* [PATCH 0/3] Enable audio output on AM62-SK
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
This patch series adds support for audio output via headphone jack on the
AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is
connected to McASP (serializer).
The same 3.5mm jack can be used for combined playback+recording, but audio
input is currently disabled on McASP until further testing and debugging.
Please apply this series on top of
https://lore.kernel.org/all/20220415131917.431137-1-vigneshr@ti.com/
Jai Luthra (1):
arm64: dts: ti: am625-sk: Add audio output support
Jayesh Choudhary (2):
arm64: dts: ti: k3-am62-main: Add McASP nodes
ASoC: ti: davinci-mcasp: Add dma-type for bcdma
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
sound/soc/ti/davinci-mcasp.c | 2 +
3 files changed, 142 insertions(+)
--
2.17.1
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 0/3] Enable audio output on AM62-SK
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: devicetree, alsa-devel, Jai Luthra, linux-kernel, linux-arm-kernel
This patch series adds support for audio output via headphone jack on the
AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is
connected to McASP (serializer).
The same 3.5mm jack can be used for combined playback+recording, but audio
input is currently disabled on McASP until further testing and debugging.
Please apply this series on top of
https://lore.kernel.org/all/20220415131917.431137-1-vigneshr@ti.com/
Jai Luthra (1):
arm64: dts: ti: am625-sk: Add audio output support
Jayesh Choudhary (2):
arm64: dts: ti: k3-am62-main: Add McASP nodes
ASoC: ti: davinci-mcasp: Add dma-type for bcdma
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
sound/soc/ti/davinci-mcasp.c | 2 +
3 files changed, 142 insertions(+)
--
2.17.1
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 0/3] Enable audio output on AM62-SK
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
This patch series adds support for audio output via headphone jack on the
AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is
connected to McASP (serializer).
The same 3.5mm jack can be used for combined playback+recording, but audio
input is currently disabled on McASP until further testing and debugging.
Please apply this series on top of
https://lore.kernel.org/all/20220415131917.431137-1-vigneshr@ti.com/
Jai Luthra (1):
arm64: dts: ti: am625-sk: Add audio output support
Jayesh Choudhary (2):
arm64: dts: ti: k3-am62-main: Add McASP nodes
ASoC: ti: davinci-mcasp: Add dma-type for bcdma
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
sound/soc/ti/davinci-mcasp.c | 2 +
3 files changed, 142 insertions(+)
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 1/3] arm64: dts: ti: k3-am62-main: Add McASP nodes
2022-04-21 13:22 ` Jai Luthra
(?)
@ 2022-04-21 13:22 ` Jai Luthra
-1 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
From: Jayesh Choudhary <j-choudhary@ti.com>
Add the nodes for McASP 0-2.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 4b6ba98dd0a2..2014c0ca599c 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -530,4 +530,55 @@
ti,mbox-num-users = <4>;
ti,mbox-num-fifos = <16>;
};
+
+ mcasp0: mcasp@2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp1: mcasp@2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp2: mcasp@2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ };
};
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 1/3] arm64: dts: ti: k3-am62-main: Add McASP nodes
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: devicetree, alsa-devel, Jai Luthra, linux-kernel, linux-arm-kernel
From: Jayesh Choudhary <j-choudhary@ti.com>
Add the nodes for McASP 0-2.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 4b6ba98dd0a2..2014c0ca599c 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -530,4 +530,55 @@
ti,mbox-num-users = <4>;
ti,mbox-num-fifos = <16>;
};
+
+ mcasp0: mcasp@2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp1: mcasp@2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp2: mcasp@2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ };
};
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 1/3] arm64: dts: ti: k3-am62-main: Add McASP nodes
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
From: Jayesh Choudhary <j-choudhary@ti.com>
Add the nodes for McASP 0-2.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 4b6ba98dd0a2..2014c0ca599c 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -530,4 +530,55 @@
ti,mbox-num-users = <4>;
ti,mbox-num-fifos = <16>;
};
+
+ mcasp0: mcasp@2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp1: mcasp@2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp2: mcasp@2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ };
};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 2/3] ASoC: ti: davinci-mcasp: Add dma-type for bcdma
2022-04-21 13:22 ` Jai Luthra
(?)
