[PATCH v4 0/9] Add MediaTek MT7986 SPI NAND and ECC support

[PATCH v4 0/9] Add MediaTek MT7986 SPI NAND and ECC support

[Xiangsheng Hou]

This patch series add MediaTek MT7986 SPI NAND and ECC controller
support, split ECC engine with rawnand controller in bindings and
change to YAML schema.

Changes since V3:
 - Correct mediatek,mtk-nfc.yaml dt-bindings.

Changes since V2:
 - Change ECC err_mask value with GENMASK macro.
 - Change snfi mediatek,rx-latch-latency to mediatek,rx-latch-latency-ns.
 - Add a separate patch for DTS change.
 - Move common description to top-level pattern properties.
 - Drop redundant parts in dt-bindings.

Changes since V1:
 - Use existing sample delay property.
 - Add restricting for optional nfi_hclk.
 - Improve and perfect dt-bindings documentation.
 - Change existing node name to match NAND controller DT bingings.
 - Fix issues reported by dt_binding_check.
 - Fix issues reported by dtbs_check.

Xiangsheng Hou (9):
  spi: mtk-snfi: Change default page format to setup default setting
  spi: mtk-snfi: Add optional nfi_hclk which is needed for MT7986
  mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
  dt-bindings: spi: mtk-snfi: Add compatible for MT7986
  spi: mtk-snfi: Add snfi sample delay and read latency adjustment
  dt-bindings: spi: mtk-snfi: Add read latch latency property
  dt-bindings: mtd: Split ECC engine with rawnand controller
  arm/arm64: dts: mediatek: Fix existing NAND controller node name
  dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986

 .../bindings/mtd/mediatek,mtk-nfc.yaml        | 155 +++++++++++++++
 .../mtd/mediatek,nand-ecc-engine.yaml         |  63 +++++++
 .../devicetree/bindings/mtd/mtk-nand.txt      | 176 ------------------
 .../bindings/spi/mediatek,spi-mtk-snfi.yaml   |  54 +++++-
 arch/arm/boot/dts/mt2701.dtsi                 |   2 +-
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi     |   2 +-
 arch/arm64/boot/dts/mediatek/mt7622.dtsi      |   2 +-
 drivers/mtd/nand/ecc-mtk.c                    |  28 ++-
 drivers/spi/spi-mtk-snfi.c                    |  41 +++-
 9 files changed, 330 insertions(+), 193 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
 delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

-- 
2.25.1

[PATCH v4 0/9] Add MediaTek MT7986 SPI NAND and ECC support

[Xiangsheng Hou]

This patch series add MediaTek MT7986 SPI NAND and ECC controller
support, split ECC engine with rawnand controller in bindings and
change to YAML schema.

Changes since V3:
 - Correct mediatek,mtk-nfc.yaml dt-bindings.

Changes since V2:
 - Change ECC err_mask value with GENMASK macro.
 - Change snfi mediatek,rx-latch-latency to mediatek,rx-latch-latency-ns.
 - Add a separate patch for DTS change.
 - Move common description to top-level pattern properties.
 - Drop redundant parts in dt-bindings.

Changes since V1:
 - Use existing sample delay property.
 - Add restricting for optional nfi_hclk.
 - Improve and perfect dt-bindings documentation.
 - Change existing node name to match NAND controller DT bingings.
 - Fix issues reported by dt_binding_check.
 - Fix issues reported by dtbs_check.

Xiangsheng Hou (9):
  spi: mtk-snfi: Change default page format to setup default setting
  spi: mtk-snfi: Add optional nfi_hclk which is needed for MT7986
  mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
  dt-bindings: spi: mtk-snfi: Add compatible for MT7986
  spi: mtk-snfi: Add snfi sample delay and read latency adjustment
  dt-bindings: spi: mtk-snfi: Add read latch latency property
  dt-bindings: mtd: Split ECC engine with rawnand controller
  arm/arm64: dts: mediatek: Fix existing NAND controller node name
  dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986

 .../bindings/mtd/mediatek,mtk-nfc.yaml        | 155 +++++++++++++++
 .../mtd/mediatek,nand-ecc-engine.yaml         |  63 +++++++
 .../devicetree/bindings/mtd/mtk-nand.txt      | 176 ------------------
 .../bindings/spi/mediatek,spi-mtk-snfi.yaml   |  54 +++++-
 arch/arm/boot/dts/mt2701.dtsi                 |   2 +-
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi     |   2 +-
 arch/arm64/boot/dts/mediatek/mt7622.dtsi      |   2 +-
 drivers/mtd/nand/ecc-mtk.c                    |  28 ++-
 drivers/spi/spi-mtk-snfi.c                    |  41 +++-
 9 files changed, 330 insertions(+), 193 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
 delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 0/9] Add MediaTek MT7986 SPI NAND and ECC support

[Xiangsheng Hou]

This patch series add MediaTek MT7986 SPI NAND and ECC controller
support, split ECC engine with rawnand controller in bindings and
change to YAML schema.

Changes since V3:
 - Correct mediatek,mtk-nfc.yaml dt-bindings.

Changes since V2:
 - Change ECC err_mask value with GENMASK macro.
 - Change snfi mediatek,rx-latch-latency to mediatek,rx-latch-latency-ns.
 - Add a separate patch for DTS change.
 - Move common description to top-level pattern properties.
 - Drop redundant parts in dt-bindings.

Changes since V1:
 - Use existing sample delay property.
 - Add restricting for optional nfi_hclk.
 - Improve and perfect dt-bindings documentation.
 - Change existing node name to match NAND controller DT bingings.
 - Fix issues reported by dt_binding_check.
 - Fix issues reported by dtbs_check.

Xiangsheng Hou (9):
  spi: mtk-snfi: Change default page format to setup default setting
  spi: mtk-snfi: Add optional nfi_hclk which is needed for MT7986
  mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
  dt-bindings: spi: mtk-snfi: Add compatible for MT7986
  spi: mtk-snfi: Add snfi sample delay and read latency adjustment
  dt-bindings: spi: mtk-snfi: Add read latch latency property
  dt-bindings: mtd: Split ECC engine with rawnand controller
  arm/arm64: dts: mediatek: Fix existing NAND controller node name
  dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986

 .../bindings/mtd/mediatek,mtk-nfc.yaml        | 155 +++++++++++++++
 .../mtd/mediatek,nand-ecc-engine.yaml         |  63 +++++++
 .../devicetree/bindings/mtd/mtk-nand.txt      | 176 ------------------
 .../bindings/spi/mediatek,spi-mtk-snfi.yaml   |  54 +++++-
 arch/arm/boot/dts/mt2701.dtsi                 |   2 +-
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi     |   2 +-
 arch/arm64/boot/dts/mediatek/mt7622.dtsi      |   2 +-
 drivers/mtd/nand/ecc-mtk.c                    |  28 ++-
 drivers/spi/spi-mtk-snfi.c                    |  41 +++-
 9 files changed, 330 insertions(+), 193 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
 delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 1/9] spi: mtk-snfi: Change default page format to setup default setting

[Xiangsheng Hou]

Change default page format to setup default setting since the sector
size 1024 on MT7986 will lead to probe fail.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 drivers/spi/spi-mtk-snfi.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index fa8412ba20e2..719fc6f53ab1 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -1430,8 +1430,7 @@ static int mtk_snand_probe(struct platform_device *pdev)
 
 	// setup an initial page format for ops matching page_cache_op template
 	// before ECC is called.
-	ret = mtk_snand_setup_pagefmt(ms, ms->caps->sector_size,
-				      ms->caps->spare_sizes[0]);
+	ret = mtk_snand_setup_pagefmt(ms, SZ_2K, SZ_64);
 	if (ret) {
 		dev_err(ms->dev, "failed to set initial page format\n");
 		goto disable_clk;
-- 
2.25.1

[PATCH v4 1/9] spi: mtk-snfi: Change default page format to setup default setting

[Xiangsheng Hou]

Change default page format to setup default setting since the sector
size 1024 on MT7986 will lead to probe fail.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 drivers/spi/spi-mtk-snfi.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index fa8412ba20e2..719fc6f53ab1 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -1430,8 +1430,7 @@ static int mtk_snand_probe(struct platform_device *pdev)
 
 	// setup an initial page format for ops matching page_cache_op template
 	// before ECC is called.
-	ret = mtk_snand_setup_pagefmt(ms, ms->caps->sector_size,
-				      ms->caps->spare_sizes[0]);
+	ret = mtk_snand_setup_pagefmt(ms, SZ_2K, SZ_64);
 	if (ret) {
 		dev_err(ms->dev, "failed to set initial page format\n");
 		goto disable_clk;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 1/9] spi: mtk-snfi: Change default page format to setup default setting

[Xiangsheng Hou]

Change default page format to setup default setting since the sector
size 1024 on MT7986 will lead to probe fail.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 drivers/spi/spi-mtk-snfi.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index fa8412ba20e2..719fc6f53ab1 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -1430,8 +1430,7 @@ static int mtk_snand_probe(struct platform_device *pdev)
 
 	// setup an initial page format for ops matching page_cache_op template
 	// before ECC is called.
-	ret = mtk_snand_setup_pagefmt(ms, ms->caps->sector_size,
-				      ms->caps->spare_sizes[0]);
+	ret = mtk_snand_setup_pagefmt(ms, SZ_2K, SZ_64);
 	if (ret) {
 		dev_err(ms->dev, "failed to set initial page format\n");
 		goto disable_clk;
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] spi: mtk-snfi: Change default page format to setup default setting

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 445 bytes --]

On Fri, Dec 09, 2022 at 02:43:09PM +0800, Xiangsheng Hou wrote:
> Change default page format to setup default setting since the sector
> size 1024 on MT7986 will lead to probe fail.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---
>  drivers/spi/spi-mtk-snfi.c | 3 +--
>  1 file changed, 1 insertion(+), 2 deletions(-)

Angelo, you've not reviewed this one - is there some problem with it or
was it just missed?

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 144 bytes --]

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 1/9] spi: mtk-snfi: Change default page format to setup default setting

[Mark Brown]

[-- Attachment #1.1: Type: text/plain, Size: 445 bytes --]

On Fri, Dec 09, 2022 at 02:43:09PM +0800, Xiangsheng Hou wrote:
> Change default page format to setup default setting since the sector
> size 1024 on MT7986 will lead to probe fail.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---
>  drivers/spi/spi-mtk-snfi.c | 3 +--
>  1 file changed, 1 insertion(+), 2 deletions(-)

Angelo, you've not reviewed this one - is there some problem with it or
was it just missed?

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 1/9] spi: mtk-snfi: Change default page format to setup default setting

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 445 bytes --]

On Fri, Dec 09, 2022 at 02:43:09PM +0800, Xiangsheng Hou wrote:
> Change default page format to setup default setting since the sector
> size 1024 on MT7986 will lead to probe fail.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---
>  drivers/spi/spi-mtk-snfi.c | 3 +--
>  1 file changed, 1 insertion(+), 2 deletions(-)

Angelo, you've not reviewed this one - is there some problem with it or
was it just missed?

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[PATCH v4 2/9] spi: mtk-snfi: Add optional nfi_hclk which is needed for MT7986

[Xiangsheng Hou]

Add optional nfi_hclk which is needed for MT7986.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/spi/spi-mtk-snfi.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index 719fc6f53ab1..85644308df23 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -297,6 +297,7 @@ struct mtk_snand {
 	struct device *dev;
 	struct clk *nfi_clk;
 	struct clk *pad_clk;
+	struct clk *nfi_hclk;
 	void __iomem *nfi_base;
 	int irq;
 	struct completion op_done;
@@ -1339,7 +1340,16 @@ static int mtk_snand_enable_clk(struct mtk_snand *ms)
 		dev_err(ms->dev, "unable to enable pad clk\n");
 		goto err1;
 	}
+	ret = clk_prepare_enable(ms->nfi_hclk);
+	if (ret) {
+		dev_err(ms->dev, "unable to enable nfi hclk\n");
+		goto err2;
+	}
+
 	return 0;
+
+err2:
+	clk_disable_unprepare(ms->pad_clk);
 err1:
 	clk_disable_unprepare(ms->nfi_clk);
 	return ret;
@@ -1347,6 +1357,7 @@ static int mtk_snand_enable_clk(struct mtk_snand *ms)
 
 static void mtk_snand_disable_clk(struct mtk_snand *ms)
 {
+	clk_disable_unprepare(ms->nfi_hclk);
 	clk_disable_unprepare(ms->pad_clk);
 	clk_disable_unprepare(ms->nfi_clk);
 }
@@ -1401,6 +1412,13 @@ static int mtk_snand_probe(struct platform_device *pdev)
 		goto release_ecc;
 	}
 
+	ms->nfi_hclk = devm_clk_get_optional(&pdev->dev, "nfi_hclk");
+	if (IS_ERR(ms->nfi_hclk)) {
+		ret = PTR_ERR(ms->nfi_hclk);
+		dev_err(&pdev->dev, "unable to get nfi_hclk, err = %d\n", ret);
+		goto release_ecc;
+	}
+
 	ret = mtk_snand_enable_clk(ms);
 	if (ret)
 		goto release_ecc;
-- 
2.25.1

[PATCH v4 2/9] spi: mtk-snfi: Add optional nfi_hclk which is needed for MT7986

[Xiangsheng Hou]

Add optional nfi_hclk which is needed for MT7986.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/spi/spi-mtk-snfi.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index 719fc6f53ab1..85644308df23 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -297,6 +297,7 @@ struct mtk_snand {
 	struct device *dev;
 	struct clk *nfi_clk;
 	struct clk *pad_clk;
+	struct clk *nfi_hclk;
 	void __iomem *nfi_base;
 	int irq;
 	struct completion op_done;
@@ -1339,7 +1340,16 @@ static int mtk_snand_enable_clk(struct mtk_snand *ms)
 		dev_err(ms->dev, "unable to enable pad clk\n");
 		goto err1;
 	}
+	ret = clk_prepare_enable(ms->nfi_hclk);
+	if (ret) {
+		dev_err(ms->dev, "unable to enable nfi hclk\n");
+		goto err2;
+	}
+
 	return 0;
+
+err2:
+	clk_disable_unprepare(ms->pad_clk);
 err1:
 	clk_disable_unprepare(ms->nfi_clk);
 	return ret;
@@ -1347,6 +1357,7 @@ static int mtk_snand_enable_clk(struct mtk_snand *ms)
 
 static void mtk_snand_disable_clk(struct mtk_snand *ms)
 {
+	clk_disable_unprepare(ms->nfi_hclk);
 	clk_disable_unprepare(ms->pad_clk);
 	clk_disable_unprepare(ms->nfi_clk);
 }
@@ -1401,6 +1412,13 @@ static int mtk_snand_probe(struct platform_device *pdev)
 		goto release_ecc;
 	}
 
+	ms->nfi_hclk = devm_clk_get_optional(&pdev->dev, "nfi_hclk");
+	if (IS_ERR(ms->nfi_hclk)) {
+		ret = PTR_ERR(ms->nfi_hclk);
+		dev_err(&pdev->dev, "unable to get nfi_hclk, err = %d\n", ret);
+		goto release_ecc;
+	}
+
 	ret = mtk_snand_enable_clk(ms);
 	if (ret)
 		goto release_ecc;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 2/9] spi: mtk-snfi: Add optional nfi_hclk which is needed for MT7986

[Xiangsheng Hou]

Add optional nfi_hclk which is needed for MT7986.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/spi/spi-mtk-snfi.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index 719fc6f53ab1..85644308df23 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -297,6 +297,7 @@ struct mtk_snand {
 	struct device *dev;
 	struct clk *nfi_clk;
 	struct clk *pad_clk;
+	struct clk *nfi_hclk;
 	void __iomem *nfi_base;
 	int irq;
 	struct completion op_done;
@@ -1339,7 +1340,16 @@ static int mtk_snand_enable_clk(struct mtk_snand *ms)
 		dev_err(ms->dev, "unable to enable pad clk\n");
 		goto err1;
 	}
+	ret = clk_prepare_enable(ms->nfi_hclk);
+	if (ret) {
+		dev_err(ms->dev, "unable to enable nfi hclk\n");
+		goto err2;
+	}
+
 	return 0;
+
+err2:
+	clk_disable_unprepare(ms->pad_clk);
 err1:
 	clk_disable_unprepare(ms->nfi_clk);
 	return ret;
@@ -1347,6 +1357,7 @@ static int mtk_snand_enable_clk(struct mtk_snand *ms)
 
 static void mtk_snand_disable_clk(struct mtk_snand *ms)
 {
+	clk_disable_unprepare(ms->nfi_hclk);
 	clk_disable_unprepare(ms->pad_clk);
 	clk_disable_unprepare(ms->nfi_clk);
 }
@@ -1401,6 +1412,13 @@ static int mtk_snand_probe(struct platform_device *pdev)
 		goto release_ecc;
 	}
 
+	ms->nfi_hclk = devm_clk_get_optional(&pdev->dev, "nfi_hclk");
+	if (IS_ERR(ms->nfi_hclk)) {
+		ret = PTR_ERR(ms->nfi_hclk);
+		dev_err(&pdev->dev, "unable to get nfi_hclk, err = %d\n", ret);
+		goto release_ecc;
+	}
+
 	ret = mtk_snand_enable_clk(ms);
 	if (ret)
 		goto release_ecc;
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 3/9] mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC

[Xiangsheng Hou]

Add ECC support fot MT7986 IC, and change err_mask value with
GENMASK macro.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 drivers/mtd/nand/ecc-mtk.c | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/ecc-mtk.c b/drivers/mtd/nand/ecc-mtk.c
index 9f9b201fe706..c75bb8b80cc1 100644
--- a/drivers/mtd/nand/ecc-mtk.c
+++ b/drivers/mtd/nand/ecc-mtk.c
@@ -40,6 +40,10 @@
 #define ECC_IDLE_REG(op)	((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE)
 #define ECC_CTL_REG(op)		((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON)
 
+#define ECC_ERRMASK_MT7622	GENMASK(4, 0)
+#define ECC_ERRMASK_MT2701	GENMASK(5, 0)
+#define ECC_ERRMASK_MT2712	GENMASK(6, 0)
+
 struct mtk_ecc_caps {
 	u32 err_mask;
 	u32 err_shift;
@@ -79,6 +83,10 @@ static const u8 ecc_strength_mt7622[] = {
 	4, 6, 8, 10, 12
 };
 
+static const u8 ecc_strength_mt7986[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
+};
+
 enum mtk_ecc_regs {
 	ECC_ENCPAR00,
 	ECC_ENCIRQ_EN,
@@ -451,7 +459,7 @@ unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc)
 EXPORT_SYMBOL(mtk_ecc_get_parity_bits);
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
-	.err_mask = 0x3f,
+	.err_mask = ECC_ERRMASK_MT2701,
 	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2701,
 	.ecc_regs = mt2701_ecc_regs,
@@ -462,7 +470,7 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
-	.err_mask = 0x7f,
+	.err_mask = ECC_ERRMASK_MT2712,
 	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2712,
 	.ecc_regs = mt2712_ecc_regs,
@@ -473,7 +481,7 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
-	.err_mask = 0x1f,
+	.err_mask = ECC_ERRMASK_MT7622,
 	.err_shift = 5,
 	.ecc_strength = ecc_strength_mt7622,
 	.ecc_regs = mt7622_ecc_regs,
@@ -483,6 +491,17 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
 	.pg_irq_sel = 0,
 };
 
+static const struct mtk_ecc_caps mtk_ecc_caps_mt7986 = {
+	.err_mask = ECC_ERRMASK_MT7622,
+	.err_shift = 8,
+	.ecc_strength = ecc_strength_mt7986,
+	.ecc_regs = mt2712_ecc_regs,
+	.num_ecc_strength = 11,
+	.ecc_mode_shift = 5,
+	.parity_bits = 14,
+	.pg_irq_sel = 1,
+};
+
 static const struct of_device_id mtk_ecc_dt_match[] = {
 	{
 		.compatible = "mediatek,mt2701-ecc",
@@ -493,6 +512,9 @@ static const struct of_device_id mtk_ecc_dt_match[] = {
 	}, {
 		.compatible = "mediatek,mt7622-ecc",
 		.data = &mtk_ecc_caps_mt7622,
+	}, {
+		.compatible = "mediatek,mt7986-ecc",
+		.data = &mtk_ecc_caps_mt7986,
 	},
 	{},
 };
-- 
2.25.1

[PATCH v4 3/9] mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC

[Xiangsheng Hou]

Add ECC support fot MT7986 IC, and change err_mask value with
GENMASK macro.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 drivers/mtd/nand/ecc-mtk.c | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/ecc-mtk.c b/drivers/mtd/nand/ecc-mtk.c
index 9f9b201fe706..c75bb8b80cc1 100644
--- a/drivers/mtd/nand/ecc-mtk.c
+++ b/drivers/mtd/nand/ecc-mtk.c
@@ -40,6 +40,10 @@
 #define ECC_IDLE_REG(op)	((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE)
 #define ECC_CTL_REG(op)		((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON)
 
+#define ECC_ERRMASK_MT7622	GENMASK(4, 0)
+#define ECC_ERRMASK_MT2701	GENMASK(5, 0)
+#define ECC_ERRMASK_MT2712	GENMASK(6, 0)
+
 struct mtk_ecc_caps {
 	u32 err_mask;
 	u32 err_shift;
@@ -79,6 +83,10 @@ static const u8 ecc_strength_mt7622[] = {
 	4, 6, 8, 10, 12
 };
 
+static const u8 ecc_strength_mt7986[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
+};
+
 enum mtk_ecc_regs {
 	ECC_ENCPAR00,
 	ECC_ENCIRQ_EN,
@@ -451,7 +459,7 @@ unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc)
 EXPORT_SYMBOL(mtk_ecc_get_parity_bits);
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
-	.err_mask = 0x3f,
+	.err_mask = ECC_ERRMASK_MT2701,
 	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2701,
 	.ecc_regs = mt2701_ecc_regs,
@@ -462,7 +470,7 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
-	.err_mask = 0x7f,
+	.err_mask = ECC_ERRMASK_MT2712,
 	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2712,
 	.ecc_regs = mt2712_ecc_regs,
@@ -473,7 +481,7 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
-	.err_mask = 0x1f,
+	.err_mask = ECC_ERRMASK_MT7622,
 	.err_shift = 5,
 	.ecc_strength = ecc_strength_mt7622,
 	.ecc_regs = mt7622_ecc_regs,
@@ -483,6 +491,17 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
 	.pg_irq_sel = 0,
 };
 
+static const struct mtk_ecc_caps mtk_ecc_caps_mt7986 = {
+	.err_mask = ECC_ERRMASK_MT7622,
+	.err_shift = 8,
+	.ecc_strength = ecc_strength_mt7986,
+	.ecc_regs = mt2712_ecc_regs,
+	.num_ecc_strength = 11,
+	.ecc_mode_shift = 5,
+	.parity_bits = 14,
+	.pg_irq_sel = 1,
+};
+
 static const struct of_device_id mtk_ecc_dt_match[] = {
 	{
 		.compatible = "mediatek,mt2701-ecc",
@@ -493,6 +512,9 @@ static const struct of_device_id mtk_ecc_dt_match[] = {
 	}, {
 		.compatible = "mediatek,mt7622-ecc",
 		.data = &mtk_ecc_caps_mt7622,
+	}, {
+		.compatible = "mediatek,mt7986-ecc",
+		.data = &mtk_ecc_caps_mt7986,
 	},
 	{},
 };
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 3/9] mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC

[Xiangsheng Hou]

Add ECC support fot MT7986 IC, and change err_mask value with
GENMASK macro.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 drivers/mtd/nand/ecc-mtk.c | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/ecc-mtk.c b/drivers/mtd/nand/ecc-mtk.c
index 9f9b201fe706..c75bb8b80cc1 100644
--- a/drivers/mtd/nand/ecc-mtk.c
+++ b/drivers/mtd/nand/ecc-mtk.c
@@ -40,6 +40,10 @@
 #define ECC_IDLE_REG(op)	((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE)
 #define ECC_CTL_REG(op)		((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON)
 
+#define ECC_ERRMASK_MT7622	GENMASK(4, 0)
+#define ECC_ERRMASK_MT2701	GENMASK(5, 0)
+#define ECC_ERRMASK_MT2712	GENMASK(6, 0)
+
 struct mtk_ecc_caps {
 	u32 err_mask;
 	u32 err_shift;
@@ -79,6 +83,10 @@ static const u8 ecc_strength_mt7622[] = {
 	4, 6, 8, 10, 12
 };
 
+static const u8 ecc_strength_mt7986[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24
+};
+
 enum mtk_ecc_regs {
 	ECC_ENCPAR00,
 	ECC_ENCIRQ_EN,
@@ -451,7 +459,7 @@ unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc)
 EXPORT_SYMBOL(mtk_ecc_get_parity_bits);
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
-	.err_mask = 0x3f,
+	.err_mask = ECC_ERRMASK_MT2701,
 	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2701,
 	.ecc_regs = mt2701_ecc_regs,
@@ -462,7 +470,7 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
-	.err_mask = 0x7f,
+	.err_mask = ECC_ERRMASK_MT2712,
 	.err_shift = 8,
 	.ecc_strength = ecc_strength_mt2712,
 	.ecc_regs = mt2712_ecc_regs,
@@ -473,7 +481,7 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
 };
 
 static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
-	.err_mask = 0x1f,
+	.err_mask = ECC_ERRMASK_MT7622,
 	.err_shift = 5,
 	.ecc_strength = ecc_strength_mt7622,
 	.ecc_regs = mt7622_ecc_regs,
@@ -483,6 +491,17 @@ static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = {
 	.pg_irq_sel = 0,
 };
 
+static const struct mtk_ecc_caps mtk_ecc_caps_mt7986 = {
+	.err_mask = ECC_ERRMASK_MT7622,
+	.err_shift = 8,
+	.ecc_strength = ecc_strength_mt7986,
+	.ecc_regs = mt2712_ecc_regs,
+	.num_ecc_strength = 11,
+	.ecc_mode_shift = 5,
+	.parity_bits = 14,
+	.pg_irq_sel = 1,
+};
+
 static const struct of_device_id mtk_ecc_dt_match[] = {
 	{
 		.compatible = "mediatek,mt2701-ecc",
@@ -493,6 +512,9 @@ static const struct of_device_id mtk_ecc_dt_match[] = {
 	}, {
 		.compatible = "mediatek,mt7622-ecc",
 		.data = &mtk_ecc_caps_mt7622,
+	}, {
+		.compatible = "mediatek,mt7986-ecc",
+		.data = &mtk_ecc_caps_mt7986,
 	},
 	{},
 };
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 3/9] mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add ECC support fot MT7986 IC, and change err_mask value with
> GENMASK macro.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v4 3/9] mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add ECC support fot MT7986 IC, and change err_mask value with
> GENMASK macro.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 3/9] mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add ECC support fot MT7986 IC, and change err_mask value with
> GENMASK macro.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 4/9] dt-bindings: spi: mtk-snfi: Add compatible for MT7986

[Xiangsheng Hou]

Add dt-bindings documentation of SPI NAND controller
for MediaTek MT7986 SoC platform. And add optional
nfi_hclk property which is needed for MT7986.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/spi/mediatek,spi-mtk-snfi.yaml   | 51 +++++++++++++++----
 1 file changed, 42 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
index 6e6e02c91780..bab23f1b11fd 100644
--- a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
@@ -18,14 +18,12 @@ description: |
   using the accompanying ECC engine. There should be only one spi
   slave device following generic spi bindings.
 
-allOf:
-  - $ref: /schemas/spi/spi-controller.yaml#
-
 properties:
   compatible:
     enum:
       - mediatek,mt7622-snand
       - mediatek,mt7629-snand
+      - mediatek,mt7986-snand
 
   reg:
     items:
@@ -36,14 +34,12 @@ properties:
       - description: NFI interrupt
 
   clocks:
-    items:
-      - description: clock used for the controller
-      - description: clock used for the SPI bus
+    minItems: 2
+    maxItems: 3
 
   clock-names:
-    items:
-      - const: nfi_clk
-      - const: pad_clk
+    minItems: 2
+    maxItems: 3
 
   nand-ecc-engine:
     description: device-tree node of the accompanying ECC engine.
@@ -57,6 +53,43 @@ required:
   - clock-names
   - nand-ecc-engine
 
+allOf:
+  - $ref: /schemas/spi/spi-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          enum:
+            - mediatek,mt7622-snand
+            - mediatek,mt7629-snand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: clock used for the controller
+            - description: clock used for the SPI bus
+        clock-names:
+          items:
+            - const: nfi_clk
+            - const: pad_clk
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - mediatek,mt7986-snand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: clock used for the controller
+            - description: clock used for the SPI bus
+            - description: clock used for the AHB bus
+        clock-names:
+          items:
+            - const: nfi_clk
+            - const: pad_clk
+            - const: nfi_hclk
+
 unevaluatedProperties: false
 
 examples:
-- 
2.25.1

[PATCH v4 4/9] dt-bindings: spi: mtk-snfi: Add compatible for MT7986

[Xiangsheng Hou]

Add dt-bindings documentation of SPI NAND controller
for MediaTek MT7986 SoC platform. And add optional
nfi_hclk property which is needed for MT7986.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/spi/mediatek,spi-mtk-snfi.yaml   | 51 +++++++++++++++----
 1 file changed, 42 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
index 6e6e02c91780..bab23f1b11fd 100644
--- a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
@@ -18,14 +18,12 @@ description: |
   using the accompanying ECC engine. There should be only one spi
   slave device following generic spi bindings.
 
-allOf:
-  - $ref: /schemas/spi/spi-controller.yaml#
-
 properties:
   compatible:
     enum:
       - mediatek,mt7622-snand
       - mediatek,mt7629-snand
+      - mediatek,mt7986-snand
 
   reg:
     items:
@@ -36,14 +34,12 @@ properties:
       - description: NFI interrupt
 
   clocks:
-    items:
-      - description: clock used for the controller
-      - description: clock used for the SPI bus
+    minItems: 2
+    maxItems: 3
 
   clock-names:
-    items:
-      - const: nfi_clk
-      - const: pad_clk
+    minItems: 2
+    maxItems: 3
 
   nand-ecc-engine:
     description: device-tree node of the accompanying ECC engine.
@@ -57,6 +53,43 @@ required:
   - clock-names
   - nand-ecc-engine
 
+allOf:
+  - $ref: /schemas/spi/spi-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          enum:
+            - mediatek,mt7622-snand
+            - mediatek,mt7629-snand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: clock used for the controller
+            - description: clock used for the SPI bus
+        clock-names:
+          items:
+            - const: nfi_clk
+            - const: pad_clk
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - mediatek,mt7986-snand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: clock used for the controller
+            - description: clock used for the SPI bus
+            - description: clock used for the AHB bus
+        clock-names:
+          items:
+            - const: nfi_clk
+            - const: pad_clk
+            - const: nfi_hclk
+
 unevaluatedProperties: false
 
 examples:
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 4/9] dt-bindings: spi: mtk-snfi: Add compatible for MT7986

[Xiangsheng Hou]

Add dt-bindings documentation of SPI NAND controller
for MediaTek MT7986 SoC platform. And add optional
nfi_hclk property which is needed for MT7986.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/spi/mediatek,spi-mtk-snfi.yaml   | 51 +++++++++++++++----
 1 file changed, 42 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
index 6e6e02c91780..bab23f1b11fd 100644
--- a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
@@ -18,14 +18,12 @@ description: |
   using the accompanying ECC engine. There should be only one spi
   slave device following generic spi bindings.
 
-allOf:
-  - $ref: /schemas/spi/spi-controller.yaml#
-
 properties:
   compatible:
     enum:
       - mediatek,mt7622-snand
       - mediatek,mt7629-snand
+      - mediatek,mt7986-snand
 
   reg:
     items:
@@ -36,14 +34,12 @@ properties:
       - description: NFI interrupt
 
   clocks:
-    items:
-      - description: clock used for the controller
-      - description: clock used for the SPI bus
+    minItems: 2
+    maxItems: 3
 
   clock-names:
-    items:
-      - const: nfi_clk
-      - const: pad_clk
+    minItems: 2
+    maxItems: 3
 
   nand-ecc-engine:
     description: device-tree node of the accompanying ECC engine.
@@ -57,6 +53,43 @@ required:
   - clock-names
   - nand-ecc-engine
 
+allOf:
+  - $ref: /schemas/spi/spi-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          enum:
+            - mediatek,mt7622-snand
+            - mediatek,mt7629-snand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: clock used for the controller
+            - description: clock used for the SPI bus
+        clock-names:
+          items:
+            - const: nfi_clk
+            - const: pad_clk
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - mediatek,mt7986-snand
+    then:
+      properties:
+        clocks:
+          items:
+            - description: clock used for the controller
+            - description: clock used for the SPI bus
+            - description: clock used for the AHB bus
+        clock-names:
+          items:
+            - const: nfi_clk
+            - const: pad_clk
+            - const: nfi_hclk
+
 unevaluatedProperties: false
 
 examples:
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 4/9] dt-bindings: spi: mtk-snfi: Add compatible for MT7986

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add dt-bindings documentation of SPI NAND controller
> for MediaTek MT7986 SoC platform. And add optional
> nfi_hclk property which is needed for MT7986.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v4 4/9] dt-bindings: spi: mtk-snfi: Add compatible for MT7986

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add dt-bindings documentation of SPI NAND controller
> for MediaTek MT7986 SoC platform. And add optional
> nfi_hclk property which is needed for MT7986.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 4/9] dt-bindings: spi: mtk-snfi: Add compatible for MT7986

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add dt-bindings documentation of SPI NAND controller
> for MediaTek MT7986 SoC platform. And add optional
> nfi_hclk property which is needed for MT7986.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 5/9] spi: mtk-snfi: Add snfi sample delay and read latency adjustment

[Xiangsheng Hou]

Add snfi sample delay and read latency adjustment which can get
from dts property.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/spi/spi-mtk-snfi.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index 85644308df23..f3f95eb37365 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -195,6 +195,8 @@
 #define DATA_READ_MODE_X4 2
 #define DATA_READ_MODE_DUAL 5
 #define DATA_READ_MODE_QUAD 6
+#define DATA_READ_LATCH_LAT GENMASK(9, 8)
+#define DATA_READ_LATCH_LAT_S 8
 #define PG_LOAD_CUSTOM_EN BIT(7)
 #define DATARD_CUSTOM_EN BIT(6)
 #define CS_DESELECT_CYC_S 0
@@ -205,6 +207,9 @@
 
 #define SNF_DLY_CTL3 0x548
 #define SFCK_SAM_DLY_S 0
+#define SFCK_SAM_DLY GENMASK(5, 0)
+#define SFCK_SAM_DLY_TOTAL 9
+#define SFCK_SAM_DLY_RANGE 47
 
 #define SNF_STA_CTL1 0x550
 #define CUS_PG_DONE BIT(28)
@@ -1368,6 +1373,8 @@ static int mtk_snand_probe(struct platform_device *pdev)
 	const struct of_device_id *dev_id;
 	struct spi_controller *ctlr;
 	struct mtk_snand *ms;
+	unsigned long spi_freq;
+	u32 val = 0;
 	int ret;
 
 	dev_id = of_match_node(mtk_snand_ids, np);
@@ -1446,6 +1453,19 @@ static int mtk_snand_probe(struct platform_device *pdev)
 	// switch to SNFI mode
 	nfi_write32(ms, SNF_CFG, SPI_MODE);
 
+	ret = of_property_read_u32(np, "rx-sample-delay-ns", &val);
+	if (!ret)
+		nfi_rmw32(ms, SNF_DLY_CTL3, SFCK_SAM_DLY,
+			  val * SFCK_SAM_DLY_RANGE / SFCK_SAM_DLY_TOTAL);
+
+	ret = of_property_read_u32(np, "mediatek,rx-latch-latency-ns", &val);
+	if (!ret) {
+		spi_freq = clk_get_rate(ms->pad_clk);
+		val = DIV_ROUND_CLOSEST(val, NSEC_PER_SEC / spi_freq);
+		nfi_rmw32(ms, SNF_MISC_CTL, DATA_READ_LATCH_LAT,
+			  val << DATA_READ_LATCH_LAT_S);
+	}
+
 	// setup an initial page format for ops matching page_cache_op template
 	// before ECC is called.
 	ret = mtk_snand_setup_pagefmt(ms, SZ_2K, SZ_64);
-- 
2.25.1

[PATCH v4 5/9] spi: mtk-snfi: Add snfi sample delay and read latency adjustment

[Xiangsheng Hou]

Add snfi sample delay and read latency adjustment which can get
from dts property.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/spi/spi-mtk-snfi.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index 85644308df23..f3f95eb37365 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -195,6 +195,8 @@
 #define DATA_READ_MODE_X4 2
 #define DATA_READ_MODE_DUAL 5
 #define DATA_READ_MODE_QUAD 6
+#define DATA_READ_LATCH_LAT GENMASK(9, 8)
+#define DATA_READ_LATCH_LAT_S 8
 #define PG_LOAD_CUSTOM_EN BIT(7)
 #define DATARD_CUSTOM_EN BIT(6)
 #define CS_DESELECT_CYC_S 0
@@ -205,6 +207,9 @@
 
 #define SNF_DLY_CTL3 0x548
 #define SFCK_SAM_DLY_S 0
+#define SFCK_SAM_DLY GENMASK(5, 0)
+#define SFCK_SAM_DLY_TOTAL 9
+#define SFCK_SAM_DLY_RANGE 47
 
 #define SNF_STA_CTL1 0x550
 #define CUS_PG_DONE BIT(28)
@@ -1368,6 +1373,8 @@ static int mtk_snand_probe(struct platform_device *pdev)
 	const struct of_device_id *dev_id;
 	struct spi_controller *ctlr;
 	struct mtk_snand *ms;
+	unsigned long spi_freq;
+	u32 val = 0;
 	int ret;
 
 	dev_id = of_match_node(mtk_snand_ids, np);
@@ -1446,6 +1453,19 @@ static int mtk_snand_probe(struct platform_device *pdev)
 	// switch to SNFI mode
 	nfi_write32(ms, SNF_CFG, SPI_MODE);
 
+	ret = of_property_read_u32(np, "rx-sample-delay-ns", &val);
+	if (!ret)
+		nfi_rmw32(ms, SNF_DLY_CTL3, SFCK_SAM_DLY,
+			  val * SFCK_SAM_DLY_RANGE / SFCK_SAM_DLY_TOTAL);
+
+	ret = of_property_read_u32(np, "mediatek,rx-latch-latency-ns", &val);
+	if (!ret) {
+		spi_freq = clk_get_rate(ms->pad_clk);
+		val = DIV_ROUND_CLOSEST(val, NSEC_PER_SEC / spi_freq);
+		nfi_rmw32(ms, SNF_MISC_CTL, DATA_READ_LATCH_LAT,
+			  val << DATA_READ_LATCH_LAT_S);
+	}
+
 	// setup an initial page format for ops matching page_cache_op template
 	// before ECC is called.
 	ret = mtk_snand_setup_pagefmt(ms, SZ_2K, SZ_64);
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 5/9] spi: mtk-snfi: Add snfi sample delay and read latency adjustment

[Xiangsheng Hou]

