[PATCH 0/4] arm64: dts: ti: Enable misc peripherals

[PATCH 0/4] arm64: dts: ti: Enable misc peripherals

[Vignesh Raghavendra]

This series enables few additional peripherals such as DMA, ethernet,
PWMs, GPIOs etc  on AM62A SoC and AM62A7 SK EVM.

Vignesh Raghavendra (4):
  arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
  arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
  arm64: dts: ti: k3-am62a7-sk: Enable  ethernet port
  arm64: dts: ti: k3-am62a7-sk: Enable USB1 node

 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi  |  51 +++
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts   |  70 +++++
 3 files changed, 486 insertions(+)

-- 
2.39.0

[PATCH 0/4] arm64: dts: ti: Enable misc peripherals

[Vignesh Raghavendra]

This series enables few additional peripherals such as DMA, ethernet,
PWMs, GPIOs etc  on AM62A SoC and AM62A7 SK EVM.

Vignesh Raghavendra (4):
  arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
  arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
  arm64: dts: ti: k3-am62a7-sk: Enable  ethernet port
  arm64: dts: ti: k3-am62a7-sk: Enable USB1 node

 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi  |  51 +++
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts   |  70 +++++
 3 files changed, 486 insertions(+)

-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/4] arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals

[Vignesh Raghavendra]

Introduce DT nodes for MCU domain SPIs and GPIO modules.

Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi | 51 ++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
index 6d1e501b94ab..2bb813e784a2 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
@@ -36,4 +36,55 @@ mcu_i2c0: i2c@4900000 {
 		clock-names = "fck";
 		status = "disabled";
 	};
+
+	mcu_spi0: spi@4b00000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x04b00000 0x00 0x400>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 147 0>;
+		status = "disabled";
+	};
+
+	mcu_spi1: spi@4b10000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x04b10000 0x00 0x400>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 148 0>;
+		status = "disabled";
+	};
+
+	mcu_gpio_intr: interrupt-controller@4210000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x04210000 0x00 0x200>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <5>;
+		ti,interrupt-ranges = <0 104 4>;
+	};
+
+	mcu_gpio0: gpio@4201000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x04201000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&mcu_gpio_intr>;
+		interrupts = <30>, <31>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <24>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 79 0>;
+		clock-names = "gpio";
+		status = "disabled";
+	};
 };
-- 
2.39.0

[PATCH 1/4] arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals

[Vignesh Raghavendra]

Introduce DT nodes for MCU domain SPIs and GPIO modules.

Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi | 51 ++++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
index 6d1e501b94ab..2bb813e784a2 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
@@ -36,4 +36,55 @@ mcu_i2c0: i2c@4900000 {
 		clock-names = "fck";
 		status = "disabled";
 	};
+
+	mcu_spi0: spi@4b00000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x04b00000 0x00 0x400>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 147 0>;
+		status = "disabled";
+	};
+
+	mcu_spi1: spi@4b10000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x04b10000 0x00 0x400>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 148 0>;
+		status = "disabled";
+	};
+
+	mcu_gpio_intr: interrupt-controller@4210000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x04210000 0x00 0x200>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <5>;
+		ti,interrupt-ranges = <0 104 4>;
+	};
+
+	mcu_gpio0: gpio@4201000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x04201000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&mcu_gpio_intr>;
+		interrupts = <30>, <31>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <24>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 79 0>;
+		clock-names = "gpio";
+		status = "disabled";
+	};
 };
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/4] arm64: dts: ti: k3-am62a-main: Add more peripheral nodes

[Vignesh Raghavendra]

Add DT nodes for main domain SPI, PWM, DMA, CPSW (ethernet), mailbox,
spinlock, USB and CAN.

Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++
 1 file changed, 365 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
index bc4b50bcd177..393a1a40b68b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -48,6 +48,18 @@ main_conf: syscon@100000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00100000 0x20000>;
+
+		phy_gmii_sel: phy@4044 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4044 0x8>;
+			#phy-cells = <1>;
+		};
+
+		epwm_tbclk: clock-controller@4130 {
+			compatible = "ti,am62-epwm-tbclk", "syscon";
+			reg = <0x4130 0x4>;
+			#clock-cells = <1>;
+		};
 	};
 
 	dmss: bus@48000000 {
@@ -69,6 +81,67 @@ secure_proxy_main: mailbox@4d000000 {
 			interrupt-names = "rx_012";
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		inta_main_dmss: interrupt-controller@48000000 {
+			compatible = "ti,sci-inta";
+			reg = <0x00 0x48000000 0x00 0x100000>;
+			#interrupt-cells = <0>;
+			interrupt-controller;
+			interrupt-parent = <&gic500>;
+			msi-controller;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <28>;
+			ti,interrupt-ranges = <6 70 34>;
+			ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+		};
+
+		main_bcdma: dma-controller@485c0100 {
+			compatible = "ti,am64-dmss-bcdma";
+			reg = <0x00 0x485c0100 0x00 0x100>,
+			      <0x00 0x4c000000 0x00 0x20000>,
+			      <0x00 0x4a820000 0x00 0x20000>,
+			      <0x00 0x4aa40000 0x00 0x20000>,
+			      <0x00 0x4bc00000 0x00 0x100000>;
+			reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <3>;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <26>;
+			ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+			ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+			ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+		};
+
+		main_pktdma: dma-controller@485c0000 {
+			compatible = "ti,am64-dmss-pktdma";
+			reg = <0x00 0x485c0000 0x00 0x100>,
+			      <0x00 0x4a800000 0x00 0x20000>,
+			      <0x00 0x4aa00000 0x00 0x40000>,
+			      <0x00 0x4b800000 0x00 0x400000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <2>;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <30>;
+			ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+						<0x24>, /* CPSW_TX_CHAN */
+						<0x25>, /* SAUL_TX_0_CHAN */
+						<0x26>; /* SAUL_TX_1_CHAN */
+			ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+						<0x11>, /* RING_CPSW_TX_CHAN */
+						<0x12>, /* RING_SAUL_TX_0_CHAN */
+						<0x13>; /* RING_SAUL_TX_1_CHAN */
+			ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+						<0x2b>, /* CPSW_RX_CHAN */
+						<0x2d>, /* SAUL_RX_0_CHAN */
+						<0x2f>, /* SAUL_RX_1_CHAN */
+						<0x31>, /* SAUL_RX_2_CHAN */
+						<0x33>; /* SAUL_RX_3_CHAN */
+			ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+						<0x2c>, /* FLOW_CPSW_RX_CHAN */
+						<0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+						<0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
+		};
 	};
 
 	dmsc: system-controller@44043000 {
@@ -222,6 +295,39 @@ main_i2c3: i2c@20030000 {
 		status = "disabled";
 	};
 
+	main_spi0: spi@20100000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x20100000 0x00 0x400>;
+		interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 141 0>;
+		status = "disabled";
+	};
+
+	main_spi1: spi@20110000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20110000 0x00 0x400>;
+		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 142 0>;
+		status = "disabled";
+	};
+
+	main_spi2: spi@20120000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20120000 0x00 0x400>;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 143 0>;
+		status = "disabled";
+	};
+
 	main_gpio_intr: interrupt-controller@a00000 {
 		compatible = "ti,sci-intr";
 		reg = <0x00 0x00a00000 0x00 0x800>;
@@ -295,4 +401,263 @@ sdhci1: mmc@fa00000 {
 		no-1-8-v;
 		status = "disabled";
 	};
+
+	usbss0: dwc3-usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	fss: bus@fc00000 {
+		compatible = "simple-bus";
+		reg = <0x00 0x0fc00000 0x00 0x70000>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		status = "disabled";
+
+		ospi0: spi@fc40000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x0fc40000 0x00 0x100>,
+			      <0x05 0x00000000 0x01 0x00000000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 75 7>;
+			assigned-clocks = <&k3_clks 75 7>;
+			assigned-clock-parents = <&k3_clks 75 8>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	cpsw3g: ethernet@8000000 {
+		compatible = "ti,am642-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x0 0x8000000 0x0 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x0 0x0 0x0 0x8000000 0x0 0x200000>;
+		clocks = <&k3_clks 13 0>;
+		assigned-clocks = <&k3_clks 13 3>;
+		assigned-clock-parents = <&k3_clks 13 11>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+
+		dmas = <&main_pktdma 0xc600 15>,
+		       <&main_pktdma 0xc601 15>,
+		       <&main_pktdma 0xc602 15>,
+		       <&main_pktdma 0xc603 15>,
+		       <&main_pktdma 0xc604 15>,
+		       <&main_pktdma 0xc605 15>,
+		       <&main_pktdma 0xc606 15>,
+		       <&main_pktdma 0xc607 15>,
+		       <&main_pktdma 0x4600 15>;
+		dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+			    "tx7", "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				phys = <&phy_gmii_sel 1>;
+				mac-address = [00 00 00 00 00 00];
+				ti,syscon-efuse = <&wkup_conf 0x200>;
+			};
+
+			cpsw_port2: port@2 {
+				reg = <2>;
+				ti,mac-only;
+				label = "port2";
+				phys = <&phy_gmii_sel 2>;
+				mac-address = [00 00 00 00 00 00];
+			};
+		};
+
+		cpsw3g_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x0 0xf00 0x0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 13 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+
+		cpts@3d000 {
+			compatible = "ti,j721e-cpts";
+			reg = <0x0 0x3d000 0x0 0x400>;
+			clocks = <&k3_clks 13 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+
+	hwspinlock: spinlock@2a000000 {
+		compatible = "ti,am64-hwspinlock";
+		reg = <0x00 0x2a000000 0x00 0x1000>;
+		#hwlock-cells = <1>;
+	};
+
+	mailbox0_cluster0: mailbox@29000000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29000000 0x00 0x200>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster1: mailbox@29010000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29010000 0x00 0x200>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster2: mailbox@29020000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29020000 0x00 0x200>;
+		interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster3: mailbox@29030000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29030000 0x00 0x200>;
+		interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	main_mcan0: can@20701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20701000 0x00 0x200>,
+		      <0x00 0x20708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
+	};
+
+	epwm0: pwm@23000000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23000000 0x00 0x100>;
+		power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm1: pwm@23010000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23010000 0x00 0x100>;
+		power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm2: pwm@23020000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23020000 0x00 0x100>;
+		power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	ecap0: pwm@23100000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23100000 0x00 0x100>;
+		power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 51 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	ecap1: pwm@23110000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23110000 0x00 0x100>;
+		power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 52 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	ecap2: pwm@23120000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23120000 0x00 0x100>;
+		power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 53 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
 };
-- 
2.39.0

[PATCH 2/4] arm64: dts: ti: k3-am62a-main: Add more peripheral nodes

[Vignesh Raghavendra]

Add DT nodes for main domain SPI, PWM, DMA, CPSW (ethernet), mailbox,
spinlock, USB and CAN.

Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 365 ++++++++++++++++++++++
 1 file changed, 365 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
index bc4b50bcd177..393a1a40b68b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -48,6 +48,18 @@ main_conf: syscon@100000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00100000 0x20000>;
+
+		phy_gmii_sel: phy@4044 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4044 0x8>;
+			#phy-cells = <1>;
+		};
+
+		epwm_tbclk: clock-controller@4130 {
+			compatible = "ti,am62-epwm-tbclk", "syscon";
+			reg = <0x4130 0x4>;
+			#clock-cells = <1>;
+		};
 	};
 
 	dmss: bus@48000000 {
@@ -69,6 +81,67 @@ secure_proxy_main: mailbox@4d000000 {
 			interrupt-names = "rx_012";
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		inta_main_dmss: interrupt-controller@48000000 {
+			compatible = "ti,sci-inta";
+			reg = <0x00 0x48000000 0x00 0x100000>;
+			#interrupt-cells = <0>;
+			interrupt-controller;
+			interrupt-parent = <&gic500>;
+			msi-controller;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <28>;
+			ti,interrupt-ranges = <6 70 34>;
+			ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+		};
+
+		main_bcdma: dma-controller@485c0100 {
+			compatible = "ti,am64-dmss-bcdma";
+			reg = <0x00 0x485c0100 0x00 0x100>,
+			      <0x00 0x4c000000 0x00 0x20000>,
+			      <0x00 0x4a820000 0x00 0x20000>,
+			      <0x00 0x4aa40000 0x00 0x20000>,
+			      <0x00 0x4bc00000 0x00 0x100000>;
+			reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <3>;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <26>;
+			ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+			ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+			ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+		};
+
+		main_pktdma: dma-controller@485c0000 {
+			compatible = "ti,am64-dmss-pktdma";
+			reg = <0x00 0x485c0000 0x00 0x100>,
+			      <0x00 0x4a800000 0x00 0x20000>,
+			      <0x00 0x4aa00000 0x00 0x40000>,
+			      <0x00 0x4b800000 0x00 0x400000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <2>;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <30>;
+			ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+						<0x24>, /* CPSW_TX_CHAN */
+						<0x25>, /* SAUL_TX_0_CHAN */
+						<0x26>; /* SAUL_TX_1_CHAN */
+			ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+						<0x11>, /* RING_CPSW_TX_CHAN */
+						<0x12>, /* RING_SAUL_TX_0_CHAN */
+						<0x13>; /* RING_SAUL_TX_1_CHAN */
+			ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+						<0x2b>, /* CPSW_RX_CHAN */
+						<0x2d>, /* SAUL_RX_0_CHAN */
+						<0x2f>, /* SAUL_RX_1_CHAN */
+						<0x31>, /* SAUL_RX_2_CHAN */
+						<0x33>; /* SAUL_RX_3_CHAN */
+			ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+						<0x2c>, /* FLOW_CPSW_RX_CHAN */
+						<0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+						<0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
+		};
 	};
 
 	dmsc: system-controller@44043000 {
@@ -222,6 +295,39 @@ main_i2c3: i2c@20030000 {
 		status = "disabled";
 	};
 
+	main_spi0: spi@20100000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x20100000 0x00 0x400>;
+		interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 141 0>;
+		status = "disabled";
+	};
+
+	main_spi1: spi@20110000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20110000 0x00 0x400>;
+		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 142 0>;
+		status = "disabled";
+	};
+
+	main_spi2: spi@20120000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20120000 0x00 0x400>;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 143 0>;
+		status = "disabled";
+	};
+
 	main_gpio_intr: interrupt-controller@a00000 {
 		compatible = "ti,sci-intr";
 		reg = <0x00 0x00a00000 0x00 0x800>;
@@ -295,4 +401,263 @@ sdhci1: mmc@fa00000 {
 		no-1-8-v;
 		status = "disabled";
 	};
+
+	usbss0: dwc3-usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	fss: bus@fc00000 {
+		compatible = "simple-bus";
+		reg = <0x00 0x0fc00000 0x00 0x70000>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		status = "disabled";
+
+		ospi0: spi@fc40000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x0fc40000 0x00 0x100>,
+			      <0x05 0x00000000 0x01 0x00000000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 75 7>;
+			assigned-clocks = <&k3_clks 75 7>;
+			assigned-clock-parents = <&k3_clks 75 8>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	cpsw3g: ethernet@8000000 {
+		compatible = "ti,am642-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x0 0x8000000 0x0 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x0 0x0 0x0 0x8000000 0x0 0x200000>;
+		clocks = <&k3_clks 13 0>;
+		assigned-clocks = <&k3_clks 13 3>;
+		assigned-clock-parents = <&k3_clks 13 11>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+
+		dmas = <&main_pktdma 0xc600 15>,
+		       <&main_pktdma 0xc601 15>,
+		       <&main_pktdma 0xc602 15>,
+		       <&main_pktdma 0xc603 15>,
+		       <&main_pktdma 0xc604 15>,
+		       <&main_pktdma 0xc605 15>,
+		       <&main_pktdma 0xc606 15>,
+		       <&main_pktdma 0xc607 15>,
+		       <&main_pktdma 0x4600 15>;
+		dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+			    "tx7", "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				phys = <&phy_gmii_sel 1>;
+				mac-address = [00 00 00 00 00 00];
+				ti,syscon-efuse = <&wkup_conf 0x200>;
+			};
+
+			cpsw_port2: port@2 {
+				reg = <2>;
+				ti,mac-only;
+				label = "port2";
+				phys = <&phy_gmii_sel 2>;
+				mac-address = [00 00 00 00 00 00];
+			};
+		};
+
+		cpsw3g_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x0 0xf00 0x0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 13 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+
+		cpts@3d000 {
+			compatible = "ti,j721e-cpts";
+			reg = <0x0 0x3d000 0x0 0x400>;
+			clocks = <&k3_clks 13 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+
+	hwspinlock: spinlock@2a000000 {
+		compatible = "ti,am64-hwspinlock";
+		reg = <0x00 0x2a000000 0x00 0x1000>;
+		#hwlock-cells = <1>;
+	};
+
+	mailbox0_cluster0: mailbox@29000000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29000000 0x00 0x200>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster1: mailbox@29010000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29010000 0x00 0x200>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster2: mailbox@29020000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29020000 0x00 0x200>;
+		interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	mailbox0_cluster3: mailbox@29030000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29030000 0x00 0x200>;
+		interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	main_mcan0: can@20701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20701000 0x00 0x200>,
+		      <0x00 0x20708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
+	};
+
+	epwm0: pwm@23000000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23000000 0x00 0x100>;
+		power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm1: pwm@23010000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23010000 0x00 0x100>;
+		power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm2: pwm@23020000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23020000 0x00 0x100>;
+		power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	ecap0: pwm@23100000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23100000 0x00 0x100>;
+		power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 51 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	ecap1: pwm@23110000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23110000 0x00 0x100>;
+		power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 52 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	ecap2: pwm@23120000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23120000 0x00 0x100>;
+		power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 53 0>;
+		clock-names = "fck";
+		status = "disabled";
+	};
 };
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/4] arm64: dts: ti: k3-am62a7-sk: Enable ethernet port

[Vignesh Raghavendra]

AM62A7 SK has a DP83867 PHY on the board connected to first port of
CPSW, enable the same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 54 +++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 576dbce80ad8..bdc363fcbb4b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -9,6 +9,7 @@
 
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
 #include "k3-am62a7.dtsi"
 
 / {
@@ -158,6 +159,30 @@ usr_led_pins_default: usr-led-pins-default {
 			AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
 		>;
 	};
+
+	main_mdio1_pins_default: main-mdio1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
+			AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
+		>;
+	};
+
+	main_rgmii1_pins_default: main-rgmii1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x14c, PIN_INPUT, 0) /* (AB16) RGMII1_RD0 */
+			AM62AX_IOPAD(0x150, PIN_INPUT, 0) /* (V15) RGMII1_RD1 */
+			AM62AX_IOPAD(0x154, PIN_INPUT, 0) /* (W15) RGMII1_RD2 */
+			AM62AX_IOPAD(0x158, PIN_INPUT, 0) /* (V14) RGMII1_RD3 */
+			AM62AX_IOPAD(0x148, PIN_INPUT, 0) /* (AA16) RGMII1_RXC */
+			AM62AX_IOPAD(0x144, PIN_INPUT, 0) /* (AA15) RGMII1_RX_CTL */
+			AM62AX_IOPAD(0x134, PIN_INPUT, 0) /* (Y17) RGMII1_TD0 */
+			AM62AX_IOPAD(0x138, PIN_INPUT, 0) /* (V16) RGMII1_TD1 */
+			AM62AX_IOPAD(0x13c, PIN_INPUT, 0) /* (Y16) RGMII1_TD2 */
+			AM62AX_IOPAD(0x140, PIN_INPUT, 0) /* (AA17) RGMII1_TD3 */
+			AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
+			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
+		>;
+	};
 };
 
 &main_i2c0 {
@@ -221,3 +246,32 @@ &main_uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
 };
+
+&cpsw3g {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_rgmii1_pins_default>;
+};
+
+&cpsw_port1 {
+	status = "okay";
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&cpsw3g_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mdio1_pins_default>;
+
+	cpsw3g_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
-- 
2.39.0

[PATCH 3/4] arm64: dts: ti: k3-am62a7-sk: Enable ethernet port

[Vignesh Raghavendra]

AM62A7 SK has a DP83867 PHY on the board connected to first port of
CPSW, enable the same.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 54 +++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 576dbce80ad8..bdc363fcbb4b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -9,6 +9,7 @@
 
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
 #include "k3-am62a7.dtsi"
 
 / {
@@ -158,6 +159,30 @@ usr_led_pins_default: usr-led-pins-default {
 			AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
 		>;
 	};
+
+	main_mdio1_pins_default: main-mdio1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
+			AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
+		>;
+	};
+
+	main_rgmii1_pins_default: main-rgmii1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x14c, PIN_INPUT, 0) /* (AB16) RGMII1_RD0 */
+			AM62AX_IOPAD(0x150, PIN_INPUT, 0) /* (V15) RGMII1_RD1 */
+			AM62AX_IOPAD(0x154, PIN_INPUT, 0) /* (W15) RGMII1_RD2 */
+			AM62AX_IOPAD(0x158, PIN_INPUT, 0) /* (V14) RGMII1_RD3 */
+			AM62AX_IOPAD(0x148, PIN_INPUT, 0) /* (AA16) RGMII1_RXC */
+			AM62AX_IOPAD(0x144, PIN_INPUT, 0) /* (AA15) RGMII1_RX_CTL */
+			AM62AX_IOPAD(0x134, PIN_INPUT, 0) /* (Y17) RGMII1_TD0 */
+			AM62AX_IOPAD(0x138, PIN_INPUT, 0) /* (V16) RGMII1_TD1 */
+			AM62AX_IOPAD(0x13c, PIN_INPUT, 0) /* (Y16) RGMII1_TD2 */
+			AM62AX_IOPAD(0x140, PIN_INPUT, 0) /* (AA17) RGMII1_TD3 */
+			AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
+			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
+		>;
+	};
 };
 
 &main_i2c0 {
@@ -221,3 +246,32 @@ &main_uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
 };
+
+&cpsw3g {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_rgmii1_pins_default>;
+};
+
+&cpsw_port1 {
+	status = "okay";
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&cpsw3g_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mdio1_pins_default>;
+
+	cpsw3g_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/4] arm64: dts: ti: k3-am62a7-sk: Enable USB1 node

[Vignesh Raghavendra]

Enable USB1 host port on AM62A7 SK.

Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index bdc363fcbb4b..5c9012141ee2 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -160,6 +160,12 @@ AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
 		>;
 	};
 
+	main_usb1_pins_default: main-usb1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+		>;
+	};
+
 	main_mdio1_pins_default: main-mdio1-pins-default {
 		pinctrl-single,pins = <
 			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
@@ -247,6 +253,16 @@ &main_uart0 {
 	pinctrl-0 = <&main_uart0_pins_default>;
 };
 
+&usbss1 {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+};
+
 &cpsw3g {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.39.0

[PATCH 4/4] arm64: dts: ti: k3-am62a7-sk: Enable USB1 node

[Vignesh Raghavendra]

Enable USB1 host port on AM62A7 SK.

Co-developed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index bdc363fcbb4b..5c9012141ee2 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -160,6 +160,12 @@ AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
 		>;
 	};
 
+	main_usb1_pins_default: main-usb1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
+		>;
+	};
+
 	main_mdio1_pins_default: main-mdio1-pins-default {
 		pinctrl-single,pins = <
 			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
@@ -247,6 +253,16 @@ &main_uart0 {
 	pinctrl-0 = <&main_uart0_pins_default>;
 };
 
+&usbss1 {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+};
+
 &cpsw3g {
 	status = "okay";
 	pinctrl-names = "default";
-- 
2.39.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/4] arm64: dts: ti: k3-am62a7-sk: Enable USB1 node

[Dhruva Gole]

On 03/01/23 09:51, Vignesh Raghavendra wrote:
> Enable USB1 host port on AM62A7 SK.
> 
> Co-developed-by: Bryan Brattlof <bb@ti.com>
> Signed-off-by: Bryan Brattlof <bb@ti.com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---

For the series,

Acked-by: Dhruva Gole <d-gole@ti.com>

>   arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 16 ++++++++++++++++
>   1 file changed, 16 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index bdc363fcbb4b..5c9012141ee2 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -160,6 +160,12 @@ AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
>   		>;
>   	};
>   
> +	main_usb1_pins_default: main-usb1-pins-default {
> +		pinctrl-single,pins = <
> +			AM62AX_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
> +		>;
> +	};
> +
>   	main_mdio1_pins_default: main-mdio1-pins-default {
>   		pinctrl-single,pins = <
>   			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
> @@ -247,6 +253,16 @@ &main_uart0 {
>   	pinctrl-0 = <&main_uart0_pins_default>;
>   };
>   
> +&usbss1 {
> +	status = "okay";
> +};
> +
> +&usb1 {
> +	dr_mode = "host";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_usb1_pins_default>;
> +};
> +
>   &cpsw3g {
>   	status = "okay";
>   	pinctrl-names = "default";

-- 
Thanks and Regards,
Dhruva Gole

Re: [PATCH 4/4] arm64: dts: ti: k3-am62a7-sk: Enable USB1 node

[Dhruva Gole]

On 03/01/23 09:51, Vignesh Raghavendra wrote:
> Enable USB1 host port on AM62A7 SK.
> 
> Co-developed-by: Bryan Brattlof <bb@ti.com>
> Signed-off-by: Bryan Brattlof <bb@ti.com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---

For the series,

Acked-by: Dhruva Gole <d-gole@ti.com>

>   arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 16 ++++++++++++++++
>   1 file changed, 16 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index bdc363fcbb4b..5c9012141ee2 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -160,6 +160,12 @@ AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
>   		>;
>   	};
>   
> +	main_usb1_pins_default: main-usb1-pins-default {
> +		pinctrl-single,pins = <
> +			AM62AX_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */
> +		>;
> +	};
> +
>   	main_mdio1_pins_default: main-mdio1-pins-default {
>   		pinctrl-single,pins = <
>   			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
> @@ -247,6 +253,16 @@ &main_uart0 {
>   	pinctrl-0 = <&main_uart0_pins_default>;
>   };
>   
> +&usbss1 {
> +	status = "okay";
> +};
> +
> +&usb1 {
> +	dr_mode = "host";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_usb1_pins_default>;
> +};
> +
>   &cpsw3g {
>   	status = "okay";
>   	pinctrl-names = "default";

-- 
Thanks and Regards,
Dhruva Gole

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/4] arm64: dts: ti: Enable misc peripherals

[Vignesh Raghavendra]

Hi Vignesh Raghavendra,

On Tue, 3 Jan 2023 09:51:06 +0530, Vignesh Raghavendra wrote:
> This series enables few additional peripherals such as DMA, ethernet,
> PWMs, GPIOs etc  on AM62A SoC and AM62A7 SK EVM.
> 
> Vignesh Raghavendra (4):
>   arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
>   arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
>   arm64: dts: ti: k3-am62a7-sk: Enable  ethernet port
>   arm64: dts: ti: k3-am62a7-sk: Enable USB1 node
> 
> [...]

I have applied the following to branch ti-k3-next on [1].
Thank you!

[1/4] arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
      commit: eaee246b5e7b212069af40d6eb419158fac1325d
[2/4] arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
      commit: 3dad70def7ff086152a383a60dd6ca4ea8a9b10d
[3/4] arm64: dts: ti: k3-am62a7-sk: Enable ethernet port
      commit: a9da45c013f232e72a1899ad2bf3760a187c2ab8
[4/4] arm64: dts: ti: k3-am62a7-sk: Enable USB1 node
      commit: 42057a6ba99f42bd41a60e1f3ed111296e8bf099

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh

Re: [PATCH 0/4] arm64: dts: ti: Enable misc peripherals

[Vignesh Raghavendra]

Hi Vignesh Raghavendra,

On Tue, 3 Jan 2023 09:51:06 +0530, Vignesh Raghavendra wrote:
> This series enables few additional peripherals such as DMA, ethernet,
> PWMs, GPIOs etc  on AM62A SoC and AM62A7 SK EVM.
> 
> Vignesh Raghavendra (4):
>   arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
>   arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
>   arm64: dts: ti: k3-am62a7-sk: Enable  ethernet port
>   arm64: dts: ti: k3-am62a7-sk: Enable USB1 node
> 
> [...]

I have applied the following to branch ti-k3-next on [1].
Thank you!

[1/4] arm64: dts: ti: k3-am62a-mcu: Add MCU domain peripherals
      commit: eaee246b5e7b212069af40d6eb419158fac1325d
[2/4] arm64: dts: ti: k3-am62a-main: Add more peripheral nodes
      commit: 3dad70def7ff086152a383a60dd6ca4ea8a9b10d
[3/4] arm64: dts: ti: k3-am62a7-sk: Enable ethernet port
      commit: a9da45c013f232e72a1899ad2bf3760a187c2ab8
[4/4] arm64: dts: ti: k3-am62a7-sk: Enable USB1 node
      commit: 42057a6ba99f42bd41a60e1f3ed111296e8bf099

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel