[PATCH 0/2] Add generic serial MIDI driver using serial bus API

[PATCH 0/2] Add generic serial MIDI driver using serial bus API

[Daniel Kaehn]

Generic serial MIDI driver adding support for using serial devices
compatible with the serial bus as raw MIDI devices, allowing using
additional serial devices not compatible with the existing
serial-u16550 driver. Supports only setting standard serial baudrates on
the underlying serial device; however, the underlying serial device can
be configured so that a requested 38.4 kBaud is actually the standard MIDI
3.125 kBaud. Supports DeviceTree configuration.

The need for this driver arose from a project using a Raspberry Pi4 which
needed to receive and send raw MIDI with low latency. The pl011 UART
used is not compatible with the existing serial MIDI driver made for
u16550-style devices. Using a userspace program such as ttymidi to feed
input from the TTY device to a virtual ALSA MIDI device was functional,
but not ideal.

I am not sure if a MIDI driver needing the mentioned 'hack' to clock
38.4 kBaud down to the standard MIDI baud is permissible in the mainline
kernel, but am submitting nevertheless in case it is useful. To my knowledge,
it doesn't seem that there would be any way for this driver to manually
configure a serial port to 3.125 kBaud using the serial bus API (please 
correct me f I'm wrong). In my use case, I am actually configuring one port
to run at 115.2 kBaud for faster communication with a custom onboard MIDI controller.

Daniel Kaehn (2):
  dt-bindings: sound: Add generic serial MIDI device
  Add generic serial MIDI driver using serial bus API

 .../devicetree/bindings/sound/serialmidi.yaml |  41 +++
 sound/drivers/Kconfig                         |  17 +
 sound/drivers/Makefile                        |   2 +
 sound/drivers/serial-generic.c                | 344 ++++++++++++++++++
 4 files changed, 404 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/serialmidi.yaml
 create mode 100644 sound/drivers/serial-generic.c

-- 
2.32.0

[PATCH 0/2] Add generic serial MIDI driver using serial bus API

[Daniel Kaehn]

Generic serial MIDI driver adding support for using serial devices
compatible with the serial bus as raw MIDI devices, allowing using
additional serial devices not compatible with the existing
serial-u16550 driver. Supports only setting standard serial baudrates on
the underlying serial device; however, the underlying serial device can
be configured so that a requested 38.4 kBaud is actually the standard MIDI
3.125 kBaud. Supports DeviceTree configuration.

The need for this driver arose from a project using a Raspberry Pi4 which
needed to receive and send raw MIDI with low latency. The pl011 UART
used is not compatible with the existing serial MIDI driver made for
u16550-style devices. Using a userspace program such as ttymidi to feed
input from the TTY device to a virtual ALSA MIDI device was functional,
but not ideal.

I am not sure if a MIDI driver needing the mentioned 'hack' to clock
38.4 kBaud down to the standard MIDI baud is permissible in the mainline
kernel, but am submitting nevertheless in case it is useful. To my knowledge,
it doesn't seem that there would be any way for this driver to manually
configure a serial port to 3.125 kBaud using the serial bus API (please 
correct me f I'm wrong). In my use case, I am actually configuring one port
to run at 115.2 kBaud for faster communication with a custom onboard MIDI controller.

Daniel Kaehn (2):
  dt-bindings: sound: Add generic serial MIDI device
  Add generic serial MIDI driver using serial bus API

 .../devicetree/bindings/sound/serialmidi.yaml |  41 +++
 sound/drivers/Kconfig                         |  17 +
 sound/drivers/Makefile                        |   2 +
 sound/drivers/serial-generic.c                | 344 ++++++++++++++++++
 4 files changed, 404 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/serialmidi.yaml
 create mode 100644 sound/drivers/serial-generic.c

-- 
2.32.0

[PATCH 1/2] dt-bindings: sound: Add generic serial MIDI device

[Daniel Kaehn]

Adds dt-binding for snd-serial-generic serial MIDI driver

Signed-off-by: Daniel Kaehn <kaehndan@gmail.com>
---
 .../devicetree/bindings/sound/serialmidi.yaml | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/serialmidi.yaml

diff --git a/Documentation/devicetree/bindings/sound/serialmidi.yaml b/Documentation/devicetree/bindings/sound/serialmidi.yaml
new file mode 100644
index 000000000000..900c57c1cfca
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/serialmidi.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/serialmidi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Serial MIDI Device
+
+maintainers:
+  - Daniel Kaehn <kaehndan@gmail.com>
+
+description: |
+  Generic MIDI interface using a serial device. Can only be set to use standard speeds
+  corresponding to supported baud rates of the underlying serial device. If standard MIDI
+  speed of 3.125 kBaud is needed, configure the clocks of the underlying serial device
+  so that a requested speed of 3.840 kBaud resuts in the standard MIDI baud rate.
+
+properties:
+  compatible:
+    const: serialmidi
+
+  speed:
+    maxItems: 1
+    description: |
+      Speed to set the serial port to when the MIDI device is opened.
+      If not specified, the underlying serial device is allowed to use its configured default speed.
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    serial {
+        midi {
+            compatible = "serialmidi";
+            speed = <38400>;
+        };
+    };
-- 
2.32.0

[PATCH 1/2] dt-bindings: sound: Add generic serial MIDI device

[Daniel Kaehn]

Adds dt-binding for snd-serial-generic serial MIDI driver

Signed-off-by: Daniel Kaehn <kaehndan@gmail.com>
---
 .../devicetree/bindings/sound/serialmidi.yaml | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/serialmidi.yaml

diff --git a/Documentation/devicetree/bindings/sound/serialmidi.yaml b/Documentation/devicetree/bindings/sound/serialmidi.yaml
new file mode 100644
index 000000000000..900c57c1cfca
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/serialmidi.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/serialmidi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Serial MIDI Device
+
+maintainers:
+  - Daniel Kaehn <kaehndan@gmail.com>
+
+description: |
+  Generic MIDI interface using a serial device. Can only be set to use standard speeds
+  corresponding to supported baud rates of the underlying serial device. If standard MIDI
+  speed of 3.125 kBaud is needed, configure the clocks of the underlying serial device
+  so that a requested speed of 3.840 kBaud resuts in the standard MIDI baud rate.
+
+properties:
+  compatible:
+    const: serialmidi
+
+  speed:
+    maxItems: 1
+    description: |
+      Speed to set the serial port to when the MIDI device is opened.
+      If not specified, the underlying serial device is allowed to use its configured default speed.
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    serial {
+        midi {
+            compatible = "serialmidi";
+            speed = <38400>;
+        };
+    };
-- 
2.32.0

[PATCH 2/2] Add generic serial MIDI driver using serial bus API

[Daniel Kaehn]

Generic serial MIDI driver adding support for using serial devices
compatible with the serial bus as raw MIDI devices, allowing using
additional serial devices not compatible with the existing
serial-u16550 driver. Supports only setting standard serial baudrates on
the underlying serial device; however, the underlying serial device can
be configured so that a requested 38.4 kBaud is actually the standard MIDI
3.125 kBaud. Supports DeviceTree configuration.

Signed-off-by: Daniel Kaehn <kaehndan@gmail.com>
---

One ugly portion in the code I wanted to point out, but didn't find a
'nice' way of solving. `snd_serial_generic_output_write` is called to
read from ALSA's output MIDI buffer and write to the serdev_device's
input buffer. While copying directly from the former to the later would
be desirable for performance, I assume violating the abstraction would
never be permissable. The current implementation creates an internal buffer of
an arbitrary size (currently 256) and copies there as an intermediate
step. Any advice on how to make this better is appreciated.

 sound/drivers/Kconfig          |  17 ++
 sound/drivers/Makefile         |   2 +
 sound/drivers/serial-generic.c | 344 +++++++++++++++++++++++++++++++++
 3 files changed, 363 insertions(+)
 create mode 100644 sound/drivers/serial-generic.c

diff --git a/sound/drivers/Kconfig b/sound/drivers/Kconfig
index ca4cdf666f82..be9a161cb593 100644
--- a/sound/drivers/Kconfig
+++ b/sound/drivers/Kconfig
@@ -165,6 +165,23 @@ config SND_SERIAL_U16550
 	  To compile this driver as a module, choose M here: the module
 	  will be called snd-serial-u16550.
 
+config SND_SERIAL_GENERIC
+	tristate "Generic serial MIDI driver"
+	depends on SERIAL_DEV_BUS
+	select SND_RAWMIDI
+	help
+	  To include support for mapping generic serial devices as raw
+	  ALSA MIDI devices, say Y here. The driver only supports setting
+	  the serial port to standard baudrates. To attain the standard MIDI
+	  baudrate of 3.125 kBaud, configure the clock of the underlying serial
+	  device so that a requested 3.84 kBaud will result in the standard speed.
+
+	  Use this devicetree binding to configure serial port mapping
+	  <file:Documentation/devicetree/bindings/sound/serialmidi.yaml>
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called snd-serial-generic.
+
 config SND_MPU401
 	tristate "Generic MPU-401 UART driver"
 	select SND_MPU401_UART
diff --git a/sound/drivers/Makefile b/sound/drivers/Makefile
index c0fe4eccdaef..b60303180a1b 100644
--- a/sound/drivers/Makefile
+++ b/sound/drivers/Makefile
@@ -10,6 +10,7 @@ snd-mtpav-objs := mtpav.o
 snd-mts64-objs := mts64.o
 snd-portman2x4-objs := portman2x4.o
 snd-serial-u16550-objs := serial-u16550.o
+snd-serial-generic-objs := serial-generic.o
 snd-virmidi-objs := virmidi.o
 