Add snfi sample delay and read latency adjustment which can get
from dts property.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/spi/spi-mtk-snfi.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/spi/spi-mtk-snfi.c b/drivers/spi/spi-mtk-snfi.c
index 85644308df23..f3f95eb37365 100644
--- a/drivers/spi/spi-mtk-snfi.c
+++ b/drivers/spi/spi-mtk-snfi.c
@@ -195,6 +195,8 @@
 #define DATA_READ_MODE_X4 2
 #define DATA_READ_MODE_DUAL 5
 #define DATA_READ_MODE_QUAD 6
+#define DATA_READ_LATCH_LAT GENMASK(9, 8)
+#define DATA_READ_LATCH_LAT_S 8
 #define PG_LOAD_CUSTOM_EN BIT(7)
 #define DATARD_CUSTOM_EN BIT(6)
 #define CS_DESELECT_CYC_S 0
@@ -205,6 +207,9 @@
 
 #define SNF_DLY_CTL3 0x548
 #define SFCK_SAM_DLY_S 0
+#define SFCK_SAM_DLY GENMASK(5, 0)
+#define SFCK_SAM_DLY_TOTAL 9
+#define SFCK_SAM_DLY_RANGE 47
 
 #define SNF_STA_CTL1 0x550
 #define CUS_PG_DONE BIT(28)
@@ -1368,6 +1373,8 @@ static int mtk_snand_probe(struct platform_device *pdev)
 	const struct of_device_id *dev_id;
 	struct spi_controller *ctlr;
 	struct mtk_snand *ms;
+	unsigned long spi_freq;
+	u32 val = 0;
 	int ret;
 
 	dev_id = of_match_node(mtk_snand_ids, np);
@@ -1446,6 +1453,19 @@ static int mtk_snand_probe(struct platform_device *pdev)
 	// switch to SNFI mode
 	nfi_write32(ms, SNF_CFG, SPI_MODE);
 
+	ret = of_property_read_u32(np, "rx-sample-delay-ns", &val);
+	if (!ret)
+		nfi_rmw32(ms, SNF_DLY_CTL3, SFCK_SAM_DLY,
+			  val * SFCK_SAM_DLY_RANGE / SFCK_SAM_DLY_TOTAL);
+
+	ret = of_property_read_u32(np, "mediatek,rx-latch-latency-ns", &val);
+	if (!ret) {
+		spi_freq = clk_get_rate(ms->pad_clk);
+		val = DIV_ROUND_CLOSEST(val, NSEC_PER_SEC / spi_freq);
+		nfi_rmw32(ms, SNF_MISC_CTL, DATA_READ_LATCH_LAT,
+			  val << DATA_READ_LATCH_LAT_S);
+	}
+
 	// setup an initial page format for ops matching page_cache_op template
 	// before ECC is called.
 	ret = mtk_snand_setup_pagefmt(ms, SZ_2K, SZ_64);
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 6/9] dt-bindings: spi: mtk-snfi: Add read latch latency property

[Xiangsheng Hou]

Add mediatek,rx-latch-latency-ns property which adjust data read
latch latency in the unit of nanoseconds.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml         | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
index bab23f1b11fd..1e5e89a693c3 100644
--- a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
@@ -45,6 +45,9 @@ properties:
     description: device-tree node of the accompanying ECC engine.
     $ref: /schemas/types.yaml#/definitions/phandle
 
+  mediatek,rx-latch-latency-ns:
+    description: Data read latch latency, unit is nanoseconds.
+
 required:
   - compatible
   - reg
-- 
2.25.1

[PATCH v4 6/9] dt-bindings: spi: mtk-snfi: Add read latch latency property

[Xiangsheng Hou]

Add mediatek,rx-latch-latency-ns property which adjust data read
latch latency in the unit of nanoseconds.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml         | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
index bab23f1b11fd..1e5e89a693c3 100644
--- a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
@@ -45,6 +45,9 @@ properties:
     description: device-tree node of the accompanying ECC engine.
     $ref: /schemas/types.yaml#/definitions/phandle
 
+  mediatek,rx-latch-latency-ns:
+    description: Data read latch latency, unit is nanoseconds.
+
 required:
   - compatible
   - reg
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 6/9] dt-bindings: spi: mtk-snfi: Add read latch latency property

[Xiangsheng Hou]

Add mediatek,rx-latch-latency-ns property which adjust data read
latch latency in the unit of nanoseconds.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml         | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
index bab23f1b11fd..1e5e89a693c3 100644
--- a/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mtk-snfi.yaml
@@ -45,6 +45,9 @@ properties:
     description: device-tree node of the accompanying ECC engine.
     $ref: /schemas/types.yaml#/definitions/phandle
 
+  mediatek,rx-latch-latency-ns:
+    description: Data read latch latency, unit is nanoseconds.
+
 required:
   - compatible
   - reg
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 6/9] dt-bindings: spi: mtk-snfi: Add read latch latency property

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add mediatek,rx-latch-latency-ns property which adjust data read
> latch latency in the unit of nanoseconds.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v4 6/9] dt-bindings: spi: mtk-snfi: Add read latch latency property

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add mediatek,rx-latch-latency-ns property which adjust data read
> latch latency in the unit of nanoseconds.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 6/9] dt-bindings: spi: mtk-snfi: Add read latch latency property

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Add mediatek,rx-latch-latency-ns property which adjust data read
> latch latency in the unit of nanoseconds.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 7/9] dt-bindings: mtd: Split ECC engine with rawnand controller

[Xiangsheng Hou]

Split MediaTek ECC engine with rawnand controller and convert to
YAML schema.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 .../bindings/mtd/mediatek,mtk-nfc.yaml        | 155 +++++++++++++++
 .../mtd/mediatek,nand-ecc-engine.yaml         |  62 ++++++
 .../devicetree/bindings/mtd/mtk-nand.txt      | 176 ------------------
 3 files changed, 217 insertions(+), 176 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
 delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

diff --git a/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
new file mode 100644
index 000000000000..a6e7f123eda7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mediatek,mtk-nfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC)
+
+maintainers:
+  - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-nfc
+      - mediatek,mt2712-nfc
+      - mediatek,mt7622-nfc
+
+  reg:
+    items:
+      - description: Base physical address and size of NFI.
+
+  interrupts:
+    items:
+      - description: NFI interrupt
+
+  clocks:
+    items:
+      - description: clock used for the controller
+      - description: clock used for the pad
+
+  clock-names:
+    items:
+      - const: nfi_clk
+      - const: pad_clk
+
+  ecc-engine:
+    description: device-tree node of the required ECC engine.
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+patternProperties:
+  "^nand@[a-f0-9]$":
+    $ref: nand-chip.yaml#
+    unevaluatedProperties: false
+    properties:
+      reg:
+        maximum: 1
+      nand-on-flash-bbt: true
+      nand-ecc-mode:
+        const: hw
+
+allOf:
+  - $ref: nand-controller.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt2701-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              enum: [ 512, 1024 ]
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+                     40, 44, 48, 52, 56, 60]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt2712-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              enum: [ 512, 1024 ]
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+                     40, 44, 48, 52, 56, 60, 68, 72, 80]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt7622-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              const: 512
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - ecc-engine
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        nand-controller@1100d000 {
+            compatible = "mediatek,mt2701-nfc";
+            reg = <0 0x1100d000 0 0x1000>;
+            interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&pericfg CLK_PERI_NFI>,
+                     <&pericfg CLK_PERI_NFI_PAD>;
+            clock-names = "nfi_clk", "pad_clk";
+            ecc-engine = <&bch>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            nand@0 {
+                reg = <0>;
+
+                nand-on-flash-bbt;
+                nand-ecc-mode = "hw";
+                nand-ecc-step-size = <1024>;
+                nand-ecc-strength = <24>;
+
+                partitions {
+                    compatible = "fixed-partitions";
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+
+                    preloader@0 {
+                        label = "pl";
+                        read-only;
+                        reg = <0x0 0x400000>;
+                    };
+                    android@400000 {
+                        label = "android";
+                        reg = <0x400000 0x12c00000>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
new file mode 100644
index 000000000000..b13d801eda76
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mediatek,nand-ecc-engine.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs NAND ECC engine
+
+maintainers:
+  - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
+
+description: |
+  MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-ecc
+      - mediatek,mt2712-ecc
+      - mediatek,mt7622-ecc
+
+  reg:
+    items:
+      - description: Base physical address and size of ECC.
+
+  interrupts:
+    items:
+      - description: ECC interrupt
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: nfiecc_clk
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        bch: ecc@1100e000 {
+            compatible = "mediatek,mt2701-ecc";
+            reg = <0 0x1100e000 0 0x1000>;
+            interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&pericfg CLK_PERI_NFI_ECC>;
+            clock-names = "nfiecc_clk";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
deleted file mode 100644
index 839ea2f93d04..000000000000
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-MTK SoCs NAND FLASH controller (NFC) DT binding
-
-This file documents the device tree bindings for MTK SoCs NAND controllers.
-The functional split of the controller requires two drivers to operate:
-the nand controller interface driver and the ECC engine driver.
-
-The hardware description for both devices must be captured as device
-tree nodes.
-
-1) NFC NAND Controller Interface (NFI):
-=======================================
-
-The first part of NFC is NAND Controller Interface (NFI) HW.
-Required NFI properties:
-- compatible:			Should be one of
-				"mediatek,mt2701-nfc",
-				"mediatek,mt2712-nfc",
-				"mediatek,mt7622-nfc".
-- reg:				Base physical address and size of NFI.
-- interrupts:			Interrupts of NFI.
-- clocks:			NFI required clocks.
-- clock-names:			NFI clocks internal name.
-- ecc-engine:			Required ECC Engine node.
-- #address-cells:		NAND chip index, should be 1.
-- #size-cells:			Should be 0.
-
-Example:
-
-	nandc: nfi@1100d000 {
-		compatible = "mediatek,mt2701-nfc";
-		reg = <0 0x1100d000 0 0x1000>;
-		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&pericfg CLK_PERI_NFI>,
-			 <&pericfg CLK_PERI_NFI_PAD>;
-		clock-names = "nfi_clk", "pad_clk";
-		ecc-engine = <&bch>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-        };
-
-Platform related properties, should be set in {platform_name}.dts:
-- children nodes:	NAND chips.
-
-Children nodes properties:
-- reg:			Chip Select Signal, default 0.
-			Set as reg = <0>, <1> when need 2 CS.
-Optional:
-- nand-on-flash-bbt:	Store BBT on NAND Flash.
-- nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
-- nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
-			valid values:
-			512 and 1024 on mt2701 and mt2712.
-			512 only on mt7622.
-			1024 is recommended for large page NANDs.
-- nand-ecc-strength:	Number of bits to correct per ECC step.
-			The valid values that each controller supports:
-			mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
-				32, 36, 40, 44, 48, 52, 56, 60.
-			mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
-				32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80.
-			mt7622: 4, 6, 8, 10, 12, 14, 16.
-			The strength should be calculated as follows:
-			E = (S - F) * 8 / B
-			S = O / (P / Q)
-				E :	nand-ecc-strength.
-				S :	spare size per sector.
-				F :	FDM size, should be in the range [1,8].
-					It is used to store free oob data.
-				O :	oob size.
-				P :	page size.
-				Q :	nand-ecc-step-size.
-				B :	number of parity bits needed to correct
-					1 bitflip.
-					According to MTK NAND controller design,
-					this number depends on max ecc step size
-					that MTK NAND controller supports.
-					If max ecc step size supported is 1024,
-					then it should be always 14. And if max
-					ecc step size is 512, then it should be
-					always 13.
-			If the result does not match any one of the listed
-			choices above, please select the smaller valid value from
-			the list.
-			(otherwise the driver will do the adjustment at runtime)
-- pinctrl-names:	Default NAND pin GPIO setting name.
-- pinctrl-0:		GPIO setting node.
-
-Example:
-	&pio {
-		nand_pins_default: nanddefault {
-			pins_dat {
-				pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
-					 <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
-					 <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
-					 <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
-					 <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
-					 <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
-					 <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
-					 <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
-					 <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
-				input-enable;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-up;
-			};
-
-			pins_we {
-				pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
-			};
-
-			pins_ale {
-				pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
-			};
-		};
-	};
-
-	&nandc {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&nand_pins_default>;
-		nand@0 {
-			reg = <0>;
-			nand-on-flash-bbt;
-			nand-ecc-mode = "hw";
-			nand-ecc-strength = <24>;
-			nand-ecc-step-size = <1024>;
-		};
-	};
-
-NAND chip optional subnodes:
-- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml
-
-Example:
-	nand@0 {
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			preloader@0 {
-				label = "pl";
-				read-only;
-				reg = <0x00000000 0x00400000>;
-			};
-			android@00400000 {
-				label = "android";
-				reg = <0x00400000 0x12c00000>;
-			};
-		};
-	};
-
-2) ECC Engine:
-==============
-
-Required BCH properties:
-- compatible:	Should be one of
-		"mediatek,mt2701-ecc",
-		"mediatek,mt2712-ecc",
-		"mediatek,mt7622-ecc".
-- reg:		Base physical address and size of ECC.
-- interrupts:	Interrupts of ECC.
-- clocks:	ECC required clocks.
-- clock-names:	ECC clocks internal name.
-
-Example:
-
-	bch: ecc@1100e000 {
-		compatible = "mediatek,mt2701-ecc";
-		reg = <0 0x1100e000 0 0x1000>;
-		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&pericfg CLK_PERI_NFI_ECC>;
-		clock-names = "nfiecc_clk";
-	};
-- 
2.25.1

