* [PATCH v7 0/7] Add minimal MT8365 and MT8365-EVK support
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
This adds minimal support for the MediaTek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
v7:
- Update GIC information in mt8365.dtsi (thanks to Marc Zyngier for
pointing out the problem)
- Adjust the timer to match the updated GIC information
v6:
- Add systimer in mt8365.dtsi
- Add I/D caches and L2 cache details in mt8365.dtsi
- Move bl31_secmon_reserved from mt8365.dtsi to mt8365-evk.dts
- Fix inconsistent indentation in mt8365-pinctrl example
- Further mt8365.dtsi cleanups
- Submit to additional maintainers spotted by get_maintainer.pl
v5:
- Reorder top-level entries in mediatek,mt8365-pinctrl.yaml to match
example-schema
- Use consistent quotes
v4:
- Remove pins-are-numbered references that have been holding things up
now that the patches removing it from dt-bindings have landed in linux-next
v3:
- Remove a number of components that are not yet supported (they will
come back alongside the corresponding drivers)
- Address issues found by dt_binding_check (mostly fixing pinctrl
bindings)
- Address issues pointed out in comments
- Reorder patches
v2:
- Add missing dt-bindings documentation
- Small cleanups addressing issues in v1 pointed out by Krzysztof Kozlowski
Bernhard Rosenkränzer (4):
dt-bindings: arm64: dts: mediatek: Add mt8365-evk board
dt-bindings: irq: mtk, sysirq: add support for mt8365
dt-bindings: mfd: syscon: Add mt8365-syscfg
dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
Fabien Parent (3):
dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
arm64: dts: mediatek: Initial mt8365-evk support
.../devicetree/bindings/arm/mediatek.yaml | 4 +
.../interrupt-controller/mediatek,sysirq.txt | 1 +
.../devicetree/bindings/mfd/syscon.yaml | 1 +
.../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 +++++++++
.../bindings/usb/mediatek,mtk-xhci.yaml | 1 +
.../bindings/usb/mediatek,mtu3.yaml | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 ++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++
9 files changed, 753 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
--
2.39.0
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v7 0/7] Add minimal MT8365 and MT8365-EVK support
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
This adds minimal support for the MediaTek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
v7:
- Update GIC information in mt8365.dtsi (thanks to Marc Zyngier for
pointing out the problem)
- Adjust the timer to match the updated GIC information
v6:
- Add systimer in mt8365.dtsi
- Add I/D caches and L2 cache details in mt8365.dtsi
- Move bl31_secmon_reserved from mt8365.dtsi to mt8365-evk.dts
- Fix inconsistent indentation in mt8365-pinctrl example
- Further mt8365.dtsi cleanups
- Submit to additional maintainers spotted by get_maintainer.pl
v5:
- Reorder top-level entries in mediatek,mt8365-pinctrl.yaml to match
example-schema
- Use consistent quotes
v4:
- Remove pins-are-numbered references that have been holding things up
now that the patches removing it from dt-bindings have landed in linux-next
v3:
- Remove a number of components that are not yet supported (they will
come back alongside the corresponding drivers)
- Address issues found by dt_binding_check (mostly fixing pinctrl
bindings)
- Address issues pointed out in comments
- Reorder patches
v2:
- Add missing dt-bindings documentation
- Small cleanups addressing issues in v1 pointed out by Krzysztof Kozlowski
Bernhard Rosenkränzer (4):
dt-bindings: arm64: dts: mediatek: Add mt8365-evk board
dt-bindings: irq: mtk, sysirq: add support for mt8365
dt-bindings: mfd: syscon: Add mt8365-syscfg
dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
Fabien Parent (3):
dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
arm64: dts: mediatek: Initial mt8365-evk support
.../devicetree/bindings/arm/mediatek.yaml | 4 +
.../interrupt-controller/mediatek,sysirq.txt | 1 +
.../devicetree/bindings/mfd/syscon.yaml | 1 +
.../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 +++++++++
.../bindings/usb/mediatek,mtk-xhci.yaml | 1 +
.../bindings/usb/mediatek,mtu3.yaml | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 ++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++
9 files changed, 753 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v7 1/7] dt-bindings: arm64: dts: mediatek: Add mt8365-evk board
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Add bindings for the Mediatek mt8365-evk board.
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
Documentation/devicetree/bindings/arm/mediatek.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index 2275e5d93721b..ae12b1cab9fbd 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -244,6 +244,10 @@ properties:
- enum:
- mediatek,mt8183-pumpkin
- const: mediatek,mt8183
+ - items:
+ - enum:
+ - mediatek,mt8365-evk
+ - const: mediatek,mt8365
- items:
- enum:
- mediatek,mt8516-pumpkin
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 1/7] dt-bindings: arm64: dts: mediatek: Add mt8365-evk board
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Add bindings for the Mediatek mt8365-evk board.
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
Documentation/devicetree/bindings/arm/mediatek.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index 2275e5d93721b..ae12b1cab9fbd 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -244,6 +244,10 @@ properties:
- enum:
- mediatek,mt8183-pumpkin
- const: mediatek,mt8183
+ - items:
+ - enum:
+ - mediatek,mt8365-evk
+ - const: mediatek,mt8365
- items:
- enum:
- mediatek,mt8516-pumpkin
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 2/7] dt-bindings: irq: mtk, sysirq: add support for mt8365
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Add binding documentation of mediatek,sysirq for mt8365 SoC.
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
.../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index 84ced3f4179b9..3ffc60184e445 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -25,6 +25,7 @@ Required properties:
"mediatek,mt6577-sysirq": for MT6577
"mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712
"mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701
+ "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq": for MT8365
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
- reg: Physical base address of the intpol registers and length of memory
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 2/7] dt-bindings: irq: mtk, sysirq: add support for mt8365
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Add binding documentation of mediatek,sysirq for mt8365 SoC.
