[PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

This patchset includes the following fixes:

- Add dt-bindings description for NPCM845.
- Bug fix for timeout calculation.
- Better handling of spurious interrupts.
- Fix for event type in slave mode.
- Removal of own slave addresses [2:10].
- Support for next gen BMC (NPCM845).

The NPCM I2C driver is tested on NPCM750 and NPCM845 evaluation boards.

Addressed comments from:
 - Wolfram Sang : https://lkml.org/lkml/2022/5/21/51

Changes since version 5:
 - Shorten npcm_i2caddr array since the number of supported i2c slave
   addresses is reduced.
 - Create a new patch from the original PATCH v5 08/10 to modify the slave
   transaction logic.

Changes since version 4:
 - Remove quotes around ref handle to nuvoton,sys-mgr in i2c binding
   document.
 - Keep the "longer line first" order.
 - Correct the SoB chain.
 - Modify the if statement in one line and add new line characters.
 - Modify the commit message format in the patch Remove own slave
   addresses 2:10. Correct the if statement in one line and shorten the
   debug messages.
 - Create a new patch to capitalize the one-line comment in the driver.

Changes since version 3:
 - Correct the const format in if condition in i2c binding document.
 - Add the oops message statement and register information in register
   access width patch.
 - Add the occurring rate of the i2c spurious interrupt issue and more
   details in driver's behavior to overcome this issue.
 - Address Andy's comments in the patch to support NPCM845.
 
Changes since version 2:
 - Keep old code as fallback, if getting nuvoton,sys-mgr property fails.
 - Fix the error reported by running 'make DT_CHECKER_FLAGS=-m 
   dt_binding_check'.
 - Make nuvoton,sys-mgr required for nuvoton,npcm845-i2c.
 - Correct the patch's subject about changing the way of getting GCR
   regmap and add the description about keeping old code as fallback
   if getting nuvoton,sys-mgr property fails.
 - Correct the patch title and description about removing the unused 
   variable clk_regmap.
 - Use the data field directly instead of the macros since macros are
   not constants anymore in this patch.
 
Changes since version 1:
 - Add nuvoton,sys-mgr property in NPCM devicetree.
 - Describe the commit message in imperative mood.
 - Modify the description in i2c binding document to cover NPCM series.
 - Add new property in i2c binding document.
 - Create a new patch for client address calculation.
 - Create a new patch for updating gcr property name.
 - Create a new patch for removing unused clock node.
 - Explain EOB in the commit description.
 - Create a new patch for correcting NPCM register access width.
 - Remove some comment since the corresponding logic no longer exists.
 - Remove fixes tag while the patch adds an additional feature.
 - Use devicetree data field to support NPCM845.

Tali Perry (2):
  i2c: npcm: Remove own slave addresses 2:10
  i2c: npcm: Correct slave role behavior

Tyrone Ting (3):
  dt-bindings: i2c: npcm: support NPCM845
  i2c: npcm: Support NPCM845
  i2c: npcm: Capitalize the one-line comment

 .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     |  25 ++-
 drivers/i2c/busses/Kconfig                    |   8 +-
 drivers/i2c/busses/Makefile                   |   2 +-
 drivers/i2c/busses/i2c-npcm7xx.c              | 176 ++++++++++--------
 4 files changed, 124 insertions(+), 87 deletions(-)

-- 
2.17.1

[PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

This patchset includes the following fixes:

- Add dt-bindings description for NPCM845.
- Bug fix for timeout calculation.
- Better handling of spurious interrupts.
- Fix for event type in slave mode.
- Removal of own slave addresses [2:10].
- Support for next gen BMC (NPCM845).

The NPCM I2C driver is tested on NPCM750 and NPCM845 evaluation boards.

Addressed comments from:
 - Wolfram Sang : https://lkml.org/lkml/2022/5/21/51

Changes since version 5:
 - Shorten npcm_i2caddr array since the number of supported i2c slave
   addresses is reduced.
 - Create a new patch from the original PATCH v5 08/10 to modify the slave
   transaction logic.

Changes since version 4:
 - Remove quotes around ref handle to nuvoton,sys-mgr in i2c binding
   document.
 - Keep the "longer line first" order.
 - Correct the SoB chain.
 - Modify the if statement in one line and add new line characters.
 - Modify the commit message format in the patch Remove own slave
   addresses 2:10. Correct the if statement in one line and shorten the
   debug messages.
 - Create a new patch to capitalize the one-line comment in the driver.

Changes since version 3:
 - Correct the const format in if condition in i2c binding document.
 - Add the oops message statement and register information in register
   access width patch.
 - Add the occurring rate of the i2c spurious interrupt issue and more
   details in driver's behavior to overcome this issue.
 - Address Andy's comments in the patch to support NPCM845.
 
Changes since version 2:
 - Keep old code as fallback, if getting nuvoton,sys-mgr property fails.
 - Fix the error reported by running 'make DT_CHECKER_FLAGS=-m 
   dt_binding_check'.
 - Make nuvoton,sys-mgr required for nuvoton,npcm845-i2c.
 - Correct the patch's subject about changing the way of getting GCR
   regmap and add the description about keeping old code as fallback
   if getting nuvoton,sys-mgr property fails.
 - Correct the patch title and description about removing the unused 
   variable clk_regmap.
 - Use the data field directly instead of the macros since macros are
   not constants anymore in this patch.
 
Changes since version 1:
 - Add nuvoton,sys-mgr property in NPCM devicetree.
 - Describe the commit message in imperative mood.
 - Modify the description in i2c binding document to cover NPCM series.
 - Add new property in i2c binding document.
 - Create a new patch for client address calculation.
 - Create a new patch for updating gcr property name.
 - Create a new patch for removing unused clock node.
 - Explain EOB in the commit description.
 - Create a new patch for correcting NPCM register access width.
 - Remove some comment since the corresponding logic no longer exists.
 - Remove fixes tag while the patch adds an additional feature.
 - Use devicetree data field to support NPCM845.

Tali Perry (2):
  i2c: npcm: Remove own slave addresses 2:10
  i2c: npcm: Correct slave role behavior

Tyrone Ting (3):
  dt-bindings: i2c: npcm: support NPCM845
  i2c: npcm: Support NPCM845
  i2c: npcm: Capitalize the one-line comment

 .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     |  25 ++-
 drivers/i2c/busses/Kconfig                    |   8 +-
 drivers/i2c/busses/Makefile                   |   2 +-
 drivers/i2c/busses/i2c-npcm7xx.c              | 176 ++++++++++--------
 4 files changed, 124 insertions(+), 87 deletions(-)

-- 
2.17.1

[PATCH v6 1/5] dt-bindings: i2c: npcm: support NPCM845

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

Add compatible and nuvoton,sys-mgr description for NPCM i2c module.

Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     | 25 +++++++++++++++----
 1 file changed, 20 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml b/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml
index 128444942aec..09d2591e1fa3 100644
--- a/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml
@@ -7,17 +7,18 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: nuvoton NPCM7XX I2C Controller Device Tree Bindings
 
 description: |
-  The NPCM750x includes sixteen I2C bus controllers. All Controllers support
-  both master and slave mode. Each controller can switch between master and slave
-  at run time (i.e. IPMB mode). Each controller has two 16 byte HW FIFO for TX and
-  RX.
+  I2C bus controllers of the NPCM series support both master and
+  slave mode. Each controller can switch between master and slave at run time
+  (i.e. IPMB mode). HW FIFO for TX and RX are supported.
 
 maintainers:
   - Tali Perry <tali.perry1@gmail.com>
 
 properties:
   compatible:
-    const: nuvoton,npcm750-i2c
+    enum:
+      - nuvoton,npcm750-i2c
+      - nuvoton,npcm845-i2c
 
   reg:
     maxItems: 1
@@ -36,6 +37,10 @@ properties:
     default: 100000
     enum: [100000, 400000, 1000000]
 
+  nuvoton,sys-mgr:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: The phandle of system manager register node.
+
 required:
   - compatible
   - reg
@@ -44,6 +49,15 @@ required:
 
 allOf:
   - $ref: /schemas/i2c/i2c-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: nuvoton,npcm845-i2c
+
+    then:
+      required:
+        - nuvoton,sys-mgr
 
 unevaluatedProperties: false
 
@@ -57,6 +71,7 @@ examples:
         clock-frequency = <100000>;
         interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
         compatible = "nuvoton,npcm750-i2c";
+        nuvoton,sys-mgr = <&gcr>;
     };
 
 ...
-- 
2.17.1

[PATCH v6 1/5] dt-bindings: i2c: npcm: support NPCM845

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

Add compatible and nuvoton,sys-mgr description for NPCM i2c module.

Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     | 25 +++++++++++++++----
 1 file changed, 20 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml b/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml
index 128444942aec..09d2591e1fa3 100644
--- a/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/nuvoton,npcm7xx-i2c.yaml
@@ -7,17 +7,18 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: nuvoton NPCM7XX I2C Controller Device Tree Bindings
 
 description: |
-  The NPCM750x includes sixteen I2C bus controllers. All Controllers support
-  both master and slave mode. Each controller can switch between master and slave
-  at run time (i.e. IPMB mode). Each controller has two 16 byte HW FIFO for TX and
-  RX.
+  I2C bus controllers of the NPCM series support both master and
+  slave mode. Each controller can switch between master and slave at run time
+  (i.e. IPMB mode). HW FIFO for TX and RX are supported.
 
 maintainers:
   - Tali Perry <tali.perry1@gmail.com>
 
 properties:
   compatible:
-    const: nuvoton,npcm750-i2c
+    enum:
+      - nuvoton,npcm750-i2c
+      - nuvoton,npcm845-i2c
 
   reg:
     maxItems: 1
@@ -36,6 +37,10 @@ properties:
     default: 100000
     enum: [100000, 400000, 1000000]
 
+  nuvoton,sys-mgr:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: The phandle of system manager register node.
+
 required:
   - compatible
   - reg
@@ -44,6 +49,15 @@ required:
 
 allOf:
   - $ref: /schemas/i2c/i2c-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: nuvoton,npcm845-i2c
+
+    then:
+      required:
+        - nuvoton,sys-mgr
 
 unevaluatedProperties: false
 
@@ -57,6 +71,7 @@ examples:
         clock-frequency = <100000>;
         interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
         compatible = "nuvoton,npcm750-i2c";
+        nuvoton,sys-mgr = <&gcr>;
     };
 
 ...
-- 
2.17.1

[PATCH v6 2/5] i2c: npcm: Remove own slave addresses 2:10

[Tyrone Ting]

From: Tali Perry <tali.perry1@gmail.com>

NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.

Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 41 +++++++++++++-------------------
 1 file changed, 16 insertions(+), 25 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index 5960ccde6574..b5cc83e51029 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -123,11 +123,11 @@ enum i2c_addr {
  * Since the addr regs are sprinkled all over the address space,
  * use this array to get the address or each register.
  */
-#define I2C_NUM_OWN_ADDR 10
+#define I2C_NUM_OWN_ADDR 2
+#define I2C_NUM_OWN_ADDR_SUPPORTED 2
+
 static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
-	NPCM_I2CADDR1, NPCM_I2CADDR2, NPCM_I2CADDR3, NPCM_I2CADDR4,
-	NPCM_I2CADDR5, NPCM_I2CADDR6, NPCM_I2CADDR7, NPCM_I2CADDR8,
-	NPCM_I2CADDR9, NPCM_I2CADDR10,
+	NPCM_I2CADDR1, NPCM_I2CADDR2,
 };
 #endif
 
@@ -392,14 +392,10 @@ static void npcm_i2c_disable(struct npcm_i2c *bus)
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	int i;
 
-	/* select bank 0 for I2C addresses */
-	npcm_i2c_select_bank(bus, I2C_BANK_0);
-
 	/* Slave addresses removal */
-	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR; i++)
+	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++)
 		iowrite8(0, bus->reg + npcm_i2caddr[i]);
 
-	npcm_i2c_select_bank(bus, I2C_BANK_1);
 #endif
 	/* Disable module */
 	i2cctl2 = ioread8(bus->reg + NPCM_I2CCTL2);
@@ -604,8 +600,7 @@ static int npcm_i2c_slave_enable(struct npcm_i2c *bus, enum i2c_addr addr_type,
 			i2cctl1 &= ~NPCM_I2CCTL1_GCMEN;
 		iowrite8(i2cctl1, bus->reg + NPCM_I2CCTL1);
 		return 0;
-	}
-	if (addr_type == I2C_ARP_ADDR) {
+	} else if (addr_type == I2C_ARP_ADDR) {
 		i2cctl3 = ioread8(bus->reg + NPCM_I2CCTL3);
 		if (enable)
 			i2cctl3 |= I2CCTL3_ARPMEN;
@@ -614,16 +609,16 @@ static int npcm_i2c_slave_enable(struct npcm_i2c *bus, enum i2c_addr addr_type,
 		iowrite8(i2cctl3, bus->reg + NPCM_I2CCTL3);
 		return 0;
 	}
+	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
+		dev_err(bus->dev, "try to enable more than 2 SA not supported\n");
+
 	if (addr_type >= I2C_ARP_ADDR)
 		return -EFAULT;
-	/* select bank 0 for address 3 to 10 */
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_0);
+
 	/* Set and enable the address */
 	iowrite8(sa_reg, bus->reg + npcm_i2caddr[addr_type]);
 	npcm_i2c_slave_int_enable(bus, enable);
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_1);
+
 	return 0;
 }
 #endif
@@ -846,15 +841,11 @@ static u8 npcm_i2c_get_slave_addr(struct npcm_i2c *bus, enum i2c_addr addr_type)
 {
 	u8 slave_add;
 
-	/* select bank 0 for address 3 to 10 */
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_0);
+	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
+		dev_err(bus->dev, "get slave: try to use more than 2 SA not supported\n");
 
 	slave_add = ioread8(bus->reg + npcm_i2caddr[(int)addr_type]);
 
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_1);
-
 	return slave_add;
 }
 
@@ -864,12 +855,12 @@ static int npcm_i2c_remove_slave_addr(struct npcm_i2c *bus, u8 slave_add)
 
 	/* Set the enable bit */
 	slave_add |= 0x80;
-	npcm_i2c_select_bank(bus, I2C_BANK_0);
-	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR; i++) {
+
+	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++) {
 		if (ioread8(bus->reg + npcm_i2caddr[i]) == slave_add)
 			iowrite8(0, bus->reg + npcm_i2caddr[i]);
 	}
-	npcm_i2c_select_bank(bus, I2C_BANK_1);
+
 	return 0;
 }
 
-- 
2.17.1

[PATCH v6 2/5] i2c: npcm: Remove own slave addresses 2:10

[Tyrone Ting]

From: Tali Perry <tali.perry1@gmail.com>

NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.

Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 41 +++++++++++++-------------------
 1 file changed, 16 insertions(+), 25 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index 5960ccde6574..b5cc83e51029 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -123,11 +123,11 @@ enum i2c_addr {
  * Since the addr regs are sprinkled all over the address space,
  * use this array to get the address or each register.
  */
-#define I2C_NUM_OWN_ADDR 10
+#define I2C_NUM_OWN_ADDR 2
+#define I2C_NUM_OWN_ADDR_SUPPORTED 2
+
 static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
-	NPCM_I2CADDR1, NPCM_I2CADDR2, NPCM_I2CADDR3, NPCM_I2CADDR4,
-	NPCM_I2CADDR5, NPCM_I2CADDR6, NPCM_I2CADDR7, NPCM_I2CADDR8,
-	NPCM_I2CADDR9, NPCM_I2CADDR10,
+	NPCM_I2CADDR1, NPCM_I2CADDR2,
 };
 #endif
 
@@ -392,14 +392,10 @@ static void npcm_i2c_disable(struct npcm_i2c *bus)
 #if IS_ENABLED(CONFIG_I2C_SLAVE)
 	int i;
 
-	/* select bank 0 for I2C addresses */
-	npcm_i2c_select_bank(bus, I2C_BANK_0);
-
 	/* Slave addresses removal */
-	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR; i++)
+	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++)
 		iowrite8(0, bus->reg + npcm_i2caddr[i]);
 
-	npcm_i2c_select_bank(bus, I2C_BANK_1);
 #endif
 	/* Disable module */
 	i2cctl2 = ioread8(bus->reg + NPCM_I2CCTL2);
@@ -604,8 +600,7 @@ static int npcm_i2c_slave_enable(struct npcm_i2c *bus, enum i2c_addr addr_type,
 			i2cctl1 &= ~NPCM_I2CCTL1_GCMEN;
 		iowrite8(i2cctl1, bus->reg + NPCM_I2CCTL1);
 		return 0;
-	}
-	if (addr_type == I2C_ARP_ADDR) {
+	} else if (addr_type == I2C_ARP_ADDR) {
 		i2cctl3 = ioread8(bus->reg + NPCM_I2CCTL3);
 		if (enable)
 			i2cctl3 |= I2CCTL3_ARPMEN;
@@ -614,16 +609,16 @@ static int npcm_i2c_slave_enable(struct npcm_i2c *bus, enum i2c_addr addr_type,
 		iowrite8(i2cctl3, bus->reg + NPCM_I2CCTL3);
 		return 0;
 	}
+	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
+		dev_err(bus->dev, "try to enable more than 2 SA not supported\n");
+
 	if (addr_type >= I2C_ARP_ADDR)
 		return -EFAULT;
-	/* select bank 0 for address 3 to 10 */
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_0);
+
 	/* Set and enable the address */
 	iowrite8(sa_reg, bus->reg + npcm_i2caddr[addr_type]);
 	npcm_i2c_slave_int_enable(bus, enable);
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_1);
+
 	return 0;
 }
 #endif
@@ -846,15 +841,11 @@ static u8 npcm_i2c_get_slave_addr(struct npcm_i2c *bus, enum i2c_addr addr_type)
 {
 	u8 slave_add;
 
-	/* select bank 0 for address 3 to 10 */
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_0);
+	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
+		dev_err(bus->dev, "get slave: try to use more than 2 SA not supported\n");
 
 	slave_add = ioread8(bus->reg + npcm_i2caddr[(int)addr_type]);
 
-	if (addr_type > I2C_SLAVE_ADDR2)
-		npcm_i2c_select_bank(bus, I2C_BANK_1);
-
 	return slave_add;
 }
 
@@ -864,12 +855,12 @@ static int npcm_i2c_remove_slave_addr(struct npcm_i2c *bus, u8 slave_add)
 
 	/* Set the enable bit */
 	slave_add |= 0x80;
-	npcm_i2c_select_bank(bus, I2C_BANK_0);
-	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR; i++) {
+
+	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++) {
 		if (ioread8(bus->reg + npcm_i2caddr[i]) == slave_add)
 			iowrite8(0, bus->reg + npcm_i2caddr[i]);
 	}
-	npcm_i2c_select_bank(bus, I2C_BANK_1);
+
 	return 0;
 }
 
-- 
2.17.1

[PATCH v6 3/5] i2c: npcm: Correct slave role behavior

[Tyrone Ting]

From: Tali Perry <tali.perry1@gmail.com>

Correct the slave transaction logic to be compatible with the generic
slave backend driver.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index b5cc83e51029..b4d218c6c8fb 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -915,11 +915,15 @@ static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
 	for (i = 0; i < I2C_HW_FIFO_SIZE; i++) {
 		if (bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
 			break;
-		i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+		if (bus->state == I2C_SLAVE_MATCH) {
+			i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+			bus->state = I2C_OPER_STARTED;
+		} else {
+			i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
+		}
 		ind = (bus->slv_wr_ind + bus->slv_wr_size) % I2C_HW_FIFO_SIZE;
 		bus->slv_wr_buf[ind] = value;
 		bus->slv_wr_size++;
-		i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
 	}
 	return I2C_HW_FIFO_SIZE - ret;
 }
@@ -967,7 +971,6 @@ static void npcm_i2c_slave_xmit(struct npcm_i2c *bus, u16 nwrite,
 	if (nwrite == 0)
 		return;
 
-	bus->state = I2C_OPER_STARTED;
 	bus->operation = I2C_WRITE_OPER;
 
 	/* get the next buffer */
-- 
2.17.1

[PATCH v6 3/5] i2c: npcm: Correct slave role behavior

[Tyrone Ting]

From: Tali Perry <tali.perry1@gmail.com>

Correct the slave transaction logic to be compatible with the generic
slave backend driver.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index b5cc83e51029..b4d218c6c8fb 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -915,11 +915,15 @@ static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
 	for (i = 0; i < I2C_HW_FIFO_SIZE; i++) {
 		if (bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
 			break;
-		i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+		if (bus->state == I2C_SLAVE_MATCH) {
+			i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
+			bus->state = I2C_OPER_STARTED;
+		} else {
+			i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
+		}
 		ind = (bus->slv_wr_ind + bus->slv_wr_size) % I2C_HW_FIFO_SIZE;
 		bus->slv_wr_buf[ind] = value;
 		bus->slv_wr_size++;
-		i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
 	}
 	return I2C_HW_FIFO_SIZE - ret;
 }
@@ -967,7 +971,6 @@ static void npcm_i2c_slave_xmit(struct npcm_i2c *bus, u16 nwrite,
 	if (nwrite == 0)
 		return;
 
-	bus->state = I2C_OPER_STARTED;
 	bus->operation = I2C_WRITE_OPER;
 
 	/* get the next buffer */
-- 
2.17.1

[PATCH v6 4/5] i2c: npcm: Support NPCM845

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

Add NPCM8XX I2C support.
The NPCM8XX uses a similar i2c module as NPCM7XX.
The internal HW FIFO is larger in NPCM8XX.

Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Acked-by: Tomer Maimon <tmaimon77@gmail.com>
---
 drivers/i2c/busses/Kconfig       |   8 +--
 drivers/i2c/busses/Makefile      |   2 +-
 drivers/i2c/busses/i2c-npcm7xx.c | 114 +++++++++++++++++++------------
 3 files changed, 76 insertions(+), 48 deletions(-)

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index a1bae59208e3..b1d7069dd377 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -838,13 +838,13 @@ config I2C_NOMADIK
 	  I2C interface from ST-Ericsson's Nomadik and Ux500 architectures,
 	  as well as the STA2X11 PCIe I/O HUB.
 
-config I2C_NPCM7XX
+config I2C_NPCM
 	tristate "Nuvoton I2C Controller"
-	depends on ARCH_NPCM7XX || COMPILE_TEST
+	depends on ARCH_NPCM || COMPILE_TEST
 	help
 	  If you say yes to this option, support will be included for the
-	  Nuvoton I2C controller, which is available on the NPCM7xx BMC
-	  controller.
+	  Nuvoton I2C controller, which is available on the NPCM BMC
+	  controllers.
 	  Driver can also support slave mode (select I2C_SLAVE).
 
 config I2C_OCORES
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 479f60e4ee3d..b0a10e5d9ee9 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -84,7 +84,7 @@ obj-$(CONFIG_I2C_MT7621)	+= i2c-mt7621.o
 obj-$(CONFIG_I2C_MV64XXX)	+= i2c-mv64xxx.o
 obj-$(CONFIG_I2C_MXS)		+= i2c-mxs.o
 obj-$(CONFIG_I2C_NOMADIK)	+= i2c-nomadik.o
-obj-$(CONFIG_I2C_NPCM7XX)	+= i2c-npcm7xx.o
+obj-$(CONFIG_I2C_NPCM)		+= i2c-npcm7xx.o
 obj-$(CONFIG_I2C_OCORES)	+= i2c-ocores.o
 obj-$(CONFIG_I2C_OMAP)		+= i2c-omap.o
 obj-$(CONFIG_I2C_OWL)		+= i2c-owl.o
diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index b4d218c6c8fb..86fd942ea648 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -17,6 +17,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 
@@ -91,7 +92,6 @@ enum i2c_addr {
 
 /* init register and default value required to enable module */
 #define NPCM_I2CSEGCTL			0xE4
-#define NPCM_I2CSEGCTL_INIT_VAL		0x0333F000
 
 /* Common regs */
 #define NPCM_I2CSDA			0x00
@@ -226,8 +226,7 @@ static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
 #define NPCM_I2CFIF_CTS_CLR_FIFO	BIT(6)
 #define NPCM_I2CFIF_CTS_SLVRSTR		BIT(7)
 
-/* NPCM_I2CTXF_CTL reg fields */
-#define NPCM_I2CTXF_CTL_TX_THR		GENMASK(4, 0)
+/* NPCM_I2CTXF_CTL reg field */
 #define NPCM_I2CTXF_CTL_THR_TXIE	BIT(6)
 
 /* NPCM_I2CT_OUT reg fields */
@@ -236,22 +235,18 @@ static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
 #define NPCM_I2CT_OUT_T_OUTST		BIT(7)
 
 /* NPCM_I2CTXF_STS reg fields */
-#define NPCM_I2CTXF_STS_TX_BYTES	GENMASK(4, 0)
 #define NPCM_I2CTXF_STS_TX_THST		BIT(6)
 
 /* NPCM_I2CRXF_STS reg fields */
-#define NPCM_I2CRXF_STS_RX_BYTES	GENMASK(4, 0)
 #define NPCM_I2CRXF_STS_RX_THST		BIT(6)
 
 /* NPCM_I2CFIF_CTL reg fields */
 #define NPCM_I2CFIF_CTL_FIFO_EN		BIT(4)
 
 /* NPCM_I2CRXF_CTL reg fields */
-#define NPCM_I2CRXF_CTL_RX_THR		GENMASK(4, 0)
-#define NPCM_I2CRXF_CTL_LAST_PEC	BIT(5)
 #define NPCM_I2CRXF_CTL_THR_RXIE	BIT(6)
 
-#define I2C_HW_FIFO_SIZE		16
+#define MAX_I2C_HW_FIFO_SIZE		32
 
 /* I2C_VER reg fields */
 #define I2C_VER_VERSION			GENMASK(6, 0)
@@ -268,11 +263,36 @@ static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
 #define I2C_FREQ_MIN_HZ			10000
 #define I2C_FREQ_MAX_HZ			I2C_MAX_FAST_MODE_PLUS_FREQ
 
+struct npcm_i2c_data {
+	u8 fifo_size;
+	u32 segctl_init_val;
+	u8 txf_sts_tx_bytes;
+	u8 rxf_sts_rx_bytes;
+	u8 rxf_ctl_last_pec;
+};
+
+static const struct npcm_i2c_data npxm7xx_i2c_data = {
+	.fifo_size = 16,
+	.segctl_init_val = 0x0333F000,
+	.txf_sts_tx_bytes = GENMASK(4, 0),
+	.rxf_sts_rx_bytes = GENMASK(4, 0),
+	.rxf_ctl_last_pec = BIT(5),
+};
+
+static const struct npcm_i2c_data npxm8xx_i2c_data = {
+	.fifo_size = 32,
+	.segctl_init_val = 0x9333F000,
+	.txf_sts_tx_bytes = GENMASK(5, 0),
+	.rxf_sts_rx_bytes = GENMASK(5, 0),
+	.rxf_ctl_last_pec = BIT(7),
+};
+
 /* Status of one I2C module */
 struct npcm_i2c {
 	struct i2c_adapter adap;
 	struct device *dev;
 	unsigned char __iomem *reg;
+	const struct npcm_i2c_data *data;
 	spinlock_t lock;   /* IRQ synchronization */
 	struct completion cmd_complete;
 	int cmd_err;
@@ -305,8 +325,8 @@ struct npcm_i2c {
 	int slv_rd_ind;
 	int slv_wr_size;
 	int slv_wr_ind;
-	u8 slv_rd_buf[I2C_HW_FIFO_SIZE];
-	u8 slv_wr_buf[I2C_HW_FIFO_SIZE];
+	u8 slv_rd_buf[MAX_I2C_HW_FIFO_SIZE];
+	u8 slv_wr_buf[MAX_I2C_HW_FIFO_SIZE];
 #endif
 	struct dentry *debugfs; /* debugfs device directory */
 	u64 ber_cnt;
@@ -439,7 +459,7 @@ static inline bool npcm_i2c_tx_fifo_empty(struct npcm_i2c *bus)
 
 	tx_fifo_sts = ioread8(bus->reg + NPCM_I2CTXF_STS);
 	/* check if TX FIFO is not empty */
-	if ((tx_fifo_sts & NPCM_I2CTXF_STS_TX_BYTES) == 0)
+	if ((tx_fifo_sts & bus->data->txf_sts_tx_bytes) == 0)
 		return false;
 
 	/* check if TX FIFO status bit is set: */
@@ -452,7 +472,7 @@ static inline bool npcm_i2c_rx_fifo_full(struct npcm_i2c *bus)
 
 	rx_fifo_sts = ioread8(bus->reg + NPCM_I2CRXF_STS);
 	/* check if RX FIFO is not empty: */
-	if ((rx_fifo_sts & NPCM_I2CRXF_STS_RX_BYTES) == 0)
+	if ((rx_fifo_sts & bus->data->rxf_sts_rx_bytes) == 0)
 		return false;
 
 	/* check if rx fifo full status is set: */
@@ -739,11 +759,11 @@ static void npcm_i2c_callback(struct npcm_i2c *bus,
 static u8 npcm_i2c_fifo_usage(struct npcm_i2c *bus)
 {
 	if (bus->operation == I2C_WRITE_OPER)
-		return FIELD_GET(NPCM_I2CTXF_STS_TX_BYTES,
-				 ioread8(bus->reg + NPCM_I2CTXF_STS));
+		return (bus->data->txf_sts_tx_bytes &
+			ioread8(bus->reg + NPCM_I2CTXF_STS));
 	if (bus->operation == I2C_READ_OPER)
-		return FIELD_GET(NPCM_I2CRXF_STS_RX_BYTES,
-				 ioread8(bus->reg + NPCM_I2CRXF_STS));
+		return (bus->data->rxf_sts_rx_bytes &
+			ioread8(bus->reg + NPCM_I2CRXF_STS));
 	return 0;
 }
 
@@ -755,13 +775,13 @@ static void npcm_i2c_write_to_fifo_master(struct npcm_i2c *bus, u16 max_bytes)
 	 * Fill the FIFO, while the FIFO is not full and there are more bytes
 	 * to write
 	 */
-	size_free_fifo = I2C_HW_FIFO_SIZE - npcm_i2c_fifo_usage(bus);
+	size_free_fifo = bus->data->fifo_size - npcm_i2c_fifo_usage(bus);
 	while (max_bytes-- && size_free_fifo) {
 		if (bus->wr_ind < bus->wr_size)
 			npcm_i2c_wr_byte(bus, bus->wr_buf[bus->wr_ind++]);
 		else
 			npcm_i2c_wr_byte(bus, 0xFF);
-		size_free_fifo = I2C_HW_FIFO_SIZE - npcm_i2c_fifo_usage(bus);
+		size_free_fifo = bus->data->fifo_size - npcm_i2c_fifo_usage(bus);
 	}
 }
 
@@ -782,11 +802,11 @@ static void npcm_i2c_set_fifo(struct npcm_i2c *bus, int nread, int nwrite)
 
 	/* configure RX FIFO */
 	if (nread > 0) {
-		rxf_ctl = min_t(int, nread, I2C_HW_FIFO_SIZE);
+		rxf_ctl = min_t(int, nread, bus->data->fifo_size);
 
 		/* set LAST bit. if LAST is set next FIFO packet is nacked */
-		if (nread <= I2C_HW_FIFO_SIZE)
-			rxf_ctl |= NPCM_I2CRXF_CTL_LAST_PEC;
+		if (nread <= bus->data->fifo_size)
+			rxf_ctl |= bus->data->rxf_ctl_last_pec;
 
 		/*
 		 * if we are about to read the first byte in blk rd mode,
@@ -804,9 +824,9 @@ static void npcm_i2c_set_fifo(struct npcm_i2c *bus, int nread, int nwrite)
 
 	/* configure TX FIFO */
 	if (nwrite > 0) {
-		if (nwrite > I2C_HW_FIFO_SIZE)
+		if (nwrite > bus->data->fifo_size)
 			/* data to send is more then FIFO size. */
-			iowrite8(I2C_HW_FIFO_SIZE, bus->reg + NPCM_I2CTXF_CTL);
+			iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CTXF_CTL);
 		else
 			iowrite8(nwrite, bus->reg + NPCM_I2CTXF_CTL);
 
@@ -873,13 +893,13 @@ static void npcm_i2c_write_fifo_slave(struct npcm_i2c *bus, u16 max_bytes)
 	npcm_i2c_clear_fifo_int(bus);
 	npcm_i2c_clear_tx_fifo(bus);
 	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
-	while (max_bytes-- && I2C_HW_FIFO_SIZE != npcm_i2c_fifo_usage(bus)) {
+	while (max_bytes-- && bus->data->fifo_size != npcm_i2c_fifo_usage(bus)) {
 		if (bus->slv_wr_size <= 0)
 			break;
-		bus->slv_wr_ind = bus->slv_wr_ind % I2C_HW_FIFO_SIZE;
+		bus->slv_wr_ind = bus->slv_wr_ind & (bus->data->fifo_size - 1);
 		npcm_i2c_wr_byte(bus, bus->slv_wr_buf[bus->slv_wr_ind]);
 		bus->slv_wr_ind++;
-		bus->slv_wr_ind = bus->slv_wr_ind % I2C_HW_FIFO_SIZE;
+		bus->slv_wr_ind = bus->slv_wr_ind & (bus->data->fifo_size - 1);
 		bus->slv_wr_size--;
 	}
 }
@@ -894,7 +914,7 @@ static void npcm_i2c_read_fifo_slave(struct npcm_i2c *bus, u8 bytes_in_fifo)
 	while (bytes_in_fifo--) {
 		data = npcm_i2c_rd_byte(bus);
 
-		bus->slv_rd_ind = bus->slv_rd_ind % I2C_HW_FIFO_SIZE;
+		bus->slv_rd_ind = bus->slv_rd_ind & (bus->data->fifo_size - 1);
 		bus->slv_rd_buf[bus->slv_rd_ind] = data;
 		bus->slv_rd_ind++;
 
@@ -912,8 +932,8 @@ static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
 	int ret = bus->slv_wr_ind;
 
 	/* fill a cyclic buffer */
-	for (i = 0; i < I2C_HW_FIFO_SIZE; i++) {
-		if (bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
+	for (i = 0; i < bus->data->fifo_size; i++) {
+		if (bus->slv_wr_size >= bus->data->fifo_size)
 			break;
 		if (bus->state == I2C_SLAVE_MATCH) {
 			i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
@@ -921,11 +941,11 @@ static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
 		} else {
 			i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
 		}
-		ind = (bus->slv_wr_ind + bus->slv_wr_size) % I2C_HW_FIFO_SIZE;
+		ind = (bus->slv_wr_ind + bus->slv_wr_size) & (bus->data->fifo_size - 1);
 		bus->slv_wr_buf[ind] = value;
 		bus->slv_wr_size++;
 	}
-	return I2C_HW_FIFO_SIZE - ret;
+	return bus->data->fifo_size - ret;
 }
 
 static void npcm_i2c_slave_send_rd_buf(struct npcm_i2c *bus)
@@ -960,7 +980,7 @@ static void npcm_i2c_slave_receive(struct npcm_i2c *bus, u16 nread,
 	bus->slv_rd_ind = 0;
 
 	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
-	iowrite8(I2C_HW_FIFO_SIZE, bus->reg + NPCM_I2CRXF_CTL);
+	iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CRXF_CTL);
 	npcm_i2c_clear_tx_fifo(bus);
 	npcm_i2c_clear_rx_fifo(bus);
 }
@@ -993,12 +1013,12 @@ static void npcm_i2c_slave_wr_buf_sync(struct npcm_i2c *bus)
 {
 	int left_in_fifo;
 
-	left_in_fifo = FIELD_GET(NPCM_I2CTXF_STS_TX_BYTES,
-				 ioread8(bus->reg + NPCM_I2CTXF_STS));
+	left_in_fifo = bus->data->txf_sts_tx_bytes &
+			ioread8(bus->reg + NPCM_I2CTXF_STS);
 
 	/* fifo already full: */
-	if (left_in_fifo >= I2C_HW_FIFO_SIZE ||
-	    bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
+	if (left_in_fifo >= bus->data->fifo_size ||
+	    bus->slv_wr_size >= bus->data->fifo_size)
 		return;
 
 	/* update the wr fifo index back to the untransmitted bytes: */
@@ -1006,7 +1026,7 @@ static void npcm_i2c_slave_wr_buf_sync(struct npcm_i2c *bus)
 	bus->slv_wr_size = bus->slv_wr_size + left_in_fifo;
 
 	if (bus->slv_wr_ind < 0)
-		bus->slv_wr_ind += I2C_HW_FIFO_SIZE;
+		bus->slv_wr_ind += bus->data->fifo_size;
 }
 
 static void npcm_i2c_slave_rd_wr(struct npcm_i2c *bus)
@@ -1152,7 +1172,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
 		npcm_i2c_clear_rx_fifo(bus);
 		npcm_i2c_clear_tx_fifo(bus);
 		iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
-		iowrite8(I2C_HW_FIFO_SIZE, bus->reg + NPCM_I2CRXF_CTL);
+		iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CRXF_CTL);
 		if (NPCM_I2CST_XMIT & i2cst) {
 			bus->operation = I2C_WRITE_OPER;
 		} else {
@@ -1313,8 +1333,8 @@ static void npcm_i2c_master_fifo_read(struct npcm_i2c *bus)
 	 * read == FIFO Size + C (where C < FIFO Size)then first read C bytes
 	 * and in the next int we read rest of the data.
 	 */
-	if (rcount < (2 * I2C_HW_FIFO_SIZE) && rcount > I2C_HW_FIFO_SIZE)
-		fifo_bytes = rcount - I2C_HW_FIFO_SIZE;
+	if (rcount < (2 * bus->data->fifo_size) && rcount > bus->data->fifo_size)
+		fifo_bytes = rcount - bus->data->fifo_size;
 
 	if (rcount <= fifo_bytes) {
 		/* last bytes are about to be read - end of tx */
@@ -2193,7 +2213,7 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 	 * It cannot be cleared without resetting the module.
 	 */
 	else if (bus->cmd_err &&
-		 (NPCM_I2CRXF_CTL_LAST_PEC & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
+		 (bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
 		npcm_i2c_reset(bus);
 
 	/* after any xfer, successful or not, stall and EOB must be disabled */
@@ -2262,6 +2282,7 @@ static int npcm_i2c_probe_bus(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
 	static struct regmap *gcr_regmap;
+	struct device *dev = &pdev->dev;
 	struct i2c_adapter *adap;
 	struct npcm_i2c *bus;
 	struct clk *i2c_clk;
@@ -2274,6 +2295,12 @@ static int npcm_i2c_probe_bus(struct platform_device *pdev)
 
 	bus->dev = &pdev->dev;
 
+	bus->data = of_device_get_match_data(dev);
+	if (!bus->data) {
+		dev_err(dev, "OF data missing\n");
+		return -EINVAL;
+	}
+
 	bus->num = of_alias_get_id(pdev->dev.of_node, "i2c");
 	/* core clk must be acquired to calculate module timing settings */
 	i2c_clk = devm_clk_get(&pdev->dev, NULL);
@@ -2287,7 +2314,7 @@ static int npcm_i2c_probe_bus(struct platform_device *pdev)
 
 	if (IS_ERR(gcr_regmap))
 		return PTR_ERR(gcr_regmap);
-	regmap_write(gcr_regmap, NPCM_I2CSEGCTL, NPCM_I2CSEGCTL_INIT_VAL);
+	regmap_write(gcr_regmap, NPCM_I2CSEGCTL, bus->data->segctl_init_val);
 
 	bus->reg = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(bus->reg))
@@ -2349,7 +2376,8 @@ static int npcm_i2c_remove_bus(struct platform_device *pdev)
 }
 
 static const struct of_device_id npcm_i2c_bus_of_table[] = {
-	{ .compatible = "nuvoton,npcm750-i2c", },
+	{ .compatible = "nuvoton,npcm750-i2c", .data = &npxm7xx_i2c_data },
+	{ .compatible = "nuvoton,npcm845-i2c", .data = &npxm8xx_i2c_data },
 	{}
 };
 MODULE_DEVICE_TABLE(of, npcm_i2c_bus_of_table);
-- 
2.17.1

[PATCH v6 4/5] i2c: npcm: Support NPCM845

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

Add NPCM8XX I2C support.
The NPCM8XX uses a similar i2c module as NPCM7XX.
The internal HW FIFO is larger in NPCM8XX.

Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Acked-by: Tomer Maimon <tmaimon77@gmail.com>
---
 drivers/i2c/busses/Kconfig       |   8 +--
 drivers/i2c/busses/Makefile      |   2 +-
 drivers/i2c/busses/i2c-npcm7xx.c | 114 +++++++++++++++++++------------
 3 files changed, 76 insertions(+), 48 deletions(-)

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index a1bae59208e3..b1d7069dd377 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -838,13 +838,13 @@ config I2C_NOMADIK
 	  I2C interface from ST-Ericsson's Nomadik and Ux500 architectures,
 	  as well as the STA2X11 PCIe I/O HUB.
 
-config I2C_NPCM7XX
+config I2C_NPCM
 	tristate "Nuvoton I2C Controller"
-	depends on ARCH_NPCM7XX || COMPILE_TEST
+	depends on ARCH_NPCM || COMPILE_TEST
 	help
 	  If you say yes to this option, support will be included for the
-	  Nuvoton I2C controller, which is available on the NPCM7xx BMC
-	  controller.
+	  Nuvoton I2C controller, which is available on the NPCM BMC
+	  controllers.
 	  Driver can also support slave mode (select I2C_SLAVE).
 
 config I2C_OCORES
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 479f60e4ee3d..b0a10e5d9ee9 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -84,7 +84,7 @@ obj-$(CONFIG_I2C_MT7621)	+= i2c-mt7621.o
 obj-$(CONFIG_I2C_MV64XXX)	+= i2c-mv64xxx.o
 obj-$(CONFIG_I2C_MXS)		+= i2c-mxs.o
 obj-$(CONFIG_I2C_NOMADIK)	+= i2c-nomadik.o
-obj-$(CONFIG_I2C_NPCM7XX)	+= i2c-npcm7xx.o
+obj-$(CONFIG_I2C_NPCM)		+= i2c-npcm7xx.o
 obj-$(CONFIG_I2C_OCORES)	+= i2c-ocores.o
 obj-$(CONFIG_I2C_OMAP)		+= i2c-omap.o
 obj-$(CONFIG_I2C_OWL)		+= i2c-owl.o
diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index b4d218c6c8fb..86fd942ea648 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -17,6 +17,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 
@@ -91,7 +92,6 @@ enum i2c_addr {
 
 /* init register and default value required to enable module */
 #define NPCM_I2CSEGCTL			0xE4
-#define NPCM_I2CSEGCTL_INIT_VAL		0x0333F000
 
 /* Common regs */
 #define NPCM_I2CSDA			0x00
@@ -226,8 +226,7 @@ static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
 #define NPCM_I2CFIF_CTS_CLR_FIFO	BIT(6)
 #define NPCM_I2CFIF_CTS_SLVRSTR		BIT(7)
 
-/* NPCM_I2CTXF_CTL reg fields */
-#define NPCM_I2CTXF_CTL_TX_THR		GENMASK(4, 0)
+/* NPCM_I2CTXF_CTL reg field */
 #define NPCM_I2CTXF_CTL_THR_TXIE	BIT(6)
 
 /* NPCM_I2CT_OUT reg fields */
@@ -236,22 +235,18 @@ static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
 #define NPCM_I2CT_OUT_T_OUTST		BIT(7)
 
 /* NPCM_I2CTXF_STS reg fields */
-#define NPCM_I2CTXF_STS_TX_BYTES	GENMASK(4, 0)
 #define NPCM_I2CTXF_STS_TX_THST		BIT(6)
 
 /* NPCM_I2CRXF_STS reg fields */
-#define NPCM_I2CRXF_STS_RX_BYTES	GENMASK(4, 0)
 #define NPCM_I2CRXF_STS_RX_THST		BIT(6)
 
 /* NPCM_I2CFIF_CTL reg fields */
 #define NPCM_I2CFIF_CTL_FIFO_EN		BIT(4)
 
 /* NPCM_I2CRXF_CTL reg fields */
-#define NPCM_I2CRXF_CTL_RX_THR		GENMASK(4, 0)
-#define NPCM_I2CRXF_CTL_LAST_PEC	BIT(5)
 #define NPCM_I2CRXF_CTL_THR_RXIE	BIT(6)
 
-#define I2C_HW_FIFO_SIZE		16
+#define MAX_I2C_HW_FIFO_SIZE		32
 
 /* I2C_VER reg fields */
 #define I2C_VER_VERSION			GENMASK(6, 0)
@@ -268,11 +263,36 @@ static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
 #define I2C_FREQ_MIN_HZ			10000
 #define I2C_FREQ_MAX_HZ			I2C_MAX_FAST_MODE_PLUS_FREQ
 
+struct npcm_i2c_data {
+	u8 fifo_size;
+	u32 segctl_init_val;
+	u8 txf_sts_tx_bytes;
+	u8 rxf_sts_rx_bytes;
+	u8 rxf_ctl_last_pec;
+};
+
+static const struct npcm_i2c_data npxm7xx_i2c_data = {
+	.fifo_size = 16,
+	.segctl_init_val = 0x0333F000,
+	.txf_sts_tx_bytes = GENMASK(4, 0),
+	.rxf_sts_rx_bytes = GENMASK(4, 0),
+	.rxf_ctl_last_pec = BIT(5),
+};
+
+static const struct npcm_i2c_data npxm8xx_i2c_data = {
+	.fifo_size = 32,
+	.segctl_init_val = 0x9333F000,
+	.txf_sts_tx_bytes = GENMASK(5, 0),
+	.rxf_sts_rx_bytes = GENMASK(5, 0),
+	.rxf_ctl_last_pec = BIT(7),
+};
+
 /* Status of one I2C module */
 struct npcm_i2c {
 	struct i2c_adapter adap;
 	struct device *dev;
 	unsigned char __iomem *reg;
+	const struct npcm_i2c_data *data;
 	spinlock_t lock;   /* IRQ synchronization */
 	struct completion cmd_complete;
 	int cmd_err;
@@ -305,8 +325,8 @@ struct npcm_i2c {
 	int slv_rd_ind;
 	int slv_wr_size;
 	int slv_wr_ind;
-	u8 slv_rd_buf[I2C_HW_FIFO_SIZE];
-	u8 slv_wr_buf[I2C_HW_FIFO_SIZE];
+	u8 slv_rd_buf[MAX_I2C_HW_FIFO_SIZE];
+	u8 slv_wr_buf[MAX_I2C_HW_FIFO_SIZE];
 #endif
 	struct dentry *debugfs; /* debugfs device directory */
 	u64 ber_cnt;
@@ -439,7 +459,7 @@ static inline bool npcm_i2c_tx_fifo_empty(struct npcm_i2c *bus)
 
 	tx_fifo_sts = ioread8(bus->reg + NPCM_I2CTXF_STS);
 	/* check if TX FIFO is not empty */
-	if ((tx_fifo_sts & NPCM_I2CTXF_STS_TX_BYTES) == 0)
+	if ((tx_fifo_sts & bus->data->txf_sts_tx_bytes) == 0)
 		return false;
 
 	/* check if TX FIFO status bit is set: */
@@ -452,7 +472,7 @@ static inline bool npcm_i2c_rx_fifo_full(struct npcm_i2c *bus)
 
 	rx_fifo_sts = ioread8(bus->reg + NPCM_I2CRXF_STS);
 	/* check if RX FIFO is not empty: */
-	if ((rx_fifo_sts & NPCM_I2CRXF_STS_RX_BYTES) == 0)
+	if ((rx_fifo_sts & bus->data->rxf_sts_rx_bytes) == 0)
 		return false;
 
 	/* check if rx fifo full status is set: */
@@ -739,11 +759,11 @@ static void npcm_i2c_callback(struct npcm_i2c *bus,
 static u8 npcm_i2c_fifo_usage(struct npcm_i2c *bus)
 {
 	if (bus->operation == I2C_WRITE_OPER)
-		return FIELD_GET(NPCM_I2CTXF_STS_TX_BYTES,
-				 ioread8(bus->reg + NPCM_I2CTXF_STS));
+		return (bus->data->txf_sts_tx_bytes &
+			ioread8(bus->reg + NPCM_I2CTXF_STS));
 	if (bus->operation == I2C_READ_OPER)
-		return FIELD_GET(NPCM_I2CRXF_STS_RX_BYTES,
-				 ioread8(bus->reg + NPCM_I2CRXF_STS));
+		return (bus->data->rxf_sts_rx_bytes &
+			ioread8(bus->reg + NPCM_I2CRXF_STS));
 	return 0;
 }
 
@@ -755,13 +775,13 @@ static void npcm_i2c_write_to_fifo_master(struct npcm_i2c *bus, u16 max_bytes)
 	 * Fill the FIFO, while the FIFO is not full and there are more bytes
 	 * to write
 	 */
-	size_free_fifo = I2C_HW_FIFO_SIZE - npcm_i2c_fifo_usage(bus);
+	size_free_fifo = bus->data->fifo_size - npcm_i2c_fifo_usage(bus);
 	while (max_bytes-- && size_free_fifo) {
 		if (bus->wr_ind < bus->wr_size)
 			npcm_i2c_wr_byte(bus, bus->wr_buf[bus->wr_ind++]);
 		else
 			npcm_i2c_wr_byte(bus, 0xFF);
-		size_free_fifo = I2C_HW_FIFO_SIZE - npcm_i2c_fifo_usage(bus);
+		size_free_fifo = bus->data->fifo_size - npcm_i2c_fifo_usage(bus);
 	}
 }
 
@@ -782,11 +802,11 @@ static void npcm_i2c_set_fifo(struct npcm_i2c *bus, int nread, int nwrite)
 
 	/* configure RX FIFO */
 	if (nread > 0) {
-		rxf_ctl = min_t(int, nread, I2C_HW_FIFO_SIZE);
+		rxf_ctl = min_t(int, nread, bus->data->fifo_size);
 
 		/* set LAST bit. if LAST is set next FIFO packet is nacked */
-		if (nread <= I2C_HW_FIFO_SIZE)
-			rxf_ctl |= NPCM_I2CRXF_CTL_LAST_PEC;
+		if (nread <= bus->data->fifo_size)
+			rxf_ctl |= bus->data->rxf_ctl_last_pec;
 
 		/*
 		 * if we are about to read the first byte in blk rd mode,
@@ -804,9 +824,9 @@ static void npcm_i2c_set_fifo(struct npcm_i2c *bus, int nread, int nwrite)
 
 	/* configure TX FIFO */
 	if (nwrite > 0) {
-		if (nwrite > I2C_HW_FIFO_SIZE)
+		if (nwrite > bus->data->fifo_size)
 			/* data to send is more then FIFO size. */
-			iowrite8(I2C_HW_FIFO_SIZE, bus->reg + NPCM_I2CTXF_CTL);
+			iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CTXF_CTL);
 		else
 			iowrite8(nwrite, bus->reg + NPCM_I2CTXF_CTL);
 
@@ -873,13 +893,13 @@ static void npcm_i2c_write_fifo_slave(struct npcm_i2c *bus, u16 max_bytes)
 	npcm_i2c_clear_fifo_int(bus);
 	npcm_i2c_clear_tx_fifo(bus);
 	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
-	while (max_bytes-- && I2C_HW_FIFO_SIZE != npcm_i2c_fifo_usage(bus)) {
+	while (max_bytes-- && bus->data->fifo_size != npcm_i2c_fifo_usage(bus)) {
 		if (bus->slv_wr_size <= 0)
 			break;
-		bus->slv_wr_ind = bus->slv_wr_ind % I2C_HW_FIFO_SIZE;
+		bus->slv_wr_ind = bus->slv_wr_ind & (bus->data->fifo_size - 1);
 		npcm_i2c_wr_byte(bus, bus->slv_wr_buf[bus->slv_wr_ind]);
 		bus->slv_wr_ind++;
-		bus->slv_wr_ind = bus->slv_wr_ind % I2C_HW_FIFO_SIZE;
+		bus->slv_wr_ind = bus->slv_wr_ind & (bus->data->fifo_size - 1);
 		bus->slv_wr_size--;
 	}
 }
@@ -894,7 +914,7 @@ static void npcm_i2c_read_fifo_slave(struct npcm_i2c *bus, u8 bytes_in_fifo)
 	while (bytes_in_fifo--) {
 		data = npcm_i2c_rd_byte(bus);
 
-		bus->slv_rd_ind = bus->slv_rd_ind % I2C_HW_FIFO_SIZE;
+		bus->slv_rd_ind = bus->slv_rd_ind & (bus->data->fifo_size - 1);
 		bus->slv_rd_buf[bus->slv_rd_ind] = data;
 		bus->slv_rd_ind++;
 
@@ -912,8 +932,8 @@ static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
 	int ret = bus->slv_wr_ind;
 
 	/* fill a cyclic buffer */
-	for (i = 0; i < I2C_HW_FIFO_SIZE; i++) {
-		if (bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
+	for (i = 0; i < bus->data->fifo_size; i++) {
+		if (bus->slv_wr_size >= bus->data->fifo_size)
 			break;
 		if (bus->state == I2C_SLAVE_MATCH) {
 			i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
@@ -921,11 +941,11 @@ static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
 		} else {
 			i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
 		}
-		ind = (bus->slv_wr_ind + bus->slv_wr_size) % I2C_HW_FIFO_SIZE;
+		ind = (bus->slv_wr_ind + bus->slv_wr_size) & (bus->data->fifo_size - 1);
 		bus->slv_wr_buf[ind] = value;
 		bus->slv_wr_size++;
 	}
-	return I2C_HW_FIFO_SIZE - ret;
+	return bus->data->fifo_size - ret;
 }
 
 static void npcm_i2c_slave_send_rd_buf(struct npcm_i2c *bus)
@@ -960,7 +980,7 @@ static void npcm_i2c_slave_receive(struct npcm_i2c *bus, u16 nread,
 	bus->slv_rd_ind = 0;
 
 	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
-	iowrite8(I2C_HW_FIFO_SIZE, bus->reg + NPCM_I2CRXF_CTL);
+	iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CRXF_CTL);
 	npcm_i2c_clear_tx_fifo(bus);
 	npcm_i2c_clear_rx_fifo(bus);
 }
@@ -993,12 +1013,12 @@ static void npcm_i2c_slave_wr_buf_sync(struct npcm_i2c *bus)
 {
 	int left_in_fifo;
 
-	left_in_fifo = FIELD_GET(NPCM_I2CTXF_STS_TX_BYTES,
-				 ioread8(bus->reg + NPCM_I2CTXF_STS));
+	left_in_fifo = bus->data->txf_sts_tx_bytes &
+			ioread8(bus->reg + NPCM_I2CTXF_STS);
 
 	/* fifo already full: */
-	if (left_in_fifo >= I2C_HW_FIFO_SIZE ||
-	    bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
+	if (left_in_fifo >= bus->data->fifo_size ||
+	    bus->slv_wr_size >= bus->data->fifo_size)
 		return;
 
 	/* update the wr fifo index back to the untransmitted bytes: */
@@ -1006,7 +1026,7 @@ static void npcm_i2c_slave_wr_buf_sync(struct npcm_i2c *bus)
 	bus->slv_wr_size = bus->slv_wr_size + left_in_fifo;
 
 	if (bus->slv_wr_ind < 0)
-		bus->slv_wr_ind += I2C_HW_FIFO_SIZE;
+		bus->slv_wr_ind += bus->data->fifo_size;
 }
 
 static void npcm_i2c_slave_rd_wr(struct npcm_i2c *bus)
@@ -1152,7 +1172,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
 		npcm_i2c_clear_rx_fifo(bus);
 		npcm_i2c_clear_tx_fifo(bus);
 		iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
-		iowrite8(I2C_HW_FIFO_SIZE, bus->reg + NPCM_I2CRXF_CTL);
+		iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CRXF_CTL);
 		if (NPCM_I2CST_XMIT & i2cst) {
 			bus->operation = I2C_WRITE_OPER;
 		} else {
@@ -1313,8 +1333,8 @@ static void npcm_i2c_master_fifo_read(struct npcm_i2c *bus)
 	 * read == FIFO Size + C (where C < FIFO Size)then first read C bytes
 	 * and in the next int we read rest of the data.
 	 */
-	if (rcount < (2 * I2C_HW_FIFO_SIZE) && rcount > I2C_HW_FIFO_SIZE)
-		fifo_bytes = rcount - I2C_HW_FIFO_SIZE;
+	if (rcount < (2 * bus->data->fifo_size) && rcount > bus->data->fifo_size)
+		fifo_bytes = rcount - bus->data->fifo_size;
 
 	if (rcount <= fifo_bytes) {
 		/* last bytes are about to be read - end of tx */
@@ -2193,7 +2213,7 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 	 * It cannot be cleared without resetting the module.
 	 */
 	else if (bus->cmd_err &&
-		 (NPCM_I2CRXF_CTL_LAST_PEC & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
+		 (bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
 		npcm_i2c_reset(bus);
 
 	/* after any xfer, successful or not, stall and EOB must be disabled */
@@ -2262,6 +2282,7 @@ static int npcm_i2c_probe_bus(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
 	static struct regmap *gcr_regmap;
+	struct device *dev = &pdev->dev;
 	struct i2c_adapter *adap;
 	struct npcm_i2c *bus;
 	struct clk *i2c_clk;
@@ -2274,6 +2295,12 @@ static int npcm_i2c_probe_bus(struct platform_device *pdev)
 
 	bus->dev = &pdev->dev;
 
+	bus->data = of_device_get_match_data(dev);
+	if (!bus->data) {
+		dev_err(dev, "OF data missing\n");
+		return -EINVAL;
+	}
+
 	bus->num = of_alias_get_id(pdev->dev.of_node, "i2c");
 	/* core clk must be acquired to calculate module timing settings */
 	i2c_clk = devm_clk_get(&pdev->dev, NULL);
@@ -2287,7 +2314,7 @@ static int npcm_i2c_probe_bus(struct platform_device *pdev)
 
 	if (IS_ERR(gcr_regmap))
 		return PTR_ERR(gcr_regmap);
-	regmap_write(gcr_regmap, NPCM_I2CSEGCTL, NPCM_I2CSEGCTL_INIT_VAL);
+	regmap_write(gcr_regmap, NPCM_I2CSEGCTL, bus->data->segctl_init_val);
 
 	bus->reg = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(bus->reg))
@@ -2349,7 +2376,8 @@ static int npcm_i2c_remove_bus(struct platform_device *pdev)
 }
 
 static const struct of_device_id npcm_i2c_bus_of_table[] = {
-	{ .compatible = "nuvoton,npcm750-i2c", },
+	{ .compatible = "nuvoton,npcm750-i2c", .data = &npxm7xx_i2c_data },
+	{ .compatible = "nuvoton,npcm845-i2c", .data = &npxm8xx_i2c_data },
 	{}
 };
 MODULE_DEVICE_TABLE(of, npcm_i2c_bus_of_table);
-- 
2.17.1

[PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

Make the one-line comments capital in the driver to get the comment style
consistent.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index 86fd942ea648..7d863edc14e4 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -680,7 +680,7 @@ static void npcm_i2c_reset(struct npcm_i2c *bus)
 	}
 #endif
 
-	/* clear status bits for spurious interrupts */
+	/* Clear status bits for spurious interrupts */
 	npcm_i2c_clear_master_status(bus);
 
 	bus->state = I2C_IDLE;
@@ -1252,7 +1252,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
 	} /* SDAST */
 
 	/*
-	 * if irq is not one of the above, make sure EOB is disabled and all
+	 * If irq is not one of the above, make sure EOB is disabled and all
 	 * status bits are cleared.
 	 */
 	if (ret == IRQ_NONE) {
@@ -1506,7 +1506,7 @@ static void npcm_i2c_irq_handle_nack(struct npcm_i2c *bus)
 		npcm_i2c_clear_master_status(bus);
 		readx_poll_timeout_atomic(ioread8, bus->reg + NPCM_I2CCST, val,
 					  !(val & NPCM_I2CCST_BUSY), 10, 200);
-		/* verify no status bits are still set after bus is released */
+		/* Verify no status bits are still set after bus is released */
 		npcm_i2c_clear_master_status(bus);
 	}
 	bus->state = I2C_IDLE;
@@ -1974,7 +1974,7 @@ static int npcm_i2c_init_module(struct npcm_i2c *bus, enum i2c_mode mode,
 
 	npcm_i2c_reset(bus);
 
-	/* check HW is OK: SDA and SCL should be high at this point. */
+	/* Check HW is OK: SDA and SCL should be high at this point. */
 	if ((npcm_i2c_get_SDA(&bus->adap) == 0) || (npcm_i2c_get_SCL(&bus->adap) == 0)) {
 		dev_err(bus->dev, "I2C%d init fail: lines are low\n", bus->num);
 		dev_err(bus->dev, "SDA=%d SCL=%d\n", npcm_i2c_get_SDA(&bus->adap),
@@ -2034,7 +2034,7 @@ static irqreturn_t npcm_i2c_bus_irq(int irq, void *dev_id)
 			return IRQ_HANDLED;
 	}
 #endif
-	/* clear status bits for spurious interrupts */
+	/* Clear status bits for spurious interrupts */
 	npcm_i2c_clear_master_status(bus);
 
 	return IRQ_HANDLED;
@@ -2216,7 +2216,7 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 		 (bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
 		npcm_i2c_reset(bus);
 
-	/* after any xfer, successful or not, stall and EOB must be disabled */
+	/* After any xfer, successful or not, stall and EOB must be disabled */
 	npcm_i2c_stall_after_start(bus, false);
 	npcm_i2c_eob_int(bus, false);
 
-- 
2.17.1

[PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

[Tyrone Ting]

From: Tyrone Ting <kfting@nuvoton.com>

Make the one-line comments capital in the driver to get the comment style
consistent.

Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
---
 drivers/i2c/busses/i2c-npcm7xx.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-npcm7xx.c b/drivers/i2c/busses/i2c-npcm7xx.c
index 86fd942ea648..7d863edc14e4 100644
--- a/drivers/i2c/busses/i2c-npcm7xx.c
+++ b/drivers/i2c/busses/i2c-npcm7xx.c
@@ -680,7 +680,7 @@ static void npcm_i2c_reset(struct npcm_i2c *bus)
 	}
 #endif
 
-	/* clear status bits for spurious interrupts */
+	/* Clear status bits for spurious interrupts */
 	npcm_i2c_clear_master_status(bus);
 
 	bus->state = I2C_IDLE;
@@ -1252,7 +1252,7 @@ static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
 	} /* SDAST */
 
 	/*
-	 * if irq is not one of the above, make sure EOB is disabled and all
+	 * If irq is not one of the above, make sure EOB is disabled and all
 	 * status bits are cleared.
 	 */
 	if (ret == IRQ_NONE) {
@@ -1506,7 +1506,7 @@ static void npcm_i2c_irq_handle_nack(struct npcm_i2c *bus)
 		npcm_i2c_clear_master_status(bus);
 		readx_poll_timeout_atomic(ioread8, bus->reg + NPCM_I2CCST, val,
 					  !(val & NPCM_I2CCST_BUSY), 10, 200);
-		/* verify no status bits are still set after bus is released */
+		/* Verify no status bits are still set after bus is released */
 		npcm_i2c_clear_master_status(bus);
 	}
 	bus->state = I2C_IDLE;
@@ -1974,7 +1974,7 @@ static int npcm_i2c_init_module(struct npcm_i2c *bus, enum i2c_mode mode,
 
 	npcm_i2c_reset(bus);
 
-	/* check HW is OK: SDA and SCL should be high at this point. */
+	/* Check HW is OK: SDA and SCL should be high at this point. */
 	if ((npcm_i2c_get_SDA(&bus->adap) == 0) || (npcm_i2c_get_SCL(&bus->adap) == 0)) {
 		dev_err(bus->dev, "I2C%d init fail: lines are low\n", bus->num);
 		dev_err(bus->dev, "SDA=%d SCL=%d\n", npcm_i2c_get_SDA(&bus->adap),
@@ -2034,7 +2034,7 @@ static irqreturn_t npcm_i2c_bus_irq(int irq, void *dev_id)
 			return IRQ_HANDLED;
 	}
 #endif
-	/* clear status bits for spurious interrupts */
+	/* Clear status bits for spurious interrupts */
 	npcm_i2c_clear_master_status(bus);
 
 	return IRQ_HANDLED;
@@ -2216,7 +2216,7 @@ static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 		 (bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
 		npcm_i2c_reset(bus);
 
-	/* after any xfer, successful or not, stall and EOB must be disabled */
+	/* After any xfer, successful or not, stall and EOB must be disabled */
 	npcm_i2c_stall_after_start(bus, false);
 	npcm_i2c_eob_int(bus, false);
 
-- 
2.17.1

Re: [PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[Andy Shevchenko]

On Wed, May 25, 2022 at 11:23:36AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> This patchset includes the following fixes:
> 
> - Add dt-bindings description for NPCM845.
> - Bug fix for timeout calculation.
> - Better handling of spurious interrupts.
> - Fix for event type in slave mode.
> - Removal of own slave addresses [2:10].
> - Support for next gen BMC (NPCM845).
> 
> The NPCM I2C driver is tested on NPCM750 and NPCM845 evaluation boards.

LGTM,
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

> Addressed comments from:
>  - Wolfram Sang : https://lkml.org/lkml/2022/5/21/51
> 
> Changes since version 5:
>  - Shorten npcm_i2caddr array since the number of supported i2c slave
>    addresses is reduced.
>  - Create a new patch from the original PATCH v5 08/10 to modify the slave
>    transaction logic.
> 
> Changes since version 4:
>  - Remove quotes around ref handle to nuvoton,sys-mgr in i2c binding
>    document.
>  - Keep the "longer line first" order.
>  - Correct the SoB chain.
>  - Modify the if statement in one line and add new line characters.
>  - Modify the commit message format in the patch Remove own slave
>    addresses 2:10. Correct the if statement in one line and shorten the
>    debug messages.
>  - Create a new patch to capitalize the one-line comment in the driver.
> 
> Changes since version 3:
>  - Correct the const format in if condition in i2c binding document.
>  - Add the oops message statement and register information in register
>    access width patch.
>  - Add the occurring rate of the i2c spurious interrupt issue and more
>    details in driver's behavior to overcome this issue.
>  - Address Andy's comments in the patch to support NPCM845.
>  
> Changes since version 2:
>  - Keep old code as fallback, if getting nuvoton,sys-mgr property fails.
>  - Fix the error reported by running 'make DT_CHECKER_FLAGS=-m 
>    dt_binding_check'.
>  - Make nuvoton,sys-mgr required for nuvoton,npcm845-i2c.
>  - Correct the patch's subject about changing the way of getting GCR
>    regmap and add the description about keeping old code as fallback
>    if getting nuvoton,sys-mgr property fails.
>  - Correct the patch title and description about removing the unused 
>    variable clk_regmap.
>  - Use the data field directly instead of the macros since macros are
>    not constants anymore in this patch.
>  
> Changes since version 1:
>  - Add nuvoton,sys-mgr property in NPCM devicetree.
>  - Describe the commit message in imperative mood.
>  - Modify the description in i2c binding document to cover NPCM series.
>  - Add new property in i2c binding document.
>  - Create a new patch for client address calculation.
>  - Create a new patch for updating gcr property name.
>  - Create a new patch for removing unused clock node.
>  - Explain EOB in the commit description.
>  - Create a new patch for correcting NPCM register access width.
>  - Remove some comment since the corresponding logic no longer exists.
>  - Remove fixes tag while the patch adds an additional feature.
>  - Use devicetree data field to support NPCM845.
> 
> Tali Perry (2):
>   i2c: npcm: Remove own slave addresses 2:10
>   i2c: npcm: Correct slave role behavior
> 
> Tyrone Ting (3):
>   dt-bindings: i2c: npcm: support NPCM845
>   i2c: npcm: Support NPCM845
>   i2c: npcm: Capitalize the one-line comment
> 
>  .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     |  25 ++-
>  drivers/i2c/busses/Kconfig                    |   8 +-
>  drivers/i2c/busses/Makefile                   |   2 +-
>  drivers/i2c/busses/i2c-npcm7xx.c              | 176 ++++++++++--------
>  4 files changed, 124 insertions(+), 87 deletions(-)
> 
> -- 
> 2.17.1
> 

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[Andy Shevchenko]

On Wed, May 25, 2022 at 11:23:36AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> This patchset includes the following fixes:
> 
> - Add dt-bindings description for NPCM845.
> - Bug fix for timeout calculation.
> - Better handling of spurious interrupts.
> - Fix for event type in slave mode.
> - Removal of own slave addresses [2:10].
> - Support for next gen BMC (NPCM845).
> 
> The NPCM I2C driver is tested on NPCM750 and NPCM845 evaluation boards.

LGTM,
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

> Addressed comments from:
>  - Wolfram Sang : https://lkml.org/lkml/2022/5/21/51
> 
> Changes since version 5:
>  - Shorten npcm_i2caddr array since the number of supported i2c slave
>    addresses is reduced.
>  - Create a new patch from the original PATCH v5 08/10 to modify the slave
>    transaction logic.
> 
> Changes since version 4:
>  - Remove quotes around ref handle to nuvoton,sys-mgr in i2c binding
>    document.
>  - Keep the "longer line first" order.
>  - Correct the SoB chain.
>  - Modify the if statement in one line and add new line characters.
>  - Modify the commit message format in the patch Remove own slave
>    addresses 2:10. Correct the if statement in one line and shorten the
>    debug messages.
>  - Create a new patch to capitalize the one-line comment in the driver.
> 
> Changes since version 3:
>  - Correct the const format in if condition in i2c binding document.
>  - Add the oops message statement and register information in register
>    access width patch.
>  - Add the occurring rate of the i2c spurious interrupt issue and more
>    details in driver's behavior to overcome this issue.
>  - Address Andy's comments in the patch to support NPCM845.
>  
> Changes since version 2:
>  - Keep old code as fallback, if getting nuvoton,sys-mgr property fails.
>  - Fix the error reported by running 'make DT_CHECKER_FLAGS=-m 
>    dt_binding_check'.
>  - Make nuvoton,sys-mgr required for nuvoton,npcm845-i2c.
>  - Correct the patch's subject about changing the way of getting GCR
>    regmap and add the description about keeping old code as fallback
>    if getting nuvoton,sys-mgr property fails.
>  - Correct the patch title and description about removing the unused 
>    variable clk_regmap.
>  - Use the data field directly instead of the macros since macros are
>    not constants anymore in this patch.
>  
> Changes since version 1:
>  - Add nuvoton,sys-mgr property in NPCM devicetree.
>  - Describe the commit message in imperative mood.
>  - Modify the description in i2c binding document to cover NPCM series.
>  - Add new property in i2c binding document.
>  - Create a new patch for client address calculation.
>  - Create a new patch for updating gcr property name.
>  - Create a new patch for removing unused clock node.
>  - Explain EOB in the commit description.
>  - Create a new patch for correcting NPCM register access width.
>  - Remove some comment since the corresponding logic no longer exists.
>  - Remove fixes tag while the patch adds an additional feature.
>  - Use devicetree data field to support NPCM845.
> 
> Tali Perry (2):
>   i2c: npcm: Remove own slave addresses 2:10
>   i2c: npcm: Correct slave role behavior
> 
> Tyrone Ting (3):
>   dt-bindings: i2c: npcm: support NPCM845
>   i2c: npcm: Support NPCM845
>   i2c: npcm: Capitalize the one-line comment
> 
>  .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     |  25 ++-
>  drivers/i2c/busses/Kconfig                    |   8 +-
>  drivers/i2c/busses/Makefile                   |   2 +-
>  drivers/i2c/busses/i2c-npcm7xx.c              | 176 ++++++++++--------
>  4 files changed, 124 insertions(+), 87 deletions(-)
> 
> -- 
> 2.17.1
> 

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[Tyrone Ting]

Hi Andy:

Thank you for your review.

Much appreciated.

Andy Shevchenko <andriy.shevchenko@linux.intel.com> 於 2022年5月26日 週四 上午1:32寫道：
>
> On Wed, May 25, 2022 at 11:23:36AM +0800, Tyrone Ting wrote:
> > From: Tyrone Ting <kfting@nuvoton.com>
> >
> > This patchset includes the following fixes:
> >
> > - Add dt-bindings description for NPCM845.
> > - Bug fix for timeout calculation.
> > - Better handling of spurious interrupts.
> > - Fix for event type in slave mode.
> > - Removal of own slave addresses [2:10].
> > - Support for next gen BMC (NPCM845).
> >
> > The NPCM I2C driver is tested on NPCM750 and NPCM845 evaluation boards.
>
> LGTM,
> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
>
> > Addressed comments from:
> >  - Wolfram Sang : https://lkml.org/lkml/2022/5/21/51
> >
> > Changes since version 5:
> >  - Shorten npcm_i2caddr array since the number of supported i2c slave
> >    addresses is reduced.
> >  - Create a new patch from the original PATCH v5 08/10 to modify the slave
> >    transaction logic.
> >
> > Changes since version 4:
> >  - Remove quotes around ref handle to nuvoton,sys-mgr in i2c binding
> >    document.
> >  - Keep the "longer line first" order.
> >  - Correct the SoB chain.
> >  - Modify the if statement in one line and add new line characters.
> >  - Modify the commit message format in the patch Remove own slave
> >    addresses 2:10. Correct the if statement in one line and shorten the
> >    debug messages.
> >  - Create a new patch to capitalize the one-line comment in the driver.
> >
> > Changes since version 3:
> >  - Correct the const format in if condition in i2c binding document.
> >  - Add the oops message statement and register information in register
> >    access width patch.
> >  - Add the occurring rate of the i2c spurious interrupt issue and more
> >    details in driver's behavior to overcome this issue.
> >  - Address Andy's comments in the patch to support NPCM845.
> >
> > Changes since version 2:
> >  - Keep old code as fallback, if getting nuvoton,sys-mgr property fails.
> >  - Fix the error reported by running 'make DT_CHECKER_FLAGS=-m
> >    dt_binding_check'.
> >  - Make nuvoton,sys-mgr required for nuvoton,npcm845-i2c.
> >  - Correct the patch's subject about changing the way of getting GCR
> >    regmap and add the description about keeping old code as fallback
> >    if getting nuvoton,sys-mgr property fails.
> >  - Correct the patch title and description about removing the unused
> >    variable clk_regmap.
> >  - Use the data field directly instead of the macros since macros are
> >    not constants anymore in this patch.
> >
> > Changes since version 1:
> >  - Add nuvoton,sys-mgr property in NPCM devicetree.
> >  - Describe the commit message in imperative mood.
> >  - Modify the description in i2c binding document to cover NPCM series.
> >  - Add new property in i2c binding document.
> >  - Create a new patch for client address calculation.
> >  - Create a new patch for updating gcr property name.
> >  - Create a new patch for removing unused clock node.
> >  - Explain EOB in the commit description.
> >  - Create a new patch for correcting NPCM register access width.
> >  - Remove some comment since the corresponding logic no longer exists.
> >  - Remove fixes tag while the patch adds an additional feature.
> >  - Use devicetree data field to support NPCM845.
> >
> > Tali Perry (2):
> >   i2c: npcm: Remove own slave addresses 2:10
> >   i2c: npcm: Correct slave role behavior
> >
> > Tyrone Ting (3):
> >   dt-bindings: i2c: npcm: support NPCM845
> >   i2c: npcm: Support NPCM845
> >   i2c: npcm: Capitalize the one-line comment
> >
> >  .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     |  25 ++-
> >  drivers/i2c/busses/Kconfig                    |   8 +-
> >  drivers/i2c/busses/Makefile                   |   2 +-
> >  drivers/i2c/busses/i2c-npcm7xx.c              | 176 ++++++++++--------
> >  4 files changed, 124 insertions(+), 87 deletions(-)
> >
> > --
> > 2.17.1
> >
>
> --
> With Best Regards,
> Andy Shevchenko
>
>

Best Regards,
Tyrone

Re: [PATCH v6 0/5] i2c: npcm: Bug fixes timeout, spurious interrupts

[Tyrone Ting]

Hi Andy:

Thank you for your review.

Much appreciated.

