* [PATCH 0/2] arm64: ti: k3-am62: Introduce DT nodes for basic peripherals
@ 2022-04-15 13:19 ` Vignesh Raghavendra
0 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-15 13:19 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
Add nodes for McSPI, OSPI, MMC, DMA and CPSW eth switch
Bootlog:https://gist.github.com/r-vignesh/b2fb23da7c589394f56ce08fd00a155b
Vignesh Raghavendra (2):
arm64: dts: ti: k3-am62: Add more peripheral nodes
arm64: dts: ti: k3-am625-sk: Enable on board peripherals
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 266 ++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 20 ++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 271 +++++++++++++++++++++++
3 files changed, 557 insertions(+)
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 1/2] arm64: dts: ti: k3-am62: Add more peripheral nodes
2022-04-15 13:19 ` Vignesh Raghavendra
@ 2022-04-15 13:19 ` Vignesh Raghavendra
-1 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-15 13:19 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
Add nodes for McSPI, OSPI, DMA, CPSW, MMC and On Chip SRAM nodes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 266 +++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 20 ++
2 files changed, 286 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index c68472c692f4..4b6ba98dd0a2 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -6,6 +6,14 @@
*/
&cbass_main {
+ oc_sram: sram@70000000 {
+ compatible = "mmio-sram";
+ reg = <0x00 0x70000000 0x00 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x00 0x70000000 0x10000>;
+ };
+
gic500: interrupt-controller@1800000 {
compatible = "arm,gic-v3";
#address-cells = <2>;
@@ -40,6 +48,12 @@ main_conf: syscon@100000 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x00 0x00100000 0x20000>;
+
+ phy_gmii_sel: phy@4044 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4044 0x8>;
+ #phy-cells = <1>;
+ };
};
dmss: bus@48000000 {
@@ -61,6 +75,69 @@ secure_proxy_main: mailbox@4d000000 {
interrupt-names = "rx_012";
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ inta_main_dmss: interrupt-controller@48000000 {
+ compatible = "ti,sci-inta";
+ reg = <0x00 0x48000000 0x00 0x100000>;
+ #interrupt-cells = <0>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ msi-controller;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <28>;
+ ti,interrupt-ranges = <4 68 36>;
+ ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+ };
+
+ main_bcdma: dma-controller@485c0100 {
+ compatible = "ti,am64-dmss-bcdma";
+ reg = <0x00 0x485c0100 0x00 0x100>,
+ <0x00 0x4c000000 0x00 0x20000>,
+ <0x00 0x4a820000 0x00 0x20000>,
+ <0x00 0x4aa40000 0x00 0x20000>,
+ <0x00 0x4bc00000 0x00 0x100000>;
+ reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <3>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <26>;
+ ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+ ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+ ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+ };
+
+ main_pktdma: dma-controller@485c0000 {
+ compatible = "ti,am64-dmss-pktdma";
+ reg = <0x00 0x485c0000 0x00 0x100>,
+ <0x00 0x4a800000 0x00 0x20000>,
+ <0x00 0x4aa00000 0x00 0x40000>,
+ <0x00 0x4b800000 0x00 0x400000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <2>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <30>;
+ ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+ <0x24>, /* CPSW_TX_CHAN */
+ <0x25>, /* SAUL_TX_0_CHAN */
+ <0x26>; /* SAUL_TX_1_CHAN */
+ ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+ <0x11>, /* RING_CPSW_TX_CHAN */
+ <0x12>, /* RING_SAUL_TX_0_CHAN */
+ <0x13>; /* RING_SAUL_TX_1_CHAN */
+ ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+ <0x2b>, /* CPSW_RX_CHAN */
+ <0x2d>, /* SAUL_RX_0_CHAN */
+ <0x2f>, /* SAUL_RX_1_CHAN */
+ <0x31>, /* SAUL_RX_2_CHAN */
+ <0x33>; /* SAUL_RX_3_CHAN */
+ ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+ <0x2c>, /* FLOW_CPSW_RX_CHAN */
+ <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+ <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
+ };
};
dmsc: system-controller@44043000 {
@@ -203,6 +280,36 @@ main_i2c3: i2c@20030000 {
clock-names = "fck";
};
+ main_spi0: spi@20100000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x20100000 0x00 0x400>;
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 172 0>;
+ };
+
+ main_spi1: spi@20110000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20110000 0x00 0x400>;
+ interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 173 0>;
+ };
+
+ main_spi2: spi@20120000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20120000 0x00 0x400>;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 174 0>;
+ };
+
main_gpio_intr: interrupt-controller@a00000 {
compatible = "ti,sci-intr";
reg = <0x00 0x00a00000 0x00 0x800>;
@@ -249,6 +356,165 @@ main_gpio1: gpio@601000 {
clock-names = "gpio";
};