@ 2022-04-21 13:22 ` Jai Luthra
-1 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
From: Jayesh Choudhary <j-choudhary@ti.com>
Set DMA type for ti-bcdma controller for AM62-SK.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
sound/soc/ti/davinci-mcasp.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/sound/soc/ti/davinci-mcasp.c b/sound/soc/ti/davinci-mcasp.c
index 2c146b91fca3..377be2e2b6ee 100644
--- a/sound/soc/ti/davinci-mcasp.c
+++ b/sound/soc/ti/davinci-mcasp.c
@@ -2047,6 +2047,8 @@ static int davinci_mcasp_get_dma_type(struct davinci_mcasp *mcasp)
return PCM_SDMA;
else if (strstr(tmp, "udmap"))
return PCM_UDMA;
+ else if (strstr(tmp, "bcdma"))
+ return PCM_UDMA;
return PCM_EDMA;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 2/3] ASoC: ti: davinci-mcasp: Add dma-type for bcdma
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
From: Jayesh Choudhary <j-choudhary@ti.com>
Set DMA type for ti-bcdma controller for AM62-SK.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
sound/soc/ti/davinci-mcasp.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/sound/soc/ti/davinci-mcasp.c b/sound/soc/ti/davinci-mcasp.c
index 2c146b91fca3..377be2e2b6ee 100644
--- a/sound/soc/ti/davinci-mcasp.c
+++ b/sound/soc/ti/davinci-mcasp.c
@@ -2047,6 +2047,8 @@ static int davinci_mcasp_get_dma_type(struct davinci_mcasp *mcasp)
return PCM_SDMA;
else if (strstr(tmp, "udmap"))
return PCM_UDMA;
+ else if (strstr(tmp, "bcdma"))
+ return PCM_UDMA;
return PCM_EDMA;
}
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 2/3] ASoC: ti: davinci-mcasp: Add dma-type for bcdma
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: devicetree, alsa-devel, Jai Luthra, linux-kernel, linux-arm-kernel
From: Jayesh Choudhary <j-choudhary@ti.com>
Set DMA type for ti-bcdma controller for AM62-SK.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
sound/soc/ti/davinci-mcasp.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/sound/soc/ti/davinci-mcasp.c b/sound/soc/ti/davinci-mcasp.c
index 2c146b91fca3..377be2e2b6ee 100644
--- a/sound/soc/ti/davinci-mcasp.c
+++ b/sound/soc/ti/davinci-mcasp.c
@@ -2047,6 +2047,8 @@ static int davinci_mcasp_get_dma_type(struct davinci_mcasp *mcasp)
return PCM_SDMA;
else if (strstr(tmp, "udmap"))
return PCM_UDMA;
+ else if (strstr(tmp, "bcdma"))
+ return PCM_UDMA;
return PCM_EDMA;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 3/3] arm64: dts: ti: am625-sk: Add audio output support
2022-04-21 13:22 ` Jai Luthra
(?)
@ 2022-04-21 13:22 ` Jai Luthra
-1 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux. Disable all other McASP nodes.
Audio input is currently not working properly, so the RX port on McASP1
is disabled for now, until the issue is debugged.
The serializer is shared between HDMI and codec. By default codec is
used for output, but it can be toggled to HDMI using a FET switch
connected to the MCASP1_FET_SEL (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index a0ea2cc66b31..414f27d4a9dd 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -119,6 +119,46 @@
<3300000 0x1>;
};
+ vcc_1v8: fixedregulator-vcc-1v8 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ tlv320_mclk: tlv320-mclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -264,6 +304,15 @@
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
+
+ main_mcasp1_pins_default: main-mcasp1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+ AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+ AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+ >;
+ };
};
&wkup_uart0 {
@@ -350,6 +399,18 @@
pinctrl-names = "default";
pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ DVDD-supply = <&vcc_1v8>;
+ };
};
&main_i2c2 {
@@ -410,6 +471,34 @@
};
};
+&mcasp0 {
+ status = "disabled";
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&mcasp2 {
+ status = "disabled";
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 3/3] arm64: dts: ti: am625-sk: Add audio output support
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: alsa-devel, linux-kernel, linux-arm-kernel, devicetree, Jai Luthra
Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux. Disable all other McASP nodes.