 # Toplevel Module Dependency
@@ -17,6 +18,7 @@ obj-$(CONFIG_SND_DUMMY) += snd-dummy.o
 obj-$(CONFIG_SND_ALOOP) += snd-aloop.o
 obj-$(CONFIG_SND_VIRMIDI) += snd-virmidi.o
 obj-$(CONFIG_SND_SERIAL_U16550) += snd-serial-u16550.o
+obj-$(CONFIG_SND_SERIAL_GENERIC) += snd-serial-generic.o
 obj-$(CONFIG_SND_MTPAV) += snd-mtpav.o
 obj-$(CONFIG_SND_MTS64) += snd-mts64.o
 obj-$(CONFIG_SND_PORTMAN2X4) += snd-portman2x4.o
diff --git a/sound/drivers/serial-generic.c b/sound/drivers/serial-generic.c
new file mode 100644
index 000000000000..64ca5c898018
--- /dev/null
+++ b/sound/drivers/serial-generic.c
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *   serial-generic.c
+ *   Copyright (c) by Daniel Kaehn <kaehndan@gmail.com
+ *   Based on serial-u16550.c by Jaroslav Kysela <perex@perex.cz>,
+ *		                 Isaku Yamahata <yamahata@private.email.ne.jp>,
+ *		                 George Hansper <ghansper@apana.org.au>,
+ *		                 Hannu Savolainen
+ *
+ * Generic serial MIDI driver using the serdev serial bus API for hardware interaction
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/serdev.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+
+#include <sound/core.h>
+#include <sound/rawmidi.h>
+#include <sound/initval.h>
+
+MODULE_DESCRIPTION("MIDI serial");
+MODULE_LICENSE("GPL");
+
+#define SERIAL_MODE_NOT_OPENED		(0)
+#define SERIAL_MODE_INPUT_OPEN		(1 << 0)
+#define SERIAL_MODE_OUTPUT_OPEN		(1 << 1)
+#define SERIAL_MODE_INPUT_TRIGGERED	(1 << 2)
+#define SERIAL_MODE_OUTPUT_TRIGGERED	(1 << 3)
+
+struct snd_serial_generic {
+	struct serdev_device *serdev;
+
+	struct snd_card *card;
+	struct snd_rawmidi *rmidi;
+	struct snd_rawmidi_substream *midi_output;
+	struct snd_rawmidi_substream *midi_input;
+
+	int filemode;		/* open status of file */
+	unsigned int baudrate;
+};
+
+
+static int snd_serial_generic_ensure_serdev_open(struct snd_serial_generic *drvdata)
+{
+	int err = 0;
+	unsigned int actual_baud;
+
+	if (drvdata->filemode == SERIAL_MODE_NOT_OPENED) {
+		err = serdev_device_open(drvdata->serdev);
+		if (err < 0)
+			return err;
+		if (drvdata->baudrate) {
+			actual_baud = serdev_device_set_baudrate(drvdata->serdev,
+				drvdata->baudrate);
+			if (actual_baud != drvdata->baudrate) {
+				snd_printk(KERN_WARNING "snd-serial-generic: requested %d baud for %s but it was actually set to %d\n",
+					drvdata->baudrate, drvdata->card->shortname, actual_baud);
+			}
+		}
+	}
+	return 0;
+}
+
+static int snd_serial_generic_input_open(struct snd_rawmidi_substream *substream)
+{
+	int err = 0;
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	snd_printd("snd-serial-generic: DEBUG - Opening input for card %s\n",
+		drvdata->card->shortname);
+
+	err = snd_serial_generic_ensure_serdev_open(drvdata);
+	if (err < 0) {
+		snd_printk(KERN_WARNING "snd-serial-generic: failed to open input for card %s",
+			drvdata->card->shortname);
+		return err;
+	}
+
+	drvdata->filemode |= SERIAL_MODE_INPUT_OPEN;
+	drvdata->midi_input = substream;
+	return 0;
+}
+
+static int snd_serial_generic_input_close(struct snd_rawmidi_substream *substream)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	drvdata->filemode &= ~SERIAL_MODE_INPUT_OPEN;
+	drvdata->midi_input = NULL;
+	if (drvdata->filemode == SERIAL_MODE_NOT_OPENED)
+		serdev_device_close(drvdata->serdev);
+	return 0;
+}
+
+static void snd_serial_generic_input_trigger(struct snd_rawmidi_substream *substream,
+					int up)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	if (up)
+		drvdata->filemode |= SERIAL_MODE_INPUT_TRIGGERED;
+	else
+		drvdata->filemode &= ~SERIAL_MODE_INPUT_TRIGGERED;
+}
+
+static int snd_serial_generic_output_open(struct snd_rawmidi_substream *substream)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+	int err;
+
+	snd_printd("snd-serial-generic: DEBUG - Opening output for card %s\n",
+		drvdata->card->shortname);
+
+	err = snd_serial_generic_ensure_serdev_open(drvdata);
+	if (err < 0) {
+		snd_printk(KERN_WARNING "snd-serial-generic: failed to open input for card %s",
+			drvdata->card->shortname);
+		return err;
+	}
+
+	drvdata->filemode |= SERIAL_MODE_OUTPUT_OPEN;
+	drvdata->midi_output = substream;
+	return 0;
+};
+
+static int snd_serial_generic_output_close(struct snd_rawmidi_substream *substream)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	drvdata->filemode &= ~SERIAL_MODE_OUTPUT_OPEN;
+	drvdata->midi_output = NULL;
+	if (drvdata->filemode == SERIAL_MODE_NOT_OPENED)
+		serdev_device_close(drvdata->serdev);
+	return 0;
+};
+
+#define INTERNAL_BUF_SIZE 256
+
+static void snd_serial_generic_output_write(struct snd_rawmidi_substream *substream)
+{
+	static char buf[INTERNAL_BUF_SIZE];
+	int num_bytes;
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	num_bytes = snd_rawmidi_transmit_peek(substream, buf, INTERNAL_BUF_SIZE);
+	num_bytes = serdev_device_write_buf(drvdata->serdev, buf, num_bytes);
+	snd_rawmidi_transmit_ack(substream, num_bytes);
+}
+
+static void snd_serial_generic_output_trigger(struct snd_rawmidi_substream *substream,
+					 int up)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	if (up)
+		drvdata->filemode |= SERIAL_MODE_OUTPUT_TRIGGERED;
+	else
+		drvdata->filemode &= ~SERIAL_MODE_OUTPUT_TRIGGERED;
+	if (up)
+		snd_serial_generic_output_write(substream);