+ sdhci0: mmc@fa10000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa10000 0x00 0x1000>, <0x00 0x0fa18000 0x00 0x400>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 57 5>, <&k3_clks 57 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ assigned-clocks = <&k3_clks 57 6>;
+ assigned-clock-parents = <&k3_clks 57 8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ ti,trm-icp = <0x2>;
+ bus-width = <8>;
+ ti,clkbuf-sel = <0x7>;
+ ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-mmc-hs = <0x0>;
+ ti,otap-del-sel-ddr52 = <0x9>;
+ ti,otap-del-sel-hs200 = <0x6>;
+ };
+
+ sdhci1: mmc@fa00000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa00000 0x00 0x1000>, <0x00 0x0fa08000 0x00 0x400>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ ti,trm-icp = <0x2>;
+ ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-sd-hs = <0x0>;
+ ti,otap-del-sel-sdr12 = <0xf>;
+ ti,otap-del-sel-sdr25 = <0xf>;
+ ti,otap-del-sel-sdr50 = <0xc>;
+ ti,otap-del-sel-sdr104 = <0x6>;
+ ti,otap-del-sel-ddr50 = <0x9>;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ bus-width = <4>;
+ };
+
+ sdhci2: mmc@fa20000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa20000 0x00 0x1000>, <0x00 0x0fa28000 0x00 0x400>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ ti,trm-icp = <0x2>;
+ ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-sd-hs = <0x0>;
+ ti,otap-del-sel-sdr12 = <0xf>;
+ ti,otap-del-sel-sdr25 = <0xf>;
+ ti,otap-del-sel-sdr50 = <0xc>;
+ ti,otap-del-sel-sdr104 = <0x6>;
+ ti,otap-del-sel-ddr50 = <0x9>;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ };
+
+ fss: bus@fc00000 {
+ compatible = "simple-bus";
+ reg = <0x00 0x0fc00000 0x00 0x70000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ospi0: spi@fc40000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x0fc40000 0x00 0x100>,
+ <0x05 0x00000000 0x01 0x00000000>;
+ interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 75 7>;
+ assigned-clocks = <&k3_clks 75 7>;
+ assigned-clock-parents = <&k3_clks 75 8>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cpsw3g: ethernet@8000000 {
+ compatible = "ti,am642-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x00 0x08000000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0x08000000 0x00 0x200000>;
+ clocks = <&k3_clks 13 0>;
+ assigned-clocks = <&k3_clks 13 3>;
+ assigned-clock-parents = <&k3_clks 13 11>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_pktdma 0xc600 15>,
+ <&main_pktdma 0xc601 15>,
+ <&main_pktdma 0xc602 15>,
+ <&main_pktdma 0xc603 15>,
+ <&main_pktdma 0xc604 15>,
+ <&main_pktdma 0xc605 15>,
+ <&main_pktdma 0xc606 15>,
+ <&main_pktdma 0xc607 15>,
+ <&main_pktdma 0x4600 15>;
+ dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+ "tx7", "rx";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ phys = <&phy_gmii_sel 1>;
+ mac-address = [00 00 00 00 00 00];
+ ti,syscon-efuse = <&wkup_conf 0x200>;
+ };
+
+ cpsw_port2: port@2 {
+ reg = <2>;
+ ti,mac-only;
+ label = "port2";
+ phys = <&phy_gmii_sel 2>;
+ mac-address = [00 00 00 00 00 00];
+ };
+ };
+
+ cpsw3g_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 13 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 13 1>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
hwspinlock: spinlock@2a000000 {
compatible = "ti,am64-hwspinlock";
reg = <0x00 0x2a000000 0x00 0x1000>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
index 9d210d55fc71..d103824c963f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
@@ -33,4 +33,24 @@ mcu_i2c0: i2c@4900000 {
clocks = <&k3_clks 106 2>;
clock-names = "fck";
};
+
+ mcu_spi0: spi@4b00000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x04b00000 0x00 0x400>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 147 0>;
+ };
+
+ mcu_spi1: spi@4b10000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x04b10000 0x00 0x400>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 148 0>;
+ };
};
--
2.35.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 1/2] arm64: dts: ti: k3-am62: Add more peripheral nodes
@ 2022-04-15 13:19 ` Vignesh Raghavendra
0 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-15 13:19 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
Add nodes for McSPI, OSPI, DMA, CPSW, MMC and On Chip SRAM nodes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 266 +++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 20 ++
2 files changed, 286 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index c68472c692f4..4b6ba98dd0a2 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -6,6 +6,14 @@
*/
&cbass_main {
+ oc_sram: sram@70000000 {
+ compatible = "mmio-sram";
+ reg = <0x00 0x70000000 0x00 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x00 0x70000000 0x10000>;
+ };
+
gic500: interrupt-controller@1800000 {
compatible = "arm,gic-v3";
#address-cells = <2>;
@@ -40,6 +48,12 @@ main_conf: syscon@100000 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x00 0x00100000 0x20000>;
+
+ phy_gmii_sel: phy@4044 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4044 0x8>;
+ #phy-cells = <1>;
+ };
};
dmss: bus@48000000 {
@@ -61,6 +75,69 @@ secure_proxy_main: mailbox@4d000000 {
interrupt-names = "rx_012";
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ inta_main_dmss: interrupt-controller@48000000 {
+ compatible = "ti,sci-inta";
+ reg = <0x00 0x48000000 0x00 0x100000>;
+ #interrupt-cells = <0>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ msi-controller;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <28>;
+ ti,interrupt-ranges = <4 68 36>;
+ ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+ };
+
+ main_bcdma: dma-controller@485c0100 {
+ compatible = "ti,am64-dmss-bcdma";
+ reg = <0x00 0x485c0100 0x00 0x100>,
+ <0x00 0x4c000000 0x00 0x20000>,
+ <0x00 0x4a820000 0x00 0x20000>,
+ <0x00 0x4aa40000 0x00 0x20000>,
+ <0x00 0x4bc00000 0x00 0x100000>;
+ reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <3>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <26>;
+ ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+ ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+ ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+ };
+
+ main_pktdma: dma-controller@485c0000 {
+ compatible = "ti,am64-dmss-pktdma";
+ reg = <0x00 0x485c0000 0x00 0x100>,
+ <0x00 0x4a800000 0x00 0x20000>,
+ <0x00 0x4aa00000 0x00 0x40000>,
+ <0x00 0x4b800000 0x00 0x400000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <2>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <30>;
+ ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+ <0x24>, /* CPSW_TX_CHAN */
+ <0x25>, /* SAUL_TX_0_CHAN */
+ <0x26>; /* SAUL_TX_1_CHAN */
+ ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+ <0x11>, /* RING_CPSW_TX_CHAN */
+ <0x12>, /* RING_SAUL_TX_0_CHAN */
+ <0x13>; /* RING_SAUL_TX_1_CHAN */
+ ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+ <0x2b>, /* CPSW_RX_CHAN */
+ <0x2d>, /* SAUL_RX_0_CHAN */
+ <0x2f>, /* SAUL_RX_1_CHAN */
+ <0x31>, /* SAUL_RX_2_CHAN */
+ <0x33>; /* SAUL_RX_3_CHAN */
+ ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+ <0x2c>, /* FLOW_CPSW_RX_CHAN */
+ <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+ <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
+ };
};
dmsc: system-controller@44043000 {
@@ -203,6 +280,36 @@ main_i2c3: i2c@20030000 {
clock-names = "fck";
};
+ main_spi0: spi@20100000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x20100000 0x00 0x400>;
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 172 0>;
+ };
+
+ main_spi1: spi@20110000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20110000 0x00 0x400>;
+ interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 173 0>;
+ };
+
+ main_spi2: spi@20120000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20120000 0x00 0x400>;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 174 0>;
+ };
+
main_gpio_intr: interrupt-controller@a00000 {
compatible = "ti,sci-intr";
reg = <0x00 0x00a00000 0x00 0x800>;
@@ -249,6 +356,165 @@ main_gpio1: gpio@601000 {
clock-names = "gpio";
};
+ sdhci0: mmc@fa10000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa10000 0x00 0x1000>, <0x00 0x0fa18000 0x00 0x400>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 57 5>, <&k3_clks 57 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ assigned-clocks = <&k3_clks 57 6>;
+ assigned-clock-parents = <&k3_clks 57 8>;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ ti,trm-icp = <0x2>;
+ bus-width = <8>;
+ ti,clkbuf-sel = <0x7>;
+ ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-mmc-hs = <0x0>;
+ ti,otap-del-sel-ddr52 = <0x9>;
+ ti,otap-del-sel-hs200 = <0x6>;
+ };
+
+ sdhci1: mmc@fa00000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa00000 0x00 0x1000>, <0x00 0x0fa08000 0x00 0x400>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ ti,trm-icp = <0x2>;
+ ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-sd-hs = <0x0>;
+ ti,otap-del-sel-sdr12 = <0xf>;
+ ti,otap-del-sel-sdr25 = <0xf>;
+ ti,otap-del-sel-sdr50 = <0xc>;
+ ti,otap-del-sel-sdr104 = <0x6>;
+ ti,otap-del-sel-ddr50 = <0x9>;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ bus-width = <4>;
+ };
+
+ sdhci2: mmc@fa20000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa20000 0x00 0x1000>, <0x00 0x0fa28000 0x00 0x400>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ ti,trm-icp = <0x2>;
+ ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-sd-hs = <0x0>;
+ ti,otap-del-sel-sdr12 = <0xf>;
+ ti,otap-del-sel-sdr25 = <0xf>;
+ ti,otap-del-sel-sdr50 = <0xc>;
+ ti,otap-del-sel-sdr104 = <0x6>;
+ ti,otap-del-sel-ddr50 = <0x9>;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ };
+
+ fss: bus@fc00000 {
+ compatible = "simple-bus";
+ reg = <0x00 0x0fc00000 0x00 0x70000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ospi0: spi@fc40000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x0fc40000 0x00 0x100>,
+ <0x05 0x00000000 0x01 0x00000000>;
+ interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 75 7>;
+ assigned-clocks = <&k3_clks 75 7>;
