* [PATCH 0/2] Add a new board device tree named 'evoker' for herobrine variant.
@ 2022-09-02 7:42 Sheng-Liang Pan
2022-09-02 7:42 ` [PATCH 1/2] dt-bindings: arm: qcom: document sc7280 and evoker board Sheng-Liang Pan
2022-09-02 7:42 ` [PATCH 2/2] arm64: dts: qcom: sc7280: Add device tree for herobrine evoker Sheng-Liang Pan
0 siblings, 2 replies; 3+ messages in thread
From: Sheng-Liang Pan @ 2022-09-02 7:42 UTC (permalink / raw)
To: LKML
Cc: dianders, mka, Sheng-Liang Pan, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Krzysztof Kozlowski, Rob Herring, devicetree,
linux-arm-msm
This patch add the initial dts file for new board 'evoker'.
Sorry about getting mixed up with version numbers. Here are links to
previous postings and what I'll assume the version number is:
v1: https://lore.kernel.org/r/20220830053307.3997495-1-sheng-liang.pan@quanta.corp-partner.google.com/
v2: https://lore.kernel.org/r/20220901061336.61386-1-sheng-liang.pan@quanta.corp-partner.google.com/
v3: https://lore.kernel.org/r/20220901091253.93333-1-sheng-liang.pan@quanta.corp-partner.google.com/
Changes in v4:
- Got the version number correct
- Got the version number correct
Changes in v2:
- Bindings patch added
Sheng-Liang Pan (2):
dt-bindings: arm: qcom: document sc7280 and evoker board
arm64: dts: qcom: sc7280: Add device tree for herobrine evoker
.../devicetree/bindings/arm/qcom.yaml | 5 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/sc7280-herobrine-evoker-r0.dts | 333 ++++++++++++++++++
3 files changed, 339 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
--
2.34.1
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH 1/2] dt-bindings: arm: qcom: document sc7280 and evoker board
2022-09-02 7:42 [PATCH 0/2] Add a new board device tree named 'evoker' for herobrine variant Sheng-Liang Pan
@ 2022-09-02 7:42 ` Sheng-Liang Pan
2022-09-02 7:42 ` [PATCH 2/2] arm64: dts: qcom: sc7280: Add device tree for herobrine evoker Sheng-Liang Pan
1 sibling, 0 replies; 3+ messages in thread
From: Sheng-Liang Pan @ 2022-09-02 7:42 UTC (permalink / raw)
To: LKML
Cc: dianders, mka, Sheng-Liang Pan, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Krzysztof Kozlowski, Rob Herring, devicetree,
linux-arm-msm
This adds Chromebook Evoker to the yaml.
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
---
Changes in v4:
- Got the version number correct
Changes in v2:
- Bindings patch added
Documentation/devicetree/bindings/arm/qcom.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index fb1d00bcc847c..d4b2d947859d4 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -565,6 +565,11 @@ properties:
- const: google,piglin
- const: qcom,sc7280
+ - description: Google Evoker (newest rev)
+ items:
+ - const: google,evoker
+ - const: qcom,sc7280
+
- description: Google Herobrine (newest rev)
items:
- const: google,herobrine
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH 2/2] arm64: dts: qcom: sc7280: Add device tree for herobrine evoker
2022-09-02 7:42 [PATCH 0/2] Add a new board device tree named 'evoker' for herobrine variant Sheng-Liang Pan
2022-09-02 7:42 ` [PATCH 1/2] dt-bindings: arm: qcom: document sc7280 and evoker board Sheng-Liang Pan
@ 2022-09-02 7:42 ` Sheng-Liang Pan
1 sibling, 0 replies; 3+ messages in thread
From: Sheng-Liang Pan @ 2022-09-02 7:42 UTC (permalink / raw)
To: LKML
Cc: dianders, mka, Sheng-Liang Pan, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Krzysztof Kozlowski, Rob Herring, devicetree,
linux-arm-msm
Add a basic device tree for the herobrine evoker board.
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
---
Changes in v4:
- Got the version number correct
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/sc7280-herobrine-evoker-r0.dts | 333 ++++++++++++++++++
2 files changed, 334 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1d86a33de528c..dd18ae8cd81c2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-r1-lte.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-evoker-r0.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-herobrine-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r0.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
new file mode 100644
index 0000000000000..ccbe50b6249ab
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Evoker board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine.dtsi"
+
+/ {
+ model = "Google Evoker";
+ compatible = "google,evoker", "qcom,sc7280";
+};
+
+/*
+ * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
+ *
+ * Sort order matches the order in the parent files (parents before children).
