* [PATCH v2 0/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi all,
This series introduces basic support for the Radxa ROCK3 Model A
featuring the Rockchip RK3568 SoC. The basic support includes Ethernet,
USB2 and the headphone connector.
Patch 3 adds support for the Video Output Processor (VOP) 2 and the
HDMI output. It requires the VOP2/HDMI TX patches (which are discussed
on the list) and can be considered as RFC.
v2 adds the missing entry in the Makefile and Rob's Acked-by: on the
dt-bindings patch.
Looking forward to your comments!
Best regards,
Michael
Michael Riesch (3):
dt-bindings: arm: rockchip: add radxa rock3 model a
arm64: dts: rockchip: add basic dts for the radxa rock3 model a
arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
.../devicetree/bindings/arm/rockchip.yaml | 5 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3a.dts | 548 ++++++++++++++++++
3 files changed, 554 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
--
2.30.2
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 0/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi all,
This series introduces basic support for the Radxa ROCK3 Model A
featuring the Rockchip RK3568 SoC. The basic support includes Ethernet,
USB2 and the headphone connector.
Patch 3 adds support for the Video Output Processor (VOP) 2 and the
HDMI output. It requires the VOP2/HDMI TX patches (which are discussed
on the list) and can be considered as RFC.
v2 adds the missing entry in the Makefile and Rob's Acked-by: on the
dt-bindings patch.
Looking forward to your comments!
Best regards,
Michael
Michael Riesch (3):
dt-bindings: arm: rockchip: add radxa rock3 model a
arm64: dts: rockchip: add basic dts for the radxa rock3 model a
arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
.../devicetree/bindings/arm/rockchip.yaml | 5 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3a.dts | 548 ++++++++++++++++++
3 files changed, 554 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
--
2.30.2
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 0/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi all,
This series introduces basic support for the Radxa ROCK3 Model A
featuring the Rockchip RK3568 SoC. The basic support includes Ethernet,
USB2 and the headphone connector.
Patch 3 adds support for the Video Output Processor (VOP) 2 and the
HDMI output. It requires the VOP2/HDMI TX patches (which are discussed
on the list) and can be considered as RFC.
v2 adds the missing entry in the Makefile and Rob's Acked-by: on the
dt-bindings patch.
Looking forward to your comments!
Best regards,
Michael
Michael Riesch (3):
dt-bindings: arm: rockchip: add radxa rock3 model a
arm64: dts: rockchip: add basic dts for the radxa rock3 model a
arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
.../devicetree/bindings/arm/rockchip.yaml | 5 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3a.dts | 548 ++++++++++++++++++
3 files changed, 554 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 1/3] dt-bindings: arm: rockchip: add radxa rock3 model a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-03-10 21:03 ` Michael Riesch
-1 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch, Rob Herring
Add entry for the Radxa ROCK3 Model A board (with the Rockchip
RK3568 SoC).
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 4aed16176434..94b1107ba5f2 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -537,6 +537,11 @@ properties:
- const: radxa,rock2-square
- const: rockchip,rk3288
+ - description: Radxa ROCK3 Model A
+ items:
+ - const: radxa,rock3a
+ - const: rockchip,rk3568
+
- description: Rikomagic MK808 v1
items:
- const: rikomagic,mk808
--
2.30.2
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 1/3] dt-bindings: arm: rockchip: add radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch, Rob Herring
Add entry for the Radxa ROCK3 Model A board (with the Rockchip
RK3568 SoC).
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 4aed16176434..94b1107ba5f2 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -537,6 +537,11 @@ properties:
- const: radxa,rock2-square
- const: rockchip,rk3288
+ - description: Radxa ROCK3 Model A
+ items:
+ - const: radxa,rock3a
+ - const: rockchip,rk3568
+
- description: Rikomagic MK808 v1
items:
- const: rikomagic,mk808
--
2.30.2
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 1/3] dt-bindings: arm: rockchip: add radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch, Rob Herring
Add entry for the Radxa ROCK3 Model A board (with the Rockchip
RK3568 SoC).
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 4aed16176434..94b1107ba5f2 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -537,6 +537,11 @@ properties:
- const: radxa,rock2-square
- const: rockchip,rk3288
+ - description: Radxa ROCK3 Model A
+ items:
+ - const: radxa,rock3a
+ - const: rockchip,rk3568
+
- description: Rikomagic MK808 v1
items:
- const: rikomagic,mk808
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-03-10 21:03 ` Michael Riesch
-1 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Add basic device tree for the Radxa ROCK3 Model A board (with
the Rockchip RK3568 SoC) including Ethernet, USB2 and headphone
connector.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3a.dts | 501 ++++++++++++++++++
2 files changed, 502 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 479906f3ad7b..5fc9cf98473e 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -58,3 +58,4 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
new file mode 100644
index 000000000000..18d2d8e5e693
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -0,0 +1,501 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "Radxa ROCK3 Model A";
+ compatible = "radxa,rock3a", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_user: led-0 {
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_BLUE>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_user_en>;
+ };
+ };
+
+ rk809-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+
+ vcc12v_dcin: vcc12v-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb_host: vcc5v0-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb_host_en>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+
+ codec {
+ mic-in-differential;
+ };
+ };
+};
+
+&i2s1_8ch {
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_phy_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ ethernet {
+ eth_phy_rst: eth_phy_rst {
+ rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ led_user_en: led_user_en {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic_int {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
--
2.30.2
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Add basic device tree for the Radxa ROCK3 Model A board (with
the Rockchip RK3568 SoC) including Ethernet, USB2 and headphone
connector.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3a.dts | 501 ++++++++++++++++++
2 files changed, 502 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 479906f3ad7b..5fc9cf98473e 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -58,3 +58,4 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
new file mode 100644
index 000000000000..18d2d8e5e693
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -0,0 +1,501 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "Radxa ROCK3 Model A";
+ compatible = "radxa,rock3a", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_user: led-0 {
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_BLUE>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_user_en>;
+ };
+ };
+
+ rk809-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+
+ vcc12v_dcin: vcc12v-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb_host: vcc5v0-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb_host_en>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+
+ codec {
+ mic-in-differential;
+ };
+ };
+};
+
+&i2s1_8ch {
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_phy_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ ethernet {
+ eth_phy_rst: eth_phy_rst {
+ rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ led_user_en: led_user_en {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic_int {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
--
2.30.2
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Add basic device tree for the Radxa ROCK3 Model A board (with
the Rockchip RK3568 SoC) including Ethernet, USB2 and headphone
connector.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3a.dts | 501 ++++++++++++++++++
2 files changed, 502 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 479906f3ad7b..5fc9cf98473e 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -58,3 +58,4 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
new file mode 100644
index 000000000000..18d2d8e5e693
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -0,0 +1,501 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "Radxa ROCK3 Model A";
+ compatible = "radxa,rock3a", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_user: led-0 {
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_BLUE>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_user_en>;
+ };
+ };
+
+ rk809-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+
+ vcc12v_dcin: vcc12v-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_usb_host: vcc5v0-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb_host_en>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+
+ codec {
+ mic-in-differential;
+ };
+ };
+};
+
+&i2s1_8ch {
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_phy_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ ethernet {
+ eth_phy_rst: eth_phy_rst {
+ rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ led_user_en: led_user_en {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic_int {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-03-10 21:03 ` Michael Riesch
-1 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Enable the RK356x Video Output Processor (VOP) 2 on the Radxa
ROCK3 Model A.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
.../boot/dts/rockchip/rk3568-rock-3a.dts | 47 +++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
index 18d2d8e5e693..e568ce377055 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -4,6 +4,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
#include "rk3568.dtsi"
/ {
@@ -20,6 +21,17 @@ chosen: chosen {
stdout-path = "serial2:1500000n8";
};
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -134,6 +146,24 @@ &gpu {
status = "okay";
};
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
status = "okay";
@@ -499,3 +529,20 @@ &usb2phy1_otg {
phy-supply = <&vcc5v0_usb_host>;
status = "okay";
};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.30.2
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Enable the RK356x Video Output Processor (VOP) 2 on the Radxa
ROCK3 Model A.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
.../boot/dts/rockchip/rk3568-rock-3a.dts | 47 +++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
index 18d2d8e5e693..e568ce377055 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -4,6 +4,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
#include "rk3568.dtsi"
/ {
@@ -20,6 +21,17 @@ chosen: chosen {
stdout-path = "serial2:1500000n8";
};
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -134,6 +146,24 @@ &gpu {
status = "okay";
};
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
status = "okay";
@@ -499,3 +529,20 @@ &usb2phy1_otg {
phy-supply = <&vcc5v0_usb_host>;
status = "okay";
};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.30.2
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
@ 2022-03-10 21:03 ` Michael Riesch
0 siblings, 0 replies; 24+ messages in thread
From: Michael Riesch @ 2022-03-10 21:03 UTC (permalink / raw)
To: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
Cc: Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Enable the RK356x Video Output Processor (VOP) 2 on the Radxa
ROCK3 Model A.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
.../boot/dts/rockchip/rk3568-rock-3a.dts | 47 +++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
index 18d2d8e5e693..e568ce377055 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -4,6 +4,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
#include "rk3568.dtsi"
/ {
@@ -20,6 +21,17 @@ chosen: chosen {
stdout-path = "serial2:1500000n8";
};
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -134,6 +146,24 @@ &gpu {
status = "okay";
};
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
status = "okay";
@@ -499,3 +529,20 @@ &usb2phy1_otg {
phy-supply = <&vcc5v0_usb_host>;
status = "okay";
};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.30.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-03-11 10:17 ` kernel test robot
-1 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 10:17 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: kbuild-all, Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-buildonly-randconfig-r002-20220310 (https://download.01.org/0day-ci/archive/20220311/202203111851.n5LAS0gw-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:7:10: fatal error: dt-bindings/soc/rockchip,vop2.h: No such file or directory
7 | #include <dt-bindings/soc/rockchip,vop2.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
vim +7 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
2
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/leds/common.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
> 7 #include <dt-bindings/soc/rockchip,vop2.h>
8 #include "rk3568.dtsi"
9
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
@ 2022-03-11 10:17 ` kernel test robot
0 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 10:17 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: kbuild-all, Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-buildonly-randconfig-r002-20220310 (https://download.01.org/0day-ci/archive/20220311/202203111851.n5LAS0gw-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:7:10: fatal error: dt-bindings/soc/rockchip,vop2.h: No such file or directory
7 | #include <dt-bindings/soc/rockchip,vop2.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
vim +7 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
2
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/leds/common.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
> 7 #include <dt-bindings/soc/rockchip,vop2.h>
8 #include "rk3568.dtsi"
9
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
@ 2022-03-11 10:17 ` kernel test robot
0 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 10:17 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: kbuild-all, Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-buildonly-randconfig-r002-20220310 (https://download.01.org/0day-ci/archive/20220311/202203111851.n5LAS0gw-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:7:10: fatal error: dt-bindings/soc/rockchip,vop2.h: No such file or directory
7 | #include <dt-bindings/soc/rockchip,vop2.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
vim +7 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
2
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/leds/common.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
> 7 #include <dt-bindings/soc/rockchip,vop2.h>
8 #include "rk3568.dtsi"
9
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-03-11 16:57 ` kernel test robot
-1 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 16:57 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: llvm, kbuild-all, Rob Herring, Heiko Stuebner, Levin Du,
Tianling Shen, Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen,
Peter Geis, Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next keystone/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-randconfig-r014-20220310 (https://download.01.org/0day-ci/archive/20220312/202203120049.YIR5IFdM-lkp@intel.com/config)
compiler: clang version 15.0.0 (https://github.com/llvm/llvm-project 276ca87382b8f16a65bddac700202924228982f6)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# https://github.com/0day-ci/linux/commit/c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:7:10: fatal error: 'dt-bindings/soc/rockchip,vop2.h' file not found
#include <dt-bindings/soc/rockchip,vop2.h>
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
vim +7 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
2
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/leds/common.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
> 7 #include <dt-bindings/soc/rockchip,vop2.h>
8 #include "rk3568.dtsi"
9
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
@ 2022-03-11 16:57 ` kernel test robot
0 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 16:57 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: llvm, kbuild-all, Rob Herring, Heiko Stuebner, Levin Du,
Tianling Shen, Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen,
Peter Geis, Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next keystone/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-randconfig-r014-20220310 (https://download.01.org/0day-ci/archive/20220312/202203120049.YIR5IFdM-lkp@intel.com/config)
compiler: clang version 15.0.0 (https://github.com/llvm/llvm-project 276ca87382b8f16a65bddac700202924228982f6)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# https://github.com/0day-ci/linux/commit/c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:7:10: fatal error: 'dt-bindings/soc/rockchip,vop2.h' file not found
#include <dt-bindings/soc/rockchip,vop2.h>
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
vim +7 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
2
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/leds/common.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
> 7 #include <dt-bindings/soc/rockchip,vop2.h>
8 #include "rk3568.dtsi"
9
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a
@ 2022-03-11 16:57 ` kernel test robot
0 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 16:57 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: llvm, kbuild-all, Rob Herring, Heiko Stuebner, Levin Du,
Tianling Shen, Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen,
Peter Geis, Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next keystone/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-randconfig-r014-20220310 (https://download.01.org/0day-ci/archive/20220312/202203120049.YIR5IFdM-lkp@intel.com/config)
compiler: clang version 15.0.0 (https://github.com/llvm/llvm-project 276ca87382b8f16a65bddac700202924228982f6)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# https://github.com/0day-ci/linux/commit/c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:7:10: fatal error: 'dt-bindings/soc/rockchip,vop2.h' file not found
#include <dt-bindings/soc/rockchip,vop2.h>
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 error generated.
vim +7 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
2
3 /dts-v1/;
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/leds/common.h>
6 #include <dt-bindings/pinctrl/rockchip.h>
> 7 #include <dt-bindings/soc/rockchip,vop2.h>
8 #include "rk3568.dtsi"
9
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-03-11 21:50 ` kernel test robot
-1 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 21:50 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: kbuild-all, Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next keystone/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-buildonly-randconfig-r002-20220310 (https://download.01.org/0day-ci/archive/20220312/202203120525.muN78AQX-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/8d0dad8b66056847b8a2e95272ee74ca4b12fd29
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout 8d0dad8b66056847b8a2e95272ee74ca4b12fd29
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
Note: the linux-review/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612 HEAD c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f builds fine.
It only hurts bisectability.
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:132.1-5 Label or path gpu not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:473.1-16 Label or path usb_host0_ehci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:477.1-16 Label or path usb_host0_ohci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:481.1-16 Label or path usb_host1_ehci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:485.1-16 Label or path usb_host1_ohci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:489.1-10 Label or path usb2phy1 not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:493.1-15 Label or path usb2phy1_host not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:498.1-14 Label or path usb2phy1_otg not found
>> FATAL ERROR: Syntax error parsing input tree
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-11 21:50 ` kernel test robot
0 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 21:50 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: kbuild-all, Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next keystone/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-buildonly-randconfig-r002-20220310 (https://download.01.org/0day-ci/archive/20220312/202203120525.muN78AQX-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/8d0dad8b66056847b8a2e95272ee74ca4b12fd29
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout 8d0dad8b66056847b8a2e95272ee74ca4b12fd29
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
Note: the linux-review/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612 HEAD c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f builds fine.
It only hurts bisectability.
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:132.1-5 Label or path gpu not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:473.1-16 Label or path usb_host0_ehci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:477.1-16 Label or path usb_host0_ohci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:481.1-16 Label or path usb_host1_ehci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:485.1-16 Label or path usb_host1_ohci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:489.1-10 Label or path usb2phy1 not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:493.1-15 Label or path usb2phy1_host not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:498.1-14 Label or path usb2phy1_otg not found
>> FATAL ERROR: Syntax error parsing input tree
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-03-11 21:50 ` kernel test robot
0 siblings, 0 replies; 24+ messages in thread
From: kernel test robot @ 2022-03-11 21:50 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-arm-kernel, linux-rockchip,
linux-kernel
Cc: kbuild-all, Rob Herring, Heiko Stuebner, Levin Du, Tianling Shen,
Chen-Yu Tsai, Sascha Hauer, Alex Bee, Liang Chen, Peter Geis,
Michael Riesch
Hi Michael,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on arm/for-next xilinx-xlnx/master arm64/for-next/core shawnguo/for-next clk/clk-next kvmarm/next keystone/next v5.17-rc7]
[cannot apply to rockchip/for-next soc/for-next next-20220310]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-buildonly-randconfig-r002-20220310 (https://download.01.org/0day-ci/archive/20220312/202203120525.muN78AQX-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/8d0dad8b66056847b8a2e95272ee74ca4b12fd29
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612
git checkout 8d0dad8b66056847b8a2e95272ee74ca4b12fd29
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
Note: the linux-review/Michael-Riesch/arm64-dts-rockchip-add-basic-dts-for-the-radxa-rock3-model-a/20220311-050612 HEAD c217f194b7a9cbdb7cbb8149ae1f6e8c2faf6e3f builds fine.
It only hurts bisectability.
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:132.1-5 Label or path gpu not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:473.1-16 Label or path usb_host0_ehci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:477.1-16 Label or path usb_host0_ohci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:481.1-16 Label or path usb_host1_ehci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:485.1-16 Label or path usb_host1_ohci not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:489.1-10 Label or path usb2phy1 not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:493.1-15 Label or path usb2phy1_host not found
>> Error: arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts:498.1-14 Label or path usb2phy1_otg not found
>> FATAL ERROR: Syntax error parsing input tree
---
0-DAY CI Kernel Test Service
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 0/3] (partial) arm64: dts: rockchip: add basic dts for the radxa rock3 model a
2022-03-10 21:03 ` Michael Riesch
(?)
@ 2022-04-04 9:00 ` Heiko Stuebner
-1 siblings, 0 replies; 24+ messages in thread
From: Heiko Stuebner @ 2022-04-04 9:00 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-rockchip, linux-kernel,
linux-arm-kernel
Cc: Heiko Stuebner, Sascha Hauer, Peter Geis, Tianling Shen,
Rob Herring, Levin Du, Liang Chen, Alex Bee, Chen-Yu Tsai
On Thu, 10 Mar 2022 22:03:49 +0100, Michael Riesch wrote:
> This series introduces basic support for the Radxa ROCK3 Model A
> featuring the Rockchip RK3568 SoC. The basic support includes Ethernet,
> USB2 and the headphone connector.
>
> Patch 3 adds support for the Video Output Processor (VOP) 2 and the
> HDMI output. It requires the VOP2/HDMI TX patches (which are discussed
> on the list) and can be considered as RFC.
>
> [...]
(partial) Applied, thanks!
[1/3] dt-bindings: arm: rockchip: add radxa rock3 model a
commit: 65a31b5abb7f4c373ce0de52eca75348156c87d2
[2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
commit: 056ef970c434a572f81eae199846bf3f521a8303
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 0/3] (partial) arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-04-04 9:00 ` Heiko Stuebner
0 siblings, 0 replies; 24+ messages in thread
From: Heiko Stuebner @ 2022-04-04 9:00 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-rockchip, linux-kernel,
linux-arm-kernel
Cc: Heiko Stuebner, Sascha Hauer, Peter Geis, Tianling Shen,
Rob Herring, Levin Du, Liang Chen, Alex Bee, Chen-Yu Tsai
On Thu, 10 Mar 2022 22:03:49 +0100, Michael Riesch wrote:
> This series introduces basic support for the Radxa ROCK3 Model A
> featuring the Rockchip RK3568 SoC. The basic support includes Ethernet,
> USB2 and the headphone connector.
>
> Patch 3 adds support for the Video Output Processor (VOP) 2 and the
> HDMI output. It requires the VOP2/HDMI TX patches (which are discussed
> on the list) and can be considered as RFC.
>
> [...]
(partial) Applied, thanks!
[1/3] dt-bindings: arm: rockchip: add radxa rock3 model a
commit: 65a31b5abb7f4c373ce0de52eca75348156c87d2
[2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
commit: 056ef970c434a572f81eae199846bf3f521a8303
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 0/3] (partial) arm64: dts: rockchip: add basic dts for the radxa rock3 model a
@ 2022-04-04 9:00 ` Heiko Stuebner
0 siblings, 0 replies; 24+ messages in thread
From: Heiko Stuebner @ 2022-04-04 9:00 UTC (permalink / raw)
To: Michael Riesch, devicetree, linux-rockchip, linux-kernel,
linux-arm-kernel
Cc: Heiko Stuebner, Sascha Hauer, Peter Geis, Tianling Shen,
Rob Herring, Levin Du, Liang Chen, Alex Bee, Chen-Yu Tsai
On Thu, 10 Mar 2022 22:03:49 +0100, Michael Riesch wrote:
> This series introduces basic support for the Radxa ROCK3 Model A
> featuring the Rockchip RK3568 SoC. The basic support includes Ethernet,
> USB2 and the headphone connector.
>
> Patch 3 adds support for the Video Output Processor (VOP) 2 and the
> HDMI output. It requires the VOP2/HDMI TX patches (which are discussed
> on the list) and can be considered as RFC.
>
> [...]
(partial) Applied, thanks!
[1/3] dt-bindings: arm: rockchip: add radxa rock3 model a
commit: 65a31b5abb7f4c373ce0de52eca75348156c87d2
[2/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a
commit: 056ef970c434a572f81eae199846bf3f521a8303
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2022-04-04 9:02 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-03-10 21:03 [PATCH v2 0/3] arm64: dts: rockchip: add basic dts for the radxa rock3 model a Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-10 21:03 ` [PATCH v2 1/3] dt-bindings: arm: rockchip: add " Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-10 21:03 ` [PATCH v2 2/3] arm64: dts: rockchip: add basic dts for the " Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-11 21:50 ` kernel test robot
2022-03-11 21:50 ` kernel test robot
2022-03-11 21:50 ` kernel test robot
2022-03-10 21:03 ` [PATCH v2 3/3] arm64: dts: rockchip: enable vop2 and hdmi tx on rock-3a Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-10 21:03 ` Michael Riesch
2022-03-11 10:17 ` kernel test robot
2022-03-11 10:17 ` kernel test robot
2022-03-11 10:17 ` kernel test robot
2022-03-11 16:57 ` kernel test robot
2022-03-11 16:57 ` kernel test robot
2022-03-11 16:57 ` kernel test robot
2022-04-04 9:00 ` [PATCH v2 0/3] (partial) arm64: dts: rockchip: add basic dts for the radxa rock3 model a Heiko Stuebner
2022-04-04 9:00 ` Heiko Stuebner
2022-04-04 9:00 ` Heiko Stuebner
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.