[PATCH v4 1/8] arm64: dts: ti: k3-j721s2-main: Add support for USB

[PATCH v4 1/8] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for single instance of USB 3.0 controller in J721S2 SoC.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index d1ec26110376..93b71d079b4f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -26,6 +26,20 @@ l3cache-sram@200000 {
 		};
 	};
 
+	scm_conf: syscon@104000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x00104000 0x00 0x18000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00104000 0x18000>;
+
+		usb_serdes_mux: mux-controller-0 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
@@ -726,6 +740,34 @@ cpts@310d0000 {
 		};
 	};
 
+	usbss0: cdns-usb@4104000 {
+		compatible = "ti,j721e-usb";
+		reg = <0x00 0x04104000 0x00 0x100>;
+		clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
+		clock-names = "ref", "lpm";
+		assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
+		assigned-clock-parents = <&k3_clks 360 17>;
+		power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-coherent;
+
+		usb0: usb@6000000 {
+			compatible = "cdns,usb3";
+			reg = <0x00 0x06000000 0x00 0x10000>,
+			      <0x00 0x06010000 0x00 0x10000>,
+			      <0x00 0x06020000 0x00 0x10000>;
+			reg-names = "otg", "xhci", "dev";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host", "peripheral", "otg";
+			maximum-speed = "super-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.38.GIT

[PATCH v4 1/8] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for single instance of USB 3.0 controller in J721S2 SoC.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index d1ec26110376..93b71d079b4f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -26,6 +26,20 @@ l3cache-sram@200000 {
 		};
 	};
 
+	scm_conf: syscon@104000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x00104000 0x00 0x18000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00104000 0x18000>;
+
+		usb_serdes_mux: mux-controller-0 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
@@ -726,6 +740,34 @@ cpts@310d0000 {
 		};
 	};
 
+	usbss0: cdns-usb@4104000 {
+		compatible = "ti,j721e-usb";
+		reg = <0x00 0x04104000 0x00 0x100>;
+		clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
+		clock-names = "ref", "lpm";
+		assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
+		assigned-clock-parents = <&k3_clks 360 17>;
+		power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-coherent;
+
+		usb0: usb@6000000 {
+			compatible = "cdns,usb3";
+			reg = <0x00 0x06000000 0x00 0x10000>,
+			      <0x00 0x06010000 0x00 0x10000>,
+			      <0x00 0x06020000 0x00 0x10000>;
+			reg-names = "otg", "xhci", "dev";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host", "peripheral", "otg";
+			maximum-speed = "super-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 2/8] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Matt Ranostay]

Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, eDP and USB.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 53 ++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 93b71d079b4f..6f9ccf52363e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -5,6 +5,16 @@
  * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy-ti.h>
+
+/ {
+	serdes_refclk: clock-cmnrefclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+	};
+};
+
 &cbass_main {
 	msmc_ram: sram@70000000 {
 		compatible = "mmio-sram";
@@ -38,6 +48,13 @@ usb_serdes_mux: mux-controller-0 {
 			#mux-control-cells = <1>;
 			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
 		};
+
+		serdes_ln_ctrl: mux-controller-80 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
+					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
+		};
 	};
 
 	gic500: interrupt-controller@1800000 {
@@ -768,6 +785,42 @@ usb0: usb@6000000 {
 		};
 	};
 
+	serdes_wiz0: wiz@5060000 {
+		compatible = "ti,am64-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x5060000 0x0 0x5060000 0x10000>;
+
+		assigned-clocks = <&k3_clks 365 3>;
+		assigned-clock-parents = <&k3_clks 365 7>;
+
+		serdes0: serdes@5060000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05060000 0x00010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz0 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+				 <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>;
+			clock-names = "refclk", "phy_en_refclk";
+			assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz0 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 365 3>,
+						 <&k3_clks 365 3>,
+						 <&k3_clks 365 3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.38.GIT

[PATCH v4 2/8] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Matt Ranostay]

Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, eDP and USB.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 53 ++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 93b71d079b4f..6f9ccf52363e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -5,6 +5,16 @@
  * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy-ti.h>
+
+/ {
+	serdes_refclk: clock-cmnrefclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+	};
+};
+
 &cbass_main {
 	msmc_ram: sram@70000000 {
 		compatible = "mmio-sram";
@@ -38,6 +48,13 @@ usb_serdes_mux: mux-controller-0 {
 			#mux-control-cells = <1>;
 			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
 		};
+
+		serdes_ln_ctrl: mux-controller-80 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
+					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
+		};
 	};
 
 	gic500: interrupt-controller@1800000 {
@@ -768,6 +785,42 @@ usb0: usb@6000000 {
 		};
 	};
 
