier).
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/2] ASoC: dt-bindings: Add schema for "awinic,aw8738"
      commit: b3284430615c27ca441967f99fbde957b434e092
[2/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver
      commit: fc14fac286a05d36202f8114d00a9935ca2e0756

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

Re: [PATCH v2 0/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver

[Mark Brown]

On Fri, 4 Mar 2022 11:24:50 +0100, Stephan Gerhold wrote:
> This series adds a simple driver and DT schema for the Awinic AW8738
> audio amplifier. It's fairly simple - the main difference to
> simple-amplifier is that there is a "one-wire pulse control" that
> allows configuring the amplifier to one of a few pre-defined modes.
> This can be used to configure the speaker-guard function (primarily
> the power limit for the amplifier).
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/2] ASoC: dt-bindings: Add schema for "awinic,aw8738"
      commit: b3284430615c27ca441967f99fbde957b434e092
[2/2] ASoC: codecs: Add Awinic AW8738 audio amplifier driver
      commit: fc14fac286a05d36202f8114d00a9935ca2e0756

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark