* [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
This adds:
- Device bindings
- Initial device DT
This serie depends on:
- https://lore.kernel.org/all/20221025-rk808-multi-v2-0-d292d51ada81@linaro.org/
To: Sebastian Reichel <sre@kernel.org>
To: Rob Herring <robh+dt@kernel.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
To: Kevin Hilman <khilman@baylibre.com>
To: Jerome Brunet <jbrunet@baylibre.com>
To: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v2:
- Dropped power off driver/bindings, will move to another patchset
- Fixed DT comments from Krzysztof
- Dropped poweroff node
- Add Acked-by from Rob to bindings change
- Link to v1: https://lore.kernel.org/r/20221031-b4-odroid-go-ultra-initial-v1-0-42e3dbea86d5@linaro.org
---
Neil Armstrong (2):
dt-bindings: amlogic: document Odroid Go Ultra compatible
arm64: dts: amlogic: add initial Odroid Go Ultra DTS
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
3 files changed, 724 insertions(+)
---
base-commit: 2c3c398ddfabf48b7a0b66b5f01052ba43c36337
change-id: 20221031-b4-odroid-go-ultra-initial-5e65cde5e23a
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
This adds:
- Device bindings
- Initial device DT
This serie depends on:
- https://lore.kernel.org/all/20221025-rk808-multi-v2-0-d292d51ada81@linaro.org/
To: Sebastian Reichel <sre@kernel.org>
To: Rob Herring <robh+dt@kernel.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
To: Kevin Hilman <khilman@baylibre.com>
To: Jerome Brunet <jbrunet@baylibre.com>
To: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v2:
- Dropped power off driver/bindings, will move to another patchset
- Fixed DT comments from Krzysztof
- Dropped poweroff node
- Add Acked-by from Rob to bindings change
- Link to v1: https://lore.kernel.org/r/20221031-b4-odroid-go-ultra-initial-v1-0-42e3dbea86d5@linaro.org
---
Neil Armstrong (2):
dt-bindings: amlogic: document Odroid Go Ultra compatible
arm64: dts: amlogic: add initial Odroid Go Ultra DTS
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
3 files changed, 724 insertions(+)
---
base-commit: 2c3c398ddfabf48b7a0b66b5f01052ba43c36337
change-id: 20221031-b4-odroid-go-ultra-initial-5e65cde5e23a
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
This adds:
- Device bindings
- Initial device DT
This serie depends on:
- https://lore.kernel.org/all/20221025-rk808-multi-v2-0-d292d51ada81@linaro.org/
To: Sebastian Reichel <sre@kernel.org>
To: Rob Herring <robh+dt@kernel.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
To: Kevin Hilman <khilman@baylibre.com>
To: Jerome Brunet <jbrunet@baylibre.com>
To: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v2:
- Dropped power off driver/bindings, will move to another patchset
- Fixed DT comments from Krzysztof
- Dropped poweroff node
- Add Acked-by from Rob to bindings change
- Link to v1: https://lore.kernel.org/r/20221031-b4-odroid-go-ultra-initial-v1-0-42e3dbea86d5@linaro.org
---
Neil Armstrong (2):
dt-bindings: amlogic: document Odroid Go Ultra compatible
arm64: dts: amlogic: add initial Odroid Go Ultra DTS
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
3 files changed, 724 insertions(+)
---
base-commit: 2c3c398ddfabf48b7a0b66b5f01052ba43c36337
change-id: 20221031-b4-odroid-go-ultra-initial-5e65cde5e23a
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible
2022-11-18 15:50 ` Neil Armstrong
(?)
@ 2022-11-18 15:50 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This documents the Odroid Go Ultra, a portable gaming device,
with the following characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 9fda2436c618..e16b5fa55847 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -163,6 +163,7 @@ properties:
- azw,gsking-x
- azw,gtking
- azw,gtking-pro
+ - hardkernel,odroid-go-ultra
- hardkernel,odroid-n2
- hardkernel,odroid-n2-plus
- khadas,vim3
--
b4 0.10.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This documents the Odroid Go Ultra, a portable gaming device,
with the following characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 9fda2436c618..e16b5fa55847 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -163,6 +163,7 @@ properties:
- azw,gsking-x
- azw,gtking
- azw,gtking-pro
+ - hardkernel,odroid-go-ultra
- hardkernel,odroid-n2
- hardkernel,odroid-n2-plus
- khadas,vim3
--
b4 0.10.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This documents the Odroid Go Ultra, a portable gaming device,
with the following characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 9fda2436c618..e16b5fa55847 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -163,6 +163,7 @@ properties:
- azw,gsking-x
- azw,gtking
- azw,gtking-pro
+ - hardkernel,odroid-go-ultra
- hardkernel,odroid-n2
- hardkernel,odroid-n2-plus
- khadas,vim3
--
b4 0.10.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
2022-11-18 15:50 ` Neil Armstrong
(?)