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
.../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index 84ced3f4179b9..3ffc60184e445 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -25,6 +25,7 @@ Required properties:
"mediatek,mt6577-sysirq": for MT6577
"mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712
"mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701
+ "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq": for MT8365
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
- reg: Physical base address of the intpol registers and length of memory
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 3/7] dt-bindings: mfd: syscon: Add mt8365-syscfg
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Document Mediatek mt8365-syscfg
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
index 1b01bd0104316..7beeb0abc4db0 100644
--- a/Documentation/devicetree/bindings/mfd/syscon.yaml
+++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -50,6 +50,7 @@ properties:
- marvell,armada-3700-usb2-host-misc
- mediatek,mt8135-pctl-a-syscfg
- mediatek,mt8135-pctl-b-syscfg
+ - mediatek,mt8365-syscfg
- microchip,lan966x-cpu-syscon
- microchip,sparx5-cpu-syscon
- mstar,msc313-pmsleep
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 3/7] dt-bindings: mfd: syscon: Add mt8365-syscfg
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Document Mediatek mt8365-syscfg
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
index 1b01bd0104316..7beeb0abc4db0 100644
--- a/Documentation/devicetree/bindings/mfd/syscon.yaml
+++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -50,6 +50,7 @@ properties:
- marvell,armada-3700-usb2-host-misc
- mediatek,mt8135-pctl-a-syscfg
- mediatek,mt8135-pctl-b-syscfg
+ - mediatek,mt8365-syscfg
- microchip,lan966x-cpu-syscon
- microchip,sparx5-cpu-syscon
- mstar,msc313-pmsleep
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Add devicetree bindings for Mediatek MT8365 pinctrl driver.
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
---
.../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 ++++++++++++++++++
1 file changed, 197 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
new file mode 100644
index 0000000000000..4b96884a1afc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
@@ -0,0 +1,197 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8365-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT8365 Pin Controller
+
+maintainers:
+ - Zhiyong Tao <zhiyong.tao@mediatek.com>
+ - Bernhard Rosenkränzer <bero@baylibre.com>
+
+description: |
+ The MediaTek's MT8365 Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ const: mediatek,mt8365-pinctrl
+
+ reg:
+ maxItems: 1
+
+ mediatek,pctl-regmap:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ maxItems: 1
+ minItems: 1
+ maxItems: 2
+ description: |
+ Should be phandles of the syscfg node.
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+patternProperties:
+ "-pins$":
+ type: object
+ additionalProperties: false
+ patternProperties:
+ "pins$":
+ type: object
+ additionalProperties: false
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and input
+ schmitt.
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+
+ properties:
+ pinmux:
+ description:
+ integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are
+ defined as macros in <soc>-pinfunc.h directly.
+
+ bias-disable: true
+
+ bias-pull-up:
+ description: |
+ Besides generic pinconfig options, it can be used as the pull up
+ settings for 2 pull resistors, R0 and R1. User can configure those
+ special pins.
+
+ bias-pull-down: true
+
+ input-enable: true
+
+ input-disable: true
+
+ output-low: true
+
+ output-high: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ mediatek,drive-strength-adv:
+ description: |
+ Describe the specific driving setup property.
+ For I2C pins, the existing generic driving setup can only support
+ 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
+ can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
+ driving setup, the existing generic setup will be disabled.
+ The specific driving setup is controlled by E1E0EN.
+ When E1=0/E0=0, the strength is 0.125mA.
+ When E1=0/E0=1, the strength is 0.25mA.
+ When E1=1/E0=0, the strength is 0.5mA.
+ When E1=1/E0=1, the strength is 1mA.
+ EN is used to enable or disable the specific driving setup.
+ Valid arguments are described as below:
+ 0: (E1, E0, EN) = (0, 0, 0)
+ 1: (E1, E0, EN) = (0, 0, 1)
+ 2: (E1, E0, EN) = (0, 1, 0)
+ 3: (E1, E0, EN) = (0, 1, 1)
+ 4: (E1, E0, EN) = (1, 0, 0)
+ 5: (E1, E0, EN) = (1, 0, 1)
+ 6: (E1, E0, EN) = (1, 1, 0)
+ 7: (E1, E0, EN) = (1, 1, 1)
+ So the valid arguments are from 0 to 7.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ mediatek,pull-up-adv:
+ description: |
+ Pull up setings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,pull-down-adv:
+ description: |
+ Pull down settings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,tdsel:
+ description: |
+ An integer describing the steps for output level shifter duty
+ cycle when asserted (high pulse width adjustment). Valid arguments
+ are from 0 to 15.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ mediatek,rdsel:
+ description: |
+ An integer describing the steps for input level shifter duty cycle
+ when asserted (high pulse width adjustment). Valid arguments are
+ from 0 to 63.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ required:
+ - pinmux
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - "#gpio-cells"
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+
+ pio-pins {
+ pins {
+ pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ bias-pull-up;
+ };
+ };
+ };
+ };
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Add devicetree bindings for Mediatek MT8365 pinctrl driver.
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
---
.../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 ++++++++++++++++++
1 file changed, 197 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
new file mode 100644
index 0000000000000..4b96884a1afc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
@@ -0,0 +1,197 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8365-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT8365 Pin Controller
+
+maintainers:
+ - Zhiyong Tao <zhiyong.tao@mediatek.com>
+ - Bernhard Rosenkränzer <bero@baylibre.com>
+
+description: |
+ The MediaTek's MT8365 Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ const: mediatek,mt8365-pinctrl
+
+ reg:
+ maxItems: 1
+
+ mediatek,pctl-regmap:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ maxItems: 1
+ minItems: 1
+ maxItems: 2
+ description: |
+ Should be phandles of the syscfg node.
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+patternProperties:
+ "-pins$":
+ type: object
+ additionalProperties: false
+ patternProperties:
+ "pins$":
+ type: object
+ additionalProperties: false
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and input
+ schmitt.
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+
+ properties:
+ pinmux:
+ description:
+ integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are
+ defined as macros in <soc>-pinfunc.h directly.
+
+ bias-disable: true
+
+ bias-pull-up:
+ description: |
+ Besides generic pinconfig options, it can be used as the pull up
+ settings for 2 pull resistors, R0 and R1. User can configure those
+ special pins.
+
+ bias-pull-down: true
+
+ input-enable: true
+
+ input-disable: true
+
+ output-low: true
+
+ output-high: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ mediatek,drive-strength-adv:
+ description: |
+ Describe the specific driving setup property.
+ For I2C pins, the existing generic driving setup can only support
+ 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
+ can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
+ driving setup, the existing generic setup will be disabled.
+ The specific driving setup is controlled by E1E0EN.
+ When E1=0/E0=0, the strength is 0.125mA.
+ When E1=0/E0=1, the strength is 0.25mA.
+ When E1=1/E0=0, the strength is 0.5mA.
+ When E1=1/E0=1, the strength is 1mA.
+ EN is used to enable or disable the specific driving setup.
+ Valid arguments are described as below:
+ 0: (E1, E0, EN) = (0, 0, 0)
+ 1: (E1, E0, EN) = (0, 0, 1)
+ 2: (E1, E0, EN) = (0, 1, 0)
+ 3: (E1, E0, EN) = (0, 1, 1)
+ 4: (E1, E0, EN) = (1, 0, 0)
+ 5: (E1, E0, EN) = (1, 0, 1)
+ 6: (E1, E0, EN) = (1, 1, 0)
+ 7: (E1, E0, EN) = (1, 1, 1)
+ So the valid arguments are from 0 to 7.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ mediatek,pull-up-adv:
+ description: |
+ Pull up setings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,pull-down-adv:
+ description: |
+ Pull down settings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,tdsel:
+ description: |
+ An integer describing the steps for output level shifter duty
+ cycle when asserted (high pulse width adjustment). Valid arguments
+ are from 0 to 15.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ mediatek,rdsel:
+ description: |
+ An integer describing the steps for input level shifter duty cycle
+ when asserted (high pulse width adjustment). Valid arguments are
+ from 0 to 63.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ required:
+ - pinmux
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - "#gpio-cells"
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+
+ pio-pins {
+ pins {
+ pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ bias-pull-up;
+ };
+ };
+ };
+ };
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 5/7] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
From: Fabien Parent <fparent@baylibre.com>
Add binding documentation for the MT8365 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
index 7168110e2f9de..d2655173e108c 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
@@ -28,6 +28,7 @@ properties:
- mediatek,mt8188-mtu3
- mediatek,mt8192-mtu3
- mediatek,mt8195-mtu3
+ - mediatek,mt8365-mtu3
- const: mediatek,mtu3
reg:
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 5/7] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
From: Fabien Parent <fparent@baylibre.com>
Add binding documentation for the MT8365 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
index 7168110e2f9de..d2655173e108c 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
@@ -28,6 +28,7 @@ properties:
- mediatek,mt8188-mtu3
- mediatek,mt8192-mtu3
- mediatek,mt8195-mtu3
+ - mediatek,mt8365-mtu3
- const: mediatek,mtu3
reg:
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 6/7] dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
From: Fabien Parent <fparent@baylibre.com>
Add binding documentation for the MT8365 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Cleanups suggested by reviewers]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index a3c37944c6305..c119caa9ad168 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -35,6 +35,7 @@ properties:
- mediatek,mt8188-xhci
- mediatek,mt8192-xhci
- mediatek,mt8195-xhci
+ - mediatek,mt8365-xhci
- const: mediatek,mtk-xhci
reg:
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 6/7] dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
From: Fabien Parent <fparent@baylibre.com>
Add binding documentation for the MT8365 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Cleanups suggested by reviewers]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index a3c37944c6305..c119caa9ad168 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -35,6 +35,7 @@ properties:
- mediatek,mt8188-xhci
- mediatek,mt8192-xhci
- mediatek,mt8195-xhci
+ - mediatek,mt8365-xhci
- const: mediatek,mtk-xhci
reg:
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
From: Fabien Parent <fparent@baylibre.com>
This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++++
3 files changed, 548 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..275ea3a0e7085
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+ model = "MediaTek MT8365 Open Platform EVK";
+ compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+
+ key-volume-up {
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ label = "volume_up";
+ linux,code = <KEY_VOLUMEUP>;
+ wakeup-source;
+ debounce-interval = <15>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0xc0000000>;
+ };
+
+ usb_otg_vbus: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_reserved: secmon@43000000 {
+ no-map;
+ reg = <0 0x43000000 0 0x20000>;
+ };
+
+ /* 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee@43200000 {
+ no-map;
+ reg = <0 0x43200000 0 0x00c00000>;
+ };
+ };
+};
+
+&pio {
+ gpio_keys: gpio-keys-pins {
+ pins {
+ pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins {
+ pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+ <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins {
+ pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+ <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ pins {
+ pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+ <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+ };
+ };
+
+ usb_pins: usb-pins {
+ pins-id {
+ pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-usb0-vbus {
+ pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+ output-high;
+ };
+
+ pin-usb1-vbus {
+ pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+ output-high;
+ };
+ };
+
+ pwm_pins: pwm-pins {
+ pins {
+ pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+ <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..a32f2b7507be3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "mediatek,mt8365";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
+ cache-unified;
+ };
+ };
+
+ clk26m: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x10000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8365-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg: syscon@10001000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8365-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ syscfg_pctl: syscfg-pctl@10005000 {
+ compatible = "mediatek,mt8365-syscfg", "syscon";
+ reg = <0 0x10005000 0 0x1000>;
+ };
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8365-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ keypad: keypad@10010000 {
+ compatible = "mediatek,mt6779-keypad";
+ reg = <0 0x10010000 0 0x1000>;
+ wakeup-source;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+ clocks = <&clk26m>;
+ clock-names = "kpd";
+ status = "disabled";
+ };
+
+ mcucfg: syscon@10200000 {
+ compatible = "mediatek,mt8365-mcucfg", "syscon";
+ reg = <0 0x10200000 0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+ sysirq: interrupt-controller@10200a80 {
+ compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10200a80 0 0x20>;
+ };
+
+ infracfg_nao: infracfg@1020e000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x1020e000 0 0x1000>;
+ };
+
+ rng: rng@1020f000 {
+ compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_IFR_TRNG>;
+ clock-names = "rng";
+ };
+
+ apdma: dma-controller@11000280 {
+ compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+ reg = <0 0x11000280 0 0x80>,
+ <0 0x11000300 0 0x80>,
+ <0 0x11000380 0 0x80>,
+ <0 0x11000400 0 0x80>,
+ <0 0x11000580 0 0x80>,
+ <0 0x11000600 0 0x80>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+ dma-requests = <6>;
+ clocks = <&infracfg CLK_IFR_AP_DMA>;
+ clock-names = "apdma";
+ #dma-cells = <1>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x1000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 0>, <&apdma 1>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x1000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 2>, <&apdma 3>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 4>, <&apdma 5>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ pwm: pwm@11006000 {
+ compatible = "mediatek,mt8365-pwm";
+ reg = <0 0x11006000 0 0x1000>;
+ #pwm-cells = <2>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+ <&infracfg CLK_IFR_PWM>,
+ <&infracfg CLK_IFR_PWM1>,
+ <&infracfg CLK_IFR_PWM2>,
+ <&infracfg CLK_IFR_PWM3>;
+ clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+ };
+
+ spi: spi@1100a000 {
+ compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+ <&topckgen CLK_TOP_SPI_SEL>,
+ <&infracfg CLK_IFR_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ ssusb: usb@11201000 {
+ compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+ reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u2port1 PHY_TYPE_USB2>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: usb@11200000 {
+ compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>,
+ <&infracfg CLK_IFR_SSUSB_XHCI>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck",
+ "dma_ck", "xhci_ck";
+ status = "disabled";
+ };
+ };
+
+ u3phy: phy@11cc0000 {
+ compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #phy-cells = <1>;
+ ranges;
+
+ u2port0: usb-phy@11cc0000 {
+ reg = <0 0x11cc0000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u2port1: usb-phy@11cc1000 {
+ reg = <0 0x11cc1000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ system_clk: dummy13m {
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ #clock-cells = <0>;
+ };
+
+ systimer: timer@10017000 {
+ compatible = "mediatek,mt6795-systimer";
+ reg = <0 0x10017000 0 0x10>;
+ interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&system_clk>;
+ clock-names = "clk13m";
+ };
+};
--
2.39.0
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support
@ 2023-01-01 22:01 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-01 22:01 UTC (permalink / raw)
To: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
From: Fabien Parent <fparent@baylibre.com>
This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++++
3 files changed, 548 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..275ea3a0e7085
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+ model = "MediaTek MT8365 Open Platform EVK";
+ compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+
+ key-volume-up {
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ label = "volume_up";
+ linux,code = <KEY_VOLUMEUP>;
+ wakeup-source;
+ debounce-interval = <15>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0xc0000000>;
+ };
+
+ usb_otg_vbus: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_reserved: secmon@43000000 {
+ no-map;
+ reg = <0 0x43000000 0 0x20000>;
+ };
+
+ /* 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee@43200000 {
+ no-map;
+ reg = <0 0x43200000 0 0x00c00000>;
+ };
+ };
+};
+
+&pio {
+ gpio_keys: gpio-keys-pins {
+ pins {
+ pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins {
+ pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+ <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins {
+ pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+ <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ pins {
+ pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+ <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+ };
+ };
+
+ usb_pins: usb-pins {
+ pins-id {
+ pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-usb0-vbus {
+ pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+ output-high;
+ };
+
+ pin-usb1-vbus {
+ pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+ output-high;
+ };
+ };
+
+ pwm_pins: pwm-pins {
+ pins {
+ pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+ <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..a32f2b7507be3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "mediatek,mt8365";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
+ cache-unified;
+ };
+ };
+
+ clk26m: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x10000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8365-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg: syscon@10001000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8365-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ syscfg_pctl: syscfg-pctl@10005000 {
+ compatible = "mediatek,mt8365-syscfg", "syscon";
+ reg = <0 0x10005000 0 0x1000>;
+ };
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8365-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ keypad: keypad@10010000 {
+ compatible = "mediatek,mt6779-keypad";
+ reg = <0 0x10010000 0 0x1000>;
+ wakeup-source;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+ clocks = <&clk26m>;
+ clock-names = "kpd";
+ status = "disabled";
+ };
+
+ mcucfg: syscon@10200000 {
+ compatible = "mediatek,mt8365-mcucfg", "syscon";
+ reg = <0 0x10200000 0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+ sysirq: interrupt-controller@10200a80 {
+ compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10200a80 0 0x20>;
+ };
+
+ infracfg_nao: infracfg@1020e000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x1020e000 0 0x1000>;
+ };
+
+ rng: rng@1020f000 {
+ compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_IFR_TRNG>;
+ clock-names = "rng";
+ };
+
+ apdma: dma-controller@11000280 {
+ compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+ reg = <0 0x11000280 0 0x80>,
+ <0 0x11000300 0 0x80>,
+ <0 0x11000380 0 0x80>,
+ <0 0x11000400 0 0x80>,
+ <0 0x11000580 0 0x80>,
+ <0 0x11000600 0 0x80>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+ dma-requests = <6>;
+ clocks = <&infracfg CLK_IFR_AP_DMA>;
+ clock-names = "apdma";
+ #dma-cells = <1>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x1000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 0>, <&apdma 1>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x1000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 2>, <&apdma 3>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 4>, <&apdma 5>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ pwm: pwm@11006000 {
