[PATCH 1/6] ARM: dts: stm32: Add alternate pinmux for UART3 pins

[PATCH 1/6] ARM: dts: stm32: Add alternate pinmux for UART3 pins

[Marek Vasut]

Add another mux option for UART3 pins, this is used on DRC Compact board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
 arch/arm/dts/stm32mp15-pinctrl.dtsi | 41 +++++++++++++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
index f0d66d8c6e3..823ef2e2aab 100644
--- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
@@ -2134,6 +2134,47 @@
 		};
 	};
 
+	usart3_pins_e: usart3-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart3_idle_pins_e: usart3-idle-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart3_sleep_pins_e: usart3-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 11, ANALOG)>; /* USART3_RX */
+		};
+	};
+
 	usbotg_hs_pins_a: usbotg-hs-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
-- 
2.35.1

[PATCH 2/6] ARM: dts: stm32: Add alternate pinmux for UART4 pins

[Marek Vasut]

Add another mux option for UART4 pins, this is used on DRC Compact board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
 arch/arm/dts/stm32mp15-pinctrl.dtsi | 30 +++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
index 823ef2e2aab..dc329bf531e 100644
--- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
@@ -1835,6 +1835,36 @@
 		};
 	};
 
+	uart4_pins_d: uart4-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_idle_pins_d: uart4-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_sleep_pins_d: uart4-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+		};
+	};
+
 	uart7_pins_a: uart7-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
-- 
2.35.1

[PATCH 3/6] ARM: dts: stm32: Add alternate pinmux for UART5 pins

[Marek Vasut]

Add another mux option for UART5 pins, this is used on DRC Compact board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
 arch/arm/dts/stm32mp15-pinctrl.dtsi | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
index dc329bf531e..6a5b4016f66 100644
--- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
@@ -1865,6 +1865,19 @@
 		};
 	};
 
+	uart5_pins_a: uart5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 5, AF12)>; /* UART5_RX */
+			bias-disable;
+		};
+	};
+
 	uart7_pins_a: uart7-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
-- 
2.35.1

[PATCH 4/6] ARM: dts: stm32: Add alternate pinmux for CAN1 pins

[Marek Vasut]

Add another mux option for CAN1 pins, this is used on DRC Compact board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
 arch/arm/dts/stm32mp15-pinctrl.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
index 6a5b4016f66..e0965c5936e 100644
--- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
@@ -929,6 +929,26 @@
 		};
 	};
 
+	m_can1_pins_c: m-can1-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	m_can1_sleep_pins_c: m_can1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('H', 14, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
 	m_can2_pins_a: m-can2-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
-- 
2.35.1

[PATCH 5/6] ARM: dts: stm32: Add alternate pinmux for SPI2 pins

[Marek Vasut]

Add another mux option for SPI2 pins, this is used on DRC Compact board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
 arch/arm/dts/stm32mp15-pinctrl.dtsi | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
index e0965c5936e..b92a149a186 100644
--- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
@@ -1778,6 +1778,21 @@
 		};
 	};
 
+	spi2_pins_b: spi2-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI1_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
 	spi4_pins_a: spi4-0 {
 		pins {
 			pinmux = <STM32_PINMUX('E', 12, AF5)>, /* SPI4_SCK */
-- 
2.35.1

[PATCH 6/6] ARM: dts: stm32: Add DHCOR based DRC Compact board

[Marek Vasut]

Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
---
 arch/arm/dts/Makefile                         |   3 +-
 .../arm/dts/stm32mp153c-dhcor-drc-compact.dts |  30 ++
 .../stm32mp15xx-dhcor-drc-compact-u-boot.dtsi | 120 +++++++
 .../arm/dts/stm32mp15xx-dhcor-drc-compact.dts |  16 +
 .../dts/stm32mp15xx-dhcor-drc-compact.dtsi    | 326 ++++++++++++++++++
 .../dh_stm32mp1/u-boot-dhcor.its              |  15 +
 configs/stm32mp15_dhcor_basic_defconfig       |   1 +
 7 files changed, 510 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0a2713c06a3..8a314210da6 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1172,7 +1172,8 @@ dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp15xx-dhcom-drc02.dtb \
 	stm32mp15xx-dhcom-pdk2.dtb \
 	stm32mp15xx-dhcom-picoitx.dtb \
-	stm32mp15xx-dhcor-avenger96.dtb
+	stm32mp15xx-dhcor-avenger96.dtb \
+	stm32mp15xx-dhcor-drc-compact.dtb
 
 dtb-$(CONFIG_SOC_K3_AM6) += \
 	k3-am654-base-board.dtb \
diff --git a/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts b/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
new file mode 100644
index 00000000000..c8b9818499e
--- /dev/null
+++ b/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * DRC Compact PCB number: 627-100 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-drc-compact.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOR DRC Compact";
+	compatible = "dh,stm32mp153c-dhcor-drc-compact",
+		     "dh,stm32mp153c-dhcor-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_c>;
+	pinctrl-1 = <&m_can1_sleep_pins_c>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
new file mode 100644
index 00000000000..407fed56167
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15xx-dhcor-u-boot.dtsi"
+
+/delete-node/ &ksz8851;
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		usb0 = &usbotg_hs;
+		ethernet1 = &ks8851;
+	};
+
+	config {
+		dh,board-coding-gpios = <&gpioh 9 0>, <&gpioh 8 0>, <&gpioh 3 0>;
+	};
+
+	/* This is actually on FMC2, but we do not have bus driver for that */
+	ks8851: ks8851mll@64000000 {
+		compatible = "micrel,ks8851-mll";
+		reg = <0x64000000 0x20000>;
+	};
+};
+
+&ethernet0 {
+	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		ethernet-phy@7 {
+			reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <1000>;
+		};
+	};
+};
+
+&pinctrl {
+	/* These should bound to FMC2 bus driver, but we do not have one */
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+	st,use-ckin;
+	st,cmd-gpios = <&gpiod 2 0>;
+	st,ck-gpios = <&gpioc 12 0>;
+	st,ckin-gpios = <&gpioe 4 0>;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_b {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_c {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc3 {	/* SDIO Wi-Fi */
+	status = "disabled";
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_d {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/delete-property/ bias-disable;
+		bias-pull-up;
+	};
+};
+
+&usbotg_hs {
+	u-boot,force-b-session-valid;
+	hnp-srp-disable;
+};
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
new file mode 100644
index 00000000000..77dd944ff53
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-drc-compact.dtsi"
+
+/ {
+	model = "DH electronics STM32MP15xx DHCOR DRC Compact";
+	compatible = "dh,stm32mp15xx-dhcor-drc-compact", "st,stm32mp1xx";
+};
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
new file mode 100644
index 00000000000..bedccf0f00a
--- /dev/null
+++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		mmc0 = &sdmmc1;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+		serial0 = &uart4;
+		serial1 = &uart8;
+		serial2 = &usart3;
+		serial3 = &uart5;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "yellow:user0";
+			gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "red:user1";
+			gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {	/* X11 ADC inputs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,adc-channels = <0 1 6>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <0 1 2>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "DRCC-VAR2", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "DRCC-GPIO0", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "DRCC-GPIO5", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "DRCC-HW2",
+			  "DRCC-GPIO4", "", "", "",
+			  "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
+			  "DRCC-VAR0", "", "", "DRCC-GPIO6";
+};
+
+&gpioi {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DRCC-GPIO2",
+			  "", "DRCC-GPIO1", "", "",
+			  "", "", "", "";
+};
+
+&i2c1 {	/* X11 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {	/* MicroSD */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc2 {	/* eMMC */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc3 {	/* SDIO Wi-Fi */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	bus-width = <4>;
+	mmc-ddr-3_3v;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi2 {	/* X11 SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_b>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	label = "UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_d>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart5 {	/* X11 UART */
+	label = "X11-UART5";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	label = "RS485-1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart3 {	/* RS485 or RS232 */
+	label = "RS485-2";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart3_pins_e>;
+	pinctrl-1 = <&usart3_sleep_pins_e>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+};
diff --git a/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its b/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its
index 0ea10a14972..de7dcb317f3 100644
--- a/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its
+++ b/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its
@@ -23,6 +23,14 @@
 			arch = "arm";
 			compression = "none";
 		};
+
+		fdt-2 {
+			description = ".dtb";
+			data = /incbin/("arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtb");
+			type = "flat_dt";
+			arch = "arm";
+			compression = "none";
+		};
 	};
 
 	configurations {
@@ -35,6 +43,13 @@
 			fdt = "fdt-1";
 		};
 
+		config-2 {
+			/* DT+SoM+board model */
+			description = "dh,stm32mp15xx-dhcor-drc-compact_somrev0_boardrev0";
+			firmware = "uboot";
+			fdt = "fdt-2";
+		};
+
 		/* Add 586-200..586-400 with fdt-2..fdt-4 here */
 	};
 };
diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
index 0c4bca15402..32aa8b5dfaf 100644
--- a/configs/stm32mp15_dhcor_basic_defconfig
+++ b/configs/stm32mp15_dhcor_basic_defconfig
@@ -109,6 +109,7 @@ CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ90X1=y
 CONFIG_DM_ETH=y
 CONFIG_DWC_ETH_QOS=y
+CONFIG_KS8851_MLL=y
 CONFIG_PHY=y
 CONFIG_SPL_PHY=y
 CONFIG_PHY_STM32_USBPHYC=y
-- 
2.35.1

Re: [PATCH 1/6] ARM: dts: stm32: Add alternate pinmux for UART3 pins

[Patrice CHOTARD]

Hi Marek

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART3 pins, this is used on DRC Compact board.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>  arch/arm/dts/stm32mp15-pinctrl.dtsi | 41 +++++++++++++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> index f0d66d8c6e3..823ef2e2aab 100644
> --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> @@ -2134,6 +2134,47 @@
>  		};
>  	};
>  
> +	usart3_pins_e: usart3-4 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
> +				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
> +			bias-disable;
> +			drive-push-pull;
> +			slew-rate = <0>;
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
> +				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
> +			bias-pull-up;
> +		};
> +	};
> +
> +	usart3_idle_pins_e: usart3-idle-4 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
> +				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
> +			bias-disable;
> +			drive-push-pull;
> +			slew-rate = <0>;
> +		};
> +		pins3 {
> +			pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */
> +			bias-pull-up;
> +		};
> +	};
> +
> +	usart3_sleep_pins_e: usart3-sleep-4 {
> +		pins {
> +			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
> +				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
> +				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
> +				 <STM32_PINMUX('B', 11, ANALOG)>; /* USART3_RX */
> +		};
> +	};
> +
>  	usbotg_hs_pins_a: usbotg-hs-0 {
>  		pins {
>  			pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

Re: [PATCH 2/6] ARM: dts: stm32: Add alternate pinmux for UART4 pins

[Patrice CHOTARD]

Hi Marek

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART4 pins, this is used on DRC Compact board.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>  arch/arm/dts/stm32mp15-pinctrl.dtsi | 30 +++++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
> 
> diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> index 823ef2e2aab..dc329bf531e 100644
> --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> @@ -1835,6 +1835,36 @@
>  		};
>  	};
>  
> +	uart4_pins_d: uart4-3 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('A', 13, AF8)>; /* UART4_TX */
> +			bias-disable;
> +			drive-push-pull;
> +			slew-rate = <0>;
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
> +			bias-disable;
> +		};
> +	};
> +
> +	uart4_idle_pins_d: uart4-idle-3 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* UART4_TX */
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
> +			bias-disable;
> +		};
> +	};
> +
> +	uart4_sleep_pins_d: uart4-sleep-3 {
> +		pins {
> +			pinmux = <STM32_PINMUX('A', 13, ANALOG)>, /* UART4_TX */
> +				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
> +		};
> +	};
> +
>  	uart7_pins_a: uart7-0 {
>  		pins1 {
>  			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

Re: [PATCH 3/6] ARM: dts: stm32: Add alternate pinmux for UART5 pins

[Patrice CHOTARD]

Hi Marek

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART5 pins, this is used on DRC Compact board.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>  arch/arm/dts/stm32mp15-pinctrl.dtsi | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> index dc329bf531e..6a5b4016f66 100644
> --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> @@ -1865,6 +1865,19 @@
>  		};
>  	};
>  
> +	uart5_pins_a: uart5-0 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
> +			bias-disable;
> +			drive-push-pull;
> +			slew-rate = <0>;
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('B', 5, AF12)>; /* UART5_RX */
> +			bias-disable;
> +		};
> +	};
> +
>  	uart7_pins_a: uart7-0 {
>  		pins1 {
>  			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */

Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

Re: [PATCH 4/6] ARM: dts: stm32: Add alternate pinmux for CAN1 pins

[Patrice CHOTARD]

Hi Marek

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for CAN1 pins, this is used on DRC Compact board.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>  arch/arm/dts/stm32mp15-pinctrl.dtsi | 20 ++++++++++++++++++++
>  1 file changed, 20 insertions(+)
> 
> diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> index 6a5b4016f66..e0965c5936e 100644
> --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> @@ -929,6 +929,26 @@
>  		};
>  	};
>  
> +	m_can1_pins_c: m-can1-2 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
> +			slew-rate = <1>;
> +			drive-push-pull;
> +			bias-disable;
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
> +			bias-disable;
> +		};
> +	};
> +
> +	m_can1_sleep_pins_c: m_can1-sleep-2 {
> +		pins {
> +			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
> +				 <STM32_PINMUX('H', 14, ANALOG)>; /* CAN1_RX */
> +		};
> +	};
> +
>  	m_can2_pins_a: m-can2-0 {
>  		pins1 {
>  			pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */

Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

Re: [PATCH 5/6] ARM: dts: stm32: Add alternate pinmux for SPI2 pins

[Patrice CHOTARD]

HI Marek

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for SPI2 pins, this is used on DRC Compact board.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>  arch/arm/dts/stm32mp15-pinctrl.dtsi | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> index e0965c5936e..b92a149a186 100644
> --- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
> +++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
> @@ -1778,6 +1778,21 @@
>  		};
>  	};
>  
> +	spi2_pins_b: spi2-1 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI1_SCK */
> +				 <STM32_PINMUX('I', 3, AF5)>; /* SPI1_MOSI */
> +			bias-disable;
> +			drive-push-pull;
> +			slew-rate = <1>;
> +		};
> +
> +		pins2 {
> +			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI1_MISO */
> +			bias-disable;
> +		};
> +	};
> +
>  	spi4_pins_a: spi4-0 {
>  		pins {
>  			pinmux = <STM32_PINMUX('E', 12, AF5)>, /* SPI4_SCK */

Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

Re: [PATCH 6/6] ARM: dts: stm32: Add DHCOR based DRC Compact board

[Patrice CHOTARD]

HI Marek

On 6/13/22 11:55, Marek Vasut wrote:
> Add DT for DH DRC Compact unit, which is a universal controller device.
> The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
> card slot, eMMC and SDIO Wi-Fi.
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>  arch/arm/dts/Makefile                         |   3 +-
>  .../arm/dts/stm32mp153c-dhcor-drc-compact.dts |  30 ++
>  .../stm32mp15xx-dhcor-drc-compact-u-boot.dtsi | 120 +++++++
>  .../arm/dts/stm32mp15xx-dhcor-drc-compact.dts |  16 +
>  .../dts/stm32mp15xx-dhcor-drc-compact.dtsi    | 326 ++++++++++++++++++
>  .../dh_stm32mp1/u-boot-dhcor.its              |  15 +
>  configs/stm32mp15_dhcor_basic_defconfig       |   1 +
>  7 files changed, 510 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
>  create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
>  create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
>  create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 0a2713c06a3..8a314210da6 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -1172,7 +1172,8 @@ dtb-$(CONFIG_STM32MP15x) += \
>  	stm32mp15xx-dhcom-drc02.dtb \
>  	stm32mp15xx-dhcom-pdk2.dtb \
>  	stm32mp15xx-dhcom-picoitx.dtb \
> -	stm32mp15xx-dhcor-avenger96.dtb
> +	stm32mp15xx-dhcor-avenger96.dtb \
> +	stm32mp15xx-dhcor-drc-compact.dtb
>  
>  dtb-$(CONFIG_SOC_K3_AM6) += \
>  	k3-am654-base-board.dtb \
> diff --git a/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts b/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
> new file mode 100644
> index 00000000000..c8b9818499e
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2022 Marek Vasut <marex@denx.de>
> + *
> + * DHCOR STM32MP1 variant:
> + * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG
> + * DHCOR PCB number: 586-100 or newer
> + * DRC Compact PCB number: 627-100 or newer
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp153.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15xx-dhcor-som.dtsi"
> +#include "stm32mp15xx-dhcor-drc-compact.dtsi"
> +
> +/ {
> +	model = "DH electronics STM32MP153C DHCOR DRC Compact";
> +	compatible = "dh,stm32mp153c-dhcor-drc-compact",
> +		     "dh,stm32mp153c-dhcor-som",
> +		     "st,stm32mp153";
> +};
> +
> +&m_can1 {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&m_can1_pins_c>;
> +	pinctrl-1 = <&m_can1_sleep_pins_c>;
> +	status = "okay";
> +};
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
> new file mode 100644
> index 00000000000..407fed56167
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2022 Marek Vasut <marex@denx.de>
> + */
> +
> +#include "stm32mp15xx-dhcor-u-boot.dtsi"
> +
> +/delete-node/ &ksz8851;
> +
> +/ {
> +	aliases {
> +		mmc0 = &sdmmc1;
> +		mmc1 = &sdmmc2;
> +		usb0 = &usbotg_hs;
> +		ethernet1 = &ks8851;
> +	};
> +
> +	config {
> +		dh,board-coding-gpios = <&gpioh 9 0>, <&gpioh 8 0>, <&gpioh 3 0>;
> +	};
> +
> +	/* This is actually on FMC2, but we do not have bus driver for that */
> +	ks8851: ks8851mll@64000000 {
> +		compatible = "micrel,ks8851-mll";
> +		reg = <0x64000000 0x20000>;
> +	};
> +};
> +
> +&ethernet0 {
> +	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
> +
> +	mdio0 {
> +		ethernet-phy@7 {
> +			reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <11000>;
> +			reset-deassert-us = <1000>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	/* These should bound to FMC2 bus driver, but we do not have one */
> +	pinctrl-0 = <&fmc_pins_b>;
> +	pinctrl-1 = <&fmc_sleep_pins_b>;
> +	pinctrl-names = "default", "sleep";
> +};
> +
> +&sdmmc1 {
> +	u-boot,dm-spl;
> +	st,use-ckin;
> +	st,cmd-gpios = <&gpiod 2 0>;
> +	st,ck-gpios = <&gpioc 12 0>;
> +	st,ckin-gpios = <&gpioe 4 0>;
> +};
> +
> +&sdmmc1_b4_pins_a {
> +	u-boot,dm-spl;
> +	pins1 {
> +		u-boot,dm-spl;
> +	};
> +	pins2 {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc1_dir_pins_b {
> +	u-boot,dm-spl;
> +	pins1 {
> +		u-boot,dm-spl;
> +	};
> +	pins2 {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc2 {
> +	u-boot,dm-spl;
> +};
> +
> +&sdmmc2_b4_pins_a {
> +	u-boot,dm-spl;
> +	pins1 {
> +		u-boot,dm-spl;
> +	};
> +	pins2 {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc2_d47_pins_c {
> +	u-boot,dm-spl;
> +	pins {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc3 {	/* SDIO Wi-Fi */
> +	status = "disabled";
> +};
> +
> +&uart4 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_d {
> +	u-boot,dm-pre-reloc;
> +	pins1 {
> +		u-boot,dm-pre-reloc;
> +	};
> +	pins2 {
> +		u-boot,dm-pre-reloc;
> +		/delete-property/ bias-disable;
> +		bias-pull-up;
> +	};
> +};
> +
> +&usbotg_hs {
> +	u-boot,force-b-session-valid;
> +	hnp-srp-disable;
> +};
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
> new file mode 100644
> index 00000000000..77dd944ff53
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2022 Marek Vasut <marex@denx.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp151.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15xx-dhcor-som.dtsi"
> +#include "stm32mp15xx-dhcor-drc-compact.dtsi"
> +
> +/ {
> +	model = "DH electronics STM32MP15xx DHCOR DRC Compact";
> +	compatible = "dh,stm32mp15xx-dhcor-drc-compact", "st,stm32mp1xx";
> +};
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
> new file mode 100644
> index 00000000000..bedccf0f00a
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
> @@ -0,0 +1,326 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2022 Marek Vasut <marex@denx.de>
> + */
> +
> +/ {
> +	aliases {
> +		ethernet0 = &ethernet0;
> +		ethernet1 = &ksz8851;
> +		mmc0 = &sdmmc1;
> +		rtc0 = &hwrtc;
> +		rtc1 = &rtc;
> +		serial0 = &uart4;
> +		serial1 = &uart8;
> +		serial2 = &usart3;
> +		serial3 = &uart5;
> +		spi0 = &qspi;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	led {
> +		compatible = "gpio-leds";
> +		led1 {
> +			label = "yellow:user0";
> +			gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
> +			default-state = "off";
> +		};
> +
> +		led2 {
> +			label = "red:user1";
> +			gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	ethernet_vio: vioregulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vio";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +		vin-supply = <&vdd>;
> +	};
> +};
> +
> +&adc {	/* X11 ADC inputs */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&adc12_ain_pins_b>;
> +	vdd-supply = <&vdd>;
> +	vdda-supply = <&vdda>;
> +	vref-supply = <&vdda>;
> +	status = "okay";
> +
> +	adc1: adc@0 {