+}
+
+static const struct snd_rawmidi_ops snd_serial_generic_output = {
+	.open =		snd_serial_generic_output_open,
+	.close =	snd_serial_generic_output_close,
+	.trigger =	snd_serial_generic_output_trigger,
+};
+
+static const struct snd_rawmidi_ops snd_serial_generic_input = {
+	.open =		snd_serial_generic_input_open,
+	.close =	snd_serial_generic_input_close,
+	.trigger =	snd_serial_generic_input_trigger,
+};
+
+static int snd_serial_generic_receive_buf(struct serdev_device *serdev,
+				const unsigned char *buf, size_t count)
+{
+	int ret = 0;
+	struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
+
+	ret = snd_rawmidi_receive(drvdata->midi_input, buf, count);
+	return ret < 0 ? 0 : ret;
+}
+
+void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
+{
+	struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
+
+	if (!snd_rawmidi_transmit_empty(drvdata->midi_output))
+		snd_serial_generic_output_write(drvdata->midi_output);
+}
+
+
+static const struct serdev_device_ops snd_serial_generic_serdev_device_ops = {
+	.receive_buf = snd_serial_generic_receive_buf,
+	.write_wakeup = snd_serial_generic_write_wakeup
+};
+
+static int snd_serial_generic_create(struct serdev_device *serdev,
+				struct snd_card *card,
+				struct snd_serial_generic **rserialmidi)
+{
+	struct snd_serial_generic *drvdata;
+	int err;
+
+	drvdata = devm_kzalloc(card->dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata)
+		return -ENOMEM;
+
+	drvdata->serdev = serdev;
+	drvdata->card = card;
+
+	if (serdev->dev.of_node) {
+		err = of_property_read_u32(serdev->dev.of_node, "speed", &drvdata->baudrate);
+		if (err < 0) {
+			snd_printk(KERN_WARNING "snd-serial-generic: MIDI device reading of speed DT param failed with error %d, using default baudrate of serial device\n",
+						err);
+			drvdata->baudrate = 0;
+		}
+	} else {
+		snd_printk(KERN_INFO "snd-serial-generic: MIDI device speed DT param not set for %s, using default baudrate of serial device\n",
+			drvdata->card->shortname);
+		drvdata->baudrate = 0;
+	}
+
+	if (rserialmidi)
+		*rserialmidi = drvdata;
+	return 0;
+}
+
+static void snd_serial_generic_substreams(struct snd_rawmidi_str *stream, int dev_num)
+{
+	struct snd_rawmidi_substream *substream;
+
+	list_for_each_entry(substream, &stream->substreams, list) {
+		sprintf(substream->name, "Serial MIDI %d-%d", dev_num, substream->number);
+	}
+}
+
+static int snd_serial_generic_rmidi(struct snd_serial_generic *drvdata,
+				int outs, int ins, struct snd_rawmidi **rmidi)
+{
+	struct snd_rawmidi *rrawmidi;
+	int err;
+
+	err = snd_rawmidi_new(drvdata->card, drvdata->card->driver, 0, outs, ins, &rrawmidi);
+	if (err < 0)
+		return err;
+
+	snd_rawmidi_set_ops(rrawmidi, SNDRV_RAWMIDI_STREAM_INPUT,
+				&snd_serial_generic_input);
+	snd_rawmidi_set_ops(rrawmidi, SNDRV_RAWMIDI_STREAM_OUTPUT,
+				&snd_serial_generic_output);
+	strcpy(rrawmidi->name, drvdata->card->shortname);
+
+	snd_serial_generic_substreams(&rrawmidi->streams[SNDRV_RAWMIDI_STREAM_OUTPUT],
+					drvdata->serdev->ctrl->nr);
+	snd_serial_generic_substreams(&rrawmidi->streams[SNDRV_RAWMIDI_STREAM_INPUT],
+					drvdata->serdev->ctrl->nr);
+
+	rrawmidi->info_flags = SNDRV_RAWMIDI_INFO_OUTPUT |
+			       SNDRV_RAWMIDI_INFO_INPUT |
+			       SNDRV_RAWMIDI_INFO_DUPLEX;
+
+	rrawmidi->private_data = drvdata;
+	if (rmidi)
+		*rmidi = rrawmidi;
+	return 0;
+}
+
+static int snd_serial_generic_probe(struct serdev_device *serdev)
+{
+	struct snd_card *card;
+	struct snd_serial_generic *drvdata;
+	int err;
+
+	pr_debug("snd-serial-generic: probe called with:\n\tcontroller number: %d\n",
+		serdev->ctrl->nr);
+
+	err  = snd_devm_card_new(&serdev->dev, SNDRV_DEFAULT_IDX1,
+				SNDRV_DEFAULT_STR1, THIS_MODULE, 0, &card);
+	if (err < 0)
+		return err;
+
+	strcpy(card->driver, "SerialMIDI");
+	sprintf(card->shortname, "SerialMIDI-%d", serdev->ctrl->nr);
+	sprintf(card->longname, "Serial MIDI device at serial%d", serdev->ctrl->nr);
+
+	err = snd_serial_generic_create(serdev, card, &drvdata);
+	if (err < 0)
+		return err;
+
+	err = snd_serial_generic_rmidi(drvdata, 1, 1, &drvdata->rmidi);
+	if (err < 0)
+		return err;
+
+	serdev_device_set_client_ops(serdev, &snd_serial_generic_serdev_device_ops);
+	serdev_device_set_drvdata(drvdata->serdev, drvdata);
+
+	err = snd_card_register(card);
+
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+
+#define SND_SERIAL_GENERIC_DRIVER	"snd-serial-generic"
+
+static const struct of_device_id snd_serial_generic_dt_ids[] = {
+	{ .compatible = "serialmidi" },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, snd_serial_generic_dt_ids);
+
+static struct serdev_device_driver snd_serial_generic_driver = {
+	.driver	= {
+		.name		= SND_SERIAL_GENERIC_DRIVER,
+		.of_match_table	= of_match_ptr(snd_serial_generic_dt_ids),
+	},
+	.probe	= snd_serial_generic_probe,
+};
+
+static int __init alsa_card_serial_generic_init(void)
+{
+	snd_printk(KERN_INFO "snd-serial-generic: Generic serial-based MIDI device\n");
+	return serdev_device_driver_register(&snd_serial_generic_driver);
+}
+
+static void __exit alsa_card_serial_generic_exit(void)
+{
+	serdev_device_driver_unregister(&snd_serial_generic_driver);
+}
+
+module_init(alsa_card_serial_generic_init)
+module_exit(alsa_card_serial_generic_exit)
-- 
2.32.0

