[PATCH v8 0/5] Add BananaPi R3

[PATCH v8 0/5] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on linux 6.2-rc1 and i dropped already applied
Patches from v7.

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined. These errors also came up for mt7986a-rfb.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137

changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- rebase on next so dropped already applied patches
- squashed overlay-patch into the bpi-r3 base support
- moved regulators from mmc-dts to common dtsi
- changed dtsi to dts (as board base dtb) and mmc-dts to overlays
- renamed overlays to dtso
- removed angelos RB because of changes in bpi-r3 patch

v6:
- dropped regulators from usb-patch as suggested by chunfeng yun
- moved 3v3 regulator to mmc-patch as it is needed for emmc to work
  rfbs were tested by sam shih, r3 by me
- dropped RB from AngeloGioacchino from mmc-patch due to this change
- fixed links in coverletter which were broken in v5
- i hope this series is sent without errors now (my mailprovider limited
  mails last 2 times while sending part 10)

v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes

v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches

v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays

Frank Wunderlich (2):
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3

Sam Shih (3):
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 120 +++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 122 +++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |   8 +
 10 files changed, 882 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

-- 
2.34.1

[PATCH v8 0/5] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on linux 6.2-rc1 and i dropped already applied
Patches from v7.

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined. These errors also came up for mt7986a-rfb.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137

changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- rebase on next so dropped already applied patches
- squashed overlay-patch into the bpi-r3 base support
- moved regulators from mmc-dts to common dtsi
- changed dtsi to dts (as board base dtb) and mmc-dts to overlays
- renamed overlays to dtso
- removed angelos RB because of changes in bpi-r3 patch

v6:
- dropped regulators from usb-patch as suggested by chunfeng yun
- moved 3v3 regulator to mmc-patch as it is needed for emmc to work
  rfbs were tested by sam shih, r3 by me
- dropped RB from AngeloGioacchino from mmc-patch due to this change
- fixed links in coverletter which were broken in v5
- i hope this series is sent without errors now (my mailprovider limited
  mails last 2 times while sending part 10)

v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes

v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches

v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays

Frank Wunderlich (2):
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3

Sam Shih (3):
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 120 +++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 122 +++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |   8 +
 10 files changed, 882 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

-- 
2.34.1

[PATCH v8 0/5] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on linux 6.2-rc1 and i dropped already applied
Patches from v7.

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined. These errors also came up for mt7986a-rfb.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137

changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- rebase on next so dropped already applied patches
- squashed overlay-patch into the bpi-r3 base support
- moved regulators from mmc-dts to common dtsi
- changed dtsi to dts (as board base dtb) and mmc-dts to overlays
- renamed overlays to dtso
- removed angelos RB because of changes in bpi-r3 patch

v6:
- dropped regulators from usb-patch as suggested by chunfeng yun
- moved 3v3 regulator to mmc-patch as it is needed for emmc to work
  rfbs were tested by sam shih, r3 by me
- dropped RB from AngeloGioacchino from mmc-patch due to this change
- fixed links in coverletter which were broken in v5
- i hope this series is sent without errors now (my mailprovider limited
  mails last 2 times while sending part 10)

v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes

v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches

v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays

Frank Wunderlich (2):
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3

Sam Shih (3):
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 120 +++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 122 +++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |   8 +
 10 files changed, 882 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 0/5] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on linux 6.2-rc1 and i dropped already applied
Patches from v7.

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined. These errors also came up for mt7986a-rfb.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137

changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- rebase on next so dropped already applied patches
- squashed overlay-patch into the bpi-r3 base support
- moved regulators from mmc-dts to common dtsi
- changed dtsi to dts (as board base dtb) and mmc-dts to overlays
- renamed overlays to dtso
- removed angelos RB because of changes in bpi-r3 patch

v6:
- dropped regulators from usb-patch as suggested by chunfeng yun
- moved 3v3 regulator to mmc-patch as it is needed for emmc to work
  rfbs were tested by sam shih, r3 by me
- dropped RB from AngeloGioacchino from mmc-patch due to this change
- fixed links in coverletter which were broken in v5
- i hope this series is sent without errors now (my mailprovider limited
  mails last 2 times while sending part 10)

v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes

v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches

v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays

Frank Wunderlich (2):
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3

Sam Shih (3):
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 120 +++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 122 +++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |   8 +
 10 files changed, 882 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v8 1/5] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
           - enum:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
+              - mediatek,mt7986-tphy
               - mediatek,mt8183-tphy
               - mediatek,mt8186-tphy
               - mediatek,mt8192-tphy
-- 
2.34.1

[PATCH v8 1/5] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
           - enum:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
+              - mediatek,mt7986-tphy
               - mediatek,mt8183-tphy
               - mediatek,mt8186-tphy
               - mediatek,mt8192-tphy
-- 
2.34.1

[PATCH v8 1/5] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
           - enum:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
+              - mediatek,mt7986-tphy
               - mediatek,mt8183-tphy
               - mediatek,mt8186-tphy
               - mediatek,mt8192-tphy
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 1/5] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
           - enum:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
+              - mediatek,mt7986-tphy
               - mediatek,mt8183-tphy
               - mediatek,mt8186-tphy
               - mediatek,mt8192-tphy
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v8 2/5] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds USB support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
changes compared to sams original version:
- reorder xhci-clocks based on yaml binding

v5:
 - update ranges/reg of usb-phy
 - not added RB from AngeloGioacchino for v4 because of these changes

v6:
- remove unused usb regulators
- remove 3v3 regulator (will be added with emmc-patch)
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts |  8 +++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts |  8 +++
 3 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 9b83925893b7..58089fcf4d16 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -140,6 +140,10 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +205,10 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 0e9406fc63e2..9ff2968152ae 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -323,6 +323,61 @@ spi1: spi@1100b000 {
 			status = "disabled";
 		};
 
+		ssusb: usb@11200000 {
+			compatible = "mediatek,mt7986-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x2e00>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+				 <&infracfg CLK_INFRA_IUSB_CK>,
+				 <&infracfg CLK_INFRA_IUSB_133_CK>,
+				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
+				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+			clock-names = "sys_ck",
+				      "ref_ck",
+				      "mcu_ck",
+				      "dma_ck",
+				      "xhci_ck";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		usb_phy: t-phy@11e10000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e10000 0x1700>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@1000 {
+				reg = <0x1000 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 243760cd3011..188ce82ae56c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -167,10 +167,18 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
-- 
2.34.1

[PATCH v8 2/5] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds USB support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
changes compared to sams original version:
- reorder xhci-clocks based on yaml binding

v5:
 - update ranges/reg of usb-phy
 - not added RB from AngeloGioacchino for v4 because of these changes

v6:
- remove unused usb regulators
- remove 3v3 regulator (will be added with emmc-patch)
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts |  8 +++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts |  8 +++
 3 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 9b83925893b7..58089fcf4d16 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -140,6 +140,10 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +205,10 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 0e9406fc63e2..9ff2968152ae 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -323,6 +323,61 @@ spi1: spi@1100b000 {
 			status = "disabled";
 		};
 
+		ssusb: usb@11200000 {
+			compatible = "mediatek,mt7986-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x2e00>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+				 <&infracfg CLK_INFRA_IUSB_CK>,
+				 <&infracfg CLK_INFRA_IUSB_133_CK>,
+				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
+				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+			clock-names = "sys_ck",
+				      "ref_ck",
+				      "mcu_ck",
+				      "dma_ck",
+				      "xhci_ck";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		usb_phy: t-phy@11e10000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e10000 0x1700>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@1000 {
+				reg = <0x1000 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 243760cd3011..188ce82ae56c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -167,10 +167,18 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
-- 
2.34.1

[PATCH v8 2/5] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds USB support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
changes compared to sams original version:
- reorder xhci-clocks based on yaml binding

v5:
 - update ranges/reg of usb-phy
 - not added RB from AngeloGioacchino for v4 because of these changes

v6:
- remove unused usb regulators
- remove 3v3 regulator (will be added with emmc-patch)
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts |  8 +++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts |  8 +++
 3 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 9b83925893b7..58089fcf4d16 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -140,6 +140,10 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +205,10 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 0e9406fc63e2..9ff2968152ae 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -323,6 +323,61 @@ spi1: spi@1100b000 {
 			status = "disabled";
 		};
 
+		ssusb: usb@11200000 {
+			compatible = "mediatek,mt7986-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x2e00>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+				 <&infracfg CLK_INFRA_IUSB_CK>,
+				 <&infracfg CLK_INFRA_IUSB_133_CK>,
+				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
+				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+			clock-names = "sys_ck",
+				      "ref_ck",
+				      "mcu_ck",
+				      "dma_ck",
+				      "xhci_ck";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		usb_phy: t-phy@11e10000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e10000 0x1700>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@1000 {
+				reg = <0x1000 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 243760cd3011..188ce82ae56c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -167,10 +167,18 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 2/5] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds USB support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
changes compared to sams original version:
- reorder xhci-clocks based on yaml binding

v5:
 - update ranges/reg of usb-phy
 - not added RB from AngeloGioacchino for v4 because of these changes

v6:
- remove unused usb regulators
- remove 3v3 regulator (will be added with emmc-patch)
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts |  8 +++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts |  8 +++
 3 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 9b83925893b7..58089fcf4d16 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -140,6 +140,10 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +205,10 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 0e9406fc63e2..9ff2968152ae 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -323,6 +323,61 @@ spi1: spi@1100b000 {
 			status = "disabled";
 		};
 
+		ssusb: usb@11200000 {
+			compatible = "mediatek,mt7986-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x2e00>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+				 <&infracfg CLK_INFRA_IUSB_CK>,
+				 <&infracfg CLK_INFRA_IUSB_133_CK>,
+				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
+				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+			clock-names = "sys_ck",
+				      "ref_ck",
+				      "mcu_ck",
+				      "dma_ck",
+				      "xhci_ck";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		usb_phy: t-phy@11e10000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e10000 0x1700>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@1000 {
+				reg = <0x1000 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 243760cd3011..188ce82ae56c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -167,10 +167,18 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v8 3/5] arm64: dts: mt7986: add mmc related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
v2:
- update mmc-node because clocks changed

v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v6:
- add 3v3 regulator in mt7986a-rfb (was in usb patch before)
- dropped AngeloGioacchino RB because of this change
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 96 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 +++
 2 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 58089fcf4d16..c7a2ac764a30 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -23,6 +25,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -58,7 +78,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9ff2968152ae..9c552442c02d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -346,6 +346,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

[PATCH v8 3/5] arm64: dts: mt7986: add mmc related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
v2:
- update mmc-node because clocks changed

v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v6:
- add 3v3 regulator in mt7986a-rfb (was in usb patch before)
- dropped AngeloGioacchino RB because of this change
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 96 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 +++
 2 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 58089fcf4d16..c7a2ac764a30 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -23,6 +25,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -58,7 +78,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9ff2968152ae..9c552442c02d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -346,6 +346,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

[PATCH v8 3/5] arm64: dts: mt7986: add mmc related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
v2:
- update mmc-node because clocks changed

v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v6:
- add 3v3 regulator in mt7986a-rfb (was in usb patch before)
- dropped AngeloGioacchino RB because of this change
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 96 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 +++
 2 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 58089fcf4d16..c7a2ac764a30 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -23,6 +25,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -58,7 +78,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9ff2968152ae..9c552442c02d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -346,6 +346,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 3/5] arm64: dts: mt7986: add mmc related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
v2:
- update mmc-node because clocks changed

v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v6:
- add 3v3 regulator in mt7986a-rfb (was in usb patch before)
- dropped AngeloGioacchino RB because of this change
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 96 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 +++
 2 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 58089fcf4d16..c7a2ac764a30 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -23,6 +25,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -58,7 +78,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9ff2968152ae..9c552442c02d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -346,6 +346,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v8 4/5] arm64: dts: mt7986: add pcie related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds PCIe support for MT7986.

Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
changes compared to sams original version:

- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 52 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index c7a2ac764a30..4f18b4a9a8c8 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -93,6 +93,15 @@ &mmc0 {
 	non-removable;
 	no-sd;
 	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
 	status = "okay";
 };
 
@@ -155,6 +164,13 @@ conf-rst {
 		};
 	};
 
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9c552442c02d..f6e980771b69 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/mt7986-clk.h>
 #include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	compatible = "mediatek,mt7986a";
@@ -361,6 +362,57 @@ mmc0: mmc@11230000 {
 			status = "disabled";
 		};
 
+		pcie: pcie@11280000 {
+			compatible = "mediatek,mt7986-pcie",
+				     "mediatek,mt8192-pcie";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg = <0x00 0x11280000 0x00 0x4000>;
+			reg-names = "pcie-mac";
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0x00 0x20000000 0x00
+				  0x20000000 0x00 0x10000000>;
+			clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+				 <&infracfg CLK_INFRA_IPCIE_CK>,
+				 <&infracfg CLK_INFRA_IPCIER_CK>,
+				 <&infracfg CLK_INFRA_IPCIEB_CK>;
+			clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+			status = "disabled";
+
+			phys = <&pcie_port PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &pcie_intc 0>,
+					<0 0 0 2 &pcie_intc 1>,
+					<0 0 0 3 &pcie_intc 2>,
+					<0 0 0 4 &pcie_intc 3>;
+			pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie_phy: t-phy@11c00000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			pcie_port: pcie-phy@11c00000 {
+				reg = <0 0x11c00000 0 0x20000>;
+				clocks = <&clk40m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

[PATCH v8 4/5] arm64: dts: mt7986: add pcie related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds PCIe support for MT7986.

Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
changes compared to sams original version:

- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 52 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index c7a2ac764a30..4f18b4a9a8c8 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -93,6 +93,15 @@ &mmc0 {
 	non-removable;
 	no-sd;
 	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
 	status = "okay";
 };
 
@@ -155,6 +164,13 @@ conf-rst {
 		};
 	};
 
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9c552442c02d..f6e980771b69 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/mt7986-clk.h>
 #include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	compatible = "mediatek,mt7986a";
@@ -361,6 +362,57 @@ mmc0: mmc@11230000 {
 			status = "disabled";
 		};
 
+		pcie: pcie@11280000 {
+			compatible = "mediatek,mt7986-pcie",
+				     "mediatek,mt8192-pcie";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg = <0x00 0x11280000 0x00 0x4000>;
+			reg-names = "pcie-mac";
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0x00 0x20000000 0x00
+				  0x20000000 0x00 0x10000000>;
+			clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+				 <&infracfg CLK_INFRA_IPCIE_CK>,
+				 <&infracfg CLK_INFRA_IPCIER_CK>,
+				 <&infracfg CLK_INFRA_IPCIEB_CK>;
+			clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+			status = "disabled";
+
+			phys = <&pcie_port PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &pcie_intc 0>,
+					<0 0 0 2 &pcie_intc 1>,
+					<0 0 0 3 &pcie_intc 2>,
+					<0 0 0 4 &pcie_intc 3>;
+			pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie_phy: t-phy@11c00000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			pcie_port: pcie-phy@11c00000 {
+				reg = <0 0x11c00000 0 0x20000>;
+				clocks = <&clk40m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

[PATCH v8 4/5] arm64: dts: mt7986: add pcie related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds PCIe support for MT7986.

Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
changes compared to sams original version:

- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 52 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index c7a2ac764a30..4f18b4a9a8c8 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -93,6 +93,15 @@ &mmc0 {
 	non-removable;
 	no-sd;
 	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
 	status = "okay";
 };
 
@@ -155,6 +164,13 @@ conf-rst {
 		};
 	};
 
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9c552442c02d..f6e980771b69 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/mt7986-clk.h>
 #include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	compatible = "mediatek,mt7986a";
@@ -361,6 +362,57 @@ mmc0: mmc@11230000 {
 			status = "disabled";
 		};
 
+		pcie: pcie@11280000 {
+			compatible = "mediatek,mt7986-pcie",
+				     "mediatek,mt8192-pcie";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg = <0x00 0x11280000 0x00 0x4000>;
+			reg-names = "pcie-mac";
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0x00 0x20000000 0x00
+				  0x20000000 0x00 0x10000000>;
+			clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+				 <&infracfg CLK_INFRA_IPCIE_CK>,
+				 <&infracfg CLK_INFRA_IPCIER_CK>,
+				 <&infracfg CLK_INFRA_IPCIEB_CK>;
+			clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+			status = "disabled";
+
+			phys = <&pcie_port PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &pcie_intc 0>,
+					<0 0 0 2 &pcie_intc 1>,
+					<0 0 0 3 &pcie_intc 2>,
+					<0 0 0 4 &pcie_intc 3>;
+			pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie_phy: t-phy@11c00000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			pcie_port: pcie-phy@11c00000 {
+				reg = <0 0x11c00000 0 0x20000>;
+				clocks = <&clk40m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 4/5] arm64: dts: mt7986: add pcie related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds PCIe support for MT7986.

Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
changes compared to sams original version:

- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 52 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index c7a2ac764a30..4f18b4a9a8c8 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -93,6 +93,15 @@ &mmc0 {
 	non-removable;
 	no-sd;
 	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
 	status = "okay";
 };
 
@@ -155,6 +164,13 @@ conf-rst {
 		};
 	};
 
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 9c552442c02d..f6e980771b69 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/mt7986-clk.h>
 #include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	compatible = "mediatek,mt7986a";
@@ -361,6 +362,57 @@ mmc0: mmc@11230000 {
 			status = "disabled";
 		};
 
+		pcie: pcie@11280000 {
+			compatible = "mediatek,mt7986-pcie",
+				     "mediatek,mt8192-pcie";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg = <0x00 0x11280000 0x00 0x4000>;
+			reg-names = "pcie-mac";
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0x00 0x20000000 0x00
+				  0x20000000 0x00 0x10000000>;
+			clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+				 <&infracfg CLK_INFRA_IPCIE_CK>,
+				 <&infracfg CLK_INFRA_IPCIER_CK>,
+				 <&infracfg CLK_INFRA_IPCIEB_CK>;
+			clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+			status = "disabled";
+
+			phys = <&pcie_port PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &pcie_intc 0>,
+					<0 0 0 2 &pcie_intc 1>,
+					<0 0 0 3 &pcie_intc 2>,
+					<0 0 0 4 &pcie_intc 3>;
+			pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie_phy: t-phy@11c00000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			pcie_port: pcie-phy@11c00000 {
+				reg = <0 0x11c00000 0 0x20000>;
+				clocks = <&clk40m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- SPI-NAND/NOR support (switched CS by sw5/C)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- squashed overlay-patch and converted sd/emmc dts to overlay too
- moved mmc-regulators to base dts
- changed common dtsi to (base dts) and overlay extension to dtso

v6:
- drop usb 5v regulator from bpi-r3
  based on chunfengs response it is only needed if regulator is
  switched (like for otg), usb works without it.

v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
  thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
  - add key suffix like it's done in mt7622-bpi-r64 devicetree
  - add dash in sfp node names
  - use reg as unit for switch-node
  - drop "-3-4" suffix from i2c-pins node name
  - fix order in Makefile
---
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 6 files changed, 631 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96..d5cd7b3e09cf 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
new file mode 100644
index 000000000000..779dc6782bb1
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <8>;
+			max-frequency = <200000000>;
+			cap-mmc-highspeed;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			hs400-ds-delay = <0x14014>;
+			non-removable;
+			no-sd;
+			no-sdio;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
new file mode 100644
index 000000000000..15ee8c568f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi_nand: spi_nand@0 {
+				compatible = "spi-nand";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+				spi-tx-buswidth = <4>;
+				spi-rx-buswidth = <4>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x80000>;
+						read-only;
+					};
+
+					partition@80000 {
+						label = "reserved";
+						reg = <0x80000 0x300000>;
+					};
+
+					partition@380000 {
+						label = "fip";
+						reg = <0x380000 0x200000>;
+						read-only;
+					};
+
+					partition@580000 {
+						label = "ubi";
+						reg = <0x580000 0x7a80000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
new file mode 100644
index 000000000000..84aa229e80f3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			flash@0 {
+				compatible = "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					partition@20000 {
+						label = "reserved";
+						reg = <0x20000 0x20000>;
+					};
+
+					partition@40000 {
+						label = "u-boot-env";
+						reg = <0x40000 0x40000>;
+					};
+
+					partition@80000 {
+						label = "reserved2";
+						reg = <0x80000 0x80000>;
+					};
+
+					partition@100000 {
+						label = "fip";
+						reg = <0x100000 0x80000>;
+						read-only;
+					};
+
+					partition@180000 {
+						label = "recovery";
+						reg = <0x180000 0xa80000>;
+					};
+
+					partition@c00000 {
+						label = "fit";
+						reg = <0xc00000 0x1400000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
new file mode 100644
index 000000000000..08af778d8adc
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+	model = "Bananapi BPI-R3 (sdmmc)";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <4>;
+			max-frequency = <52000000>;
+			cap-sd-highspeed;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
new file mode 100644
index 000000000000..33bd6febc160
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@mediatek.com>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ *          Daniel Golle <daniel@makrotopia.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3";
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dcin: regulator-12vd {
+		compatible = "regulator-fixed";
+		regulator-name = "12vd";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset-key {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps-key {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* i2c of the left SFP cage (wan) */
+	i2c_sfp1: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	/* i2c of the right SFP cage (lan) */
+	i2c_sfp2: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue_led: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3vd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	/* left SFP cage (wan) */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* right SFP cage (lan) */
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		sfp = <&sfp1>;
+		managed = "in-band-status";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_pins>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pio {
+	i2c_pins: i2c-pins {
+		mux {
+			function = "i2c";
+			groups = "i2c";
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_pereset";
+		};
+	};
+
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_0";
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_rx_tx";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_0_rx_tx";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_led_pins: wf-led-pins {
+		mux {
+			function = "led";
+			groups = "wifi_led";
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	status = "okay";
+};
+
+&ssusb {
+	status = "okay";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan0";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan3";
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			label = "lan4";
+			phy-mode = "2500base-x";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
-- 
2.34.1

[PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- SPI-NAND/NOR support (switched CS by sw5/C)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- squashed overlay-patch and converted sd/emmc dts to overlay too
- moved mmc-regulators to base dts
- changed common dtsi to (base dts) and overlay extension to dtso

v6:
- drop usb 5v regulator from bpi-r3
  based on chunfengs response it is only needed if regulator is
  switched (like for otg), usb works without it.

v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
  thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
  - add key suffix like it's done in mt7622-bpi-r64 devicetree
  - add dash in sfp node names
  - use reg as unit for switch-node
  - drop "-3-4" suffix from i2c-pins node name
  - fix order in Makefile
---
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 6 files changed, 631 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96..d5cd7b3e09cf 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
new file mode 100644
index 000000000000..779dc6782bb1
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <8>;
+			max-frequency = <200000000>;
+			cap-mmc-highspeed;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			hs400-ds-delay = <0x14014>;
+			non-removable;
+			no-sd;
+			no-sdio;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
new file mode 100644
index 000000000000..15ee8c568f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi_nand: spi_nand@0 {
+				compatible = "spi-nand";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+				spi-tx-buswidth = <4>;
+				spi-rx-buswidth = <4>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x80000>;
+						read-only;
+					};
+
+					partition@80000 {
+						label = "reserved";
+						reg = <0x80000 0x300000>;
+					};
+
+					partition@380000 {
+						label = "fip";
+						reg = <0x380000 0x200000>;
+						read-only;
+					};
+
+					partition@580000 {
+						label = "ubi";
+						reg = <0x580000 0x7a80000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
new file mode 100644
index 000000000000..84aa229e80f3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			flash@0 {
+				compatible = "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					partition@20000 {
+						label = "reserved";
+						reg = <0x20000 0x20000>;
+					};
+
+					partition@40000 {
+						label = "u-boot-env";
+						reg = <0x40000 0x40000>;
+					};
+
+					partition@80000 {
+						label = "reserved2";
+						reg = <0x80000 0x80000>;
+					};
+
+					partition@100000 {
+						label = "fip";
+						reg = <0x100000 0x80000>;
+						read-only;
+					};
+
+					partition@180000 {
+						label = "recovery";
+						reg = <0x180000 0xa80000>;
+					};
+
+					partition@c00000 {
+						label = "fit";
+						reg = <0xc00000 0x1400000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
new file mode 100644
index 000000000000..08af778d8adc
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+	model = "Bananapi BPI-R3 (sdmmc)";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <4>;
+			max-frequency = <52000000>;
+			cap-sd-highspeed;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
new file mode 100644
index 000000000000..33bd6febc160
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@mediatek.com>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ *          Daniel Golle <daniel@makrotopia.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3";
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dcin: regulator-12vd {
+		compatible = "regulator-fixed";
+		regulator-name = "12vd";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset-key {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps-key {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* i2c of the left SFP cage (wan) */
+	i2c_sfp1: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	/* i2c of the right SFP cage (lan) */
+	i2c_sfp2: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue_led: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3vd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	/* left SFP cage (wan) */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* right SFP cage (lan) */
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		sfp = <&sfp1>;
+		managed = "in-band-status";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_pins>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pio {
+	i2c_pins: i2c-pins {
+		mux {
+			function = "i2c";
+			groups = "i2c";
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_pereset";
+		};
+	};
+
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_0";
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_rx_tx";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_0_rx_tx";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_led_pins: wf-led-pins {
+		mux {
+			function = "led";
+			groups = "wifi_led";
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	status = "okay";
+};
+
+&ssusb {
+	status = "okay";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan0";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan3";
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			label = "lan4";
+			phy-mode = "2500base-x";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
-- 
2.34.1

[PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- SPI-NAND/NOR support (switched CS by sw5/C)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- squashed overlay-patch and converted sd/emmc dts to overlay too
- moved mmc-regulators to base dts
- changed common dtsi to (base dts) and overlay extension to dtso

v6:
- drop usb 5v regulator from bpi-r3
  based on chunfengs response it is only needed if regulator is
  switched (like for otg), usb works without it.

v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
  thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
  - add key suffix like it's done in mt7622-bpi-r64 devicetree
  - add dash in sfp node names
  - use reg as unit for switch-node
  - drop "-3-4" suffix from i2c-pins node name
  - fix order in Makefile
---
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 6 files changed, 631 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96..d5cd7b3e09cf 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
new file mode 100644
index 000000000000..779dc6782bb1
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <8>;
+			max-frequency = <200000000>;
+			cap-mmc-highspeed;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			hs400-ds-delay = <0x14014>;
+			non-removable;
+			no-sd;
+			no-sdio;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
new file mode 100644
index 000000000000..15ee8c568f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi_nand: spi_nand@0 {
+				compatible = "spi-nand";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+				spi-tx-buswidth = <4>;
+				spi-rx-buswidth = <4>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x80000>;
+						read-only;
+					};
+
+					partition@80000 {
+						label = "reserved";
+						reg = <0x80000 0x300000>;
+					};
+
+					partition@380000 {
+						label = "fip";
+						reg = <0x380000 0x200000>;
+						read-only;
+					};
+
+					partition@580000 {
+						label = "ubi";
+						reg = <0x580000 0x7a80000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
new file mode 100644
index 000000000000..84aa229e80f3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			flash@0 {
+				compatible = "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					partition@20000 {
+						label = "reserved";
+						reg = <0x20000 0x20000>;
+					};
+
+					partition@40000 {
+						label = "u-boot-env";
+						reg = <0x40000 0x40000>;
+					};
+
+					partition@80000 {
+						label = "reserved2";
+						reg = <0x80000 0x80000>;
+					};
+
+					partition@100000 {
+						label = "fip";
+						reg = <0x100000 0x80000>;
+						read-only;
+					};
+
+					partition@180000 {
+						label = "recovery";
+						reg = <0x180000 0xa80000>;
+					};
+
+					partition@c00000 {
+						label = "fit";
+						reg = <0xc00000 0x1400000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
new file mode 100644
index 000000000000..08af778d8adc
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+	model = "Bananapi BPI-R3 (sdmmc)";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <4>;
+			max-frequency = <52000000>;
+			cap-sd-highspeed;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
new file mode 100644
index 000000000000..33bd6febc160
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@mediatek.com>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ *          Daniel Golle <daniel@makrotopia.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3";
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dcin: regulator-12vd {
+		compatible = "regulator-fixed";
+		regulator-name = "12vd";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset-key {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps-key {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* i2c of the left SFP cage (wan) */
+	i2c_sfp1: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	/* i2c of the right SFP cage (lan) */
+	i2c_sfp2: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue_led: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3vd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	/* left SFP cage (wan) */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* right SFP cage (lan) */
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		sfp = <&sfp1>;
+		managed = "in-band-status";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_pins>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pio {
+	i2c_pins: i2c-pins {
+		mux {
+			function = "i2c";
+			groups = "i2c";
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_pereset";
+		};
+	};
+
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_0";
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_rx_tx";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_0_rx_tx";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_led_pins: wf-led-pins {
+		mux {
+			function = "led";
+			groups = "wifi_led";
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	status = "okay";
+};
+
+&ssusb {
+	status = "okay";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan0";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan3";
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			label = "lan4";
+			phy-mode = "2500base-x";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- SPI-NAND/NOR support (switched CS by sw5/C)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
changes:
v8:
- drop model string override in emmc-dtso
- drop cs-gpios from spi-nodes
- add interrupt-settings for mt7531 switch

v7:
- squashed overlay-patch and converted sd/emmc dts to overlay too
- moved mmc-regulators to base dts
- changed common dtsi to (base dts) and overlay extension to dtso

v6:
- drop usb 5v regulator from bpi-r3
  based on chunfengs response it is only needed if regulator is
  switched (like for otg), usb works without it.

v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
  thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
  - add key suffix like it's done in mt7622-bpi-r64 devicetree
  - add dash in sfp node names
  - use reg as unit for switch-node
  - drop "-3-4" suffix from i2c-pins node name
  - fix order in Makefile
---
 arch/arm64/boot/dts/mediatek/Makefile         |   5 +
 .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
 .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
 6 files changed, 631 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96..d5cd7b3e09cf 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
new file mode 100644
index 000000000000..779dc6782bb1
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <8>;
+			max-frequency = <200000000>;
+			cap-mmc-highspeed;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			hs400-ds-delay = <0x14014>;
+			non-removable;
+			no-sd;
+			no-sdio;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
new file mode 100644
index 000000000000..15ee8c568f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi_nand: spi_nand@0 {
+				compatible = "spi-nand";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+				spi-tx-buswidth = <4>;
+				spi-rx-buswidth = <4>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x80000>;
+						read-only;
+					};
+
+					partition@80000 {
+						label = "reserved";
+						reg = <0x80000 0x300000>;
+					};
+
+					partition@380000 {
+						label = "fip";
+						reg = <0x380000 0x200000>;
+						read-only;
+					};
+
+					partition@580000 {
+						label = "ubi";
+						reg = <0x580000 0x7a80000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
new file mode 100644
index 000000000000..84aa229e80f3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			flash@0 {
+				compatible = "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					partition@20000 {
+						label = "reserved";
+						reg = <0x20000 0x20000>;
+					};
+
+					partition@40000 {
+						label = "u-boot-env";
+						reg = <0x40000 0x40000>;
+					};
+
+					partition@80000 {
+						label = "reserved2";
+						reg = <0x80000 0x80000>;
+					};
+
+					partition@100000 {
+						label = "fip";
+						reg = <0x100000 0x80000>;
+						read-only;
+					};
+
+					partition@180000 {
+						label = "recovery";
+						reg = <0x180000 0xa80000>;
+					};
+
+					partition@c00000 {
+						label = "fit";
+						reg = <0xc00000 0x1400000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
new file mode 100644
index 000000000000..08af778d8adc
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+	model = "Bananapi BPI-R3 (sdmmc)";
+
+	fragment@0 {
+		target-path = "/soc/mmc@11230000";
+		__overlay__ {
+			bus-width = <4>;
+			max-frequency = <52000000>;
+			cap-sd-highspeed;
+			status = "okay";
+		};
+	};
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
new file mode 100644
index 000000000000..33bd6febc160
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@mediatek.com>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ *          Daniel Golle <daniel@makrotopia.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3";
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dcin: regulator-12vd {
+		compatible = "regulator-fixed";
+		regulator-name = "12vd";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset-key {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps-key {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* i2c of the left SFP cage (wan) */
+	i2c_sfp1: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	/* i2c of the right SFP cage (lan) */
+	i2c_sfp2: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue_led: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3vd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	/* left SFP cage (wan) */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* right SFP cage (lan) */
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		sfp = <&sfp1>;
+		managed = "in-band-status";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_pins>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pio {
+	i2c_pins: i2c-pins {
+		mux {
+			function = "i2c";
+			groups = "i2c";
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_pereset";
+		};
+	};
+
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_0";
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_rx_tx";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_0_rx_tx";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_led_pins: wf-led-pins {
+		mux {
+			function = "led";
+			groups = "wifi_led";
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	status = "okay";
+};
+
+&ssusb {
+	status = "okay";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan0";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan3";
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			label = "lan4";
+			phy-mode = "2500base-x";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Daniel Golle]

On Thu, Dec 29, 2022 at 03:50:23PM +0100, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add support for Bananapi R3 SBC.
> 
> - SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
> - SPI-NAND/NOR support (switched CS by sw5/C)
> - all rj45 ports and both SFP working (eth1/lan4)
> - all USB-Ports + SIM-Slot tested
> - i2c and all uarts tested
> - wifi tested (with eeprom calibration data)
> 
> The device can boot from all 4 storage options. Both, SPI and MMC, can
> be switched using hardware switches on the board, see
> https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
> changes:
> v8:
> - drop model string override in emmc-dtso
> - drop cs-gpios from spi-nodes
> - add interrupt-settings for mt7531 switch
> 
> v7:
> - squashed overlay-patch and converted sd/emmc dts to overlay too
> - moved mmc-regulators to base dts
> - changed common dtsi to (base dts) and overlay extension to dtso
> 
> v6:
> - drop usb 5v regulator from bpi-r3
>   based on chunfengs response it is only needed if regulator is
>   switched (like for otg), usb works without it.
> 
> v4:
> - add PCIe nodes
> - fix sfp-properties of sfp-1 (need to be plural)
>   thx to Denis Odintsov for this
> 
> v3:
> - rename factory-key to reset-key
> - add dcin regulator and add it as input for 3v3 (with renaming)
> - remove memory-node
> - dropped wifi eeprom (calibration) data
> - move mmc0 pinctrl to common dtsi and drop sdcard comment
> - change mmc pull-up/down to have generic bias-pull*
> 
> v2:
> - remove pcie to be added later (discussion about clocks)
> - some fixes based on suggestions on ML
>   - add key suffix like it's done in mt7622-bpi-r64 devicetree
>   - add dash in sfp node names
>   - use reg as unit for switch-node
>   - drop "-3-4" suffix from i2c-pins node name
>   - fix order in Makefile
> ---
>  arch/arm64/boot/dts/mediatek/Makefile         |   5 +
>  .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
>  .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
>  .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
>  6 files changed, 631 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96..d5cd7b3e09cf 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
> new file mode 100644
> index 000000000000..779dc6782bb1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <sam.shih@mediatek.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/mmc@11230000";
> +		__overlay__ {
> +			bus-width = <8>;
> +			max-frequency = <200000000>;
> +			cap-mmc-highspeed;
> +			mmc-hs200-1_8v;
> +			mmc-hs400-1_8v;
> +			hs400-ds-delay = <0x14014>;
> +			non-removable;
> +			no-sd;
> +			no-sdio;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
> new file mode 100644
> index 000000000000..15ee8c568f3c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
> @@ -0,0 +1,55 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
> +/*
> + * Authors: Daniel Golle <daniel@makrotopia.org>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/spi@1100a000";
> +		__overlay__ {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			spi_nand: spi_nand@0 {
> +				compatible = "spi-nand";
> +				reg = <0>;
> +				spi-max-frequency = <10000000>;
> +				spi-tx-buswidth = <4>;
> +				spi-rx-buswidth = <4>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "bl2";
> +						reg = <0x0 0x80000>;
> +						read-only;
> +					};
> +
> +					partition@80000 {
> +						label = "reserved";
> +						reg = <0x80000 0x300000>;
> +					};
> +
> +					partition@380000 {
> +						label = "fip";
> +						reg = <0x380000 0x200000>;
> +						read-only;
> +					};
> +
> +					partition@580000 {
> +						label = "ubi";
> +						reg = <0x580000 0x7a80000>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
> new file mode 100644
> index 000000000000..84aa229e80f3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
> @@ -0,0 +1,68 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
> +/*
> + * Authors: Daniel Golle <daniel@makrotopia.org>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/spi@1100a000";
> +		__overlay__ {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			flash@0 {
> +				compatible = "jedec,spi-nor";
> +				reg = <0>;
> +				spi-max-frequency = <10000000>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "bl2";
> +						reg = <0x0 0x20000>;
> +						read-only;
> +					};
> +
> +					partition@20000 {
> +						label = "reserved";
> +						reg = <0x20000 0x20000>;
> +					};
> +
> +					partition@40000 {
> +						label = "u-boot-env";
> +						reg = <0x40000 0x40000>;
> +					};
> +
> +					partition@80000 {
> +						label = "reserved2";
> +						reg = <0x80000 0x80000>;
> +					};
> +
> +					partition@100000 {
> +						label = "fip";
> +						reg = <0x100000 0x80000>;
> +						read-only;
> +					};
> +
> +					partition@180000 {
> +						label = "recovery";
> +						reg = <0x180000 0xa80000>;
> +					};
> +
> +					partition@c00000 {
> +						label = "fit";
> +						reg = <0xc00000 0x1400000>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> new file mode 100644
> index 000000000000..08af778d8adc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <sam.shih@mediatek.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +	model = "Bananapi BPI-R3 (sdmmc)";

There is another model string here which shouldn't be.

> +
> +	fragment@0 {
> +		target-path = "/soc/mmc@11230000";
> +		__overlay__ {
> +			bus-width = <4>;
> +			max-frequency = <52000000>;
> +			cap-sd-highspeed;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> new file mode 100644
> index 000000000000..33bd6febc160
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> @@ -0,0 +1,450 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Authors: Sam.Shih <sam.shih@mediatek.com>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + *          Daniel Golle <daniel@makrotopia.org>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt65xx.h>
> +
> +#include "mt7986a.dtsi"
> +
> +/ {
> +	model = "Bananapi BPI-R3";
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	dcin: regulator-12vd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "12vd";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		reset-key {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wps-key {
> +			label = "wps";
> +			linux,code = <KEY_WPS_BUTTON>;
> +			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	/* i2c of the left SFP cage (wan) */
> +	i2c_sfp1: i2c-gpio-0 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +
> +	/* i2c of the right SFP cage (lan) */
> +	i2c_sfp2: i2c-gpio-1 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		green_led: led-0 {
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		blue_led: led-1 {
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_STATUS;
> +			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1.8vd";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3.3vd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	/* left SFP cage (wan) */
> +	sfp1: sfp-1 {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c_sfp1>;
> +		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
> +		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	/* right SFP cage (lan) */
> +	sfp2: sfp-2 {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c_sfp2>;
> +		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
> +		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&crypto {
> +	status = "okay";
> +};
> +
> +&eth {
> +	status = "okay";
> +
> +	gmac0: mac@0 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <0>;
> +		phy-mode = "2500base-x";
> +
> +		fixed-link {
> +			speed = <2500>;
> +			full-duplex;
> +			pause;
> +		};
> +	};
> +
> +	gmac1: mac@1 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <1>;
> +		phy-mode = "2500base-x";
> +		sfp = <&sfp1>;
> +		managed = "in-band-status";
> +	};
> +
> +	mdio: mdio-bus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> +
> +&mdio {
> +	switch: switch@31 {
> +		compatible = "mediatek,mt7531";
> +		reg = <31>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
> +		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default", "state_uhs";
> +	pinctrl-0 = <&mmc0_pins_default>;
> +	pinctrl-1 = <&mmc0_pins_uhs>;
> +	vmmc-supply = <&reg_3p3v>;
> +	vqmmc-supply = <&reg_1p8v>;
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c_pins>;
> +	status = "okay";
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_pins>;
> +	status = "okay";
> +};
> +
> +&pcie_phy {
> +	status = "okay";
> +};
> +
> +&pio {
> +	i2c_pins: i2c-pins {
> +		mux {
> +			function = "i2c";
> +			groups = "i2c";
> +		};
> +	};
> +
> +	mmc0_pins_default: mmc0-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	mmc0_pins_uhs: mmc0-uhs-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	pcie_pins: pcie-pins {
> +		mux {
> +			function = "pcie";
> +			groups = "pcie_clk", "pcie_pereset";
> +		};
> +	};
> +
> +	spi_flash_pins: spi-flash-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi0", "spi0_wp_hold";
> +		};
> +	};
> +
> +	spic_pins: spic-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi1_0";
> +		};
> +	};
> +
> +	uart1_pins: uart1-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart1_rx_tx";
> +		};
> +	};
> +
> +	uart2_pins: uart2-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart2_0_rx_tx";
> +		};
> +	};
> +
> +	wf_2g_5g_pins: wf-2g-5g-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_2g", "wf_5g";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_dbdc_pins: wf-dbdc-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_dbdc";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_led_pins: wf-led-pins {
> +		mux {
> +			function = "led";
> +			groups = "wifi_led";
> +		};
> +	};
> +};
> +
> +&spi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi_flash_pins>;
> +	status = "okay";
> +};
> +
> +&spi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spic_pins>;
> +	status = "okay";
> +};
> +
> +&ssusb {
> +	status = "okay";
> +};
> +
> +&switch {
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;
> +			label = "wan";
> +		};
> +
> +		port@1 {
> +			reg = <1>;
> +			label = "lan0";
> +		};
> +
> +		port@2 {
> +			reg = <2>;
> +			label = "lan1";
> +		};
> +
> +		port@3 {
> +			reg = <3>;
> +			label = "lan2";
> +		};
> +
> +		port@4 {
> +			reg = <4>;
> +			label = "lan3";
> +		};
> +
> +		port5: port@5 {
> +			reg = <5>;
> +			label = "lan4";
> +			phy-mode = "2500base-x";
> +			sfp = <&sfp2>;
> +			managed = "in-band-status";
> +		};
> +
> +		port@6 {
> +			reg = <6>;
> +			label = "cpu";
> +			ethernet = <&gmac0>;
> +			phy-mode = "2500base-x";
> +
> +			fixed-link {
> +				speed = <2500>;
> +				full-duplex;
> +				pause;
> +			};
> +		};
> +	};
> +};
> +
> +&trng {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +	status = "okay";
> +};
> +
> +&usb_phy {
> +	status = "okay";
> +};
> +
> +&watchdog {
> +	status = "okay";
> +};
> +
> +&wifi {
> +	status = "okay";
> +	pinctrl-names = "default", "dbdc";
> +	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
> +	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
> +};
> +
> -- 
> 2.34.1
> 
> 

Re: [PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Daniel Golle]

On Thu, Dec 29, 2022 at 03:50:23PM +0100, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add support for Bananapi R3 SBC.
> 
> - SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
> - SPI-NAND/NOR support (switched CS by sw5/C)
> - all rj45 ports and both SFP working (eth1/lan4)
> - all USB-Ports + SIM-Slot tested
> - i2c and all uarts tested
> - wifi tested (with eeprom calibration data)
> 
> The device can boot from all 4 storage options. Both, SPI and MMC, can
> be switched using hardware switches on the board, see
> https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
> changes:
> v8:
> - drop model string override in emmc-dtso
> - drop cs-gpios from spi-nodes
> - add interrupt-settings for mt7531 switch
> 
> v7:
> - squashed overlay-patch and converted sd/emmc dts to overlay too
> - moved mmc-regulators to base dts
> - changed common dtsi to (base dts) and overlay extension to dtso
> 
> v6:
> - drop usb 5v regulator from bpi-r3
>   based on chunfengs response it is only needed if regulator is
>   switched (like for otg), usb works without it.
> 
> v4:
> - add PCIe nodes
> - fix sfp-properties of sfp-1 (need to be plural)
>   thx to Denis Odintsov for this
> 
> v3:
> - rename factory-key to reset-key
> - add dcin regulator and add it as input for 3v3 (with renaming)
> - remove memory-node
> - dropped wifi eeprom (calibration) data
> - move mmc0 pinctrl to common dtsi and drop sdcard comment
> - change mmc pull-up/down to have generic bias-pull*
> 
> v2:
> - remove pcie to be added later (discussion about clocks)
> - some fixes based on suggestions on ML
>   - add key suffix like it's done in mt7622-bpi-r64 devicetree
>   - add dash in sfp node names
>   - use reg as unit for switch-node
>   - drop "-3-4" suffix from i2c-pins node name
>   - fix order in Makefile
> ---
>  arch/arm64/boot/dts/mediatek/Makefile         |   5 +
>  .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
>  .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
>  .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
>  6 files changed, 631 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96..d5cd7b3e09cf 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
> new file mode 100644
> index 000000000000..779dc6782bb1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <sam.shih@mediatek.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/mmc@11230000";
> +		__overlay__ {
> +			bus-width = <8>;
> +			max-frequency = <200000000>;
> +			cap-mmc-highspeed;
> +			mmc-hs200-1_8v;
> +			mmc-hs400-1_8v;
> +			hs400-ds-delay = <0x14014>;
> +			non-removable;
> +			no-sd;
> +			no-sdio;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
> new file mode 100644
> index 000000000000..15ee8c568f3c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
> @@ -0,0 +1,55 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
> +/*
> + * Authors: Daniel Golle <daniel@makrotopia.org>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/spi@1100a000";
> +		__overlay__ {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			spi_nand: spi_nand@0 {
> +				compatible = "spi-nand";
> +				reg = <0>;
> +				spi-max-frequency = <10000000>;
> +				spi-tx-buswidth = <4>;
> +				spi-rx-buswidth = <4>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "bl2";
> +						reg = <0x0 0x80000>;
> +						read-only;
> +					};
> +
> +					partition@80000 {
> +						label = "reserved";
> +						reg = <0x80000 0x300000>;
> +					};
> +
> +					partition@380000 {
> +						label = "fip";
> +						reg = <0x380000 0x200000>;
> +						read-only;
> +					};
> +
> +					partition@580000 {
> +						label = "ubi";
> +						reg = <0x580000 0x7a80000>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
> new file mode 100644
> index 000000000000..84aa229e80f3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
> @@ -0,0 +1,68 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
> +/*
> + * Authors: Daniel Golle <daniel@makrotopia.org>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/spi@1100a000";
> +		__overlay__ {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			flash@0 {
> +				compatible = "jedec,spi-nor";
> +				reg = <0>;
> +				spi-max-frequency = <10000000>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "bl2";
> +						reg = <0x0 0x20000>;
> +						read-only;
> +					};
> +
> +					partition@20000 {
> +						label = "reserved";
> +						reg = <0x20000 0x20000>;
> +					};
> +
> +					partition@40000 {
> +						label = "u-boot-env";
> +						reg = <0x40000 0x40000>;
> +					};
> +
> +					partition@80000 {
> +						label = "reserved2";
> +						reg = <0x80000 0x80000>;
> +					};
> +
> +					partition@100000 {
> +						label = "fip";
> +						reg = <0x100000 0x80000>;
> +						read-only;
> +					};
> +
> +					partition@180000 {
> +						label = "recovery";
> +						reg = <0x180000 0xa80000>;
> +					};
> +
> +					partition@c00000 {
> +						label = "fit";
> +						reg = <0xc00000 0x1400000>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> new file mode 100644
> index 000000000000..08af778d8adc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <sam.shih@mediatek.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +	model = "Bananapi BPI-R3 (sdmmc)";

There is another model string here which shouldn't be.

> +
> +	fragment@0 {
> +		target-path = "/soc/mmc@11230000";
> +		__overlay__ {
> +			bus-width = <4>;
> +			max-frequency = <52000000>;
> +			cap-sd-highspeed;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> new file mode 100644
> index 000000000000..33bd6febc160
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> @@ -0,0 +1,450 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Authors: Sam.Shih <sam.shih@mediatek.com>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + *          Daniel Golle <daniel@makrotopia.org>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt65xx.h>
> +
> +#include "mt7986a.dtsi"
> +
> +/ {
> +	model = "Bananapi BPI-R3";
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	dcin: regulator-12vd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "12vd";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		reset-key {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wps-key {
> +			label = "wps";
> +			linux,code = <KEY_WPS_BUTTON>;
> +			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	/* i2c of the left SFP cage (wan) */
> +	i2c_sfp1: i2c-gpio-0 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +
> +	/* i2c of the right SFP cage (lan) */
> +	i2c_sfp2: i2c-gpio-1 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		green_led: led-0 {
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		blue_led: led-1 {
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_STATUS;
> +			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1.8vd";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3.3vd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	/* left SFP cage (wan) */
> +	sfp1: sfp-1 {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c_sfp1>;
> +		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
> +		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	/* right SFP cage (lan) */
> +	sfp2: sfp-2 {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c_sfp2>;
> +		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
> +		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&crypto {
> +	status = "okay";
> +};
> +
> +&eth {
> +	status = "okay";
> +
> +	gmac0: mac@0 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <0>;
> +		phy-mode = "2500base-x";
> +
> +		fixed-link {
> +			speed = <2500>;
> +			full-duplex;
> +			pause;
> +		};
> +	};
> +
> +	gmac1: mac@1 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <1>;
> +		phy-mode = "2500base-x";
> +		sfp = <&sfp1>;
> +		managed = "in-band-status";
> +	};
> +
> +	mdio: mdio-bus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> +
> +&mdio {
> +	switch: switch@31 {
> +		compatible = "mediatek,mt7531";
> +		reg = <31>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
> +		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default", "state_uhs";
> +	pinctrl-0 = <&mmc0_pins_default>;
> +	pinctrl-1 = <&mmc0_pins_uhs>;
> +	vmmc-supply = <&reg_3p3v>;
> +	vqmmc-supply = <&reg_1p8v>;
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c_pins>;
> +	status = "okay";
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_pins>;
> +	status = "okay";
> +};
> +
> +&pcie_phy {
> +	status = "okay";
> +};
> +
> +&pio {
> +	i2c_pins: i2c-pins {
> +		mux {
> +			function = "i2c";
> +			groups = "i2c";
> +		};
> +	};
> +
> +	mmc0_pins_default: mmc0-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	mmc0_pins_uhs: mmc0-uhs-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	pcie_pins: pcie-pins {
> +		mux {
> +			function = "pcie";
> +			groups = "pcie_clk", "pcie_pereset";
> +		};
> +	};
> +
> +	spi_flash_pins: spi-flash-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi0", "spi0_wp_hold";
> +		};
> +	};
> +
> +	spic_pins: spic-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi1_0";
> +		};
> +	};
> +
> +	uart1_pins: uart1-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart1_rx_tx";
> +		};
> +	};
> +
> +	uart2_pins: uart2-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart2_0_rx_tx";
> +		};
> +	};
> +
> +	wf_2g_5g_pins: wf-2g-5g-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_2g", "wf_5g";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_dbdc_pins: wf-dbdc-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_dbdc";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_led_pins: wf-led-pins {
> +		mux {
> +			function = "led";
> +			groups = "wifi_led";
> +		};
> +	};
> +};
> +
> +&spi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi_flash_pins>;
> +	status = "okay";
> +};
> +
> +&spi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spic_pins>;
> +	status = "okay";
> +};
> +
> +&ssusb {
> +	status = "okay";
> +};
> +
> +&switch {
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;
> +			label = "wan";
> +		};
> +
> +		port@1 {
> +			reg = <1>;
> +			label = "lan0";
> +		};
> +
> +		port@2 {
> +			reg = <2>;
> +			label = "lan1";
> +		};
> +
> +		port@3 {
> +			reg = <3>;
> +			label = "lan2";
> +		};
> +
> +		port@4 {
> +			reg = <4>;
> +			label = "lan3";
> +		};
> +
> +		port5: port@5 {
> +			reg = <5>;
> +			label = "lan4";
> +			phy-mode = "2500base-x";
> +			sfp = <&sfp2>;
> +			managed = "in-band-status";
> +		};
> +
> +		port@6 {
> +			reg = <6>;
> +			label = "cpu";
> +			ethernet = <&gmac0>;
> +			phy-mode = "2500base-x";
> +
> +			fixed-link {
> +				speed = <2500>;
> +				full-duplex;
> +				pause;
> +			};
> +		};
> +	};
> +};
> +
> +&trng {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +	status = "okay";
> +};
> +
> +&usb_phy {
> +	status = "okay";
> +};
> +
> +&watchdog {
> +	status = "okay";
> +};
> +
> +&wifi {
> +	status = "okay";
> +	pinctrl-names = "default", "dbdc";
> +	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
> +	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
> +};
> +
> -- 
> 2.34.1
> 
> 

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Daniel Golle]

On Thu, Dec 29, 2022 at 03:50:23PM +0100, Frank Wunderlich wrote:
> From: Frank Wunderlich <frank-w@public-files.de>
> 
> Add support for Bananapi R3 SBC.
> 
> - SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
> - SPI-NAND/NOR support (switched CS by sw5/C)
> - all rj45 ports and both SFP working (eth1/lan4)
> - all USB-Ports + SIM-Slot tested
> - i2c and all uarts tested
> - wifi tested (with eeprom calibration data)
> 
> The device can boot from all 4 storage options. Both, SPI and MMC, can
> be switched using hardware switches on the board, see
> https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting
> 
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
> changes:
> v8:
> - drop model string override in emmc-dtso
> - drop cs-gpios from spi-nodes
> - add interrupt-settings for mt7531 switch
> 
> v7:
> - squashed overlay-patch and converted sd/emmc dts to overlay too
> - moved mmc-regulators to base dts
> - changed common dtsi to (base dts) and overlay extension to dtso
> 
> v6:
> - drop usb 5v regulator from bpi-r3
>   based on chunfengs response it is only needed if regulator is
>   switched (like for otg), usb works without it.
> 
> v4:
> - add PCIe nodes
> - fix sfp-properties of sfp-1 (need to be plural)
>   thx to Denis Odintsov for this
> 
> v3:
> - rename factory-key to reset-key
> - add dcin regulator and add it as input for 3v3 (with renaming)
> - remove memory-node
> - dropped wifi eeprom (calibration) data
> - move mmc0 pinctrl to common dtsi and drop sdcard comment
> - change mmc pull-up/down to have generic bias-pull*
> 
> v2:
> - remove pcie to be added later (discussion about clocks)
> - some fixes based on suggestions on ML
>   - add key suffix like it's done in mt7622-bpi-r64 devicetree
>   - add dash in sfp node names
>   - use reg as unit for switch-node
>   - drop "-3-4" suffix from i2c-pins node name
>   - fix order in Makefile
> ---
>  arch/arm64/boot/dts/mediatek/Makefile         |   5 +
>  .../mt7986a-bananapi-bpi-r3-emmc.dtso         |  29 ++
>  .../mt7986a-bananapi-bpi-r3-nand.dtso         |  55 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso |  68 +++
>  .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso  |  24 +
>  .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts  | 450 ++++++++++++++++++
>  6 files changed, 631 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> 
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96..d5cd7b3e09cf 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -8,6 +8,11 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtbo
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
> new file mode 100644
> index 000000000000..779dc6782bb1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso
> @@ -0,0 +1,29 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <sam.shih@mediatek.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/mmc@11230000";
> +		__overlay__ {
> +			bus-width = <8>;
> +			max-frequency = <200000000>;
> +			cap-mmc-highspeed;
> +			mmc-hs200-1_8v;
> +			mmc-hs400-1_8v;
> +			hs400-ds-delay = <0x14014>;
> +			non-removable;
> +			no-sd;
> +			no-sdio;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
> new file mode 100644
> index 000000000000..15ee8c568f3c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso
> @@ -0,0 +1,55 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
> +/*
> + * Authors: Daniel Golle <daniel@makrotopia.org>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/spi@1100a000";
> +		__overlay__ {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			spi_nand: spi_nand@0 {
> +				compatible = "spi-nand";
> +				reg = <0>;
> +				spi-max-frequency = <10000000>;
> +				spi-tx-buswidth = <4>;
> +				spi-rx-buswidth = <4>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "bl2";
> +						reg = <0x0 0x80000>;
> +						read-only;
> +					};
> +
> +					partition@80000 {
> +						label = "reserved";
> +						reg = <0x80000 0x300000>;
> +					};
> +
> +					partition@380000 {
> +						label = "fip";
> +						reg = <0x380000 0x200000>;
> +						read-only;
> +					};
> +
> +					partition@580000 {
> +						label = "ubi";
> +						reg = <0x580000 0x7a80000>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
> new file mode 100644
> index 000000000000..84aa229e80f3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso
> @@ -0,0 +1,68 @@
> +/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
> +/*
> + * Authors: Daniel Golle <daniel@makrotopia.org>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	fragment@0 {
> +		target-path = "/soc/spi@1100a000";
> +		__overlay__ {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			flash@0 {
> +				compatible = "jedec,spi-nor";
> +				reg = <0>;
> +				spi-max-frequency = <10000000>;
> +
> +				partitions {
> +					compatible = "fixed-partitions";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					partition@0 {
> +						label = "bl2";
> +						reg = <0x0 0x20000>;
> +						read-only;
> +					};
> +
> +					partition@20000 {
> +						label = "reserved";
> +						reg = <0x20000 0x20000>;
> +					};
> +
> +					partition@40000 {
> +						label = "u-boot-env";
> +						reg = <0x40000 0x40000>;
> +					};
> +
> +					partition@80000 {
> +						label = "reserved2";
> +						reg = <0x80000 0x80000>;
> +					};
> +
> +					partition@100000 {
> +						label = "fip";
> +						reg = <0x100000 0x80000>;
> +						read-only;
> +					};
> +
> +					partition@180000 {
> +						label = "recovery";
> +						reg = <0x180000 0xa80000>;
> +					};
> +
> +					partition@c00000 {
> +						label = "fit";
> +						reg = <0xc00000 0x1400000>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> new file mode 100644
> index 000000000000..08af778d8adc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Author: Sam.Shih <sam.shih@mediatek.com>
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +/ {
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +	model = "Bananapi BPI-R3 (sdmmc)";

There is another model string here which shouldn't be.

> +
> +	fragment@0 {
> +		target-path = "/soc/mmc@11230000";
> +		__overlay__ {
> +			bus-width = <4>;
> +			max-frequency = <52000000>;
> +			cap-sd-highspeed;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> new file mode 100644
> index 000000000000..33bd6febc160
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts
> @@ -0,0 +1,450 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + * Authors: Sam.Shih <sam.shih@mediatek.com>
> + *          Frank Wunderlich <frank-w@public-files.de>
> + *          Daniel Golle <daniel@makrotopia.org>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt65xx.h>
> +
> +#include "mt7986a.dtsi"
> +
> +/ {
> +	model = "Bananapi BPI-R3";
> +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	dcin: regulator-12vd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "12vd";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		reset-key {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wps-key {
> +			label = "wps";
> +			linux,code = <KEY_WPS_BUTTON>;
> +			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	/* i2c of the left SFP cage (wan) */
> +	i2c_sfp1: i2c-gpio-0 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +
> +	/* i2c of the right SFP cage (lan) */
> +	i2c_sfp2: i2c-gpio-1 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		green_led: led-0 {
> +			color = <LED_COLOR_ID_GREEN>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		blue_led: led-1 {
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_STATUS;
> +			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	reg_1p8v: regulator-1p8v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "1.8vd";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3.3vd";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		vin-supply = <&dcin>;
> +	};
> +
> +	/* left SFP cage (wan) */
> +	sfp1: sfp-1 {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c_sfp1>;
> +		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
> +		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	/* right SFP cage (lan) */
> +	sfp2: sfp-2 {
> +		compatible = "sff,sfp";
> +		i2c-bus = <&i2c_sfp2>;
> +		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
> +		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
> +		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
> +		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&crypto {
> +	status = "okay";
> +};
> +
> +&eth {
> +	status = "okay";
> +
> +	gmac0: mac@0 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <0>;
> +		phy-mode = "2500base-x";
> +
> +		fixed-link {
> +			speed = <2500>;
> +			full-duplex;
> +			pause;
> +		};
> +	};
> +
> +	gmac1: mac@1 {
> +		compatible = "mediatek,eth-mac";
> +		reg = <1>;
> +		phy-mode = "2500base-x";
> +		sfp = <&sfp1>;
> +		managed = "in-band-status";
> +	};
> +
> +	mdio: mdio-bus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> +
> +&mdio {
> +	switch: switch@31 {
> +		compatible = "mediatek,mt7531";
> +		reg = <31>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
> +		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default", "state_uhs";
> +	pinctrl-0 = <&mmc0_pins_default>;
> +	pinctrl-1 = <&mmc0_pins_uhs>;
> +	vmmc-supply = <&reg_3p3v>;
> +	vqmmc-supply = <&reg_1p8v>;
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c_pins>;
> +	status = "okay";
> +};
> +
> +&pcie {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie_pins>;
> +	status = "okay";
> +};
> +
> +&pcie_phy {
> +	status = "okay";
> +};
> +
> +&pio {
> +	i2c_pins: i2c-pins {
> +		mux {
> +			function = "i2c";
> +			groups = "i2c";
> +		};
> +	};
> +
> +	mmc0_pins_default: mmc0-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	mmc0_pins_uhs: mmc0-uhs-pins {
> +		mux {
> +			function = "emmc";
> +			groups = "emmc_51";
> +		};
> +		conf-cmd-dat {
> +			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
> +			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
> +			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
> +			input-enable;
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +		conf-clk {
> +			pins = "EMMC_CK";
> +			drive-strength = <6>;
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-ds {
> +			pins = "EMMC_DSL";
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
> +		};
> +		conf-rst {
> +			pins = "EMMC_RSTB";
> +			drive-strength = <4>;
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
> +		};
> +	};
> +
> +	pcie_pins: pcie-pins {
> +		mux {
> +			function = "pcie";
> +			groups = "pcie_clk", "pcie_pereset";
> +		};
> +	};
> +
> +	spi_flash_pins: spi-flash-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi0", "spi0_wp_hold";
> +		};
> +	};
> +
> +	spic_pins: spic-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi1_0";
> +		};
> +	};
> +
> +	uart1_pins: uart1-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart1_rx_tx";
> +		};
> +	};
> +
> +	uart2_pins: uart2-pins {
> +		mux {
> +			function = "uart";
> +			groups = "uart2_0_rx_tx";
> +		};
> +	};
> +
> +	wf_2g_5g_pins: wf-2g-5g-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_2g", "wf_5g";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_dbdc_pins: wf-dbdc-pins {
> +		mux {
> +			function = "wifi";
> +			groups = "wf_dbdc";
> +		};
> +		conf {
> +			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
> +			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
> +			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
> +			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
> +			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
> +			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
> +			       "WF1_TOP_CLK", "WF1_TOP_DATA";
> +			drive-strength = <4>;
> +		};
> +	};
> +
> +	wf_led_pins: wf-led-pins {
> +		mux {
> +			function = "led";
> +			groups = "wifi_led";
> +		};
> +	};
> +};
> +
> +&spi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi_flash_pins>;
> +	status = "okay";
> +};
> +
> +&spi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spic_pins>;
> +	status = "okay";
> +};
> +
> +&ssusb {
> +	status = "okay";
> +};
> +
> +&switch {
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;
> +			label = "wan";
> +		};
> +
> +		port@1 {
> +			reg = <1>;
> +			label = "lan0";
> +		};
> +
> +		port@2 {
> +			reg = <2>;
> +			label = "lan1";
> +		};
> +
> +		port@3 {
> +			reg = <3>;
> +			label = "lan2";
> +		};
> +
> +		port@4 {
> +			reg = <4>;
> +			label = "lan3";
> +		};
> +
> +		port5: port@5 {
> +			reg = <5>;
> +			label = "lan4";
> +			phy-mode = "2500base-x";
> +			sfp = <&sfp2>;
> +			managed = "in-band-status";
> +		};
> +
> +		port@6 {
> +			reg = <6>;
> +			label = "cpu";
> +			ethernet = <&gmac0>;
> +			phy-mode = "2500base-x";
> +
> +			fixed-link {
> +				speed = <2500>;
> +				full-duplex;
> +				pause;
> +			};
> +		};
> +	};
> +};
> +
> +&trng {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +	status = "okay";
> +};
> +
> +&usb_phy {
> +	status = "okay";
> +};
> +
> +&watchdog {
> +	status = "okay";
> +};
> +
> +&wifi {
> +	status = "okay";
> +	pinctrl-names = "default", "dbdc";
> +	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
> +	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
> +};
> +
> -- 
> 2.34.1
> 
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Aw: Re: [PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

Hi

> Gesendet: Donnerstag, 29. Dezember 2022 um 16:06 Uhr
> Von: "Daniel Golle" <daniel@makrotopia.org>

> > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> > new file mode 100644
> > index 000000000000..08af778d8adc
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> > @@ -0,0 +1,24 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2021 MediaTek Inc.
> > + * Author: Sam.Shih <sam.shih@mediatek.com>
> > + */
> > +
> > +/dts-v1/;
> > +/plugin/;
> > +
> > +/ {
> > +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> > +	model = "Bananapi BPI-R3 (sdmmc)";
>
> There is another model string here which shouldn't be.

sorry, missed this one, will drop it in next version

@all: anything else i need to change?

regards Frank

Aw: Re: [PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

Hi

> Gesendet: Donnerstag, 29. Dezember 2022 um 16:06 Uhr
> Von: "Daniel Golle" <daniel@makrotopia.org>

> > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> > new file mode 100644
> > index 000000000000..08af778d8adc
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> > @@ -0,0 +1,24 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2021 MediaTek Inc.
> > + * Author: Sam.Shih <sam.shih@mediatek.com>
> > + */
> > +
> > +/dts-v1/;
> > +/plugin/;
> > +
> > +/ {
> > +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> > +	model = "Bananapi BPI-R3 (sdmmc)";
>
> There is another model string here which shouldn't be.

sorry, missed this one, will drop it in next version

@all: anything else i need to change?

regards Frank

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Aw: Re: [PATCH v8 5/5] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

Hi

> Gesendet: Donnerstag, 29. Dezember 2022 um 16:06 Uhr
> Von: "Daniel Golle" <daniel@makrotopia.org>

> > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> > new file mode 100644
> > index 000000000000..08af778d8adc
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso
> > @@ -0,0 +1,24 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2021 MediaTek Inc.
> > + * Author: Sam.Shih <sam.shih@mediatek.com>
> > + */
> > +
> > +/dts-v1/;
> > +/plugin/;
> > +
> > +/ {
> > +	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
> > +	model = "Bananapi BPI-R3 (sdmmc)";
>
> There is another model string here which shouldn't be.

sorry, missed this one, will drop it in next version

@all: anything else i need to change?

regards Frank

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel