From: Marcel Ziswiler <marcel@ziswiler.com>
To: u-boot@lists.denx.de
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>,
Adam Ford <aford173@gmail.com>,
Fabio Estevam <festevam@gmail.com>, Ian Ray <ian.ray@ge.com>,
Jagan Teki <jagan@amarulasolutions.com>,
Martyn Welch <martyn.welch@collabora.com>,
Matthias Winker <matthias.winker@de.bosch.com>,
"NXP i.MX U-Boot Team" <uboot-imx@nxp.com>,
Philip Oberfichtner <pro@denx.de>,
Raffaele RECALCATI <raffaele.recalcati@bticino.it>,
Simone CIANNI <simone.cianni@bticino.it>,
Soeren Moch <smoch@web.de>, Stefano Babic <sbabic@denx.de>,
Tim Harvey <tharvey@gateworks.com>,
Troy Kisky <troy.kisky@boundarydevices.com>
Subject: [PATCH v1 04/26] imx6dl/imx6qdl: synchronise device trees with linux
Date: Thu, 21 Jul 2022 15:27:26 +0200 [thread overview]
Message-ID: <20220721132748.1052244-5-marcel@ziswiler.com> (raw)
In-Reply-To: <20220721132748.1052244-1-marcel@ziswiler.com>
From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device trees with linux-next next-20220708.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
---
arch/arm/dts/imx6-logicpd-baseboard.dtsi | 12 +-
arch/arm/dts/imx6-logicpd-som.dtsi | 4 +
arch/arm/dts/imx6dl-mamoj.dts | 273 +++++-
arch/arm/dts/imx6dl-mba6.dtsi | 10 +-
arch/arm/dts/imx6dl-mba6a.dts | 15 +-
arch/arm/dts/imx6dl-mba6b.dts | 15 +-
arch/arm/dts/imx6dl-nitrogen6x.dts | 12 +-
arch/arm/dts/imx6dl-pinfunc.h | 7 +-
arch/arm/dts/imx6dl-riotboard.dts | 2 +
arch/arm/dts/imx6dl-sabreauto.dts | 15 +
arch/arm/dts/imx6dl-tqma6a.dtsi | 12 +-
arch/arm/dts/imx6dl-tqma6b.dtsi | 12 +-
arch/arm/dts/imx6dl.dtsi | 15 +-
arch/arm/dts/imx6q-b450v3.dts | 19 +-
arch/arm/dts/imx6q-b650v3.dts | 17 +-
arch/arm/dts/imx6q-b850v3.dts | 23 +-
arch/arm/dts/imx6q-ba16.dtsi | 18 +-
arch/arm/dts/imx6q-bosch-acc.dts | 14 +-
arch/arm/dts/imx6q-bx50v3.dtsi | 61 +-
arch/arm/dts/imx6q-cm-fx6.dts | 112 ++-
arch/arm/dts/imx6q-icore-ofcap10.dts | 28 +-
arch/arm/dts/imx6q-logicpd.dts | 18 +-
arch/arm/dts/imx6q-marsboard.dts | 2 +-
arch/arm/dts/imx6q-mba6.dtsi | 32 +-
arch/arm/dts/imx6q-mba6a.dts | 14 +-
arch/arm/dts/imx6q-mba6b.dts | 14 +-
arch/arm/dts/imx6q-mccmon6.dts | 213 +++--
arch/arm/dts/imx6q-nitrogen6x.dts | 12 +-
arch/arm/dts/imx6q-novena.dts | 42 +-
arch/arm/dts/imx6q-phytec-mira-rdk-nand.dts | 3 +
arch/arm/dts/imx6q-pinfunc.h | 7 +-
arch/arm/dts/imx6q-sabrelite.dts | 6 +-
arch/arm/dts/imx6q-tbs2910.dts | 9 +-
arch/arm/dts/imx6q-tqma6a.dtsi | 12 +-
arch/arm/dts/imx6q-tqma6b.dtsi | 11 +-
arch/arm/dts/imx6q.dtsi | 40 +-
arch/arm/dts/imx6qdl-cubox-i.dtsi | 5 +-
arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi | 6 +-
arch/arm/dts/imx6qdl-dhcom-som.dtsi | 8 +-
arch/arm/dts/imx6qdl-gw51xx.dtsi | 7 +-
arch/arm/dts/imx6qdl-gw52xx.dtsi | 10 +-
arch/arm/dts/imx6qdl-gw53xx.dtsi | 22 +-
arch/arm/dts/imx6qdl-gw54xx.dtsi | 22 +-
arch/arm/dts/imx6qdl-gw551x.dtsi | 7 +-
arch/arm/dts/imx6qdl-gw552x.dtsi | 29 +-
arch/arm/dts/imx6qdl-gw553x.dtsi | 5 +-
arch/arm/dts/imx6qdl-gw560x.dtsi | 14 +-
arch/arm/dts/imx6qdl-gw5903.dtsi | 6 -
arch/arm/dts/imx6qdl-gw5904.dtsi | 27 +-
arch/arm/dts/imx6qdl-gw5907.dtsi | 9 +-
arch/arm/dts/imx6qdl-gw5910.dtsi | 7 -
arch/arm/dts/imx6qdl-gw5912.dtsi | 22 +-
arch/arm/dts/imx6qdl-gw5913.dtsi | 10 +-
arch/arm/dts/imx6qdl-hummingboard2.dtsi | 2 +-
arch/arm/dts/imx6qdl-icore.dtsi | 19 +-
arch/arm/dts/imx6qdl-mba6.dtsi | 598 ++++++++++---
arch/arm/dts/imx6qdl-mba6a.dtsi | 35 +-
arch/arm/dts/imx6qdl-mba6b.dtsi | 40 +-
arch/arm/dts/imx6qdl-nitrogen6x.dtsi | 733 ++++++++++++++--
.../dts/imx6qdl-phytec-mira-peb-av-02.dtsi | 119 +++
.../dts/imx6qdl-phytec-mira-peb-eval-01.dtsi | 71 ++
.../dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi | 85 ++
arch/arm/dts/imx6qdl-phytec-mira.dtsi | 32 +-
arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi | 30 +-
arch/arm/dts/imx6qdl-pico.dtsi | 226 ++++-
arch/arm/dts/imx6qdl-sabreauto.dtsi | 119 ++-
arch/arm/dts/imx6qdl-sabrelite.dtsi | 828 +++++++++++++-----
arch/arm/dts/imx6qdl-sabresd.dtsi | 214 +++--
arch/arm/dts/imx6qdl-sr-som-ti.dtsi | 1 +
arch/arm/dts/imx6qdl-sr-som.dtsi | 31 +-
arch/arm/dts/imx6qdl-tqma6.dtsi | 326 +++----
arch/arm/dts/imx6qdl-tqma6a.dtsi | 46 +-
arch/arm/dts/imx6qdl-tqma6b.dtsi | 28 +-
arch/arm/dts/imx6qdl-udoo.dtsi | 4 +-
arch/arm/dts/imx6qdl-wandboard-revd1.dtsi | 2 -
arch/arm/dts/imx6qdl-wandboard.dtsi | 102 ++-
arch/arm/dts/imx6qdl.dtsi | 194 ++--
include/dt-bindings/clock/imx6qdl-clock.h | 14 +-
78 files changed, 3953 insertions(+), 1293 deletions(-)
create mode 100644 arch/arm/dts/imx6qdl-phytec-mira-peb-av-02.dtsi
create mode 100644 arch/arm/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi
create mode 100644 arch/arm/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
diff --git a/arch/arm/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/dts/imx6-logicpd-baseboard.dtsi
index c40a7af6ebe..d9de9b4f0c5 100644
--- a/arch/arm/dts/imx6-logicpd-baseboard.dtsi
+++ b/arch/arm/dts/imx6-logicpd-baseboard.dtsi
@@ -212,6 +212,7 @@
&ecspi1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
status = "disabled";
};
@@ -237,7 +238,6 @@
compatible = "wlf,wm8962";
reg = <0x1a>;
clocks = <&clks IMX6QDL_CLK_CKO>;
- clock-names = "xclk";
DCVDD-supply = <®_audio>;
DBVDD-supply = <®_audio>;
AVDD-supply = <®_audio>;
@@ -249,9 +249,9 @@
gpio-cfg = <
0x0000 /* 0:Default */
0x0000 /* 1:Default */
- 0x0013 /* 2:FN_DMICCLK */
+ 0x0000 /* 2:FN_DMICCLK */
0x0000 /* 3:Default */
- 0x8014 /* 4:FN_DMICCDAT */
+ 0x0000 /* 4:FN_DMICCDAT */
0x0000 /* 5:Default */
>;
};
@@ -328,6 +328,10 @@
pinctrl-0 = <&pinctrl_pwm3>;
};
+&snvs_pwrkey {
+ status = "okay";
+};
+
&ssi2 {
status = "okay";
};
@@ -379,7 +383,7 @@
MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0 0x100b1
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
>;
};
diff --git a/arch/arm/dts/imx6-logicpd-som.dtsi b/arch/arm/dts/imx6-logicpd-som.dtsi
index 7ceae357324..547fb141ec0 100644
--- a/arch/arm/dts/imx6-logicpd-som.dtsi
+++ b/arch/arm/dts/imx6-logicpd-som.dtsi
@@ -207,6 +207,10 @@
vin-supply = <&sw1c_reg>;
};
+&snvs_poweroff {
+ status = "okay";
+};
+
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
diff --git a/arch/arm/dts/imx6dl-mamoj.dts b/arch/arm/dts/imx6dl-mamoj.dts
index 3f6d8aa4a25..028951955bd 100644
--- a/arch/arm/dts/imx6dl-mamoj.dts
+++ b/arch/arm/dts/imx6dl-mamoj.dts
@@ -12,6 +12,156 @@
/ {
model = "BTicino i.MX6DL Mamoj board";
compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl";
+
+ /* Will be filled by the bootloader */
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm3 0 25000>; /* 25000ns -> 40kHz */
+ brightness-levels = <0 4 8 16 32 64 128 160 192 224 255>;
+ default-brightness-level = <7>;
+ };
+
+ display: disp0 {
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ lcd_display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+ };
+
+ panel-lcd {
+ compatible = "rocktech,rk070er9427";
+ backlight = <&backlight_lcd>;
+ power-supply = <®_lcd_lr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_lcdif_pwr>;
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
+
+ reg_lcd_3v3: regulator-lcd-dvdd {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-dvdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 1 0>;
+ enable-active-high;
+ startup-delay-us = <21000>;
+ };
+
+ reg_lcd_power: regulator-lcd-power {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-enable";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 6 0>;
+ enable-active-high;
+ vin-supply = <®_lcd_3v3>;
+ };
+
+ reg_lcd_vgl: regulator-lcd-vgl {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-vgl";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <6000>;
+ enable-active-high;
+ vin-supply = <®_lcd_power>;
+ };
+
+ reg_lcd_vgh: regulator-lcd-vgh {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-vgh";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <6000>;
+ enable-active-high;
+ vin-supply = <®_lcd_avdd>;
+ };
+
+ reg_lcd_vcom: regulator-lcd-vcom {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-vcom";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <11000>;
+ enable-active-high;
+ vin-supply = <®_lcd_vgh>;
+ };
+
+ reg_lcd_lr: regulator-lcd-lr {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-lr";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_lcd_vcom>;
+ };
+
+ reg_lcd_avdd: regulator-lcd-avdd {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-avdd";
+ regulator-min-microvolt = <10280000>;
+ regulator-max-microvolt = <10280000>;
+ gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <6000>;
+ enable-active-high;
+ vin-supply = <®_lcd_vgl>;
+ };
+
+ reg_usb_host: regulator-usb-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbhost-vbus";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbhost>;
+ regulator-min-microvolt = <50000000>;
+ regulator-max-microvolt = <50000000>;
+ gpio = <&gpio6 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_wl18xx_vmmc: regulator-wl18xx-vmcc {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1807";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wlan>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
};
&fec {
@@ -34,7 +184,7 @@
pinctrl-0 = <&pinctrl_i2c4>;
status = "okay";
- pmic: pfuze100@08 {
+ pfuze100: pmic@8 {
compatible = "fsl,pfuze100";
reg = <0x08>;
@@ -148,12 +298,57 @@
};
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm3 {
+ #pwm-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
+&usbh1 {
+ vbus-supply = <®_usb_host>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ bus-width = <4>;
+ vmmc-supply = <®_wl18xx_vmmc>;
+ no-1-8-v;
+ non-removable;
+ wakeup-source;
+ keep-power-in-suspend;
+ cap-power-off-card;
+ max-frequency = <25000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1837";
+ reg = <2>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+ tcxo-clock-frequency = <26000000>;
+ };
+};
+
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
@@ -201,6 +396,59 @@
>;
};
+ pinctrl_ipu1_lcdif: pinctrlipu1lcdif { /* parallel port 24-bit */
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 /* VDOUT_PCLK */
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 /* VDOUT_HSYNC */
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 /* VDOUT_VSYNC */
+ MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x10 /* VDOUT_RESET */
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_ipu1_lcdif_pwr: ipu1lcdifpwrgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x40013058 /* EN_LCD33V */
+ MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x4001b0b0 /* EN_AVDD */
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x40013058 /* ENVGH */
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x40013058 /* ENVGL */
+ MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x40013058 /* LCD_POWER */
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x40013058 /* EN_VCOM_LCD */
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x40013058 /* LCD_L_R */
+ MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x40013058 /* LCD_U_D */
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
@@ -208,6 +456,23 @@
>;
};
+ pinctrl_usbhost: usbhostgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x4001b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17069
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10079
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17069
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17069
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17069
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17069
+ >;
+ };
+
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
@@ -222,4 +487,10 @@
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
>;
};
+
+ pinctrl_wlan: wlangrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x4001b0b0
+ >;
+ };
};
diff --git a/arch/arm/dts/imx6dl-mba6.dtsi b/arch/arm/dts/imx6dl-mba6.dtsi
index d74adf2b288..b749b424bbd 100644
--- a/arch/arm/dts/imx6dl-mba6.dtsi
+++ b/arch/arm/dts/imx6dl-mba6.dtsi
@@ -1,6 +1,10 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
ðphy {
rxdv-skew-ps = <180>;
diff --git a/arch/arm/dts/imx6dl-mba6a.dts b/arch/arm/dts/imx6dl-mba6a.dts
index fc9cc2c056f..df0a96b28af 100644
--- a/arch/arm/dts/imx6dl-mba6a.dts
+++ b/arch/arm/dts/imx6dl-mba6a.dts
@@ -1,6 +1,10 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
/dts-v1/;
@@ -11,6 +15,7 @@
#include "imx6dl-mba6.dtsi"
/ {
- model = "TQ TQMa6S on MBa6x";
- compatible = "tq,mba6a", "tq,tqma6dl", "fsl,imx6dl";
+ model = "TQ TQMa6S/DL on MBa6x";
+ compatible = "tq,imx6dl-mba6x-a", "tq,mba6a",
+ "tq,imx6dl-tqma6dl-a", "fsl,imx6dl";
};
diff --git a/arch/arm/dts/imx6dl-mba6b.dts b/arch/arm/dts/imx6dl-mba6b.dts
index a3c8d9d4c6b..610b19d2db0 100644
--- a/arch/arm/dts/imx6dl-mba6b.dts
+++ b/arch/arm/dts/imx6dl-mba6b.dts
@@ -1,6 +1,10 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
/dts-v1/;
@@ -11,6 +15,7 @@
#include "imx6dl-mba6.dtsi"
/ {
- model = "TQ TQMa6S on MBa6x";
- compatible = "tq,mba6b", "tq,tqma6dl", "fsl,imx6dl";
+ model = "TQ TQMa6S/DL on MBa6x";
+ compatible = "tq,imx6dl-mba6x-b", "tq,mba6b",
+ "tq,imx6dl-tqma6dl-b", "fsl,imx6dl";
};
diff --git a/arch/arm/dts/imx6dl-nitrogen6x.dts b/arch/arm/dts/imx6dl-nitrogen6x.dts
index 9427ab6399b..ef58d3b0ea0 100644
--- a/arch/arm/dts/imx6dl-nitrogen6x.dts
+++ b/arch/arm/dts/imx6dl-nitrogen6x.dts
@@ -1,11 +1,11 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2013-2019 Boundary Devices, Inc.
-// Copyright 2012 Freescale Semiconductor, Inc.
-// Copyright 2011 Linaro Ltd.
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2013 Boundary Devices, Inc.
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
/dts-v1/;
-
#include "imx6dl.dtsi"
#include "imx6qdl-nitrogen6x.dtsi"
diff --git a/arch/arm/dts/imx6dl-pinfunc.h b/arch/arm/dts/imx6dl-pinfunc.h
index 0ead323fdbd..9d88d09f9bf 100644
--- a/arch/arm/dts/imx6dl-pinfunc.h
+++ b/arch/arm/dts/imx6dl-pinfunc.h
@@ -1,10 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Copyright 2013 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
*/
#ifndef __DTS_IMX6DL_PINFUNC_H
@@ -668,6 +664,7 @@
#define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1f4 0x5c4 0x8f0 0x3 0x1
#define MX6QDL_PAD_ENET_RX_ER__ENET_1588_EVENT2_OUT 0x1f4 0x5c4 0x000 0x4 0x0
#define MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1f4 0x5c4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x1f8 0x5c8 0x000 0x0 0x0
#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1f8 0x5c8 0x818 0x1 0x0
#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1f8 0x5c8 0x838 0x2 0x0
#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1f8 0x5c8 0x000 0x3 0x0
diff --git a/arch/arm/dts/imx6dl-riotboard.dts b/arch/arm/dts/imx6dl-riotboard.dts
index 065d3ab0f50..e7d9bfbfd0e 100644
--- a/arch/arm/dts/imx6dl-riotboard.dts
+++ b/arch/arm/dts/imx6dl-riotboard.dts
@@ -106,6 +106,8 @@
reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <1000>;
+ qca,smarteee-tw-us-1g = <24>;
+ qca,clk-out-frequency = <125000000>;
};
};
};
diff --git a/arch/arm/dts/imx6dl-sabreauto.dts b/arch/arm/dts/imx6dl-sabreauto.dts
index 660d52a245b..ff3283c83a3 100644
--- a/arch/arm/dts/imx6dl-sabreauto.dts
+++ b/arch/arm/dts/imx6dl-sabreauto.dts
@@ -11,3 +11,18 @@
model = "Freescale i.MX6 DualLite/Solo SABRE Automotive Board";
compatible = "fsl,imx6dl-sabreauto", "fsl,imx6dl";
};
+
+&cpu0 {
+ operating-points = <
+ /* kHz uV */
+ 996000 1275000
+ 792000 1175000
+ 396000 1150000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 996000 1200000
+ 792000 1175000
+ 396000 1175000
+ >;
+};
diff --git a/arch/arm/dts/imx6dl-tqma6a.dtsi b/arch/arm/dts/imx6dl-tqma6a.dtsi
index df87b381cae..e891ef9b009 100644
--- a/arch/arm/dts/imx6dl-tqma6a.dtsi
+++ b/arch/arm/dts/imx6dl-tqma6a.dtsi
@@ -1,14 +1,16 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
#include "imx6dl.dtsi"
#include "imx6qdl-tqma6a.dtsi"
#include "imx6qdl-tqma6.dtsi"
/ {
- memory {
+ memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x20000000>;
};
};
-
diff --git a/arch/arm/dts/imx6dl-tqma6b.dtsi b/arch/arm/dts/imx6dl-tqma6b.dtsi
index 47ffbc4d952..38cd8501a88 100644
--- a/arch/arm/dts/imx6dl-tqma6b.dtsi
+++ b/arch/arm/dts/imx6dl-tqma6b.dtsi
@@ -1,14 +1,16 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
#include "imx6dl.dtsi"
#include "imx6qdl-tqma6b.dtsi"
#include "imx6qdl-tqma6.dtsi"
/ {
- memory {
+ memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x20000000>;
};
};
-
diff --git a/arch/arm/dts/imx6dl.dtsi b/arch/arm/dts/imx6dl.dtsi
index ae5aad6b9ef..8e0ed209ede 100644
--- a/arch/arm/dts/imx6dl.dtsi
+++ b/arch/arm/dts/imx6dl.dtsi
@@ -15,7 +15,7 @@
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0>;
@@ -44,6 +44,8 @@
arm-supply = <®_arm>;
pu-supply = <®_pu>;
soc-supply = <®_soc>;
+ nvmem-cells = <&cpu_speed_grade>;
+ nvmem-cell-names = "speed_grade";
};
cpu@1 {
@@ -64,6 +66,7 @@
396000 1175000
>;
clock-latency = <61036>; /* two CLK32 periods */
+ #cooling-cells = <2>;
clocks = <&clks IMX6QDL_CLK_ARM>,
<&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
<&clks IMX6QDL_CLK_STEP>,
@@ -77,7 +80,7 @@
};
};
- soc {
+ soc: soc {
ocram: sram@900000 {
compatible = "mmio-sram";
reg = <0x00900000 0x20000>;
@@ -85,10 +88,6 @@
};
aips1: bus@2000000 {
- iomuxc: iomuxc@20e0000 {
- compatible = "fsl,imx6dl-iomuxc";
- };
-
pxp: pxp@20f0000 {
reg = <0x020f0000 0x4000>;
interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
@@ -295,6 +294,10 @@
compatible = "fsl,imx6dl-hdmi";
};
+&iomuxc {
+ compatible = "fsl,imx6dl-iomuxc";
+};
+
&ipu1_csi1 {
ipu1_csi1_from_ipu1_csi1_mux: endpoint {
remote-endpoint = <&ipu1_csi1_mux_to_ipu1_csi1>;
diff --git a/arch/arm/dts/imx6q-b450v3.dts b/arch/arm/dts/imx6q-b450v3.dts
index 995caa8a331..d994b32ad82 100644
--- a/arch/arm/dts/imx6q-b450v3.dts
+++ b/arch/arm/dts/imx6q-b450v3.dts
@@ -1,4 +1,3 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Copyright 2015 Timesys Corporation.
* Copyright 2015 General Electric Company
@@ -66,13 +65,6 @@
};
};
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
- <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
- <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
&ldb {
status = "okay";
@@ -92,14 +84,19 @@
};
&pca9539 {
- P04 {
+ gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN",
+ "", "SM_D_ACT", "DP1_RST#", "",
+ "WD15S_EN", "WD15S_DIS#", "", "",
+ "", "", "", "";
+
+ P04-hog {
gpio-hog;
gpios = <4 0>;
output-low;
line-name = "PCA9539-P04";
};
- P07 {
+ P07-hog {
gpio-hog;
gpios = <7 0>;
output-low;
@@ -158,5 +155,3 @@
};
};
};
-
-#include "imx6q-bx50v3-uboot.dtsi"
diff --git a/arch/arm/dts/imx6q-b650v3.dts b/arch/arm/dts/imx6q-b650v3.dts
index 95a61347da5..fa1a1df37cd 100644
--- a/arch/arm/dts/imx6q-b650v3.dts
+++ b/arch/arm/dts/imx6q-b650v3.dts
@@ -1,4 +1,3 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Copyright 2015 Timesys Corporation.
* Copyright 2015 General Electric Company
@@ -66,13 +65,6 @@
};
};
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
- <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
- <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
&ldb {
status = "okay";
@@ -92,7 +84,12 @@
};
&pca9539 {
- P07 {
+ gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN",
+ "", "SM_D_ACT", "DP1_RST#", "",
+ "WD15S_EN", "WD15S_DIS#", "", "",
+ "", "", "", "";
+
+ P07-hog {
gpio-hog;
gpios = <7 0>;
output-low;
@@ -157,5 +154,3 @@
};
};
};
-
-#include "imx6q-bx50v3-uboot.dtsi"
diff --git a/arch/arm/dts/imx6q-b850v3.dts b/arch/arm/dts/imx6q-b850v3.dts
index 6416825234b..db8c332df6a 100644
--- a/arch/arm/dts/imx6q-b850v3.dts
+++ b/arch/arm/dts/imx6q-b850v3.dts
@@ -1,4 +1,3 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Copyright 2015 Timesys Corporation.
* Copyright 2015 General Electric Company
@@ -54,17 +53,6 @@
};
};
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
- <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
- <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
- <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
- <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
- <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
- <&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
-};
-
&ldb {
fsl,dual-channel;
status = "okay";
@@ -211,14 +199,19 @@
};
&pca9539 {
- P10 {
+ gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN",
+ "REMOTE_ON_PML#", "SM_D_ACT", "DP1_RST#", "DP2_RST#",
+ "", "", "", "",
+ "", "", "", "";
+
+ P10-hog {
gpio-hog;
gpios = <8 0>;
output-low;
line-name = "PCA9539-P10";
};
- P11 {
+ P11-hog {
gpio-hog;
gpios = <9 0>;
output-low;
@@ -300,5 +293,3 @@
phy-handle = <&switchphy4>;
};
};
-
-#include "imx6q-bx50v3-uboot.dtsi"
diff --git a/arch/arm/dts/imx6q-ba16.dtsi b/arch/arm/dts/imx6q-ba16.dtsi
index 9da2bb6e869..f266f1b7e0c 100644
--- a/arch/arm/dts/imx6q-ba16.dtsi
+++ b/arch/arm/dts/imx6q-ba16.dtsi
@@ -1,4 +1,3 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Support for imx6 based Advantech DMS-BA16 Qseven module
*
@@ -125,6 +124,9 @@
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
};
@@ -135,12 +137,12 @@
};
&ecspi1 {
- cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
- flash: n25q032@0 {
+ flash: flash@0 {
compatible = "jedec,spi-nor";
#address-cells = <1>;
#size-cells = <1>;
@@ -173,8 +175,9 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- status = "okay";
+ phy-supply = <®_3p3v>;
phy-handle = <&phy0>;
+ status = "okay";
mdio {
#address-cells = <1>;
@@ -346,6 +349,7 @@
};
&pwm1 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
@@ -586,6 +590,12 @@
>;
};
+ pinctrl_usbotg_vbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
diff --git a/arch/arm/dts/imx6q-bosch-acc.dts b/arch/arm/dts/imx6q-bosch-acc.dts
index 1bd4ef2fe4e..8263bfef9bf 100644
--- a/arch/arm/dts/imx6q-bosch-acc.dts
+++ b/arch/arm/dts/imx6q-bosch-acc.dts
@@ -554,13 +554,23 @@
status = "okay";
};
+&usbphynop1 {
+ clocks = <&clks IMX6QDL_CLK_USBPHY1>;
+ clock-names = "main_clk";
+ vcc-supply = <®_usb_h1_vbus>;
+};
+
+&usbphynop2 {
+ vcc-supply = <®_usb_h2_vbus>;
+};
+
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
no-1-8-v;
keep-power-in-suspend;
- enable-sdio-wakeup;
+ wakeup-source;
voltage-ranges = <3300 3300>;
vmmc-supply = <®_sw4>;
fsl,wp-controller;
@@ -584,7 +594,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog1>;
fsl,ext-reset-output;
- timeout-sec=<10>;
+ timeout-sec = <10>;
status = "okay";
};
diff --git a/arch/arm/dts/imx6q-bx50v3.dtsi b/arch/arm/dts/imx6q-bx50v3.dtsi
index 19829613c04..ead83091e19 100644
--- a/arch/arm/dts/imx6q-bx50v3.dtsi
+++ b/arch/arm/dts/imx6q-bx50v3.dtsi
@@ -1,4 +1,3 @@
-// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
* Copyright 2015 Timesys Corporation.
* Copyright 2015 General Electric Company
@@ -103,10 +102,15 @@
#address-cells = <1>;
#size-cells = <0>;
- switch@0 {
+ switch: switch@0 {
compatible = "marvell,mv88e6085"; /* 88e6240*/
reg = <0>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
switch_ports: ports {
#address-cells = <1>;
#size-cells = <0>;
@@ -118,22 +122,32 @@
switchphy0: switchphy@0 {
reg = <0>;
+ interrupt-parent = <&switch>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
};
switchphy1: switchphy@1 {
reg = <1>;
+ interrupt-parent = <&switch>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
};
switchphy2: switchphy@2 {
reg = <2>;
+ interrupt-parent = <&switch>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
};
switchphy3: switchphy@3 {
reg = <3>;
+ interrupt-parent = <&switch>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
};
switchphy4: switchphy@4 {
reg = <4>;
+ interrupt-parent = <&switch>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
};
};
};
@@ -141,12 +155,12 @@
};
&ecspi5 {
- cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi5>;
status = "okay";
- m25_eeprom: m25p80@0 {
+ m25_eeprom: flash@0 {
compatible = "atmel,at25";
spi-max-frequency = <10000000>;
size = <0x8000>;
@@ -159,8 +173,8 @@
&i2c1 {
pinctrl-names = "default", "gpio";
pinctrl-1 = <&pinctrl_i2c1_gpio>;
- sda-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
- scl-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
pca9547: mux@70 {
compatible = "nxp,pca9547";
@@ -234,42 +248,42 @@
interrupt-parent = <&gpio2>;
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- P12 {
+ P12-hog {
gpio-hog;
gpios = <10 0>;
output-low;
line-name = "PCA9539-P12";
};
- P13 {
+ P13-hog {
gpio-hog;
gpios = <11 0>;
output-low;
line-name = "PCA9539-P13";
};
- P14 {
+ P14-hog {
gpio-hog;
gpios = <12 0>;
output-low;
line-name = "PCA9539-P14";
};
- P15 {
+ P15-hog {
gpio-hog;
gpios = <13 0>;
output-low;
line-name = "PCA9539-P15";
};
- P16 {
+ P16-hog {
gpio-hog;
gpios = <14 0>;
output-low;
line-name = "PCA9539-P16";
};
- P17 {
+ P17-hog {
gpio-hog;
gpios = <15 0>;
output-low;
@@ -301,15 +315,15 @@
&i2c2 {
pinctrl-names = "default", "gpio";
pinctrl-1 = <&pinctrl_i2c2_gpio>;
- sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
- scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
&i2c3 {
pinctrl-names = "default", "gpio";
pinctrl-1 = <&pinctrl_i2c3_gpio>;
- sda-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
- scl-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
&iomuxc {
@@ -379,4 +393,17 @@
};
};
-#include "imx6q-bx50v3-uboot.dtsi"
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI1_PRE_SEL>,
+ <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>,
+ <&clks IMX6QDL_CLK_IPU2_DI1_PRE_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+ <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+ <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+ <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+ <&clks IMX6QDL_CLK_PLL2_PFD0_352M>,
+ <&clks IMX6QDL_CLK_PLL2_PFD0_352M>;
+};
diff --git a/arch/arm/dts/imx6q-cm-fx6.dts b/arch/arm/dts/imx6q-cm-fx6.dts
index 1f574c5eb57..1ad41c944b4 100644
--- a/arch/arm/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/dts/imx6q-cm-fx6.dts
@@ -43,13 +43,15 @@
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
#include "imx6q.dtsi"
/ {
model = "CompuLab CM-FX6";
compatible = "compulab,cm-fx6", "fsl,imx6q";
- memory {
+ memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x80000000>;
};
@@ -134,10 +136,35 @@
};
};
-/*
- * The U-Boot: audio mux node has been removed because the required dt-bindings
- * header file is not present in the U-Boot.
- */
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ ssi2 {
+ fsl,audmux-port = <1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_RCLKDIR |
+ IMX_AUDMUX_V2_PTCR_RCSEL(3 | 0x8) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(3))
+ IMX_AUDMUX_V2_PDCR_RXDSEL(3)
+ >;
+ };
+
+ audmux4 {
+ fsl,audmux-port = <3>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(1) |
+ IMX_AUDMUX_V2_PTCR_RCLKDIR |
+ IMX_AUDMUX_V2_PTCR_RCSEL(1 | 0x8) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(1))
+ IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+ >;
+ };
+};
&cpu0 {
/*
@@ -161,13 +188,79 @@
>;
};
+&cpu1 {
+ /*
+ * Although the imx6q fuse indicates that 1.2GHz operation is possible,
+ * the module behaves unstable at this frequency. Hence, remove the
+ * 1.2GHz operation point here.
+ */
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 975000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 1175000
+ >;
+};
+
+&cpu2 {
+ /*
+ * Although the imx6q fuse indicates that 1.2GHz operation is possible,
+ * the module behaves unstable at this frequency. Hence, remove the
+ * 1.2GHz operation point here.
+ */
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 975000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 1175000
+ >;
+};
+
+&cpu3 {
+ /*
+ * Although the imx6q fuse indicates that 1.2GHz operation is possible,
+ * the module behaves unstable at this frequency. Hence, remove the
+ * 1.2GHz operation point here.
+ */
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 975000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 1175000
+ >;
+};
+
&ecspi1 {
- cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>, <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
- m25p80@0 {
+ flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,m25p", "jedec,spi-nor";
@@ -396,8 +489,3 @@
*/
status = "disabled";
};
-
-/* The U-Boot: enable usdhc3 for mmc boot */
-&usdhc3 {
- status = "okay";
-};
diff --git a/arch/arm/dts/imx6q-icore-ofcap10.dts b/arch/arm/dts/imx6q-icore-ofcap10.dts
index 81cc346dd14..02aca1e28ce 100644
--- a/arch/arm/dts/imx6q-icore-ofcap10.dts
+++ b/arch/arm/dts/imx6q-icore-ofcap10.dts
@@ -12,6 +12,17 @@
/ {
model = "Engicam i.CoreM6 Quad/Dual OpenFrame Capacitive touch 10.1 Kit";
compatible = "engicam,imx6-icore", "fsl,imx6q";
+
+ panel {
+ compatible = "ampire,am-1280800n3tzqw-t00h";
+ backlight = <&backlight_lvds>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
};
&ldb {
@@ -22,18 +33,11 @@
fsl,data-width = <24>;
status = "okay";
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <60000000>;
- hactive = <1280>;
- vactive = <800>;
- hback-porch = <40>;
- hfront-porch = <40>;
- vback-porch = <10>;
- vfront-porch = <3>;
- hsync-len = <80>;
- vsync-len = <10>;
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
};
};
};
diff --git a/arch/arm/dts/imx6q-logicpd.dts b/arch/arm/dts/imx6q-logicpd.dts
index 45eb0b7f75f..46a4ddedb42 100644
--- a/arch/arm/dts/imx6q-logicpd.dts
+++ b/arch/arm/dts/imx6q-logicpd.dts
@@ -9,11 +9,11 @@
/ {
model = "Logic PD i.MX6QD SOM-M3";
- compatible = "fsl,imx6q";
+ compatible = "logicpd,imx6q-logicpd", "fsl,imx6q";
backlight: backlight-lvds {
compatible = "pwm-backlight";
- pwms = <&pwm3 0 20000>;
+ pwms = <&pwm3 0 20000 0>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
power-supply = <®_lcd>;
@@ -21,6 +21,8 @@
panel-lvds0 {
compatible = "okaya,rs800480t-7x0gp";
+ power-supply = <®_lcd_reset>;
+ backlight = <&backlight>;
port {
panel_in_lvds0: endpoint {
@@ -38,7 +40,6 @@
regulator-max-microvolt = <3300000>;
gpio = <&gpio4 17 GPIO_ACTIVE_HIGH>;
enable-active-high;
- regulator-always-on;
vin-supply = <®_3v3>;
startup-delay-us = <500000>;
};
@@ -52,7 +53,6 @@
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
- regulator-always-on;
vin-supply = <®_lcd>;
};
};
@@ -73,6 +73,16 @@
status = "okay";
};
+&i2c1 {
+ touchscreen@26 {
+ compatible = "ilitek,ili2117";
+ reg = <0x26>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_touchscreen>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
&ldb {
status = "okay";
diff --git a/arch/arm/dts/imx6q-marsboard.dts b/arch/arm/dts/imx6q-marsboard.dts
index 05ee2838822..cc180100239 100644
--- a/arch/arm/dts/imx6q-marsboard.dts
+++ b/arch/arm/dts/imx6q-marsboard.dts
@@ -100,7 +100,7 @@
cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
status = "okay";
- m25p80@0 {
+ flash@0 {
compatible = "microchip,sst25vf016b";
spi-max-frequency = <20000000>;
reg = <0>;
diff --git a/arch/arm/dts/imx6q-mba6.dtsi b/arch/arm/dts/imx6q-mba6.dtsi
index 76e8410f8ed..0d7be456729 100644
--- a/arch/arm/dts/imx6q-mba6.dtsi
+++ b/arch/arm/dts/imx6q-mba6.dtsi
@@ -1,6 +1,16 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&ecspi5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5_mba6x>;
+ cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+};
ðphy {
rxdv-skew-ps = <180>;
@@ -16,3 +26,19 @@
txc-skew-ps = <1860>;
rxc-skew-ps = <1860>;
};
+
+&sata {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi5_mba6x: ecspi5grp-mba6x {
+ fsl,pins = <
+ /* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
+ MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO 0x1b099
+ MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI 0xb099
+ MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK 0xb099
+ MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0xb099 /* eCSPI5 SS0 */
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6q-mba6a.dts b/arch/arm/dts/imx6q-mba6a.dts
index 7983ad94f82..349a08605a5 100644
--- a/arch/arm/dts/imx6q-mba6a.dts
+++ b/arch/arm/dts/imx6q-mba6a.dts
@@ -1,10 +1,13 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
#include "imx6q-tqma6a.dtsi"
#include "imx6qdl-mba6.dtsi"
#include "imx6qdl-mba6a.dtsi"
@@ -12,5 +15,6 @@
/ {
model = "TQ TQMa6Q on MBa6x";
- compatible = "tq,mba6a", "fsl,imx6q";
+ compatible = "tq,imx6q-mba6x-a", "tq,mba6a",
+ "tq,imx6q-tqma6q-a", "fsl,imx6q";
};
diff --git a/arch/arm/dts/imx6q-mba6b.dts b/arch/arm/dts/imx6q-mba6b.dts
index 9d117dd190f..02c9f3e91b8 100644
--- a/arch/arm/dts/imx6q-mba6b.dts
+++ b/arch/arm/dts/imx6q-mba6b.dts
@@ -1,10 +1,13 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
#include "imx6q-tqma6b.dtsi"
#include "imx6qdl-mba6.dtsi"
#include "imx6qdl-mba6b.dtsi"
@@ -12,5 +15,6 @@
/ {
model = "TQ TQMa6Q on MBa6x";
- compatible = "tq,mba6b", "fsl,imx6q";
+ compatible = "tq,imx6q-mba6x-b", "tq,mba6b",
+ "tq,imx6q-tqma6q-b", "fsl,imx6q";
};
diff --git a/arch/arm/dts/imx6q-mccmon6.dts b/arch/arm/dts/imx6q-mccmon6.dts
index 27cde56115f..55692c73943 100644
--- a/arch/arm/dts/imx6q-mccmon6.dts
+++ b/arch/arm/dts/imx6q-mccmon6.dts
@@ -1,31 +1,82 @@
-// SPDX-License-Identifier: GPL-2.0+
+// SPDX-License-Identifier: GPL-2.0-only
/*
- * Copyright 2019
+ * Copyright 2016-2017
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+ or X11
*/
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
+
#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
/ {
- model = "Liebherr Nenzig (LWN) iMX6Q";
- compatible = "lwn,imx6-mccmon6", "fsl,imx6";
+ model = "Liebherr (LWN) monitor6 i.MX6 Quad Board";
+ compatible = "lwn,mccmon6", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x80000000>;
+ };
- aliases {
- mmc0 = &usdhc3;
- mmc1 = &usdhc2;
- spi0 = &ecspi3;
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100 101 102 103 104 105 106 107 108 109
+ 110 111 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127 128 129
+ 130 131 132 133 134 135 136 137 138 139
+ 140 141 142 143 144 145 146 147 148 149
+ 150 151 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167 168 169
+ 170 171 172 173 174 175 176 177 178 179
+ 180 181 182 183 184 185 186 187 188 189
+ 190 191 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207 208 209
+ 210 211 212 213 214 215 216 217 218 219
+ 220 221 222 223 224 225 226 227 228 229
+ 230 231 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247 248 249
+ 250 251 252 253 254 255>;
+ default-brightness-level = <50>;
+ enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
};
- chosen {
- stdout-path = &uart1;
+ reg_lvds: regulator-lvds {
+ compatible = "regulator-fixed";
+ regulator-name = "lvds_ppen";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lvds>;
+ gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
- memory@10000000 {
- reg = <0x10000000 0x80000000>;
+ panel-lvds0 {
+ compatible = "innolux,g121x1-l03";
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
};
};
@@ -33,7 +84,6 @@
cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
- spi-max-frequency = <25000000>;
status = "okay";
s25sl032p: flash@0 {
@@ -50,21 +100,8 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <1>;
- /* KSZ9031 PHY SKEW setup - old values * 60 ps */
- rxc-skew-ps = <1860>;
- txc-skew-ps = <1860>;
- txen-skew-ps = <900>;
- rxdv-skew-ps = <900>;
- rxd0-skew-ps = <180>;
- rxd1-skew-ps = <180>;
- rxd2-skew-ps = <180>;
- rxd3-skew-ps = <180>;
- txd0-skew-ps = <120>;
- txd1-skew-ps = <300>;
- txd2-skew-ps = <0>;
- txd3-skew-ps = <120>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
status = "okay";
};
@@ -181,6 +218,59 @@
};
};
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&weim {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
@@ -201,7 +291,13 @@
&iomuxc {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_backlight: dispgrp {
+ fsl,pins = <
+ /* BLEN_OUT */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
pinctrl_ecspi3: ecspi3grp {
fsl,pins = <
@@ -246,13 +342,6 @@
>;
};
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
@@ -267,6 +356,19 @@
>;
};
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_lvds: reqlvdsgrp {
+ fsl,pins = <
+ /* LVDS_PPEN_OUT */
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
@@ -274,6 +376,15 @@
>;
};
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
@@ -356,27 +467,3 @@
>;
};
};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- bus-width = <4>;
- cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- non-removable;
- no-1-8-v;
- keep-power-in-suspend;
- status = "okay";
-};
diff --git a/arch/arm/dts/imx6q-nitrogen6x.dts b/arch/arm/dts/imx6q-nitrogen6x.dts
index ebb22a404ef..435445a34ad 100644
--- a/arch/arm/dts/imx6q-nitrogen6x.dts
+++ b/arch/arm/dts/imx6q-nitrogen6x.dts
@@ -1,11 +1,11 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2013-2019 Boundary Devices, Inc.
-// Copyright 2012 Freescale Semiconductor, Inc.
-// Copyright 2011 Linaro Ltd.
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2013 Boundary Devices, Inc.
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
/dts-v1/;
-
#include "imx6q.dtsi"
#include "imx6qdl-nitrogen6x.dtsi"
diff --git a/arch/arm/dts/imx6q-novena.dts b/arch/arm/dts/imx6q-novena.dts
index 35383c9a2b1..225cf6b7a7a 100644
--- a/arch/arm/dts/imx6q-novena.dts
+++ b/arch/arm/dts/imx6q-novena.dts
@@ -61,11 +61,6 @@
reg = <0x10000000 0>;
};
- aliases {
- mmc0 = &usdhc3;
- mmc1 = &usdhc2;
- };
-
chosen {
stdout-path = &uart2;
};
@@ -112,7 +107,7 @@
};
panel: panel {
- compatible = "innolux,n133hse-ea1", "simple-panel";
+ compatible = "innolux,n133hse-ea1";
backlight = <&backlight>;
};
@@ -227,20 +222,30 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet_novena>;
phy-mode = "rgmii";
+ phy-handle = <ðphy>;
phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
- rxc-skew-ps = <3000>;
- rxdv-skew-ps = <0>;
- txc-skew-ps = <3000>;
- txen-skew-ps = <0>;
- rxd0-skew-ps = <0>;
- rxd1-skew-ps = <0>;
- rxd2-skew-ps = <0>;
- rxd3-skew-ps = <0>;
- txd0-skew-ps = <3000>;
- txd1-skew-ps = <3000>;
- txd2-skew-ps = <3000>;
- txd3-skew-ps = <3000>;
status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ rxc-skew-ps = <3000>;
+ rxdv-skew-ps = <0>;
+ txc-skew-ps = <3000>;
+ txen-skew-ps = <0>;
+ rxd0-skew-ps = <0>;
+ rxd1-skew-ps = <0>;
+ rxd2-skew-ps = <0>;
+ rxd3-skew-ps = <0>;
+ txd0-skew-ps = <3000>;
+ txd1-skew-ps = <3000>;
+ txd2-skew-ps = <3000>;
+ txd3-skew-ps = <3000>;
+ };
+ };
};
&hdmi {
@@ -460,6 +465,7 @@
};
&pwm1 {
+ #pwm-cells = <2>;
status = "okay";
};
diff --git a/arch/arm/dts/imx6q-phytec-mira-rdk-nand.dts b/arch/arm/dts/imx6q-phytec-mira-rdk-nand.dts
index 65d2e483c13..3f13726c805 100644
--- a/arch/arm/dts/imx6q-phytec-mira-rdk-nand.dts
+++ b/arch/arm/dts/imx6q-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
#include "imx6q.dtsi"
#include "imx6qdl-phytec-phycore-som.dtsi"
#include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
/ {
model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with NAND";
diff --git a/arch/arm/dts/imx6q-pinfunc.h b/arch/arm/dts/imx6q-pinfunc.h
index 9fc6120a185..e40409d04b9 100644
--- a/arch/arm/dts/imx6q-pinfunc.h
+++ b/arch/arm/dts/imx6q-pinfunc.h
@@ -1,10 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Copyright 2013 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
*/
#ifndef __DTS_IMX6Q_PINFUNC_H
@@ -551,6 +547,7 @@
#define MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1e0 0x4f4 0x860 0x2 0x0
#define MX6QDL_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT 0x1e0 0x4f4 0x000 0x4 0x0
#define MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1e0 0x4f4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT 0x1e4 0x4f8 0x000 0x0 0x0
#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1e4 0x4f8 0x848 0x1 0x1
#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1e4 0x4f8 0x868 0x2 0x0
#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1e4 0x4f8 0x000 0x3 0x0
diff --git a/arch/arm/dts/imx6q-sabrelite.dts b/arch/arm/dts/imx6q-sabrelite.dts
index 91e031c7ca8..434b1433e79 100644
--- a/arch/arm/dts/imx6q-sabrelite.dts
+++ b/arch/arm/dts/imx6q-sabrelite.dts
@@ -5,7 +5,6 @@
// Copyright 2011 Linaro Ltd.
/dts-v1/;
-
#include "imx6q.dtsi"
#include "imx6qdl-sabrelite.dtsi"
@@ -17,3 +16,8 @@
&sata {
status = "okay";
};
+
+&ipu1_csi1_from_mipi_vc1 {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+};
diff --git a/arch/arm/dts/imx6q-tbs2910.dts b/arch/arm/dts/imx6q-tbs2910.dts
index 7d0a0676ff7..8daef65d5bb 100644
--- a/arch/arm/dts/imx6q-tbs2910.dts
+++ b/arch/arm/dts/imx6q-tbs2910.dts
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0+ OR MIT
//
-// Copyright 2014-2019 Soeren Moch <smoch@web.de>
+// Copyright 2014 Soeren Moch <smoch@web.de>
/dts-v1/;
@@ -20,7 +20,7 @@
mmc0 = &usdhc2;
mmc1 = &usdhc3;
mmc2 = &usdhc4;
- usb0 = &usbotg;
+ /delete-property/ mmc3;
};
memory@10000000 {
@@ -106,7 +106,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
phy-handle = <&phy>;
status = "okay";
@@ -117,6 +116,8 @@
phy: ethernet-phy@4 {
reg = <4>;
qca,clk-out-frequency = <125000000>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
};
};
};
@@ -158,7 +159,7 @@
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
- rtc: ds1307@68 {
+ rtc: rtc@68 {
compatible = "dallas,ds1307";
reg = <0x68>;
};
diff --git a/arch/arm/dts/imx6q-tqma6a.dtsi b/arch/arm/dts/imx6q-tqma6a.dtsi
index b252077f499..ab4c07c13a1 100644
--- a/arch/arm/dts/imx6q-tqma6a.dtsi
+++ b/arch/arm/dts/imx6q-tqma6a.dtsi
@@ -1,14 +1,16 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
#include "imx6q.dtsi"
#include "imx6qdl-tqma6a.dtsi"
#include "imx6qdl-tqma6.dtsi"
/ {
- memory {
+ memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x40000000>;
};
};
-
diff --git a/arch/arm/dts/imx6q-tqma6b.dtsi b/arch/arm/dts/imx6q-tqma6b.dtsi
index 107a9eb037e..7224c376c31 100644
--- a/arch/arm/dts/imx6q-tqma6b.dtsi
+++ b/arch/arm/dts/imx6q-tqma6b.dtsi
@@ -1,14 +1,15 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ */
#include "imx6q.dtsi"
#include "imx6qdl-tqma6b.dtsi"
#include "imx6qdl-tqma6.dtsi"
/ {
- memory {
+ memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x40000000>;
};
};
-
diff --git a/arch/arm/dts/imx6q.dtsi b/arch/arm/dts/imx6q.dtsi
index c37484dce35..3b77eae40e3 100644
--- a/arch/arm/dts/imx6q.dtsi
+++ b/arch/arm/dts/imx6q.dtsi
@@ -9,7 +9,6 @@
/ {
aliases {
ipu1 = &ipu2;
- video1 = &ipu2;
spi4 = &ecspi5;
};
@@ -50,6 +49,8 @@
arm-supply = <®_arm>;
pu-supply = <®_pu>;
soc-supply = <®_soc>;
+ nvmem-cells = <&cpu_speed_grade>;
+ nvmem-cell-names = "speed_grade";
};
cpu1: cpu@1 {
@@ -74,6 +75,7 @@
396000 1175000
>;
clock-latency = <61036>; /* two CLK32 periods */
+ #cooling-cells = <2>;
clocks = <&clks IMX6QDL_CLK_ARM>,
<&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
<&clks IMX6QDL_CLK_STEP>,
@@ -108,6 +110,7 @@
396000 1175000
>;
clock-latency = <61036>; /* two CLK32 periods */
+ #cooling-cells = <2>;
clocks = <&clks IMX6QDL_CLK_ARM>,
<&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
<&clks IMX6QDL_CLK_STEP>,
@@ -142,6 +145,7 @@
396000 1175000
>;
clock-latency = <61036>; /* two CLK32 periods */
+ #cooling-cells = <2>;
clocks = <&clks IMX6QDL_CLK_ARM>,
<&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
<&clks IMX6QDL_CLK_STEP>,
@@ -155,14 +159,14 @@
};
};
- soc {
+ soc: soc {
ocram: sram@900000 {
compatible = "mmio-sram";
reg = <0x00900000 0x40000>;
clocks = <&clks IMX6QDL_CLK_OCRAM>;
};
- bus@2000000 { /* AIPS1 */
+ aips1: bus@2000000 { /* AIPS1 */
spba-bus@2000000 {
ecspi5: spi@2018000 {
#address-cells = <1>;
@@ -173,15 +177,11 @@
clocks = <&clks IMX6Q_CLK_ECSPI5>,
<&clks IMX6Q_CLK_ECSPI5>;
clock-names = "ipg", "per";
- dmas = <&sdma 11 8 1>, <&sdma 12 8 2>;
+ dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
dma-names = "rx", "tx";
status = "disabled";
};
};
-
- iomuxc: iomuxc@20e0000 {
- compatible = "fsl,imx6q-iomuxc";
- };
};
sata: sata@2200000 {
@@ -406,23 +406,29 @@
&hdmi {
compatible = "fsl,imx6q-hdmi";
- port@2 {
- reg = <2>;
+ ports {
+ port@2 {
+ reg = <2>;
- hdmi_mux_2: endpoint {
- remote-endpoint = <&ipu2_di0_hdmi>;
+ hdmi_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_hdmi>;
+ };
};
- };
- port@3 {
- reg = <3>;
+ port@3 {
+ reg = <3>;
- hdmi_mux_3: endpoint {
- remote-endpoint = <&ipu2_di1_hdmi>;
+ hdmi_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_hdmi>;
+ };
};
};
};
+&iomuxc {
+ compatible = "fsl,imx6q-iomuxc";
+};
+
&ipu1_csi1 {
ipu1_csi1_from_mipi_vc1: endpoint {
remote-endpoint = <&mipi_vc1_to_ipu1_csi1>;
diff --git a/arch/arm/dts/imx6qdl-cubox-i.dtsi b/arch/arm/dts/imx6qdl-cubox-i.dtsi
index e3be453d8a4..1e530d892b7 100644
--- a/arch/arm/dts/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/dts/imx6qdl-cubox-i.dtsi
@@ -55,12 +55,12 @@
pinctrl-0 = <&pinctrl_cubox_i_ir>;
};
- pwmleds {
+ led-controller {
compatible = "pwm-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
- front {
+ led-1 {
active-low;
label = "imx6:red:front";
max-brightness = <248>;
@@ -233,6 +233,7 @@
};
&pwm1 {
+ #pwm-cells = <2>;
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi b/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi
index bf6b3a5ce07..fe72650295a 100644
--- a/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi
+++ b/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi
@@ -5,9 +5,9 @@
*/
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pwm/pwm.h>
-#include <dt-bindings/input/input.h>
/ {
chosen {
@@ -263,6 +263,10 @@
status = "okay";
};
+&usbh1 {
+ disable-over-current;
+};
+
&usdhc2 { /* SD card */
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-dhcom-som.dtsi b/arch/arm/dts/imx6qdl-dhcom-som.dtsi
index 5d10c40313c..5befbe13d1a 100644
--- a/arch/arm/dts/imx6qdl-dhcom-som.dtsi
+++ b/arch/arm/dts/imx6qdl-dhcom-som.dtsi
@@ -132,14 +132,15 @@
#size-cells = <0>;
ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
- compatible = "ethernet-phy-ieee802.3-c22";
+ compatible = "ethernet-phy-id0007.c0f0",
+ "ethernet-phy-ieee802.3-c22";
interrupt-parent = <&gpio4>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
pinctrl-0 = <&pinctrl_ethphy0>;
pinctrl-names = "default";
reg = <0>;
- reset-assert-us = <1000>;
- reset-deassert-us = <1000>;
+ reset-assert-us = <500>;
+ reset-deassert-us = <500>;
reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
smsc,disable-energy-detect; /* Make plugin detection reliable */
};
@@ -728,6 +729,7 @@
pinctrl_usbh1: usbh1-grp {
fsl,pins = <
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x120b0
+ MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b0b1
>;
};
diff --git a/arch/arm/dts/imx6qdl-gw51xx.dtsi b/arch/arm/dts/imx6qdl-gw51xx.dtsi
index 139ffe012dc..069c27fab43 100644
--- a/arch/arm/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/dts/imx6qdl-gw51xx.dtsi
@@ -13,8 +13,8 @@
led0 = &led0;
led1 = &led1;
nand = &gpmi;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -129,8 +129,6 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -452,7 +450,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw52xx.dtsi b/arch/arm/dts/imx6qdl-gw52xx.dtsi
index 1b5c836ff39..b1df2beb283 100644
--- a/arch/arm/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/dts/imx6qdl-gw52xx.dtsi
@@ -13,11 +13,10 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc3;
nand = &gpmi;
ssi0 = &ssi1;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -33,8 +32,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -195,8 +192,6 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -547,7 +542,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw53xx.dtsi b/arch/arm/dts/imx6qdl-gw53xx.dtsi
index e5e9e0c0589..a0710d56276 100644
--- a/arch/arm/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/dts/imx6qdl-gw53xx.dtsi
@@ -13,11 +13,10 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc3;
nand = &gpmi;