+ assigned-clock-parents = <&k3_clks 75 8>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cpsw3g: ethernet@8000000 {
+ compatible = "ti,am642-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x00 0x08000000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0x08000000 0x00 0x200000>;
+ clocks = <&k3_clks 13 0>;
+ assigned-clocks = <&k3_clks 13 3>;
+ assigned-clock-parents = <&k3_clks 13 11>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_pktdma 0xc600 15>,
+ <&main_pktdma 0xc601 15>,
+ <&main_pktdma 0xc602 15>,
+ <&main_pktdma 0xc603 15>,
+ <&main_pktdma 0xc604 15>,
+ <&main_pktdma 0xc605 15>,
+ <&main_pktdma 0xc606 15>,
+ <&main_pktdma 0xc607 15>,
+ <&main_pktdma 0x4600 15>;
+ dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+ "tx7", "rx";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ phys = <&phy_gmii_sel 1>;
+ mac-address = [00 00 00 00 00 00];
+ ti,syscon-efuse = <&wkup_conf 0x200>;
+ };
+
+ cpsw_port2: port@2 {
+ reg = <2>;
+ ti,mac-only;
+ label = "port2";
+ phys = <&phy_gmii_sel 2>;
+ mac-address = [00 00 00 00 00 00];
+ };
+ };
+
+ cpsw3g_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 13 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 13 1>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
hwspinlock: spinlock@2a000000 {
compatible = "ti,am64-hwspinlock";
reg = <0x00 0x2a000000 0x00 0x1000>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
index 9d210d55fc71..d103824c963f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
@@ -33,4 +33,24 @@ mcu_i2c0: i2c@4900000 {
clocks = <&k3_clks 106 2>;
clock-names = "fck";
};
+
+ mcu_spi0: spi@4b00000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x04b00000 0x00 0x400>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 147 0>;
+ };
+
+ mcu_spi1: spi@4b10000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x04b10000 0x00 0x400>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 148 0>;
+ };
};
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 2/2] arm64: dts: ti: k3-am625-sk: Enable on board peripherals
2022-04-15 13:19 ` Vignesh Raghavendra
@ 2022-04-15 13:19 ` Vignesh Raghavendra
-1 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-15 13:19 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
Add nodes for I2C IO expander, OSPI Flash, Eth PHYs, SD and eMMC that
are present on AM625 SK board.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 271 +++++++++++++++++++++++++
1 file changed, 271 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 0de4113ccd5d..a0ea2cc66b31 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -9,6 +9,7 @@
#include <dt-bindings/leds/common.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
#include "k3-am625.dtsi"
/ {
@@ -17,6 +18,10 @@ / {
aliases {
serial2 = &main_uart0;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ mmc2 = &sdhci2;
+ spi0 = &ospi0;
};
chosen {
@@ -87,6 +92,33 @@ vcc_3v3_sys: regulator-2 {
regulator-boot-on;
};
+ vdd_mmc1: fixed-regulator-sd {
+ /* TPS22918DBVR */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vcc_3v3_sys>;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-TLV71033 {
+ /* Output of TLV71033 */
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vcc_5v0>;
+ gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -124,11 +156,114 @@ AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
>;
};
+ main_i2c2_pins_default: main-i2c2-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
+ AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
+ >;
+ };
+
+ main_mmc0_pins_default: main-mmc0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
+ AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
+ AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
+ AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
+ AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
+ AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
+ AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
+ AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
+ AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
+ AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
+ AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
+ AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
+ AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
+ AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
+ AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
+ >;
+ };
+
usr_led_pins_default: usr-led-pins-default {
pinctrl-single,pins = <
AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
>;
};
+
+ main_mdio1_pins_default: main-mdio1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
+ AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+ >;
+ };
+
+ main_rgmii1_pins_default: main-rgmii1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
+ AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
+ AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
+ AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
+ AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
+ AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
+ AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
+ AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
+ AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
+ AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
+ AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
+ AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
+ >;
+ };
+
+ main_rgmii2_pins_default: main-rgmii2-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
+ AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
+ AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
+ AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
+ AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
+ AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
+ AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
+ AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
+ AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
+ AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
+ AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
+ AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
+ >;
+ };
+
+ ospi0_pins_default: ospi0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
+ AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
+ AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
+ AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
+ AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
+ AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
+ AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
+ AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
+ AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
+ AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
+ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
+ >;
+ };
+
+ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
+ >;
+ };
};
&wkup_uart0 {
@@ -188,6 +323,33 @@ &main_i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c1_pins_default>;
clock-frequency = <400000>;
+
+ exp1: gpio@22 {
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+ "PRU_DETECT", "MMC1_SD_EN",
+ "VPP_LDO_EN", "EXP_PS_3V3_En",
+ "EXP_PS_5V0_En", "EXP_HAT_DETECT",
+ "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
+ "UART1_FET_BUF_EN", "WL_LT_EN",
+ "GPIO_HDMI_RSTn", "CSI_GPIO1",
+ "CSI_GPIO2", "PRU_3V3_EN",
+ "HDMI_INTn", "TEST_GPIO2",
+ "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+ "MCASP1_FET_SEL", "UART1_FET_SEL",
+ "TSINT#", "IO_EXP_TEST_LED";
+
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+ };
};
&main_i2c2 {
@@ -198,9 +360,118 @@ &main_i2c3 {
status = "disabled";
};
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc0_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&sdhci1 {
+ /* SD/MMC */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mdio1_pins_default
+ &main_rgmii1_pins_default
+ &main_rgmii2_pins_default>;
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+
+ cpsw3g_phy1: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
ti,mbox-tx = <1 0 0>;
};
};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ };
+ };
+ };
+};
--
2.35.3
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 2/2] arm64: dts: ti: k3-am625-sk: Enable on board peripherals
@ 2022-04-15 13:19 ` Vignesh Raghavendra
0 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-15 13:19 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
Add nodes for I2C IO expander, OSPI Flash, Eth PHYs, SD and eMMC that
are present on AM625 SK board.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 271 +++++++++++++++++++++++++
1 file changed, 271 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 0de4113ccd5d..a0ea2cc66b31 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -9,6 +9,7 @@
#include <dt-bindings/leds/common.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
#include "k3-am625.dtsi"
/ {
@@ -17,6 +18,10 @@ / {
aliases {
serial2 = &main_uart0;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ mmc2 = &sdhci2;
+ spi0 = &ospi0;
};
chosen {
@@ -87,6 +92,33 @@ vcc_3v3_sys: regulator-2 {
regulator-boot-on;
};
+ vdd_mmc1: fixed-regulator-sd {
+ /* TPS22918DBVR */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vcc_3v3_sys>;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-TLV71033 {
+ /* Output of TLV71033 */
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vcc_5v0>;
+ gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -124,11 +156,114 @@ AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
>;
};
+ main_i2c2_pins_default: main-i2c2-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
+ AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
+ >;
+ };
+
+ main_mmc0_pins_default: main-mmc0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
+ AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+ AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
+ AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
+ AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
+ AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
+ AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
+ AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
+ AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
+ AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
+ AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
+ AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
+ AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
+ AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
+ AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
+ AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
+ >;
+ };
+
usr_led_pins_default: usr-led-pins-default {
pinctrl-single,pins = <
AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
>;
};
+
+ main_mdio1_pins_default: main-mdio1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
+ AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+ >;
+ };
+
+ main_rgmii1_pins_default: main-rgmii1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
+ AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
+ AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
+ AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
+ AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
+ AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
+ AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
+ AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
+ AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
+ AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
+ AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
+ AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
+ >;
+ };
+
+ main_rgmii2_pins_default: main-rgmii2-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
+ AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
+ AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
+ AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
+ AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
+ AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
+ AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
+ AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
+ AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
+ AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
+ AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
+ AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
+ >;
+ };
+
+ ospi0_pins_default: ospi0-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
+ AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
+ AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
+ AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
+ AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
+ AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
+ AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
+ AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
+ AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
+ AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
+ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
+ >;
+ };
+
+ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
+ >;
+ };
};
&wkup_uart0 {
@@ -188,6 +323,33 @@ &main_i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c1_pins_default>;
clock-frequency = <400000>;
+
+ exp1: gpio@22 {
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+ "PRU_DETECT", "MMC1_SD_EN",
+ "VPP_LDO_EN", "EXP_PS_3V3_En",
+ "EXP_PS_5V0_En", "EXP_HAT_DETECT",
+ "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
+ "UART1_FET_BUF_EN", "WL_LT_EN",
+ "GPIO_HDMI_RSTn", "CSI_GPIO1",
+ "CSI_GPIO2", "PRU_3V3_EN",
+ "HDMI_INTn", "TEST_GPIO2",
+ "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+ "MCASP1_FET_SEL", "UART1_FET_SEL",
+ "TSINT#", "IO_EXP_TEST_LED";
+
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+ };
};
&main_i2c2 {
@@ -198,9 +360,118 @@ &main_i2c3 {
status = "disabled";
};
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc0_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&sdhci1 {
+ /* SD/MMC */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mdio1_pins_default
+ &main_rgmii1_pins_default
+ &main_rgmii2_pins_default>;
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+
+ cpsw3g_phy1: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
ti,mbox-tx = <1 0 0>;
};
};
+
+&ospi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ };
+ };
+ };
+};
--
2.35.3
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH 2/2] arm64: dts: ti: k3-am625-sk: Enable on board peripherals
2022-04-15 13:19 ` Vignesh Raghavendra
@ 2022-04-22 6:21 ` Vignesh Raghavendra
-1 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-22 6:21 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
On 15/04/22 6:49 pm, Vignesh Raghavendra wrote:
> Add nodes for I2C IO expander, OSPI Flash, Eth PHYs, SD and eMMC that
> are present on AM625 SK board.
>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 271 +++++++++++++++++++++++++
> 1 file changed, 271 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> index 0de4113ccd5d..a0ea2cc66b31 100644
> --- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> @@ -9,6 +9,7 @@
>
> #include <dt-bindings/leds/common.h>
> #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> #include "k3-am625.dtsi"
>
> / {
> @@ -17,6 +18,10 @@ / {
>
> aliases {
> serial2 = &main_uart0;
> + mmc0 = &sdhci0;
> + mmc1 = &sdhci1;
> + mmc2 = &sdhci2;
> + spi0 = &ospi0;
Grygorii pointed out we are missing ethernet aliases:
ethernet0 = &cpsw_port1;
ethernet0 = &cpsw_port2;
Will send v2 with this update.
> };
>
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [PATCH 2/2] arm64: dts: ti: k3-am625-sk: Enable on board peripherals
@ 2022-04-22 6:21 ` Vignesh Raghavendra
0 siblings, 0 replies; 10+ messages in thread
From: Vignesh Raghavendra @ 2022-04-22 6:21 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Aswath Govindraju, Grygorii Strashko
On 15/04/22 6:49 pm, Vignesh Raghavendra wrote:
> Add nodes for I2C IO expander, OSPI Flash, Eth PHYs, SD and eMMC that
> are present on AM625 SK board.
>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 271 +++++++++++++++++++++++++
> 1 file changed, 271 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> index 0de4113ccd5d..a0ea2cc66b31 100644
> --- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
> @@ -9,6 +9,7 @@
>
> #include <dt-bindings/leds/common.h>
> #include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> #include "k3-am625.dtsi"
>
> / {
> @@ -17,6 +18,10 @@ / {
>
> aliases {
> serial2 = &main_uart0;
> + mmc0 = &sdhci0;
> + mmc1 = &sdhci1;
> + mmc2 = &sdhci2;
> + spi0 = &ospi0;
Grygorii pointed out we are missing ethernet aliases:
ethernet0 = &cpsw_port1;
ethernet0 = &cpsw_port2;
Will send v2 with this update.
> };
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 0/2] arm64: ti: k3-am62: Introduce DT nodes for basic peripherals
2022-04-15 13:19 ` Vignesh Raghavendra
@ 2022-04-19 13:41 ` Bryan Brattlof
-1 siblings, 0 replies; 10+ messages in thread
From: Bryan Brattlof @ 2022-04-19 13:41 UTC (permalink / raw)
To: Vignesh Raghavendra
Cc: Nishanth Menon, Tero Kristo, Rob Herring, Krzysztof Kozlowski,
linux-arm-kernel, devicetree, linux-kernel, Aswath Govindraju,
Grygorii Strashko
On April 15, 2022 thus sayeth Vignesh Raghavendra:
> Add nodes for McSPI, OSPI, MMC, DMA and CPSW eth switch
>
> Bootlog:https://gist.github.com/r-vignesh/b2fb23da7c589394f56ce08fd00a155b
>
> Vignesh Raghavendra (2):
> arm64: dts: ti: k3-am62: Add more peripheral nodes
> arm64: dts: ti: k3-am625-sk: Enable on board peripherals
Looks great to me!
Reviewed-by: Bryan Brattlof <bb@ti.com>
~Bryan
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 0/2] arm64: ti: k3-am62: Introduce DT nodes for basic peripherals
@ 2022-04-19 13:41 ` Bryan Brattlof
0 siblings, 0 replies; 10+ messages in thread
From: Bryan Brattlof @ 2022-04-19 13:41 UTC (permalink / raw)
To: Vignesh Raghavendra
Cc: Nishanth Menon, Tero Kristo, Rob Herring, Krzysztof Kozlowski,
linux-arm-kernel, devicetree, linux-kernel, Aswath Govindraju,
Grygorii Strashko
On April 15, 2022 thus sayeth Vignesh Raghavendra:
> Add nodes for McSPI, OSPI, MMC, DMA and CPSW eth switch
>
> Bootlog:https://gist.github.com/r-vignesh/b2fb23da7c589394f56ce08fd00a155b
>
> Vignesh Raghavendra (2):
> arm64: dts: ti: k3-am62: Add more peripheral nodes
> arm64: dts: ti: k3-am625-sk: Enable on board peripherals
Looks great to me!
Reviewed-by: Bryan Brattlof <bb@ti.com>
~Bryan
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread