[PATCH v4 0/3] Reliability improvements for Microchip MPF FPGA manager

[PATCH v4 0/3] Reliability improvements for Microchip MPF FPGA manager

[Ivan Bornyakov]

A couple of reliability improvements for Microchip Polarfire FPGA
manager:
 * move SPI I/O buffers out of stack
 * rewrite status polling routine in a time measurable way

Also improve mpf_ops_write() code readability by separating single data
frame writing routine.

ChangeLog:
  v1:
[https://lore.kernel.org/linux-fpga/20221223123854.8023-1-i.bornyakov@metrotek.ru/]
  v2:
    * split into 3 distinct patches
[https://lore.kernel.org/linux-fpga/20221226142326.8111-1-i.bornyakov@metrotek.ru/]
  v3:
    * fix polling stop condition in mpf_poll_status() as Ilpo suggested.
[https://lore.kernel.org/linux-fpga/20221227100450.2257-1-i.bornyakov@metrotek.ru/]
  v4:
    * more verbose comment for mpf_poll_status()

Ivan Bornyakov (3):
  fpga: microchip-spi: move SPI I/O buffers out of stack
  fpga: microchip-spi: rewrite status polling in a time measurable way
  fpga: microchip-spi: separate data frame write routine

 drivers/fpga/microchip-spi.c | 145 +++++++++++++++++++----------------
 1 file changed, 79 insertions(+), 66 deletions(-)

-- 
2.39.0

[PATCH v4 1/3] fpga: microchip-spi: move SPI I/O buffers out of stack

[Ivan Bornyakov]

As spi-summary doc says:
 > I/O buffers use the usual Linux rules, and must be DMA-safe.
 > You'd normally allocate them from the heap or free page pool.
 > Don't use the stack, or anything that's declared "static".

Replace spi_write() with spi_write_then_read(), which is dma-safe for
on-stack buffers. Use allocated buffers for transfers used in
spi_sync_transfer().

Although everything works OK with stack-located I/O buffers, better
follow the doc to be safe.

Fixes: 5f8d4a900830 ("fpga: microchip-spi: add Microchip MPF FPGA manager")
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 drivers/fpga/microchip-spi.c | 93 ++++++++++++++++++------------------
 1 file changed, 47 insertions(+), 46 deletions(-)

diff --git a/drivers/fpga/microchip-spi.c b/drivers/fpga/microchip-spi.c
index 7436976ea904..e72fedd93a27 100644
--- a/drivers/fpga/microchip-spi.c
+++ b/drivers/fpga/microchip-spi.c
@@ -42,46 +42,55 @@
 struct mpf_priv {
 	struct spi_device *spi;
 	bool program_mode;
+	u8 tx __aligned(ARCH_KMALLOC_MINALIGN);
+	u8 rx __aligned(ARCH_KMALLOC_MINALIGN);
 };
 
-static int mpf_read_status(struct spi_device *spi)
+static int mpf_read_status(struct mpf_priv *priv)
 {
-	u8 status = 0, status_command = MPF_SPI_READ_STATUS;
-	struct spi_transfer xfers[2] = { 0 };
-	int ret;
-
 	/*
 	 * HW status is returned on MISO in the first byte after CS went
 	 * active. However, first reading can be inadequate, so we submit
 	 * two identical SPI transfers and use result of the later one.
 	 */
-	xfers[0].tx_buf = &status_command;
-	xfers[1].tx_buf = &status_command;
-	xfers[0].rx_buf = &status;
-	xfers[1].rx_buf = &status;
-	xfers[0].len = 1;
-	xfers[1].len = 1;
-	xfers[0].cs_change = 1;
+	struct spi_transfer xfers[2] = {
+		{
+			.tx_buf = &priv->tx,
+			.rx_buf = &priv->rx,
+			.len = 1,
+			.cs_change = 1,
+		}, {
+			.tx_buf = &priv->tx,
+			.rx_buf = &priv->rx,
+			.len = 1,
+		},
+	};
+	u8 status;
+	int ret;
+
+	priv->tx = MPF_SPI_READ_STATUS;
+
+	ret = spi_sync_transfer(priv->spi, xfers, 2);
+	if (ret)
+		return ret;
 
-	ret = spi_sync_transfer(spi, xfers, 2);
+	status = priv->rx;
 
 	if ((status & MPF_STATUS_SPI_VIOLATION) ||
 	    (status & MPF_STATUS_SPI_ERROR))
-		ret = -EIO;
+		return -EIO;
 
-	return ret ? : status;
+	return status;
 }
 
 static enum fpga_mgr_states mpf_ops_state(struct fpga_manager *mgr)
 {
 	struct mpf_priv *priv = mgr->priv;
-	struct spi_device *spi;
 	bool program_mode;
 	int status;
 
-	spi = priv->spi;
 	program_mode = priv->program_mode;
-	status = mpf_read_status(spi);
+	status = mpf_read_status(priv);
 
 	if (!program_mode && !status)
 		return FPGA_MGR_STATE_OPERATING;
@@ -186,12 +195,12 @@ static int mpf_ops_parse_header(struct fpga_manager *mgr,
 }
 
 /* Poll HW status until busy bit is cleared and mask bits are set. */
-static int mpf_poll_status(struct spi_device *spi, u8 mask)
+static int mpf_poll_status(struct mpf_priv *priv, u8 mask)
 {
 	int status, retries = MPF_STATUS_POLL_RETRIES;
 
 	while (retries--) {
-		status = mpf_read_status(spi);
+		status = mpf_read_status(priv);
 		if (status < 0)
 			return status;
 
@@ -205,32 +214,32 @@ static int mpf_poll_status(struct spi_device *spi, u8 mask)
 	return -EBUSY;
 }
 
-static int mpf_spi_write(struct spi_device *spi, const void *buf, size_t buf_size)
+static int mpf_spi_write(struct mpf_priv *priv, const void *buf, size_t buf_size)
 {
-	int status = mpf_poll_status(spi, 0);
+	int status = mpf_poll_status(priv, 0);
 
 	if (status < 0)
 		return status;
 
-	return spi_write(spi, buf, buf_size);
+	return spi_write_then_read(priv->spi, buf, buf_size, NULL, 0);
 }
 
-static int mpf_spi_write_then_read(struct spi_device *spi,
+static int mpf_spi_write_then_read(struct mpf_priv *priv,
 				   const void *txbuf, size_t txbuf_size,
 				   void *rxbuf, size_t rxbuf_size)
 {
 	const u8 read_command[] = { MPF_SPI_READ_DATA };
 	int ret;
 
-	ret = mpf_spi_write(spi, txbuf, txbuf_size);
+	ret = mpf_spi_write(priv, txbuf, txbuf_size);
 	if (ret)
 		return ret;
 
-	ret = mpf_poll_status(spi, MPF_STATUS_READY);
+	ret = mpf_poll_status(priv, MPF_STATUS_READY);
 	if (ret < 0)
 		return ret;
 
-	return spi_write_then_read(spi, read_command, sizeof(read_command),
+	return spi_write_then_read(priv->spi, read_command, sizeof(read_command),
 				   rxbuf, rxbuf_size);
 }
 
@@ -242,7 +251,6 @@ static int mpf_ops_write_init(struct fpga_manager *mgr,
 	const u8 isc_en_command[] = { MPF_SPI_ISC_ENABLE };
 	struct mpf_priv *priv = mgr->priv;
 	struct device *dev = &mgr->dev;
-	struct spi_device *spi;
 	u32 isc_ret = 0;
 	int ret;
 
@@ -251,9 +259,7 @@ static int mpf_ops_write_init(struct fpga_manager *mgr,
 		return -EOPNOTSUPP;
 	}
 
-	spi = priv->spi;
-
-	ret = mpf_spi_write_then_read(spi, isc_en_command, sizeof(isc_en_command),
+	ret = mpf_spi_write_then_read(priv, isc_en_command, sizeof(isc_en_command),
 				      &isc_ret, sizeof(isc_ret));
 	if (ret || isc_ret) {
 		dev_err(dev, "Failed to enable ISC: spi_ret %d, isc_ret %u\n",
@@ -261,7 +267,7 @@ static int mpf_ops_write_init(struct fpga_manager *mgr,
 		return -EFAULT;
 	}
 
