* [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls
@ 2022-09-30 9:25 Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32 Ashok Reddy Soma
` (3 more replies)
0 siblings, 4 replies; 9+ messages in thread
From: Ashok Reddy Soma @ 2022-09-30 9:25 UTC (permalink / raw)
To: u-boot
Cc: michal.simek, peng.fan, jh80.chung, ayankuma, piyush.mehta,
lakshmi.sai.krishna.potthuri, shravya.kumbham, Ashok Reddy Soma
In this patch series
- Existing node_id is u8, change it to u32 to accommodate Versal node_id
- Read "power-domains" id from DT and use in all firmware calls in place
of node_id.
- Remove static values of node_id which are set based on "device_id"
- Remove "xlnx,device_id" from all dts files
Ashok Reddy Soma (3):
mmc: zynq_sdhci: Change node_id prototype to u32
mmc: zynq_sdhci: Read power-domains id from DT and use
arm64: dts: Remove unused property device_id
arch/arm/dts/versal-mini-emmc0.dts | 1 -
arch/arm/dts/versal-mini-emmc1.dts | 1 -
arch/arm/dts/zynqmp-mini-emmc0.dts | 1 -
arch/arm/dts/zynqmp-mini-emmc1.dts | 1 -
arch/arm/dts/zynqmp.dtsi | 2 --
drivers/mmc/zynq_sdhci.c | 53 +++++++++++++++---------------
6 files changed, 27 insertions(+), 32 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
2022-09-30 9:25 [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Ashok Reddy Soma
@ 2022-09-30 9:25 ` Ashok Reddy Soma
2022-10-07 12:45 ` Jaehoon Chung
2022-09-30 9:25 ` [PATCH 2/3] mmc: zynq_sdhci: Read power-domains id from DT and use Ashok Reddy Soma
` (2 subsequent siblings)
3 siblings, 1 reply; 9+ messages in thread
From: Ashok Reddy Soma @ 2022-09-30 9:25 UTC (permalink / raw)
To: u-boot
Cc: michal.simek, peng.fan, jh80.chung, ayankuma, piyush.mehta,
lakshmi.sai.krishna.potthuri, shravya.kumbham, Ashok Reddy Soma
In Versal platform power domain node_id is bigger than u8, hence
change prototype to u32 to accommodate. Change u8 to u32 in the function
prototypes that use node_id and remove casting to u32 from
xilinx_pm_request() call parameters.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
---
drivers/mmc/zynq_sdhci.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c
index 8f4071c8c2..3a4194452c 100644
--- a/drivers/mmc/zynq_sdhci.c
+++ b/drivers/mmc/zynq_sdhci.c
@@ -111,7 +111,7 @@ static const u8 mode2timing[] = {
[MMC_HS_200] = MMC_TIMING_MMC_HS200,
};
-static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
+static inline int arasan_zynqmp_set_in_tapdelay(u32 node_id, u32 itap_delay)
{
int ret;
@@ -155,7 +155,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
if (ret)
return ret;
} else {
- return xilinx_pm_request(PM_IOCTL, (u32)node_id,
+ return xilinx_pm_request(PM_IOCTL, node_id,
IOCTL_SET_SD_TAPDELAY,
PM_TAPDELAY_INPUT, itap_delay, NULL);
}
@@ -163,7 +163,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
return 0;
}
-static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32 otap_delay)
+static inline int arasan_zynqmp_set_out_tapdelay(u32 node_id, u32 otap_delay)
{
if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
if (node_id == NODE_SD_0)
@@ -174,13 +174,13 @@ static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32 otap_delay)
return zynqmp_mmio_write(SD_OTAP_DLY, SD1_OTAPDLYSEL_MASK,
(otap_delay << 16));
} else {
- return xilinx_pm_request(PM_IOCTL, (u32)node_id,
+ return xilinx_pm_request(PM_IOCTL, node_id,
IOCTL_SET_SD_TAPDELAY,
PM_TAPDELAY_OUTPUT, otap_delay, NULL);
}
}
-static inline int zynqmp_dll_reset(u8 node_id, u32 type)
+static inline int zynqmp_dll_reset(u32 node_id, u32 type)
{
if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
if (node_id == NODE_SD_0)
@@ -192,12 +192,12 @@ static inline int zynqmp_dll_reset(u8 node_id, u32 type)
type == PM_DLL_RESET_ASSERT ?
SD1_DLL_RST : 0);
} else {
- return xilinx_pm_request(PM_IOCTL, (u32)node_id,
+ return xilinx_pm_request(PM_IOCTL, node_id,
IOCTL_SD_DLL_RESET, type, 0, NULL);
}
}
-static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u8 node_id)
+static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u32 node_id)
{
struct mmc *mmc = (struct mmc *)host->mmc;
struct udevice *dev = mmc->dev;
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/3] mmc: zynq_sdhci: Read power-domains id from DT and use
2022-09-30 9:25 [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32 Ashok Reddy Soma
@ 2022-09-30 9:25 ` Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 3/3] arm64: dts: Remove unused property device_id Ashok Reddy Soma
2022-10-04 12:42 ` [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Michal Simek
3 siblings, 0 replies; 9+ messages in thread
From: Ashok Reddy Soma @ 2022-09-30 9:25 UTC (permalink / raw)
To: u-boot
Cc: michal.simek, peng.fan, jh80.chung, ayankuma, piyush.mehta,
lakshmi.sai.krishna.potthuri, shravya.kumbham, Ashok Reddy Soma
Firmware calls need node_id which is basically "power-domains" id.