+ */
+
+&pp3300_codec {
+ status = "okay";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+ap_tp_i2c: &i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ trackpad: trackpad@2c {
+ compatible = "hid-over-i2c";
+ reg = <0x2c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&tp_int_odl>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+ hid-descr-addr = <0x20>;
+ vcc-supply = <&pp3300_z1>;
+
+ wakeup-source;
+ };
+};
+
+ts_i2c: &i2c13 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ ap_ts: touchscreen@10 {
+ compatible = "elan,ekth6915";
+ reg = <0x10>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+ vcc33-supply = <&ts_avdd>;
+ };
+};
+
+&ap_sar_sensor_i2c {
+ status = "okay";
+};
+
+&ap_sar_sensor0 {
+ status = "okay";
+};
+
+&ap_sar_sensor1 {
+ status = "okay";
+};
+
+&mdss_edp {
+ status = "okay";
+};
+
+&mdss_edp_phy {
+ status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+ status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+ status = "okay";
+};
+
+&pwmleds {
+ status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+ status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+ bias-disable;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+ gpio-line-names = "FLASH_STROBE_1", /* 1 */
+ "AP_SUSPEND",
+ "PM8008_1_RST_N",
+ "",
+ "",
+ "",
+ "PMIC_EDP_BL_EN",
+ "PMIC_EDP_BL_PWM",
+ "";
+};
+
+&tlmm {
+ gpio-line-names = "AP_TP_I2C_SDA", /* 0 */
+ "AP_TP_I2C_SCL",
+ "SSD_RST_L",
+ "PE_WAKE_ODL",
+ "AP_SAR_SDA",
+ "AP_SAR_SCL",
+ "PRB_SC_GPIO_6",
+ "TP_INT_ODL",
+ "HP_I2C_SDA",
+ "HP_I2C_SCL",
+
+ "GNSS_L1_EN", /* 10 */
+ "GNSS_L5_EN",
+ "SPI_AP_MOSI",
+ "SPI_AP_MISO",
+ "SPI_AP_CLK",
+ "SPI_AP_CS0_L",
+ /*
+ * AP_FLASH_WP is crossystem ABI. Schematics
+ * call it BIOS_FLASH_WP_OD.
+ */
+ "AP_FLASH_WP",
+ "",
+ "AP_EC_INT_L",
+ "",
+
+ "UF_CAM_RST_L", /* 20 */
+ "WF_CAM_RST_L",
+ "UART_AP_TX_DBG_RX",
+ "UART_DBG_TX_AP_RX",
+ "",
+ "PM8008_IRQ_1",
+ "HOST2WLAN_SOL",
+ "WLAN2HOST_SOL",
+ "MOS_BT_UART_CTS",
+ "MOS_BT_UART_RFR",
+
+ "MOS_BT_UART_TX", /* 30 */
+ "MOS_BT_UART_RX",
+ "PRB_SC_GPIO_32",
+ "HUB_RST_L",
+ "",
+ "",
+ "AP_SPI_FP_MISO",
+ "AP_SPI_FP_MOSI",
+ "AP_SPI_FP_CLK",
+ "AP_SPI_FP_CS_L",
+
+ "AP_EC_SPI_MISO", /* 40 */
+ "AP_EC_SPI_MOSI",
+ "AP_EC_SPI_CLK",
+ "AP_EC_SPI_CS_L",
+ "LCM_RST_L",
+ "EARLY_EUD_N",
+ "",
+ "DP_HOT_PLUG_DET",
+ "IO_BRD_MLB_ID0",
+ "IO_BRD_MLB_ID1",
+
+ "IO_BRD_MLB_ID2", /* 50 */
+ "SSD_EN",
+ "TS_I2C_SDA_CONN",
+ "TS_I2C_CLK_CONN",
+ "TS_RST_CONN",
+ "TS_INT_CONN",
+ "AP_I2C_TPM_SDA",
+ "AP_I2C_TPM_SCL",
+ "PRB_SC_GPIO_58",
+ "PRB_SC_GPIO_59",
+
+ "EDP_HOT_PLUG_DET_N", /* 60 */
+ "FP_TO_AP_IRQ_L",
+ "",
+ "AMP_EN",
+ "CAM0_MCLK_GPIO_64",
+ "CAM1_MCLK_GPIO_65",
+ "WF_CAM_MCLK",
+ "PRB_SC_GPIO_67",
+ "FPMCU_BOOT0",
+ "UF_CAM_SDA",
+
+ "UF_CAM_SCL", /* 70 */
+ "",
+ "",
+ "WF_CAM_SDA",
+ "WF_CAM_SCL",
+ "",
+ "",
+ "EN_FP_RAILS",
+ "FP_RST_L",
+ "PCIE1_CLKREQ_ODL",
+
+ "EN_PP3300_DX_EDP", /* 80 */
+ "SC_GPIO_81",
+ "FORCED_USB_BOOT",
+ "WCD_RESET_N",
+ "MOS_WLAN_EN",
+ "MOS_BT_EN",
+ "MOS_SW_CTRL",
+ "MOS_PCIE0_RST",
+ "MOS_PCIE0_CLKREQ_N",
+ "MOS_PCIE0_WAKE_N",
+
+ "MOS_LAA_AS_EN", /* 90 */
+ "SD_CD_ODL",
+ "",
+ "",
+ "MOS_BT_WLAN_SLIMBUS_CLK",
+ "MOS_BT_WLAN_SLIMBUS_DAT0",
+ "HP_MCLK",
+ "HP_BCLK",
+ "HP_DOUT",
+ "HP_DIN",
+
+ "HP_LRCLK", /* 100 */
+ "HP_IRQ",
+ "",
+ "",
+ "GSC_AP_INT_ODL",
+ "EN_PP3300_CODEC",
+ "AMP_BCLK",
+ "AMP_DIN",
+ "AMP_LRCLK",
+ "UIM1_DATA_GPIO_109",
+
+ "UIM1_CLK_GPIO_110", /* 110 */
+ "UIM1_RESET_GPIO_111",
+ "PRB_SC_GPIO_112",
+ "UIM0_DATA",
+ "UIM0_CLK",
+ "UIM0_RST",
+ "UIM0_PRESENT_ODL",
+ "SDM_RFFE0_CLK",
+ "SDM_RFFE0_DATA",
+ "WF_CAM_EN",
+
+ "FASTBOOT_SEL_0", /* 120 */
+ "SC_GPIO_121",
+ "FASTBOOT_SEL_1",
+ "SC_GPIO_123",
+ "FASTBOOT_SEL_2",
+ "SM_RFFE4_CLK_GRFC_8",
+ "SM_RFFE4_DATA_GRFC_9",
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "PRB_SC_GPIO_129",
+
+ "LCM_ID0", /* 130 */
+ "LCM_ID1",
+ "",
+ "SDR_QLINK_REQ",
+ "SDR_QLINK_EN",
+ "QLINK0_WMSS_RESET_N",
+ "SMR526_QLINK1_REQ",
+ "SMR526_QLINK1_EN",
+ "SMR526_QLINK1_WMSS_RESET_N",
+ "PRB_SC_GPIO_139",
+
+ "SAR1_IRQ_ODL", /* 140 */
+ "SAR0_IRQ_ODL",
+ "PRB_SC_GPIO_142",
+ "",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1",
+ "WCD_SWR_RX_CLK",
+ "WCD_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1",
+
+ "DMIC01_CLK", /* 150 */
+ "DMIC01_DATA",
+ "DMIC23_CLK",
+ "DMIC23_DATA",
+ "",
+ "",
+ "EC_IN_RW_ODL",
+ "HUB_EN",
+ "WCD_SWR_TX_DATA2",
+ "",
+
+ "", /* 160 */
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+ "",
+
+ "", /* 170 */
+ "MOS_BLE_UART_TX",
+ "MOS_BLE_UART_RX",
+ "",
+ "",
+ "";
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-09-02 7:43 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-02 7:42 [PATCH 0/2] Add a new board device tree named 'evoker' for herobrine variant Sheng-Liang Pan
2022-09-02 7:42 ` [PATCH 1/2] dt-bindings: arm: qcom: document sc7280 and evoker board Sheng-Liang Pan
2022-09-02 7:42 ` [PATCH 2/2] arm64: dts: qcom: sc7280: Add device tree for herobrine evoker Sheng-Liang Pan
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.