ssi0 = &ssi1;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -33,8 +32,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -137,8 +134,7 @@
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-always-on;
};
reg_usb_otg_vbus: regulator-usb-otg-vbus {
@@ -189,8 +185,6 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -545,14 +539,11 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
&usbh1 {
vbus-supply = <®_usb_h1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1>;
status = "okay";
};
@@ -602,7 +593,6 @@
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
>;
};
@@ -723,12 +713,6 @@
>;
};
- pinctrl_usbh1: usbh1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
- >;
- };
-
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
diff --git a/arch/arm/dts/imx6qdl-gw54xx.dtsi b/arch/arm/dts/imx6qdl-gw54xx.dtsi
index 2f41f092142..cda48bf2f16 100644
--- a/arch/arm/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/dts/imx6qdl-gw54xx.dtsi
@@ -14,11 +14,10 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc3;
nand = &gpmi;
ssi0 = &ssi1;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -34,8 +33,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -146,8 +143,7 @@
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-always-on;
};
reg_usb_otg_vbus: regulator@3 {
@@ -226,8 +222,6 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -615,14 +609,11 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
&usbh1 {
vbus-supply = <®_usb_h1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1>;
status = "okay";
};
@@ -680,7 +671,6 @@
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
>;
};
@@ -818,12 +808,6 @@
>;
};
- pinctrl_usbh1: usbh1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
- >;
- };
-
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
diff --git a/arch/arm/dts/imx6qdl-gw551x.dtsi b/arch/arm/dts/imx6qdl-gw551x.dtsi
index c0ffea16d81..435dec6338f 100644
--- a/arch/arm/dts/imx6qdl-gw551x.dtsi
+++ b/arch/arm/dts/imx6qdl-gw551x.dtsi
@@ -57,8 +57,8 @@
led0 = &led0;
nand = &gpmi;
ssi0 = &ssi1;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -67,8 +67,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -536,7 +534,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw552x.dtsi b/arch/arm/dts/imx6qdl-gw552x.dtsi
index b853399aec6..2e61102ae69 100644
--- a/arch/arm/dts/imx6qdl-gw552x.dtsi
+++ b/arch/arm/dts/imx6qdl-gw552x.dtsi
@@ -14,8 +14,8 @@
led1 = &led1;
led2 = &led2;
nand = &gpmi;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -24,8 +24,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -120,15 +118,7 @@
regulator-name = "5P0V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- };
-
- reg_usb_h1_vbus: regulator-usbh1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb_h1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-always-on;
};
};
@@ -399,13 +389,9 @@
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
+ status = "okay"; };
&usbh1 {
- vbus-supply = <®_usb_h1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1>;
status = "okay";
};
@@ -414,7 +400,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
@@ -520,12 +505,6 @@
>;
};
- pinctrl_usbh1: usbh1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
- >;
- };
-
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x13059
diff --git a/arch/arm/dts/imx6qdl-gw553x.dtsi b/arch/arm/dts/imx6qdl-gw553x.dtsi
index b15c2818524..4662408b225 100644
--- a/arch/arm/dts/imx6qdl-gw553x.dtsi
+++ b/arch/arm/dts/imx6qdl-gw553x.dtsi
@@ -55,8 +55,8 @@
led0 = &led0;
led1 = &led1;
nand = &gpmi;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -509,7 +509,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw560x.dtsi b/arch/arm/dts/imx6qdl-gw560x.dtsi
index 6586d877204..4bc4371e6ba 100644
--- a/arch/arm/dts/imx6qdl-gw560x.dtsi
+++ b/arch/arm/dts/imx6qdl-gw560x.dtsi
@@ -55,11 +55,9 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc2;
- mmc1 = &usdhc3;
ssi0 = &ssi1;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -93,8 +91,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -221,8 +217,7 @@
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-always-on;
};
reg_usb_otg_vbus: regulator-usb-otg-vbus {
@@ -280,8 +275,6 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -661,7 +654,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw5903.dtsi b/arch/arm/dts/imx6qdl-gw5903.dtsi
index 1df3faba416..1fdb7ba630f 100644
--- a/arch/arm/dts/imx6qdl-gw5903.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5903.dtsi
@@ -75,8 +75,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -223,9 +221,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -534,7 +529,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "host";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw5904.dtsi b/arch/arm/dts/imx6qdl-gw5904.dtsi
index 381f605cc0d..612b6e068e2 100644
--- a/arch/arm/dts/imx6qdl-gw5904.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5904.dtsi
@@ -55,9 +55,8 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc3;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -73,8 +72,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -176,8 +173,7 @@
regulator-name = "usb_h1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-always-on;
};
reg_usb_otg_vbus: regulator-usb-otg-vbus {
@@ -201,9 +197,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
fixed-link {
@@ -474,6 +467,11 @@
};
};
+ crypto@60 {
+ compatible = "atmel,atecc508a";
+ reg = <0x60>;
+ };
+
imu@6a {
compatible = "st,lsm9ds1-imu";
reg = <0x6a>;
@@ -588,14 +586,11 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
&usbh1 {
vbus-supply = <®_usb_h1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
status = "okay";
};
@@ -756,12 +751,6 @@
>;
};
- pinctrl_usbh1: usbh1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
- >;
- };
-
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
diff --git a/arch/arm/dts/imx6qdl-gw5907.dtsi b/arch/arm/dts/imx6qdl-gw5907.dtsi
index 68585f84d13..fcd3bdfd618 100644
--- a/arch/arm/dts/imx6qdl-gw5907.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5907.dtsi
@@ -13,8 +13,8 @@
led0 = &led0;
led1 = &led1;
nand = &gpmi;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -23,8 +23,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -131,8 +129,6 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -380,7 +376,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "otg";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw5910.dtsi b/arch/arm/dts/imx6qdl-gw5910.dtsi
index 594468dcba8..68e5ab2e27e 100644
--- a/arch/arm/dts/imx6qdl-gw5910.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5910.dtsi
@@ -13,7 +13,6 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc3;
};
chosen {
@@ -27,8 +26,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -146,9 +143,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -402,7 +396,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "host";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-gw5912.dtsi b/arch/arm/dts/imx6qdl-gw5912.dtsi
index f51ec3d62ce..0415bcb4164 100644
--- a/arch/arm/dts/imx6qdl-gw5912.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5912.dtsi
@@ -13,10 +13,9 @@
led0 = &led0;
led1 = &led1;
led2 = &led2;
- mmc0 = &usdhc3;
nand = &gpmi;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -25,8 +24,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -120,8 +117,7 @@
regulator-name = "usb_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
- enable-active-high;
+ regulator-always-on;
};
};
@@ -142,9 +138,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -381,8 +374,6 @@
&usbh1 {
vbus-supply = <®_usb_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1>;
status = "okay";
};
@@ -432,7 +423,6 @@
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
>;
};
@@ -563,12 +553,6 @@
>;
};
- pinctrl_usbh1: usbh1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
- >;
- };
-
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
diff --git a/arch/arm/dts/imx6qdl-gw5913.dtsi b/arch/arm/dts/imx6qdl-gw5913.dtsi
index 44d347f04eb..8e23cec7149 100644
--- a/arch/arm/dts/imx6qdl-gw5913.dtsi
+++ b/arch/arm/dts/imx6qdl-gw5913.dtsi
@@ -13,8 +13,8 @@
led0 = &led0;
led1 = &led1;
nand = &gpmi;
- usb0 = &usbotg;
- usb1 = &usbh1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
};
chosen {
@@ -23,8 +23,6 @@
gpio-keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
user-pb {
label = "user_pb";
@@ -121,9 +119,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <300>;
status = "okay";
};
@@ -346,7 +341,6 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
disable-over-current;
- dr_mode = "host";
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-hummingboard2.dtsi b/arch/arm/dts/imx6qdl-hummingboard2.dtsi
index e4231331f04..eb1ad28946d 100644
--- a/arch/arm/dts/imx6qdl-hummingboard2.dtsi
+++ b/arch/arm/dts/imx6qdl-hummingboard2.dtsi
@@ -203,7 +203,7 @@
&ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hummingboard2_ecspi2>;
- cs-gpios = <&gpio2 26 0>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-icore.dtsi b/arch/arm/dts/imx6qdl-icore.dtsi
index 7814f1ef080..23c318d9636 100644
--- a/arch/arm/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/dts/imx6qdl-icore.dtsi
@@ -150,10 +150,23 @@
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- phy-reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
phy-mode = "rmii";
+ phy-handle = <ð_phy>;
status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ eth_phy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <4000>;
+ reset-deassert-us = <4000>;
+ };
+ };
};
&gpmi {
@@ -232,6 +245,7 @@
};
&pwm3 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "okay";
@@ -384,7 +398,7 @@
pinctrl_usbotg: usbotggrp {
fsl,pins = <
- MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
>;
};
@@ -396,6 +410,7 @@
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17070
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17070
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
diff --git a/arch/arm/dts/imx6qdl-mba6.dtsi b/arch/arm/dts/imx6qdl-mba6.dtsi
index 874b68564a8..78555a61885 100644
--- a/arch/arm/dts/imx6qdl-mba6.dtsi
+++ b/arch/arm/dts/imx6qdl-mba6.dtsi
@@ -1,48 +1,177 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
/ {
aliases {
+ mmc0 = &usdhc3;
mmc1 = &usdhc2;
+ /delete-property/ mmc2;
+ /delete-property/ mmc3;
+ rtc0 = &rtc0;
};
chosen {
- linux,stdout-path = &uart2;
stdout-path = &uart2;
};
- regulators {
- reg_mba6_3p3v: regulator@1 {
- compatible = "regulator-fixed";
- regulator-name = "supply-mba6-3p3v";
- reg = <1>;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
+ beeper: gpio-beeper {
+ compatible = "gpio-beeper";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiobeeper>;
+ gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_buttons: gpio-buttons {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiobuttons>;
+
+ button1 {
+ label = "s6";
+ linux,code = <KEY_F6>;
+ gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
- reg_otgvbus: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_otgpwr>;
- regulator-name = "otg-vbus-supply";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- vin_supply = <®_3p3v>;
+ button2 {
+ label = "s7";
+ linux,code = <KEY_F7>;
+ gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ wakeup-source;
};
+
+ button3 {
+ label = "s8";
+ linux,code = <KEY_F8>;
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioled>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_mba6_3p3v: regulator-mba6-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6-3p3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_pcie: regulator-pcie {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_regpcie>;
+ regulator-name = "supply-pcie";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ /* PCIE.PWR_EN */
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <®_mba6_3p3v>;
+ };
+
+ reg_vcc3v3_audio: regulator-vcc3v3-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3-audio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_mba6_3p3v>;
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ model = "imx-audio-tlv320aic32x4";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&tlv320aic32x4>;
+ audio-asrc = <&asrc>;
+ audio-routing =
+ "IN3_L", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "IN1_L", "Line In Jack",
+ "IN1_R", "Line In Jack",
+ "Line Out Jack", "LOL",
+ "Line Out Jack", "LOR";
+ mux-int-port = <1>;
+ mux-ext-port = <3>;
};
};
+&audmux {
+ status = "okay";
+
+ ssi0 {
+ fsl,audmux-port = <MX31_AUDMUX_PORT1_SSI0>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_SYN |
+ IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(MX31_AUDMUX_PORT3_SSI_PINS_3) |
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(MX31_AUDMUX_PORT3_SSI_PINS_3))
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX31_AUDMUX_PORT3_SSI_PINS_3)
+ >;
+ };
+
+ aud3 {
+ fsl,audmux-port = <MX31_AUDMUX_PORT3_SSI_PINS_3>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(MX31_AUDMUX_PORT1_SSI0)
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_mba6>;
+ cs-gpios = <&gpio3 19 0>, <&gpio3 24 0>;
+};
+
&fec {
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <1>;
- phy-reset-post-delay = <100>;
phy-handle = <ðphy>;
+ mac-address = [00 00 00 00 00 00];
status = "okay";
mdio {
@@ -50,126 +179,63 @@
#size-cells = <0>;
ethphy: ethernet-phy@3 {
- compatible = "ethernet-phy-id0022.1622",
- "ethernet-phy-ieee802.3-c22";
+ compatible = "ethernet-phy-ieee802.3-c22";
reg = <3>;
- force-master;
- max-speed = <1000>;
interrupt-parent = <&gpio1>;
interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <1000>;
+ reset-deassert-us = <100000>;
+ micrel,force-master;
+ max-speed = <1000>;
};
};
};
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
+&i2c1 {
+ tlv320aic32x4: audio-codec@18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "mclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_codec>;
+ ldoin-supply = <®_vcc3v3_audio>;
+ iov-supply = <®_mba6_3p3v>;
+ };
+};
- mba6 {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* FEC phy IRQ */
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x00011008
- /* FEC phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b099
- /* DSE = 100, 100k up, SPEED = MED */
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0xb0a0
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0xb0a0
- /* DSE = 111, pull 100k up */
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0xb038
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0xb038
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0xb038
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0xb038
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0xb038
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0xb038
- /* DSE = 111, pull external */
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x0038
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x0038
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x0038
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x0038
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x0038
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x0038
- /* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0f0
- >;
- };
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio6 7 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x0001b099 /* LCD.PWR_EN */
- MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x0001b099 /* LCD.RESET */
- /* LCD.CONTRAST -> Rev 0100 only, not used on Rev.0200*/
- MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0001b099
-
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b099
- MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b099
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b099
-
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x0001b099
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x0001b099
- MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x0001b099
- MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x0001b099
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x0001b099
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x0001b099
- MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x0001b099
-
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x0001b099
- MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x0001b099
- MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x0001b099
- MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0001b099
- MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x0001b099
-
- MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b099
- MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b099
- MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x0001b099
- MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x0001b099
-
- MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x0001b099
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x0001b099
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x0001b099
-
- MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0001b099
- MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x0001b099
- >;
- };
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
- pinctrl_reg_otgpwr: regotgpwrgrp {
- fsl,pins = <
- /* OTG_PWR */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0001b099
- >;
- };
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b099
- MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b099
- >;
- };
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- /* CLK: 47k Pup SPD_LOW DSE 40Ohm SRE_FAST HYS */
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x00017071
- /* SD2: 47k Pup SPD_LOW DSE 80Ohm SRE_FAST HYS */
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x00017059
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017059
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017059
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017059
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017059
-
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b099 /* usdhc2 CD */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x0001b099 /* usdhc2 WP */
- >;
- };
+&snvs_poweroff {
+ status = "okay";
+};
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x0001b0b0
- MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x00017059
- >;
- };
- };
+&ssi1 {
+ status = "okay";
};
&uart2 {
@@ -178,6 +244,30 @@
status = "okay";
};
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-active-low;
+ rs485-rx-during-tx;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
&usbh1 {
disable-over-current;
status = "okay";
@@ -186,22 +276,260 @@
&usbotg {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
+ power-active-high;
+ over-current-active-low;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
dr_mode = "otg";
- vbus-supply = <®_otgvbus>;
status = "okay";
};
-&usdhc2 { /* Baseboard Slot */
+/* SD card slot */
+&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
vmmc-supply = <®_mba6_3p3v>;
bus-width = <4>;
no-1-8-v;
+ no-mmc;
+ no-sdio;
cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog1>;
+ /* does not work on unmodified starter kit */
+ /* fsl,ext-reset-output; */
status = "okay";
};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0xb099
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0xb099
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0xb099
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0xb099
+ >;
+ };
+
+ pinctrl_codec: codecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0xb0 /* CLK */
+ >;
+ };
+
+ pinctrl_ecspi1_mba6: ecspimba6grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__GPIO3_IO24 0xb099 /* eCSPI1 SS2 */
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ /* FEC phy IRQ */
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x00011008
+ /* FEC phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b099
+ /* DSE = 100, 100k up, SPEED = MED */
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0xb0a0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0xb0a0
+ /* DSE = 111, pull 100k up */
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0xb038
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0xb038
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0xb038
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0xb038
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0xb038
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0xb038
+ /* DSE = 111, pull external */
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x0038
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x0038
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x0038
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x0038
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x0038
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x0038
+ /* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0f0
+ >;
+ };
+
+ pinctrl_gpiobeeper: gpiobeepergrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0xb099
+ >;
+ };
+
+ pinctrl_gpiobuttons: gpiobuttongrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0001b099
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x0001b099
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0001b099
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0xb099 /* LED V15 */
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb099 /* LED V16 */
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0001b099
+
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b099
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b099
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b099
+
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x0001b099
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x0001b099
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x0001b099
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x0001b099
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x0001b099
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x0001b099
+ MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x0001b099
+
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x0001b099
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x0001b099
+ MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x0001b099
+ MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0001b099
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x0001b099
+
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b099
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b099
+ MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x0001b099
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x0001b099
+
+ MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x0001b099
+ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x0001b099
+ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x0001b099
+
+ MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0001b099
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x0001b099
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ /* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x001b0f0 /* #PCIE.WAKE */
+ MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x001b0f0 /* #PCIE.RST */
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x001b0f0 /* #PCIE.DIS */
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ /* 100 k PD, DSE 120 OHM, SPPEED LO */
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x00003050
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ /* 100 k PD, DSE 120 OHM, SPPEED LO */
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x00003050
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ /* 100 k PD, DSE 120 OHM, SPPEED LO */
+ MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x00003050
+ >;
+ };
+
+ pinctrl_regpcie: regpciegrp {
+ fsl,pins = <
+ /* HYS = 1, DSE = 110, PUE+PKE, SPEED = HIGH (11)*/
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x00130f0 /* PCIE.PWR_EN */
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b099
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b099
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CLK__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_CMD__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ /* CLK: 47k Pup SPD_LOW DSE 40Ohm SRE_FAST HYS */
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x00017071
+ /* SD2: 47k Pup SPD_LOW DSE 80Ohm SRE_FAST HYS */
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x00017059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017059
+
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b099 /* usdhc2 CD */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x0001b099 /* usdhc2 WP */
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x0001b0b0
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x00017059
+ MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x0001b099
+ >;
+ };
+
+ pinctrl_wdog1: wdog1grp {
+ fsl,pins = <
+ /* Watchdog out */
+ MX6QDL_PAD_SD1_DAT2__WDOG1_B 0x0000b099
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-mba6a.dtsi b/arch/arm/dts/imx6qdl-mba6a.dtsi
index d8b4d00d853..df8fa169e9f 100644
--- a/arch/arm/dts/imx6qdl-mba6a.dtsi
+++ b/arch/arm/dts/imx6qdl-mba6a.dtsi
@@ -1,39 +1,30 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>, <&pinctrl_enet_fix>;
- interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
- <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
};
&i2c1 {
- sensor1: lm75@49 {
- compatible = "lm75";
+ lm75: temperature-sensor@49 {
+ compatible = "national,lm75";
reg = <0x49>;
};
- eeprom1: m24c64@57 {
- compatible = "st,24c64", "at24";
+ m24c64_57: eeprom@57 {
+ compatible = "atmel,24c64";
reg = <0x57>;
pagesize = <32>;
};
- rtc1: ds1339@68 {
- compatible = "ds1339";
+ rtc0: rtc@68 {
+ compatible = "dallas,ds1339";
reg = <0x68>;
};
};
-
-&iomuxc {
- mba6 {
- pinctrl_enet_fix: enetfixgrp {
- fsl,pins = <
- /* ENET ping patch */
- MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
- >;
- };
- };
-};
diff --git a/arch/arm/dts/imx6qdl-mba6b.dtsi b/arch/arm/dts/imx6qdl-mba6b.dtsi
index 7489b48d82d..7d1cd7454c7 100644
--- a/arch/arm/dts/imx6qdl-mba6b.dtsi
+++ b/arch/arm/dts/imx6qdl-mba6b.dtsi
@@ -1,6 +1,10 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
&fec {
pinctrl-names = "default";
@@ -9,37 +13,37 @@
&i2c1 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_recovery>;
+ scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
};
&i2c3 {
- sensor1: lm75@49 {
- compatible = "lm75";
+ lm75: temperature-sensor@49 {
+ compatible = "national,lm75";
reg = <0x49>;
};
- eeprom1: m24c64@57 {
- compatible = "st,24c64", "at24";
+ m24c64_57: eeprom@57 {
+ compatible = "atmel,24c64";
reg = <0x57>;
pagesize = <32>;
};
- rtc1: ds1339@68 {
- compatible = "ds1339";
+ rtc0: rtc@68 {
+ compatible = "dallas,ds1339";
reg = <0x68>;
};
};
&iomuxc {
- mba6 {
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
- >;
- };
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
+ >;
};
-
};
diff --git a/arch/arm/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/dts/imx6qdl-nitrogen6x.dtsi
index 5094929b6d5..904d5d051d6 100644
--- a/arch/arm/dts/imx6qdl-nitrogen6x.dtsi
+++ b/arch/arm/dts/imx6qdl-nitrogen6x.dtsi
@@ -1,69 +1,692 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2013-2019 Boundary Devices, Inc.
-// Copyright 2012 Freescale Semiconductor, Inc.
-// Copyright 2011 Linaro Ltd.
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2013 Boundary Devices, Inc.
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
-#include "imx6qdl-sabrelite.dtsi"
+/ {
+ chosen {
+ stdout-path = &uart2;
+ };
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
-#undef GP_ENET_PHY_RESET
-#define GP_ENET_PHY_RESET <&gpio1 27 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x030b0
-#define GPIRQ_ENET_PHY <&gpio1 28 IRQ_TYPE_LEVEL_LOW>
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
- >;
- };
-
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* Spare */
- MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b0
- MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x1b0b0
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
- MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
- >;
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_2p5v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 0>;
+ enable-active-high;
+ };
+
+ reg_can_xcvr: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can_xcvr>;
+ gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_wlan_vmmc: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wlan_vmmc>;
+ regulator-name = "reg_wlan_vmmc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ menu {
+ label = "Menu";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ };
+
+ home {
+ label = "Home";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ };
+
+ back {
+ label = "Back";
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ };
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "Volume Down";
+ gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx6q-nitrogen6x-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6q-nitrogen6x-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <3>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ backlight_lvds: backlight-lvds {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ lcd_display: disp0 {
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "bgr666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_j15>;
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ lcd_display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+ };
+
+ panel-lcd {
+ compatible = "okaya,rs800480t-7x0gp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
+
+ panel-lvds0 {
+ compatible = "hannstar,hsd100pxn1";
+ backlight = <&backlight_lvds>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash: flash@0 {
+ compatible = "sst,sst25vf016b", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bootloader";
+ reg = <0x0 0xc0000>;
+ };
+
+ partition@c0000 {
+ label = "env";
+ reg = <0xc0000 0x2000>;
+ };
+
+ partition@c2000 {
+ label = "splash";
+ reg = <0xc2000 0x13e000>;
+ };
};
};
&fec {
-#if 0
- phy-reset-gpios = GP_ENET_PHY_RESET;
-#endif
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ txen-skew-ps = <0>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <0>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <0>;
+ rxd1-skew-ps = <0>;
+ rxd2-skew-ps = <0>;
+ rxd3-skew-ps = <0>;
+ txd0-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd3-skew-ps = <0>;
+ };
+ };
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: sgtl5000@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+
+ rtc: rtc@6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ touchscreen@4 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-source;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6q-nitrogen6x {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_can_xcvr: can-xcvrgrp {
+ fsl,pins = <
+ /* Flexcan XCVR enable */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 /* CS */
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ /* Phy reset */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x000b0
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio-keysgrp {
+ fsl,pins = <
+ /* Power Button */
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ /* Menu Button */
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ /* Home Button */
+ MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+ /* Back Button */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ /* Volume Up Button */
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0
+ /* Volume Down Button */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_j15: j15grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x030b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17071
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10071
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17071
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17071
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17071
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17071
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* CD */
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0 /* CD */
+ >;
+ };
+
+ pinctrl_wlan_vmmc: wlan-vmmcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x100b0
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x000b0
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x000b0
+ MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x000b0
+ >;
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ #pwm-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm4 {
+ #pwm-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
};
-&uart3 {
+&usdhc2 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- uart-has-rtscts;
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ non-removable;
+ vmmc-supply = <®_wlan_vmmc>;
+ cap-power-off-card;
+ keep-power-in-suspend;
status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1271";
+ reg = <2>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = <38400000>;
+ };
};
&usdhc3 {
- /delete-property/ wp-gpios;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-phytec-mira-peb-av-02.dtsi b/arch/arm/dts/imx6qdl-phytec-mira-peb-av-02.dtsi
new file mode 100644
index 00000000000..0020dbb1722
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-phytec-mira-peb-av-02.dtsi
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/ {
+ display: display0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0>;
+ interface-pix-fmt = "rgb24";
+ status = "disabled";
+
+ port@0 {
+ reg = <0>;
+
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ display0_out: endpoint {
+ remote-endpoint = <&peb_panel_lcd_in>;
+ };
+ };
+ };
+
+ panel-lcd {
+ compatible = "edt,etm0700g0edh6";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_pwr>;
+ power-supply = <®_display>;
+ enable-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ backlight = <&backlight>;
+ status = "disabled";
+
+ port {
+ peb_panel_lcd_in: endpoint {
+ remote-endpoint = <&display0_out>;
+ };
+ };
+ };
+
+ reg_display: regulator-peb-display {
+ compatible = "regulator-fixed";
+ regulator-name = "peb-display";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&i2c1 {
+ edt_ft5x06: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_edt_ft5x06>;
+ reg = <0x38>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <2 IRQ_TYPE_NONE>;
+ status = "disabled";
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+ pinctrl_disp0: disp0grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x1b080
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_disp0_pwr: disp0pwrgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+
+ pinctrl_edt_ft5x06: edtft5x06grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0xb0b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi b/arch/arm/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi
new file mode 100644
index 00000000000..037b6019759
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+ status = "disabled";
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+
+ sleep {
+ label = "Sleep Button";
+ gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_SLEEP>;
+ };
+ };
+
+ user_leds: user-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_user_leds>;
+ status = "disabled";
+
+ user-led1 {
+ gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+
+ user-led2 {
+ gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+
+ user-led3 {
+ gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "on";
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl_gpio_keys: gpiokeysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_user_leds: userledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b0
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi b/arch/arm/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
new file mode 100644
index 00000000000..84f884d6e55
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ reg_wl_en: regulator-wl-en {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan_en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wl>;
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ status = "disabled";
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3_bt>;
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+};
+
+&usdhc3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3_wl>;
+ vmmc-supply = <®_wl_en>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ status = "disabled";
+
+ brmcf: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ };
+};
+
+&iomuxc {
+ pinctrl_uart3_bt: uart3grp-bt {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0xb0b1 /* BT ENABLE */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0xb0b1 /* DEV WAKEUP */
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0xb0b1 /* HOST WAKEUP */
+ >;
+ };
+
+ pinctrl_usdhc3_wl: usdhc3grp-wl {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_wl: wlgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0xb0b1 /* WLAN ENABLE */
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/dts/imx6qdl-phytec-mira.dtsi
index 9ebd438dce7..120d6e997a4 100644
--- a/arch/arm/dts/imx6qdl-phytec-mira.dtsi
+++ b/arch/arm/dts/imx6qdl-phytec-mira.dtsi
@@ -145,8 +145,11 @@
};
&i2c1 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
clock-frequency = <400000>;
status = "disabled";
@@ -185,8 +188,11 @@
};
&i2c2 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
clock-frequency = <100000>;
status = "disabled";
};
@@ -218,6 +224,7 @@
};
&pwm1 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
@@ -255,6 +262,7 @@
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
no-1-8-v;
+ disable-wp;
status = "disabled";
};
@@ -298,6 +306,20 @@
>;
};
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x4001b8b1
+ >;
+ };
+
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
@@ -305,10 +327,10 @@
>;
};
- pinctrl_i2c1: i2c1grp {
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
fsl,pins = <
- MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
- MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b1
>;
};
diff --git a/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi
index 77d871340eb..28a80538466 100644
--- a/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi
+++ b/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -78,17 +78,21 @@
};
&i2c3 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ scl-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
clock-frequency = <400000>;
status = "okay";
eeprom@50 {
- compatible = "atmel,24c32";
+ compatible = "st,24c32", "atmel,24c32";
+ pagesize = <32>;
reg = <0x50>;
};
- pmic@58 {
+ pmic: pmic@58 {
compatible = "dlg,da9062";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pmic>;
@@ -96,6 +100,8 @@
interrupt-parent = <&gpio1>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
da9062_rtc: rtc {
compatible = "dlg,da9062-rtc";
@@ -107,6 +113,17 @@
watchdog {
compatible = "dlg,da9062-watchdog";
+ dlg,use-sw-pm;
+ };
+
+ thermal {
+ compatible = "dlg,da9062-thermal";
+ status = "disabled";
+ };
+
+ gpio {
+ compatible = "dlg,da9062-gpio";
+ status = "disabled";
};
regulators {
@@ -255,6 +272,13 @@
>;
};
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b8b1
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
+ >;
+ };
+
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
diff --git a/arch/arm/dts/imx6qdl-pico.dtsi b/arch/arm/dts/imx6qdl-pico.dtsi
index 50379d04b70..f7a56d6b160 100644
--- a/arch/arm/dts/imx6qdl-pico.dtsi
+++ b/arch/arm/dts/imx6qdl-pico.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0 OR MIT
//
// Copyright 2018 Technexion Ltd.
//
@@ -9,11 +9,6 @@
#include <dt-bindings/gpio/gpio.h>
/ {
- aliases {
- mmc0 = &usdhc3;
- usb0 = &usbotg;
- };
-
chosen {
stdout-path = &uart1;
};
@@ -42,6 +37,22 @@
regulator-always-on;
};
+ reg_1p5v: regulator-1p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P5V";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ reg_2p8v: regulator-2p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
reg_usb_otg_vbus: regulator-usb-otg-vbus {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg_vbus>;
@@ -51,6 +62,81 @@
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
};
+
+ codec_osc: clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-sgtl5000";
+ model = "imx6-pico-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <3>;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 50000 0>;
+ brightness-levels = <0 36 72 108 144 180 216 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ reg_lcd_3v3: regulator-lcd-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lcd>;
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ lcd_display: disp0 {
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1>;
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ lcd_display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
+ };
+
+ panel {
+ compatible = "vxt,vl050-8048nt-c01";
+ backlight = <&backlight>;
+ power-supply = <®_lcd_3v3>;
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
+ };
};
&audmux {
@@ -81,7 +167,7 @@
&ecspi2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
- cs-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
status = "okay";
};
@@ -90,7 +176,18 @@
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+ phy-handle = <&phy>;
status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy: ethernet-phy@1 {
+ reg = <1>;
+ qca,clk-out-frequency = <125000000>;
+ };
+ };
};
&hdmi {
@@ -102,6 +199,15 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
+
+ sgtl5000: audio-codec@a {
+ #sound-dai-cells = <0>;
+ reg = <0x0a>;
+ compatible = "fsl,sgtl5000";
+ clocks = <&codec_osc>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_1p8v>;
+ };
};
&i2c2 {
@@ -109,6 +215,40 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio5 27 GPIO_ACTIVE_LOW>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ wakeup-source;
+ };
+
+ camera@3c {
+ compatible = "ovti,ov5645";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5645>;
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO2>;
+ clock-names = "xclk";
+ clock-frequency = <24000000>;
+ vdddo-supply = <®_1p8v>;
+ vdda-supply = <®_2p8v>;
+ vddd-supply = <®_1p5v>;
+ enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+
+ port {
+ ov5645_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
};
&i2c3 {
@@ -117,11 +257,28 @@
status = "okay";
};
+&ipu1_di0_disp0 {
+ remote-endpoint = <&lcd_display_in>;
+};
+
+&mipi_csi {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&ov5645_to_mipi_csi2>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+};
+
&pcie {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pcie_reset>;
reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>;
- status = "okay";
};
&pwm1 {
@@ -161,14 +318,14 @@
&uart2 { /* Bluetooth module */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
status = "okay";
};
@@ -219,7 +376,6 @@
pinctrl_hog: hoggrp {
fsl,pins = <
MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x4001b0b5 /* PICO_P24 */
- MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x4001b0b5 /* PICO_P25 */
MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x4001b0b5 /* PICO_P26 */
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x4001b0b5 /* PICO_P28 */
MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x4001b0b5 /* PICO_P30 */
@@ -316,6 +472,48 @@
>;
};
+ pinctrl_ipu1: ipu1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_ov5645: ov5645grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x0b0b0
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0b0b0
+ MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x000b0
+ >;
+ };
+
pinctrl_pcie_reset: pciegrp {
fsl,pins = <
MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x130b0
@@ -346,6 +544,12 @@
>;
};
+ pinctrl_reg_lcd: reglcdgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
diff --git a/arch/arm/dts/imx6qdl-sabreauto.dtsi b/arch/arm/dts/imx6qdl-sabreauto.dtsi
index 28a7fdb0f1e..1368a476203 100644
--- a/arch/arm/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/dts/imx6qdl-sabreauto.dtsi
@@ -12,6 +12,7 @@
};
memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x80000000>;
};
@@ -75,39 +76,49 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ reg_audio: regulator-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "cs42888_supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
- reg_audio: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "cs42888_supply";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ reg_usb_h1_vbus: regulator-usb-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&max7310_b 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_usb_h1_vbus: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "usb_h1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&max7310_b 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_usb_otg_vbus: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "usb_otg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&max7310_c 1 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&max7310_c 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_can_en: regulator-can-en {
+ compatible = "regulator-fixed";
+ regulator-name = "can-en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&max7310_b 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_can_stby: regulator-can-stby {
+ compatible = "regulator-fixed";
+ regulator-name = "can-stby";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&max7310_b 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_can_en>;
};
sound-cs42888 {
@@ -219,6 +230,8 @@
accelerometer@1c {
compatible = "fsl,mma8451";
reg = <0x1c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mma8451_int>;
interrupt-parent = <&gpio6>;
interrupts = <31 IRQ_TYPE_LEVEL_LOW>;
};
@@ -254,12 +267,12 @@
};
&ecspi1 {
- cs-gpios = <&gpio3 19 0>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
status = "disabled"; /* pin conflict with WEIM NOR */
- flash: m25p80@0 {
+ flash: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,m25p32", "jedec,spi-nor";
@@ -285,6 +298,21 @@
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
fsl,err006687-workaround-present;
+ fsl,magic-packet;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can_stby>;
+ status = "disabled"; /* pin conflict with fec */
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can_stby>;
status = "okay";
};
@@ -503,6 +531,20 @@
>;
};
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x17059
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x17059
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x17059
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x17059
+ >;
+ };
+
pinctrl_gpio_keys: gpiokeysgrp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x1b0b0
@@ -589,6 +631,12 @@
>;
};
+ pinctrl_mma8451_int: mma8451intgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1
+ >;
+ };
+
pinctrl_pwm3: pwm1grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
@@ -753,11 +801,16 @@
};
&pwm3 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "okay";
};
+&pcie {
+ status = "okay";
+};
+
&spdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spdif>;
diff --git a/arch/arm/dts/imx6qdl-sabrelite.dtsi b/arch/arm/dts/imx6qdl-sabrelite.dtsi
index 673a19c3df4..a757817a3c2 100644
--- a/arch/arm/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/dts/imx6qdl-sabrelite.dtsi
@@ -8,336 +8,683 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x000b1
-#define GP_ECSPI1_NOR_CS <&gpio3 19 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x0b0b1
- >;
+/ {
+ chosen {
+ stdout-path = &uart2;
};
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
-#undef GP_ENET_PHY_RESET
-#define GP_ENET_PHY_RESET <&gpio3 23 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x030b0
-#define GPIRQ_ENET_PHY <&gpio1 28 IRQ_TYPE_LEVEL_LOW>
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
- >;
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x40000000>;
};
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* Spare */
- MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x1b0b0
- >;
- };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_2p5v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
- MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
- >;
- };
+ reg_3p3v: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
- pinctrl_i2c1_1: i2c1-1grp {
- fsl,pins = <
-#define GP_I2C1_SCL <&gpio3 21 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x4001b8b1
-#define GP_I2C1_SDA <&gpio3 28 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x4001b8b1
- >;
- };
+ reg_usb_otg_vbus: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 0>;
+ enable-active-high;
+ };
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
- MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
- >;
- };
+ reg_can_xcvr: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can_xcvr>;
+ gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ };
- pinctrl_i2c2_1: i2c2-1grp {
- fsl,pins = <
-#define GP_I2C2_SCL <&gpio4 12 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b1
-#define GP_I2C2_SDA <&gpio4 13 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b1
- >;
- };
+ reg_1p5v: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "1P5V";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
-#define GPIRQ_I2C3_J7 <&gpio1 9 IRQ_TYPE_EDGE_FALLING>
-#define GP_I2C3_J7 <&gpio1 9 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
- >;
- };
+ reg_1p8v: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- pinctrl_i2c3_1: i2c3-1grp {
- fsl,pins = <
-#define GP_I2C3_SCL <&gpio1 5 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
-#define GP_I2C3_SDA <&gpio7 11 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
- >;
- };
+ reg_2p8v: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "2P8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
- >;
+ reg_usb_h1_vbus: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
};
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
- >;
+ mipi_xclk: mipi_xclk {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <22000000>;
+ clock-output-names = "mipi_pwm3";
+ pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
+ status = "okay";
};
- pinctrl_pwm4: pwm4grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
- >;
- };
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ menu {
+ label = "Menu";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ };
+
+ home {
+ label = "Home";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ };
- pinctrl_reg_usbotg_vbus: reg-usbotg-vbusgrp {
- fsl,pins = <
-#define GP_REG_USBOTG <&gpio3 22 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x030b0
- >;
+ back {
+ label = "Back";
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ };
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "Volume Down";
+ gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
};
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
- >;
+ sound {
+ compatible = "fsl,imx6q-sabrelite-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6q-sabrelite-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
};
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
- >;
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_3p3v>;
+ status = "okay";
};
- pinctrl_usbh1: usbh1grp {
- fsl,pins = <
-#define GP_USBH1_HUB_RESET <&gpio7 12 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0b0b0
- >;
+ backlight_lvds: backlight-lvds {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_3p3v>;
+ status = "okay";
};
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
- MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
- >;
+ lcd_display: disp0 {
+ compatible = "fsl,imx-parallel-display";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interface-pix-fmt = "bgr666";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_j15>;
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ lcd_display_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lcd_display_out: endpoint {
+ remote-endpoint = <&lcd_panel_in>;
+ };
+ };
};
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
-#define GP_USDHC3_CD <&gpio7 0 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
-#define GP_USDHC3_WP <&gpio7 1 GPIO_ACTIVE_HIGH>
- MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b0
- >;
+ panel-lcd {
+ compatible = "okaya,rs800480t-7x0gp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ lcd_panel_in: endpoint {
+ remote-endpoint = <&lcd_display_out>;
+ };
+ };
};
- pinctrl_usdhc4: usdhc4grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
- MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
- MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
- MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
- MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
- MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
-#define GP_USDHC4_CD <&gpio2 6 GPIO_ACTIVE_LOW>
- MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0
- >;
+ panel-lvds0 {
+ compatible = "hannstar,hsd100pxn1";
+ backlight = <&backlight_lvds>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
};
};
-/ {
- aliases {
- mmc0 = &usdhc3;
- mmc1 = &usdhc4;
- pwm_lcd = &pwm1;
- pwm_lvds = &pwm4;
- };
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+ data-shift = <12>; /* Lines 19:12 used */
+ hsync-active = <1>;
+ vync-active = <1>;
+};
- chosen {
- stdout-path = &uart2;
- };
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
- memory {
- reg = <0x10000000 0x40000000>;
- };
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
- reg_3p3v: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3P3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
- reg_usb_otg_vbus: regulator-usb-otg-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb_otg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = GP_REG_USBOTG;
- enable-active-high;
- };
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ xceiver-supply = <®_can_xcvr>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
};
&ecspi1 {
- cs-gpios = GP_ECSPI1_NOR_CS;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
- flash: m25p80@0 {
+ flash: flash@0 {
compatible = "sst,sst25vf016b", "jedec,spi-nor";
spi-max-frequency = <20000000>;
reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- mtd@00000000 {
- label = "U-Boot";
- reg = <0x0 0xC0000>;
- };
-
- mtd@000C0000 {
- label = "env";
- reg = <0xC0000 0x2000>;
- };
- mtd@000C2000 {
- label = "splash";
- reg = <0xC2000 0x13e000>;
- };
};
};
&fec {
- phy-handle = <ðphy>;
- phy-mode = "rgmii";
-#if 0
- phy-reset-gpios = GP_ENET_PHY_RESET;
-#endif
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
- rxc-skew-ps = <3000>;
- rxd0-skew-ps = <0>;
- rxd1-skew-ps = <0>;
- rxd2-skew-ps = <0>;
- rxd3-skew-ps = <0>;
- rxdv-skew-ps = <0>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
status = "okay";
- txc-skew-ps = <3000>;
- txd0-skew-ps = <0>;
- txd1-skew-ps = <0>;
- txd2-skew-ps = <0>;
- txd3-skew-ps = <0>;
- txen-skew-ps = <0>;
mdio {
- #address-cells = <0>;
- #size-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
ethphy: ethernet-phy {
- interrupts-extended = GPIRQ_ENET_PHY;
+ compatible = "ethernet-phy-ieee802.3-c22";
+ txen-skew-ps = <0>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <0>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <0>;
+ rxd1-skew-ps = <0>;
+ rxd2-skew-ps = <0>;
+ rxd3-skew-ps = <0>;
+ txd0-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd3-skew-ps = <0>;
};
};
};
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
&i2c1 {
clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
+ pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
- pinctrl-1 = <&pinctrl_i2c1_1>;
- scl-gpios = GP_I2C1_SCL;
- sda-gpios = GP_I2C1_SDA;
status = "okay";
+
+ codec: sgtl5000@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
};
&i2c2 {
clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
+ pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
- pinctrl-1 = <&pinctrl_i2c2_1>;
- scl-gpios = GP_I2C2_SCL;
- sda-gpios = GP_I2C2_SDA;
status = "okay";
- hdmi_edid: edid@50 {
- compatible = "fsl,imx6-hdmi-i2c";
- reg = <0x50>;
+ ov5640: camera@40 {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x40>;
+ clocks = <&mipi_xclk>;
+ clock-names = "xclk";
+ DOVDD-supply = <®_1p8v>;
+ AVDD-supply = <®_2p8v>;
+ DVDD-supply = <®_1p5v>;
+ reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
+ powerdown-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
+
+ port {
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+
+ ov5642: camera@42 {
+ compatible = "ovti,ov5642";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5642>;
+ clocks = <&clks IMX6QDL_CLK_CKO2>;
+ clock-names = "xclk";
+ reg = <0x42>;
+ reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+
+ port {
+ ov5642_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
};
};
&i2c3 {
clock-frequency = <100000>;
- pinctrl-names = "default", "gpio";
+ pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
- pinctrl-1 = <&pinctrl_i2c3_1>;
- scl-gpios = GP_I2C3_SCL;
- sda-gpios = GP_I2C3_SDA;
status = "okay";
};
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6q-sabrelite {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* SGTL5000 sys_mclk */
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0
+ MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0
+ MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
+ MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_can_xcvr: can-xcvrgrp {
+ fsl,pins = <
+ /* Flexcan XCVR enable */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 /* CS */
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ /* Phy reset */
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x000b0
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio-keysgrp {
+ fsl,pins = <
+ /* Power Button */
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ /* Menu Button */
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ /* Home Button */
+ MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+ /* Back Button */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ /* Volume Up Button */
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0
+ /* Volume Down Button */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
+ MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
+ >;
+ };
+
+ pinctrl_j15: j15grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
+
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x000b0
+ MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
+ >;
+ };
+
+ pinctrl_ov5642: ov5642grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x130b0
+ MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x000b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x030b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* CD */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0 /* WP */
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0 /* CD */
+ >;
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
&pcie {
status = "okay";
};
&pwm1 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&pwm3 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "okay";
};
&pwm4 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm4>;
status = "okay";
};
+&ssi1 {
+ status = "okay";
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
@@ -351,10 +698,7 @@
};
&usbh1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1>;
- disable-over-current;
- reset-gpios = GP_USBH1_HUB_RESET;
+ vbus-supply = <®_usb_h1_vbus>;
status = "okay";
};
@@ -369,8 +713,8 @@
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
- cd-gpios = GP_USDHC3_CD;
- wp-gpios = GP_USDHC3_WP;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
vmmc-supply = <®_3p3v>;
status = "okay";
};
@@ -378,7 +722,21 @@
&usdhc4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc4>;
- cd-gpios = GP_USDHC4_CD;
+ cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
vmmc-supply = <®_3p3v>;
status = "okay";
};
+
+&mipi_csi {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&ov5640_to_mipi_csi2>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-sabresd.dtsi b/arch/arm/dts/imx6qdl-sabresd.dtsi
index eddb3901745..37482a9023f 100644
--- a/arch/arm/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/dts/imx6qdl-sabresd.dtsi
@@ -8,64 +8,62 @@
#include <dt-bindings/input/input.h>
/ {
- aliases {
- mmc1 = &usdhc3;
- };
-
chosen {
stdout-path = &uart1;
};
memory@10000000 {
+ device_type = "memory";
reg = <0x10000000 0x40000000>;
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_usb_otg_vbus: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "usb_otg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
+ reg_usb_h1_vbus: regulator-usb-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
- reg_usb_h1_vbus: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "usb_h1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 29 0>;
- enable-active-high;
- vin-supply = <&swbst_reg>;
- };
-
- reg_audio: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "wm8962-supply";
- gpio = <&gpio4 10 0>;
- enable-active-high;
- };
-
- reg_pcie: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pcie_reg>;
- regulator-name = "MPCIE_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio3 19 0>;
- enable-active-high;
- };
+ reg_audio: regulator-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply";
+ gpio = <&gpio4 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_pcie: regulator-pcie {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_reg>;
+ regulator-name = "MPCIE_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_sensors: regulator-sensors {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sensors_reg>;
+ regulator-name = "sensors-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
gpio-keys {
@@ -99,17 +97,24 @@
compatible = "fsl,imx6q-sabresd-wm8962",
"fsl,imx-audio-wm8962";
model = "wm8962-audio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hp>;
ssi-controller = <&ssi2>;
audio-codec = <&codec>;
+ audio-asrc = <&asrc>;
audio-routing =
"Headphone Jack", "HPOUTL",
"Headphone Jack", "HPOUTR",
"Ext Spk", "SPKOUTL",
"Ext Spk", "SPKOUTR",
"AMIC", "MICBIAS",
- "IN3R", "AMIC";
+ "IN3R", "AMIC",
+ "DMIC", "MICBIAS",
+ "DMICDAT", "DMIC";
mux-int-port = <2>;
mux-ext-port = <3>;
+ hp-det-gpio = <&gpio7 8 GPIO_ACTIVE_LOW>;
+ mic-det-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
};
backlight_lvds: backlight-lvds {
@@ -187,12 +192,12 @@
};
&ecspi1 {
- cs-gpios = <&gpio4 9 0>;
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
- flash: m25p80@0 {
+ flash: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,m25p32", "jedec,spi-nor";
@@ -205,8 +210,21 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
- phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ phy-handle = <&phy>;
+ fsl,magic-packet;
status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy: ethernet-phy@1 {
+ reg = <1>;
+ qca,clk-out-frequency = <125000000>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ };
+ };
};
&hdmi {
@@ -244,6 +262,17 @@
>;
};
+ accelerometer@1c {
+ compatible = "fsl,mma8451";
+ reg = <0x1c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_mma8451_int>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+ vdd-supply = <®_sensors>;
+ vddio-supply = <®_sensors>;
+ };
+
ov5642: camera@3c {
compatible = "ovti,ov5642";
pinctrl-names = "default";
@@ -276,6 +305,16 @@
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
+ touchscreen@4 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2_egalax_int>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+ };
+
ov5640: camera@3c {
compatible = "ovti,ov5640";
pinctrl-names = "default";
@@ -414,6 +453,27 @@
interrupts = <7 2>;
wakeup-gpios = <&gpio6 7 0>;
};
+
+ magnetometer@e {
+ compatible = "fsl,mag3110";
+ reg = <0x0e>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3_mag3110_int>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+ vdd-supply = <®_sensors>;
+ vddio-supply = <®_sensors>;
+ };
+
+ light-sensor@44 {
+ compatible = "isil,isl29023";
+ reg = <0x44>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3_isl29023_int>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ vcc-supply = <®_sensors>;
+ };
};
&iomuxc {
@@ -488,6 +548,13 @@
>;
};
+ pinctrl_hp: hpgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
@@ -495,6 +562,12 @@
>;
};
+ pinctrl_i2c1_mma8451_int: i2c1mma8451intgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0xb0b1
+ >;
+ };
+
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
@@ -502,6 +575,12 @@
>;
};
+ pinctrl_i2c2_egalax_int: i2c2egalaxintgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x1b0b0
+ >;
+ };
+
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
@@ -509,6 +588,18 @@
>;
};
+ pinctrl_i2c3_isl29023_int: i2c3isl29023intgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c3_mag3110_int: i2c3mag3110intgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__GPIO3_IO16 0xb0b1
+ >;
+ };
+
pinctrl_ipu1_csi0: ipu1csi0grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
@@ -557,6 +648,12 @@
>;
};
+ pinctrl_sensors_reg: sensorsreggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1b0b0
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
@@ -658,6 +755,7 @@
};
&pwm1 {
+ #pwm-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
@@ -675,10 +773,22 @@
vin-supply = <&sw1c_reg>;
};
+®_vdd1p1 {
+ vin-supply = <&vgen5_reg>;
+};
+
+®_vdd2p5 {
+ vin-supply = <&vgen5_reg>;
+};
+
&snvs_poweroff {
status = "okay";
};
+&snvs_pwrkey {
+ status = "okay";
+};
+
&ssi2 {
status = "okay";
};
diff --git a/arch/arm/dts/imx6qdl-sr-som-ti.dtsi b/arch/arm/dts/imx6qdl-sr-som-ti.dtsi
index 44a97ba93a9..352ac585ca6 100644
--- a/arch/arm/dts/imx6qdl-sr-som-ti.dtsi
+++ b/arch/arm/dts/imx6qdl-sr-som-ti.dtsi
@@ -153,6 +153,7 @@
bus-width = <4>;
keep-power-in-suspend;
mmc-pwrseq = <&pwrseq_ti_wifi>;
+ cap-power-off-card;
non-removable;
vmmc-supply = <&vcc_3v3>;
/* vqmmc-supply = <&nvcc_sd1>; - MMC layer doesn't like it! */
diff --git a/arch/arm/dts/imx6qdl-sr-som.dtsi b/arch/arm/dts/imx6qdl-sr-som.dtsi
index c20bed27219..ce543e325cd 100644
--- a/arch/arm/dts/imx6qdl-sr-som.dtsi
+++ b/arch/arm/dts/imx6qdl-sr-som.dtsi
@@ -53,7 +53,6 @@
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
- phy-handle = <&phy>;
phy-mode = "rgmii-id";
/*
@@ -69,16 +68,30 @@
#address-cells = <1>;
#size-cells = <0>;
- phy: ethernet-phy@0 {
- /*
- * The PHY can appear either:
- * - AR8035: at address 0 or 4
- * - ADIN1300: at address 1
- * Actual address being detected at runtime.
- */
- reg = <0xffffffff>;
+ /*
+ * The PHY can appear at either address 0 or 4 due to the
+ * configuration (LED) pin not being pulled sufficiently.
+ */
+ ethernet-phy@0 {
+ reg = <0>;
qca,clk-out-frequency = <125000000>;
+ qca,smarteee-tw-us-1g = <24>;
+ };
+
+ ethernet-phy@4 {
+ reg = <4>;
+ qca,clk-out-frequency = <125000000>;
+ qca,smarteee-tw-us-1g = <24>;
+ };
+
+ /*
+ * ADIN1300 (som rev 1.9 or later) is always at address 1. It
+ * will be enabled automatically by U-Boot if detected.
+ */
+ ethernet-phy@1 {
+ reg = <1>;
adi,phy-output-clock = "125mhz-free-running";
+ status = "disabled";
};
};
};
diff --git a/arch/arm/dts/imx6qdl-tqma6.dtsi b/arch/arm/dts/imx6qdl-tqma6.dtsi
index 85eb3d8da17..344ea935c7d 100644
--- a/arch/arm/dts/imx6qdl-tqma6.dtsi
+++ b/arch/arm/dts/imx6qdl-tqma6.dtsi
@@ -1,40 +1,30 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
-/ {
- aliases {
- mmc0 = &usdhc3;
- /delete-property/ mmc1;
- /delete-property/ mmc2;
- };
-
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
- reg_3p3v: regulator@0 {
- compatible = "regulator-fixed";
- regulator-name = "supply-3p3v";
- reg = <0>;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+/ {
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-3p3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
};
&ecspi1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
- fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio3 19 0>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
status = "okay";
- flash: m25p80@0 {
- status = "okay";
- compatible = "micron,n25q128a13", "n25q128a13";
+ m25p80: flash@0 {
+ compatible = "jedec,spi-nor";
spi-max-frequency = <50000000>;
reg = <0>;
#address-cells = <1>;
@@ -44,151 +34,163 @@
};
&iomuxc {
- tqma6 {
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- /* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b099
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0xb099
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0xb099
- /* eCSPI1 SS1 */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0xb099
- >;
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ /* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b099
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0xb099
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0xb099
+ /* eCSPI1 SS1 */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0xb099
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
+ >;
+ };
+
+ pinctrl_i2c1_recovery: i2c1recoverygrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x4001b899
+ MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x4001b899
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b899
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
+ >;
+ };
+
+ pinctrl_i2c3_recovery: i2c3recoverygrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b899
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b899
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b099 /* PMIC irq */
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ >;
+ };
+};
+
+&pmic {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_vddcore: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
};
- pinctrl_i2c1_tqma6: i2c1-tqma6grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
- >;
+ reg_vddsoc: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
};
- pinctrl_i2c3_tqma6: i2c3-tqma6grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b899
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
- >;
+ reg_gen_3v3: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
};
- pinctrl_pmic: pmicgrp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b099 /* PMIC irq */
- >;
+ reg_ddr_1v5a: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
};
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
- >;
+ reg_ddr_1v5b: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
};
- };
-};
-&pmic {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pmic>;
- interrupt-parent = <&gpio6>;
- interrupts = <10 8>;
-
- regulators {
- reg_vddcore: sw1ab {
- regulator-min-microvolt = <300000>;
- regulator-max-microvolt = <1875000>;
- regulator-always-on;
- };
-
- reg_vddsoc: sw1c {
- regulator-min-microvolt = <300000>;
- regulator-max-microvolt = <1875000>;
- regulator-always-on;
- };
-
- reg_gen_3v3: sw2 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_ddr_1v5a: sw3a {
- regulator-min-microvolt = <400000>;
- regulator-max-microvolt = <1975000>;
- regulator-always-on;
- };
-
- reg_ddr_1v5b: sw3b {
- regulator-min-microvolt = <400000>;
- regulator-max-microvolt = <1975000>;
- regulator-always-on;
- };
-
- sw4_reg: sw4 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_5v_600mA: swbst {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5150000>;
- regulator-always-on;
- };
-
- reg_snvs_3v: vsnvs {
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- };
-
- reg_vrefddr: vrefddr {
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_vgen1_1v5: vgen1 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1550000>;
- /* not used */
- };
-
- reg_vgen2_1v2_eth: vgen2 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1550000>;
- regulator-always-on;
- };
-
- reg_vgen3_2v8: vgen3 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_vgen4_1v8: vgen4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_vgen5_1v8_eth: vgen5 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_vgen6_3v3: vgen6 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5v_600mA: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ regulator-always-on;
+ };
+
+ reg_snvs_3v: vsnvs {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ reg_vrefddr: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vgen1_1v5: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ /* not used */
+ };
+
+ reg_vgen2_1v2_eth: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
};
+
+ reg_vgen3_2v8: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vgen4_1v8: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vgen5_1v8_eth: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vgen6_3v3: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
};
/* eMMC */
@@ -198,6 +200,8 @@
vmmc-supply = <®_3p3v>;
non-removable;
disable-wp;
+ no-sd;
+ no-sdio;
bus-width = <8>;
#address-cells = <1>;
#size-cells = <0>;
diff --git a/arch/arm/dts/imx6qdl-tqma6a.dtsi b/arch/arm/dts/imx6qdl-tqma6a.dtsi
index f94a5d80c2c..7dc3f0005b0 100644
--- a/arch/arm/dts/imx6qdl-tqma6a.dtsi
+++ b/arch/arm/dts/imx6qdl-tqma6a.dtsi
@@ -1,27 +1,53 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+&fec {
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,err006687-workaround-present;
+};
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1_tqma6>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_recovery>;
+ scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
clock-frequency = <100000>;
status = "okay";
- pmic: pf0100@08 {
+ pmic: pmic@8 {
compatible = "fsl,pfuze100";
reg = <0x08>;
};
- sensor0: lm75@48 {
- compatible = "lm75";
+ sensor@48 {
+ compatible = "national,lm75";
reg = <0x48>;
};
- eeprom0: m24c64@50 {
- compatible = "st,24c64", "at24";
+ eeprom@50 {
+ compatible = "st,24c64", "atmel,24c64";
reg = <0x50>;
pagesize = <32>;
};
};
+&iomuxc {
+ /*
+ * This pinmuxing is required for the ERR006687 workaround. Board
+ * DTS files that enable the FEC controller with
+ * fsl,err006687-workaround-present must include this group.
+ */
+ pinctrl_enet_fix: enetfixgrp {
+ fsl,pins = <
+ /* ENET ping patch */
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ >;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-tqma6b.dtsi b/arch/arm/dts/imx6qdl-tqma6b.dtsi
index 682f5537012..dd092576644 100644
--- a/arch/arm/dts/imx6qdl-tqma6b.dtsi
+++ b/arch/arm/dts/imx6qdl-tqma6b.dtsi
@@ -1,27 +1,33 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright (C) 2020 TQ-Systems GmbH
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
&i2c3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3_tqma6>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_recovery>;
+ scl-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
clock-frequency = <100000>;
status = "okay";
- pmic: pf0100@08 {
+ pmic: pmic@8 {
compatible = "fsl,pfuze100";
reg = <0x08>;
};
- sensor0: lm75@48 {
- compatible = "lm75";
+ sensor@48 {
+ compatible = "national,lm75";
reg = <0x48>;
};
- eeprom0: m24c64@50 {
- compatible = "st,24c64", "at24";
+ eeprom@50 {
+ compatible = "st,24c64", "atmel,24c64";
reg = <0x50>;
pagesize = <32>;
};
};
-
diff --git a/arch/arm/dts/imx6qdl-udoo.dtsi b/arch/arm/dts/imx6qdl-udoo.dtsi
index 2d0d102661b..93a8123da27 100644
--- a/arch/arm/dts/imx6qdl-udoo.dtsi
+++ b/arch/arm/dts/imx6qdl-udoo.dtsi
@@ -4,7 +4,9 @@
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*/
+
#include <dt-bindings/gpio/gpio.h>
+
/ {
aliases {
backlight = &backlight;
@@ -293,7 +295,7 @@
pinctrl-0 = <&pinctrl_usbh>;
vbus-supply = <®_usb_h1_vbus>;
clocks = <&clks IMX6QDL_CLK_CKO>;
- status = "okay";
+ status = "disabled";
};
&usbotg {
diff --git a/arch/arm/dts/imx6qdl-wandboard-revd1.dtsi b/arch/arm/dts/imx6qdl-wandboard-revd1.dtsi
index 93909796885..bf86b639fda 100644
--- a/arch/arm/dts/imx6qdl-wandboard-revd1.dtsi
+++ b/arch/arm/dts/imx6qdl-wandboard-revd1.dtsi
@@ -142,7 +142,6 @@
imx6qdl-wandboard {
pinctrl_hog: hoggrp {
fsl,pins = <
- MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x80000000 /* USB Power Enable */
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* USDHC1 CD */
MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000 /* uSDHC3 CD */
MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f0b1 /* RGMII PHY reset */
@@ -166,7 +165,6 @@
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
>;
};
diff --git a/arch/arm/dts/imx6qdl-wandboard.dtsi b/arch/arm/dts/imx6qdl-wandboard.dtsi
index 35a88bf5a76..ec6fba5ee8f 100644
--- a/arch/arm/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/dts/imx6qdl-wandboard.dtsi
@@ -8,10 +8,6 @@
#include <dt-bindings/gpio/gpio.h>
/ {
- aliases {
- mmc0 = &usdhc3;
- };
-
chosen {
stdout-path = &uart1;
};
@@ -37,6 +33,30 @@
spdif-out;
};
+ reg_1p5v: regulator-1p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P5V";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1P8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_2p8v: regulator-2p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
reg_2p5v: regulator-2p5v {
compatible = "regulator-fixed";
regulator-name = "2P5V";
@@ -77,15 +97,21 @@
&i2c1 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
};
&i2c2 {
clock-frequency = <100000>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
codec: sgtl5000@a {
@@ -98,6 +124,29 @@
VDDIO-supply = <®_3p3v>;
lrclk-strength = <3>;
};
+
+ camera@3c {
+ compatible = "ovti,ov5645";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5645>;
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO2>;
+ clock-names = "xclk";
+ clock-frequency = <24000000>;
+ vdddo-supply = <®_1p8v>;
+ vdda-supply = <®_2p8v>;
+ vddd-supply = <®_1p5v>;
+ enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+
+ port {
+ ov5645_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
};
&iomuxc {
@@ -132,7 +181,6 @@
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
- MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
>;
};
@@ -143,6 +191,13 @@
>;
};
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x4001b8b0
+ MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x4001b8b0
+ >;
+ };
+
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
@@ -150,12 +205,27 @@
>;
};
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b0
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b0
+ >;
+ };
+
pinctrl_mclk: mclkgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
>;
};
+ pinctrl_ov5645: ov5645grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x000b0
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
+ MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0
+ >;
+ };
+
pinctrl_spdif: spdifgrp {
fsl,pins = <
MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1b0b0
@@ -231,9 +301,6 @@
phy-mode = "rgmii-id";
phy-handle = <ðphy>;
phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
- interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
- <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
- fsl,err006687-workaround-present;
status = "okay";
mdio {
@@ -242,6 +309,21 @@
ethphy: ethernet-phy@1 {
reg = <1>;
+ qca,clk-out-frequency = <125000000>;
+ };
+ };
+};
+
+&mipi_csi {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&ov5645_to_mipi_csi2>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
};
};
};
diff --git a/arch/arm/dts/imx6qdl.dtsi b/arch/arm/dts/imx6qdl.dtsi
index d89272039b2..4f7fefc14d0 100644
--- a/arch/arm/dts/imx6qdl.dtsi
+++ b/arch/arm/dts/imx6qdl.dtsi
@@ -4,6 +4,7 @@
// Copyright 2011 Linaro Ltd.
#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
@@ -13,10 +14,8 @@
* The decompressor and also some bootloaders rely on a
* pre-existing /chosen node to be available to insert the
* command line and merge other ATAGS info.
- * Also for U-Boot there must be a pre-existing /memory node.
*/
chosen {};
- memory { device_type = "memory"; };
aliases {
ethernet0 = &fec;
@@ -46,39 +45,34 @@
spi1 = &ecspi2;
spi2 = &ecspi3;
spi3 = &ecspi4;
+ usb0 = &usbotg;
+ usb1 = &usbh1;
+ usb2 = &usbh2;
+ usb3 = &usbh3;
usbphy0 = &usbphy1;
usbphy1 = &usbphy2;
};
clocks {
ckil {
- compatible = "fsl,imx-ckil", "fixed-clock";
+ compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
ckih1 {
- compatible = "fsl,imx-ckih1", "fixed-clock";
+ compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <0>;
};
osc {
- compatible = "fsl,imx-osc", "fixed-clock";
+ compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
};
};
- tempmon: tempmon {
- compatible = "fsl,imx6q-tempmon";
- interrupt-parent = <&gpc>;
- interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
- fsl,tempmon = <&anatop>;
- fsl,tempmon-data = <&ocotp>;
- clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
- };
-
ldb: ldb {
#address-cells = <1>;
#size-cells = <0>;
@@ -139,6 +133,16 @@
interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
};
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -159,10 +163,8 @@
clocks = <&clks IMX6QDL_CLK_APBH_DMA>;
};
- gpmi: gpmi-nand@112000 {
+ gpmi: nand-controller@112000 {
compatible = "fsl,imx6q-gpmi-nand";
- #address-cells = <1>;
- #size-cells = <1>;
reg = <0x00112000 0x2000>, <0x00114000 0x2000>;
reg-names = "gpmi-nand", "bch";
interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -180,8 +182,6 @@
};
hdmi: hdmi@120000 {
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0x00120000 0x9000>;
interrupts = <0 115 0x04>;
gpr = <&gpr>;
@@ -190,19 +190,24 @@
clock-names = "iahb", "isfr";
status = "disabled";
- port@0 {
- reg = <0>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
- hdmi_mux_0: endpoint {
- remote-endpoint = <&ipu1_di0_hdmi>;
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
};
- };
- port@1 {
- reg = <1>;
+ port@1 {
+ reg = <1>;
- hdmi_mux_1: endpoint {
- remote-endpoint = <&ipu1_di1_hdmi>;
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
};
};
};
@@ -216,6 +221,7 @@
<&clks IMX6QDL_CLK_GPU3D_SHADER>;
clock-names = "bus", "core", "shader";
power-domains = <&pd_pu>;
+ #cooling-cells = <2>;
};
gpu_2d: gpu@134000 {
@@ -226,6 +232,7 @@
<&clks IMX6QDL_CLK_GPU2D_CORE>;
clock-names = "bus", "core";
power-domains = <&pd_pu>;
+ #cooling-cells = <2>;
};
timer@a00600 {
@@ -245,7 +252,7 @@
interrupt-parent = <&intc>;
};
- L2: l2-cache@a02000 {
+ L2: cache-controller@a02000 {
compatible = "arm,pl310-cache";
reg = <0x00a02000 0x1000>;
interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>;
@@ -257,7 +264,7 @@
};
pcie: pcie@1ffc000 {
- compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+ compatible = "fsl,imx6q-pcie";
reg = <0x01ffc000 0x04000>,
<0x01f00000 0x80000>;
reg-names = "dbi", "config";
@@ -265,8 +272,8 @@
#size-cells = <2>;
device_type = "pci";
bus-range = <0x00 0xff>;
- ranges = <0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
- 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
+ ranges = <0x81000000 0 0 0x01f80000 0 0x00010000>, /* downstream I/O */
+ <0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
num-lanes = <1>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
@@ -326,7 +333,7 @@
clocks = <&clks IMX6QDL_CLK_ECSPI1>,
<&clks IMX6QDL_CLK_ECSPI1>;
clock-names = "ipg", "per";
- dmas = <&sdma 3 8 1>, <&sdma 4 8 2>;
+ dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
dma-names = "rx", "tx";
status = "disabled";
};
@@ -340,7 +347,7 @@
clocks = <&clks IMX6QDL_CLK_ECSPI2>,
<&clks IMX6QDL_CLK_ECSPI2>;
clock-names = "ipg", "per";
- dmas = <&sdma 5 8 1>, <&sdma 6 8 2>;
+ dmas = <&sdma 5 7 1>, <&sdma 6 7 2>;
dma-names = "rx", "tx";
status = "disabled";
};
@@ -354,7 +361,7 @@
clocks = <&clks IMX6QDL_CLK_ECSPI3>,
<&clks IMX6QDL_CLK_ECSPI3>;
clock-names = "ipg", "per";
- dmas = <&sdma 7 8 1>, <&sdma 8 8 2>;
+ dmas = <&sdma 7 7 1>, <&sdma 8 7 2>;
dma-names = "rx", "tx";
status = "disabled";
};
@@ -368,7 +375,7 @@
clocks = <&clks IMX6QDL_CLK_ECSPI4>,
<&clks IMX6QDL_CLK_ECSPI4>;
clock-names = "ipg", "per";
- dmas = <&sdma 9 8 1>, <&sdma 10 8 2>;
+ dmas = <&sdma 9 7 1>, <&sdma 10 7 2>;
dma-names = "rx", "tx";
status = "disabled";
};
@@ -474,7 +481,7 @@
status = "okay";
};
- spba@203c000 {
+ spba-bus@203c000 {
reg = <0x0203c000 0x4000>;
};
};
@@ -498,7 +505,7 @@
};
pwm1: pwm@2080000 {
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x02080000 0x4000>;
interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>;
@@ -509,7 +516,7 @@
};
pwm2: pwm@2084000 {
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x02084000 0x4000>;
interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
@@ -520,7 +527,7 @@
};
pwm3: pwm@2088000 {
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x02088000 0x4000>;
interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
@@ -531,7 +538,7 @@
};
pwm4: pwm@208c000 {
- #pwm-cells = <2>;
+ #pwm-cells = <3>;
compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
reg = <0x0208c000 0x4000>;
interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
@@ -541,27 +548,29 @@
status = "disabled";
};
- can1: flexcan@2090000 {
+ can1: can@2090000 {
compatible = "fsl,imx6q-flexcan";
reg = <0x02090000 0x4000>;
interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_CAN1_IPG>,
<&clks IMX6QDL_CLK_CAN1_SERIAL>;
clock-names = "ipg", "per";
+ fsl,stop-mode = <&gpr 0x34 28>;
status = "disabled";
};
- can2: flexcan@2094000 {
+ can2: can@2094000 {
compatible = "fsl,imx6q-flexcan";
reg = <0x02094000 0x4000>;
interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_CAN2_IPG>,
<&clks IMX6QDL_CLK_CAN2_SERIAL>;
clock-names = "ipg", "per";
+ fsl,stop-mode = <&gpr 0x34 29>;
status = "disabled";
};
- gpt: gpt@2098000 {
+ gpt: timer@2098000 {
compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt";
reg = <0x02098000 0x4000>;
interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
@@ -648,7 +657,7 @@
#interrupt-cells = <2>;
};
- kpp: kpp@20b8000 {
+ kpp: keypad@20b8000 {
compatible = "fsl,imx6q-kpp", "fsl,imx21-kpp";
reg = <0x020b8000 0x4000>;
interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -656,22 +665,22 @@
status = "disabled";
};
- wdog1: wdog@20bc000 {
+ wdog1: watchdog@20bc000 {
compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
reg = <0x020bc000 0x4000>;
interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6QDL_CLK_DUMMY>;
+ clocks = <&clks IMX6QDL_CLK_IPG>;
};
- wdog2: wdog@20c0000 {
+ wdog2: watchdog@20c0000 {
compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
reg = <0x020c0000 0x4000>;
interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6QDL_CLK_DUMMY>;
+ clocks = <&clks IMX6QDL_CLK_IPG>;
status = "disabled";
};
- clks: ccm@20c4000 {
+ clks: clock-controller@20c4000 {
compatible = "fsl,imx6q-ccm";
reg = <0x020c4000 0x4000>;
interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>,
@@ -680,7 +689,7 @@
};
anatop: anatop@20c8000 {
- compatible = "fsl,imx6q-anatop", "syscon", "simple-bus";
+ compatible = "fsl,imx6q-anatop", "syscon", "simple-mfd";
reg = <0x020c8000 0x1000>;
interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>,
<0 54 IRQ_TYPE_LEVEL_HIGH>,
@@ -753,7 +762,7 @@
regulator-name = "vddpu";
regulator-min-microvolt = <725000>;
regulator-max-microvolt = <1450000>;
- regulator-enable-ramp-delay = <150>;
+ regulator-enable-ramp-delay = <380>;
anatop-reg-offset = <0x140>;
anatop-vol-bit-shift = <9>;
anatop-vol-bit-width = <5>;
@@ -781,6 +790,17 @@
anatop-min-voltage = <725000>;
anatop-max-voltage = <1450000>;
};
+
+ tempmon: tempmon {
+ compatible = "fsl,imx6q-tempmon";
+ interrupt-parent = <&gpc>;
+ interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,tempmon = <&anatop>;
+ nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+ nvmem-cell-names = "calib", "temp_grade";
+ clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+ #thermal-sensor-cells = <0>;
+ };
};
usbphy1: usbphy@20c9000 {
@@ -820,6 +840,15 @@
status = "disabled";
};
+ snvs_pwrkey: snvs-powerkey {
+ compatible = "fsl,sec-v4.0-pwrkey";
+ regmap = <&snvs>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ linux,keycode = <KEY_POWER>;
+ wakeup-source;
+ status = "disabled";
+ };
+
snvs_lpgpr: snvs-lpgpr {
compatible = "fsl,imx6q-snvs-lpgpr";
};
@@ -835,7 +864,7 @@
interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
};
- src: src@20d8000 {
+ src: reset-controller@20d8000 {
compatible = "fsl,imx6q-src", "fsl,imx51-src";
reg = <0x020d8000 0x4000>;
interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -848,8 +877,7 @@
reg = <0x020dc000 0x4000>;
interrupt-controller;
#interrupt-cells = <3>;
- interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
- <0 90 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>;
interrupt-parent = <&intc>;
clocks = <&clks IMX6QDL_CLK_IPG>;
clock-names = "ipg";
@@ -886,7 +914,7 @@
};
};
- iomuxc: iomuxc@20e0000 {
+ iomuxc: pinctrl@20e0000 {
compatible = "fsl,imx6dl-iomuxc", "fsl,imx6q-iomuxc";
reg = <0x20e0000 0x4000>;
};
@@ -905,7 +933,7 @@
compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
reg = <0x020ec000 0x4000>;
interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6QDL_CLK_SDMA>,
+ clocks = <&clks IMX6QDL_CLK_IPG>,
<&clks IMX6QDL_CLK_SDMA>;
clock-names = "ipg", "ahb";
#dma-cells = <3>;
@@ -913,14 +941,14 @@
};
};
- bus@2100000 { /* AIPS2 */
+ aips2: bus@2100000 { /* AIPS2 */
compatible = "fsl,aips-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x02100000 0x100000>;
ranges;
- crypto: caam@2100000 {
+ crypto: crypto@2100000 {
compatible = "fsl,sec-v4.0";
#address-cells = <1>;
#size-cells = <1>;
@@ -932,13 +960,13 @@
<&clks IMX6QDL_CLK_EIM_SLOW>;
clock-names = "mem", "aclk", "ipg", "emi_slow";
- sec_jr0: jr0@1000 {
+ sec_jr0: jr@1000 {
compatible = "fsl,sec-v4.0-job-ring";
reg = <0x1000 0x1000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
};
- sec_jr1: jr1@2000 {
+ sec_jr1: jr@2000 {
compatible = "fsl,sec-v4.0-job-ring";
reg = <0x2000 0x1000>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
@@ -981,6 +1009,8 @@
reg = <0x02184400 0x200>;
interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop1>;
+ phy_type = "hsic";
fsl,usbmisc = <&usbmisc 2>;
dr_mode = "host";
ahb-burst-config = <0x0>;
@@ -994,6 +1024,8 @@
reg = <0x02184600 0x200>;
interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphynop2>;
+ phy_type = "hsic";
fsl,usbmisc = <&usbmisc 3>;
dr_mode = "host";
ahb-burst-config = <0x0>;
@@ -1013,13 +1045,14 @@
compatible = "fsl,imx6q-fec";
reg = <0x02188000 0x4000>;
interrupt-names = "int0", "pps";
- interrupts-extended =
- <&intc 0 118 IRQ_TYPE_LEVEL_HIGH>,
- <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>,
+ <0 119 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_ENET>,
<&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET_REF>,
<&clks IMX6QDL_CLK_ENET_REF>;
- clock-names = "ipg", "ahb", "ptp";
+ clock-names = "ipg", "ahb", "ptp", "enet_out";
+ fsl,stop-mode = <&gpr 0x34 27>;
status = "disabled";
};
@@ -1030,7 +1063,7 @@
<0 126 IRQ_TYPE_LEVEL_HIGH>;
};
- usdhc1: usdhc@2190000 {
+ usdhc1: mmc@2190000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x02190000 0x4000>;
interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -1042,7 +1075,7 @@
status = "disabled";
};
- usdhc2: usdhc@2194000 {
+ usdhc2: mmc@2194000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x02194000 0x4000>;
interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
@@ -1054,7 +1087,7 @@
status = "disabled";
};
- usdhc3: usdhc@2198000 {
+ usdhc3: mmc@2198000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x02198000 0x4000>;
interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
@@ -1066,7 +1099,7 @@
status = "disabled";
};
- usdhc4: usdhc@219c000 {
+ usdhc4: mmc@219c000 {
compatible = "fsl,imx6q-usdhc";
reg = <0x0219c000 0x4000>;
interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
@@ -1112,13 +1145,16 @@
reg = <0x021ac000 0x4000>;
};
- mmdc0: mmdc@21b0000 { /* MMDC0 */
+ mmdc0: memory-controller@21b0000 { /* MMDC0 */
compatible = "fsl,imx6q-mmdc";
reg = <0x021b0000 0x4000>;
+ clocks = <&clks IMX6QDL_CLK_MMDC_P0_IPG>;
};
- mmdc1: mmdc@21b4000 { /* MMDC1 */
+ mmdc1: memory-controller@21b4000 { /* MMDC1 */
+ compatible = "fsl,imx6q-mmdc";
reg = <0x021b4000 0x4000>;
+ status = "disabled";
};
weim: weim@21b8000 {
@@ -1132,10 +1168,24 @@
status = "disabled";
};
- ocotp: ocotp@21bc000 {
+ ocotp: efuse@21bc000 {
compatible = "fsl,imx6q-ocotp", "syscon";
reg = <0x021bc000 0x4000>;
clocks = <&clks IMX6QDL_CLK_IIM>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpu_speed_grade: speed-grade@10 {
+ reg = <0x10 4>;
+ };
+
+ tempmon_calib: calib@38 {
+ reg = <0x38 4>;
+ };
+
+ tempmon_temp_grade: temp-grade@20 {
+ reg = <0x20 4>;
+ };
};
tzasc@21d0000 { /* TZASC1 */
diff --git a/include/dt-bindings/clock/imx6qdl-clock.h b/include/dt-bindings/clock/imx6qdl-clock.h
index 29050337d9d..e20c43cc36f 100644
--- a/include/dt-bindings/clock/imx6qdl-clock.h
+++ b/include/dt-bindings/clock/imx6qdl-clock.h
@@ -1,9 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Copyright 2014 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
*/
#ifndef __DT_BINDINGS_CLOCK_IMX6QDL_H
@@ -269,6 +266,13 @@
#define IMX6QDL_CLK_PRG0_APB 256
#define IMX6QDL_CLK_PRG1_APB 257
#define IMX6QDL_CLK_PRE_AXI 258
-#define IMX6QDL_CLK_END 259
+#define IMX6QDL_CLK_MLB_SEL 259
+#define IMX6QDL_CLK_MLB_PODF 260
+#define IMX6QDL_CLK_EPIT1 261
+#define IMX6QDL_CLK_EPIT2 262
+#define IMX6QDL_CLK_MMDC_P0_IPG 263
+#define IMX6QDL_CLK_DCIC1 264
+#define IMX6QDL_CLK_DCIC2 265
+#define IMX6QDL_CLK_END 266
#endif /* __DT_BINDINGS_CLOCK_IMX6QDL_H */
--
2.35.1
next prev parent reply other threads:[~2022-07-21 13:34 UTC|newest]
Thread overview: 72+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-07-21 13:27 [PATCH v1 00/26] arm: dts: imx: sync device trees with upstream linux kernel ones Marcel Ziswiler
2022-07-21 13:27 ` [PATCH v1 01/26] board/BuR/brppt2: fix pwms property warning Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 02/26] imx6: aristainetos: fix pwms property warnings Marcel Ziswiler
2022-07-22 5:18 ` Heiko Schocher
2022-07-25 16:40 ` sbabic
2022-07-21 13:27 ` [PATCH v1 03/26] tbs2910: prepare to synchronise device trees with linux Marcel Ziswiler
2022-07-21 17:20 ` Soeren Moch
2022-07-21 18:56 ` Marcel Ziswiler
2022-07-21 19:18 ` Fabio Estevam
2022-08-03 12:50 ` Marcel Ziswiler
2022-07-25 16:42 ` sbabic
2022-07-25 21:55 ` Soeren Moch
2022-07-21 13:27 ` Marcel Ziswiler [this message]
2022-07-25 16:42 ` [PATCH v1 04/26] imx6dl/imx6qdl: " sbabic
2022-07-21 13:27 ` [PATCH v1 05/26] apalis_imx6: synchronise device tree " Marcel Ziswiler
2022-07-25 16:40 ` sbabic
2022-07-21 13:27 ` [PATCH v1 06/26] colibri_imx6: " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 07/26] imx: mx6ul_14x14_evk: prepare to synchronise device trees " Marcel Ziswiler
2022-07-25 16:42 ` sbabic
2022-07-21 13:27 ` [PATCH v1 08/26] imx6ul/imx6ull: " Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-08-01 8:08 ` Frieder Schrempf
2022-08-01 11:26 ` Stefano Babic
2022-08-03 12:58 ` Marcel Ziswiler
2022-08-03 13:02 ` Stefano Babic
2022-08-03 13:21 ` Frieder Schrempf
2022-08-23 14:37 ` Frieder Schrempf
2022-07-21 13:27 ` [PATCH v1 09/26] colibri-imx6ull/-emmc: synchronise device tree " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 10/26] imx: imx7-cm: prepare to synchronise device trees " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 11/26] imx: imx7d-sdb: " Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-07-21 13:27 ` [PATCH v1 12/26] imx7s/d: " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 13/26] colibri-imx7d/-emmc: synchronise device tree " Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-07-21 13:27 ` [PATCH v1 14/26] ARM: DTS: bk4r1/pcm052: prepare to synchronise device trees " Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-07-21 13:27 ` [PATCH v1 15/26] vf500/vf610: " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 16/26] colibri_vf: synchronise device tree " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 17/26] imx8mm-venice-gw700x: prepare to synchronise device trees " Marcel Ziswiler
2022-07-25 16:42 ` sbabic
2022-07-21 13:27 ` [PATCH v1 18/26] imx8mm: synchronise device tree " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:27 ` [PATCH v1 19/26] imx8mm-kontron-n801x-s-lvds: fix pwms property warnings Marcel Ziswiler
2022-07-25 16:40 ` sbabic
2022-07-21 13:41 ` [PATCH v1 20/26] imx8mm-mx8menlo/verdin-imx8mm: synchronise device tree with linux Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-07-21 13:43 ` [PATCH v1 21/26] imx8mn: " Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-31 16:58 ` Adam Ford
2022-08-03 13:02 ` Marcel Ziswiler
2022-08-12 12:49 ` Adam Ford
2022-08-12 13:02 ` Francesco Dolcini
2022-07-21 13:44 ` [PATCH v1 22/26] imx8mp: " Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-07-21 13:45 ` [PATCH v1 23/26] imx8mp-rsb3720-a1: fix pwms property warnings Marcel Ziswiler
2022-07-25 16:42 ` sbabic
2022-07-21 13:46 ` [PATCH v1 24/26] verdin-imx8mp: synchronise device tree with linux Marcel Ziswiler
2022-07-25 16:41 ` sbabic
2022-07-21 13:47 ` [PATCH v1 25/26] imx8mq: " Marcel Ziswiler
2022-07-25 16:39 ` sbabic
2022-09-06 12:36 ` Heiko Thiery
2022-09-06 14:05 ` Marcel Ziswiler
2022-09-06 14:32 ` Heiko Thiery
2022-07-21 13:48 ` [PATCH v1 26/26] board: toradex: apalis-imx8: fix file names in maintainers Marcel Ziswiler
2022-07-25 16:41 ` sbabic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220721132748.1052244-5-marcel@ziswiler.com \
--to=marcel@ziswiler.com \
--cc=aford173@gmail.com \
--cc=festevam@gmail.com \
--cc=ian.ray@ge.com \
--cc=jagan@amarulasolutions.com \
--cc=marcel.ziswiler@toradex.com \
--cc=martyn.welch@collabora.com \
--cc=matthias.winker@de.bosch.com \
--cc=pro@denx.de \
--cc=raffaele.recalcati@bticino.it \
--cc=sbabic@denx.de \
--cc=simone.cianni@bticino.it \
--cc=smoch@web.de \
--cc=tharvey@gateworks.com \
--cc=troy.kisky@boundarydevices.com \
--cc=u-boot@lists.denx.de \
--cc=uboot-imx@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.