-	ret = mpf_spi_write(spi, program_mode, sizeof(program_mode));
+	ret = mpf_spi_write(priv, program_mode, sizeof(program_mode));
 	if (ret) {
 		dev_err(dev, "Failed to enter program mode: %d\n", ret);
 		return ret;
@@ -274,11 +280,9 @@ static int mpf_ops_write_init(struct fpga_manager *mgr,
 
 static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count)
 {
-	u8 spi_frame_command[] = { MPF_SPI_FRAME };
 	struct spi_transfer xfers[2] = { 0 };
 	struct mpf_priv *priv = mgr->priv;
 	struct device *dev = &mgr->dev;
-	struct spi_device *spi;
 	int ret, i;
 
 	if (count % MPF_SPI_FRAME_SIZE) {
@@ -287,18 +291,18 @@ static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count
 		return -EINVAL;
 	}
 
-	spi = priv->spi;
-
-	xfers[0].tx_buf = spi_frame_command;
-	xfers[0].len = sizeof(spi_frame_command);
+	xfers[0].tx_buf = &priv->tx;
+	xfers[0].len = 1;
 
 	for (i = 0; i < count / MPF_SPI_FRAME_SIZE; i++) {
 		xfers[1].tx_buf = buf + i * MPF_SPI_FRAME_SIZE;
 		xfers[1].len = MPF_SPI_FRAME_SIZE;
 
-		ret = mpf_poll_status(spi, 0);
-		if (ret >= 0)
-			ret = spi_sync_transfer(spi, xfers, ARRAY_SIZE(xfers));
+		ret = mpf_poll_status(priv, 0);
+		if (ret >= 0) {
+			priv->tx = MPF_SPI_FRAME;
+			ret = spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers));
+		}
 
 		if (ret) {
 			dev_err(dev, "Failed to write bitstream frame %d/%zu\n",
@@ -317,12 +321,9 @@ static int mpf_ops_write_complete(struct fpga_manager *mgr,
 	const u8 release_command[] = { MPF_SPI_RELEASE };
 	struct mpf_priv *priv = mgr->priv;
 	struct device *dev = &mgr->dev;
-	struct spi_device *spi;
 	int ret;
 
-	spi = priv->spi;
-
-	ret = mpf_spi_write(spi, isc_dis_command, sizeof(isc_dis_command));
+	ret = mpf_spi_write(priv, isc_dis_command, sizeof(isc_dis_command));
 	if (ret) {
 		dev_err(dev, "Failed to disable ISC: %d\n", ret);
 		return ret;
@@ -330,7 +331,7 @@ static int mpf_ops_write_complete(struct fpga_manager *mgr,
 
 	usleep_range(1000, 2000);
 
-	ret = mpf_spi_write(spi, release_command, sizeof(release_command));
+	ret = mpf_spi_write(priv, release_command, sizeof(release_command));
 	if (ret) {
 		dev_err(dev, "Failed to exit program mode: %d\n", ret);
 		return ret;
-- 
2.39.0

Re: [PATCH v4 1/3] fpga: microchip-spi: move SPI I/O buffers out of stack

[Xu Yilun]

On 2022-12-29 at 13:46:02 +0300, Ivan Bornyakov wrote:
> As spi-summary doc says:
>  > I/O buffers use the usual Linux rules, and must be DMA-safe.
>  > You'd normally allocate them from the heap or free page pool.
>  > Don't use the stack, or anything that's declared "static".
> 
> Replace spi_write() with spi_write_then_read(), which is dma-safe for
> on-stack buffers. Use allocated buffers for transfers used in

How about "Use cacheline aligned buffers for ..."

> spi_sync_transfer().
> 
> Although everything works OK with stack-located I/O buffers, better
> follow the doc to be safe.
> 
> Fixes: 5f8d4a900830 ("fpga: microchip-spi: add Microchip MPF FPGA manager")
> Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> ---
>  drivers/fpga/microchip-spi.c | 93 ++++++++++++++++++------------------
>  1 file changed, 47 insertions(+), 46 deletions(-)
> 
> diff --git a/drivers/fpga/microchip-spi.c b/drivers/fpga/microchip-spi.c
> index 7436976ea904..e72fedd93a27 100644
> --- a/drivers/fpga/microchip-spi.c
> +++ b/drivers/fpga/microchip-spi.c
> @@ -42,46 +42,55 @@
>  struct mpf_priv {
>  	struct spi_device *spi;
>  	bool program_mode;
> +	u8 tx __aligned(ARCH_KMALLOC_MINALIGN);
> +	u8 rx __aligned(ARCH_KMALLOC_MINALIGN);

If the 2 buffers are used synchronously by dma, they could share a
cacheline. Just separate them from other members should be OK, like:

	u8 tx __aligned(ARCH_KMALLOC_MINALIGN);
	u8 rx;

>  };
>  

[PATCH v4 2/3] fpga: microchip-spi: rewrite status polling in a time measurable way

[Ivan Bornyakov]

Original busy loop with retries count in mpf_poll_status() is not too
reliable, as it takes different times on different systems. Replace it
with read_poll_timeout() macro.

While at it, fix polling stop condition to met function's original
intention declared in the comment. The issue with original polling stop
condition is that it stops if any of mask bits is set, while intention
was to stop if all mask bits is set. This was not noticible because only
MPF_STATUS_READY is passed as mask argument and it is BIT(1).

Fixes: 5f8d4a900830 ("fpga: microchip-spi: add Microchip MPF FPGA manager")
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 drivers/fpga/microchip-spi.c | 32 +++++++++++++++++---------------
 1 file changed, 17 insertions(+), 15 deletions(-)

diff --git a/drivers/fpga/microchip-spi.c b/drivers/fpga/microchip-spi.c
index e72fedd93a27..995b1964e0fe 100644
--- a/drivers/fpga/microchip-spi.c
+++ b/drivers/fpga/microchip-spi.c
@@ -6,6 +6,7 @@
 #include <asm/unaligned.h>
 #include <linux/delay.h>
 #include <linux/fpga/fpga-mgr.h>
+#include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/spi/spi.h>
@@ -33,7 +34,7 @@
 
 #define	MPF_BITS_PER_COMPONENT_SIZE	22
 
-#define	MPF_STATUS_POLL_RETRIES		10000
+#define	MPF_STATUS_POLL_TIMEOUT		(2 * USEC_PER_SEC)
 #define	MPF_STATUS_BUSY			BIT(0)
 #define	MPF_STATUS_READY		BIT(1)
 #define	MPF_STATUS_SPI_VIOLATION	BIT(2)
@@ -194,24 +195,25 @@ static int mpf_ops_parse_header(struct fpga_manager *mgr,
 	return 0;
 }
 
-/* Poll HW status until busy bit is cleared and mask bits are set. */
 static int mpf_poll_status(struct mpf_priv *priv, u8 mask)
 {
-	int status, retries = MPF_STATUS_POLL_RETRIES;
+	int ret, status;
 
-	while (retries--) {
-		status = mpf_read_status(priv);
-		if (status < 0)
-			return status;
-
-		if (status & MPF_STATUS_BUSY)
-			continue;
-
-		if (!mask || (status & mask))
-			return status;
-	}
+	/*
+	 * Busy poll HW status. Polling stops if any of the following
+	 * conditions are met:
+	 *  - timeout is reached
+	 *  - mpf_read_status() returns an error
+	 *  - busy bit is cleared AND mask bits are set
+	 */
+	ret = read_poll_timeout(mpf_read_status, status,
+				(status < 0) ||
+				((status & (MPF_STATUS_BUSY | mask)) == mask),
+				0, MPF_STATUS_POLL_TIMEOUT, false, priv);
+	if (ret < 0)
+		return ret;
 
-	return -EBUSY;
+	return status;
 }
 
 static int mpf_spi_write(struct mpf_priv *priv, const void *buf, size_t buf_size)
-- 
2.39.0

Re: [PATCH v4 2/3] fpga: microchip-spi: rewrite status polling in a time measurable way

[Xu Yilun]

On 2022-12-29 at 13:46:03 +0300, Ivan Bornyakov wrote:
> Original busy loop with retries count in mpf_poll_status() is not too
> reliable, as it takes different times on different systems. Replace it
> with read_poll_timeout() macro.
> 
> While at it, fix polling stop condition to met function's original
> intention declared in the comment. The issue with original polling stop
> condition is that it stops if any of mask bits is set, while intention
> was to stop if all mask bits is set. This was not noticible because only
> MPF_STATUS_READY is passed as mask argument and it is BIT(1).
> 
> Fixes: 5f8d4a900830 ("fpga: microchip-spi: add Microchip MPF FPGA manager")
> Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>

Acked-by: Xu Yilun <yilun.xu@intel.com>

> ---
>  drivers/fpga/microchip-spi.c | 32 +++++++++++++++++---------------
>  1 file changed, 17 insertions(+), 15 deletions(-)
> 
> diff --git a/drivers/fpga/microchip-spi.c b/drivers/fpga/microchip-spi.c
> index e72fedd93a27..995b1964e0fe 100644
> --- a/drivers/fpga/microchip-spi.c
> +++ b/drivers/fpga/microchip-spi.c
> @@ -6,6 +6,7 @@
>  #include <asm/unaligned.h>
>  #include <linux/delay.h>
>  #include <linux/fpga/fpga-mgr.h>
> +#include <linux/iopoll.h>
>  #include <linux/module.h>
>  #include <linux/of_device.h>
>  #include <linux/spi/spi.h>
> @@ -33,7 +34,7 @@
>  
>  #define	MPF_BITS_PER_COMPONENT_SIZE	22
>  
> -#define	MPF_STATUS_POLL_RETRIES		10000
> +#define	MPF_STATUS_POLL_TIMEOUT		(2 * USEC_PER_SEC)
>  #define	MPF_STATUS_BUSY			BIT(0)
>  #define	MPF_STATUS_READY		BIT(1)
>  #define	MPF_STATUS_SPI_VIOLATION	BIT(2)
> @@ -194,24 +195,25 @@ static int mpf_ops_parse_header(struct fpga_manager *mgr,
>  	return 0;
>  }
>  
> -/* Poll HW status until busy bit is cleared and mask bits are set. */
>  static int mpf_poll_status(struct mpf_priv *priv, u8 mask)
>  {
> -	int status, retries = MPF_STATUS_POLL_RETRIES;
> +	int ret, status;
>  
> -	while (retries--) {
> -		status = mpf_read_status(priv);
> -		if (status < 0)
> -			return status;
> -
> -		if (status & MPF_STATUS_BUSY)
> -			continue;
> -
> -		if (!mask || (status & mask))
> -			return status;
> -	}
> +	/*
> +	 * Busy poll HW status. Polling stops if any of the following
> +	 * conditions are met:
> +	 *  - timeout is reached
> +	 *  - mpf_read_status() returns an error
> +	 *  - busy bit is cleared AND mask bits are set
> +	 */
> +	ret = read_poll_timeout(mpf_read_status, status,
> +				(status < 0) ||
> +				((status & (MPF_STATUS_BUSY | mask)) == mask),
> +				0, MPF_STATUS_POLL_TIMEOUT, false, priv);
> +	if (ret < 0)
> +		return ret;
>  
> -	return -EBUSY;
> +	return status;
>  }
>  
>  static int mpf_spi_write(struct mpf_priv *priv, const void *buf, size_t buf_size)
> -- 
> 2.39.0
> 
> 

[PATCH v4 3/3] fpga: microchip-spi: separate data frame write routine

[Ivan Bornyakov]

mpf_ops_write() function writes bitstream data to the FPGA by a smaller
frames. Introduce mpf_spi_frame_write() function which is for writing a
single data frame and use it in mpf_ops_write().

No functional changes intended.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 drivers/fpga/microchip-spi.c | 36 +++++++++++++++++++++++-------------
 1 file changed, 23 insertions(+), 13 deletions(-)

diff --git a/drivers/fpga/microchip-spi.c b/drivers/fpga/microchip-spi.c
index 995b1964e0fe..8a541986f6f2 100644
--- a/drivers/fpga/microchip-spi.c
+++ b/drivers/fpga/microchip-spi.c
@@ -280,9 +280,30 @@ static int mpf_ops_write_init(struct fpga_manager *mgr,
 	return 0;
 }
 
+static int mpf_spi_frame_write(struct mpf_priv *priv, const char *buf)
+{
+	struct spi_transfer xfers[2] = {
+		{
+			.tx_buf = &priv->tx,
+			.len = 1,
+		}, {
+			.tx_buf = buf,
+			.len = MPF_SPI_FRAME_SIZE,
+		},
+	};
+	int ret;
+
+	ret = mpf_poll_status(priv, 0);
+	if (ret < 0)
+		return ret;
+
+	priv->tx = MPF_SPI_FRAME;
+
+	return spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers));
+}
+
 static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count)
 {
-	struct spi_transfer xfers[2] = { 0 };
 	struct mpf_priv *priv = mgr->priv;
 	struct device *dev = &mgr->dev;
 	int ret, i;
@@ -293,19 +314,8 @@ static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count
 		return -EINVAL;
 	}
 
-	xfers[0].tx_buf = &priv->tx;
-	xfers[0].len = 1;
-
 	for (i = 0; i < count / MPF_SPI_FRAME_SIZE; i++) {
-		xfers[1].tx_buf = buf + i * MPF_SPI_FRAME_SIZE;
-		xfers[1].len = MPF_SPI_FRAME_SIZE;
-
-		ret = mpf_poll_status(priv, 0);
-		if (ret >= 0) {
-			priv->tx = MPF_SPI_FRAME;
-			ret = spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers));
-		}
-
+		ret = mpf_spi_frame_write(priv, buf + i * MPF_SPI_FRAME_SIZE);
 		if (ret) {
 			dev_err(dev, "Failed to write bitstream frame %d/%zu\n",
 				i, count / MPF_SPI_FRAME_SIZE);
-- 
2.39.0

Re: [PATCH v4 3/3] fpga: microchip-spi: separate data frame write routine

[Xu Yilun]

On 2022-12-29 at 13:46:04 +0300, Ivan Bornyakov wrote:
> mpf_ops_write() function writes bitstream data to the FPGA by a smaller
> frames. Introduce mpf_spi_frame_write() function which is for writing a
> single data frame and use it in mpf_ops_write().
> 
> No functional changes intended.
> 
> Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>

Acked-by: Xu Yilun <yilun.xu@intel.com>

> ---
>  drivers/fpga/microchip-spi.c | 36 +++++++++++++++++++++++-------------
>  1 file changed, 23 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/fpga/microchip-spi.c b/drivers/fpga/microchip-spi.c
> index 995b1964e0fe..8a541986f6f2 100644
> --- a/drivers/fpga/microchip-spi.c
> +++ b/drivers/fpga/microchip-spi.c
> @@ -280,9 +280,30 @@ static int mpf_ops_write_init(struct fpga_manager *mgr,
>  	return 0;
>  }
>  
> +static int mpf_spi_frame_write(struct mpf_priv *priv, const char *buf)
> +{
> +	struct spi_transfer xfers[2] = {
> +		{
> +			.tx_buf = &priv->tx,
> +			.len = 1,
> +		}, {
> +			.tx_buf = buf,
> +			.len = MPF_SPI_FRAME_SIZE,
> +		},
> +	};
> +	int ret;
> +
> +	ret = mpf_poll_status(priv, 0);
> +	if (ret < 0)
> +		return ret;
> +
> +	priv->tx = MPF_SPI_FRAME;
> +
> +	return spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers));
> +}
> +
>  static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count)
>  {
> -	struct spi_transfer xfers[2] = { 0 };
>  	struct mpf_priv *priv = mgr->priv;
>  	struct device *dev = &mgr->dev;
>  	int ret, i;
> @@ -293,19 +314,8 @@ static int mpf_ops_write(struct fpga_manager *mgr, const char *buf, size_t count
>  		return -EINVAL;
>  	}
>  
> -	xfers[0].tx_buf = &priv->tx;
> -	xfers[0].len = 1;
> -
>  	for (i = 0; i < count / MPF_SPI_FRAME_SIZE; i++) {
> -		xfers[1].tx_buf = buf + i * MPF_SPI_FRAME_SIZE;
> -		xfers[1].len = MPF_SPI_FRAME_SIZE;
> -
> -		ret = mpf_poll_status(priv, 0);
> -		if (ret >= 0) {
> -			priv->tx = MPF_SPI_FRAME;
> -			ret = spi_sync_transfer(priv->spi, xfers, ARRAY_SIZE(xfers));
> -		}
> -
> +		ret = mpf_spi_frame_write(priv, buf + i * MPF_SPI_FRAME_SIZE);
>  		if (ret) {
>  			dev_err(dev, "Failed to write bitstream frame %d/%zu\n",
>  				i, count / MPF_SPI_FRAME_SIZE);
> -- 
> 2.39.0
> 
>