* [PATCH v5 0/5] Add SPI Driver to HPE GXP Architecture
@ 2022-07-27 16:47 ` nick.hawkins
0 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Changes since v5:
*Fixed indentation in Kconfig file
Changes since v4:
*Removed unnecessary quotes in hpe,gxp-spifi.yaml
Changes since v3:
*Fixed indentations in hpe,gxp-spifi.yaml
Changes since v2:
*Changed the CONFIG_SPI_GXP from y to m in defconfig
*Removed extra space around < > for reg in hpe,gxp-spifi.yaml
*Changed interrupt-parrent to interrupt-parent in hpe,gxp-spifi.yaml
*Removed repeated include file in spi-gxp.c
*Removed unnecessary initialization of ret variable in spi-gxp.c
*Removed conditional variable checks where failure is not possible in
spi-gxp.c
*Removed unnecessary variable cs in spi-gxp.c
*Removed blank gxp-spifi-remove function in spi-gxp.c
*Fixed error messages so they are not repetitive
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
Nick Hawkins (5):
spi: spi-gxp: Add support for HPE GXP SoCs
spi: dt-bindings: add documentation for hpe,gxp-spifi
ARM: dts: hpe: Add spi driver node
ARM: configs: multi_v7_defconfig: Enable HPE GXP SPI driver
MAINTAINERS: add spi support to GXP
.../bindings/spi/hpe,gxp-spifi.yaml | 56 +++
MAINTAINERS | 2 +
arch/arm/boot/dts/hpe-bmc-dl360gen10.dts | 58 ++++
arch/arm/boot/dts/hpe-gxp.dtsi | 21 +-
arch/arm/configs/multi_v7_defconfig | 1 +
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-gxp.c | 325 ++++++++++++++++++
8 files changed, 470 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
create mode 100644 drivers/spi/spi-gxp.c
--
2.17.1
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 1/5] spi: spi-gxp: Add support for HPE GXP SoCs
2022-07-27 16:47 ` nick.hawkins
@ 2022-07-27 16:47 ` nick.hawkins
-1 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
---
v5:
*Add missing spaces in Kconfig to have proper alignment
v4:
*No change
v3:
*No change
v2:
*Removed repeated include file
*Removed unnecessary initialization of ret variable
*Removed conditional variable checks where failure is impossible
*Removed unecessary variable cs and instead used in the initialization
*Removed blank gxp_spifi_remove function
*Fixed error messages so they are not repetitive
---
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-gxp.c | 325 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 333 insertions(+)
create mode 100644 drivers/spi/spi-gxp.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 3b1044ebc400..e3787cd9b475 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -371,6 +371,13 @@ config SPI_FSL_QUADSPI
This controller does not support generic SPI messages. It only
supports the high-level SPI memory interface.
+config SPI_GXP
+ tristate "GXP SPI driver"
+ depends on ARCH_HPE || COMPILE_TEST
+ help
+ This enables support for the driver for GXP bus attached SPI
+ controllers.
+
config SPI_HISI_KUNPENG
tristate "HiSilicon SPI Controller for Kunpeng SoCs"
depends on (ARM64 && ACPI) || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 0f44eb6083a5..ca5f204017ee 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_SPI_FSL_LPSPI) += spi-fsl-lpspi.o
obj-$(CONFIG_SPI_FSL_QUADSPI) += spi-fsl-qspi.o
obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o
obj-$(CONFIG_SPI_GPIO) += spi-gpio.o
+obj-$(CONFIG_SPI_GXP) += spi-gxp.o
obj-$(CONFIG_SPI_HISI_KUNPENG) += spi-hisi-kunpeng.o
obj-$(CONFIG_SPI_HISI_SFC_V3XX) += spi-hisi-sfc-v3xx.o
obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o
diff --git a/drivers/spi/spi-gxp.c b/drivers/spi/spi-gxp.c
new file mode 100644
index 000000000000..9ea355f7d64f
--- /dev/null
+++ b/drivers/spi/spi-gxp.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0=or-later
+/* Copyright (C) 2022 Hewlett-Packard Development Company, L.P. */
+
+#include <linux/iopoll.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#define GXP_SPI0_MAX_CHIPSELECT 2
+#define GXP_SPI_SLEEP_TIME 1
+#define GXP_SPI_TIMEOUT (130 * 1000000 / GXP_SPI_SLEEP_TIME)
+
+#define MANUAL_MODE 0
+#define DIRECT_MODE 1
+#define SPILDAT_LEN 256
+
+#define OFFSET_SPIMCFG 0x0
+#define OFFSET_SPIMCTRL 0x4
+#define OFFSET_SPICMD 0x5
+#define OFFSET_SPIDCNT 0x6
+#define OFFSET_SPIADDR 0x8
+#define OFFSET_SPIINTSTS 0xc
+
+#define SPIMCTRL_START 0x01
+#define SPIMCTRL_BUSY 0x02
+#define SPIMCTRL_DIR 0x08
+
+struct gxp_spi;
+
+struct gxp_spi_chip {
+ struct gxp_spi *spifi;
+ u32 cs;
+};
+
+struct gxp_spi_data {
+ u32 max_cs;
+ u32 mode_bits;
+};
+
+struct gxp_spi {
+ const struct gxp_spi_data *data;
+ void __iomem *reg_base;
+ void __iomem *dat_base;
+ void __iomem *dir_base;
+ struct device *dev;
+ struct gxp_spi_chip chips[GXP_SPI0_MAX_CHIPSELECT];
+};
+
+static void gxp_spi_set_mode(struct gxp_spi *spifi, int mode)
+{
+ u8 value;
+ void __iomem *reg_base = spifi->reg_base;
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+
+ if (mode == MANUAL_MODE) {
+ writeb(0x55, reg_base + OFFSET_SPICMD);
+ writeb(0xaa, reg_base + OFFSET_SPICMD);
+ value &= ~0x30;
+ } else {
+ value |= 0x30;
+ }
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+}
+
+static int gxp_spi_read_reg(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ int ret;
+ struct gxp_spi *spifi = chip->spifi;
+ void __iomem *reg_base = spifi->reg_base;
+ u32 value;
+
+ value = readl(reg_base + OFFSET_SPIMCFG);
+ value &= ~(1 << 24);
+ value |= (chip->cs << 24);
+ value &= ~(0x07 << 16);
+ value &= ~(0x1f << 19);
+ writel(value, reg_base + OFFSET_SPIMCFG);
+
+ writel(0, reg_base + OFFSET_SPIADDR);
+
+ writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+ writew(op->data.nbytes, reg_base + OFFSET_SPIDCNT);
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+ value &= ~SPIMCTRL_DIR;
+ value |= SPIMCTRL_START;
+
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+ ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+ !(value & SPIMCTRL_BUSY),
+ GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+ if (ret) {
+ dev_warn(spifi->dev, "read reg busy time out\n");
+ return ret;
+ }
+
+ memcpy_fromio(op->data.buf.in, spifi->dat_base, op->data.nbytes);
+ return ret;
+}
+
+static int gxp_spi_write_reg(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ int ret;
+ struct gxp_spi *spifi = chip->spifi;
+ void __iomem *reg_base = spifi->reg_base;
+ u32 value;
+
+ value = readl(reg_base + OFFSET_SPIMCFG);
+ value &= ~(1 << 24);
+ value |= (chip->cs << 24);
+ value &= ~(0x07 << 16);
+ value &= ~(0x1f << 19);
+ writel(value, reg_base + OFFSET_SPIMCFG);
+
+ writel(0, reg_base + OFFSET_SPIADDR);
+
+ writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+ memcpy_toio(spifi->dat_base, op->data.buf.in, op->data.nbytes);
+
+ writew(op->data.nbytes, reg_base + OFFSET_SPIDCNT);
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+ value |= SPIMCTRL_DIR;
+ value |= SPIMCTRL_START;
+
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+ ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+ !(value & SPIMCTRL_BUSY),
+ GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+ if (ret)
+ dev_warn(spifi->dev, "write reg busy time out\n");
+
+ return ret;
+}
+
+static ssize_t gxp_spi_read(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ struct gxp_spi *spifi = chip->spifi;
+ u32 offset = op->addr.val;
+
+ if (chip->cs == 0)
+ offset += 0x4000000;
+
+ memcpy_fromio(op->data.buf.in, spifi->dir_base + offset, op->data.nbytes);
+
+ return 0;
+}
+
+static ssize_t gxp_spi_write(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ struct gxp_spi *spifi = chip->spifi;
+ void __iomem *reg_base = spifi->reg_base;
+ u32 write_len;
+ u32 value;
+ int ret;
+
+ write_len = op->data.nbytes;
+ if (write_len > SPILDAT_LEN)
+ write_len = SPILDAT_LEN;
+
+ value = readl(reg_base + OFFSET_SPIMCFG);
+ value &= ~(1 << 24);
+ value |= (chip->cs << 24);
+ value &= ~(0x07 << 16);
+ value |= (op->addr.nbytes << 16);
+ value &= ~(0x1f << 19);
+ writel(value, reg_base + OFFSET_SPIMCFG);
+
+ writel(op->addr.val, reg_base + OFFSET_SPIADDR);
+
+ writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+ writew(write_len, reg_base + OFFSET_SPIDCNT);
+
+ memcpy_toio(spifi->dat_base, op->data.buf.in, write_len);
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+ value |= SPIMCTRL_DIR;
+ value |= SPIMCTRL_START;
+
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+ ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+ !(value & SPIMCTRL_BUSY),
+ GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+ if (ret) {
+ dev_warn(spifi->dev, "write busy time out\n");
+ return ret;
+ }
+
+ return write_len;
+}
+
+static int do_gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ struct gxp_spi *spifi = spi_controller_get_devdata(mem->spi->master);
+ struct gxp_spi_chip *chip = &spifi->chips[mem->spi->chip_select];
+ int ret;
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ if (!op->addr.nbytes)
+ ret = gxp_spi_read_reg(chip, op);
+ else
+ ret = gxp_spi_read(chip, op);
+ } else {
+ if (!op->addr.nbytes)
+ ret = gxp_spi_write_reg(chip, op);
+ else
+ ret = gxp_spi_write(chip, op);
+ }
+
+ return ret;
+}
+
+static int gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ int ret;
+
+ ret = do_gxp_exec_mem_op(mem, op);
+ if (ret)
+ dev_err(&mem->spi->dev, "operation failed: %d", ret);
+
+ return ret;
+}
+
+static const struct spi_controller_mem_ops gxp_spi_mem_ops = {
+ .exec_op = gxp_exec_mem_op,
+};
+
+static int gxp_spi_setup(struct spi_device *spi)
+{
+ struct gxp_spi *spifi = spi_controller_get_devdata(spi->master);
+ unsigned int cs = spi->chip_select;
+ struct gxp_spi_chip *chip = &spifi->chips[cs];
+
+ chip->spifi = spifi;
+ chip->cs = cs;
+
+ gxp_spi_set_mode(spifi, MANUAL_MODE);
+
+ return 0;
+}
+
+static int gxp_spifi_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct gxp_spi_data *data;
+ struct spi_controller *ctlr;
+ struct gxp_spi *spifi;
+ struct resource *res;
+ int ret;
+
+ data = of_device_get_match_data(&pdev->dev);
+
+ ctlr = devm_spi_alloc_master(dev, sizeof(*spifi));
+ if (!ctlr)
+ return -ENOMEM;
+
+ spifi = spi_controller_get_devdata(ctlr);
+
+ platform_set_drvdata(pdev, spifi);
+ spifi->data = data;
+ spifi->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ spifi->reg_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spifi->reg_base))
+ return PTR_ERR(spifi->reg_base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ spifi->dat_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spifi->dat_base))
+ return PTR_ERR(spifi->dat_base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ spifi->dir_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spifi->dir_base))
+ return PTR_ERR(spifi->dir_base);
+
+ ctlr->mode_bits = data->mode_bits;
+ ctlr->bus_num = pdev->id;
+ ctlr->mem_ops = &gxp_spi_mem_ops;
+ ctlr->setup = gxp_spi_setup;
+ ctlr->num_chipselect = data->max_cs;
+ ctlr->dev.of_node = dev->of_node;
+
+ ret = devm_spi_register_controller(dev, ctlr);
+ if (ret) {
+ return dev_err_probe(&pdev->dev, ret,
+ "failed to register spi controller\n");
+ }
+
+ return 0;
+}
+
+static const struct gxp_spi_data gxp_spifi_data = {
+ .max_cs = 2,
+ .mode_bits = 0,
+};
+
+static const struct of_device_id gxp_spifi_match[] = {
+ {.compatible = "hpe,gxp-spifi", .data = &gxp_spifi_data },
+ { /* null */ }
+};
+MODULE_DEVICE_TABLE(of, gxp_spifi_match);
+
+static struct platform_driver gxp_spifi_driver = {
+ .probe = gxp_spifi_probe,
+ .driver = {
+ .name = "gxp-spifi",
+ .of_match_table = gxp_spifi_match,
+ },
+};
+module_platform_driver(gxp_spifi_driver);
+
+MODULE_DESCRIPTION("HPE GXP SPI Flash Interface driver");
+MODULE_AUTHOR("Nick Hawkins <nick.hawkins@hpe.com>");
+MODULE_LICENSE("GPL");
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v5 1/5] spi: spi-gxp: Add support for HPE GXP SoCs
@ 2022-07-27 16:47 ` nick.hawkins
0 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
---
v5:
*Add missing spaces in Kconfig to have proper alignment
v4:
*No change
v3:
*No change
v2:
*Removed repeated include file
*Removed unnecessary initialization of ret variable
*Removed conditional variable checks where failure is impossible
*Removed unecessary variable cs and instead used in the initialization
*Removed blank gxp_spifi_remove function
*Fixed error messages so they are not repetitive
---
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-gxp.c | 325 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 333 insertions(+)
create mode 100644 drivers/spi/spi-gxp.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 3b1044ebc400..e3787cd9b475 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -371,6 +371,13 @@ config SPI_FSL_QUADSPI
This controller does not support generic SPI messages. It only
supports the high-level SPI memory interface.
+config SPI_GXP
+ tristate "GXP SPI driver"
+ depends on ARCH_HPE || COMPILE_TEST
+ help
+ This enables support for the driver for GXP bus attached SPI
+ controllers.
+
config SPI_HISI_KUNPENG
tristate "HiSilicon SPI Controller for Kunpeng SoCs"
depends on (ARM64 && ACPI) || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 0f44eb6083a5..ca5f204017ee 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_SPI_FSL_LPSPI) += spi-fsl-lpspi.o
obj-$(CONFIG_SPI_FSL_QUADSPI) += spi-fsl-qspi.o
obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o
obj-$(CONFIG_SPI_GPIO) += spi-gpio.o
+obj-$(CONFIG_SPI_GXP) += spi-gxp.o
obj-$(CONFIG_SPI_HISI_KUNPENG) += spi-hisi-kunpeng.o
obj-$(CONFIG_SPI_HISI_SFC_V3XX) += spi-hisi-sfc-v3xx.o
obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o
diff --git a/drivers/spi/spi-gxp.c b/drivers/spi/spi-gxp.c
new file mode 100644
index 000000000000..9ea355f7d64f
--- /dev/null
+++ b/drivers/spi/spi-gxp.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0=or-later
+/* Copyright (C) 2022 Hewlett-Packard Development Company, L.P. */
+
+#include <linux/iopoll.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#define GXP_SPI0_MAX_CHIPSELECT 2
+#define GXP_SPI_SLEEP_TIME 1
+#define GXP_SPI_TIMEOUT (130 * 1000000 / GXP_SPI_SLEEP_TIME)
+
+#define MANUAL_MODE 0
+#define DIRECT_MODE 1
+#define SPILDAT_LEN 256
+
+#define OFFSET_SPIMCFG 0x0
+#define OFFSET_SPIMCTRL 0x4
+#define OFFSET_SPICMD 0x5
+#define OFFSET_SPIDCNT 0x6
+#define OFFSET_SPIADDR 0x8
+#define OFFSET_SPIINTSTS 0xc
+
+#define SPIMCTRL_START 0x01
+#define SPIMCTRL_BUSY 0x02
+#define SPIMCTRL_DIR 0x08
+
+struct gxp_spi;
+
+struct gxp_spi_chip {
+ struct gxp_spi *spifi;
+ u32 cs;
+};
+
+struct gxp_spi_data {
+ u32 max_cs;
+ u32 mode_bits;
+};
+
+struct gxp_spi {
+ const struct gxp_spi_data *data;
+ void __iomem *reg_base;
+ void __iomem *dat_base;
+ void __iomem *dir_base;
+ struct device *dev;
+ struct gxp_spi_chip chips[GXP_SPI0_MAX_CHIPSELECT];
+};
+
+static void gxp_spi_set_mode(struct gxp_spi *spifi, int mode)
+{
+ u8 value;
+ void __iomem *reg_base = spifi->reg_base;
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+
+ if (mode == MANUAL_MODE) {
+ writeb(0x55, reg_base + OFFSET_SPICMD);
+ writeb(0xaa, reg_base + OFFSET_SPICMD);
+ value &= ~0x30;
+ } else {
+ value |= 0x30;
+ }
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+}
+
+static int gxp_spi_read_reg(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ int ret;
+ struct gxp_spi *spifi = chip->spifi;
+ void __iomem *reg_base = spifi->reg_base;
+ u32 value;
+
+ value = readl(reg_base + OFFSET_SPIMCFG);
+ value &= ~(1 << 24);
+ value |= (chip->cs << 24);
+ value &= ~(0x07 << 16);
+ value &= ~(0x1f << 19);
+ writel(value, reg_base + OFFSET_SPIMCFG);
+
+ writel(0, reg_base + OFFSET_SPIADDR);
+
+ writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+ writew(op->data.nbytes, reg_base + OFFSET_SPIDCNT);
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+ value &= ~SPIMCTRL_DIR;
+ value |= SPIMCTRL_START;
+
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+ ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+ !(value & SPIMCTRL_BUSY),
+ GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+ if (ret) {
+ dev_warn(spifi->dev, "read reg busy time out\n");
+ return ret;
+ }
+
+ memcpy_fromio(op->data.buf.in, spifi->dat_base, op->data.nbytes);
+ return ret;
+}
+
+static int gxp_spi_write_reg(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ int ret;
+ struct gxp_spi *spifi = chip->spifi;
+ void __iomem *reg_base = spifi->reg_base;
+ u32 value;
+
+ value = readl(reg_base + OFFSET_SPIMCFG);
+ value &= ~(1 << 24);
+ value |= (chip->cs << 24);
+ value &= ~(0x07 << 16);
+ value &= ~(0x1f << 19);
+ writel(value, reg_base + OFFSET_SPIMCFG);
+
+ writel(0, reg_base + OFFSET_SPIADDR);
+
+ writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+ memcpy_toio(spifi->dat_base, op->data.buf.in, op->data.nbytes);
+
+ writew(op->data.nbytes, reg_base + OFFSET_SPIDCNT);
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+ value |= SPIMCTRL_DIR;
+ value |= SPIMCTRL_START;
+
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+ ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+ !(value & SPIMCTRL_BUSY),
+ GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+ if (ret)
+ dev_warn(spifi->dev, "write reg busy time out\n");
+
+ return ret;
+}
+
+static ssize_t gxp_spi_read(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ struct gxp_spi *spifi = chip->spifi;
+ u32 offset = op->addr.val;
+
+ if (chip->cs == 0)
+ offset += 0x4000000;
+
+ memcpy_fromio(op->data.buf.in, spifi->dir_base + offset, op->data.nbytes);
+
+ return 0;
+}
+
+static ssize_t gxp_spi_write(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+ struct gxp_spi *spifi = chip->spifi;
+ void __iomem *reg_base = spifi->reg_base;
+ u32 write_len;
+ u32 value;
+ int ret;
+
+ write_len = op->data.nbytes;
+ if (write_len > SPILDAT_LEN)
+ write_len = SPILDAT_LEN;
+
+ value = readl(reg_base + OFFSET_SPIMCFG);
+ value &= ~(1 << 24);
+ value |= (chip->cs << 24);
+ value &= ~(0x07 << 16);
+ value |= (op->addr.nbytes << 16);
+ value &= ~(0x1f << 19);