+ compatible = "mediatek,mt8365-pwm";
+ reg = <0 0x11006000 0 0x1000>;
+ #pwm-cells = <2>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+ <&infracfg CLK_IFR_PWM>,
+ <&infracfg CLK_IFR_PWM1>,
+ <&infracfg CLK_IFR_PWM2>,
+ <&infracfg CLK_IFR_PWM3>;
+ clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+ };
+
+ spi: spi@1100a000 {
+ compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+ <&topckgen CLK_TOP_SPI_SEL>,
+ <&infracfg CLK_IFR_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ ssusb: usb@11201000 {
+ compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+ reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u2port1 PHY_TYPE_USB2>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: usb@11200000 {
+ compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>,
+ <&infracfg CLK_IFR_SSUSB_XHCI>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck",
+ "dma_ck", "xhci_ck";
+ status = "disabled";
+ };
+ };
+
+ u3phy: phy@11cc0000 {
+ compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #phy-cells = <1>;
+ ranges;
+
+ u2port0: usb-phy@11cc0000 {
+ reg = <0 0x11cc0000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u2port1: usb-phy@11cc1000 {
+ reg = <0 0x11cc1000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ system_clk: dummy13m {
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ #clock-cells = <0>;
+ };
+
+ systimer: timer@10017000 {
+ compatible = "mediatek,mt6795-systimer";
+ reg = <0 0x10017000 0 0x10>;
+ interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&system_clk>;
+ clock-names = "clk13m";
+ };
+};
--
2.39.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 30+ messages in thread
* Re: [PATCH v7 3/7] dt-bindings: mfd: syscon: Add mt8365-syscfg
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-02 12:09 ` AngeloGioacchino Del Regno
-1 siblings, 0 replies; 30+ messages in thread
From: AngeloGioacchino Del Regno @ 2023-01-02 12:09 UTC (permalink / raw)
To: Bernhard Rosenkränzer, devicetree, linux-kernel, linux-gpio,
linux-arm-kernel, linux-mediatek, linux-usb, robh+dt,
krzysztof.kozlowski+dt, tglx, maz, lee, linus.walleij,
matthias.bgg, chunfeng.yun, gregkh, allen-kh.cheng, nfraprado,
sean.wang, zhiyong.tao
Il 01/01/23 23:01, Bernhard Rosenkränzer ha scritto:
> Document Mediatek mt8365-syscfg
>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 3/7] dt-bindings: mfd: syscon: Add mt8365-syscfg
@ 2023-01-02 12:09 ` AngeloGioacchino Del Regno
0 siblings, 0 replies; 30+ messages in thread
From: AngeloGioacchino Del Regno @ 2023-01-02 12:09 UTC (permalink / raw)
To: Bernhard Rosenkränzer, devicetree, linux-kernel, linux-gpio,
linux-arm-kernel, linux-mediatek, linux-usb, robh+dt,
krzysztof.kozlowski+dt, tglx, maz, lee, linus.walleij,
matthias.bgg, chunfeng.yun, gregkh, allen-kh.cheng, nfraprado,
sean.wang, zhiyong.tao
Il 01/01/23 23:01, Bernhard Rosenkränzer ha scritto:
> Document Mediatek mt8365-syscfg
>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 5/7] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-02 12:09 ` AngeloGioacchino Del Regno
-1 siblings, 0 replies; 30+ messages in thread
From: AngeloGioacchino Del Regno @ 2023-01-02 12:09 UTC (permalink / raw)
To: Bernhard Rosenkränzer, devicetree, linux-kernel, linux-gpio,
linux-arm-kernel, linux-mediatek, linux-usb, robh+dt,
krzysztof.kozlowski+dt, tglx, maz, lee, linus.walleij,
matthias.bgg, chunfeng.yun, gregkh, allen-kh.cheng, nfraprado,
sean.wang, zhiyong.tao
Il 01/01/23 23:01, Bernhard Rosenkränzer ha scritto:
> From: Fabien Parent <fparent@baylibre.com>
>
> Add binding documentation for the MT8365 SoC.
>
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 5/7] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
@ 2023-01-02 12:09 ` AngeloGioacchino Del Regno
0 siblings, 0 replies; 30+ messages in thread
From: AngeloGioacchino Del Regno @ 2023-01-02 12:09 UTC (permalink / raw)
To: Bernhard Rosenkränzer, devicetree, linux-kernel, linux-gpio,
linux-arm-kernel, linux-mediatek, linux-usb, robh+dt,
krzysztof.kozlowski+dt, tglx, maz, lee, linus.walleij,
matthias.bgg, chunfeng.yun, gregkh, allen-kh.cheng, nfraprado,
sean.wang, zhiyong.tao
Il 01/01/23 23:01, Bernhard Rosenkränzer ha scritto:
> From: Fabien Parent <fparent@baylibre.com>
>
> Add binding documentation for the MT8365 SoC.
>
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-08 20:23 ` Rob Herring
-1 siblings, 0 replies; 30+ messages in thread
From: Rob Herring @ 2023-01-08 20:23 UTC (permalink / raw)
To: Bernhard Rosenkränzer
Cc: linux-usb, linux-gpio, krzysztof.kozlowski+dt, linux-mediatek,
sean.wang, chunfeng.yun, zhiyong.tao, linux-arm-kernel, tglx,
lee, gregkh, linus.walleij, devicetree,
angelogioacchino.delregno, maz, linux-kernel, nfraprado,
matthias.bgg, allen-kh.cheng, robh+dt
On Sun, 01 Jan 2023 23:01:46 +0100, Bernhard Rosenkränzer wrote:
> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> ---
> .../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 ++++++++++++++++++
> 1 file changed, 197 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
@ 2023-01-08 20:23 ` Rob Herring
0 siblings, 0 replies; 30+ messages in thread
From: Rob Herring @ 2023-01-08 20:23 UTC (permalink / raw)
To: Bernhard Rosenkränzer
Cc: linux-usb, linux-gpio, krzysztof.kozlowski+dt, linux-mediatek,
sean.wang, chunfeng.yun, zhiyong.tao, linux-arm-kernel, tglx,
lee, gregkh, linus.walleij, devicetree,
angelogioacchino.delregno, maz, linux-kernel, nfraprado,
matthias.bgg, allen-kh.cheng, robh+dt
On Sun, 01 Jan 2023 23:01:46 +0100, Bernhard Rosenkränzer wrote:
> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> ---
> .../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 ++++++++++++++++++
> 1 file changed, 197 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-09 13:35 ` Linus Walleij
-1 siblings, 0 replies; 30+ messages in thread
From: Linus Walleij @ 2023-01-09 13:35 UTC (permalink / raw)
To: Bernhard Rosenkränzer
Cc: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
On Sun, Jan 1, 2023 at 11:01 PM Bernhard Rosenkränzer <bero@baylibre.com> wrote:
> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Looks good to me, do you want me to just apply this one patch to the
pin control tree?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
@ 2023-01-09 13:35 ` Linus Walleij
0 siblings, 0 replies; 30+ messages in thread
From: Linus Walleij @ 2023-01-09 13:35 UTC (permalink / raw)
To: Bernhard Rosenkränzer
Cc: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, matthias.bgg, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
On Sun, Jan 1, 2023 at 11:01 PM Bernhard Rosenkränzer <bero@baylibre.com> wrote:
> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
>
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Looks good to me, do you want me to just apply this one patch to the
pin control tree?
Yours,
Linus Walleij
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
2023-01-09 13:35 ` Linus Walleij
@ 2023-01-19 18:21 ` Matthias Brugger
-1 siblings, 0 replies; 30+ messages in thread
From: Matthias Brugger @ 2023-01-19 18:21 UTC (permalink / raw)
To: Linus Walleij, Bernhard Rosenkränzer
Cc: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, chunfeng.yun, gregkh, angelogioacchino.delregno,
allen-kh.cheng, nfraprado, sean.wang, zhiyong.tao
On 09/01/2023 14:35, Linus Walleij wrote:
> On Sun, Jan 1, 2023 at 11:01 PM Bernhard Rosenkränzer <bero@baylibre.com> wrote:
>
>> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
>>
>> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
>
> Looks good to me, do you want me to just apply this one patch to the
> pin control tree?
>
Yes please.
Regards,
Matthias
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
@ 2023-01-19 18:21 ` Matthias Brugger
0 siblings, 0 replies; 30+ messages in thread
From: Matthias Brugger @ 2023-01-19 18:21 UTC (permalink / raw)
To: Linus Walleij, Bernhard Rosenkränzer
Cc: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, chunfeng.yun, gregkh, angelogioacchino.delregno,
allen-kh.cheng, nfraprado, sean.wang, zhiyong.tao
On 09/01/2023 14:35, Linus Walleij wrote:
> On Sun, Jan 1, 2023 at 11:01 PM Bernhard Rosenkränzer <bero@baylibre.com> wrote:
>
>> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
>>
>> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
>
> Looks good to me, do you want me to just apply this one patch to the
> pin control tree?
>
Yes please.
Regards,
Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support
2023-01-01 22:01 ` Bernhard Rosenkränzer
@ 2023-01-20 10:57 ` Matthias Brugger
-1 siblings, 0 replies; 30+ messages in thread
From: Matthias Brugger @ 2023-01-20 10:57 UTC (permalink / raw)
To: Bernhard Rosenkränzer, devicetree, linux-kernel, linux-gpio,
linux-arm-kernel, linux-mediatek, linux-usb, robh+dt,
krzysztof.kozlowski+dt, tglx, maz, lee, linus.walleij,
chunfeng.yun, gregkh, angelogioacchino.delregno, allen-kh.cheng,
nfraprado, sean.wang, zhiyong.tao
On 01/01/2023 23:01, Bernhard Rosenkränzer wrote:
> From: Fabien Parent <fparent@baylibre.com>
>
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
>
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
> arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++++
> 3 files changed, 548 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96d..d78523c5a7dd6 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> new file mode 100644
> index 0000000000000..275ea3a0e7085
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
[...]
> + apdma: dma-controller@11000280 {
> + compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
> + reg = <0 0x11000280 0 0x80>,
> + <0 0x11000300 0 0x80>,
> + <0 0x11000380 0 0x80>,
> + <0 0x11000400 0 0x80>,
> + <0 0x11000580 0 0x80>,
> + <0 0x11000600 0 0x80>;
> + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
> + dma-requests = <6>;
> + clocks = <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "apdma";
> + #dma-cells = <1>;
> + };
> +
> + uart0: serial@11002000 {
> + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
Unfortunately we are missing this compatible in the binding description.
> + reg = <0 0x11002000 0 0x1000>;
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 0>, <&apdma 1>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + uart1: serial@11003000 {
> + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
> + reg = <0 0x11003000 0 0x1000>;
> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 2>, <&apdma 3>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + uart2: serial@11004000 {
> + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
> + reg = <0 0x11004000 0 0x1000>;
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 4>, <&apdma 5>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + pwm: pwm@11006000 {
> + compatible = "mediatek,mt8365-pwm";
> + reg = <0 0x11006000 0 0x1000>;
> + #pwm-cells = <2>;
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_IFR_PWM_HCLK>,
> + <&infracfg CLK_IFR_PWM>,
> + <&infracfg CLK_IFR_PWM1>,
> + <&infracfg CLK_IFR_PWM2>,
> + <&infracfg CLK_IFR_PWM3>;
> + clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
> + };
> +
> + spi: spi@1100a000 {
> + compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
> + reg = <0 0x1100a000 0 0x100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
> + <&topckgen CLK_TOP_SPI_SEL>,
> + <&infracfg CLK_IFR_SPI0>;
> + clock-names = "parent-clk", "sel-clk", "spi-clk";
> + status = "disabled";
> + };
> +
> + ssusb: usb@11201000 {
> + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
Same here.
> + reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
> + reg-names = "mac", "ippc";
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
> + phys = <&u2port0 PHY_TYPE_USB2>,
> + <&u2port1 PHY_TYPE_USB2>;
> + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> + <&infracfg CLK_IFR_SSUSB_REF>,
> + <&infracfg CLK_IFR_SSUSB_SYS>,
> + <&infracfg CLK_IFR_ICUSB>;
> + clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + status = "disabled";
> +
> + usb_host: usb@11200000 {
> + compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
Same here.
> + reg = <0 0x11200000 0 0x1000>;
> + reg-names = "mac";
> + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> + <&infracfg CLK_IFR_SSUSB_REF>,
> + <&infracfg CLK_IFR_SSUSB_SYS>,
> + <&infracfg CLK_IFR_ICUSB>,
> + <&infracfg CLK_IFR_SSUSB_XHCI>;
> + clock-names = "sys_ck", "ref_ck", "mcu_ck",
> + "dma_ck", "xhci_ck";
> + status = "disabled";
> + };
> + };
> +
> + u3phy: phy@11cc0000 {
> + compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + #phy-cells = <1>;
> + ranges;
> +
> + u2port0: usb-phy@11cc0000 {
> + reg = <0 0x11cc0000 0 0x400>;
> + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> + <&topckgen CLK_TOP_USB20_48M_EN>;
> + clock-names = "ref", "da_ref";
> + #phy-cells = <1>;
> + };
> +
> + u2port1: usb-phy@11cc1000 {
> + reg = <0 0x11cc1000 0 0x400>;
> + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> + <&topckgen CLK_TOP_USB20_48M_EN>;
> + clock-names = "ref", "da_ref";
> + #phy-cells = <1>;
> + };
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + system_clk: dummy13m {
> + compatible = "fixed-clock";
> + clock-frequency = <13000000>;
> + #clock-cells = <0>;
> + };
> +
> + systimer: timer@10017000 {
> + compatible = "mediatek,mt6795-systimer";
Why don't we use a compatible like
"mediatek,mt8365-systimer", "mediatek,mt6795-systimer";
We would need to add this to the binding description as well.
I leave it up to you, but I'd advise to start with a minimal working DT which
includes only the bindings that are already merged. Then we can take the new
devices like mtu3, xhci, spidev or i2c later once they are ready.
Regards,
Matthias
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support
@ 2023-01-20 10:57 ` Matthias Brugger
0 siblings, 0 replies; 30+ messages in thread
From: Matthias Brugger @ 2023-01-20 10:57 UTC (permalink / raw)
To: Bernhard Rosenkränzer, devicetree, linux-kernel, linux-gpio,
linux-arm-kernel, linux-mediatek, linux-usb, robh+dt,
krzysztof.kozlowski+dt, tglx, maz, lee, linus.walleij,
chunfeng.yun, gregkh, angelogioacchino.delregno, allen-kh.cheng,
nfraprado, sean.wang, zhiyong.tao
On 01/01/2023 23:01, Bernhard Rosenkränzer wrote:
> From: Fabien Parent <fparent@baylibre.com>
>
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
>
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
> arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++++
> 3 files changed, 548 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 813e735c5b96d..d78523c5a7dd6 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> new file mode 100644
> index 0000000000000..275ea3a0e7085
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
[...]
> + apdma: dma-controller@11000280 {
> + compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
> + reg = <0 0x11000280 0 0x80>,
> + <0 0x11000300 0 0x80>,
> + <0 0x11000380 0 0x80>,
> + <0 0x11000400 0 0x80>,
> + <0 0x11000580 0 0x80>,
> + <0 0x11000600 0 0x80>;
> + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
> + dma-requests = <6>;
> + clocks = <&infracfg CLK_IFR_AP_DMA>;
> + clock-names = "apdma";
> + #dma-cells = <1>;
> + };
> +
> + uart0: serial@11002000 {
> + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
Unfortunately we are missing this compatible in the binding description.
> + reg = <0 0x11002000 0 0x1000>;
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 0>, <&apdma 1>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + uart1: serial@11003000 {
> + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
> + reg = <0 0x11003000 0 0x1000>;
> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 2>, <&apdma 3>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + uart2: serial@11004000 {
> + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
> + reg = <0 0x11004000 0 0x1000>;
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
> + clock-names = "baud", "bus";
> + dmas = <&apdma 4>, <&apdma 5>;
> + dma-names = "tx", "rx";
> + status = "disabled";
> + };
> +
> + pwm: pwm@11006000 {
> + compatible = "mediatek,mt8365-pwm";
> + reg = <0 0x11006000 0 0x1000>;
> + #pwm-cells = <2>;
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&infracfg CLK_IFR_PWM_HCLK>,
> + <&infracfg CLK_IFR_PWM>,
> + <&infracfg CLK_IFR_PWM1>,
> + <&infracfg CLK_IFR_PWM2>,
> + <&infracfg CLK_IFR_PWM3>;
> + clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
> + };
> +
> + spi: spi@1100a000 {
> + compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
> + reg = <0 0x1100a000 0 0x100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
> + <&topckgen CLK_TOP_SPI_SEL>,
> + <&infracfg CLK_IFR_SPI0>;
> + clock-names = "parent-clk", "sel-clk", "spi-clk";
> + status = "disabled";
> + };
> +
> + ssusb: usb@11201000 {
> + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
Same here.
> + reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
> + reg-names = "mac", "ippc";
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
> + phys = <&u2port0 PHY_TYPE_USB2>,
> + <&u2port1 PHY_TYPE_USB2>;
> + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> + <&infracfg CLK_IFR_SSUSB_REF>,
> + <&infracfg CLK_IFR_SSUSB_SYS>,
> + <&infracfg CLK_IFR_ICUSB>;
> + clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + status = "disabled";
> +
> + usb_host: usb@11200000 {
> + compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
Same here.
> + reg = <0 0x11200000 0 0x1000>;
> + reg-names = "mac";
> + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
> + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
> + <&infracfg CLK_IFR_SSUSB_REF>,
> + <&infracfg CLK_IFR_SSUSB_SYS>,
> + <&infracfg CLK_IFR_ICUSB>,
> + <&infracfg CLK_IFR_SSUSB_XHCI>;
> + clock-names = "sys_ck", "ref_ck", "mcu_ck",
> + "dma_ck", "xhci_ck";
> + status = "disabled";
> + };
> + };
> +
> + u3phy: phy@11cc0000 {
> + compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + #phy-cells = <1>;
> + ranges;
> +
> + u2port0: usb-phy@11cc0000 {
> + reg = <0 0x11cc0000 0 0x400>;
> + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> + <&topckgen CLK_TOP_USB20_48M_EN>;
> + clock-names = "ref", "da_ref";
> + #phy-cells = <1>;
> + };
> +
> + u2port1: usb-phy@11cc1000 {
> + reg = <0 0x11cc1000 0 0x400>;
> + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
> + <&topckgen CLK_TOP_USB20_48M_EN>;
> + clock-names = "ref", "da_ref";
> + #phy-cells = <1>;
> + };
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> + };
> +
> + system_clk: dummy13m {
> + compatible = "fixed-clock";
> + clock-frequency = <13000000>;
> + #clock-cells = <0>;
> + };
> +
> + systimer: timer@10017000 {
> + compatible = "mediatek,mt6795-systimer";
Why don't we use a compatible like
"mediatek,mt8365-systimer", "mediatek,mt6795-systimer";
We would need to add this to the binding description as well.
I leave it up to you, but I'd advise to start with a minimal working DT which
includes only the bindings that are already merged. Then we can take the new
devices like mtu3, xhci, spidev or i2c later once they are ready.
Regards,
Matthias
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support
2023-01-20 10:57 ` Matthias Brugger
@ 2023-01-23 16:10 ` Bernhard Rosenkränzer
-1 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-23 16:10 UTC (permalink / raw)
To: Matthias Brugger
Cc: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Hi,
On Fri, Jan 20, 2023 at 11:57 AM Matthias Brugger
<matthias.bgg@gmail.com> wrote:
> On 01/01/2023 23:01, Bernhard Rosenkränzer wrote:
> > + uart0: serial@11002000 {
> > + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
>
> Unfortunately we are missing this compatible in the binding description.
True, overlooked that one.
> > + ssusb: usb@11201000 {
> > + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
>
> Same here.
This is actually added by an earlier patch within this series (5/7),
but since it isn't used anywhere yet, might as well drop it for now,
"mediatek,mtu3" by itself works.
> > + usb_host: usb@11200000 {
> > + compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
>
> Same here.
Also added by an earlier patch within the series (6/7), and also not
used anywhere yet.
> > + systimer: timer@10017000 {
> > + compatible = "mediatek,mt6795-systimer";
>
> Why don't we use a compatible like
> "mediatek,mt8365-systimer", "mediatek,mt6795-systimer";
That was in an earlier revision and removed (because the binding
description wasn't merged yet). Can add it of course (but then
mediatek,mt8365-uart and friends should probably stay as well).
I'll post a new revision adding it back (along with the binding
description) and add the binding description for mt8365-uart as well
(getting it to the same place mediatek,mt8365-mtu3 and
mediatek,mt8365-xhci are now).
Let me know if you'd prefer a variant that drops mediatek,mt8365-uart,
mediatek,mt8365-mtu3, mediatek,mt8365-xhci and doesn't bring back
mediatek,mt8365-systimer -- either one works for me, the fallbacks are
sufficient to make it work.
ttyl
bero
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support
@ 2023-01-23 16:10 ` Bernhard Rosenkränzer
0 siblings, 0 replies; 30+ messages in thread
From: Bernhard Rosenkränzer @ 2023-01-23 16:10 UTC (permalink / raw)
To: Matthias Brugger
Cc: devicetree, linux-kernel, linux-gpio, linux-arm-kernel,
linux-mediatek, linux-usb, robh+dt, krzysztof.kozlowski+dt, tglx,
maz, lee, linus.walleij, chunfeng.yun, gregkh,
angelogioacchino.delregno, allen-kh.cheng, nfraprado, sean.wang,
zhiyong.tao
Hi,
On Fri, Jan 20, 2023 at 11:57 AM Matthias Brugger
<matthias.bgg@gmail.com> wrote:
> On 01/01/2023 23:01, Bernhard Rosenkränzer wrote:
> > + uart0: serial@11002000 {
> > + compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
>
> Unfortunately we are missing this compatible in the binding description.
True, overlooked that one.
> > + ssusb: usb@11201000 {
> > + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
>
> Same here.
This is actually added by an earlier patch within this series (5/7),
but since it isn't used anywhere yet, might as well drop it for now,
"mediatek,mtu3" by itself works.
> > + usb_host: usb@11200000 {
> > + compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
>
> Same here.
Also added by an earlier patch within the series (6/7), and also not
used anywhere yet.
> > + systimer: timer@10017000 {
> > + compatible = "mediatek,mt6795-systimer";
>
> Why don't we use a compatible like
> "mediatek,mt8365-systimer", "mediatek,mt6795-systimer";
That was in an earlier revision and removed (because the binding
description wasn't merged yet). Can add it of course (but then
mediatek,mt8365-uart and friends should probably stay as well).
I'll post a new revision adding it back (along with the binding
description) and add the binding description for mt8365-uart as well
(getting it to the same place mediatek,mt8365-mtu3 and
mediatek,mt8365-xhci are now).
Let me know if you'd prefer a variant that drops mediatek,mt8365-uart,
mediatek,mt8365-mtu3, mediatek,mt8365-xhci and doesn't bring back
mediatek,mt8365-systimer -- either one works for me, the fallbacks are
sufficient to make it work.
ttyl
bero
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 30+ messages in thread
end of thread, other threads:[~2023-01-23 16:33 UTC | newest]
Thread overview: 30+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-01 22:01 [PATCH v7 0/7] Add minimal MT8365 and MT8365-EVK support Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-01 22:01 ` [PATCH v7 1/7] dt-bindings: arm64: dts: mediatek: Add mt8365-evk board Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-01 22:01 ` [PATCH v7 2/7] dt-bindings: irq: mtk, sysirq: add support for mt8365 Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-01 22:01 ` [PATCH v7 3/7] dt-bindings: mfd: syscon: Add mt8365-syscfg Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-02 12:09 ` AngeloGioacchino Del Regno
2023-01-02 12:09 ` AngeloGioacchino Del Regno
2023-01-01 22:01 ` [PATCH v7 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-08 20:23 ` Rob Herring
2023-01-08 20:23 ` Rob Herring
2023-01-09 13:35 ` Linus Walleij
2023-01-09 13:35 ` Linus Walleij
2023-01-19 18:21 ` Matthias Brugger
2023-01-19 18:21 ` Matthias Brugger
2023-01-01 22:01 ` [PATCH v7 5/7] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-02 12:09 ` AngeloGioacchino Del Regno
2023-01-02 12:09 ` AngeloGioacchino Del Regno
2023-01-01 22:01 ` [PATCH v7 6/7] dt-bindings: usb: mediatek,mtk-xhci: " Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-01 22:01 ` [PATCH v7 7/7] arm64: dts: mediatek: Initial mt8365-evk support Bernhard Rosenkränzer
2023-01-01 22:01 ` Bernhard Rosenkränzer
2023-01-20 10:57 ` Matthias Brugger
2023-01-20 10:57 ` Matthias Brugger
2023-01-23 16:10 ` Bernhard Rosenkränzer
2023-01-23 16:10 ` Bernhard Rosenkränzer
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.