> +		st,adc-channels = <0 1 6>;
> +		st,min-sample-time-nsecs = <5000>;
> +		status = "okay";
> +	};
> +
> +	adc2: adc@100 {
> +		st,adc-channels = <0 1 2>;
> +		st,min-sample-time-nsecs = <5000>;
> +		status = "okay";
> +	};
> +};
> +
> +&ethernet0 {
> +	status = "okay";
> +	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
> +	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
> +	pinctrl-names = "default", "sleep";
> +	phy-mode = "rgmii";
> +	max-speed = <1000>;
> +	phy-handle = <&phy0>;
> +
> +	mdio0 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
> +		reset-delay-us = <1000>;
> +		reset-post-delay-us = <1000>;
> +
> +		phy0: ethernet-phy@7 {
> +			reg = <7>;
> +
> +			rxc-skew-ps = <1500>;
> +			rxdv-skew-ps = <540>;
> +			rxd0-skew-ps = <420>;
> +			rxd1-skew-ps = <420>;
> +			rxd2-skew-ps = <420>;
> +			rxd3-skew-ps = <420>;
> +
> +			txc-skew-ps = <1440>;
> +			txen-skew-ps = <540>;
> +			txd0-skew-ps = <420>;
> +			txd1-skew-ps = <420>;
> +			txd2-skew-ps = <420>;
> +			txd3-skew-ps = <420>;
> +		};
> +	};
> +};
> +
> +&fmc {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&fmc_pins_b>;
> +	pinctrl-1 = <&fmc_sleep_pins_b>;
> +	status = "okay";
> +
> +	ksz8851: ethernet@1,0 {
> +		compatible = "micrel,ks8851-mll";
> +		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
> +		interrupt-parent = <&gpioc>;
> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +		bank-width = <2>;
> +
> +		/* Timing values are in nS */
> +		st,fmc2-ebi-cs-mux-enable;
> +		st,fmc2-ebi-cs-transaction-type = <4>;
> +		st,fmc2-ebi-cs-buswidth = <16>;
> +		st,fmc2-ebi-cs-address-setup-ns = <5>;
> +		st,fmc2-ebi-cs-address-hold-ns = <5>;
> +		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
> +		st,fmc2-ebi-cs-data-setup-ns = <45>;
> +		st,fmc2-ebi-cs-data-hold-ns = <1>;
> +		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
> +		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
> +		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
> +		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
> +		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
> +	};
> +};
> +
> +&gpioa {
> +	gpio-line-names = "", "", "", "",
> +			  "DRCC-VAR2", "", "", "",
> +			  "", "", "", "",
> +			  "", "", "", "";
> +};
> +
> +&gpioe {
> +	gpio-line-names = "", "", "", "",
> +			  "", "DRCC-GPIO0", "", "",
> +			  "", "", "", "",
> +			  "", "", "", "";
> +};
> +
> +&gpiog {
> +	gpio-line-names = "", "", "", "",
> +			  "", "", "", "",
> +			  "", "", "", "",
> +			  "DRCC-GPIO5", "", "", "";
> +};
> +
> +&gpioh {
> +	gpio-line-names = "", "", "", "DRCC-HW2",
> +			  "DRCC-GPIO4", "", "", "",
> +			  "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
> +			  "DRCC-VAR0", "", "", "DRCC-GPIO6";
> +};
> +
> +&gpioi {
> +	gpio-line-names = "", "", "", "",
> +			  "", "", "", "DRCC-GPIO2",
> +			  "", "DRCC-GPIO1", "", "",
> +			  "", "", "", "";
> +};
> +
> +&i2c1 {	/* X11 I2C1 */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins_b>;
> +	i2c-scl-rising-time-ns = <185>;
> +	i2c-scl-falling-time-ns = <20>;
> +	status = "okay";
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +};
> +
> +&i2c4 {
> +	hwrtc: rtc@32 {
> +		compatible = "microcrystal,rv8803";
> +		reg = <0x32>;
> +	};
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c04";
> +		reg = <0x50>;
> +		pagesize = <16>;
> +	};
> +};
> +
> +&sdmmc1 {	/* MicroSD */
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc1_b4_pins_a>;
> +	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> +	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> +	disable-wp;
> +	st,neg-edge;
> +	bus-width = <4>;
> +	vmmc-supply = <&vdd>;
> +	vqmmc-supply = <&vdd>;
> +	status = "okay";
> +};
> +
> +&sdmmc2 {	/* eMMC */
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
> +	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
> +	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
> +	bus-width = <8>;
> +	no-sd;
> +	no-sdio;
> +	non-removable;
> +	st,neg-edge;
> +	vmmc-supply = <&v3v3>;
> +	vqmmc-supply = <&vdd>;
> +	status = "okay";
> +};
> +
> +&sdmmc3 {	/* SDIO Wi-Fi */
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc3_b4_pins_a>;
> +	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
> +	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
> +	broken-cd;
> +	bus-width = <4>;
> +	mmc-ddr-3_3v;
> +	st,neg-edge;
> +	vmmc-supply = <&v3v3>;
> +	vqmmc-supply = <&v3v3>;
> +	status = "okay";
> +};
> +
> +&spi2 {	/* X11 SPI */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi2_pins_b>;
> +	cs-gpios = <&gpioi 0 0>;
> +	status = "disabled";
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +};
> +
> +&uart4 {
> +	label = "UART0";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart4_pins_d>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "okay";
> +};
> +
> +&uart5 {	/* X11 UART */
> +	label = "X11-UART5";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart5_pins_a>;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "okay";
> +};
> +
> +&uart8 {
> +	label = "RS485-1";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
> +	uart-has-rtscts;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "okay";
> +};
> +
> +&usart3 {	/* RS485 or RS232 */
> +	label = "RS485-2";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&usart3_pins_e>;
> +	pinctrl-1 = <&usart3_sleep_pins_e>;
> +	uart-has-rtscts;
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "okay";
> +};
> +
> +&usbh_ehci {
> +	phys = <&usbphyc_port0>;
> +	status = "okay";
> +};
> +
> +&usbh_ohci {
> +	phys = <&usbphyc_port0>;
> +	status = "okay";
> +};
> +
> +&usbotg_hs {
> +	dr_mode = "otg";
> +	pinctrl-0 = <&usbotg_hs_pins_a>;
> +	pinctrl-names = "default";
> +	phy-names = "usb2-phy";
> +	phys = <&usbphyc_port1 0>;
> +	vbus-supply = <&vbus_otg>;
> +	status = "okay";
> +};
> +
> +&usbphyc {
> +	status = "okay";
> +};
> +
> +&usbphyc_port0 {
> +	phy-supply = <&vdd_usb>;
> +	vdda1v1-supply = <&reg11>;
> +	vdda1v8-supply = <&reg18>;
> +	connector {
> +		compatible = "usb-a-connector";
> +		vbus-supply = <&vbus_sw>;
> +	};
> +};
> +
> +&usbphyc_port1 {
> +	phy-supply = <&vdd_usb>;
> +	vdda1v1-supply = <&reg11>;
> +	vdda1v8-supply = <&reg18>;
> +};
> diff --git a/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its b/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its
> index 0ea10a14972..de7dcb317f3 100644
> --- a/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its
> +++ b/board/dhelectronics/dh_stm32mp1/u-boot-dhcor.its
> @@ -23,6 +23,14 @@
>  			arch = "arm";
>  			compression = "none";
>  		};
> +
> +		fdt-2 {
> +			description = ".dtb";
> +			data = /incbin/("arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtb");
> +			type = "flat_dt";
> +			arch = "arm";
> +			compression = "none";
> +		};
>  	};
>  
>  	configurations {
> @@ -35,6 +43,13 @@
>  			fdt = "fdt-1";
>  		};
>  
> +		config-2 {
> +			/* DT+SoM+board model */
> +			description = "dh,stm32mp15xx-dhcor-drc-compact_somrev0_boardrev0";
> +			firmware = "uboot";
> +			fdt = "fdt-2";
> +		};
> +
>  		/* Add 586-200..586-400 with fdt-2..fdt-4 here */
>  	};
>  };
> diff --git a/configs/stm32mp15_dhcor_basic_defconfig b/configs/stm32mp15_dhcor_basic_defconfig
> index 0c4bca15402..32aa8b5dfaf 100644
> --- a/configs/stm32mp15_dhcor_basic_defconfig
> +++ b/configs/stm32mp15_dhcor_basic_defconfig
> @@ -109,6 +109,7 @@ CONFIG_PHY_MICREL=y
>  CONFIG_PHY_MICREL_KSZ90X1=y
>  CONFIG_DM_ETH=y
>  CONFIG_DWC_ETH_QOS=y
> +CONFIG_KS8851_MLL=y
>  CONFIG_PHY=y
>  CONFIG_SPL_PHY=y
>  CONFIG_PHY_STM32_USBPHYC=y
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>

Thanks
Patrice

Re: [PATCH 1/6] ARM: dts: stm32: Add alternate pinmux for UART3 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART3 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 41 +++++++++++++++++++++++++++++
>   1 file changed, 41 insertions(+)
>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Thanks
Patrick

Re: [PATCH 2/6] ARM: dts: stm32: Add alternate pinmux for UART4 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART4 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 30 +++++++++++++++++++++++++++++
>   1 file changed, 30 insertions(+)
>

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Thanks
Patrick

Re: [PATCH 3/6] ARM: dts: stm32: Add alternate pinmux for UART5 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART5 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 13 +++++++++++++
>   1 file changed, 13 insertions(+)
>

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Thanks
Patrick

Re: [PATCH 4/6] ARM: dts: stm32: Add alternate pinmux for CAN1 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for CAN1 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 20 ++++++++++++++++++++
>   1 file changed, 20 insertions(+)
>

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Thanks
Patrick

Re: [PATCH 5/6] ARM: dts: stm32: Add alternate pinmux for SPI2 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for SPI2 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 15 +++++++++++++++
>   1 file changed, 15 insertions(+)
>

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Thanks
Patrick

Re: [PATCH 6/6] ARM: dts: stm32: Add DHCOR based DRC Compact board

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add DT for DH DRC Compact unit, which is a universal controller device.
> The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
> card slot, eMMC and SDIO Wi-Fi.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/Makefile                         |   3 +-
>   .../arm/dts/stm32mp153c-dhcor-drc-compact.dts |  30 ++
>   .../stm32mp15xx-dhcor-drc-compact-u-boot.dtsi | 120 +++++++
>   .../arm/dts/stm32mp15xx-dhcor-drc-compact.dts |  16 +
>   .../dts/stm32mp15xx-dhcor-drc-compact.dtsi    | 326 ++++++++++++++++++
>   .../dh_stm32mp1/u-boot-dhcor.its              |  15 +
>   configs/stm32mp15_dhcor_basic_defconfig       |   1 +
>   7 files changed, 510 insertions(+), 1 deletion(-)
>   create mode 100644 arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
>   create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
>   create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
>   create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
>

Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

Thanks
Patrick

Re: [PATCH 1/6] ARM: dts: stm32: Add alternate pinmux for UART3 pins

[Patrick DELAUNAY]

Hi

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART3 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 41 +++++++++++++++++++++++++++++
>   1 file changed, 41 insertions(+)
>


Applied to u-boot-stm/master, thanks!

Regards
Patrick

Re: [PATCH 2/6] ARM: dts: stm32: Add alternate pinmux for UART4 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART4 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 30 +++++++++++++++++++++++++++++
>   1 file changed, 30 insertions(+)
>



Applied to u-boot-stm/master, thanks!

Regards
Patrick

Re: [PATCH 3/6] ARM: dts: stm32: Add alternate pinmux for UART5 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for UART5 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 13 +++++++++++++
>   1 file changed, 13 insertions(+)
>



Applied to u-boot-stm/master, thanks!

Regards
Patrick

Re: [PATCH 4/6] ARM: dts: stm32: Add alternate pinmux for CAN1 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for CAN1 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 20 ++++++++++++++++++++
>   1 file changed, 20 insertions(+)
>



Applied to u-boot-stm/master, thanks!

Regards
Patrick

Re: [PATCH 5/6] ARM: dts: stm32: Add alternate pinmux for SPI2 pins

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add another mux option for SPI2 pins, this is used on DRC Compact board.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/stm32mp15-pinctrl.dtsi | 15 +++++++++++++++
>   1 file changed, 15 insertions(+)
>



Applied to u-boot-stm/master, thanks!

Regards
Patrick

Re: [PATCH 6/6] ARM: dts: stm32: Add DHCOR based DRC Compact board

[Patrick DELAUNAY]

Hi,

On 6/13/22 11:55, Marek Vasut wrote:
> Add DT for DH DRC Compact unit, which is a universal controller device.
> The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
> card slot, eMMC and SDIO Wi-Fi.
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Patrice Chotard <patrice.chotard@foss.st.com>
> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
> ---
>   arch/arm/dts/Makefile                         |   3 +-
>   .../arm/dts/stm32mp153c-dhcor-drc-compact.dts |  30 ++
>   .../stm32mp15xx-dhcor-drc-compact-u-boot.dtsi | 120 +++++++
>   .../arm/dts/stm32mp15xx-dhcor-drc-compact.dts |  16 +
>   .../dts/stm32mp15xx-dhcor-drc-compact.dtsi    | 326 ++++++++++++++++++
>   .../dh_stm32mp1/u-boot-dhcor.its              |  15 +
>   configs/stm32mp15_dhcor_basic_defconfig       |   1 +
>   7 files changed, 510 insertions(+), 1 deletion(-)
>   create mode 100644 arch/arm/dts/stm32mp153c-dhcor-drc-compact.dts
>   create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact-u-boot.dtsi
>   create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dts
>   create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-drc-compact.dtsi
>

Applied to u-boot-stm/master, thanks!

Regards
Patrick