[PATCH 2/2] Add generic serial MIDI driver using serial bus API

[Daniel Kaehn]

Generic serial MIDI driver adding support for using serial devices
compatible with the serial bus as raw MIDI devices, allowing using
additional serial devices not compatible with the existing
serial-u16550 driver. Supports only setting standard serial baudrates on
the underlying serial device; however, the underlying serial device can
be configured so that a requested 38.4 kBaud is actually the standard MIDI
3.125 kBaud. Supports DeviceTree configuration.

Signed-off-by: Daniel Kaehn <kaehndan@gmail.com>
---

One ugly portion in the code I wanted to point out, but didn't find a
'nice' way of solving. `snd_serial_generic_output_write` is called to
read from ALSA's output MIDI buffer and write to the serdev_device's
input buffer. While copying directly from the former to the later would
be desirable for performance, I assume violating the abstraction would
never be permissable. The current implementation creates an internal buffer of
an arbitrary size (currently 256) and copies there as an intermediate
step. Any advice on how to make this better is appreciated.

 sound/drivers/Kconfig          |  17 ++
 sound/drivers/Makefile         |   2 +
 sound/drivers/serial-generic.c | 344 +++++++++++++++++++++++++++++++++
 3 files changed, 363 insertions(+)
 create mode 100644 sound/drivers/serial-generic.c

diff --git a/sound/drivers/Kconfig b/sound/drivers/Kconfig
index ca4cdf666f82..be9a161cb593 100644
--- a/sound/drivers/Kconfig
+++ b/sound/drivers/Kconfig
@@ -165,6 +165,23 @@ config SND_SERIAL_U16550
 	  To compile this driver as a module, choose M here: the module
 	  will be called snd-serial-u16550.
 
+config SND_SERIAL_GENERIC
+	tristate "Generic serial MIDI driver"
+	depends on SERIAL_DEV_BUS
+	select SND_RAWMIDI
+	help
+	  To include support for mapping generic serial devices as raw
+	  ALSA MIDI devices, say Y here. The driver only supports setting
+	  the serial port to standard baudrates. To attain the standard MIDI
+	  baudrate of 3.125 kBaud, configure the clock of the underlying serial
+	  device so that a requested 3.84 kBaud will result in the standard speed.
+
+	  Use this devicetree binding to configure serial port mapping
+	  <file:Documentation/devicetree/bindings/sound/serialmidi.yaml>
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called snd-serial-generic.
+
 config SND_MPU401
 	tristate "Generic MPU-401 UART driver"
 	select SND_MPU401_UART
diff --git a/sound/drivers/Makefile b/sound/drivers/Makefile
index c0fe4eccdaef..b60303180a1b 100644
--- a/sound/drivers/Makefile
+++ b/sound/drivers/Makefile
@@ -10,6 +10,7 @@ snd-mtpav-objs := mtpav.o
 snd-mts64-objs := mts64.o
 snd-portman2x4-objs := portman2x4.o
 snd-serial-u16550-objs := serial-u16550.o
+snd-serial-generic-objs := serial-generic.o
 snd-virmidi-objs := virmidi.o
 
 # Toplevel Module Dependency
@@ -17,6 +18,7 @@ obj-$(CONFIG_SND_DUMMY) += snd-dummy.o
 obj-$(CONFIG_SND_ALOOP) += snd-aloop.o
 obj-$(CONFIG_SND_VIRMIDI) += snd-virmidi.o
 obj-$(CONFIG_SND_SERIAL_U16550) += snd-serial-u16550.o
+obj-$(CONFIG_SND_SERIAL_GENERIC) += snd-serial-generic.o
 obj-$(CONFIG_SND_MTPAV) += snd-mtpav.o
 obj-$(CONFIG_SND_MTS64) += snd-mts64.o
 obj-$(CONFIG_SND_PORTMAN2X4) += snd-portman2x4.o
diff --git a/sound/drivers/serial-generic.c b/sound/drivers/serial-generic.c
new file mode 100644
index 000000000000..64ca5c898018
--- /dev/null
+++ b/sound/drivers/serial-generic.c
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *   serial-generic.c
+ *   Copyright (c) by Daniel Kaehn <kaehndan@gmail.com
+ *   Based on serial-u16550.c by Jaroslav Kysela <perex@perex.cz>,
+ *		                 Isaku Yamahata <yamahata@private.email.ne.jp>,
+ *		                 George Hansper <ghansper@apana.org.au>,
+ *		                 Hannu Savolainen
+ *
+ * Generic serial MIDI driver using the serdev serial bus API for hardware interaction
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/serdev.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+
+#include <sound/core.h>
+#include <sound/rawmidi.h>
+#include <sound/initval.h>
+
+MODULE_DESCRIPTION("MIDI serial");
+MODULE_LICENSE("GPL");
+
+#define SERIAL_MODE_NOT_OPENED		(0)
+#define SERIAL_MODE_INPUT_OPEN		(1 << 0)
+#define SERIAL_MODE_OUTPUT_OPEN		(1 << 1)
+#define SERIAL_MODE_INPUT_TRIGGERED	(1 << 2)
+#define SERIAL_MODE_OUTPUT_TRIGGERED	(1 << 3)
+
+struct snd_serial_generic {
+	struct serdev_device *serdev;
+
+	struct snd_card *card;
+	struct snd_rawmidi *rmidi;
+	struct snd_rawmidi_substream *midi_output;
+	struct snd_rawmidi_substream *midi_input;
+
+	int filemode;		/* open status of file */
+	unsigned int baudrate;
+};
+
+
+static int snd_serial_generic_ensure_serdev_open(struct snd_serial_generic *drvdata)
+{
+	int err = 0;
+	unsigned int actual_baud;
+
+	if (drvdata->filemode == SERIAL_MODE_NOT_OPENED) {
+		err = serdev_device_open(drvdata->serdev);
+		if (err < 0)
+			return err;
+		if (drvdata->baudrate) {
+			actual_baud = serdev_device_set_baudrate(drvdata->serdev,
+				drvdata->baudrate);
+			if (actual_baud != drvdata->baudrate) {
+				snd_printk(KERN_WARNING "snd-serial-generic: requested %d baud for %s but it was actually set to %d\n",
+					drvdata->baudrate, drvdata->card->shortname, actual_baud);
+			}
+		}
+	}
+	return 0;
+}
+
+static int snd_serial_generic_input_open(struct snd_rawmidi_substream *substream)
+{
+	int err = 0;
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	snd_printd("snd-serial-generic: DEBUG - Opening input for card %s\n",
+		drvdata->card->shortname);
+
+	err = snd_serial_generic_ensure_serdev_open(drvdata);
+	if (err < 0) {
+		snd_printk(KERN_WARNING "snd-serial-generic: failed to open input for card %s",
+			drvdata->card->shortname);
+		return err;
+	}
+
+	drvdata->filemode |= SERIAL_MODE_INPUT_OPEN;
+	drvdata->midi_input = substream;
+	return 0;
+}
+
+static int snd_serial_generic_input_close(struct snd_rawmidi_substream *substream)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	drvdata->filemode &= ~SERIAL_MODE_INPUT_OPEN;
+	drvdata->midi_input = NULL;
+	if (drvdata->filemode == SERIAL_MODE_NOT_OPENED)
+		serdev_device_close(drvdata->serdev);
+	return 0;
+}
+
+static void snd_serial_generic_input_trigger(struct snd_rawmidi_substream *substream,
+					int up)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	if (up)
+		drvdata->filemode |= SERIAL_MODE_INPUT_TRIGGERED;
+	else
+		drvdata->filemode &= ~SERIAL_MODE_INPUT_TRIGGERED;
+}
+
+static int snd_serial_generic_output_open(struct snd_rawmidi_substream *substream)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+	int err;
+
+	snd_printd("snd-serial-generic: DEBUG - Opening output for card %s\n",
+		drvdata->card->shortname);
+
+	err = snd_serial_generic_ensure_serdev_open(drvdata);
+	if (err < 0) {
+		snd_printk(KERN_WARNING "snd-serial-generic: failed to open input for card %s",
+			drvdata->card->shortname);
+		return err;
+	}
+
+	drvdata->filemode |= SERIAL_MODE_OUTPUT_OPEN;
+	drvdata->midi_output = substream;
+	return 0;
+};
+
+static int snd_serial_generic_output_close(struct snd_rawmidi_substream *substream)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	drvdata->filemode &= ~SERIAL_MODE_OUTPUT_OPEN;
+	drvdata->midi_output = NULL;
+	if (drvdata->filemode == SERIAL_MODE_NOT_OPENED)
+		serdev_device_close(drvdata->serdev);
+	return 0;
+};
+
+#define INTERNAL_BUF_SIZE 256
+
+static void snd_serial_generic_output_write(struct snd_rawmidi_substream *substream)
+{
+	static char buf[INTERNAL_BUF_SIZE];
+	int num_bytes;
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	num_bytes = snd_rawmidi_transmit_peek(substream, buf, INTERNAL_BUF_SIZE);
+	num_bytes = serdev_device_write_buf(drvdata->serdev, buf, num_bytes);
+	snd_rawmidi_transmit_ack(substream, num_bytes);
+}
+
+static void snd_serial_generic_output_trigger(struct snd_rawmidi_substream *substream,
+					 int up)
+{
+	struct snd_serial_generic *drvdata = substream->rmidi->private_data;
+
+	if (up)
+		drvdata->filemode |= SERIAL_MODE_OUTPUT_TRIGGERED;
+	else
+		drvdata->filemode &= ~SERIAL_MODE_OUTPUT_TRIGGERED;
+	if (up)
+		snd_serial_generic_output_write(substream);