+	serdes_wiz0: wiz@5060000 {
+		compatible = "ti,am64-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x5060000 0x0 0x5060000 0x10000>;
+
+		assigned-clocks = <&k3_clks 365 3>;
+		assigned-clock-parents = <&k3_clks 365 7>;
+
+		serdes0: serdes@5060000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05060000 0x00010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz0 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+				 <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>;
+			clock-names = "refclk", "phy_en_refclk";
+			assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz0 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 365 3>,
+						 <&k3_clks 365 3>,
+						 <&k3_clks 365 3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 3/8] arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for two instance of OSPI in J721S2 SoC.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 3264b8e8faea..034122be2ed5 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -306,4 +306,44 @@ cpts@3d000 {
 			ti,cpts-periodic-outputs = <2>;
 		};
 	};
+
+	fss: syscon@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ospi0: spi@47040000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47040000 0x00 0x100>,
+			      <0x5 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 109 5>;
+			assigned-clocks = <&k3_clks 109 5>;
+			assigned-clock-parents = <&k3_clks 109 7>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ospi1: spi@47050000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47050000 0x00 0x100>,
+			      <0x7 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 110 5>;
+			power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+	};
 };
-- 
2.38.GIT

[PATCH v4 3/8] arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for two instance of OSPI in J721S2 SoC.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 3264b8e8faea..034122be2ed5 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -306,4 +306,44 @@ cpts@3d000 {
 			ti,cpts-periodic-outputs = <2>;
 		};
 	};
+
+	fss: syscon@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ospi0: spi@47040000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47040000 0x00 0x100>,
+			      <0x5 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 109 5>;
+			assigned-clocks = <&k3_clks 109 5>;
+			assigned-clock-parents = <&k3_clks 109 7>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ospi1: spi@47050000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47050000 0x00 0x100>,
+			      <0x7 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 110 5>;
+			power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+	};
 };
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 4/8] arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Configure first lane to PCIe, the second lane to USB and the last two lanes
to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is
connected to PCIe.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index a7aa6cf08acd..c3a397484c70 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -9,6 +9,9 @@
 
 #include "k3-j721s2-som-p0.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/ti-serdes.h>
 
 / {
 	compatible = "ti,j721s2-evm", "ti,j721s2";
@@ -296,6 +299,25 @@ &cpsw_port1 {
 	phy-handle = <&phy0>;
 };
 
+&serdes_ln_ctrl {
+	idle-states = <J721S2_SERDES0_LANE0_PCIE1_LANE0>, <J721S2_SERDES0_LANE1_USB>,
+		      <J721S2_SERDES0_LANE2_EDP_LANE2>, <J721S2_SERDES0_LANE3_EDP_LANE3>;
+};
+
+&serdes_refclk {
+	clock-frequency = <100000000>;
+};
+
+&serdes0 {
+	serdes0_pcie_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT

[PATCH v4 4/8] arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Configure first lane to PCIe, the second lane to USB and the last two lanes
to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is
connected to PCIe.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index a7aa6cf08acd..c3a397484c70 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -9,6 +9,9 @@
 
 #include "k3-j721s2-som-p0.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/ti-serdes.h>
 
 / {
 	compatible = "ti,j721s2-evm", "ti,j721s2";
@@ -296,6 +299,25 @@ &cpsw_port1 {
 	phy-handle = <&phy0>;
 };
 
+&serdes_ln_ctrl {
+	idle-states = <J721S2_SERDES0_LANE0_PCIE1_LANE0>, <J721S2_SERDES0_LANE1_USB>,
+		      <J721S2_SERDES0_LANE2_EDP_LANE2>, <J721S2_SERDES0_LANE3_EDP_LANE3>;
+};
+
+&serdes_refclk {
+	clock-frequency = <100000000>;
+};
+
+&serdes0 {
+	serdes0_pcie_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 5/8] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

The board uses lane 1 of SERDES for USB. Set the mux
accordingly.

The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c3a397484c70..c787d46f89de 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -318,6 +324,22 @@ serdes0_pcie_link: phy@0 {
 	};
 };
 
+&usb_serdes_mux {
+	idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT

[PATCH v4 5/8] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

The board uses lane 1 of SERDES for USB. Set the mux
accordingly.

The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c3a397484c70..c787d46f89de 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -318,6 +324,22 @@ serdes0_pcie_link: phy@0 {
 	};
 };
 
+&usb_serdes_mux {
+	idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 6/8] arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 34 +++++++++++++++
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     |  4 +-
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 42 +++++++++++++++++++
 3 files changed, 78 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c787d46f89de..0503e690cfaf 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
 			J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
 		>;
 	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+			J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+			J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */
+			J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+			J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+			J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+			J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+			J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+		>;
+	};
 };
 
 &main_gpio2 {
@@ -340,6 +354,26 @@ &usb0 {
 	maximum-speed = "high-speed";
 };
 
+&ospi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 034122be2ed5..95013908048d 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -308,8 +308,8 @@ cpts@3d000 {
 	};
 
 	fss: syscon@47000000 {
-		compatible = "syscon", "simple-mfd";
-		reg = <0x0 0x47000000 0x0 0x100>;
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x47000000 0x00 0x100>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 6930efff8a5a..2ffea00e19d7 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -39,6 +39,28 @@ transceiver0: can-phy0 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
+			J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+			J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+			J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -79,3 +101,23 @@ &main_mcan16 {
 	pinctrl-names = "default";
 	phys = <&transceiver0>;
 };
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
-- 
2.38.GIT

[PATCH v4 6/8] arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 34 +++++++++++++++
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     |  4 +-
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 42 +++++++++++++++++++
 3 files changed, 78 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c787d46f89de..0503e690cfaf 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
 			J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
 		>;
 	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+			J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+			J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */
+			J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+			J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+			J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+			J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+			J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+		>;
+	};
 };
 
 &main_gpio2 {
@@ -340,6 +354,26 @@ &usb0 {
 	maximum-speed = "high-speed";
 };
 
+&ospi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 034122be2ed5..95013908048d 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -308,8 +308,8 @@ cpts@3d000 {
 	};
 
 	fss: syscon@47000000 {
-		compatible = "syscon", "simple-mfd";
-		reg = <0x0 0x47000000 0x0 0x100>;
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x47000000 0x00 0x100>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 6930efff8a5a..2ffea00e19d7 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -39,6 +39,28 @@ transceiver0: can-phy0 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
+			J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+			J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+			J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -79,3 +101,23 @@ &main_mcan16 {
 	pinctrl-names = "default";
 	phys = <&transceiver0>;
 };
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 7/8] arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add PCIe device tree node (both RC and EP) for the single PCIe
instance present in j721s2.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 61 ++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 6f9ccf52363e..0edf6c001289 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -821,6 +821,67 @@ serdes0: serdes@5060000 {
 		};
 	};
 
+	pcie1_rc: pcie@2910000 {
+		compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host";
+		reg = <0x00 0x02910000 0x00 0x1000>,
+		      <0x00 0x02917000 0x00 0x400>,
+		      <0x00 0x0d800000 0x00 0x00800000>,
+		      <0x00 0x18000000 0x00 0x00001000>;
+		reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+		interrupt-names = "link_state";
+		interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+		device_type = "pci";
+		ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+		max-link-speed = <3>;
+		num-lanes = <4>;
+		power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 276 41>;
+		clock-names = "fck";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xff>;
+		vendor-id = <0x104c>;
+		device-id = <0xb013>;
+		msi-map = <0x0 &gic_its 0x0 0x10000>;
+		dma-coherent;
+		ranges = <0x01000000 0x0 0x18001000  0x00 0x18001000  0x0 0x0010000>,
+			 <0x02000000 0x0 0x18011000  0x00 0x18011000  0x0 0x7fef000>;
+		dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */
+				<0 0 0 2 &pcie1_intc 0>, /* INT B */
+				<0 0 0 3 &pcie1_intc 0>, /* INT C */
+				<0 0 0 4 &pcie1_intc 0>; /* INT D */
+
+		pcie1_intc: interrupt-controller {
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	pcie1_ep: pcie-ep@2910000 {
+		compatible = "ti,j7200-pcie-ep", "ti,j721e-pcie-ep";
+		reg = <0x00 0x02910000 0x00 0x1000>,
+		      <0x00 0x02917000 0x00 0x400>,
+		      <0x00 0x0d800000 0x00 0x00800000>,
+		      <0x00 0x18000000 0x00 0x08000000>;
+		reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+		interrupt-names = "link_state";
+		interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+		ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+		max-link-speed = <3>;
+		num-lanes = <4>;
+		power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 276 41>;
+		clock-names = "fck";
+		max-functions = /bits/ 8 <6>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+		dma-coherent;
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.38.GIT

[PATCH v4 7/8] arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add PCIe device tree node (both RC and EP) for the single PCIe
instance present in j721s2.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 61 ++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 6f9ccf52363e..0edf6c001289 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -821,6 +821,67 @@ serdes0: serdes@5060000 {
 		};
 	};
 
+	pcie1_rc: pcie@2910000 {
+		compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host";
+		reg = <0x00 0x02910000 0x00 0x1000>,
+		      <0x00 0x02917000 0x00 0x400>,
+		      <0x00 0x0d800000 0x00 0x00800000>,
+		      <0x00 0x18000000 0x00 0x00001000>;
+		reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+		interrupt-names = "link_state";
+		interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+		device_type = "pci";
+		ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+		max-link-speed = <3>;
+		num-lanes = <4>;
+		power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 276 41>;
+		clock-names = "fck";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xff>;
+		vendor-id = <0x104c>;
+		device-id = <0xb013>;
+		msi-map = <0x0 &gic_its 0x0 0x10000>;
+		dma-coherent;
+		ranges = <0x01000000 0x0 0x18001000  0x00 0x18001000  0x0 0x0010000>,
+			 <0x02000000 0x0 0x18011000  0x00 0x18011000  0x0 0x7fef000>;
+		dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */
+				<0 0 0 2 &pcie1_intc 0>, /* INT B */
+				<0 0 0 3 &pcie1_intc 0>, /* INT C */
+				<0 0 0 4 &pcie1_intc 0>; /* INT D */
+
+		pcie1_intc: interrupt-controller {
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic500>;
+			interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	pcie1_ep: pcie-ep@2910000 {
+		compatible = "ti,j7200-pcie-ep", "ti,j721e-pcie-ep";
+		reg = <0x00 0x02910000 0x00 0x1000>,
+		      <0x00 0x02917000 0x00 0x400>,
+		      <0x00 0x0d800000 0x00 0x00800000>,
+		      <0x00 0x18000000 0x00 0x08000000>;
+		reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+		interrupt-names = "link_state";
+		interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+		ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
+		max-link-speed = <3>;
+		num-lanes = <4>;
+		power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 276 41>;
+		clock-names = "fck";
+		max-functions = /bits/ 8 <6>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+		dma-coherent;
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 8/8] arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

x1 lane PCIe slot in the common processor board is enabled and connected to
J721S2 SOM. Add PCIe DT node in common processor board to reflect the
same.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 .../boot/dts/ti/k3-j721s2-common-proc-board.dts    | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 0503e690cfaf..862611784ab3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -374,6 +374,20 @@ flash@0{
 	};
 };
 
+&pcie1_rc {
+	reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+};
+
+&pcie1_ep {
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+	status = "disabled";
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT

[PATCH v4 8/8] arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

x1 lane PCIe slot in the common processor board is enabled and connected to
J721S2 SOM. Add PCIe DT node in common processor board to reflect the
same.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 .../boot/dts/ti/k3-j721s2-common-proc-board.dts    | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 0503e690cfaf..862611784ab3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -374,6 +374,20 @@ flash@0{
 	};
 };
 
+&pcie1_rc {
+	reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+};
+
+&pcie1_ep {
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+	status = "disabled";
+};
+
 &mcu_mcan0 {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.38.GIT


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 1/8] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Nishanth Menon]

Matt,

On 20:33-20221031, Matt Ranostay wrote:
> From: Aswath Govindraju <a-govindraju@ti.com>
> 
> Add support for single instance of USB 3.0 controller in J721S2 SoC.
> 
> Cc: Vignesh Raghavendra <vigneshr@ti.com>
> Cc: Nishanth Menon <nm@ti.com>
> Acked-by: Matt Ranostay <mranostay@ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

This patch and elsewhere:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/process/submitting-patches.rst#n419
Quote:

"
Any further SoBs (Signed-off-by:'s) following the author's SoB are from
people handling and transporting the patch, but were not involved in its
development. SoB chains should reflect the **real** route a patch took
as it was propagated to the maintainers and ultimately to Linus, with
the first SoB entry signalling primary authorship of a single author.
"

you are part of the hand-off process towards upstream, So, please
sign-off as part of the process.

[...]


-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v4 1/8] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Nishanth Menon]

Matt,

On 20:33-20221031, Matt Ranostay wrote:
> From: Aswath Govindraju <a-govindraju@ti.com>
> 
> Add support for single instance of USB 3.0 controller in J721S2 SoC.
> 
> Cc: Vignesh Raghavendra <vigneshr@ti.com>
> Cc: Nishanth Menon <nm@ti.com>
> Acked-by: Matt Ranostay <mranostay@ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>

This patch and elsewhere:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/process/submitting-patches.rst#n419
Quote:

"
Any further SoBs (Signed-off-by:'s) following the author's SoB are from
people handling and transporting the patch, but were not involved in its
development. SoB chains should reflect the **real** route a patch took
as it was propagated to the maintainers and ultimately to Linus, with
the first SoB entry signalling primary authorship of a single author.
"

you are part of the hand-off process towards upstream, So, please
sign-off as part of the process.

[...]


-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel