* [PATCH V4 1/4] imx: imx8mp_evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Peng Fan (OSS)
@ 2022-04-15 4:35 ` Peng Fan (OSS)
2022-04-22 8:47 ` sbabic
2022-04-15 4:35 ` [PATCH V4 2/4] imx: imx8mm_evk: " Peng Fan (OSS)
` (3 subsequent siblings)
4 siblings, 1 reply; 10+ messages in thread
From: Peng Fan (OSS) @ 2022-04-15 4:35 UTC (permalink / raw)
To: sbabic, festevam, Peng Fan, NXP i.MX U-Boot Team; +Cc: u-boot
From: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
board/freescale/imx8mp_evk/imx8mp_evk.c | 8 --------
configs/imx8mp_evk_defconfig | 1 +
2 files changed, 1 insertion(+), 8 deletions(-)
diff --git a/board/freescale/imx8mp_evk/imx8mp_evk.c b/board/freescale/imx8mp_evk/imx8mp_evk.c
index 62096c24fb7..fb6c61c39e7 100644
--- a/board/freescale/imx8mp_evk/imx8mp_evk.c
+++ b/board/freescale/imx8mp_evk/imx8mp_evk.c
@@ -20,14 +20,8 @@
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
-static iomux_v3_cfg_t const uart_pads[] = {
- MX8MP_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX8MP_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const wdog_pads[] = {
MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
@@ -40,8 +34,6 @@ int board_early_init_f(void)
set_wdog_reset(wdog);
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-
return 0;
}
diff --git a/configs/imx8mp_evk_defconfig b/configs/imx8mp_evk_defconfig
index c64b699e105..01240e543af 100644
--- a/configs/imx8mp_evk_defconfig
+++ b/configs/imx8mp_evk_defconfig
@@ -91,6 +91,7 @@ CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_POWER_I2C=y
+CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_SYSRESET=y
CONFIG_SPL_SYSRESET=y
--
2.35.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V4 1/4] imx: imx8mp_evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 ` [PATCH V4 1/4] imx: imx8mp_evk: enable CONFIG_DM_SERIAL Peng Fan (OSS)
@ 2022-04-22 8:47 ` sbabic
0 siblings, 0 replies; 10+ messages in thread
From: sbabic @ 2022-04-22 8:47 UTC (permalink / raw)
To: Peng Fan (OSS), u-boot
> From: Peng Fan <peng.fan@nxp.com>
> Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
> marked with u-boot,dm-spl.
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V4 2/4] imx: imx8mm_evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Peng Fan (OSS)
2022-04-15 4:35 ` [PATCH V4 1/4] imx: imx8mp_evk: enable CONFIG_DM_SERIAL Peng Fan (OSS)
@ 2022-04-15 4:35 ` Peng Fan (OSS)
2022-04-22 8:46 ` sbabic
2022-04-15 4:35 ` [PATCH V4 3/4] imx: imx8mn_evk: " Peng Fan (OSS)
` (2 subsequent siblings)
4 siblings, 1 reply; 10+ messages in thread
From: Peng Fan (OSS) @ 2022-04-15 4:35 UTC (permalink / raw)
To: sbabic, festevam, Peng Fan, NXP i.MX U-Boot Team; +Cc: u-boot
From: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
board/freescale/imx8mm_evk/spl.c | 12 ++----------
configs/imx8mm_evk_defconfig | 1 +
2 files changed, 3 insertions(+), 10 deletions(-)
diff --git a/board/freescale/imx8mm_evk/spl.c b/board/freescale/imx8mm_evk/spl.c
index cf4882cd10c..7eeec6c485a 100644
--- a/board/freescale/imx8mm_evk/spl.c
+++ b/board/freescale/imx8mm_evk/spl.c
@@ -72,14 +72,8 @@ int board_fit_config_name_match(const char *name)
}
#endif
-#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
-static iomux_v3_cfg_t const uart_pads[] = {
- IMX8MM_PAD_UART2_RXD_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- IMX8MM_PAD_UART2_TXD_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const wdog_pads[] = {
IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
@@ -92,8 +86,6 @@ int board_early_init_f(void)
set_wdog_reset(wdog);
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-
return 0;
}
@@ -147,8 +139,6 @@ void board_init_f(ulong dummy)
timer_init();
- preloader_console_init();
-
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
@@ -166,6 +156,8 @@ void board_init_f(ulong dummy)
hang();
}
+ preloader_console_init();
+
enable_tzc380();
power_init_board();
diff --git a/configs/imx8mm_evk_defconfig b/configs/imx8mm_evk_defconfig
index 36bf17d1ac0..9ee157c214a 100644
--- a/configs/imx8mm_evk_defconfig
+++ b/configs/imx8mm_evk_defconfig
@@ -79,6 +79,7 @@ CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_DM_PWM=y
+CONFIG_DM_SERIAL=y
CONFIG_PWM_IMX=y
CONFIG_MXC_UART=y
CONFIG_SYSRESET=y
--
2.35.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V4 2/4] imx: imx8mm_evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 ` [PATCH V4 2/4] imx: imx8mm_evk: " Peng Fan (OSS)
@ 2022-04-22 8:46 ` sbabic
0 siblings, 0 replies; 10+ messages in thread
From: sbabic @ 2022-04-22 8:46 UTC (permalink / raw)
To: Peng Fan (OSS), u-boot
> From: Peng Fan <peng.fan@nxp.com>
> Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
> marked with u-boot,dm-spl.
