[PATCH v2 0/8] arm64: dts: qcom: initial Inforce IFC6560 board support

From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Rob Clark <robdclark@gmail.com>, Sean Paul <sean@poorly.run>,
	Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Stephen Boyd <swboyd@chromium.org>,
	David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	linux-arm-msm@vger.kernel.org, dri-devel@lists.freedesktop.org,
	freedreno@lists.freedesktop.org
Subject: [PATCH v2 0/8] arm64: dts: qcom: initial Inforce IFC6560 board support
Date: Fri, 13 May 2022 02:36:39 +0300	[thread overview]
Message-ID: <20220512233647.2672813-1-dmitry.baryshkov@linaro.org> (raw)

This work is largely based on the previous work by Bjorn Andersson ([1])

Changes since v1 (mostly based on Kondrad's review):
- Also disabled dsi0/dsi0 phy in sdm630.dtsi
- Removed the clock from BAM DMA devices rather than disabling them
  completely
- Replaced numbers with symbolic names for interconnects in sdm630.dtsi
- Switched to "qcom,sda660" as a fallback compatible string
- Added dt-bindings for the qcom,sda660 compat
- Removed extra nesting level from the adsp firmware path
- Replaced numbers with proper symbolic names in the board file
- Added chassis-type property
- Changed the order of blsp entries in the board file
- Removed spurious newlines
- Changed the order of regulator properties
- Changed the DSI data-lines to list all four lanes. Still use just
  three lanes for the adv bridge (and describe the reason in the
  comment)

Changes since Bjorn's v2:
- Disable dsi1, dsi1 phy, GPU by default in sdm660.dtsi/sdm630.dtsi
- Fix qusb2phy ref clock
- Added USB2 host support to sdm630.dtsi
- Renamed DTS to follow SoC-vendor-board pattern
- Fixed vph_pwr voltage
- Removed extra/unrelated comments
- Added keys, USB2, USB3,
- Added configuration for the attached HDMI bridge
- Enabled MDP, MDSS and DSI0/DSI0 PHY devices
- Removed uart pinctrl and /reserved-mem nodes (present in main dtsi
  file)
- Added card detection for the SDCC2
- Disabled BLSP BAM DMA devices, they make the board reset during boot

[1] https://lore.kernel.org/linux-arm-msm/20210825221110.1498718-1-bjorn.andersson@linaro.org/#t

Dmitry Baryshkov (8):
  arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default
  arm64: dts: qcom: sdm630: disable dsi1/dsi1_phy by default
  arm64: dts: qcom: sdm630: disable GPU by default
  arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
  arm64: dts: qcom: sdm630: add second (HS) USB host support
  arm64: dts: qcom: sdm630: use defined symbols for interconnects
  arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support
  dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board

 .../devicetree/bindings/arm/qcom.yaml         |   6 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sda660-inforce-ifc6560.dts  | 459 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/sdm630.dtsi          |  85 +++-
 arch/arm64/boot/dts/qcom/sdm660.dtsi          |   3 +
 5 files changed, 542 insertions(+), 12 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts

-- 
2.35.1