[PATCH 1/2] net: stmmac: Power up SERDES after the PHY link

[PATCH 1/2] net: stmmac: Power up SERDES after the PHY link

[Revanth Kumar Uppala]

The Tegra MGBE ethernet controller requires that the SERDES link is
powered-up after the PHY link is up, otherwise the link fails to
become ready following a resume from suspend. Add a variable to indicate
that the SERDES link must be powered-up after the PHY link.

Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 7 +++++--
 include/linux/stmmac.h                            | 1 +
 2 files changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 0a9d13d7976f..3affb7d3a005 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -988,6 +988,9 @@ static void stmmac_mac_link_up(struct phylink_config *config,
 	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
 	u32 old_ctrl, ctrl;
 
+	if (priv->plat->serdes_up_after_phy_linkup && priv->plat->serdes_powerup)
+		priv->plat->serdes_powerup(priv->dev, priv->plat->bsp_priv);
+
 	old_ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
 	ctrl = old_ctrl & ~priv->hw->link.speed_mask;
 
@@ -3801,7 +3804,7 @@ static int __stmmac_open(struct net_device *dev,
 
 	stmmac_reset_queues_param(priv);
 
-	if (priv->plat->serdes_powerup) {
+	if (!priv->plat->serdes_up_after_phy_linkup && priv->plat->serdes_powerup) {
 		ret = priv->plat->serdes_powerup(dev, priv->plat->bsp_priv);
 		if (ret < 0) {
 			netdev_err(priv->dev, "%s: Serdes powerup failed\n",
@@ -7510,7 +7513,7 @@ int stmmac_resume(struct device *dev)
 			stmmac_mdio_reset(priv->mii);
 	}
 
-	if (priv->plat->serdes_powerup) {
+	if (!priv->plat->serdes_up_after_phy_linkup && priv->plat->serdes_powerup) {
 		ret = priv->plat->serdes_powerup(ndev,
 						 priv->plat->bsp_priv);
 
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index fb2e88614f5d..83ca2e8eb6b5 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -271,5 +271,6 @@ struct plat_stmmacenet_data {
 	int msi_tx_base_vec;
 	bool use_phy_wol;
 	bool sph_disable;
+	bool serdes_up_after_phy_linkup;
 };
 #endif
-- 
2.25.1

[PATCH 2/2] net: stmmac: tegra: Add MGBE support

[Revanth Kumar Uppala]

From: Bhadram Varka <vbhadram@nvidia.com>

Add support for the Multi-Gigabit Ethernet (MGBE/XPCS) IP found on
NVIDIA Tegra234 SoCs.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Co-developed-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig   |   6 +
 drivers/net/ethernet/stmicro/stmmac/Makefile  |   1 +
 .../net/ethernet/stmicro/stmmac/dwmac-tegra.c | 387 ++++++++++++++++++
 3 files changed, 394 insertions(+)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-tegra.c

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 31ff35174034..e9f61bdaf7c4 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -235,6 +235,12 @@ config DWMAC_INTEL_PLAT
 	  the stmmac device driver. This driver is used for the Intel Keem Bay
 	  SoC.
 
+config DWMAC_TEGRA
+	tristate "NVIDIA Tegra MGBE support"
+	depends on ARCH_TEGRA || COMPILE_TEST
+	help
+	  Support for the MGBE controller found on Tegra SoCs.
+
 config DWMAC_VISCONTI
 	tristate "Toshiba Visconti DWMAC support"
 	default ARCH_VISCONTI
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index d4e12e9ace4f..057e4bab5c08 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_DWMAC_DWC_QOS_ETH)	+= dwmac-dwc-qos-eth.o
 obj-$(CONFIG_DWMAC_INTEL_PLAT)	+= dwmac-intel-plat.o
 obj-$(CONFIG_DWMAC_GENERIC)	+= dwmac-generic.o
 obj-$(CONFIG_DWMAC_IMX8)	+= dwmac-imx.o
+obj-$(CONFIG_DWMAC_TEGRA)	+= dwmac-tegra.o
 obj-$(CONFIG_DWMAC_VISCONTI)	+= dwmac-visconti.o
 stmmac-platform-objs:= stmmac_platform.o
 dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-tegra.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-tegra.c
new file mode 100644
index 000000000000..9fcaecbae4ad
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-tegra.c
@@ -0,0 +1,387 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/stmmac.h>
+#include <linux/clk.h>
+
+#include "stmmac_platform.h"
+
+static const char *const mgbe_clks[] = {
+	"rx-pcs", "tx", "tx-pcs", "mac-divider", "mac", "mgbe", "ptp-ref", "mac"
+};
+
+struct tegra_mgbe {
+	struct device *dev;
+
+	struct clk_bulk_data *clks;
+
+	struct reset_control *rst_mac;
+	struct reset_control *rst_pcs;
+
+	void __iomem *hv;
+	void __iomem *regs;
+	void __iomem *xpcs;
+
+	struct mii_bus *mii;
+};
+
+#define XPCS_WRAP_UPHY_RX_CONTROL 0x801c
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_SW_OVRD BIT(31)
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_PCS_PHY_RDY BIT(10)
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_CDR_RESET BIT(9)
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_CAL_EN BIT(8)
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_SLEEP (BIT(7) | BIT(6))
+#define XPCS_WRAP_UPHY_RX_CONTROL_AUX_RX_IDDQ BIT(5)
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_IDDQ BIT(4)
+#define XPCS_WRAP_UPHY_RX_CONTROL_RX_DATA_EN BIT(0)
+#define XPCS_WRAP_UPHY_HW_INIT_CTRL 0x8020
+#define XPCS_WRAP_UPHY_HW_INIT_CTRL_TX_EN BIT(0)
+#define XPCS_WRAP_UPHY_HW_INIT_CTRL_RX_EN BIT(2)
+#define XPCS_WRAP_UPHY_STATUS 0x8044
+#define XPCS_WRAP_UPHY_STATUS_TX_P_UP BIT(0)
+#define XPCS_WRAP_IRQ_STATUS 0x8050
+#define XPCS_WRAP_IRQ_STATUS_PCS_LINK_STS BIT(6)
+
+#define XPCS_REG_ADDR_SHIFT 10
+#define XPCS_REG_ADDR_MASK 0x1fff
+#define XPCS_ADDR 0x3fc
+
+#define MGBE_WRAP_COMMON_INTR_ENABLE	0x8704
+#define MAC_SBD_INTR			BIT(2)
+#define MGBE_WRAP_AXI_ASID0_CTRL	0x8400
+#define MGBE_SID			0x6
+
+static int __maybe_unused tegra_mgbe_suspend(struct device *dev)
+{
+	struct tegra_mgbe *mgbe = get_stmmac_bsp_priv(dev);
+	int err;
+
+	err = stmmac_suspend(dev);
+	if (err)
+		return err;
+
+	clk_bulk_disable_unprepare(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+
+	return reset_control_assert(mgbe->rst_mac);
+}
+
+static int __maybe_unused tegra_mgbe_resume(struct device *dev)
+{
+	struct tegra_mgbe *mgbe = get_stmmac_bsp_priv(dev);
+	u32 value;
+	int err;
+
+	err = clk_bulk_prepare_enable(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+	if (err < 0)
+		return err;
+
+	err = reset_control_deassert(mgbe->rst_mac);
+	if (err < 0)
+		return err;
+
+	/* Enable common interrupt at wrapper level */
+	writel(MAC_SBD_INTR, mgbe->regs + MGBE_WRAP_COMMON_INTR_ENABLE);
+
+	/* Program SID */
+	writel(MGBE_SID, mgbe->hv + MGBE_WRAP_AXI_ASID0_CTRL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_STATUS);
+	if ((value & XPCS_WRAP_UPHY_STATUS_TX_P_UP) == 0) {
+		value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_HW_INIT_CTRL);
+		value |= XPCS_WRAP_UPHY_HW_INIT_CTRL_TX_EN;
+		writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_HW_INIT_CTRL);
+	}
+
+	err = readl_poll_timeout(mgbe->xpcs + XPCS_WRAP_UPHY_HW_INIT_CTRL, value,
+				 (value & XPCS_WRAP_UPHY_HW_INIT_CTRL_TX_EN) == 0,
+				 500, 500 * 2000);
+	if (err < 0) {
+		dev_err(mgbe->dev, "timeout waiting for TX lane to become enabled\n");
+		clk_bulk_disable_unprepare(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+		return err;
+	}
+
+	err = stmmac_resume(dev);
+	if (err < 0)
+		clk_bulk_disable_unprepare(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+
+	return err;
+}
+
+static int mgbe_uphy_lane_bringup_serdes_up(struct net_device *ndev, void *mgbe_data)
+{
+	struct tegra_mgbe *mgbe = (struct tegra_mgbe *)mgbe_data;
+	u32 value;
+	int err;
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_SW_OVRD;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value &= ~XPCS_WRAP_UPHY_RX_CONTROL_RX_IDDQ;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value &= ~XPCS_WRAP_UPHY_RX_CONTROL_AUX_RX_IDDQ;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value &= ~XPCS_WRAP_UPHY_RX_CONTROL_RX_SLEEP;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_CAL_EN;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	err = readl_poll_timeout(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL, value,
+				 (value & XPCS_WRAP_UPHY_RX_CONTROL_RX_CAL_EN) == 0,
+				 1000, 1000 * 2000);
+	if (err < 0) {
+		dev_err(mgbe->dev, "timeout waiting for RX calibration to become enabled\n");
+		return err;
+	}
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_DATA_EN;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_CDR_RESET;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value &= ~XPCS_WRAP_UPHY_RX_CONTROL_RX_CDR_RESET;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_PCS_PHY_RDY;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	err = readl_poll_timeout(mgbe->xpcs + XPCS_WRAP_IRQ_STATUS, value,
+				 value & XPCS_WRAP_IRQ_STATUS_PCS_LINK_STS,
+				 500, 500 * 2000);
+	if (err < 0) {
+		dev_err(mgbe->dev, "timeout waiting for link to become ready\n");
+		return err;
+	}
+
+	/* clear status */
+	writel(value, mgbe->xpcs + XPCS_WRAP_IRQ_STATUS);
+
+	return 0;
+}
+
+static void mgbe_uphy_lane_bringup_serdes_down(struct net_device *ndev, void *mgbe_data)
+{
+	struct tegra_mgbe *mgbe = (struct tegra_mgbe *)mgbe_data;
+	u32 value;
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_SW_OVRD;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value &= ~XPCS_WRAP_UPHY_RX_CONTROL_RX_DATA_EN;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_SLEEP;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_AUX_RX_IDDQ;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+	value |= XPCS_WRAP_UPHY_RX_CONTROL_RX_IDDQ;
+	writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_RX_CONTROL);
+}
+
+static int tegra_mgbe_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat;
+	struct stmmac_resources res;
+	struct tegra_mgbe *mgbe;
+	int irq, err, i;
+	u32 value;
+
+	mgbe = devm_kzalloc(&pdev->dev, sizeof(*mgbe), GFP_KERNEL);
+	if (!mgbe)
+		return -ENOMEM;
+
+	mgbe->dev = &pdev->dev;
+
+	memset(&res, 0, sizeof(res));
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	mgbe->hv = devm_platform_ioremap_resource_byname(pdev, "hypervisor");
+	if (IS_ERR(mgbe->hv))
+		return PTR_ERR(mgbe->hv);
+
+	mgbe->regs = devm_platform_ioremap_resource_byname(pdev, "mac");
+	if (IS_ERR(mgbe->regs))
+		return PTR_ERR(mgbe->regs);
+
+	mgbe->xpcs = devm_platform_ioremap_resource_byname(pdev, "xpcs");
+	if (IS_ERR(mgbe->xpcs))
+		return PTR_ERR(mgbe->xpcs);
+
+	res.addr = mgbe->regs;
+	res.irq = irq;
+
+	mgbe->clks = devm_kzalloc(&pdev->dev, sizeof(*mgbe->clks), GFP_KERNEL);
+	if (!mgbe->clks)
+		return -ENOMEM;
+
+	for (i = 0; i <  ARRAY_SIZE(mgbe_clks); i++)
+		mgbe->clks[i].id = mgbe_clks[i];
+