> move the preloader_console_init() call after spl_early_init() to
> avoid board hang
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V4 3/4] imx: imx8mn_evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Peng Fan (OSS)
2022-04-15 4:35 ` [PATCH V4 1/4] imx: imx8mp_evk: enable CONFIG_DM_SERIAL Peng Fan (OSS)
2022-04-15 4:35 ` [PATCH V4 2/4] imx: imx8mm_evk: " Peng Fan (OSS)
@ 2022-04-15 4:35 ` Peng Fan (OSS)
2022-04-22 8:46 ` sbabic
2022-04-15 4:35 ` [PATCH V4 4/4] imx: imx8mq-evk: " Peng Fan (OSS)
2022-04-16 12:10 ` [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Fabio Estevam
4 siblings, 1 reply; 10+ messages in thread
From: Peng Fan (OSS) @ 2022-04-15 4:35 UTC (permalink / raw)
To: sbabic, festevam, NXP i.MX U-Boot Team, Peng Fan; +Cc: u-boot
From: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
board/freescale/imx8mn_evk/spl.c | 12 ++----------
configs/imx8mn_ddr4_evk_defconfig | 1 +
configs/imx8mn_evk_defconfig | 1 -
3 files changed, 3 insertions(+), 11 deletions(-)
diff --git a/board/freescale/imx8mn_evk/spl.c b/board/freescale/imx8mn_evk/spl.c
index dfa81a0d652..63f335be3b0 100644
--- a/board/freescale/imx8mn_evk/spl.c
+++ b/board/freescale/imx8mn_evk/spl.c
@@ -115,14 +115,8 @@ int board_fit_config_name_match(const char *name)
}
#endif
-#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
-static iomux_v3_cfg_t const uart_pads[] = {
- IMX8MN_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- IMX8MN_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
static iomux_v3_cfg_t const wdog_pads[] = {
IMX8MN_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
@@ -135,8 +129,6 @@ int board_early_init_f(void)
set_wdog_reset(wdog);
- imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-
return 0;
}
@@ -152,8 +144,6 @@ void board_init_f(ulong dummy)
timer_init();
- preloader_console_init();
-
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
@@ -163,6 +153,8 @@ void board_init_f(ulong dummy)
hang();
}
+ preloader_console_init();
+
enable_tzc380();
/* DDR initialization */
diff --git a/configs/imx8mn_ddr4_evk_defconfig b/configs/imx8mn_ddr4_evk_defconfig
index 917cdb5aa9d..474d9cfa4d2 100644
--- a/configs/imx8mn_ddr4_evk_defconfig
+++ b/configs/imx8mn_ddr4_evk_defconfig
@@ -76,6 +76,7 @@ CONFIG_PINCTRL_IMX8M=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_SYSRESET=y
CONFIG_SPL_SYSRESET=y
diff --git a/configs/imx8mn_evk_defconfig b/configs/imx8mn_evk_defconfig
index b2981d1e369..5bc175154ba 100644
--- a/configs/imx8mn_evk_defconfig
+++ b/configs/imx8mn_evk_defconfig
@@ -84,7 +84,6 @@ CONFIG_SPL_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_DM_SERIAL=y
-# CONFIG_SPL_DM_SERIAL is not set
CONFIG_MXC_UART=y
CONFIG_SYSRESET=y
CONFIG_SPL_SYSRESET=y
--
2.35.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V4 3/4] imx: imx8mn_evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 ` [PATCH V4 3/4] imx: imx8mn_evk: " Peng Fan (OSS)
@ 2022-04-22 8:46 ` sbabic
0 siblings, 0 replies; 10+ messages in thread
From: sbabic @ 2022-04-22 8:46 UTC (permalink / raw)
To: Peng Fan (OSS), u-boot
> From: Peng Fan <peng.fan@nxp.com>
> Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
> marked with u-boot,dm-spl.
> move the preloader_console_init() call after spl_init() to
> avoid board hang
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V4 4/4] imx: imx8mq-evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Peng Fan (OSS)
` (2 preceding siblings ...)
2022-04-15 4:35 ` [PATCH V4 3/4] imx: imx8mn_evk: " Peng Fan (OSS)
@ 2022-04-15 4:35 ` Peng Fan (OSS)
2022-04-22 8:47 ` sbabic
2022-04-16 12:10 ` [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Fabio Estevam
4 siblings, 1 reply; 10+ messages in thread
From: Peng Fan (OSS) @ 2022-04-15 4:35 UTC (permalink / raw)
To: sbabic, festevam, NXP i.MX U-Boot Team, Peng Fan; +Cc: u-boot
From: Peng Fan <peng.fan@nxp.com>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm/dts/imx8mq-evk-u-boot.dtsi | 32 +++++++++++++++++++++++++++++
configs/imx8mq_evk_defconfig | 1 +
2 files changed, 33 insertions(+)
diff --git a/arch/arm/dts/imx8mq-evk-u-boot.dtsi b/arch/arm/dts/imx8mq-evk-u-boot.dtsi
index 6f9c81462ea..919c1f66d38 100644
--- a/arch/arm/dts/imx8mq-evk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mq-evk-u-boot.dtsi
@@ -2,6 +2,34 @@
#include "imx8mq-u-boot.dtsi"
+&{/soc@0} {
+ u-boot,dm-spl;
+};
+
+&{/soc@0/bus@30000000} {
+ u-boot,dm-spl;
+};
+
+&{/soc@0/bus@30400000} {
+ u-boot,dm-spl;
+};
+
+&{/soc@0/bus@30800000} {
+ u-boot,dm-spl;
+};
+
+&{/soc@0/bus@32c00000} {
+ u-boot,dm-spl;
+};
+
+&iomuxc {
+ u-boot,dm-spl;
+};
+
+&pinctrl_uart1 {
+ u-boot,dm-spl;
+};
+
&usdhc1 {
mmc-hs400-1_8v;
};
@@ -10,3 +38,7 @@
sd-uhs-sdr104;
sd-uhs-ddr50;
};
+
+&uart1 {
+ u-boot,dm-spl;
+};
diff --git a/configs/imx8mq_evk_defconfig b/configs/imx8mq_evk_defconfig
index df7a259f35a..780f93103c7 100644
--- a/configs/imx8mq_evk_defconfig
+++ b/configs/imx8mq_evk_defconfig
@@ -80,6 +80,7 @@ CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_POWER_I2C=y
CONFIG_DM_RESET=y
+CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_DM_THERMAL=y
CONFIG_USB=y
--
2.35.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V4 4/4] imx: imx8mq-evk: enable CONFIG_DM_SERIAL
2022-04-15 4:35 ` [PATCH V4 4/4] imx: imx8mq-evk: " Peng Fan (OSS)
@ 2022-04-22 8:47 ` sbabic
0 siblings, 0 replies; 10+ messages in thread
From: sbabic @ 2022-04-22 8:47 UTC (permalink / raw)
To: Peng Fan (OSS), u-boot
> From: Peng Fan <peng.fan@nxp.com>
> Marked related nodes as u-boot,dm-spl for serial driver model
> Enable CONFIG_DM_SERIAL
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic@denx.de
=====================================================================
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V4 0/4] imx: imx8m: enable DM SERIAL
2022-04-15 4:35 [PATCH V4 0/4] imx: imx8m: enable DM SERIAL Peng Fan (OSS)
` (3 preceding siblings ...)
2022-04-15 4:35 ` [PATCH V4 4/4] imx: imx8mq-evk: " Peng Fan (OSS)
@ 2022-04-16 12:10 ` Fabio Estevam
4 siblings, 0 replies; 10+ messages in thread
From: Fabio Estevam @ 2022-04-16 12:10 UTC (permalink / raw)
To: Peng Fan (OSS); +Cc: Stefano Babic, Peng Fan, U-Boot-Denx
Hi Peng,
On Fri, Apr 15, 2022 at 12:54 AM Peng Fan (OSS) <peng.fan@oss.nxp.com> wrote:
>
> From: Peng Fan <peng.fan@nxp.com>
>
> V4:
> Rebased, update commit log Per Tim's comments
>
> V3:
> Add missed Signed-off-by
> Rebased to only add CONFIG_DM_SERIAL, not touch other config change in defconfig
>
> V2:
> Include imx8mq-evk in this patchset.
> For i.MX8MN/M/P, drop board level uart pinmux settings,
> move preloader_console_init after driver probe.
>
> Tested on all four boards. Note i.MX8MQ-EVK not have SPL_DM, so pinmux for
> uart still there for spl usage.
>
>
> Peng Fan (4):
> imx: imx8mp_evk: enable CONFIG_DM_SERIAL
> imx: imx8mm_evk: enable CONFIG_DM_SERIAL
> imx: imx8mn_evk: enable CONFIG_DM_SERIAL
> imx: imx8mq-evk: enable CONFIG_DM_SERIAL
For the series:
Reviewed-by: Fabio Estevam <festevam@denx.de>
^ permalink raw reply [flat|nested] 10+ messages in thread