At present static values are used based on the "device_id" property of
dt.
Instead of this, read "power-domains" id from dt and use it. Add a
element called node_id in priv structure and read it from dt. Replace
static node_id with this priv->node_id across the driver.
Since "device_id" is not used anywhere else simply remove it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
---
drivers/mmc/zynq_sdhci.c | 39 ++++++++++++++++++++-------------------
1 file changed, 20 insertions(+), 19 deletions(-)
diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c
index 3a4194452c..7dcf6ad842 100644
--- a/drivers/mmc/zynq_sdhci.c
+++ b/drivers/mmc/zynq_sdhci.c
@@ -61,7 +61,7 @@ struct arasan_sdhci_plat {
struct arasan_sdhci_priv {
struct sdhci_host *host;
struct arasan_sdhci_clk_data clk_data;
- u8 deviceid;
+ u32 node_id;
u8 bank;
u8 no_1p8;
struct reset_ctl_bulk resets;
@@ -250,7 +250,6 @@ static int arasan_sdhci_execute_tuning(struct mmc *mmc, u8 opcode)
struct sdhci_host *host;
struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev);
char tuning_loop_counter = SDHCI_TUNING_LOOP_COUNT;
- u8 node_id = priv->deviceid ? NODE_SD_1 : NODE_SD_0;
dev_dbg(mmc->dev, "%s\n", __func__);
@@ -262,7 +261,7 @@ static int arasan_sdhci_execute_tuning(struct mmc *mmc, u8 opcode)
mdelay(1);
- arasan_zynqmp_dll_reset(host, node_id);
+ arasan_zynqmp_dll_reset(host, priv->node_id);
sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE);
sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE);
@@ -308,7 +307,7 @@ static int arasan_sdhci_execute_tuning(struct mmc *mmc, u8 opcode)
}
udelay(1);
- arasan_zynqmp_dll_reset(host, node_id);
+ arasan_zynqmp_dll_reset(host, priv->node_id);
/* Enable only interrupts served by the SD controller */
sdhci_writel(host, SDHCI_INT_DATA_MASK | SDHCI_INT_CMD_MASK,
@@ -334,7 +333,6 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct sdhci_host *host,
struct mmc *mmc = (struct mmc *)host->mmc;
struct udevice *dev = mmc->dev;
struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev);
- u8 node_id = priv->deviceid ? NODE_SD_1 : NODE_SD_0;
u8 tap_delay, tap_max = 0;
int timing = mode2timing[mmc->selected_mode];
int ret;
@@ -374,14 +372,14 @@ static int sdhci_zynqmp_sdcardclk_set_phase(struct sdhci_host *host,
tap_delay &= SDHCI_ARASAN_OTAPDLY_SEL_MASK;
/* Set the Clock Phase */
- ret = arasan_zynqmp_set_out_tapdelay(node_id, tap_delay);
+ ret = arasan_zynqmp_set_out_tapdelay(priv->node_id, tap_delay);
if (ret) {
dev_err(dev, "Error setting output Tap Delay\n");
return ret;
}
/* Release DLL Reset */
- ret = zynqmp_dll_reset(node_id, PM_DLL_RESET_RELEASE);
+ ret = zynqmp_dll_reset(priv->node_id, PM_DLL_RESET_RELEASE);
if (ret) {
dev_err(dev, "dll_reset release failed with err: %d\n", ret);
return ret;
@@ -405,7 +403,6 @@ static int sdhci_zynqmp_sampleclk_set_phase(struct sdhci_host *host,
struct mmc *mmc = (struct mmc *)host->mmc;
struct udevice *dev = mmc->dev;
struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev);
- u8 node_id = priv->deviceid ? NODE_SD_1 : NODE_SD_0;
u8 tap_delay, tap_max = 0;
int timing = mode2timing[mmc->selected_mode];
int ret;
@@ -419,7 +416,7 @@ static int sdhci_zynqmp_sampleclk_set_phase(struct sdhci_host *host,
return 0;
/* Assert DLL Reset */
- ret = zynqmp_dll_reset(node_id, PM_DLL_RESET_ASSERT);
+ ret = zynqmp_dll_reset(priv->node_id, PM_DLL_RESET_ASSERT);
if (ret) {
dev_err(dev, "dll_reset assert failed with err: %d\n", ret);
return ret;
@@ -451,7 +448,7 @@ static int sdhci_zynqmp_sampleclk_set_phase(struct sdhci_host *host,
/* Limit input tap_delay value to 8 bits */
tap_delay &= SDHCI_ARASAN_ITAPDLY_SEL_MASK;
- ret = arasan_zynqmp_set_in_tapdelay(node_id, tap_delay);
+ ret = arasan_zynqmp_set_in_tapdelay(priv->node_id, tap_delay);
if (ret) {
dev_err(dev, "Error setting Input Tap Delay\n");
return ret;
@@ -717,14 +714,14 @@ static int sdhci_zynqmp_set_dynamic_config(struct arasan_sdhci_priv *priv,
struct udevice *dev)
{
int ret;
- u32 node_id = priv->deviceid ? NODE_SD_1 : NODE_SD_0;
struct clk clk;
unsigned long clock, mhz;
- ret = xilinx_pm_request(PM_REQUEST_NODE, node_id, ZYNQMP_PM_CAPABILITY_ACCESS,
- ZYNQMP_PM_MAX_QOS, ZYNQMP_PM_REQUEST_ACK_NO, NULL);
+ ret = xilinx_pm_request(PM_REQUEST_NODE, priv->node_id,
+ ZYNQMP_PM_CAPABILITY_ACCESS, ZYNQMP_PM_MAX_QOS,
+ ZYNQMP_PM_REQUEST_ACK_NO, NULL);
if (ret) {
- dev_err(dev, "Request node failed for %d\n", node_id);
+ dev_err(dev, "Request node failed for %d\n", priv->node_id);
return ret;
}
@@ -743,13 +740,13 @@ static int sdhci_zynqmp_set_dynamic_config(struct arasan_sdhci_priv *priv,
return ret;
}
- ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_FIXED, 0);
+ ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_FIXED, 0);
if (ret) {
dev_err(dev, "SD_CONFIG_FIXED failed\n");
return ret;
}
- ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_EMMC_SEL,
+ ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_EMMC_SEL,
dev_read_bool(dev, "non-removable"));
if (ret) {
dev_err(dev, "SD_CONFIG_EMMC_SEL failed\n");
@@ -779,13 +776,13 @@ static int sdhci_zynqmp_set_dynamic_config(struct arasan_sdhci_priv *priv,
else
mhz = 25;
- ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_BASECLK, mhz);
+ ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_BASECLK, mhz);
if (ret) {
dev_err(dev, "SD_CONFIG_BASECLK failed\n");
return ret;
}
- ret = zynqmp_pm_set_sd_config(node_id, SD_CONFIG_8BIT,
+ ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_8BIT,
(dev_read_u32_default(dev, "bus-width", 1) == 8));
if (ret) {
dev_err(dev, "SD_CONFIG_8BIT failed\n");
@@ -900,6 +897,7 @@ static int arasan_sdhci_probe(struct udevice *dev)
static int arasan_sdhci_of_to_plat(struct udevice *dev)
{
struct arasan_sdhci_priv *priv = dev_get_priv(dev);
+ u32 pm_info[2];
priv->host = calloc(1, sizeof(struct sdhci_host));
if (!priv->host)
@@ -916,10 +914,13 @@ static int arasan_sdhci_of_to_plat(struct udevice *dev)
if (IS_ERR(priv->host->ioaddr))
return PTR_ERR(priv->host->ioaddr);
- priv->deviceid = dev_read_u32_default(dev, "xlnx,device_id", -1);
priv->bank = dev_read_u32_default(dev, "xlnx,mio-bank", 0);
priv->no_1p8 = dev_read_bool(dev, "no-1-8-v");
+ priv->node_id = 0;
+ if (!dev_read_u32_array(dev, "power-domains", pm_info, ARRAY_SIZE(pm_info)))
+ priv->node_id = pm_info[1];
+
return 0;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 3/3] arm64: dts: Remove unused property device_id
2022-09-30 9:25 [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32 Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 2/3] mmc: zynq_sdhci: Read power-domains id from DT and use Ashok Reddy Soma
@ 2022-09-30 9:25 ` Ashok Reddy Soma
2022-10-04 12:42 ` [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Michal Simek
3 siblings, 0 replies; 9+ messages in thread
From: Ashok Reddy Soma @ 2022-09-30 9:25 UTC (permalink / raw)
To: u-boot
Cc: michal.simek, peng.fan, jh80.chung, ayankuma, piyush.mehta,
lakshmi.sai.krishna.potthuri, shravya.kumbham, Ashok Reddy Soma
Device tree property "xlnx,device_id" is not used anymore, remove it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
---
arch/arm/dts/versal-mini-emmc0.dts | 1 -
arch/arm/dts/versal-mini-emmc1.dts | 1 -
arch/arm/dts/zynqmp-mini-emmc0.dts | 1 -
arch/arm/dts/zynqmp-mini-emmc1.dts | 1 -
arch/arm/dts/zynqmp.dtsi | 2 --
5 files changed, 6 deletions(-)
diff --git a/arch/arm/dts/versal-mini-emmc0.dts b/arch/arm/dts/versal-mini-emmc0.dts
index 7c81a82fb9..d098c2d01b 100644
--- a/arch/arm/dts/versal-mini-emmc0.dts
+++ b/arch/arm/dts/versal-mini-emmc0.dts
@@ -44,7 +44,6 @@
reg = <0x0 0xf1040000 0x0 0x10000>;
clock-names = "clk_xin", "clk_ahb";
clocks = <&clk200 &clk200>;
- xlnx,device_id = <0>;
no-1-8-v;
xlnx,mio-bank = <0>;
};
diff --git a/arch/arm/dts/versal-mini-emmc1.dts b/arch/arm/dts/versal-mini-emmc1.dts
index bf7569d4cc..9d4ac28359 100644
--- a/arch/arm/dts/versal-mini-emmc1.dts
+++ b/arch/arm/dts/versal-mini-emmc1.dts
@@ -44,7 +44,6 @@
reg = <0x0 0xf1050000 0x0 0x10000>;
clock-names = "clk_xin", "clk_ahb";
clocks = <&clk200 &clk200>;
- xlnx,device_id = <1>;
no-1-8-v;
xlnx,mio-bank = <0>;
};
diff --git a/arch/arm/dts/zynqmp-mini-emmc0.dts b/arch/arm/dts/zynqmp-mini-emmc0.dts
index 8467dd8e1c..1cc4ade5e8 100644
--- a/arch/arm/dts/zynqmp-mini-emmc0.dts
+++ b/arch/arm/dts/zynqmp-mini-emmc0.dts
@@ -56,7 +56,6 @@
reg = <0x0 0xff160000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
clocks = <&clk_xin &clk_xin>;
- xlnx,device_id = <0>;
};
};
};
diff --git a/arch/arm/dts/zynqmp-mini-emmc1.dts b/arch/arm/dts/zynqmp-mini-emmc1.dts
index 2afcc7751b..96b5dc2932 100644
--- a/arch/arm/dts/zynqmp-mini-emmc1.dts
+++ b/arch/arm/dts/zynqmp-mini-emmc1.dts
@@ -56,7 +56,6 @@
reg = <0x0 0xff170000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
clocks = <&clk_xin &clk_xin>;
- xlnx,device_id = <1>;
};
};
};
diff --git a/arch/arm/dts/zynqmp.dtsi b/arch/arm/dts/zynqmp.dtsi
index fbc6e752da..2fbd0f711b 100644
--- a/arch/arm/dts/zynqmp.dtsi
+++ b/arch/arm/dts/zynqmp.dtsi
@@ -720,7 +720,6 @@
interrupts = <0 48 4>;
reg = <0x0 0xff160000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
- xlnx,device_id = <0>;
iommus = <&smmu 0x870>;
#clock-cells = <1>;
clock-output-names = "clk_out_sd0", "clk_in_sd0";
@@ -736,7 +735,6 @@
interrupts = <0 49 4>;
reg = <0x0 0xff170000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
- xlnx,device_id = <1>;
iommus = <&smmu 0x871>;
#clock-cells = <1>;
clock-output-names = "clk_out_sd1", "clk_in_sd1";
--
2.17.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls
2022-09-30 9:25 [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Ashok Reddy Soma
` (2 preceding siblings ...)
2022-09-30 9:25 ` [PATCH 3/3] arm64: dts: Remove unused property device_id Ashok Reddy Soma
@ 2022-10-04 12:42 ` Michal Simek
3 siblings, 0 replies; 9+ messages in thread
From: Michal Simek @ 2022-10-04 12:42 UTC (permalink / raw)
To: Ashok Reddy Soma, u-boot
Cc: peng.fan, jh80.chung, ayankuma, piyush.mehta,
lakshmi.sai.krishna.potthuri, shravya.kumbham
On 9/30/22 11:25, Ashok Reddy Soma wrote:
> In this patch series
> - Existing node_id is u8, change it to u32 to accommodate Versal node_id
> - Read "power-domains" id from DT and use in all firmware calls in place
> of node_id.
> - Remove static values of node_id which are set based on "device_id"
> - Remove "xlnx,device_id" from all dts files
>
>
> Ashok Reddy Soma (3):
> mmc: zynq_sdhci: Change node_id prototype to u32
> mmc: zynq_sdhci: Read power-domains id from DT and use
> arm64: dts: Remove unused property device_id
>
> arch/arm/dts/versal-mini-emmc0.dts | 1 -
> arch/arm/dts/versal-mini-emmc1.dts | 1 -
> arch/arm/dts/zynqmp-mini-emmc0.dts | 1 -
> arch/arm/dts/zynqmp-mini-emmc1.dts | 1 -
> arch/arm/dts/zynqmp.dtsi | 2 --
> drivers/mmc/zynq_sdhci.c | 53 +++++++++++++++---------------
> 6 files changed, 27 insertions(+), 32 deletions(-)
>
Applied.
M
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
2022-09-30 9:25 ` [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32 Ashok Reddy Soma
@ 2022-10-07 12:45 ` Jaehoon Chung
2022-10-12 6:27 ` Soma, Ashok Reddy
0 siblings, 1 reply; 9+ messages in thread
From: Jaehoon Chung @ 2022-10-07 12:45 UTC (permalink / raw)
To: Ashok Reddy Soma, u-boot
Cc: michal.simek, peng.fan, jh80.chung, ayankuma, piyush.mehta,
lakshmi.sai.krishna.potthuri, shravya.kumbham
On 9/30/22 18:25, Ashok Reddy Soma wrote:
> In Versal platform power domain node_id is bigger than u8, hence
> change prototype to u32 to accommodate. Change u8 to u32 in the function
> prototypes that use node_id and remove casting to u32 from
> xilinx_pm_request() call parameters.
>
> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
> ---
>
> drivers/mmc/zynq_sdhci.c | 14 +++++++-------
> 1 file changed, 7 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c
> index 8f4071c8c2..3a4194452c 100644
> --- a/drivers/mmc/zynq_sdhci.c
> +++ b/drivers/mmc/zynq_sdhci.c
> @@ -111,7 +111,7 @@ static const u8 mode2timing[] = {
> [MMC_HS_200] = MMC_TIMING_MMC_HS200,
> };
>
> -static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> +static inline int arasan_zynqmp_set_in_tapdelay(u32 node_id, u32 itap_delay)
Is it passed by u8 from sdhci_zynqmp_sampleclk_set_pahse()?
Best Regards,
Jaehoon Chung
> {
> int ret;
>
> @@ -155,7 +155,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> if (ret)
> return ret;
> } else {
> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> + return xilinx_pm_request(PM_IOCTL, node_id,
> IOCTL_SET_SD_TAPDELAY,
> PM_TAPDELAY_INPUT, itap_delay, NULL);
> }
> @@ -163,7 +163,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> return 0;
> }
>
> -static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32 otap_delay)
> +static inline int arasan_zynqmp_set_out_tapdelay(u32 node_id, u32 otap_delay)
> {
> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
> if (node_id == NODE_SD_0)
> @@ -174,13 +174,13 @@ static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32 otap_delay)
> return zynqmp_mmio_write(SD_OTAP_DLY, SD1_OTAPDLYSEL_MASK,
> (otap_delay << 16));
> } else {
> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> + return xilinx_pm_request(PM_IOCTL, node_id,
> IOCTL_SET_SD_TAPDELAY,
> PM_TAPDELAY_OUTPUT, otap_delay, NULL);
> }
> }
>
> -static inline int zynqmp_dll_reset(u8 node_id, u32 type)
> +static inline int zynqmp_dll_reset(u32 node_id, u32 type)
> {
> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
> if (node_id == NODE_SD_0)
> @@ -192,12 +192,12 @@ static inline int zynqmp_dll_reset(u8 node_id, u32 type)
> type == PM_DLL_RESET_ASSERT ?
> SD1_DLL_RST : 0);
> } else {
> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> + return xilinx_pm_request(PM_IOCTL, node_id,
> IOCTL_SD_DLL_RESET, type, 0, NULL);
> }
> }
>
> -static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u8 node_id)
> +static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u32 node_id)
> {
> struct mmc *mmc = (struct mmc *)host->mmc;
> struct udevice *dev = mmc->dev;
^ permalink raw reply [flat|nested] 9+ messages in thread
* RE: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
2022-10-07 12:45 ` Jaehoon Chung
@ 2022-10-12 6:27 ` Soma, Ashok Reddy
2022-10-12 9:39 ` 정재훈
0 siblings, 1 reply; 9+ messages in thread
From: Soma, Ashok Reddy @ 2022-10-12 6:27 UTC (permalink / raw)
To: Jaehoon Chung, u-boot
Cc: Simek, Michal, peng.fan, jh80.chung, Halder, Ayan Kumar, Mehta,
Piyush, lakshmi.sai.krishna.potthuri, shravya.kumbham
Hi Jaehoon,
>-----Original Message-----
>From: Jaehoon Chung <jh80.chung@gmail.com>
>Sent: Friday, October 7, 2022 6:16 PM
>To: Soma, Ashok Reddy <ashok.reddy.soma@amd.com>; u-boot@lists.denx.de
>Cc: Simek, Michal <michal.simek@amd.com>; peng.fan@nxp.com; jh80.chung@samsung.com; Halder, Ayan Kumar <ayan.kumar.halder@amd.com>; Mehta, Piyush <piyush.mehta@amd.com>; lakshmi.sai.krishna.potthuri@amd.com; shravya.kumbham@amd.com
>Subject: Re: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
>
>
>
>On 9/30/22 18:25, Ashok Reddy Soma wrote:
>> In Versal platform power domain node_id is bigger than u8, hence
>> change prototype to u32 to accommodate. Change u8 to u32 in the
>> function prototypes that use node_id and remove casting to u32 from
>> xilinx_pm_request() call parameters.
>>
>> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
>> ---
>>
>> drivers/mmc/zynq_sdhci.c | 14 +++++++-------
>> 1 file changed, 7 insertions(+), 7 deletions(-)
>>
>> diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c index
>> 8f4071c8c2..3a4194452c 100644
>> --- a/drivers/mmc/zynq_sdhci.c
>> +++ b/drivers/mmc/zynq_sdhci.c
>> @@ -111,7 +111,7 @@ static const u8 mode2timing[] = {
>> [MMC_HS_200] = MMC_TIMING_MMC_HS200, };
>>
>> -static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32
>> itap_delay)
>> +static inline int arasan_zynqmp_set_in_tapdelay(u32 node_id, u32
>> +itap_delay)
>
>Is it passed by u8 from sdhci_zynqmp_sampleclk_set_pahse()?
Seems like I missed to change the type to u32 from where these functions are called. But those lines are removed in patch 2/3.
Should I send V2 or is it okay ?
Thanks,
Ashok
>
>
>Best Regards,
>Jaehoon Chung
>
>> {
>> int ret;
>>
>> @@ -155,7 +155,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
>> if (ret)
>> return ret;
>> } else {
>> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
>> + return xilinx_pm_request(PM_IOCTL, node_id,
>> IOCTL_SET_SD_TAPDELAY,
>> PM_TAPDELAY_INPUT, itap_delay, NULL);
>> }
>> @@ -163,7 +163,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
>> return 0;
>> }
>>
>> -static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32
>> otap_delay)
>> +static inline int arasan_zynqmp_set_out_tapdelay(u32 node_id, u32
>> +otap_delay)
>> {
>> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
>> if (node_id == NODE_SD_0)
>> @@ -174,13 +174,13 @@ static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32 otap_delay)
>> return zynqmp_mmio_write(SD_OTAP_DLY, SD1_OTAPDLYSEL_MASK,
>> (otap_delay << 16));
>> } else {
>> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
>> + return xilinx_pm_request(PM_IOCTL, node_id,
>> IOCTL_SET_SD_TAPDELAY,
>> PM_TAPDELAY_OUTPUT, otap_delay, NULL);
>> }
>> }
>>
>> -static inline int zynqmp_dll_reset(u8 node_id, u32 type)
>> +static inline int zynqmp_dll_reset(u32 node_id, u32 type)
>> {
>> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
>> if (node_id == NODE_SD_0)
>> @@ -192,12 +192,12 @@ static inline int zynqmp_dll_reset(u8 node_id, u32 type)
>> type == PM_DLL_RESET_ASSERT ?
>> SD1_DLL_RST : 0);
>> } else {
>> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
>> + return xilinx_pm_request(PM_IOCTL, node_id,
>> IOCTL_SD_DLL_RESET, type, 0, NULL);
>> }
>> }
>>
>> -static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u8
>> node_id)
>> +static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u32
>> +node_id)
>> {
>> struct mmc *mmc = (struct mmc *)host->mmc;
>> struct udevice *dev = mmc->dev;
^ permalink raw reply [flat|nested] 9+ messages in thread
* RE: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
2022-10-12 6:27 ` Soma, Ashok Reddy
@ 2022-10-12 9:39 ` 정재훈
2022-10-12 10:34 ` Soma, Ashok Reddy
0 siblings, 1 reply; 9+ messages in thread
From: 정재훈 @ 2022-10-12 9:39 UTC (permalink / raw)
To: 'Soma, Ashok Reddy', 'Jaehoon Chung', u-boot
Cc: 'Simek, Michal', peng.fan, 'Halder, Ayan Kumar',
'Mehta, Piyush',
lakshmi.sai.krishna.potthuri, shravya.kumbham
Hi,
> -----Original Message-----
> From: Soma, Ashok Reddy [mailto:ashok.reddy.soma@amd.com]
> Sent: Wednesday, October 12, 2022 3:27 PM
> To: Jaehoon Chung <jh80.chung@gmail.com>; u-boot@lists.denx.de
> Cc: Simek, Michal <michal.simek@amd.com>; peng.fan@nxp.com; jh80.chung@samsung.com; Halder, Ayan
> Kumar <ayan.kumar.halder@amd.com>; Mehta, Piyush <piyush.mehta@amd.com>;
> lakshmi.sai.krishna.potthuri@amd.com; shravya.kumbham@amd.com
> Subject: RE: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
>
> Hi Jaehoon,
>
> >-----Original Message-----
> >From: Jaehoon Chung <jh80.chung@gmail.com>
> >Sent: Friday, October 7, 2022 6:16 PM
> >To: Soma, Ashok Reddy <ashok.reddy.soma@amd.com>; u-boot@lists.denx.de
> >Cc: Simek, Michal <michal.simek@amd.com>; peng.fan@nxp.com; jh80.chung@samsung.com; Halder, Ayan
> Kumar <ayan.kumar.halder@amd.com>; Mehta, Piyush <piyush.mehta@amd.com>;
> lakshmi.sai.krishna.potthuri@amd.com; shravya.kumbham@amd.com
> >Subject: Re: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
> >
> >
> >
> >On 9/30/22 18:25, Ashok Reddy Soma wrote:
> >> In Versal platform power domain node_id is bigger than u8, hence
> >> change prototype to u32 to accommodate. Change u8 to u32 in the
> >> function prototypes that use node_id and remove casting to u32 from
> >> xilinx_pm_request() call parameters.
> >>
> >> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
> >> ---
> >>
> >> drivers/mmc/zynq_sdhci.c | 14 +++++++-------
> >> 1 file changed, 7 insertions(+), 7 deletions(-)
> >>
> >> diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c index
> >> 8f4071c8c2..3a4194452c 100644
> >> --- a/drivers/mmc/zynq_sdhci.c
> >> +++ b/drivers/mmc/zynq_sdhci.c
> >> @@ -111,7 +111,7 @@ static const u8 mode2timing[] = {
> >> [MMC_HS_200] = MMC_TIMING_MMC_HS200, };
> >>
> >> -static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32
> >> itap_delay)
> >> +static inline int arasan_zynqmp_set_in_tapdelay(u32 node_id, u32
> >> +itap_delay)
> >
> >Is it passed by u8 from sdhci_zynqmp_sampleclk_set_pahse()?
>
> Seems like I missed to change the type to u32 from where these functions are called. But those
> lines are removed in patch 2/3.
> Should I send V2 or is it okay ?
I think that it doesn't need to resend V2. As you mentioned, it's removed on patch 2/3.
And it was already applied. Sorry for reviewed too late.
Thanks!
Best Regards,
Jaehoon Chung
>
> Thanks,
> Ashok
> >
> >
> >Best Regards,
> >Jaehoon Chung
> >
> >> {
> >> int ret;
> >>
> >> @@ -155,7 +155,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> >> if (ret)
> >> return ret;
> >> } else {
> >> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> >> + return xilinx_pm_request(PM_IOCTL, node_id,
> >> IOCTL_SET_SD_TAPDELAY,
> >> PM_TAPDELAY_INPUT, itap_delay, NULL);
> >> }
> >> @@ -163,7 +163,7 @@ static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> >> return 0;
> >> }
> >>
> >> -static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32
> >> otap_delay)
> >> +static inline int arasan_zynqmp_set_out_tapdelay(u32 node_id, u32
> >> +otap_delay)
> >> {
> >> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
> >> if (node_id == NODE_SD_0)
> >> @@ -174,13 +174,13 @@ static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32
> otap_delay)
> >> return zynqmp_mmio_write(SD_OTAP_DLY, SD1_OTAPDLYSEL_MASK,
> >> (otap_delay << 16));
> >> } else {
> >> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> >> + return xilinx_pm_request(PM_IOCTL, node_id,
> >> IOCTL_SET_SD_TAPDELAY,
> >> PM_TAPDELAY_OUTPUT, otap_delay, NULL);
> >> }
> >> }
> >>
> >> -static inline int zynqmp_dll_reset(u8 node_id, u32 type)
> >> +static inline int zynqmp_dll_reset(u32 node_id, u32 type)
> >> {
> >> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
> >> if (node_id == NODE_SD_0)
> >> @@ -192,12 +192,12 @@ static inline int zynqmp_dll_reset(u8 node_id, u32 type)
> >> type == PM_DLL_RESET_ASSERT ?
> >> SD1_DLL_RST : 0);
> >> } else {
> >> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> >> + return xilinx_pm_request(PM_IOCTL, node_id,
> >> IOCTL_SD_DLL_RESET, type, 0, NULL);
> >> }
> >> }
> >>
> >> -static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u8
> >> node_id)
> >> +static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u32
> >> +node_id)
> >> {
> >> struct mmc *mmc = (struct mmc *)host->mmc;
> >> struct udevice *dev = mmc->dev;
^ permalink raw reply [flat|nested] 9+ messages in thread
* RE: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
2022-10-12 9:39 ` 정재훈
@ 2022-10-12 10:34 ` Soma, Ashok Reddy
0 siblings, 0 replies; 9+ messages in thread
From: Soma, Ashok Reddy @ 2022-10-12 10:34 UTC (permalink / raw)
To: 정재훈, 'Jaehoon Chung', u-boot
Cc: Simek, Michal, peng.fan, Halder, Ayan Kumar, Mehta, Piyush,
lakshmi.sai.krishna.potthuri, shravya.kumbham
Hi Jaehoon,
> -----Original Message-----
> From: 정재훈 <jh80.chung@samsung.com>
> Sent: Wednesday, October 12, 2022 3:09 PM
> To: Soma, Ashok Reddy <ashok.reddy.soma@amd.com>; 'Jaehoon Chung'
> <jh80.chung@gmail.com>; u-boot@lists.denx.de
> Cc: Simek, Michal <michal.simek@amd.com>; peng.fan@nxp.com; Halder,
> Ayan Kumar <ayan.kumar.halder@amd.com>; Mehta, Piyush
> <piyush.mehta@amd.com>; lakshmi.sai.krishna.potthuri@amd.com;
> shravya.kumbham@amd.com
> Subject: RE: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32
>
> Hi,
>
> > -----Original Message-----
> > From: Soma, Ashok Reddy [mailto:ashok.reddy.soma@amd.com]
> > Sent: Wednesday, October 12, 2022 3:27 PM
> > To: Jaehoon Chung <jh80.chung@gmail.com>; u-boot@lists.denx.de
> > Cc: Simek, Michal <michal.simek@amd.com>; peng.fan@nxp.com;
> > jh80.chung@samsung.com; Halder, Ayan Kumar
> > <ayan.kumar.halder@amd.com>; Mehta, Piyush
> <piyush.mehta@amd.com>;
> > lakshmi.sai.krishna.potthuri@amd.com; shravya.kumbham@amd.com
> > Subject: RE: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to
> > u32
> >
> > Hi Jaehoon,
> >
> > >-----Original Message-----
> > >From: Jaehoon Chung <jh80.chung@gmail.com>
> > >Sent: Friday, October 7, 2022 6:16 PM
> > >To: Soma, Ashok Reddy <ashok.reddy.soma@amd.com>;
> > >u-boot@lists.denx.de
> > >Cc: Simek, Michal <michal.simek@amd.com>; peng.fan@nxp.com;
> > >jh80.chung@samsung.com; Halder, Ayan
> > Kumar <ayan.kumar.halder@amd.com>; Mehta, Piyush
> > <piyush.mehta@amd.com>; lakshmi.sai.krishna.potthuri@amd.com;
> > shravya.kumbham@amd.com
> > >Subject: Re: [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to
> > >u32
> > >
> > >
> > >
> > >On 9/30/22 18:25, Ashok Reddy Soma wrote:
> > >> In Versal platform power domain node_id is bigger than u8, hence
> > >> change prototype to u32 to accommodate. Change u8 to u32 in the
> > >> function prototypes that use node_id and remove casting to u32 from
> > >> xilinx_pm_request() call parameters.
> > >>
> > >> Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
> > >> ---
> > >>
> > >> drivers/mmc/zynq_sdhci.c | 14 +++++++-------
> > >> 1 file changed, 7 insertions(+), 7 deletions(-)
> > >>
> > >> diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c
> > >> index 8f4071c8c2..3a4194452c 100644
> > >> --- a/drivers/mmc/zynq_sdhci.c
> > >> +++ b/drivers/mmc/zynq_sdhci.c
> > >> @@ -111,7 +111,7 @@ static const u8 mode2timing[] = {
> > >> [MMC_HS_200] = MMC_TIMING_MMC_HS200, };
> > >>
> > >> -static inline int arasan_zynqmp_set_in_tapdelay(u8 node_id, u32
> > >> itap_delay)
> > >> +static inline int arasan_zynqmp_set_in_tapdelay(u32 node_id, u32
> > >> +itap_delay)
> > >
> > >Is it passed by u8 from sdhci_zynqmp_sampleclk_set_pahse()?
> >
> > Seems like I missed to change the type to u32 from where these
> > functions are called. But those lines are removed in patch 2/3.
> > Should I send V2 or is it okay ?
>
> I think that it doesn't need to resend V2. As you mentioned, it's removed on
> patch 2/3.
> And it was already applied. Sorry for reviewed too late.
Never mind about the timing, it was a good catch. thanks for the review.
Thanks,
Ashok
>
> Thanks!
>
> Best Regards,
> Jaehoon Chung
>
> >
> > Thanks,
> > Ashok
> > >
> > >
> > >Best Regards,
> > >Jaehoon Chung
> > >
> > >> {
> > >> int ret;
> > >>
> > >> @@ -155,7 +155,7 @@ static inline int
> arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> > >> if (ret)
> > >> return ret;
> > >> } else {
> > >> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> > >> + return xilinx_pm_request(PM_IOCTL, node_id,
> > >> IOCTL_SET_SD_TAPDELAY,
> > >> PM_TAPDELAY_INPUT, itap_delay,
> NULL);
> > >> }
> > >> @@ -163,7 +163,7 @@ static inline int
> arasan_zynqmp_set_in_tapdelay(u8 node_id, u32 itap_delay)
> > >> return 0;
> > >> }
> > >>
> > >> -static inline int arasan_zynqmp_set_out_tapdelay(u8 node_id, u32
> > >> otap_delay)
> > >> +static inline int arasan_zynqmp_set_out_tapdelay(u32 node_id, u32
> > >> +otap_delay)
> > >> {
> > >> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
> > >> if (node_id == NODE_SD_0)
> > >> @@ -174,13 +174,13 @@ static inline int
> > >> arasan_zynqmp_set_out_tapdelay(u8 node_id, u32
> > otap_delay)
> > >> return zynqmp_mmio_write(SD_OTAP_DLY,
> SD1_OTAPDLYSEL_MASK,
> > >> (otap_delay << 16));
> > >> } else {
> > >> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> > >> + return xilinx_pm_request(PM_IOCTL, node_id,
> > >> IOCTL_SET_SD_TAPDELAY,
> > >> PM_TAPDELAY_OUTPUT, otap_delay,
> NULL);
> > >> }
> > >> }
> > >>
> > >> -static inline int zynqmp_dll_reset(u8 node_id, u32 type)
> > >> +static inline int zynqmp_dll_reset(u32 node_id, u32 type)
> > >> {
> > >> if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) {
> > >> if (node_id == NODE_SD_0)
> > >> @@ -192,12 +192,12 @@ static inline int zynqmp_dll_reset(u8 node_id,
> u32 type)
> > >> type == PM_DLL_RESET_ASSERT ?
> > >> SD1_DLL_RST : 0);
> > >> } else {
> > >> - return xilinx_pm_request(PM_IOCTL, (u32)node_id,
> > >> + return xilinx_pm_request(PM_IOCTL, node_id,
> > >> IOCTL_SD_DLL_RESET, type, 0, NULL);
> > >> }
> > >> }
> > >>
> > >> -static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u8
> > >> node_id)
> > >> +static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u32
> > >> +node_id)
> > >> {
> > >> struct mmc *mmc = (struct mmc *)host->mmc;
> > >> struct udevice *dev = mmc->dev;
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2022-10-12 10:35 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-30 9:25 [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 1/3] mmc: zynq_sdhci: Change node_id prototype to u32 Ashok Reddy Soma
2022-10-07 12:45 ` Jaehoon Chung
2022-10-12 6:27 ` Soma, Ashok Reddy
2022-10-12 9:39 ` 정재훈
2022-10-12 10:34 ` Soma, Ashok Reddy
2022-09-30 9:25 ` [PATCH 2/3] mmc: zynq_sdhci: Read power-domains id from DT and use Ashok Reddy Soma
2022-09-30 9:25 ` [PATCH 3/3] arm64: dts: Remove unused property device_id Ashok Reddy Soma
2022-10-04 12:42 ` [PATCH 0/3] Read mmc "power-domains" id from DT and use for firmware calls Michal Simek
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.