All of lore.kernel.org
 help / color / mirror / Atom feed
From: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
To: jic23@kernel.org, lars@metafoo.de, robh+dt@kernel.org,
	tomas.melin@vaisala.com, andy.shevchenko@gmail.com,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	Qing-wu.Li@leica-geosystems.com.cn
Cc: linux-iio@vger.kernel.org
Subject: [PATCH V7 4/5] iio: accel: sca3300: Add support for SCL3300
Date: Sun, 22 May 2022 07:04:18 +0000	[thread overview]
Message-ID: <20220522070419.409556-5-Qing-wu.Li@leica-geosystems.com.cn> (raw)
In-Reply-To: <20220522070419.409556-1-Qing-wu.Li@leica-geosystems.com.cn>

Add support for Murata SCL3300, a 3-axis MEMS accelerometer.
Same as SCA3300, it has the accelerometer and temperature output.

Datasheet: www.murata.com/en-us/products/sensor/inclinometer/overview/lineup/scl3300
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
---
 drivers/iio/accel/sca3300.c | 28 ++++++++++++++++++++++++++--
 1 file changed, 26 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/accel/sca3300.c b/drivers/iio/accel/sca3300.c
index e57aba79c32b..10bedb14d4f0 100644
--- a/drivers/iio/accel/sca3300.c
+++ b/drivers/iio/accel/sca3300.c
@@ -38,6 +38,7 @@
 /* Device ID */
 #define SCA3300_REG_WHOAMI	0x10
 #define SCA3300_WHOAMI_ID	0x51
+#define SCL3300_WHOAMI_ID	0xC1
 
 /* Device return status and mask */
 #define SCA3300_VALUE_RS_ERROR	0x3
@@ -96,10 +97,18 @@ static const struct iio_chan_spec sca3300_channels[] = {
 static const int sca3300_lp_freq[] = {70, 10};
 static const int sca3300_lp_freq_map[] = {0, 0, 0, 1};
 
+static const int scl3300_lp_freq[] = {40, 70, 10};
+static const int scl3300_lp_freq_map[] = {0, 1, 2};
+
 static const int sca3300_accel_scale[][2] = {{0, 370}, {0, 741}, {0, 185}};
 static const int sca3300_accel_scale_map[] = {0, 1, 2, 2};
 
+static const int scl3300_accel_scale[][2] = {{0, 167}, {0, 333}, {0, 83}};
+static const int scl3300_accel_scale_map[] = {0, 1, 2};
+
 static const int sca3300_avail_modes_map[] = {0, 1, 2, 3};
+static const int scl3300_avail_modes_map[] = {0, 1, 3};
+
 static const unsigned long sca3300_scan_masks[] = {
 	BIT(SCA3300_ACC_X) | BIT(SCA3300_ACC_Y) | BIT(SCA3300_ACC_Z) |
 	BIT(SCA3300_TEMP),
@@ -159,6 +168,20 @@ static const struct sca3300_chip_info sca3300_chip_tbl[] = {
 		.num_avail_modes = 4,
 		.chip_id = SCA3300_WHOAMI_ID,
 	},
+	{	.scan_masks = sca3300_scan_masks,
+		.channels = sca3300_channels,
+		.num_channels = ARRAY_SIZE(sca3300_channels),
+		.num_accel_scales = ARRAY_SIZE(scl3300_accel_scale)*2,
+		.accel_scale = scl3300_accel_scale,
+		.accel_scale_map = scl3300_accel_scale_map,
+		.num_freqs = ARRAY_SIZE(scl3300_lp_freq),
+		.freq_table = scl3300_lp_freq,
+		.freq_map = scl3300_lp_freq_map,
+		.name = "scl3300",
+		.avail_modes_table = scl3300_avail_modes_map,
+		.num_avail_modes = 3,
+		.chip_id = SCL3300_WHOAMI_ID,
+	},
 };
 
 DECLARE_CRC8_TABLE(sca3300_crc_table);
@@ -444,9 +467,9 @@ static int sca3300_init(struct sca3300_data *sca_data,
 
 	/*
 	 * Wait 1ms after SW-reset command.
-	 * Wait 15ms for settling of signal paths.
+	 * Wait 25ms for settling of signal paths.
 	 */
-	usleep_range(16e3, 50e3);
+	usleep_range(26e3, 50e3);
 
 	ret = sca3300_read_reg(sca_data, SCA3300_REG_WHOAMI, &value);
 	if (ret)
@@ -573,6 +596,7 @@ static int sca3300_probe(struct spi_device *spi)
 
 static const struct of_device_id sca3300_dt_ids[] = {
 	{ .compatible = "murata,sca3300"},
+	{ .compatible = "murata,scl3300"},
 	{}
 };
 MODULE_DEVICE_TABLE(of, sca3300_dt_ids);
-- 
2.25.1


  parent reply	other threads:[~2022-05-22  7:04 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-05-22  7:04 [PATCH V7 0/5] iio: accel: sca3300: add compatible for scl3300 LI Qingwu
2022-05-22  7:04 ` [PATCH V7 1/5] dt-bindings: iio: accel: sca3300: Document murata,scl3300 LI Qingwu
2022-05-22  7:04 ` [PATCH V7 2/5] iio: accel: sca3300: add define for temp channel for reuse LI Qingwu
2022-05-22  7:04 ` [PATCH V7 3/5] iio: accel: sca3300: modified to support multi chips LI Qingwu
2022-05-22  7:04 ` LI Qingwu [this message]
2022-05-22  7:48   ` [PATCH V7 4/5] iio: accel: sca3300: Add support for SCL3300 Christophe JAILLET
2022-05-22 11:12   ` Jonathan Cameron
2022-05-22  7:04 ` [PATCH V7 5/5] iio: accel: sca3300: Add inclination channels LI Qingwu
2022-05-22 11:17   ` Jonathan Cameron
2022-05-22 13:23     ` LI Qingwu
2022-05-23  3:14       ` LI Qingwu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220522070419.409556-5-Qing-wu.Li@leica-geosystems.com.cn \
    --to=qing-wu.li@leica-geosystems.com.cn \
    --cc=andy.shevchenko@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=jic23@kernel.org \
    --cc=lars@metafoo.de \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=tomas.melin@vaisala.com \
    --subject='Re: [PATCH V7 4/5] iio: accel: sca3300: Add support for SCL3300' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.