+}
+
+static const struct snd_rawmidi_ops snd_serial_generic_output = {
+	.open =		snd_serial_generic_output_open,
+	.close =	snd_serial_generic_output_close,
+	.trigger =	snd_serial_generic_output_trigger,
+};
+
+static const struct snd_rawmidi_ops snd_serial_generic_input = {
+	.open =		snd_serial_generic_input_open,
+	.close =	snd_serial_generic_input_close,
+	.trigger =	snd_serial_generic_input_trigger,
+};
+
+static int snd_serial_generic_receive_buf(struct serdev_device *serdev,
+				const unsigned char *buf, size_t count)
+{
+	int ret = 0;
+	struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
+
+	ret = snd_rawmidi_receive(drvdata->midi_input, buf, count);
+	return ret < 0 ? 0 : ret;
+}
+
+void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
+{
+	struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
+
+	if (!snd_rawmidi_transmit_empty(drvdata->midi_output))
+		snd_serial_generic_output_write(drvdata->midi_output);
+}
+
+
+static const struct serdev_device_ops snd_serial_generic_serdev_device_ops = {
+	.receive_buf = snd_serial_generic_receive_buf,
+	.write_wakeup = snd_serial_generic_write_wakeup
+};
+
+static int snd_serial_generic_create(struct serdev_device *serdev,
+				struct snd_card *card,
+				struct snd_serial_generic **rserialmidi)
+{
+	struct snd_serial_generic *drvdata;
+	int err;
+
+	drvdata = devm_kzalloc(card->dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata)
+		return -ENOMEM;
+
+	drvdata->serdev = serdev;
+	drvdata->card = card;
+
+	if (serdev->dev.of_node) {
+		err = of_property_read_u32(serdev->dev.of_node, "speed", &drvdata->baudrate);
+		if (err < 0) {
+			snd_printk(KERN_WARNING "snd-serial-generic: MIDI device reading of speed DT param failed with error %d, using default baudrate of serial device\n",
+						err);
+			drvdata->baudrate = 0;
+		}
+	} else {
+		snd_printk(KERN_INFO "snd-serial-generic: MIDI device speed DT param not set for %s, using default baudrate of serial device\n",
+			drvdata->card->shortname);
+		drvdata->baudrate = 0;
+	}
+
+	if (rserialmidi)
+		*rserialmidi = drvdata;
+	return 0;
+}
+
+static void snd_serial_generic_substreams(struct snd_rawmidi_str *stream, int dev_num)
+{
+	struct snd_rawmidi_substream *substream;
+
+	list_for_each_entry(substream, &stream->substreams, list) {
+		sprintf(substream->name, "Serial MIDI %d-%d", dev_num, substream->number);
+	}
+}
+
+static int snd_serial_generic_rmidi(struct snd_serial_generic *drvdata,
+				int outs, int ins, struct snd_rawmidi **rmidi)
+{
+	struct snd_rawmidi *rrawmidi;
+	int err;
+
+	err = snd_rawmidi_new(drvdata->card, drvdata->card->driver, 0, outs, ins, &rrawmidi);
+	if (err < 0)
+		return err;
+
+	snd_rawmidi_set_ops(rrawmidi, SNDRV_RAWMIDI_STREAM_INPUT,
+				&snd_serial_generic_input);
+	snd_rawmidi_set_ops(rrawmidi, SNDRV_RAWMIDI_STREAM_OUTPUT,
+				&snd_serial_generic_output);
+	strcpy(rrawmidi->name, drvdata->card->shortname);
+
+	snd_serial_generic_substreams(&rrawmidi->streams[SNDRV_RAWMIDI_STREAM_OUTPUT],
+					drvdata->serdev->ctrl->nr);
+	snd_serial_generic_substreams(&rrawmidi->streams[SNDRV_RAWMIDI_STREAM_INPUT],
+					drvdata->serdev->ctrl->nr);
+
+	rrawmidi->info_flags = SNDRV_RAWMIDI_INFO_OUTPUT |
+			       SNDRV_RAWMIDI_INFO_INPUT |
+			       SNDRV_RAWMIDI_INFO_DUPLEX;
+
+	rrawmidi->private_data = drvdata;
+	if (rmidi)
+		*rmidi = rrawmidi;
+	return 0;
+}
+
+static int snd_serial_generic_probe(struct serdev_device *serdev)
+{
+	struct snd_card *card;
+	struct snd_serial_generic *drvdata;
+	int err;
+
+	pr_debug("snd-serial-generic: probe called with:\n\tcontroller number: %d\n",
+		serdev->ctrl->nr);
+
+	err  = snd_devm_card_new(&serdev->dev, SNDRV_DEFAULT_IDX1,
+				SNDRV_DEFAULT_STR1, THIS_MODULE, 0, &card);
+	if (err < 0)
+		return err;
+
+	strcpy(card->driver, "SerialMIDI");
+	sprintf(card->shortname, "SerialMIDI-%d", serdev->ctrl->nr);
+	sprintf(card->longname, "Serial MIDI device at serial%d", serdev->ctrl->nr);
+
+	err = snd_serial_generic_create(serdev, card, &drvdata);
+	if (err < 0)
+		return err;
+
+	err = snd_serial_generic_rmidi(drvdata, 1, 1, &drvdata->rmidi);
+	if (err < 0)
+		return err;
+
+	serdev_device_set_client_ops(serdev, &snd_serial_generic_serdev_device_ops);
+	serdev_device_set_drvdata(drvdata->serdev, drvdata);
+
+	err = snd_card_register(card);
+
+	if (err < 0)
+		return err;
+
+	return 0;
+}
+
+#define SND_SERIAL_GENERIC_DRIVER	"snd-serial-generic"
+
+static const struct of_device_id snd_serial_generic_dt_ids[] = {
+	{ .compatible = "serialmidi" },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, snd_serial_generic_dt_ids);
+
+static struct serdev_device_driver snd_serial_generic_driver = {
+	.driver	= {
+		.name		= SND_SERIAL_GENERIC_DRIVER,
+		.of_match_table	= of_match_ptr(snd_serial_generic_dt_ids),
+	},
+	.probe	= snd_serial_generic_probe,
+};
+
+static int __init alsa_card_serial_generic_init(void)
+{
+	snd_printk(KERN_INFO "snd-serial-generic: Generic serial-based MIDI device\n");
+	return serdev_device_driver_register(&snd_serial_generic_driver);
+}
+
+static void __exit alsa_card_serial_generic_exit(void)
+{
+	serdev_device_driver_unregister(&snd_serial_generic_driver);
+}
+
+module_init(alsa_card_serial_generic_init)
+module_exit(alsa_card_serial_generic_exit)
-- 
2.32.0

Re: [PATCH 2/2] Add generic serial MIDI driver using serial bus API

[kernel test robot]

Hi Daniel,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on tiwai-sound/for-next]
[also build test WARNING on v5.18-rc3 next-20220420]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/intel-lab-lkp/linux/commits/Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
base:   https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git for-next
config: ia64-allyesconfig (https://download.01.org/0day-ci/archive/20220421/202204211211.RPFL9E3X-lkp@intel.com/config)
compiler: ia64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/intel-lab-lkp/linux/commit/65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
        git checkout 65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross W=1 O=build_dir ARCH=ia64 SHELL=/bin/bash sound/drivers/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> sound/drivers/serial-generic.c:192:6: warning: no previous prototype for 'snd_serial_generic_write_wakeup' [-Wmissing-prototypes]
     192 | void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
         |      ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


vim +/snd_serial_generic_write_wakeup +192 sound/drivers/serial-generic.c

   191	
 > 192	void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
   193	{
   194		struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
   195	
   196		if (!snd_rawmidi_transmit_empty(drvdata->midi_output))
   197			snd_serial_generic_output_write(drvdata->midi_output);
   198	}
   199	

-- 
0-DAY CI Kernel Test Service
https://01.org/lkp

Re: [PATCH 2/2] Add generic serial MIDI driver using serial bus API

[kernel test robot]

Hi Daniel,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on tiwai-sound/for-next]
[also build test WARNING on v5.18-rc3 next-20220420]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/intel-lab-lkp/linux/commits/Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
base:   https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git for-next
config: ia64-allyesconfig (https://download.01.org/0day-ci/archive/20220421/202204211211.RPFL9E3X-lkp@intel.com/config)
compiler: ia64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/intel-lab-lkp/linux/commit/65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
        git checkout 65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross W=1 O=build_dir ARCH=ia64 SHELL=/bin/bash sound/drivers/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> sound/drivers/serial-generic.c:192:6: warning: no previous prototype for 'snd_serial_generic_write_wakeup' [-Wmissing-prototypes]
     192 | void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
         |      ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


vim +/snd_serial_generic_write_wakeup +192 sound/drivers/serial-generic.c

   191	
 > 192	void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
   193	{
   194		struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
   195	
   196		if (!snd_rawmidi_transmit_empty(drvdata->midi_output))
   197			snd_serial_generic_output_write(drvdata->midi_output);
   198	}
   199	

-- 
0-DAY CI Kernel Test Service
https://01.org/lkp

Re: [PATCH 2/2] Add generic serial MIDI driver using serial bus API

[kernel test robot]

Hi Daniel,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on tiwai-sound/for-next]
[also build test WARNING on v5.18-rc4 next-20220422]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/intel-lab-lkp/linux/commits/Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
base:   https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git for-next
config: arm64-allyesconfig (https://download.01.org/0day-ci/archive/20220426/202204260120.TIXTqkq1-lkp@intel.com/config)
compiler: clang version 15.0.0 (https://github.com/llvm/llvm-project 1cddcfdc3c683b393df1a5c9063252eb60e52818)
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # install arm64 cross compiling tool for clang build
        # apt-get install binutils-aarch64-linux-gnu
        # https://github.com/intel-lab-lkp/linux/commit/65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
        git checkout 65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash arch/arm64/kernel/ drivers/acpi/arm64/ sound/drivers/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> sound/drivers/serial-generic.c:192:6: warning: no previous prototype for function 'snd_serial_generic_write_wakeup' [-Wmissing-prototypes]
   void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
        ^
   sound/drivers/serial-generic.c:192:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
   void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
   ^
   static 
   1 warning generated.


vim +/snd_serial_generic_write_wakeup +192 sound/drivers/serial-generic.c

   191	
 > 192	void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
   193	{
   194		struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
   195	
   196		if (!snd_rawmidi_transmit_empty(drvdata->midi_output))
   197			snd_serial_generic_output_write(drvdata->midi_output);
   198	}
   199	

-- 
0-DAY CI Kernel Test Service
https://01.org/lkp

Re: [PATCH 2/2] Add generic serial MIDI driver using serial bus API

[kernel test robot]

Hi Daniel,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on tiwai-sound/for-next]
[also build test WARNING on v5.18-rc4 next-20220422]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/intel-lab-lkp/linux/commits/Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
base:   https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git for-next
config: arm64-allyesconfig (https://download.01.org/0day-ci/archive/20220426/202204260120.TIXTqkq1-lkp@intel.com/config)
compiler: clang version 15.0.0 (https://github.com/llvm/llvm-project 1cddcfdc3c683b393df1a5c9063252eb60e52818)
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # install arm64 cross compiling tool for clang build
        # apt-get install binutils-aarch64-linux-gnu
        # https://github.com/intel-lab-lkp/linux/commit/65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review Daniel-Kaehn/Add-generic-serial-MIDI-driver-using-serial-bus-API/20220421-035024
        git checkout 65e00db0913a4019c3158e31aa6b2fd2c28ba03f
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash arch/arm64/kernel/ drivers/acpi/arm64/ sound/drivers/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> sound/drivers/serial-generic.c:192:6: warning: no previous prototype for function 'snd_serial_generic_write_wakeup' [-Wmissing-prototypes]
   void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
        ^
   sound/drivers/serial-generic.c:192:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
   void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
   ^
   static 
   1 warning generated.


vim +/snd_serial_generic_write_wakeup +192 sound/drivers/serial-generic.c

   191	
 > 192	void snd_serial_generic_write_wakeup(struct serdev_device *serdev)
   193	{
   194		struct snd_serial_generic *drvdata = serdev_device_get_drvdata(serdev);
   195	
   196		if (!snd_rawmidi_transmit_empty(drvdata->midi_output))
   197			snd_serial_generic_output_write(drvdata->midi_output);
   198	}
   199	

-- 
0-DAY CI Kernel Test Service
https://01.org/lkp