Audio input is currently not working properly, so the RX port on McASP1
is disabled for now, until the issue is debugged.
The serializer is shared between HDMI and codec. By default codec is
used for output, but it can be toggled to HDMI using a FET switch
connected to the MCASP1_FET_SEL (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index a0ea2cc66b31..414f27d4a9dd 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -119,6 +119,46 @@
<3300000 0x1>;
};
+ vcc_1v8: fixedregulator-vcc-1v8 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ tlv320_mclk: tlv320-mclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -264,6 +304,15 @@
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
+
+ main_mcasp1_pins_default: main-mcasp1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+ AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+ AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+ >;
+ };
};
&wkup_uart0 {
@@ -350,6 +399,18 @@
pinctrl-names = "default";
pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ DVDD-supply = <&vcc_1v8>;
+ };
};
&main_i2c2 {
@@ -410,6 +471,34 @@
};
};
+&mcasp0 {
+ status = "disabled";
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&mcasp2 {
+ status = "disabled";
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 3/3] arm64: dts: ti: am625-sk: Add audio output support
@ 2022-04-21 13:22 ` Jai Luthra
0 siblings, 0 replies; 15+ messages in thread
From: Jai Luthra @ 2022-04-21 13:22 UTC (permalink / raw)
To: Peter Ujfalusi, Nishanth Menon, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary
Cc: devicetree, alsa-devel, Jai Luthra, linux-kernel, linux-arm-kernel
Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux. Disable all other McASP nodes.
Audio input is currently not working properly, so the RX port on McASP1
is disabled for now, until the issue is debugged.
The serializer is shared between HDMI and codec. By default codec is
used for output, but it can be toggled to HDMI using a FET switch
connected to the MCASP1_FET_SEL (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index a0ea2cc66b31..414f27d4a9dd 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -119,6 +119,46 @@
<3300000 0x1>;
};
+ vcc_1v8: fixedregulator-vcc-1v8 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ tlv320_mclk: tlv320-mclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -264,6 +304,15 @@
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
+
+ main_mcasp1_pins_default: main-mcasp1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+ AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+ AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+ >;
+ };
};
&wkup_uart0 {
@@ -350,6 +399,18 @@
pinctrl-names = "default";
pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ DVDD-supply = <&vcc_1v8>;
+ };
};
&main_i2c2 {
@@ -410,6 +471,34 @@
};
};
+&mcasp0 {
+ status = "disabled";
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&mcasp2 {
+ status = "disabled";
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH 0/3] Enable audio output on AM62-SK
2022-04-21 13:22 ` Jai Luthra
(?)
@ 2022-04-21 13:49 ` Nishanth Menon
-1 siblings, 0 replies; 15+ messages in thread
From: Nishanth Menon @ 2022-04-21 13:49 UTC (permalink / raw)
To: Jai Luthra
Cc: Peter Ujfalusi, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary, alsa-devel, linux-kernel,
linux-arm-kernel, devicetree
On 18:52-20220421, Jai Luthra wrote:
> This patch series adds support for audio output via headphone jack on the
> AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is
> connected to McASP (serializer).
>
> The same 3.5mm jack can be used for combined playback+recording, but audio
> input is currently disabled on McASP until further testing and debugging.
>
> Please apply this series on top of
> https://lore.kernel.org/all/20220415131917.431137-1-vigneshr@ti.com/
>
> Jai Luthra (1):
> arm64: dts: ti: am625-sk: Add audio output support
>
> Jayesh Choudhary (2):
> arm64: dts: ti: k3-am62-main: Add McASP nodes
> ASoC: ti: davinci-mcasp: Add dma-type for bcdma
>
> arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++
> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
> sound/soc/ti/davinci-mcasp.c | 2 +
> 3 files changed, 142 insertions(+)
>
Please split this series up. Send out the sound/soc/ti/davinci-mcasp.c patch as it's own.
dts changes are their own series.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 0/3] Enable audio output on AM62-SK
@ 2022-04-21 13:49 ` Nishanth Menon
0 siblings, 0 replies; 15+ messages in thread
From: Nishanth Menon @ 2022-04-21 13:49 UTC (permalink / raw)
To: Jai Luthra
Cc: Peter Ujfalusi, Vignesh Raghavendra, Rob Herring,
Krzysztof Kozlowski, Jayesh Choudhary, alsa-devel, linux-kernel,
linux-arm-kernel, devicetree
On 18:52-20220421, Jai Luthra wrote:
> This patch series adds support for audio output via headphone jack on the
> AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is
> connected to McASP (serializer).
>
> The same 3.5mm jack can be used for combined playback+recording, but audio
> input is currently disabled on McASP until further testing and debugging.
>
> Please apply this series on top of
> https://lore.kernel.org/all/20220415131917.431137-1-vigneshr@ti.com/
>
> Jai Luthra (1):
> arm64: dts: ti: am625-sk: Add audio output support
>
> Jayesh Choudhary (2):
> arm64: dts: ti: k3-am62-main: Add McASP nodes
> ASoC: ti: davinci-mcasp: Add dma-type for bcdma
>
> arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++
> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
> sound/soc/ti/davinci-mcasp.c | 2 +
> 3 files changed, 142 insertions(+)
>
Please split this series up. Send out the sound/soc/ti/davinci-mcasp.c patch as it's own.
dts changes are their own series.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH 0/3] Enable audio output on AM62-SK
@ 2022-04-21 13:49 ` Nishanth Menon
0 siblings, 0 replies; 15+ messages in thread
From: Nishanth Menon @ 2022-04-21 13:49 UTC (permalink / raw)
To: Jai Luthra
Cc: devicetree, alsa-devel, Vignesh Raghavendra, Jayesh Choudhary,
linux-kernel, Rob Herring, Krzysztof Kozlowski, Peter Ujfalusi,
linux-arm-kernel
On 18:52-20220421, Jai Luthra wrote:
> This patch series adds support for audio output via headphone jack on the
> AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is
> connected to McASP (serializer).
>
> The same 3.5mm jack can be used for combined playback+recording, but audio
> input is currently disabled on McASP until further testing and debugging.
>
> Please apply this series on top of
> https://lore.kernel.org/all/20220415131917.431137-1-vigneshr@ti.com/
>
> Jai Luthra (1):
> arm64: dts: ti: am625-sk: Add audio output support
>
> Jayesh Choudhary (2):
> arm64: dts: ti: k3-am62-main: Add McASP nodes
> ASoC: ti: davinci-mcasp: Add dma-type for bcdma
>
> arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 51 ++++++++++++++
> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
> sound/soc/ti/davinci-mcasp.c | 2 +
> 3 files changed, 142 insertions(+)
>
Please split this series up. Send out the sound/soc/ti/davinci-mcasp.c patch as it's own.
dts changes are their own series.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2022-04-22 13:33 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-04-21 13:22 [PATCH 0/3] Enable audio output on AM62-SK Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` [PATCH 1/3] arm64: dts: ti: k3-am62-main: Add McASP nodes Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` [PATCH 2/3] ASoC: ti: davinci-mcasp: Add dma-type for bcdma Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` [PATCH 3/3] arm64: dts: ti: am625-sk: Add audio output support Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:22 ` Jai Luthra
2022-04-21 13:49 ` [PATCH 0/3] Enable audio output on AM62-SK Nishanth Menon
2022-04-21 13:49 ` Nishanth Menon
2022-04-21 13:49 ` Nishanth Menon
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.