+ writel(value, reg_base + OFFSET_SPIMCFG);
+
+ writel(op->addr.val, reg_base + OFFSET_SPIADDR);
+
+ writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+ writew(write_len, reg_base + OFFSET_SPIDCNT);
+
+ memcpy_toio(spifi->dat_base, op->data.buf.in, write_len);
+
+ value = readb(reg_base + OFFSET_SPIMCTRL);
+ value |= SPIMCTRL_DIR;
+ value |= SPIMCTRL_START;
+
+ writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+ ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+ !(value & SPIMCTRL_BUSY),
+ GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+ if (ret) {
+ dev_warn(spifi->dev, "write busy time out\n");
+ return ret;
+ }
+
+ return write_len;
+}
+
+static int do_gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ struct gxp_spi *spifi = spi_controller_get_devdata(mem->spi->master);
+ struct gxp_spi_chip *chip = &spifi->chips[mem->spi->chip_select];
+ int ret;
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ if (!op->addr.nbytes)
+ ret = gxp_spi_read_reg(chip, op);
+ else
+ ret = gxp_spi_read(chip, op);
+ } else {
+ if (!op->addr.nbytes)
+ ret = gxp_spi_write_reg(chip, op);
+ else
+ ret = gxp_spi_write(chip, op);
+ }
+
+ return ret;
+}
+
+static int gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ int ret;
+
+ ret = do_gxp_exec_mem_op(mem, op);
+ if (ret)
+ dev_err(&mem->spi->dev, "operation failed: %d", ret);
+
+ return ret;
+}
+
+static const struct spi_controller_mem_ops gxp_spi_mem_ops = {
+ .exec_op = gxp_exec_mem_op,
+};
+
+static int gxp_spi_setup(struct spi_device *spi)
+{
+ struct gxp_spi *spifi = spi_controller_get_devdata(spi->master);
+ unsigned int cs = spi->chip_select;
+ struct gxp_spi_chip *chip = &spifi->chips[cs];
+
+ chip->spifi = spifi;
+ chip->cs = cs;
+
+ gxp_spi_set_mode(spifi, MANUAL_MODE);
+
+ return 0;
+}
+
+static int gxp_spifi_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct gxp_spi_data *data;
+ struct spi_controller *ctlr;
+ struct gxp_spi *spifi;
+ struct resource *res;
+ int ret;
+
+ data = of_device_get_match_data(&pdev->dev);
+
+ ctlr = devm_spi_alloc_master(dev, sizeof(*spifi));
+ if (!ctlr)
+ return -ENOMEM;
+
+ spifi = spi_controller_get_devdata(ctlr);
+
+ platform_set_drvdata(pdev, spifi);
+ spifi->data = data;
+ spifi->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ spifi->reg_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spifi->reg_base))
+ return PTR_ERR(spifi->reg_base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ spifi->dat_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spifi->dat_base))
+ return PTR_ERR(spifi->dat_base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ spifi->dir_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(spifi->dir_base))
+ return PTR_ERR(spifi->dir_base);
+
+ ctlr->mode_bits = data->mode_bits;
+ ctlr->bus_num = pdev->id;
+ ctlr->mem_ops = &gxp_spi_mem_ops;
+ ctlr->setup = gxp_spi_setup;
+ ctlr->num_chipselect = data->max_cs;
+ ctlr->dev.of_node = dev->of_node;
+
+ ret = devm_spi_register_controller(dev, ctlr);
+ if (ret) {
+ return dev_err_probe(&pdev->dev, ret,
+ "failed to register spi controller\n");
+ }
+
+ return 0;
+}
+
+static const struct gxp_spi_data gxp_spifi_data = {
+ .max_cs = 2,
+ .mode_bits = 0,
+};
+
+static const struct of_device_id gxp_spifi_match[] = {
+ {.compatible = "hpe,gxp-spifi", .data = &gxp_spifi_data },
+ { /* null */ }
+};
+MODULE_DEVICE_TABLE(of, gxp_spifi_match);
+
+static struct platform_driver gxp_spifi_driver = {
+ .probe = gxp_spifi_probe,
+ .driver = {
+ .name = "gxp-spifi",
+ .of_match_table = gxp_spifi_match,
+ },
+};
+module_platform_driver(gxp_spifi_driver);
+
+MODULE_DESCRIPTION("HPE GXP SPI Flash Interface driver");
+MODULE_AUTHOR("Nick Hawkins <nick.hawkins@hpe.com>");
+MODULE_LICENSE("GPL");
--
2.17.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
2022-07-27 16:47 ` nick.hawkins
@ 2022-07-27 16:47 ` nick.hawkins
-1 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Create documentation for the hpe,gxp-spifi binding to support access to
the SPI parts
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
v5:
*No change, add Krzysztof review from previous version
v4:
*Remove uneccessary quotes
v3:
*Fix indentation
v2:
*Removed extra space around < > for reg
*Changed interrupt-parrent to interrupt-parent
---
.../bindings/spi/hpe,gxp-spifi.yaml | 56 +++++++++++++++++++
1 file changed, 56 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
diff --git a/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml b/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
new file mode 100644
index 000000000000..7797c3123b7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/hpe,gxp-spifi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HPE GXP spi controller flash interface
+
+maintainers:
+ - Nick Hawkins <nick.hawkins@hpe.com>
+ - Jean-Marie Verdun <verdun@hpe.com>
+
+allOf:
+ - $ref: spi-controller.yaml#
+
+properties:
+ compatible:
+ const: hpe,gxp-spifi
+
+ reg:
+ items:
+ - description: cfg registers
+ - description: data registers
+ - description: mapped memory
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+
+ spi@200 {
+ compatible = "hpe,gxp-spifi";
+ reg = <0x200 0x80>, <0xc000 0x100>, <0x38000000 0x800000>;
+ interrupts = <20>;
+ interrupt-parent = <&vic0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ };
+
+ flash@1 {
+ reg = <1>;
+ compatible = "jedec,spi-nor";
+ };
+ };
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v5 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
@ 2022-07-27 16:47 ` nick.hawkins
0 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Create documentation for the hpe,gxp-spifi binding to support access to
the SPI parts
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
v5:
*No change, add Krzysztof review from previous version
v4:
*Remove uneccessary quotes
v3:
*Fix indentation
v2:
*Removed extra space around < > for reg
*Changed interrupt-parrent to interrupt-parent
---
.../bindings/spi/hpe,gxp-spifi.yaml | 56 +++++++++++++++++++
1 file changed, 56 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
diff --git a/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml b/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
new file mode 100644
index 000000000000..7797c3123b7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/hpe,gxp-spifi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HPE GXP spi controller flash interface
+
+maintainers:
+ - Nick Hawkins <nick.hawkins@hpe.com>
+ - Jean-Marie Verdun <verdun@hpe.com>
+
+allOf:
+ - $ref: spi-controller.yaml#
+
+properties:
+ compatible:
+ const: hpe,gxp-spifi
+
+ reg:
+ items:
+ - description: cfg registers
+ - description: data registers
+ - description: mapped memory
+
+ interrupts:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+
+ spi@200 {
+ compatible = "hpe,gxp-spifi";
+ reg = <0x200 0x80>, <0xc000 0x100>, <0x38000000 0x800000>;
+ interrupts = <20>;
+ interrupt-parent = <&vic0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ };
+
+ flash@1 {
+ reg = <1>;
+ compatible = "jedec,spi-nor";
+ };
+ };
--
2.17.1
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v5 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
2022-07-27 16:47 ` nick.hawkins
@ 2022-07-27 16:50 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2022-07-27 16:50 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
On 27/07/2022 18:47, nick.hawkins@hpe.com wrote:
> From: Nick Hawkins <nick.hawkins@hpe.com>
>
> Create documentation for the hpe,gxp-spifi binding to support access to
> the SPI parts
>
> Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
>
No blank lines between tags.
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>
> ---
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v5 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
@ 2022-07-27 16:50 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2022-07-27 16:50 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
On 27/07/2022 18:47, nick.hawkins@hpe.com wrote:
> From: Nick Hawkins <nick.hawkins@hpe.com>
>
> Create documentation for the hpe,gxp-spifi binding to support access to
> the SPI parts
>
> Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
>
No blank lines between tags.
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>
> ---
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH v5 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
2022-07-27 16:50 ` Krzysztof Kozlowski
@ 2022-07-27 18:32 ` Hawkins, Nick
-1 siblings, 0 replies; 16+ messages in thread
From: Hawkins, Nick @ 2022-07-27 18:32 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, Verdun, Jean-Marie,
linux, linux-spi, devicetree, linux-kernel, linux-arm-kernel,
arnd, joel
> > From: Nick Hawkins <nick.hawkins@hpe.com>
> >
> > Create documentation for the hpe,gxp-spifi binding to support access
> > to the SPI parts
> >
> > Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
> >
> No blank lines between tags.
> > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> >
> > ---
Apologies, I will make sure in the future to avoid this mistake. I will correct this in v6.
Thank you for all your feedback,
-Nick Hawkins
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 16+ messages in thread
* RE: [PATCH v5 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
@ 2022-07-27 18:32 ` Hawkins, Nick
0 siblings, 0 replies; 16+ messages in thread
From: Hawkins, Nick @ 2022-07-27 18:32 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, Verdun, Jean-Marie,
linux, linux-spi, devicetree, linux-kernel, linux-arm-kernel,
arnd, joel
> > From: Nick Hawkins <nick.hawkins@hpe.com>
> >
> > Create documentation for the hpe,gxp-spifi binding to support access
> > to the SPI parts
> >
> > Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
> >
> No blank lines between tags.
> > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> >
> > ---
Apologies, I will make sure in the future to avoid this mistake. I will correct this in v6.
Thank you for all your feedback,
-Nick Hawkins
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v5 3/5] ARM: dts: hpe: Add spi driver node
2022-07-27 16:47 ` nick.hawkins
@ 2022-07-27 16:47 ` nick.hawkins
-1 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Add support for the SPI flash interface on the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
---
v5:
*No change
v4:
*No change
v3:
*No change
v2:
*No change
---
arch/arm/boot/dts/hpe-bmc-dl360gen10.dts | 58 ++++++++++++++++++++++++
arch/arm/boot/dts/hpe-gxp.dtsi | 21 ++++++++-
2 files changed, 78 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
index 3a7382ce40ef..d49dcef95c5c 100644
--- a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
+++ b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
@@ -24,3 +24,61 @@
reg = <0x40000000 0x20000000>;
};
};
+
+&spifi {
+ status = "okay";
+ flash@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u-boot@0 {
+ label = "u-boot";
+ reg = <0x0 0x60000>;
+ };
+
+ u-boot-env@60000 {
+ label = "u-boot-env";
+ reg = <0x60000 0x20000>;
+ };
+
+ kernel@80000 {
+ label = "kernel";
+ reg = <0x80000 0x4c0000>;
+ };
+
+ rofs@540000 {
+ label = "rofs";
+ reg = <0x540000 0x1740000>;
+ };
+
+ rwfs@1c80000 {
+ label = "rwfs";
+ reg = <0x1c80000 0x250000>;
+ };
+
+ section@1ed0000{
+ label = "section";
+ reg = <0x1ed0000 0x130000>;
+ };
+ };
+ };
+ flash@1 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ host-prime@0 {
+ label = "host-prime";
+ reg = <0x0 0x02000000>;
+ };
+
+ host-second@2000000 {
+ label = "host-second";
+ reg = <0x02000000 0x02000000>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/hpe-gxp.dtsi b/arch/arm/boot/dts/hpe-gxp.dtsi
index cf735b3c4f35..f28349bdeee1 100644
--- a/arch/arm/boot/dts/hpe-gxp.dtsi
+++ b/arch/arm/boot/dts/hpe-gxp.dtsi
@@ -56,9 +56,28 @@
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0x0 0xc0000000 0x30000000>;
+ ranges = <0x0 0xc0000000 0x40000000>;
dma-ranges;
+ spifi: spi@200 {
+ compatible = "hpe,gxp-spifi";
+ reg = <0x200 0x80>, <0xc000 0x100>, <0x38000000 0x8000000>;
+ interrupts = <20>;
+ interrupt-parent = <&vic0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ };
+
+ flash@1 {
+ reg = <1>;
+ compatible = "jedec,spi-nor";
+ };
+ };
+
vic0: interrupt-controller@eff0000 {
compatible = "arm,pl192-vic";
reg = <0xeff0000 0x1000>;
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v5 3/5] ARM: dts: hpe: Add spi driver node
@ 2022-07-27 16:47 ` nick.hawkins
0 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Add support for the SPI flash interface on the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
---
v5:
*No change
v4:
*No change
v3:
*No change
v2:
*No change
---
arch/arm/boot/dts/hpe-bmc-dl360gen10.dts | 58 ++++++++++++++++++++++++
arch/arm/boot/dts/hpe-gxp.dtsi | 21 ++++++++-
2 files changed, 78 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
index 3a7382ce40ef..d49dcef95c5c 100644
--- a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
+++ b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
@@ -24,3 +24,61 @@
reg = <0x40000000 0x20000000>;
};
};
+
+&spifi {
+ status = "okay";
+ flash@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u-boot@0 {
+ label = "u-boot";
+ reg = <0x0 0x60000>;
+ };
+
+ u-boot-env@60000 {
+ label = "u-boot-env";
+ reg = <0x60000 0x20000>;
+ };
+
+ kernel@80000 {
+ label = "kernel";
+ reg = <0x80000 0x4c0000>;
+ };
+
+ rofs@540000 {
+ label = "rofs";
+ reg = <0x540000 0x1740000>;
+ };
+
+ rwfs@1c80000 {
+ label = "rwfs";
+ reg = <0x1c80000 0x250000>;
+ };
+
+ section@1ed0000{
+ label = "section";
+ reg = <0x1ed0000 0x130000>;
+ };
+ };
+ };
+ flash@1 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ host-prime@0 {
+ label = "host-prime";
+ reg = <0x0 0x02000000>;
+ };
+
+ host-second@2000000 {
+ label = "host-second";
+ reg = <0x02000000 0x02000000>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/hpe-gxp.dtsi b/arch/arm/boot/dts/hpe-gxp.dtsi
index cf735b3c4f35..f28349bdeee1 100644
--- a/arch/arm/boot/dts/hpe-gxp.dtsi
+++ b/arch/arm/boot/dts/hpe-gxp.dtsi
@@ -56,9 +56,28 @@
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0x0 0xc0000000 0x30000000>;
+ ranges = <0x0 0xc0000000 0x40000000>;
dma-ranges;
+ spifi: spi@200 {
+ compatible = "hpe,gxp-spifi";
+ reg = <0x200 0x80>, <0xc000 0x100>, <0x38000000 0x8000000>;
+ interrupts = <20>;
+ interrupt-parent = <&vic0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ };
+
+ flash@1 {
+ reg = <1>;
+ compatible = "jedec,spi-nor";
+ };
+ };
+
vic0: interrupt-controller@eff0000 {
compatible = "arm,pl192-vic";
reg = <0xeff0000 0x1000>;
--
2.17.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 4/5] ARM: configs: multi_v7_defconfig: Enable HPE GXP SPI driver
2022-07-27 16:47 ` nick.hawkins
@ 2022-07-27 16:47 ` nick.hawkins
-1 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Enable the SPI driver on the HPE GXP BMC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
v5:
*No change, add Acked-by from Krzsztof from previous version
v4:
*No change
v3:
*No change
v2:
*Change CONFIG_SPI_GXP from y to m
---
arch/arm/configs/multi_v7_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index ce9826bce29b..ee8a730dabc9 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -443,6 +443,7 @@ CONFIG_SPI_CADENCE=y
CONFIG_SPI_DAVINCI=y
CONFIG_SPI_FSL_QUADSPI=m
CONFIG_SPI_GPIO=m
+CONFIG_SPI_GXP=m
CONFIG_SPI_FSL_DSPI=m
CONFIG_SPI_OMAP24XX=y
CONFIG_SPI_ORION=y
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 4/5] ARM: configs: multi_v7_defconfig: Enable HPE GXP SPI driver
@ 2022-07-27 16:47 ` nick.hawkins
0 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Enable the SPI driver on the HPE GXP BMC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
v5:
*No change, add Acked-by from Krzsztof from previous version
v4:
*No change
v3:
*No change
v2:
*Change CONFIG_SPI_GXP from y to m
---
arch/arm/configs/multi_v7_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index ce9826bce29b..ee8a730dabc9 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -443,6 +443,7 @@ CONFIG_SPI_CADENCE=y
CONFIG_SPI_DAVINCI=y
CONFIG_SPI_FSL_QUADSPI=m
CONFIG_SPI_GPIO=m
+CONFIG_SPI_GXP=m
CONFIG_SPI_FSL_DSPI=m
CONFIG_SPI_OMAP24XX=y
CONFIG_SPI_ORION=y
--
2.17.1
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 5/5] MAINTAINERS: add spi support to GXP
2022-07-27 16:47 ` nick.hawkins
@ 2022-07-27 16:47 ` nick.hawkins
-1 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Add the spi driver and dt-binding documentation
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
---
v5:
*No change
v4:
*No change
v3:
*No change
v2:
*No change
---
MAINTAINERS | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index a6d3bd9d2a8d..f87728549ecf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2140,11 +2140,13 @@ M: Jean-Marie Verdun <verdun@hpe.com>
M: Nick Hawkins <nick.hawkins@hpe.com>
S: Maintained
F: Documentation/devicetree/bindings/arm/hpe,gxp.yaml
+F: Documentation/devicetree/bindings/spi/hpe,gxp-spi.yaml
F: Documentation/devicetree/bindings/timer/hpe,gxp-timer.yaml
F: arch/arm/boot/dts/hpe-bmc*
F: arch/arm/boot/dts/hpe-gxp*
F: arch/arm/mach-hpe/
F: drivers/clocksource/timer-gxp.c
+F: drivers/spi/spi-gxp.c
F: drivers/watchdog/gxp-wdt.c
ARM/IGEP MACHINE SUPPORT
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v5 5/5] MAINTAINERS: add spi support to GXP
@ 2022-07-27 16:47 ` nick.hawkins
0 siblings, 0 replies; 16+ messages in thread
From: nick.hawkins @ 2022-07-27 16:47 UTC (permalink / raw)
To: nick.hawkins
Cc: broonie, robh+dt, krzysztof.kozlowski+dt, verdun, linux,
linux-spi, devicetree, linux-kernel, linux-arm-kernel, arnd,
joel
From: Nick Hawkins <nick.hawkins@hpe.com>
Add the spi driver and dt-binding documentation
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
---
v5:
*No change
v4:
*No change
v3:
*No change
v2:
*No change
---
MAINTAINERS | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index a6d3bd9d2a8d..f87728549ecf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2140,11 +2140,13 @@ M: Jean-Marie Verdun <verdun@hpe.com>
M: Nick Hawkins <nick.hawkins@hpe.com>
S: Maintained
F: Documentation/devicetree/bindings/arm/hpe,gxp.yaml
+F: Documentation/devicetree/bindings/spi/hpe,gxp-spi.yaml
F: Documentation/devicetree/bindings/timer/hpe,gxp-timer.yaml
F: arch/arm/boot/dts/hpe-bmc*
F: arch/arm/boot/dts/hpe-gxp*
F: arch/arm/mach-hpe/
F: drivers/clocksource/timer-gxp.c
+F: drivers/spi/spi-gxp.c
F: drivers/watchdog/gxp-wdt.c
ARM/IGEP MACHINE SUPPORT
--
2.17.1
^ permalink raw reply related [flat|nested] 16+ messages in thread