Andy Shevchenko <andriy.shevchenko@linux.intel.com> 於 2022年5月26日 週四 上午1:32寫道：
>
> On Wed, May 25, 2022 at 11:23:36AM +0800, Tyrone Ting wrote:
> > From: Tyrone Ting <kfting@nuvoton.com>
> >
> > This patchset includes the following fixes:
> >
> > - Add dt-bindings description for NPCM845.
> > - Bug fix for timeout calculation.
> > - Better handling of spurious interrupts.
> > - Fix for event type in slave mode.
> > - Removal of own slave addresses [2:10].
> > - Support for next gen BMC (NPCM845).
> >
> > The NPCM I2C driver is tested on NPCM750 and NPCM845 evaluation boards.
>
> LGTM,
> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
>
> > Addressed comments from:
> >  - Wolfram Sang : https://lkml.org/lkml/2022/5/21/51
> >
> > Changes since version 5:
> >  - Shorten npcm_i2caddr array since the number of supported i2c slave
> >    addresses is reduced.
> >  - Create a new patch from the original PATCH v5 08/10 to modify the slave
> >    transaction logic.
> >
> > Changes since version 4:
> >  - Remove quotes around ref handle to nuvoton,sys-mgr in i2c binding
> >    document.
> >  - Keep the "longer line first" order.
> >  - Correct the SoB chain.
> >  - Modify the if statement in one line and add new line characters.
> >  - Modify the commit message format in the patch Remove own slave
> >    addresses 2:10. Correct the if statement in one line and shorten the
> >    debug messages.
> >  - Create a new patch to capitalize the one-line comment in the driver.
> >
> > Changes since version 3:
> >  - Correct the const format in if condition in i2c binding document.
> >  - Add the oops message statement and register information in register
> >    access width patch.
> >  - Add the occurring rate of the i2c spurious interrupt issue and more
> >    details in driver's behavior to overcome this issue.
> >  - Address Andy's comments in the patch to support NPCM845.
> >
> > Changes since version 2:
> >  - Keep old code as fallback, if getting nuvoton,sys-mgr property fails.
> >  - Fix the error reported by running 'make DT_CHECKER_FLAGS=-m
> >    dt_binding_check'.
> >  - Make nuvoton,sys-mgr required for nuvoton,npcm845-i2c.
> >  - Correct the patch's subject about changing the way of getting GCR
> >    regmap and add the description about keeping old code as fallback
> >    if getting nuvoton,sys-mgr property fails.
> >  - Correct the patch title and description about removing the unused
> >    variable clk_regmap.
> >  - Use the data field directly instead of the macros since macros are
> >    not constants anymore in this patch.
> >
> > Changes since version 1:
> >  - Add nuvoton,sys-mgr property in NPCM devicetree.
> >  - Describe the commit message in imperative mood.
> >  - Modify the description in i2c binding document to cover NPCM series.
> >  - Add new property in i2c binding document.
> >  - Create a new patch for client address calculation.
> >  - Create a new patch for updating gcr property name.
> >  - Create a new patch for removing unused clock node.
> >  - Explain EOB in the commit description.
> >  - Create a new patch for correcting NPCM register access width.
> >  - Remove some comment since the corresponding logic no longer exists.
> >  - Remove fixes tag while the patch adds an additional feature.
> >  - Use devicetree data field to support NPCM845.
> >
> > Tali Perry (2):
> >   i2c: npcm: Remove own slave addresses 2:10
> >   i2c: npcm: Correct slave role behavior
> >
> > Tyrone Ting (3):
> >   dt-bindings: i2c: npcm: support NPCM845
> >   i2c: npcm: Support NPCM845
> >   i2c: npcm: Capitalize the one-line comment
> >
> >  .../bindings/i2c/nuvoton,npcm7xx-i2c.yaml     |  25 ++-
> >  drivers/i2c/busses/Kconfig                    |   8 +-
> >  drivers/i2c/busses/Makefile                   |   2 +-
> >  drivers/i2c/busses/i2c-npcm7xx.c              | 176 ++++++++++--------
> >  4 files changed, 124 insertions(+), 87 deletions(-)
> >
> > --
> > 2.17.1
> >
>
> --
> With Best Regards,
> Andy Shevchenko
>
>

Best Regards,
Tyrone

Re: [PATCH v6 1/5] dt-bindings: i2c: npcm: support NPCM845

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 383 bytes --]

On Wed, May 25, 2022 at 11:23:37AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> Add compatible and nuvoton,sys-mgr description for NPCM i2c module.
> 
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Rob Herring <robh@kernel.org>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 1/5] dt-bindings: i2c: npcm: support NPCM845

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 383 bytes --]

On Wed, May 25, 2022 at 11:23:37AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> Add compatible and nuvoton,sys-mgr description for NPCM i2c module.
> 
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Rob Herring <robh@kernel.org>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 2/5] i2c: npcm: Remove own slave addresses 2:10

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 817 bytes --]

On Wed, May 25, 2022 at 11:23:38AM +0800, Tyrone Ting wrote:
> From: Tali Perry <tali.perry1@gmail.com>
> 
> NPCM can support up to 10 own slave addresses. In practice, only one
> address is actually being used. In order to access addresses 2 and above,
> need to switch register banks. The switch needs spinlock.
> To avoid using spinlock for this useless feature removed support of SA >=
> 2. Also fix returned slave event enum.
> 
> Remove some comment since the bank selection is not required. The bank
> selection is not required since the supported slave addresses are reduced.
> 
> Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> Signed-off-by: Tali Perry <tali.perry1@gmail.com>
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 2/5] i2c: npcm: Remove own slave addresses 2:10

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 817 bytes --]

On Wed, May 25, 2022 at 11:23:38AM +0800, Tyrone Ting wrote:
> From: Tali Perry <tali.perry1@gmail.com>
> 
> NPCM can support up to 10 own slave addresses. In practice, only one
> address is actually being used. In order to access addresses 2 and above,
> need to switch register banks. The switch needs spinlock.
> To avoid using spinlock for this useless feature removed support of SA >=
> 2. Also fix returned slave event enum.
> 
> Remove some comment since the bank selection is not required. The bank
> selection is not required since the supported slave addresses are reduced.
> 
> Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> Signed-off-by: Tali Perry <tali.perry1@gmail.com>
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 3/5] i2c: npcm: Correct slave role behavior

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 465 bytes --]

On Wed, May 25, 2022 at 11:23:39AM +0800, Tyrone Ting wrote:
> From: Tali Perry <tali.perry1@gmail.com>
> 
> Correct the slave transaction logic to be compatible with the generic
> slave backend driver.
> 
> Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> Signed-off-by: Tali Perry <tali.perry1@gmail.com>
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>

Much easier to review this way! Applied to for-next, thank you!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 3/5] i2c: npcm: Correct slave role behavior

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 465 bytes --]

On Wed, May 25, 2022 at 11:23:39AM +0800, Tyrone Ting wrote:
> From: Tali Perry <tali.perry1@gmail.com>
> 
> Correct the slave transaction logic to be compatible with the generic
> slave backend driver.
> 
> Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> Signed-off-by: Tali Perry <tali.perry1@gmail.com>
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>

Much easier to review this way! Applied to for-next, thank you!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 4/5] i2c: npcm: Support NPCM845

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 372 bytes --]

On Wed, May 25, 2022 at 11:23:40AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> Add NPCM8XX I2C support.
> The NPCM8XX uses a similar i2c module as NPCM7XX.
> The internal HW FIFO is larger in NPCM8XX.
> 
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
> Acked-by: Tomer Maimon <tmaimon77@gmail.com>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 4/5] i2c: npcm: Support NPCM845

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 372 bytes --]

On Wed, May 25, 2022 at 11:23:40AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> Add NPCM8XX I2C support.
> The NPCM8XX uses a similar i2c module as NPCM7XX.
> The internal HW FIFO is larger in NPCM8XX.
> 
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
> Acked-by: Tomer Maimon <tmaimon77@gmail.com>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 369 bytes --]

On Wed, May 25, 2022 at 11:23:41AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> Make the one-line comments capital in the driver to get the comment style
> consistent.
> 
> Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 369 bytes --]

On Wed, May 25, 2022 at 11:23:41AM +0800, Tyrone Ting wrote:
> From: Tyrone Ting <kfting@nuvoton.com>
> 
> Make the one-line comments capital in the driver to get the comment style
> consistent.
> 
> Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> Signed-off-by: Tyrone Ting <kfting@nuvoton.com>

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v6 1/5] dt-bindings: i2c: npcm: support NPCM845

[Tyrone Ting]

Hi Wolfram:

Thank you for your review and comments.

Wolfram Sang <wsa@kernel.org> 於 2022年6月9日 週四 上午4:02寫道：
>
> On Wed, May 25, 2022 at 11:23:37AM +0800, Tyrone Ting wrote:
> > From: Tyrone Ting <kfting@nuvoton.com>
> >
> > Add compatible and nuvoton,sys-mgr description for NPCM i2c module.
> >
> > Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
> > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> > Reviewed-by: Rob Herring <robh@kernel.org>
>
> Applied to for-next, thanks!
>

Best Regards,
Tyrone

Re: [PATCH v6 2/5] i2c: npcm: Remove own slave addresses 2:10

[Tyrone Ting]

Hi Wolfram:

Thank you for your review and comments.

Wolfram Sang <wsa@kernel.org> 於 2022年6月9日 週四 上午4:02寫道：
>
> On Wed, May 25, 2022 at 11:23:38AM +0800, Tyrone Ting wrote:
> > From: Tali Perry <tali.perry1@gmail.com>
> >
> > NPCM can support up to 10 own slave addresses. In practice, only one
> > address is actually being used. In order to access addresses 2 and above,
> > need to switch register banks. The switch needs spinlock.
> > To avoid using spinlock for this useless feature removed support of SA >=
> > 2. Also fix returned slave event enum.
> >
> > Remove some comment since the bank selection is not required. The bank
> > selection is not required since the supported slave addresses are reduced.
> >
> > Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> > Signed-off-by: Tali Perry <tali.perry1@gmail.com>
> > Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
>
> Applied to for-next, thanks!
>

Best Regards,
Tyrone

Re: [PATCH v6 3/5] i2c: npcm: Correct slave role behavior

[Tyrone Ting]

Hi Wolfram:

Your previous suggestion about this commit is highly appreciated.

Thank you.

Wolfram Sang <wsa@kernel.org> 於 2022年6月9日 週四 上午4:03寫道：
>
> On Wed, May 25, 2022 at 11:23:39AM +0800, Tyrone Ting wrote:
> > From: Tali Perry <tali.perry1@gmail.com>
> >
> > Correct the slave transaction logic to be compatible with the generic
> > slave backend driver.
> >
> > Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> > Signed-off-by: Tali Perry <tali.perry1@gmail.com>
> > Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
>
> Much easier to review this way! Applied to for-next, thank you!
>

Best Regards,
Tyrone

Re: [PATCH v6 4/5] i2c: npcm: Support NPCM845

[Tyrone Ting]

Hi Wolfram:

Thank you for your review and comments.

Wolfram Sang <wsa@kernel.org> 於 2022年6月9日 週四 上午4:03寫道：
>
> On Wed, May 25, 2022 at 11:23:40AM +0800, Tyrone Ting wrote:
> > From: Tyrone Ting <kfting@nuvoton.com>
> >
> > Add NPCM8XX I2C support.
> > The NPCM8XX uses a similar i2c module as NPCM7XX.
> > The internal HW FIFO is larger in NPCM8XX.
> >
> > Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
> > Acked-by: Tomer Maimon <tmaimon77@gmail.com>
>
> Applied to for-next, thanks!
>

Best Regards,
Tyrone

Re: [PATCH v6 5/5] i2c: npcm: Capitalize the one-line comment

[Tyrone Ting]

Hi Wolfram:

Thank you for your review and comments for this whole patch set.

Wolfram Sang <wsa@kernel.org> 於 2022年6月9日 週四 上午4:04寫道：
>
> On Wed, May 25, 2022 at 11:23:41AM +0800, Tyrone Ting wrote:
> > From: Tyrone Ting <kfting@nuvoton.com>
> >
> > Make the one-line comments capital in the driver to get the comment style
> > consistent.
> >
> > Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
> > Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
>
> Applied to for-next, thanks!
>

Best Regards,
Tyrone