@ 2022-11-18 15:50 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
2 files changed, 723 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e213aeebb774..97b42e2100e0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
new file mode 100644
index 000000000000..1e40709610c5
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
@@ -0,0 +1,722 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "hardkernel,odroid-go-ultra", "amlogic,s922x", "amlogic,g12b";
+ model = "Hardkernel ODROID-GO-Ultra";
+
+ aliases {
+ serial0 = &uart_AO;
+ rtc0 = &vrtc;
+ };
+
+ adc-joystick-left {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 2>, <&saradc 3>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_Y>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_X>;
+ abs-range = <700 2900>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ adc-joystick-right {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 0>, <&saradc 1>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_RY>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_RX>;
+ abs-range = <800 3000>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ codec_clk: codec-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ clock-output-names = "codec_clk";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <10>;
+ pinctrl-0 = <&keypad_gpio_pins>;
+ pinctrl-names = "default";
+
+ volume-up-button {
+ label = "VOLUME-UP";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&gpio GPIOX_8 GPIO_ACTIVE_LOW>;
+ };
+ volume-down-button {
+ label = "VOLUME-DOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&gpio GPIOX_9 GPIO_ACTIVE_LOW>;
+ };
+ dpad-up-button {
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ gpios = <&gpio GPIOX_0 GPIO_ACTIVE_LOW>;
+ };
+ dpad-down-button {
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ gpios = <&gpio GPIOX_1 GPIO_ACTIVE_LOW>;
+ };
+ dpad-left-button {
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ gpios = <&gpio GPIOX_2 GPIO_ACTIVE_LOW>;
+ };
+ dpad-right-button {
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ gpios = <&gpio GPIOX_3 GPIO_ACTIVE_LOW>;
+ };
+ a-button {
+ label = "A";
+ linux,code = <BTN_EAST>;
+ gpios = <&gpio GPIOX_4 GPIO_ACTIVE_LOW>;
+ };
+ b-button {
+ label = "B";
+ linux,code = <BTN_SOUTH>;
+ gpios = <&gpio GPIOX_5 GPIO_ACTIVE_LOW>;
+ };
+ y-button {
+ label = "Y";
+ linux,code = <BTN_WEST>;
+ gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ };
+ x-button {
+ label = "X";
+ linux,code = <BTN_NORTH>;
+ gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ };
+ f1-button {
+ label = "F1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ gpios = <&gpio GPIOX_17 GPIO_ACTIVE_LOW>;
+ };
+ f2-button {
+ label = "F2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+ };
+ f3-button {
+ label = "F3";
+ linux,code = <BTN_TRIGGER_HAPPY3>;
+ gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>;
+ };
+ f4-button {
+ label = "F4";
+ linux,code = <BTN_TRIGGER_HAPPY4>;
+ gpios = <&gpio GPIOX_12 GPIO_ACTIVE_LOW>;
+ };
+ f5-button {
+ label = "F5";
+ linux,code = <BTN_TRIGGER_HAPPY5>;
+ gpios = <&gpio GPIOX_13 GPIO_ACTIVE_LOW>;
+ };
+ f6-button {
+ label = "F6";
+ linux,code = <BTN_TRIGGER_HAPPY6>;
+ gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>;
+ };
+ top-left-button {
+ label = "TOP Left";
+ linux,code = <BTN_TL>;
+ gpios = <&gpio GPIOX_14 GPIO_ACTIVE_LOW>;
+ };
+ top-left2-button {
+ label = "TOP Left 2";
+ linux,code = <BTN_TL2>;
+ gpios = <&gpio GPIOX_19 GPIO_ACTIVE_LOW>;
+ };
+ top-right-button {
+ label = "TOP Right";
+ linux,code = <BTN_TR>;
+ gpios = <&gpio GPIOX_15 GPIO_ACTIVE_LOW>;
+ };
+ top-right2-button {
+ label = "TOP Right 2";
+ linux,code = <BTN_TR2>;
+ gpios = <&gpio GPIOX_18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vdd_sys: regulator-vdd-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_SYS";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "Odroid GO Ultra";
+ audio-widgets = "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+ audio-aux-devs = <&tdmout_b>, <&tdmin_b>, <&speaker_amp>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TDMIN_B IN 1", "TDM_B Capture",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "MICL", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Internal Speakers", "Speaker Amplifier OUTL",
+ "Internal Speakers", "Speaker Amplifier OUTR";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&rk817>;
+ };
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&hp_5v>;
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+/* RK817 only supports 12.5mV steps, round up the values */
+&cpu_opp_table_0 {
+ opp-1000000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <762500>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <837500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1896000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1992000000 {
+ opp-microvolt = <1012500>;
+ };
+};
+
+/* RK818 only supports 12.5mV steps, round up the values */
+&cpub_opp_table_1 {
+ opp-1000000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <825000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <900000>;
+ };
+ opp-1800000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1908000000 {
+ opp-microvolt = <1025000>;
+ };
+};
+
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>;
+ pinctrl-names = "default";
+
+ rk818: pmic@1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_7 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vcc_2v3>;
+ vcc8-supply = <&vcc_2v3>;
+ vcc9-supply = <&vddao_3v3>;
+ boost-supply = <&vdd_sys>;
+ switch-supply = <&vdd_sys>;
+
+ regulators {
+ vddcpu_a: DCDC_REG1 {
+ regulator-name = "vddcpu_a";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <775000>;
+ regulator-max-microvolt = <1025000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <775000>;
+ };
+ };
+
+ vdd_ee: DCDC_REG2 {
+ regulator-name = "vdd_ee";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <875000>;
+ };
+ };
+
+ vddq_1v1: DCDC_REG3 {
+ regulator-name = "vddq_1v1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vddao_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddao_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ hp_5v: DCDC_BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "hp_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vddio_ao1v8: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddio_ao1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddq_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddq_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddio_c: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddio_c";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_sd: SWITCH_REG {
+ regulator-name = "vcc_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio_intc>;
+
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_5 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc5-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_sys>;
+ vcc8-supply = <&vdd_sys>;
+ vcc9-supply = <&rk817_boost>;
+
+ #sound-dai-cells = <0>;
+ clocks = <&codec_clk>;
+ clock-names = "mclk";
+
+ #clock-cells = <1>;
+
+ regulators {
+ vddcpu_b: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <737500>;
+ regulator-max-microvolt = <1012500>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vddcpu_b";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_2v3: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <2400000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_2v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_lcd: LDO_REG8 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "rk817_boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ usb_host: OTG_SWITCH {
+ regulator-name = "usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+ð_phy {
+ status = "disabled";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&periphs_pinctrl {
+ keypad_gpio_pins: keypad-gpio {
+ mux {
+ groups = "GPIOX_0", "GPIOX_1", "GPIOX_2", "GPIOX_3",
+ "GPIOX_4", "GPIOX_5", "GPIOX_6", "GPIOX_7",
+ "GPIOX_8", "GPIOX_9", "GPIOX_10", "GPIOX_11",
+ "GPIOX_12", "GPIOX_13", "GPIOX_14", "GPIOX_15",
+ "GPIOX_16", "GPIOX_17", "GPIOX_18", "GPIOX_19";
+ function = "gpio_periphs";
+ bias-pull-up;
+ output-disable;
+ };
+ };
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_c>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_ao1v8>;
+};
+
+
+&tdmif_b {
+ pinctrl-0 = <&tdm_b_dout0_pins>, <&tdm_b_fs_pins>, <&tdm_b_sclk_pins>, <&tdm_b_din1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ assigned-clocks = <&clkc_audio AUD_CLKID_TDM_SCLK_PAD1>,
+ <&clkc_audio AUD_CLKID_TDM_LRCLK_PAD1>;
+ assigned-clock-parents = <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ assigned-clock-rates = <0>, <0>;
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usb2_phy0 {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ status = "okay";
+ phy-supply = <&usb_host>;
+};
--
b4 0.10.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
2 files changed, 723 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e213aeebb774..97b42e2100e0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
new file mode 100644
index 000000000000..1e40709610c5
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
@@ -0,0 +1,722 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "hardkernel,odroid-go-ultra", "amlogic,s922x", "amlogic,g12b";
+ model = "Hardkernel ODROID-GO-Ultra";
+
+ aliases {
+ serial0 = &uart_AO;
+ rtc0 = &vrtc;
+ };
+
+ adc-joystick-left {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 2>, <&saradc 3>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_Y>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_X>;
+ abs-range = <700 2900>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ adc-joystick-right {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 0>, <&saradc 1>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_RY>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_RX>;
+ abs-range = <800 3000>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ codec_clk: codec-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ clock-output-names = "codec_clk";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <10>;
+ pinctrl-0 = <&keypad_gpio_pins>;
+ pinctrl-names = "default";
+
+ volume-up-button {
+ label = "VOLUME-UP";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&gpio GPIOX_8 GPIO_ACTIVE_LOW>;
+ };
+ volume-down-button {
+ label = "VOLUME-DOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&gpio GPIOX_9 GPIO_ACTIVE_LOW>;
+ };
+ dpad-up-button {
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ gpios = <&gpio GPIOX_0 GPIO_ACTIVE_LOW>;
+ };
+ dpad-down-button {
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ gpios = <&gpio GPIOX_1 GPIO_ACTIVE_LOW>;
+ };
+ dpad-left-button {
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ gpios = <&gpio GPIOX_2 GPIO_ACTIVE_LOW>;
+ };
+ dpad-right-button {
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ gpios = <&gpio GPIOX_3 GPIO_ACTIVE_LOW>;
+ };
+ a-button {
+ label = "A";
+ linux,code = <BTN_EAST>;
+ gpios = <&gpio GPIOX_4 GPIO_ACTIVE_LOW>;
+ };
+ b-button {
+ label = "B";
+ linux,code = <BTN_SOUTH>;
+ gpios = <&gpio GPIOX_5 GPIO_ACTIVE_LOW>;
+ };
+ y-button {
+ label = "Y";
+ linux,code = <BTN_WEST>;
+ gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ };
+ x-button {
+ label = "X";
+ linux,code = <BTN_NORTH>;
+ gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ };
+ f1-button {
+ label = "F1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ gpios = <&gpio GPIOX_17 GPIO_ACTIVE_LOW>;
+ };
+ f2-button {
+ label = "F2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+ };
+ f3-button {
+ label = "F3";
+ linux,code = <BTN_TRIGGER_HAPPY3>;
+ gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>;
+ };
+ f4-button {
+ label = "F4";
+ linux,code = <BTN_TRIGGER_HAPPY4>;
+ gpios = <&gpio GPIOX_12 GPIO_ACTIVE_LOW>;
+ };
+ f5-button {
+ label = "F5";
+ linux,code = <BTN_TRIGGER_HAPPY5>;
+ gpios = <&gpio GPIOX_13 GPIO_ACTIVE_LOW>;
+ };
+ f6-button {
+ label = "F6";
+ linux,code = <BTN_TRIGGER_HAPPY6>;
+ gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>;
+ };
+ top-left-button {
+ label = "TOP Left";
+ linux,code = <BTN_TL>;
+ gpios = <&gpio GPIOX_14 GPIO_ACTIVE_LOW>;
+ };
+ top-left2-button {
+ label = "TOP Left 2";
+ linux,code = <BTN_TL2>;
+ gpios = <&gpio GPIOX_19 GPIO_ACTIVE_LOW>;
+ };
+ top-right-button {
+ label = "TOP Right";
+ linux,code = <BTN_TR>;
+ gpios = <&gpio GPIOX_15 GPIO_ACTIVE_LOW>;
+ };
+ top-right2-button {
+ label = "TOP Right 2";
+ linux,code = <BTN_TR2>;
+ gpios = <&gpio GPIOX_18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vdd_sys: regulator-vdd-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_SYS";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "Odroid GO Ultra";
+ audio-widgets = "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+ audio-aux-devs = <&tdmout_b>, <&tdmin_b>, <&speaker_amp>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TDMIN_B IN 1", "TDM_B Capture",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "MICL", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Internal Speakers", "Speaker Amplifier OUTL",
+ "Internal Speakers", "Speaker Amplifier OUTR";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&rk817>;
+ };
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&hp_5v>;
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+/* RK817 only supports 12.5mV steps, round up the values */
+&cpu_opp_table_0 {
+ opp-1000000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <762500>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <837500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1896000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1992000000 {
+ opp-microvolt = <1012500>;
+ };
+};
+
+/* RK818 only supports 12.5mV steps, round up the values */
+&cpub_opp_table_1 {
+ opp-1000000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <825000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <900000>;
+ };
+ opp-1800000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1908000000 {
+ opp-microvolt = <1025000>;
+ };
+};
+
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>;
+ pinctrl-names = "default";
+
+ rk818: pmic@1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_7 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vcc_2v3>;
+ vcc8-supply = <&vcc_2v3>;
+ vcc9-supply = <&vddao_3v3>;
+ boost-supply = <&vdd_sys>;
+ switch-supply = <&vdd_sys>;
+
+ regulators {
+ vddcpu_a: DCDC_REG1 {
+ regulator-name = "vddcpu_a";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <775000>;
+ regulator-max-microvolt = <1025000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <775000>;
+ };
+ };
+
+ vdd_ee: DCDC_REG2 {
+ regulator-name = "vdd_ee";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <875000>;
+ };
+ };
+
+ vddq_1v1: DCDC_REG3 {
+ regulator-name = "vddq_1v1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vddao_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddao_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ hp_5v: DCDC_BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "hp_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vddio_ao1v8: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddio_ao1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddq_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddq_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddio_c: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddio_c";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_sd: SWITCH_REG {
+ regulator-name = "vcc_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio_intc>;
+
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_5 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc5-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_sys>;
+ vcc8-supply = <&vdd_sys>;
+ vcc9-supply = <&rk817_boost>;
+
+ #sound-dai-cells = <0>;
+ clocks = <&codec_clk>;
+ clock-names = "mclk";
+
+ #clock-cells = <1>;
+
+ regulators {
+ vddcpu_b: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <737500>;
+ regulator-max-microvolt = <1012500>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vddcpu_b";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_2v3: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <2400000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_2v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_lcd: LDO_REG8 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "rk817_boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ usb_host: OTG_SWITCH {
+ regulator-name = "usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+ð_phy {
+ status = "disabled";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&periphs_pinctrl {
+ keypad_gpio_pins: keypad-gpio {
+ mux {
+ groups = "GPIOX_0", "GPIOX_1", "GPIOX_2", "GPIOX_3",
+ "GPIOX_4", "GPIOX_5", "GPIOX_6", "GPIOX_7",
+ "GPIOX_8", "GPIOX_9", "GPIOX_10", "GPIOX_11",
+ "GPIOX_12", "GPIOX_13", "GPIOX_14", "GPIOX_15",
+ "GPIOX_16", "GPIOX_17", "GPIOX_18", "GPIOX_19";
+ function = "gpio_periphs";
+ bias-pull-up;
+ output-disable;
+ };
+ };
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_c>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_ao1v8>;
+};
+
+
+&tdmif_b {
+ pinctrl-0 = <&tdm_b_dout0_pins>, <&tdm_b_fs_pins>, <&tdm_b_sclk_pins>, <&tdm_b_din1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ assigned-clocks = <&clkc_audio AUD_CLKID_TDM_SCLK_PAD1>,
+ <&clkc_audio AUD_CLKID_TDM_LRCLK_PAD1>;
+ assigned-clock-parents = <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ assigned-clock-rates = <0>, <0>;
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usb2_phy0 {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ status = "okay";
+ phy-supply = <&usb_host>;
+};
--
b4 0.10.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v2 2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-18 15:50 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-18 15:50 UTC (permalink / raw)
To: Jerome Brunet, Rob Herring, Krzysztof Kozlowski, Kevin Hilman,
Sebastian Reichel, Martin Blumenstingl
Cc: linux-pm, Rob Herring, linux-amlogic, linux-arm-kernel,
devicetree, Neil Armstrong, linux-kernel
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 722 +++++++++++++++++++++
2 files changed, 723 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e213aeebb774..97b42e2100e0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
new file mode 100644
index 000000000000..1e40709610c5
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
@@ -0,0 +1,722 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Neil Armstrong <neil.armstrong@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "hardkernel,odroid-go-ultra", "amlogic,s922x", "amlogic,g12b";
+ model = "Hardkernel ODROID-GO-Ultra";
+
+ aliases {
+ serial0 = &uart_AO;
+ rtc0 = &vrtc;
+ };
+
+ adc-joystick-left {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 2>, <&saradc 3>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_Y>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_X>;
+ abs-range = <700 2900>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ adc-joystick-right {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 0>, <&saradc 1>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis@0 {
+ reg = <0>;
+ linux,code = <ABS_RY>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis@1 {
+ reg = <1>;
+ linux,code = <ABS_RX>;
+ abs-range = <800 3000>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ codec_clk: codec-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ clock-output-names = "codec_clk";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <10>;
+ pinctrl-0 = <&keypad_gpio_pins>;
+ pinctrl-names = "default";
+
+ volume-up-button {
+ label = "VOLUME-UP";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&gpio GPIOX_8 GPIO_ACTIVE_LOW>;
+ };
+ volume-down-button {
+ label = "VOLUME-DOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&gpio GPIOX_9 GPIO_ACTIVE_LOW>;
+ };
+ dpad-up-button {
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ gpios = <&gpio GPIOX_0 GPIO_ACTIVE_LOW>;
+ };
+ dpad-down-button {
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ gpios = <&gpio GPIOX_1 GPIO_ACTIVE_LOW>;
+ };
+ dpad-left-button {
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ gpios = <&gpio GPIOX_2 GPIO_ACTIVE_LOW>;
+ };
+ dpad-right-button {
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ gpios = <&gpio GPIOX_3 GPIO_ACTIVE_LOW>;
+ };
+ a-button {
+ label = "A";
+ linux,code = <BTN_EAST>;
+ gpios = <&gpio GPIOX_4 GPIO_ACTIVE_LOW>;
+ };
+ b-button {
+ label = "B";
+ linux,code = <BTN_SOUTH>;
+ gpios = <&gpio GPIOX_5 GPIO_ACTIVE_LOW>;
+ };
+ y-button {
+ label = "Y";
+ linux,code = <BTN_WEST>;
+ gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ };
+ x-button {
+ label = "X";
+ linux,code = <BTN_NORTH>;
+ gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ };
+ f1-button {
+ label = "F1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ gpios = <&gpio GPIOX_17 GPIO_ACTIVE_LOW>;
+ };
+ f2-button {
+ label = "F2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+ };
+ f3-button {
+ label = "F3";
+ linux,code = <BTN_TRIGGER_HAPPY3>;
+ gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>;
+ };
+ f4-button {
+ label = "F4";
+ linux,code = <BTN_TRIGGER_HAPPY4>;
+ gpios = <&gpio GPIOX_12 GPIO_ACTIVE_LOW>;
+ };
+ f5-button {
+ label = "F5";
+ linux,code = <BTN_TRIGGER_HAPPY5>;
+ gpios = <&gpio GPIOX_13 GPIO_ACTIVE_LOW>;
+ };
+ f6-button {
+ label = "F6";
+ linux,code = <BTN_TRIGGER_HAPPY6>;
+ gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>;
+ };
+ top-left-button {
+ label = "TOP Left";
+ linux,code = <BTN_TL>;
+ gpios = <&gpio GPIOX_14 GPIO_ACTIVE_LOW>;
+ };
+ top-left2-button {
+ label = "TOP Left 2";
+ linux,code = <BTN_TL2>;
+ gpios = <&gpio GPIOX_19 GPIO_ACTIVE_LOW>;
+ };
+ top-right-button {
+ label = "TOP Right";
+ linux,code = <BTN_TR>;
+ gpios = <&gpio GPIOX_15 GPIO_ACTIVE_LOW>;
+ };
+ top-right2-button {
+ label = "TOP Right 2";
+ linux,code = <BTN_TR2>;
+ gpios = <&gpio GPIOX_18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vdd_sys: regulator-vdd-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_SYS";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "Odroid GO Ultra";
+ audio-widgets = "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+ audio-aux-devs = <&tdmout_b>, <&tdmin_b>, <&speaker_amp>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TDMIN_B IN 1", "TDM_B Capture",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "MICL", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Internal Speakers", "Speaker Amplifier OUTL",
+ "Internal Speakers", "Speaker Amplifier OUTR";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&rk817>;
+ };
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&hp_5v>;
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+/* RK817 only supports 12.5mV steps, round up the values */
+&cpu_opp_table_0 {
+ opp-1000000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <762500>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <837500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1896000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1992000000 {
+ opp-microvolt = <1012500>;
+ };
+};
+
+/* RK818 only supports 12.5mV steps, round up the values */
+&cpub_opp_table_1 {
+ opp-1000000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <825000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <900000>;
+ };
+ opp-1800000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1908000000 {
+ opp-microvolt = <1025000>;
+ };
+};
+
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>;
+ pinctrl-names = "default";
+
+ rk818: pmic@1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_7 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vcc_2v3>;
+ vcc8-supply = <&vcc_2v3>;
+ vcc9-supply = <&vddao_3v3>;
+ boost-supply = <&vdd_sys>;
+ switch-supply = <&vdd_sys>;
+
+ regulators {
+ vddcpu_a: DCDC_REG1 {
+ regulator-name = "vddcpu_a";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <775000>;
+ regulator-max-microvolt = <1025000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <775000>;
+ };
+ };
+
+ vdd_ee: DCDC_REG2 {
+ regulator-name = "vdd_ee";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <875000>;
+ };
+ };
+
+ vddq_1v1: DCDC_REG3 {
+ regulator-name = "vddq_1v1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vddao_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddao_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ hp_5v: DCDC_BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "hp_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vddio_ao1v8: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddio_ao1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddq_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddq_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddio_c: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddio_c";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_sd: SWITCH_REG {
+ regulator-name = "vcc_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio_intc>;
+
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_5 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc5-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_sys>;
+ vcc8-supply = <&vdd_sys>;
+ vcc9-supply = <&rk817_boost>;
+
+ #sound-dai-cells = <0>;
+ clocks = <&codec_clk>;
+ clock-names = "mclk";
+
+ #clock-cells = <1>;
+
+ regulators {
+ vddcpu_b: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <737500>;
+ regulator-max-microvolt = <1012500>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vddcpu_b";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_2v3: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <2400000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_2v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_lcd: LDO_REG8 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "rk817_boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ usb_host: OTG_SWITCH {
+ regulator-name = "usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+ð_phy {
+ status = "disabled";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&periphs_pinctrl {
+ keypad_gpio_pins: keypad-gpio {
+ mux {
+ groups = "GPIOX_0", "GPIOX_1", "GPIOX_2", "GPIOX_3",
+ "GPIOX_4", "GPIOX_5", "GPIOX_6", "GPIOX_7",
+ "GPIOX_8", "GPIOX_9", "GPIOX_10", "GPIOX_11",
+ "GPIOX_12", "GPIOX_13", "GPIOX_14", "GPIOX_15",
+ "GPIOX_16", "GPIOX_17", "GPIOX_18", "GPIOX_19";
+ function = "gpio_periphs";
+ bias-pull-up;
+ output-disable;
+ };
+ };
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_c>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_ao1v8>;
+};
+
+
+&tdmif_b {
+ pinctrl-0 = <&tdm_b_dout0_pins>, <&tdm_b_fs_pins>, <&tdm_b_sclk_pins>, <&tdm_b_din1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ assigned-clocks = <&clkc_audio AUD_CLKID_TDM_SCLK_PAD1>,
+ <&clkc_audio AUD_CLKID_TDM_LRCLK_PAD1>;
+ assigned-clock-parents = <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ assigned-clock-rates = <0>, <0>;
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usb2_phy0 {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ status = "okay";
+ phy-supply = <&usb_host>;
+};
--
b4 0.10.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS
2022-11-18 15:50 ` Neil Armstrong
(?)
@ 2022-11-21 10:52 ` Neil Armstrong
-1 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-21 10:52 UTC (permalink / raw)
To: Martin Blumenstingl, Sebastian Reichel, Jerome Brunet,
Neil Armstrong, Kevin Hilman, Rob Herring, Krzysztof Kozlowski
Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree,
linux-pm, Rob Herring
Hi,
On Fri, 18 Nov 2022 16:50:04 +0100, Neil Armstrong wrote:
> This adds initial support for the Hardkernel Odroid Go Ultra.
>
> The Odroid Go Ultra is a portable gaming device with the following
> characteristics:
> - Amlogic S922X SoC
> - RK817 & RK818 PMICs
> - 2GiB LPDDR4
> - On board 16GiB eMMC
> - Micro SD Card slot
> - 5inch 854×480 MIPI-DSI TFT LCD
> - Earphone stereo jack, 0.5Watt 8Ω Mono speaker
> - Li-Polymer 3.7V/4000mAh Battery
> - USB-A 2.0 Host Connector
> - x16 GPIO Input Buttons
> - 2x ADC Analog Joysticks
> - USB-C Port for USB2 Device and Charging
>
> [...]
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.2/arm64-dt)
[1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible
https://git.kernel.org/amlogic/c/66af218f8669a262b1bf89ba80f2acf1a3be429c
[2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
https://git.kernel.org/amlogic/c/62e73f000696cc41cfd237a1ad90b001ad0f76c6
These changes has been applied on the intermediate git tree [1].
The v6.2/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-21 10:52 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-21 10:52 UTC (permalink / raw)
To: Martin Blumenstingl, Sebastian Reichel, Jerome Brunet,
Neil Armstrong, Kevin Hilman, Rob Herring, Krzysztof Kozlowski
Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree,
linux-pm, Rob Herring
Hi,
On Fri, 18 Nov 2022 16:50:04 +0100, Neil Armstrong wrote:
> This adds initial support for the Hardkernel Odroid Go Ultra.
>
> The Odroid Go Ultra is a portable gaming device with the following
> characteristics:
> - Amlogic S922X SoC
> - RK817 & RK818 PMICs
> - 2GiB LPDDR4
> - On board 16GiB eMMC
> - Micro SD Card slot
> - 5inch 854×480 MIPI-DSI TFT LCD
> - Earphone stereo jack, 0.5Watt 8Ω Mono speaker
> - Li-Polymer 3.7V/4000mAh Battery
> - USB-A 2.0 Host Connector
> - x16 GPIO Input Buttons
> - 2x ADC Analog Joysticks
> - USB-C Port for USB2 Device and Charging
>
> [...]
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.2/arm64-dt)
[1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible
https://git.kernel.org/amlogic/c/66af218f8669a262b1bf89ba80f2acf1a3be429c
[2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
https://git.kernel.org/amlogic/c/62e73f000696cc41cfd237a1ad90b001ad0f76c6
These changes has been applied on the intermediate git tree [1].
The v6.2/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS
@ 2022-11-21 10:52 ` Neil Armstrong
0 siblings, 0 replies; 12+ messages in thread
From: Neil Armstrong @ 2022-11-21 10:52 UTC (permalink / raw)
To: Martin Blumenstingl, Sebastian Reichel, Jerome Brunet,
Neil Armstrong, Kevin Hilman, Rob Herring, Krzysztof Kozlowski
Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree,
linux-pm, Rob Herring
Hi,
On Fri, 18 Nov 2022 16:50:04 +0100, Neil Armstrong wrote:
> This adds initial support for the Hardkernel Odroid Go Ultra.
>
> The Odroid Go Ultra is a portable gaming device with the following
> characteristics:
> - Amlogic S922X SoC
> - RK817 & RK818 PMICs
> - 2GiB LPDDR4
> - On board 16GiB eMMC
> - Micro SD Card slot
> - 5inch 854×480 MIPI-DSI TFT LCD
> - Earphone stereo jack, 0.5Watt 8Ω Mono speaker
> - Li-Polymer 3.7V/4000mAh Battery
> - USB-A 2.0 Host Connector
> - x16 GPIO Input Buttons
> - 2x ADC Analog Joysticks
> - USB-C Port for USB2 Device and Charging
>
> [...]
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.2/arm64-dt)
[1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible
https://git.kernel.org/amlogic/c/66af218f8669a262b1bf89ba80f2acf1a3be429c
[2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
https://git.kernel.org/amlogic/c/62e73f000696cc41cfd237a1ad90b001ad0f76c6
These changes has been applied on the intermediate git tree [1].
The v6.2/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2022-11-21 10:53 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-18 15:50 [PATCH v2 0/2] arm64: amlogic: add initial Odroid Go Ultra DTS Neil Armstrong
2022-11-18 15:50 ` Neil Armstrong
2022-11-18 15:50 ` Neil Armstrong
2022-11-18 15:50 ` [PATCH v2 1/2] dt-bindings: amlogic: document Odroid Go Ultra compatible Neil Armstrong
2022-11-18 15:50 ` Neil Armstrong
2022-11-18 15:50 ` Neil Armstrong
2022-11-18 15:50 ` [PATCH v2 2/2] arm64: dts: amlogic: add initial Odroid Go Ultra DTS Neil Armstrong
2022-11-18 15:50 ` Neil Armstrong
2022-11-18 15:50 ` Neil Armstrong
2022-11-21 10:52 ` [PATCH v2 0/2] arm64: " Neil Armstrong
2022-11-21 10:52 ` Neil Armstrong
2022-11-21 10:52 ` Neil Armstrong
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.