[PATCH v4 7/9] dt-bindings: mtd: Split ECC engine with rawnand controller

[Xiangsheng Hou]

Split MediaTek ECC engine with rawnand controller and convert to
YAML schema.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 .../bindings/mtd/mediatek,mtk-nfc.yaml        | 155 +++++++++++++++
 .../mtd/mediatek,nand-ecc-engine.yaml         |  62 ++++++
 .../devicetree/bindings/mtd/mtk-nand.txt      | 176 ------------------
 3 files changed, 217 insertions(+), 176 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
 delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

diff --git a/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
new file mode 100644
index 000000000000..a6e7f123eda7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mediatek,mtk-nfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC)
+
+maintainers:
+  - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-nfc
+      - mediatek,mt2712-nfc
+      - mediatek,mt7622-nfc
+
+  reg:
+    items:
+      - description: Base physical address and size of NFI.
+
+  interrupts:
+    items:
+      - description: NFI interrupt
+
+  clocks:
+    items:
+      - description: clock used for the controller
+      - description: clock used for the pad
+
+  clock-names:
+    items:
+      - const: nfi_clk
+      - const: pad_clk
+
+  ecc-engine:
+    description: device-tree node of the required ECC engine.
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+patternProperties:
+  "^nand@[a-f0-9]$":
+    $ref: nand-chip.yaml#
+    unevaluatedProperties: false
+    properties:
+      reg:
+        maximum: 1
+      nand-on-flash-bbt: true
+      nand-ecc-mode:
+        const: hw
+
+allOf:
+  - $ref: nand-controller.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt2701-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              enum: [ 512, 1024 ]
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+                     40, 44, 48, 52, 56, 60]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt2712-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              enum: [ 512, 1024 ]
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+                     40, 44, 48, 52, 56, 60, 68, 72, 80]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt7622-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              const: 512
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - ecc-engine
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        nand-controller@1100d000 {
+            compatible = "mediatek,mt2701-nfc";
+            reg = <0 0x1100d000 0 0x1000>;
+            interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&pericfg CLK_PERI_NFI>,
+                     <&pericfg CLK_PERI_NFI_PAD>;
+            clock-names = "nfi_clk", "pad_clk";
+            ecc-engine = <&bch>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            nand@0 {
+                reg = <0>;
+
+                nand-on-flash-bbt;
+                nand-ecc-mode = "hw";
+                nand-ecc-step-size = <1024>;
+                nand-ecc-strength = <24>;
+
+                partitions {
+                    compatible = "fixed-partitions";
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+
+                    preloader@0 {
+                        label = "pl";
+                        read-only;
+                        reg = <0x0 0x400000>;
+                    };
+                    android@400000 {
+                        label = "android";
+                        reg = <0x400000 0x12c00000>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
new file mode 100644
index 000000000000..b13d801eda76
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mediatek,nand-ecc-engine.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs NAND ECC engine
+
+maintainers:
+  - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
+
+description: |
+  MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-ecc
+      - mediatek,mt2712-ecc
+      - mediatek,mt7622-ecc
+
+  reg:
+    items:
+      - description: Base physical address and size of ECC.
+
+  interrupts:
+    items:
+      - description: ECC interrupt
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: nfiecc_clk
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        bch: ecc@1100e000 {
+            compatible = "mediatek,mt2701-ecc";
+            reg = <0 0x1100e000 0 0x1000>;
+            interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&pericfg CLK_PERI_NFI_ECC>;
+            clock-names = "nfiecc_clk";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
deleted file mode 100644
index 839ea2f93d04..000000000000
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-MTK SoCs NAND FLASH controller (NFC) DT binding
-
-This file documents the device tree bindings for MTK SoCs NAND controllers.
-The functional split of the controller requires two drivers to operate:
-the nand controller interface driver and the ECC engine driver.
-
-The hardware description for both devices must be captured as device
-tree nodes.
-
-1) NFC NAND Controller Interface (NFI):
-=======================================
-
-The first part of NFC is NAND Controller Interface (NFI) HW.
-Required NFI properties:
-- compatible:			Should be one of
-				"mediatek,mt2701-nfc",
-				"mediatek,mt2712-nfc",
-				"mediatek,mt7622-nfc".
-- reg:				Base physical address and size of NFI.
-- interrupts:			Interrupts of NFI.
-- clocks:			NFI required clocks.
-- clock-names:			NFI clocks internal name.
-- ecc-engine:			Required ECC Engine node.
-- #address-cells:		NAND chip index, should be 1.
-- #size-cells:			Should be 0.
-
-Example:
-
-	nandc: nfi@1100d000 {
-		compatible = "mediatek,mt2701-nfc";
-		reg = <0 0x1100d000 0 0x1000>;
-		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&pericfg CLK_PERI_NFI>,
-			 <&pericfg CLK_PERI_NFI_PAD>;
-		clock-names = "nfi_clk", "pad_clk";
-		ecc-engine = <&bch>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-        };
-
-Platform related properties, should be set in {platform_name}.dts:
-- children nodes:	NAND chips.
-
-Children nodes properties:
-- reg:			Chip Select Signal, default 0.
-			Set as reg = <0>, <1> when need 2 CS.
-Optional:
-- nand-on-flash-bbt:	Store BBT on NAND Flash.
-- nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
-- nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
-			valid values:
-			512 and 1024 on mt2701 and mt2712.
-			512 only on mt7622.
-			1024 is recommended for large page NANDs.
-- nand-ecc-strength:	Number of bits to correct per ECC step.
-			The valid values that each controller supports:
-			mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
-				32, 36, 40, 44, 48, 52, 56, 60.
-			mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
-				32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80.
-			mt7622: 4, 6, 8, 10, 12, 14, 16.
-			The strength should be calculated as follows:
-			E = (S - F) * 8 / B
-			S = O / (P / Q)
-				E :	nand-ecc-strength.
-				S :	spare size per sector.
-				F :	FDM size, should be in the range [1,8].
-					It is used to store free oob data.
-				O :	oob size.
-				P :	page size.
-				Q :	nand-ecc-step-size.
-				B :	number of parity bits needed to correct
-					1 bitflip.
-					According to MTK NAND controller design,
-					this number depends on max ecc step size
-					that MTK NAND controller supports.
-					If max ecc step size supported is 1024,
-					then it should be always 14. And if max
-					ecc step size is 512, then it should be
-					always 13.
-			If the result does not match any one of the listed
-			choices above, please select the smaller valid value from
-			the list.
-			(otherwise the driver will do the adjustment at runtime)
-- pinctrl-names:	Default NAND pin GPIO setting name.
-- pinctrl-0:		GPIO setting node.
-
-Example:
-	&pio {
-		nand_pins_default: nanddefault {
-			pins_dat {
-				pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
-					 <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
-					 <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
-					 <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
-					 <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
-					 <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
-					 <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
-					 <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
-					 <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
-				input-enable;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-up;
-			};
-
-			pins_we {
-				pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
-			};
-
-			pins_ale {
-				pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
-			};
-		};
-	};
-
-	&nandc {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&nand_pins_default>;
-		nand@0 {
-			reg = <0>;
-			nand-on-flash-bbt;
-			nand-ecc-mode = "hw";
-			nand-ecc-strength = <24>;
-			nand-ecc-step-size = <1024>;
-		};
-	};
-
-NAND chip optional subnodes:
-- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml
-
-Example:
-	nand@0 {
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			preloader@0 {
-				label = "pl";
-				read-only;
-				reg = <0x00000000 0x00400000>;
-			};
-			android@00400000 {
-				label = "android";
-				reg = <0x00400000 0x12c00000>;
-			};
-		};
-	};
-
-2) ECC Engine:
-==============
-
-Required BCH properties:
-- compatible:	Should be one of
-		"mediatek,mt2701-ecc",
-		"mediatek,mt2712-ecc",
-		"mediatek,mt7622-ecc".
-- reg:		Base physical address and size of ECC.
-- interrupts:	Interrupts of ECC.
-- clocks:	ECC required clocks.
-- clock-names:	ECC clocks internal name.
-
-Example:
-
-	bch: ecc@1100e000 {
-		compatible = "mediatek,mt2701-ecc";
-		reg = <0 0x1100e000 0 0x1000>;
-		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&pericfg CLK_PERI_NFI_ECC>;
-		clock-names = "nfiecc_clk";
-	};
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 7/9] dt-bindings: mtd: Split ECC engine with rawnand controller

[Xiangsheng Hou]

Split MediaTek ECC engine with rawnand controller and convert to
YAML schema.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 .../bindings/mtd/mediatek,mtk-nfc.yaml        | 155 +++++++++++++++
 .../mtd/mediatek,nand-ecc-engine.yaml         |  62 ++++++
 .../devicetree/bindings/mtd/mtk-nand.txt      | 176 ------------------
 3 files changed, 217 insertions(+), 176 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
 create mode 100644 Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
 delete mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt

diff --git a/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
new file mode 100644
index 000000000000..a6e7f123eda7
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mediatek,mtk-nfc.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mediatek,mtk-nfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs raw NAND FLASH controller (NFC)
+
+maintainers:
+  - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-nfc
+      - mediatek,mt2712-nfc
+      - mediatek,mt7622-nfc
+
+  reg:
+    items:
+      - description: Base physical address and size of NFI.
+
+  interrupts:
+    items:
+      - description: NFI interrupt
+
+  clocks:
+    items:
+      - description: clock used for the controller
+      - description: clock used for the pad
+
+  clock-names:
+    items:
+      - const: nfi_clk
+      - const: pad_clk
+
+  ecc-engine:
+    description: device-tree node of the required ECC engine.
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+patternProperties:
+  "^nand@[a-f0-9]$":
+    $ref: nand-chip.yaml#
+    unevaluatedProperties: false
+    properties:
+      reg:
+        maximum: 1
+      nand-on-flash-bbt: true
+      nand-ecc-mode:
+        const: hw
+
+allOf:
+  - $ref: nand-controller.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt2701-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              enum: [ 512, 1024 ]
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+                     40, 44, 48, 52, 56, 60]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt2712-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              enum: [ 512, 1024 ]
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+                     40, 44, 48, 52, 56, 60, 68, 72, 80]
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt7622-nfc
+    then:
+      patternProperties:
+        "^nand@[a-f0-9]$":
+          properties:
+            nand-ecc-step-size:
+              const: 512
+            nand-ecc-strength:
+              enum: [4, 6, 8, 10, 12]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - ecc-engine
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        nand-controller@1100d000 {
+            compatible = "mediatek,mt2701-nfc";
+            reg = <0 0x1100d000 0 0x1000>;
+            interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&pericfg CLK_PERI_NFI>,
+                     <&pericfg CLK_PERI_NFI_PAD>;
+            clock-names = "nfi_clk", "pad_clk";
+            ecc-engine = <&bch>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            nand@0 {
+                reg = <0>;
+
+                nand-on-flash-bbt;
+                nand-ecc-mode = "hw";
+                nand-ecc-step-size = <1024>;
+                nand-ecc-strength = <24>;
+
+                partitions {
+                    compatible = "fixed-partitions";
+                    #address-cells = <1>;
+                    #size-cells = <1>;
+
+                    preloader@0 {
+                        label = "pl";
+                        read-only;
+                        reg = <0x0 0x400000>;
+                    };
+                    android@400000 {
+                        label = "android";
+                        reg = <0x400000 0x12c00000>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
new file mode 100644
index 000000000000..b13d801eda76
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/mediatek,nand-ecc-engine.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek(MTK) SoCs NAND ECC engine
+
+maintainers:
+  - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
+
+description: |
+  MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt2701-ecc
+      - mediatek,mt2712-ecc
+      - mediatek,mt7622-ecc
+
+  reg:
+    items:
+      - description: Base physical address and size of ECC.
+
+  interrupts:
+    items:
+      - description: ECC interrupt
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: nfiecc_clk
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2701-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        bch: ecc@1100e000 {
+            compatible = "mediatek,mt2701-ecc";
+            reg = <0 0x1100e000 0 0x1000>;
+            interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
+            clocks = <&pericfg CLK_PERI_NFI_ECC>;
+            clock-names = "nfiecc_clk";
+        };
+    };
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
deleted file mode 100644
index 839ea2f93d04..000000000000
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-MTK SoCs NAND FLASH controller (NFC) DT binding
-
-This file documents the device tree bindings for MTK SoCs NAND controllers.
-The functional split of the controller requires two drivers to operate:
-the nand controller interface driver and the ECC engine driver.
-
-The hardware description for both devices must be captured as device
-tree nodes.
-
-1) NFC NAND Controller Interface (NFI):
-=======================================
-
-The first part of NFC is NAND Controller Interface (NFI) HW.
-Required NFI properties:
-- compatible:			Should be one of
-				"mediatek,mt2701-nfc",
-				"mediatek,mt2712-nfc",
-				"mediatek,mt7622-nfc".
-- reg:				Base physical address and size of NFI.
-- interrupts:			Interrupts of NFI.
-- clocks:			NFI required clocks.
-- clock-names:			NFI clocks internal name.
-- ecc-engine:			Required ECC Engine node.
-- #address-cells:		NAND chip index, should be 1.
-- #size-cells:			Should be 0.
-
-Example:
-
-	nandc: nfi@1100d000 {
-		compatible = "mediatek,mt2701-nfc";
-		reg = <0 0x1100d000 0 0x1000>;
-		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&pericfg CLK_PERI_NFI>,
-			 <&pericfg CLK_PERI_NFI_PAD>;
-		clock-names = "nfi_clk", "pad_clk";
-		ecc-engine = <&bch>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-        };
-
-Platform related properties, should be set in {platform_name}.dts:
-- children nodes:	NAND chips.
-
-Children nodes properties:
-- reg:			Chip Select Signal, default 0.
-			Set as reg = <0>, <1> when need 2 CS.
-Optional:
-- nand-on-flash-bbt:	Store BBT on NAND Flash.
-- nand-ecc-mode:	the NAND ecc mode (check driver for supported modes)
-- nand-ecc-step-size:	Number of data bytes covered by a single ECC step.
-			valid values:
-			512 and 1024 on mt2701 and mt2712.
-			512 only on mt7622.
-			1024 is recommended for large page NANDs.
-- nand-ecc-strength:	Number of bits to correct per ECC step.
-			The valid values that each controller supports:
-			mt2701: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
-				32, 36, 40, 44, 48, 52, 56, 60.
-			mt2712: 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28,
-				32, 36, 40, 44, 48, 52, 56, 60, 68, 72, 80.
-			mt7622: 4, 6, 8, 10, 12, 14, 16.
-			The strength should be calculated as follows:
-			E = (S - F) * 8 / B
-			S = O / (P / Q)
-				E :	nand-ecc-strength.
-				S :	spare size per sector.
-				F :	FDM size, should be in the range [1,8].
-					It is used to store free oob data.
-				O :	oob size.
-				P :	page size.
-				Q :	nand-ecc-step-size.
-				B :	number of parity bits needed to correct
-					1 bitflip.
-					According to MTK NAND controller design,
-					this number depends on max ecc step size
-					that MTK NAND controller supports.
-					If max ecc step size supported is 1024,
-					then it should be always 14. And if max
-					ecc step size is 512, then it should be
-					always 13.
-			If the result does not match any one of the listed
-			choices above, please select the smaller valid value from
-			the list.
-			(otherwise the driver will do the adjustment at runtime)
-- pinctrl-names:	Default NAND pin GPIO setting name.
-- pinctrl-0:		GPIO setting node.
-
-Example:
-	&pio {
-		nand_pins_default: nanddefault {
-			pins_dat {
-				pinmux = <MT2701_PIN_111_MSDC0_DAT7__FUNC_NLD7>,
-					 <MT2701_PIN_112_MSDC0_DAT6__FUNC_NLD6>,
-					 <MT2701_PIN_114_MSDC0_DAT4__FUNC_NLD4>,
-					 <MT2701_PIN_118_MSDC0_DAT3__FUNC_NLD3>,
-					 <MT2701_PIN_121_MSDC0_DAT0__FUNC_NLD0>,
-					 <MT2701_PIN_120_MSDC0_DAT1__FUNC_NLD1>,
-					 <MT2701_PIN_113_MSDC0_DAT5__FUNC_NLD5>,
-					 <MT2701_PIN_115_MSDC0_RSTB__FUNC_NLD8>,
-					 <MT2701_PIN_119_MSDC0_DAT2__FUNC_NLD2>;
-				input-enable;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-up;
-			};
-
-			pins_we {
-				pinmux = <MT2701_PIN_117_MSDC0_CLK__FUNC_NWEB>;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
-			};
-
-			pins_ale {
-				pinmux = <MT2701_PIN_116_MSDC0_CMD__FUNC_NALE>;
-				drive-strength = <MTK_DRIVE_8mA>;
-				bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
-			};
-		};
-	};
-
-	&nandc {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&nand_pins_default>;
-		nand@0 {
-			reg = <0>;
-			nand-on-flash-bbt;
-			nand-ecc-mode = "hw";
-			nand-ecc-strength = <24>;
-			nand-ecc-step-size = <1024>;
-		};
-	};
-
-NAND chip optional subnodes:
-- Partitions, see Documentation/devicetree/bindings/mtd/mtd.yaml
-
-Example:
-	nand@0 {
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			preloader@0 {
-				label = "pl";
-				read-only;
-				reg = <0x00000000 0x00400000>;
-			};
-			android@00400000 {
-				label = "android";
-				reg = <0x00400000 0x12c00000>;
-			};
-		};
-	};
-
-2) ECC Engine:
-==============
-
-Required BCH properties:
-- compatible:	Should be one of
-		"mediatek,mt2701-ecc",
-		"mediatek,mt2712-ecc",
-		"mediatek,mt7622-ecc".
-- reg:		Base physical address and size of ECC.
-- interrupts:	Interrupts of ECC.
-- clocks:	ECC required clocks.
-- clock-names:	ECC clocks internal name.
-
-Example:
-
-	bch: ecc@1100e000 {
-		compatible = "mediatek,mt2701-ecc";
-		reg = <0 0x1100e000 0 0x1000>;
-		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&pericfg CLK_PERI_NFI_ECC>;
-		clock-names = "nfiecc_clk";
-	};
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 7/9] dt-bindings: mtd: Split ECC engine with rawnand controller

[Krzysztof Kozlowski]

On 09/12/2022 07:43, Xiangsheng Hou wrote:
> Split MediaTek ECC engine with rawnand controller and convert to
> YAML schema.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v4 7/9] dt-bindings: mtd: Split ECC engine with rawnand controller

[Krzysztof Kozlowski]

On 09/12/2022 07:43, Xiangsheng Hou wrote:
> Split MediaTek ECC engine with rawnand controller and convert to
> YAML schema.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 7/9] dt-bindings: mtd: Split ECC engine with rawnand controller

[Krzysztof Kozlowski]

On 09/12/2022 07:43, Xiangsheng Hou wrote:
> Split MediaTek ECC engine with rawnand controller and convert to
> YAML schema.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[Xiangsheng Hou]

Change the existing node name in order to match NAND controller DT
bindings.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 arch/arm/boot/dts/mt2701.dtsi             | 2 +-
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
 arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index b8eba3ba153c..049ed797766b 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -360,7 +360,7 @@ thermal: thermal@1100b000 {
 		mediatek,apmixedsys = <&apmixedsys>;
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt2701-nfc";
 		reg = <0 0x1100d000 0 0x1000>;
 		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index 92212cddd37e..cfbec2a2ed9d 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -560,7 +560,7 @@ spi0: spi@1100a000 {
 		status = "disabled";
 	};
 
-	nandc: nfi@1100e000 {
+	nandc: nand-controller@1100e000 {
 		compatible = "mediatek,mt2712-nfc";
 		reg = <0 0x1100e000 0 0x1000>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index 146e18b5b1f4..d98aa4936092 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -539,7 +539,7 @@ bluetooth {
 		};
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt7622-nfc";
 		reg = <0 0x1100D000 0 0x1000>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
-- 
2.25.1

[PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[Xiangsheng Hou]

Change the existing node name in order to match NAND controller DT
bindings.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 arch/arm/boot/dts/mt2701.dtsi             | 2 +-
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
 arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index b8eba3ba153c..049ed797766b 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -360,7 +360,7 @@ thermal: thermal@1100b000 {
 		mediatek,apmixedsys = <&apmixedsys>;
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt2701-nfc";
 		reg = <0 0x1100d000 0 0x1000>;
 		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index 92212cddd37e..cfbec2a2ed9d 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -560,7 +560,7 @@ spi0: spi@1100a000 {
 		status = "disabled";
 	};
 
-	nandc: nfi@1100e000 {
+	nandc: nand-controller@1100e000 {
 		compatible = "mediatek,mt2712-nfc";
 		reg = <0 0x1100e000 0 0x1000>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index 146e18b5b1f4..d98aa4936092 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -539,7 +539,7 @@ bluetooth {
 		};
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt7622-nfc";
 		reg = <0 0x1100D000 0 0x1000>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[Xiangsheng Hou]

Change the existing node name in order to match NAND controller DT
bindings.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
---
 arch/arm/boot/dts/mt2701.dtsi             | 2 +-
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
 arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index b8eba3ba153c..049ed797766b 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -360,7 +360,7 @@ thermal: thermal@1100b000 {
 		mediatek,apmixedsys = <&apmixedsys>;
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt2701-nfc";
 		reg = <0 0x1100d000 0 0x1000>;
 		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index 92212cddd37e..cfbec2a2ed9d 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -560,7 +560,7 @@ spi0: spi@1100a000 {
 		status = "disabled";
 	};
 
-	nandc: nfi@1100e000 {
+	nandc: nand-controller@1100e000 {
 		compatible = "mediatek,mt2712-nfc";
 		reg = <0 0x1100e000 0 0x1000>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index 146e18b5b1f4..d98aa4936092 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -539,7 +539,7 @@ bluetooth {
 		};
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt7622-nfc";
 		reg = <0 0x1100D000 0 0x1000>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Change the existing node name in order to match NAND controller DT
> bindings.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---
>   arch/arm/boot/dts/mt2701.dtsi             | 2 +-
>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
>   arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
>   3 files changed, 3 insertions(+), 3 deletions(-)
> 

Splitting this in two commits, one for ARM and one for ARM64 would probably
be better, but since I don't have strong opinions on that...

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Change the existing node name in order to match NAND controller DT
> bindings.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---
>   arch/arm/boot/dts/mt2701.dtsi             | 2 +-
>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
>   arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
>   3 files changed, 3 insertions(+), 3 deletions(-)
> 

Splitting this in two commits, one for ARM and one for ARM64 would probably
be better, but since I don't have strong opinions on that...

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[AngeloGioacchino Del Regno]

Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
> Change the existing node name in order to match NAND controller DT
> bindings.
> 
> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
> ---
>   arch/arm/boot/dts/mt2701.dtsi             | 2 +-
>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
>   arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
>   3 files changed, 3 insertions(+), 3 deletions(-)
> 

Splitting this in two commits, one for ARM and one for ARM64 would probably
be better, but since I don't have strong opinions on that...

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[Matthias Brugger]

On 13/12/2022 10:42, AngeloGioacchino Del Regno wrote:
> Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
>> Change the existing node name in order to match NAND controller DT
>> bindings.
>>
>> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
>> ---
>>   arch/arm/boot/dts/mt2701.dtsi             | 2 +-
>>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
>>   arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
>>   3 files changed, 3 insertions(+), 3 deletions(-)
>>
> 
> Splitting this in two commits, one for ARM and one for ARM64 would probably
> be better, but since I don't have strong opinions on that...

Yes please split this up.

Thanks!

> 
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> 
> 

Re: [PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[Matthias Brugger]

On 13/12/2022 10:42, AngeloGioacchino Del Regno wrote:
> Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
>> Change the existing node name in order to match NAND controller DT
>> bindings.
>>
>> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
>> ---
>>   arch/arm/boot/dts/mt2701.dtsi             | 2 +-
>>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
>>   arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
>>   3 files changed, 3 insertions(+), 3 deletions(-)
>>
> 
> Splitting this in two commits, one for ARM and one for ARM64 would probably
> be better, but since I don't have strong opinions on that...

Yes please split this up.

Thanks!

> 
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> 
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v4 8/9] arm/arm64: dts: mediatek: Fix existing NAND controller node name

[Matthias Brugger]

On 13/12/2022 10:42, AngeloGioacchino Del Regno wrote:
> Il 09/12/22 07:43, Xiangsheng Hou ha scritto:
>> Change the existing node name in order to match NAND controller DT
>> bindings.
>>
>> Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
>> ---
>>   arch/arm/boot/dts/mt2701.dtsi             | 2 +-
>>   arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 2 +-
>>   arch/arm64/boot/dts/mediatek/mt7622.dtsi  | 2 +-
>>   3 files changed, 3 insertions(+), 3 deletions(-)
>>
> 
> Splitting this in two commits, one for ARM and one for ARM64 would probably
> be better, but since I don't have strong opinions on that...

Yes please split this up.

Thanks!

> 
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> 
> 

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH v4 9/9] dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986

[Xiangsheng Hou]

Add dt-bindings documentation of ECC for MediaTek MT7986 SoC
platform.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
index b13d801eda76..505baf1e8830 100644
--- a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
+++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
@@ -18,6 +18,7 @@ properties:
       - mediatek,mt2701-ecc
       - mediatek,mt2712-ecc
       - mediatek,mt7622-ecc
+      - mediatek,mt7986-ecc
 
   reg:
     items:
-- 
2.25.1

[PATCH v4 9/9] dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986

[Xiangsheng Hou]

Add dt-bindings documentation of ECC for MediaTek MT7986 SoC
platform.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
index b13d801eda76..505baf1e8830 100644
--- a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
+++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
@@ -18,6 +18,7 @@ properties:
       - mediatek,mt2701-ecc
       - mediatek,mt2712-ecc
       - mediatek,mt7622-ecc
+      - mediatek,mt7986-ecc
 
   reg:
     items:
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 9/9] dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986

[Xiangsheng Hou]

Add dt-bindings documentation of ECC for MediaTek MT7986 SoC
platform.

Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
index b13d801eda76..505baf1e8830 100644
--- a/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
+++ b/Documentation/devicetree/bindings/mtd/mediatek,nand-ecc-engine.yaml
@@ -18,6 +18,7 @@ properties:
       - mediatek,mt2701-ecc
       - mediatek,mt2712-ecc
       - mediatek,mt7622-ecc
+      - mediatek,mt7986-ecc
 
   reg:
     items:
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/