+	err = devm_clk_bulk_get(mgbe->dev, ARRAY_SIZE(mgbe_clks), mgbe->clks);
+	if (err < 0)
+		return err;
+
+	err = clk_bulk_prepare_enable(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+	if (err < 0)
+		return err;
+
+	/* Perform MAC reset */
+	mgbe->rst_mac = devm_reset_control_get(&pdev->dev, "mac");
+	if (IS_ERR(mgbe->rst_mac)) {
+		err = PTR_ERR(mgbe->rst_mac);
+		goto disable_clks;
+	}
+
+	err = reset_control_assert(mgbe->rst_mac);
+	if (err < 0)
+		goto disable_clks;
+
+	usleep_range(2000, 4000);
+
+	err = reset_control_deassert(mgbe->rst_mac);
+	if (err < 0)
+		goto disable_clks;
+
+	/* Perform PCS reset */
+	mgbe->rst_pcs = devm_reset_control_get(&pdev->dev, "pcs");
+	if (IS_ERR(mgbe->rst_pcs)) {
+		err = PTR_ERR(mgbe->rst_pcs);
+		goto disable_clks;
+	}
+
+	err = reset_control_assert(mgbe->rst_pcs);
+	if (err < 0)
+		goto disable_clks;
+
+	usleep_range(2000, 4000);
+
+	err = reset_control_deassert(mgbe->rst_pcs);
+	if (err < 0)
+		goto disable_clks;
+
+	plat = stmmac_probe_config_dt(pdev, res.mac);
+	if (IS_ERR(plat)) {
+		err = PTR_ERR(plat);
+		goto disable_clks;
+	}
+
+	plat->has_xgmac = 1;
+	plat->tso_en = 1;
+	plat->pmt = 1;
+	plat->bsp_priv = mgbe;
+
+	if (!plat->mdio_node)
+		plat->mdio_node = of_get_child_by_name(pdev->dev.of_node, "mdio");
+
+	if (!plat->mdio_bus_data) {
+		plat->mdio_bus_data = devm_kzalloc(&pdev->dev, sizeof(*plat->mdio_bus_data),
+						   GFP_KERNEL);
+		if (!plat->mdio_bus_data) {
+			err = -ENOMEM;
+			goto remove;
+		}
+	}
+
+	plat->mdio_bus_data->needs_reset = true;
+
+	value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_STATUS);
+	if ((value & XPCS_WRAP_UPHY_STATUS_TX_P_UP) == 0) {
+		value = readl(mgbe->xpcs + XPCS_WRAP_UPHY_HW_INIT_CTRL);
+		value |= XPCS_WRAP_UPHY_HW_INIT_CTRL_TX_EN;
+		writel(value, mgbe->xpcs + XPCS_WRAP_UPHY_HW_INIT_CTRL);
+	}
+
+	err = readl_poll_timeout(mgbe->xpcs + XPCS_WRAP_UPHY_HW_INIT_CTRL, value,
+				 (value & XPCS_WRAP_UPHY_HW_INIT_CTRL_TX_EN) == 0,
+				 500, 500 * 2000);
+	if (err < 0) {
+		dev_err(mgbe->dev, "timeout waiting for TX lane to become enabled\n");
+		goto remove;
+	}
+
+	plat->serdes_powerup = mgbe_uphy_lane_bringup_serdes_up;
+	plat->serdes_powerdown = mgbe_uphy_lane_bringup_serdes_down;
+
+	/* Tx FIFO Size - 128KB */
+	plat->tx_fifo_size = 131072;
+	/* Rx FIFO Size - 192KB */
+	plat->rx_fifo_size = 196608;
+
+	/* Enable common interrupt at wrapper level */
+	writel(MAC_SBD_INTR, mgbe->regs + MGBE_WRAP_COMMON_INTR_ENABLE);
+
+	/* Program SID */
+	writel(MGBE_SID, mgbe->hv + MGBE_WRAP_AXI_ASID0_CTRL);
+
+	plat->serdes_up_after_phy_linkup = 1;
+
+	err = stmmac_dvr_probe(&pdev->dev, plat, &res);
+	if (err < 0)
+		goto remove;
+
+	return 0;
+
+disable_clks:
+	clk_bulk_disable_unprepare(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+remove:
+	stmmac_remove_config_dt(pdev, plat);
+	return err;
+}
+
+static int tegra_mgbe_remove(struct platform_device *pdev)
+{
+	struct tegra_mgbe *mgbe = get_stmmac_bsp_priv(&pdev->dev);
+
+	clk_bulk_disable_unprepare(ARRAY_SIZE(mgbe_clks), mgbe->clks);
+
+	stmmac_pltfr_remove(pdev);
+
+	return 0;
+}
+
+static const struct of_device_id tegra_mgbe_match[] = {
+	{ .compatible = "nvidia,tegra234-mgbe", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, tegra_mgbe_match);
+
+static SIMPLE_DEV_PM_OPS(tegra_mgbe_pm_ops, tegra_mgbe_suspend, tegra_mgbe_resume);
+
+static struct platform_driver tegra_mgbe_driver = {
+	.probe = tegra_mgbe_probe,
+	.remove = tegra_mgbe_remove,
+	.driver = {
+		.name = "tegra-mgbe",
+		.pm		= &tegra_mgbe_pm_ops,
+		.of_match_table = tegra_mgbe_match,
+	},
+};
+module_platform_driver(tegra_mgbe_driver);
+
+MODULE_AUTHOR("Thierry Reding <treding@nvidia.com>");
+MODULE_DESCRIPTION("NVIDIA Tegra MGBE driver");
+MODULE_LICENSE("GPL");
-- 
2.25.1

Re: [PATCH 2/2] net: stmmac: tegra: Add MGBE support

[Jon Hunter]

On 18/11/2022 07:57, Revanth Kumar Uppala wrote:
> From: Bhadram Varka <vbhadram@nvidia.com>
> 
> Add support for the Multi-Gigabit Ethernet (MGBE/XPCS) IP found on
> NVIDIA Tegra234 SoCs.
> 
> Signed-off-by: Thierry Reding <treding@nvidia.com>
> Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
> Co-developed-by: Revanth Kumar Uppala <ruppala@nvidia.com>
> Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
> ---

This should have been marked as 'V5'. If we need to resend please let us 
know. We are also missing what has been changed since the last version. 
I know that in this version the following changes were made:

1. Reduce time spent polling for the RX link to be ready
2. Propagate the errors when bringing up the link fails.
3. Added suspend/resume support
4. Ensure clocks are disabled again on probe/resume failure

Otherwise ...

Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>

Thanks
Jon

-- 
nvpublic

Re: [PATCH 2/2] net: stmmac: tegra: Add MGBE support

[Paolo Abeni]

Hello,

On Fri, 2022-11-18 at 13:27 +0530, Revanth Kumar Uppala wrote:
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> index 31ff35174034..e9f61bdaf7c4 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> @@ -235,6 +235,12 @@ config DWMAC_INTEL_PLAT
>  	  the stmmac device driver. This driver is used for the Intel Keem Bay
>  	  SoC.
>  
> +config DWMAC_TEGRA
> +	tristate "NVIDIA Tegra MGBE support"
> +	depends on ARCH_TEGRA || COMPILE_TEST
> +	help
> +	  Support for the MGBE controller found on Tegra SoCs.

Minor nit: checkpatch is complaining for a more descriptive config
option text.

> +static int tegra_mgbe_probe(struct platform_device *pdev)
> +{
> +	struct plat_stmmacenet_data *plat;
> +	struct stmmac_resources res;
> +	struct tegra_mgbe *mgbe;
> +	int irq, err, i;
> +	u32 value;
> +
> +	mgbe = devm_kzalloc(&pdev->dev, sizeof(*mgbe), GFP_KERNEL);
> +	if (!mgbe)
> +		return -ENOMEM;
> +
> +	mgbe->dev = &pdev->dev;
> +
> +	memset(&res, 0, sizeof(res));
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	mgbe->hv = devm_platform_ioremap_resource_byname(pdev, "hypervisor");
> +	if (IS_ERR(mgbe->hv))
> +		return PTR_ERR(mgbe->hv);
> +
> +	mgbe->regs = devm_platform_ioremap_resource_byname(pdev, "mac");
> +	if (IS_ERR(mgbe->regs))
> +		return PTR_ERR(mgbe->regs);
> +
> +	mgbe->xpcs = devm_platform_ioremap_resource_byname(pdev, "xpcs");
> +	if (IS_ERR(mgbe->xpcs))
> +		return PTR_ERR(mgbe->xpcs);
> +
> +	res.addr = mgbe->regs;
> +	res.irq = irq;
> +
> +	mgbe->clks = devm_kzalloc(&pdev->dev, sizeof(*mgbe->clks), GFP_KERNEL);
> +	if (!mgbe->clks)
> +		return -ENOMEM;
> +
> +	for (i = 0; i <  ARRAY_SIZE(mgbe_clks); i++)
> +		mgbe->clks[i].id = mgbe_clks[i];
> +
> +	err = devm_clk_bulk_get(mgbe->dev, ARRAY_SIZE(mgbe_clks), mgbe->clks);
> +	if (err < 0)
> +		return err;
> +
> +	err = clk_bulk_prepare_enable(ARRAY_SIZE(mgbe_clks), mgbe->clks);
> +	if (err < 0)
> +		return err;
> +
> +	/* Perform MAC reset */
> +	mgbe->rst_mac = devm_reset_control_get(&pdev->dev, "mac");
> +	if (IS_ERR(mgbe->rst_mac)) {
> +		err = PTR_ERR(mgbe->rst_mac);

This triggers a clang warning:

../drivers/net/ethernet/stmicro/stmmac/dwmac-tegra.c:283:6: warning: variable 'plat' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]

I guess you have to init plat to NULL and explcitly check for NULL
values under the 'remove' label.

Cheers,

Paolo