[PATCH v3 0/8] phy: qualcomm: Add PCIe support for SM8550

[PATCH v3 0/8] phy: qualcomm: Add PCIe support for SM8550

[Abel Vesa]

This patchset relies on the following patchset:
https://lore.kernel.org/all/20230117224148.1914627-1-abel.vesa@linaro.org/

The v2 of this patchset is:
https://lore.kernel.org/all/20230118003834.2330028-1-abel.vesa@linaro.org/

Changes since v2:
 * added back the binding compatible update patch

Abel Vesa (8):
  dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550
  phy: qcom-qmp: pcs: Add v6 register offsets
  phy: qcom-qmp: pcs: Add v6.20 register offsets
  phy: qcom-qmp: pcs-pcie: Add v6 register offsets
  phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets
  phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets
  phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets
  phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

 .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   2 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 371 ++++++++++++++++++
 .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h   |  15 +
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h    |  23 ++
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h    |  16 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h |  18 +
 .../phy-qcom-qmp-qserdes-ln-shrd-v6.h         |  32 ++
 .../phy-qcom-qmp-qserdes-txrx-v6_20.h         |  45 +++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |   6 +
 9 files changed, 528 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 0/8] phy: qualcomm: Add PCIe support for SM8550

[Abel Vesa]

This patchset relies on the following patchset:
https://lore.kernel.org/all/20230117224148.1914627-1-abel.vesa@linaro.org/

The v2 of this patchset is:
https://lore.kernel.org/all/20230118003834.2330028-1-abel.vesa@linaro.org/

Changes since v2:
 * added back the binding compatible update patch

Abel Vesa (8):
  dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550
  phy: qcom-qmp: pcs: Add v6 register offsets
  phy: qcom-qmp: pcs: Add v6.20 register offsets
  phy: qcom-qmp: pcs-pcie: Add v6 register offsets
  phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets
  phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets
  phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets
  phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

 .../phy/qcom,sc8280xp-qmp-pcie-phy.yaml       |   2 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 371 ++++++++++++++++++
 .../phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h   |  15 +
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h    |  23 ++
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h    |  16 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h |  18 +
 .../phy-qcom-qmp-qserdes-ln-shrd-v6.h         |  32 ++
 .../phy-qcom-qmp-qserdes-txrx-v6_20.h         |  45 +++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |   6 +
 9 files changed, 528 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

-- 
2.34.1

[PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Abel Vesa]

Document the QMP PCIe PHY compatible for SM8550.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
index 8a85318d9c92..65f26cfff3fb 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
@@ -20,6 +20,8 @@ properties:
       - qcom,sc8280xp-qmp-gen3x2-pcie-phy
       - qcom,sc8280xp-qmp-gen3x4-pcie-phy
       - qcom,sm8350-qmp-gen3x1-pcie-phy
+      - qcom,sm8550-qmp-gen3x2-pcie-phy
+      - qcom,sm8550-qmp-gen4x2-pcie-phy
 
   reg:
     minItems: 1
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Abel Vesa]

Document the QMP PCIe PHY compatible for SM8550.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
index 8a85318d9c92..65f26cfff3fb 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
@@ -20,6 +20,8 @@ properties:
       - qcom,sc8280xp-qmp-gen3x2-pcie-phy
       - qcom,sc8280xp-qmp-gen3x4-pcie-phy
       - qcom,sm8350-qmp-gen3x1-pcie-phy
+      - qcom,sm8550-qmp-gen3x2-pcie-phy
+      - qcom,sm8550-qmp-gen4x2-pcie-phy
 
   reg:
     minItems: 1
-- 
2.34.1

[PATCH v3 2/8] phy: qcom-qmp: pcs: Add v6 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS offsets in a dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h | 16 ++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h        |  2 ++
 2 files changed, 18 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h
new file mode 100644
index 000000000000..18c4a3abe590
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_V6_H_
+#define QCOM_PHY_QMP_PCS_V6_H_
+
+/* Only for QMP V6 PHY - USB/PCIe PCS registers */
+#define QPHY_V6_PCS_REFGEN_REQ_CONFIG1		0xdc
+#define QPHY_V6_PCS_RX_SIGDET_LVL		0x188
+#define QPHY_V6_PCS_RATE_SLEW_CNTRL1		0x198
+#define QPHY_V6_PCS_EQ_CONFIG2			0x1e0
+#define QPHY_V6_PCS_PCS_TX_RX_CONFIG		0x1d0
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index a63a691b8372..80e3b5c860b6 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -38,6 +38,8 @@
 
 #include "phy-qcom-qmp-pcs-v5_20.h"
 
+#include "phy-qcom-qmp-pcs-v6.h"
+
 /* Only for QMP V3 & V4 PHY - DP COM registers */
 #define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
 #define QPHY_V3_DP_COM_SW_RESET				0x04
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 2/8] phy: qcom-qmp: pcs: Add v6 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS offsets in a dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h | 16 ++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h        |  2 ++
 2 files changed, 18 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h
new file mode 100644
index 000000000000..18c4a3abe590
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_V6_H_
+#define QCOM_PHY_QMP_PCS_V6_H_
+
+/* Only for QMP V6 PHY - USB/PCIe PCS registers */
+#define QPHY_V6_PCS_REFGEN_REQ_CONFIG1		0xdc
+#define QPHY_V6_PCS_RX_SIGDET_LVL		0x188
+#define QPHY_V6_PCS_RATE_SLEW_CNTRL1		0x198
+#define QPHY_V6_PCS_EQ_CONFIG2			0x1e0
+#define QPHY_V6_PCS_PCS_TX_RX_CONFIG		0x1d0
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index a63a691b8372..80e3b5c860b6 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -38,6 +38,8 @@
 
 #include "phy-qcom-qmp-pcs-v5_20.h"
 
+#include "phy-qcom-qmp-pcs-v6.h"
+
 /* Only for QMP V3 & V4 PHY - DP COM registers */
 #define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
 #define QPHY_V3_DP_COM_SW_RESET				0x04
-- 
2.34.1

[PATCH v3 3/8] phy: qcom-qmp: pcs: Add v6.20 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new PCS offsets in a dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h | 18 ++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  2 ++
 2 files changed, 20 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h
new file mode 100644
index 000000000000..9c3f1e4950e6
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_V6_20_H_
+#define QCOM_PHY_QMP_PCS_V6_20_H_
+
+/* Only for QMP V6_20 PHY - USB/PCIe PCS registers */
+#define QPHY_V6_20_PCS_G3S2_PRE_GAIN			0x178
+#define QPHY_V6_20_PCS_RX_SIGDET_LVL			0x190
+#define QPHY_V6_20_PCS_COM_ELECIDLE_DLY_SEL		0x1b8
+#define QPHY_V6_20_PCS_TX_RX_CONFIG1			0x1dc
+#define QPHY_V6_20_PCS_TX_RX_CONFIG2			0x1e0
+#define QPHY_V6_20_PCS_EQ_CONFIG4			0x1f8
+#define QPHY_V6_20_PCS_EQ_CONFIG5			0x1fc
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 80e3b5c860b6..760de4c76e5b 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -40,6 +40,8 @@
 
 #include "phy-qcom-qmp-pcs-v6.h"
 
+#include "phy-qcom-qmp-pcs-v6_20.h"
+
 /* Only for QMP V3 & V4 PHY - DP COM registers */
 #define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
 #define QPHY_V3_DP_COM_SW_RESET				0x04
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 3/8] phy: qcom-qmp: pcs: Add v6.20 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new PCS offsets in a dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h | 18 ++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  2 ++
 2 files changed, 20 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h
new file mode 100644
index 000000000000..9c3f1e4950e6
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_V6_20_H_
+#define QCOM_PHY_QMP_PCS_V6_20_H_
+
+/* Only for QMP V6_20 PHY - USB/PCIe PCS registers */
+#define QPHY_V6_20_PCS_G3S2_PRE_GAIN			0x178
+#define QPHY_V6_20_PCS_RX_SIGDET_LVL			0x190
+#define QPHY_V6_20_PCS_COM_ELECIDLE_DLY_SEL		0x1b8
+#define QPHY_V6_20_PCS_TX_RX_CONFIG1			0x1dc
+#define QPHY_V6_20_PCS_TX_RX_CONFIG2			0x1e0
+#define QPHY_V6_20_PCS_EQ_CONFIG4			0x1f8
+#define QPHY_V6_20_PCS_EQ_CONFIG5			0x1fc
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 80e3b5c860b6..760de4c76e5b 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -40,6 +40,8 @@
 
 #include "phy-qcom-qmp-pcs-v6.h"
 
+#include "phy-qcom-qmp-pcs-v6_20.h"
+
 /* Only for QMP V3 & V4 PHY - DP COM registers */
 #define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
 #define QPHY_V3_DP_COM_SW_RESET				0x04
-- 
2.34.1

[PATCH v3 4/8] phy: qcom-qmp: pcs-pcie: Add v6 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS PCIE specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c        |  1 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h | 15 +++++++++++++++
 2 files changed, 16 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index 21727e90fad1..d4ca38f31e3f 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -29,6 +29,7 @@
 #include "phy-qcom-qmp-pcs-pcie-v4_20.h"
 #include "phy-qcom-qmp-pcs-pcie-v5.h"
 #include "phy-qcom-qmp-pcs-pcie-v5_20.h"
+#include "phy-qcom-qmp-pcs-pcie-v6.h"
 #include "phy-qcom-qmp-pcie-qhp.h"
 
 /* QPHY_SW_RESET bit */
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h
new file mode 100644
index 000000000000..91e70002eb47
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_H_
+#define QCOM_PHY_QMP_PCS_PCIE_V6_H_
+
+/* Only for QMP V6 PHY - PCIE have different offsets than V5 */
+#define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2	0x0c
+#define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4	0x14
+#define QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE	0x20
+#define QPHY_PCIE_V6_PCS_PCIE_OSC_DTCT_ACTIONS		0x94
+
+#endif
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 4/8] phy: qcom-qmp: pcs-pcie: Add v6 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS PCIE specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c        |  1 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h | 15 +++++++++++++++
 2 files changed, 16 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index 21727e90fad1..d4ca38f31e3f 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -29,6 +29,7 @@
 #include "phy-qcom-qmp-pcs-pcie-v4_20.h"
 #include "phy-qcom-qmp-pcs-pcie-v5.h"
 #include "phy-qcom-qmp-pcs-pcie-v5_20.h"
+#include "phy-qcom-qmp-pcs-pcie-v6.h"
 #include "phy-qcom-qmp-pcie-qhp.h"
 
 /* QPHY_SW_RESET bit */
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h
new file mode 100644
index 000000000000..91e70002eb47
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_H_
+#define QCOM_PHY_QMP_PCS_PCIE_V6_H_
+
+/* Only for QMP V6 PHY - PCIE have different offsets than V5 */
+#define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2	0x0c
+#define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4	0x14
+#define QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE	0x20
+#define QPHY_PCIE_V6_PCS_PCIE_OSC_DTCT_ACTIONS		0x94
+
+#endif
-- 
2.34.1

[PATCH v3 5/8] phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new PCS PCIE specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      |  1 +
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h    | 23 +++++++++++++++++++
 2 files changed, 24 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index d4ca38f31e3f..bffb9e138715 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -30,6 +30,7 @@
 #include "phy-qcom-qmp-pcs-pcie-v5.h"
 #include "phy-qcom-qmp-pcs-pcie-v5_20.h"
 #include "phy-qcom-qmp-pcs-pcie-v6.h"
+#include "phy-qcom-qmp-pcs-pcie-v6_20.h"
 #include "phy-qcom-qmp-pcie-qhp.h"
 
 /* QPHY_SW_RESET bit */
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h
new file mode 100644
index 000000000000..e3eb08776339
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_20_H_
+#define QCOM_PHY_QMP_PCS_PCIE_V6_20_H_
+
+/* Only for QMP V6_20 PHY - PCIE have different offsets than V5 */
+#define QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2		0x00c
+#define QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG		0x018
+#define QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE	0x01c
+#define QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS		0x090
+#define QPHY_PCIE_V6_20_PCS_EQ_CONFIG1			0x0a0
+#define QPHY_PCIE_V6_20_PCS_EQ_CONFIG5			0x108
+#define QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN			0x15c
+#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1	0x17c
+#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3	0x184
+#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5	0x18c
+#define QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5		0x1ac
+#define QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5		0x1c0
+
+#endif
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 5/8] phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new PCS PCIE specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      |  1 +
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h    | 23 +++++++++++++++++++
 2 files changed, 24 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index d4ca38f31e3f..bffb9e138715 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -30,6 +30,7 @@
 #include "phy-qcom-qmp-pcs-pcie-v5.h"
 #include "phy-qcom-qmp-pcs-pcie-v5_20.h"
 #include "phy-qcom-qmp-pcs-pcie-v6.h"
+#include "phy-qcom-qmp-pcs-pcie-v6_20.h"
 #include "phy-qcom-qmp-pcie-qhp.h"
 
 /* QPHY_SW_RESET bit */
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h
new file mode 100644
index 000000000000..e3eb08776339
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_20_H_
+#define QCOM_PHY_QMP_PCS_PCIE_V6_20_H_
+
+/* Only for QMP V6_20 PHY - PCIE have different offsets than V5 */
+#define QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2		0x00c
+#define QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG		0x018
+#define QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE	0x01c
+#define QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS		0x090
+#define QPHY_PCIE_V6_20_PCS_EQ_CONFIG1			0x0a0
+#define QPHY_PCIE_V6_20_PCS_EQ_CONFIG5			0x108
+#define QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN			0x15c
+#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1	0x17c
+#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3	0x184
+#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5	0x18c
+#define QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5		0x1ac
+#define QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5		0x1c0
+
+#endif
-- 
2.34.1

[PATCH v3 6/8] phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new qserdes TX RX PCIE specific offsets in a
dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 .../phy-qcom-qmp-qserdes-txrx-v6_20.h         | 45 +++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  1 +
 2 files changed, 46 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h
new file mode 100644
index 000000000000..5385a8b60970
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_QSERDES_TXRX_PCIE_V6_20_H_
+#define QCOM_PHY_QMP_QSERDES_TXRX_PCIE_V6_20_H_
+
+#define QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX		0x30
+#define QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX		0x34
+#define QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN			0xac
+#define QSERDES_V6_20_TX_LANE_MODE_1				0x78
+#define QSERDES_V6_20_TX_LANE_MODE_2				0x7c
+#define QSERDES_V6_20_TX_LANE_MODE_3				0x80
+
+#define QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2			0x08
+#define QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3			0x0c
+#define QSERDES_V6_20_RX_UCDR_PI_CONTROLS			0x20
+#define QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3		0x34
+#define QSERDES_V6_20_RX_IVCM_CAL_CTRL2				0x9c
+#define QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET			0xa0
+#define QSERDES_V6_20_RX_DFE_3					0xb4
+#define QSERDES_V6_20_RX_VGA_CAL_MAN_VAL			0xe8
+#define QSERDES_V6_20_RX_GM_CAL					0x10c
+#define QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4			0x120
+#define QSERDES_V6_20_RX_SIGDET_ENABLES				0x148
+#define QSERDES_V6_20_RX_PHPRE_CTRL				0x188
+#define QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET		0x194
+#define QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32		0x1dc
+#define QSERDES_V6_20_RX_MODE_RATE2_B0				0x1f4
+#define QSERDES_V6_20_RX_MODE_RATE2_B1				0x1f8
+#define QSERDES_V6_20_RX_MODE_RATE2_B2				0x1fc
+#define QSERDES_V6_20_RX_MODE_RATE2_B3				0x200
+#define QSERDES_V6_20_RX_MODE_RATE2_B4				0x204
+#define QSERDES_V6_20_RX_MODE_RATE2_B5				0x208
+#define QSERDES_V6_20_RX_MODE_RATE2_B6				0x20c
+#define QSERDES_V6_20_RX_MODE_RATE3_B0				0x210
+#define QSERDES_V6_20_RX_MODE_RATE3_B1				0x214
+#define QSERDES_V6_20_RX_MODE_RATE3_B2				0x218
+#define QSERDES_V6_20_RX_MODE_RATE3_B3				0x21c
+#define QSERDES_V6_20_RX_MODE_RATE3_B4				0x220
+#define QSERDES_V6_20_RX_MODE_RATE3_B5				0x224
+#define QSERDES_V6_20_RX_MODE_RATE3_B6				0x228
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 760de4c76e5b..e5974e6caf51 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -23,6 +23,7 @@
 
 #include "phy-qcom-qmp-qserdes-com-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-v6.h"
+#include "phy-qcom-qmp-qserdes-txrx-v6_20.h"
 
 #include "phy-qcom-qmp-qserdes-pll.h"
 
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 6/8] phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new qserdes TX RX PCIE specific offsets in a
dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 .../phy-qcom-qmp-qserdes-txrx-v6_20.h         | 45 +++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  1 +
 2 files changed, 46 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h
new file mode 100644
index 000000000000..5385a8b60970
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_QSERDES_TXRX_PCIE_V6_20_H_
+#define QCOM_PHY_QMP_QSERDES_TXRX_PCIE_V6_20_H_
+
+#define QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX		0x30
+#define QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX		0x34
+#define QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN			0xac
+#define QSERDES_V6_20_TX_LANE_MODE_1				0x78
+#define QSERDES_V6_20_TX_LANE_MODE_2				0x7c
+#define QSERDES_V6_20_TX_LANE_MODE_3				0x80
+
+#define QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2			0x08
+#define QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3			0x0c
+#define QSERDES_V6_20_RX_UCDR_PI_CONTROLS			0x20
+#define QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3		0x34
+#define QSERDES_V6_20_RX_IVCM_CAL_CTRL2				0x9c
+#define QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET			0xa0
+#define QSERDES_V6_20_RX_DFE_3					0xb4
+#define QSERDES_V6_20_RX_VGA_CAL_MAN_VAL			0xe8
+#define QSERDES_V6_20_RX_GM_CAL					0x10c
+#define QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4			0x120
+#define QSERDES_V6_20_RX_SIGDET_ENABLES				0x148
+#define QSERDES_V6_20_RX_PHPRE_CTRL				0x188
+#define QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET		0x194
+#define QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32		0x1dc
+#define QSERDES_V6_20_RX_MODE_RATE2_B0				0x1f4
+#define QSERDES_V6_20_RX_MODE_RATE2_B1				0x1f8
+#define QSERDES_V6_20_RX_MODE_RATE2_B2				0x1fc
+#define QSERDES_V6_20_RX_MODE_RATE2_B3				0x200
+#define QSERDES_V6_20_RX_MODE_RATE2_B4				0x204
+#define QSERDES_V6_20_RX_MODE_RATE2_B5				0x208
+#define QSERDES_V6_20_RX_MODE_RATE2_B6				0x20c
+#define QSERDES_V6_20_RX_MODE_RATE3_B0				0x210
+#define QSERDES_V6_20_RX_MODE_RATE3_B1				0x214
+#define QSERDES_V6_20_RX_MODE_RATE3_B2				0x218
+#define QSERDES_V6_20_RX_MODE_RATE3_B3				0x21c
+#define QSERDES_V6_20_RX_MODE_RATE3_B4				0x220
+#define QSERDES_V6_20_RX_MODE_RATE3_B5				0x224
+#define QSERDES_V6_20_RX_MODE_RATE3_B6				0x228
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 760de4c76e5b..e5974e6caf51 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -23,6 +23,7 @@
 
 #include "phy-qcom-qmp-qserdes-com-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-v6.h"
+#include "phy-qcom-qmp-qserdes-txrx-v6_20.h"
 
 #include "phy-qcom-qmp-qserdes-pll.h"
 
-- 
2.34.1

[PATCH v3 7/8] phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new lane shared PCIE specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 .../phy-qcom-qmp-qserdes-ln-shrd-v6.h         | 32 +++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  1 +
 2 files changed, 33 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h
new file mode 100644
index 000000000000..86d7d796d5d7
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_QSERDES_LN_SHRD_V6_H_
+#define QCOM_PHY_QMP_QSERDES_LN_SHRD_V6_H_
+
+#define QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL			0xa0
+#define QSERDES_V6_LN_SHRD_RX_Q_EN_RATES			0xb0
+#define QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1			0xb4
+#define QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1		0xc4
+#define QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2		0xc8
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0			0xd4
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1			0xd8
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2			0xdc
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3			0xe0
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4			0xe4
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5			0xe8
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6			0xec
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210	0xf0
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3		0xf4
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210	0xf8
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3		0xfc
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210	0x100
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3		0x104
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3		0x10c
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3		0x114
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3		0x11c
+#define QSERDES_V6_LN_SHRD_RX_SUMMER_CAL_SPD_MODE		0x128
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index e5974e6caf51..148663ee713a 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -24,6 +24,7 @@
 #include "phy-qcom-qmp-qserdes-com-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-v6_20.h"
+#include "phy-qcom-qmp-qserdes-ln-shrd-v6.h"
 
 #include "phy-qcom-qmp-qserdes-pll.h"
 
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 7/8] phy: qcom-qmp: qserdes-lane-shared: Add v6 register offsets

[Abel Vesa]

The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new lane shared PCIE specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 .../phy-qcom-qmp-qserdes-ln-shrd-v6.h         | 32 +++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  1 +
 2 files changed, 33 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h
new file mode 100644
index 000000000000..86d7d796d5d7
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-ln-shrd-v6.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_QSERDES_LN_SHRD_V6_H_
+#define QCOM_PHY_QMP_QSERDES_LN_SHRD_V6_H_
+
+#define QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL			0xa0
+#define QSERDES_V6_LN_SHRD_RX_Q_EN_RATES			0xb0
+#define QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1			0xb4
+#define QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1		0xc4
+#define QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2		0xc8
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0			0xd4
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1			0xd8
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2			0xdc
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3			0xe0
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4			0xe4
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5			0xe8
+#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6			0xec
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210	0xf0
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3		0xf4
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210	0xf8
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3		0xfc
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210	0x100
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3		0x104
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3		0x10c
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3		0x114
+#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3		0x11c
+#define QSERDES_V6_LN_SHRD_RX_SUMMER_CAL_SPD_MODE		0x128
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index e5974e6caf51..148663ee713a 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -24,6 +24,7 @@
 #include "phy-qcom-qmp-qserdes-com-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-v6_20.h"
+#include "phy-qcom-qmp-qserdes-ln-shrd-v6.h"
 
 #include "phy-qcom-qmp-qserdes-pll.h"
 
-- 
2.34.1

[PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Abel Vesa]

Add the SM8550 both g4 and g3 configurations. In addition, there is a
new "lane shared" table that needs to be configured for g4, along with
the No-CSR list of resets.

Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
 1 file changed, 369 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index bffb9e138715..6f82604bd430 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
 	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
 };
 
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x93),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x42),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_ADDITIONAL_MISC_3, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_4, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_PI_QEC_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x18),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_GM_CAL, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH2, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH3, 0xb7),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH4, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_LOW, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH2, 0x9c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH3, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH4, 0x89),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH, 0x94),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH2, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH3, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH4, 0x89),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_TX_ADAPT_POST_THRESH, 0xf0),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_FO_GAIN, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SO_GAIN, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SB2_THRESH1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_VGA_CAL_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_SIDGET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_IDAC_TSETTLE_LOW, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_SIGDET_CAL_TRIM, 0x08),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_REFGEN_REQ_CONFIG1, 0x05),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_RX_SIGDET_LVL, 0x77),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_RATE_SLEW_CNTRL1, 0x0b),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_EQ_CONFIG2, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_PCS_TX_RX_CONFIG, 0x8c),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_OSC_DTCT_ACTIONS, 0x00),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x26),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x68),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_POST_DIV_MUX, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x46),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MISC_1, 0x88),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MODE, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_VCO_DC_LEVEL_CTRL, 0x0f),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_serdes_ln_shrd_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_Q_EN_RATES, 0xe),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3, 0x9a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5, 0xb6),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6, 0x64),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX, 0x1d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_3, 0x51),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN, 0x34),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_PI_CONTROLS, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_CAL_CTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET, 0x7c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_3, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_GM_CAL, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_SIGDET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_PHPRE_CTRL, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B1, 0xb3),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B2, 0x58),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B3, 0x9a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B4, 0x26),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B5, 0xb6),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B6, 0xee),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B0, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B1, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B2, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B3, 0xdf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B4, 0x78),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B5, 0x76),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B6, 0xff),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_G3S2_PRE_GAIN, 0x2e),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_COM_ELECIDLE_DLY_SEL, 0x25),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG4, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG5, 0x22),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG1, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG2, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE, 0xc1),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG1, 0x16),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG5, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN, 0x2e),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3, 0x28),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG, 0xc0),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5, 0xf2),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5, 0xf2),
+};
+
 struct qmp_pcie_offsets {
 	u16 serdes;
 	u16 pcs;
@@ -1514,11 +1742,14 @@ struct qmp_pcie_offsets {
 	u16 rx;
 	u16 tx2;
 	u16 rx2;
+	u16 ln_shrd;
 };
 
 struct qmp_phy_cfg_tbls {
 	const struct qmp_phy_init_tbl *serdes;
 	int serdes_num;
+	const struct qmp_phy_init_tbl *ln_shrd_serdes;
+	int ln_shrd_serdes_num;
 	const struct qmp_phy_init_tbl *tx;
 	int tx_num;
 	const struct qmp_phy_init_tbl *rx;
@@ -1556,6 +1787,9 @@ struct qmp_phy_cfg {
 	/* resets to be requested */
 	const char * const *reset_list;
 	int num_resets;
+	/* no CSR resets to be requested */
+	const char * const *nocsr_reset_list;
+	int num_nocsr_resets;
 	/* regulators to be requested */
 	const char * const *vreg_list;
 	int num_vregs;
@@ -1569,6 +1803,9 @@ struct qmp_phy_cfg {
 
 	bool skip_start_delay;
 
+	/* true, if PHY has lane shared serdes table */
+	bool has_ln_shrd_serdes_tbl;
+
 	/* QMP PHY pipe clock interface rate */
 	unsigned long pipe_clock_rate;
 };
@@ -1580,6 +1817,7 @@ struct qmp_pcie {
 	bool tcsr_4ln_config;
 
 	void __iomem *serdes;
+	void __iomem *ln_shrd_serdes;
 	void __iomem *pcs;
 	void __iomem *pcs_misc;
 	void __iomem *tx;
@@ -1594,6 +1832,7 @@ struct qmp_pcie {
 	int num_pipe_clks;
 
 	struct reset_control_bulk_data *resets;
+	struct reset_control_bulk_data *nocsr_resets;
 	struct regulator_bulk_data *vregs;
 
 	struct phy *phy;
@@ -1643,11 +1882,19 @@ static const char * const sdm845_pciephy_clk_l[] = {
 	"aux", "cfg_ahb", "ref", "refgen",
 };
 
+static const char * const sm8550_pciephy_clk_l[] = {
+	"aux", "aux_phy", "cfg_ahb", "ref", "rchng",
+};
+
 /* list of regulators */
 static const char * const qmp_phy_vreg_l[] = {
 	"vdda-phy", "vdda-pll",
 };
 
+static const char * const sm8550_qmp_phy_vreg_l[] = {
+	"vdda-phy", "vdda-pll", "vdda-qref",
+};
+
 /* list of resets */
 static const char * const ipq8074_pciephy_reset_l[] = {
 	"phy", "common",
@@ -1657,6 +1904,10 @@ static const char * const sdm845_pciephy_reset_l[] = {
 	"phy",
 };
 
+static const char * const sm8550_pciephy_nocsr_reset_l[] = {
+	"pcie_1_nocsr_com_phy_reset",
+};
+
 static const struct qmp_pcie_offsets qmp_pcie_offsets_v5 = {
 	.serdes		= 0,
 	.pcs		= 0x0200,
@@ -1667,6 +1918,17 @@ static const struct qmp_pcie_offsets qmp_pcie_offsets_v5 = {
 	.rx2		= 0x1800,
 };
 
+static const struct qmp_pcie_offsets qmp_pcie_offsets_v6_20 = {
+	.serdes		= 0x1000,
+	.pcs		= 0x1200,
+	.pcs_misc	= 0x1400,
+	.tx		= 0x0,
+	.rx		= 0x200,
+	.tx2		= 0x800,
+	.rx2		= 0xa00,
+	.ln_shrd	= 0xe00,
+};
+
 static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
 	.lanes			= 1,
 
@@ -2214,6 +2476,69 @@ static const struct qmp_phy_cfg sm8450_qmp_gen4x2_pciephy_cfg = {
 	.phy_status		= PHYSTATUS_4_20,
 };
 
+static const struct qmp_phy_cfg sm8550_qmp_gen3x2_pciephy_cfg = {
+	.lanes = 2,
+
+	.offsets		= &qmp_pcie_offsets_v5,
+
+	.tbls = {
+		.serdes		= sm8550_qmp_gen3x2_pcie_serdes_tbl,
+		.serdes_num	= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_serdes_tbl),
+		.tx		= sm8550_qmp_gen3x2_pcie_tx_tbl,
+		.tx_num		= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_tx_tbl),
+		.rx		= sm8550_qmp_gen3x2_pcie_rx_tbl,
+		.rx_num		= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_rx_tbl),
+		.pcs		= sm8550_qmp_gen3x2_pcie_pcs_tbl,
+		.pcs_num	= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_pcs_tbl),
+		.pcs_misc	= sm8550_qmp_gen3x2_pcie_pcs_misc_tbl,
+		.pcs_misc_num	= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_pcs_misc_tbl),
+	},
+	.clk_list		= sc8280xp_pciephy_clk_l,
+	.num_clks		= ARRAY_SIZE(sc8280xp_pciephy_clk_l),
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= pciephy_v5_regs_layout,
+
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.phy_status		= PHYSTATUS,
+};
+
+static const struct qmp_phy_cfg sm8550_qmp_gen4x2_pciephy_cfg = {
+	.lanes = 2,
+
+	.offsets		= &qmp_pcie_offsets_v6_20,
+
+	.tbls = {
+		.serdes			= sm8550_qmp_gen4x2_pcie_serdes_tbl,
+		.serdes_num		= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_serdes_tbl),
+		.ln_shrd_serdes		= sm8550_qmp_gen4x2_pcie_serdes_ln_shrd_tbl,
+		.ln_shrd_serdes_num	= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_serdes_ln_shrd_tbl),
+		.tx			= sm8550_qmp_gen4x2_pcie_tx_tbl,
+		.tx_num			= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_tx_tbl),
+		.rx			= sm8550_qmp_gen4x2_pcie_rx_tbl,
+		.rx_num			= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_rx_tbl),
+		.pcs			= sm8550_qmp_gen4x2_pcie_pcs_tbl,
+		.pcs_num		= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_tbl),
+		.pcs_misc		= sm8550_qmp_gen4x2_pcie_pcs_misc_tbl,
+		.pcs_misc_num		= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_misc_tbl),
+	},
+	.clk_list		= sm8550_pciephy_clk_l,
+	.num_clks		= ARRAY_SIZE(sm8550_pciephy_clk_l),
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.nocsr_reset_list	= sm8550_pciephy_nocsr_reset_l,
+	.num_nocsr_resets	= ARRAY_SIZE(sm8550_pciephy_nocsr_reset_l),
+	.vreg_list		= sm8550_qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(sm8550_qmp_phy_vreg_l),
+	.regs			= pciephy_v5_regs_layout,
+
+	.has_ln_shrd_serdes_tbl	= true,
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.phy_status		= PHYSTATUS_4_20,
+};
+
 static void qmp_pcie_configure_lane(void __iomem *base,
 					const struct qmp_phy_init_tbl tbl[],
 					int num,
@@ -2262,6 +2587,7 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 {
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	void __iomem *serdes = qmp->serdes;
+	void __iomem *ln_shrd_serdes = qmp->ln_shrd_serdes;
 	void __iomem *tx = qmp->tx;
 	void __iomem *rx = qmp->rx;
 	void __iomem *tx2 = qmp->tx2;
@@ -2289,6 +2615,10 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 		qmp_pcie_configure(serdes, cfg->serdes_4ln_tbl, cfg->serdes_4ln_num);
 		qmp_pcie_init_port_b(qmp, tbls);
 	}
+
+	if (cfg->has_ln_shrd_serdes_tbl)
+		qmp_pcie_configure(ln_shrd_serdes, tbls->ln_shrd_serdes,
+				       tbls->ln_shrd_serdes_num);
 }
 
 static int qmp_pcie_init(struct phy *phy)
@@ -2309,6 +2639,14 @@ static int qmp_pcie_init(struct phy *phy)
 		goto err_disable_regulators;
 	}
 
+	if (qmp->nocsr_resets) {
+		ret = reset_control_bulk_assert(cfg->num_nocsr_resets, qmp->nocsr_resets);
+		if (ret) {
+			dev_err(qmp->dev, "no-csr reset assert failed\n");
+			goto err_disable_regulators;
+		}
+	}
+
 	usleep_range(200, 300);
 
 	ret = reset_control_bulk_deassert(cfg->num_resets, qmp->resets);
@@ -2370,6 +2708,14 @@ static int qmp_pcie_power_on(struct phy *phy)
 	if (ret)
 		return ret;
 
+	if (qmp->nocsr_resets) {
+		ret = reset_control_bulk_deassert(cfg->num_nocsr_resets, qmp->nocsr_resets);
+		if (ret) {
+			dev_err(qmp->dev, "no-csr reset deassert failed\n");
+			goto err_disable_pipe_clk;
+		}
+	}
+
 	/* Pull PHY out of reset state */
 	qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
 
@@ -2503,6 +2849,21 @@ static int qmp_pcie_reset_init(struct qmp_pcie *qmp)
 	if (ret)
 		return dev_err_probe(dev, ret, "failed to get resets\n");
 
+	if (cfg->nocsr_reset_list) {
+		qmp->nocsr_resets = devm_kcalloc(dev, cfg->num_nocsr_resets,
+				   sizeof(*qmp->nocsr_resets), GFP_KERNEL);
+		if (!qmp->nocsr_resets)
+			return -ENOMEM;
+
+		for (i = 0; i < cfg->num_nocsr_resets; i++)
+			qmp->nocsr_resets[i].id = cfg->nocsr_reset_list[i];
+
+		ret = devm_reset_control_bulk_get_exclusive(dev, cfg->num_nocsr_resets,
+								qmp->nocsr_resets);
+		if (ret)
+			return dev_err_probe(dev, ret, "failed to get no CSR resets\n");
+	}
+
 	return 0;
 }
 
@@ -2713,6 +3074,8 @@ static int qmp_pcie_parse_dt(struct qmp_pcie *qmp)
 	qmp->pcs_misc = base + offs->pcs_misc;
 	qmp->tx = base + offs->tx;
 	qmp->rx = base + offs->rx;
+	if (cfg->has_ln_shrd_serdes_tbl)
+		qmp->ln_shrd_serdes = base + offs->ln_shrd;
 
 	if (cfg->lanes >= 2) {
 		qmp->tx2 = base + offs->tx2;
@@ -2865,6 +3228,12 @@ static const struct of_device_id qmp_pcie_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8450-qmp-gen4x2-pcie-phy",
 		.data = &sm8450_qmp_gen4x2_pciephy_cfg,
+	}, {
+		.compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy",
+		.data = &sm8550_qmp_gen3x2_pciephy_cfg,
+	}, {
+		.compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy",
+		.data = &sm8550_qmp_gen4x2_pciephy_cfg,
 	},
 	{ },
 };
-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Abel Vesa]

Add the SM8550 both g4 and g3 configurations. In addition, there is a
new "lane shared" table that needs to be configured for g4, along with
the No-CSR list of resets.

Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
 1 file changed, 369 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index bffb9e138715..6f82604bd430 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
 	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
 };
 
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x93),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x42),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_ADDITIONAL_MISC_3, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_4, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_PI_QEC_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x18),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_GM_CAL, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH2, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH3, 0xb7),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH4, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_LOW, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH, 0x5c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH2, 0x9c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH3, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH4, 0x89),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_LOW, 0xdc),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH, 0x94),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH2, 0x5b),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH3, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH4, 0x89),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_TX_ADAPT_POST_THRESH, 0xf0),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_FO_GAIN, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SO_GAIN, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SB2_THRESH1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_VGA_CAL_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_SIDGET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_IDAC_TSETTLE_LOW, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V6_RX_SIGDET_CAL_TRIM, 0x08),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_REFGEN_REQ_CONFIG1, 0x05),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_RX_SIGDET_LVL, 0x77),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_RATE_SLEW_CNTRL1, 0x0b),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_EQ_CONFIG2, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V6_PCS_PCS_TX_RX_CONFIG, 0x8c),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen3x2_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_OSC_DTCT_ACTIONS, 0x00),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x26),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x68),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_POST_DIV_MUX, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x46),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MISC_1, 0x88),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MODE, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_VCO_DC_LEVEL_CTRL, 0x0f),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_serdes_ln_shrd_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_Q_EN_RATES, 0xe),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3, 0x9a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5, 0xb6),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6, 0x64),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX, 0x1d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_1, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_3, 0x51),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN, 0x34),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_PI_CONTROLS, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_CAL_CTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET, 0x7c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_3, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_GM_CAL, 0x0d),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_SIGDET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_PHPRE_CTRL, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B1, 0xb3),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B2, 0x58),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B3, 0x9a),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B4, 0x26),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B5, 0xb6),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B6, 0xee),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B0, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B1, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B2, 0xa0),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B3, 0xdf),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B4, 0x78),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B5, 0x76),
+	QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B6, 0xff),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_G3S2_PRE_GAIN, 0x2e),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_COM_ELECIDLE_DLY_SEL, 0x25),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG4, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG5, 0x22),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG1, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG2, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8550_qmp_gen4x2_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE, 0xc1),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG1, 0x16),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG5, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN, 0x2e),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3, 0x28),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG, 0xc0),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5, 0xf2),
+	QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5, 0xf2),
+};
+
 struct qmp_pcie_offsets {
 	u16 serdes;
 	u16 pcs;
@@ -1514,11 +1742,14 @@ struct qmp_pcie_offsets {
 	u16 rx;
 	u16 tx2;
 	u16 rx2;
+	u16 ln_shrd;
 };
 
 struct qmp_phy_cfg_tbls {
 	const struct qmp_phy_init_tbl *serdes;
 	int serdes_num;
+	const struct qmp_phy_init_tbl *ln_shrd_serdes;
+	int ln_shrd_serdes_num;
 	const struct qmp_phy_init_tbl *tx;
 	int tx_num;
 	const struct qmp_phy_init_tbl *rx;
@@ -1556,6 +1787,9 @@ struct qmp_phy_cfg {
 	/* resets to be requested */
 	const char * const *reset_list;
 	int num_resets;
+	/* no CSR resets to be requested */
+	const char * const *nocsr_reset_list;
+	int num_nocsr_resets;
 	/* regulators to be requested */
 	const char * const *vreg_list;
 	int num_vregs;
@@ -1569,6 +1803,9 @@ struct qmp_phy_cfg {
 
 	bool skip_start_delay;
 
+	/* true, if PHY has lane shared serdes table */
+	bool has_ln_shrd_serdes_tbl;
+
 	/* QMP PHY pipe clock interface rate */
 	unsigned long pipe_clock_rate;
 };
@@ -1580,6 +1817,7 @@ struct qmp_pcie {
 	bool tcsr_4ln_config;
 
 	void __iomem *serdes;
+	void __iomem *ln_shrd_serdes;
 	void __iomem *pcs;
 	void __iomem *pcs_misc;
 	void __iomem *tx;
@@ -1594,6 +1832,7 @@ struct qmp_pcie {
 	int num_pipe_clks;
 
 	struct reset_control_bulk_data *resets;
+	struct reset_control_bulk_data *nocsr_resets;
 	struct regulator_bulk_data *vregs;
 
 	struct phy *phy;
@@ -1643,11 +1882,19 @@ static const char * const sdm845_pciephy_clk_l[] = {
 	"aux", "cfg_ahb", "ref", "refgen",
 };
 
+static const char * const sm8550_pciephy_clk_l[] = {
+	"aux", "aux_phy", "cfg_ahb", "ref", "rchng",
+};
+
 /* list of regulators */
 static const char * const qmp_phy_vreg_l[] = {
 	"vdda-phy", "vdda-pll",
 };
 
+static const char * const sm8550_qmp_phy_vreg_l[] = {
+	"vdda-phy", "vdda-pll", "vdda-qref",
+};
+
 /* list of resets */
 static const char * const ipq8074_pciephy_reset_l[] = {
 	"phy", "common",
@@ -1657,6 +1904,10 @@ static const char * const sdm845_pciephy_reset_l[] = {
 	"phy",
 };
 
+static const char * const sm8550_pciephy_nocsr_reset_l[] = {
+	"pcie_1_nocsr_com_phy_reset",
+};
+
 static const struct qmp_pcie_offsets qmp_pcie_offsets_v5 = {
 	.serdes		= 0,
 	.pcs		= 0x0200,
@@ -1667,6 +1918,17 @@ static const struct qmp_pcie_offsets qmp_pcie_offsets_v5 = {
 	.rx2		= 0x1800,
 };
 
+static const struct qmp_pcie_offsets qmp_pcie_offsets_v6_20 = {
+	.serdes		= 0x1000,
+	.pcs		= 0x1200,
+	.pcs_misc	= 0x1400,
+	.tx		= 0x0,
+	.rx		= 0x200,
+	.tx2		= 0x800,
+	.rx2		= 0xa00,
+	.ln_shrd	= 0xe00,
+};
+
 static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
 	.lanes			= 1,
 
@@ -2214,6 +2476,69 @@ static const struct qmp_phy_cfg sm8450_qmp_gen4x2_pciephy_cfg = {
 	.phy_status		= PHYSTATUS_4_20,
 };
 
+static const struct qmp_phy_cfg sm8550_qmp_gen3x2_pciephy_cfg = {
+	.lanes = 2,
+
+	.offsets		= &qmp_pcie_offsets_v5,
+
+	.tbls = {
+		.serdes		= sm8550_qmp_gen3x2_pcie_serdes_tbl,
+		.serdes_num	= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_serdes_tbl),
+		.tx		= sm8550_qmp_gen3x2_pcie_tx_tbl,
+		.tx_num		= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_tx_tbl),
+		.rx		= sm8550_qmp_gen3x2_pcie_rx_tbl,
+		.rx_num		= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_rx_tbl),
+		.pcs		= sm8550_qmp_gen3x2_pcie_pcs_tbl,
+		.pcs_num	= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_pcs_tbl),
+		.pcs_misc	= sm8550_qmp_gen3x2_pcie_pcs_misc_tbl,
+		.pcs_misc_num	= ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_pcs_misc_tbl),
+	},
+	.clk_list		= sc8280xp_pciephy_clk_l,
+	.num_clks		= ARRAY_SIZE(sc8280xp_pciephy_clk_l),
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= pciephy_v5_regs_layout,
+
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.phy_status		= PHYSTATUS,
+};
+
+static const struct qmp_phy_cfg sm8550_qmp_gen4x2_pciephy_cfg = {
+	.lanes = 2,
+
+	.offsets		= &qmp_pcie_offsets_v6_20,
+
+	.tbls = {
+		.serdes			= sm8550_qmp_gen4x2_pcie_serdes_tbl,
+		.serdes_num		= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_serdes_tbl),
+		.ln_shrd_serdes		= sm8550_qmp_gen4x2_pcie_serdes_ln_shrd_tbl,
+		.ln_shrd_serdes_num	= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_serdes_ln_shrd_tbl),
+		.tx			= sm8550_qmp_gen4x2_pcie_tx_tbl,
+		.tx_num			= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_tx_tbl),
+		.rx			= sm8550_qmp_gen4x2_pcie_rx_tbl,
+		.rx_num			= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_rx_tbl),
+		.pcs			= sm8550_qmp_gen4x2_pcie_pcs_tbl,
+		.pcs_num		= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_tbl),
+		.pcs_misc		= sm8550_qmp_gen4x2_pcie_pcs_misc_tbl,
+		.pcs_misc_num		= ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_misc_tbl),
+	},
+	.clk_list		= sm8550_pciephy_clk_l,
+	.num_clks		= ARRAY_SIZE(sm8550_pciephy_clk_l),
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.nocsr_reset_list	= sm8550_pciephy_nocsr_reset_l,
+	.num_nocsr_resets	= ARRAY_SIZE(sm8550_pciephy_nocsr_reset_l),
+	.vreg_list		= sm8550_qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(sm8550_qmp_phy_vreg_l),
+	.regs			= pciephy_v5_regs_layout,
+
+	.has_ln_shrd_serdes_tbl	= true,
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.phy_status		= PHYSTATUS_4_20,
+};
+
 static void qmp_pcie_configure_lane(void __iomem *base,
 					const struct qmp_phy_init_tbl tbl[],
 					int num,
@@ -2262,6 +2587,7 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 {
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	void __iomem *serdes = qmp->serdes;
+	void __iomem *ln_shrd_serdes = qmp->ln_shrd_serdes;
 	void __iomem *tx = qmp->tx;
 	void __iomem *rx = qmp->rx;
 	void __iomem *tx2 = qmp->tx2;
@@ -2289,6 +2615,10 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
 		qmp_pcie_configure(serdes, cfg->serdes_4ln_tbl, cfg->serdes_4ln_num);
 		qmp_pcie_init_port_b(qmp, tbls);
 	}
+
+	if (cfg->has_ln_shrd_serdes_tbl)
+		qmp_pcie_configure(ln_shrd_serdes, tbls->ln_shrd_serdes,
+				       tbls->ln_shrd_serdes_num);
 }
 
 static int qmp_pcie_init(struct phy *phy)
@@ -2309,6 +2639,14 @@ static int qmp_pcie_init(struct phy *phy)
 		goto err_disable_regulators;
 	}
 
+	if (qmp->nocsr_resets) {
+		ret = reset_control_bulk_assert(cfg->num_nocsr_resets, qmp->nocsr_resets);
+		if (ret) {
+			dev_err(qmp->dev, "no-csr reset assert failed\n");
+			goto err_disable_regulators;
+		}
+	}
+
 	usleep_range(200, 300);
 
 	ret = reset_control_bulk_deassert(cfg->num_resets, qmp->resets);
@@ -2370,6 +2708,14 @@ static int qmp_pcie_power_on(struct phy *phy)
 	if (ret)
 		return ret;
 
+	if (qmp->nocsr_resets) {
+		ret = reset_control_bulk_deassert(cfg->num_nocsr_resets, qmp->nocsr_resets);
+		if (ret) {
+			dev_err(qmp->dev, "no-csr reset deassert failed\n");
+			goto err_disable_pipe_clk;
+		}
+	}
+
 	/* Pull PHY out of reset state */
 	qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
 
@@ -2503,6 +2849,21 @@ static int qmp_pcie_reset_init(struct qmp_pcie *qmp)
 	if (ret)
 		return dev_err_probe(dev, ret, "failed to get resets\n");
 
+	if (cfg->nocsr_reset_list) {
+		qmp->nocsr_resets = devm_kcalloc(dev, cfg->num_nocsr_resets,
+				   sizeof(*qmp->nocsr_resets), GFP_KERNEL);
+		if (!qmp->nocsr_resets)
+			return -ENOMEM;
+
+		for (i = 0; i < cfg->num_nocsr_resets; i++)
+			qmp->nocsr_resets[i].id = cfg->nocsr_reset_list[i];
+
+		ret = devm_reset_control_bulk_get_exclusive(dev, cfg->num_nocsr_resets,
+								qmp->nocsr_resets);
+		if (ret)
+			return dev_err_probe(dev, ret, "failed to get no CSR resets\n");
+	}
+
 	return 0;
 }
 
@@ -2713,6 +3074,8 @@ static int qmp_pcie_parse_dt(struct qmp_pcie *qmp)
 	qmp->pcs_misc = base + offs->pcs_misc;
 	qmp->tx = base + offs->tx;
 	qmp->rx = base + offs->rx;
+	if (cfg->has_ln_shrd_serdes_tbl)
+		qmp->ln_shrd_serdes = base + offs->ln_shrd;
 
 	if (cfg->lanes >= 2) {
 		qmp->tx2 = base + offs->tx2;
@@ -2865,6 +3228,12 @@ static const struct of_device_id qmp_pcie_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8450-qmp-gen4x2-pcie-phy",
 		.data = &sm8450_qmp_gen4x2_pciephy_cfg,
+	}, {
+		.compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy",
+		.data = &sm8550_qmp_gen3x2_pciephy_cfg,
+	}, {
+		.compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy",
+		.data = &sm8550_qmp_gen4x2_pciephy_cfg,
 	},
 	{ },
 };
-- 
2.34.1

Re: [PATCH v3 2/8] phy: qcom-qmp: pcs: Add v6 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
> UFS and PCIE g3x2. Add the new PCS offsets in a dedicated header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h | 16 ++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h        |  2 ++
>   2 files changed, 18 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

Re: [PATCH v3 2/8] phy: qcom-qmp: pcs: Add v6 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
> UFS and PCIE g3x2. Add the new PCS offsets in a dedicated header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h | 16 ++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h        |  2 ++
>   2 files changed, 18 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 4/8] phy: qcom-qmp: pcs-pcie: Add v6 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
> UFS and PCIE g3x2. Add the new PCS PCIE specific offsets in a dedicated
> header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c        |  1 +
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h | 15 +++++++++++++++
>   2 files changed, 16 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

Re: [PATCH v3 4/8] phy: qcom-qmp: pcs-pcie: Add v6 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
> UFS and PCIE g3x2. Add the new PCS PCIE specific offsets in a dedicated
> header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c        |  1 +
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h | 15 +++++++++++++++
>   2 files changed, 16 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 3/8] phy: qcom-qmp: pcs: Add v6.20 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
> PCIE g4x2. Add the new PCS offsets in a dedicated header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h | 18 ++++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h           |  2 ++
>   2 files changed, 20 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h

I can not verify register offsets, but generally looks good. Thus:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

Re: [PATCH v3 3/8] phy: qcom-qmp: pcs: Add v6.20 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
> PCIE g4x2. Add the new PCS offsets in a dedicated header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h | 18 ++++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h           |  2 ++
>   2 files changed, 20 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h

I can not verify register offsets, but generally looks good. Thus:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 5/8] phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
> PCIE g4x2. Add the new PCS PCIE specific offsets in a dedicated
> header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      |  1 +
>   .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h    | 23 +++++++++++++++++++
>   2 files changed, 24 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

Re: [PATCH v3 5/8] phy: qcom-qmp: pcs-pcie: Add v6.20 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
> PCIE g4x2. Add the new PCS PCIE specific offsets in a dedicated
> header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      |  1 +
>   .../qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h    | 23 +++++++++++++++++++
>   2 files changed, 24 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 6/8] phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
> PCIE g4x2. Add the new qserdes TX RX PCIE specific offsets in a
> dedicated header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   .../phy-qcom-qmp-qserdes-txrx-v6_20.h         | 45 +++++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h           |  1 +
>   2 files changed, 46 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

Re: [PATCH v3 6/8] phy: qcom-qmp: qserdes-txrx: Add v6.20 register offsets

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
> PCIE g4x2. Add the new qserdes TX RX PCIE specific offsets in a
> dedicated header file.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   .../phy-qcom-qmp-qserdes-txrx-v6_20.h         | 45 +++++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h           |  1 +
>   2 files changed, 46 insertions(+)
>   create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> Add the SM8550 both g4 and g3 configurations. In addition, there is a
> new "lane shared" table that needs to be configured for g4, along with
> the No-CSR list of resets.
> 
> Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
>   1 file changed, 369 insertions(+)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> index bffb9e138715..6f82604bd430 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> @@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
>   	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
>   };

I see that the last two patches still use 'shrd' a lot. Does this 
correspond to hw register names or is it just a vendor kernel code 
convention?

-- 
With best wishes
Dmitry

Re: [PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Dmitry Baryshkov]

On 18/01/2023 02:53, Abel Vesa wrote:
> Add the SM8550 both g4 and g3 configurations. In addition, there is a
> new "lane shared" table that needs to be configured for g4, along with
> the No-CSR list of resets.
> 
> Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
>   1 file changed, 369 insertions(+)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> index bffb9e138715..6f82604bd430 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> @@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
>   	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
>   };

I see that the last two patches still use 'shrd' a lot. Does this 
correspond to hw register names or is it just a vendor kernel code 
convention?

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Rob Herring]

On Wed, 18 Jan 2023 02:53:21 +0200, Abel Vesa wrote:
> Document the QMP PCIe PHY compatible for SM8550.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Rob Herring]

On Wed, 18 Jan 2023 02:53:21 +0200, Abel Vesa wrote:
> Document the QMP PCIe PHY compatible for SM8550.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Johan Hovold]

On Wed, Jan 18, 2023 at 02:53:21AM +0200, Abel Vesa wrote:
> Document the QMP PCIe PHY compatible for SM8550.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> index 8a85318d9c92..65f26cfff3fb 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> @@ -20,6 +20,8 @@ properties:
>        - qcom,sc8280xp-qmp-gen3x2-pcie-phy
>        - qcom,sc8280xp-qmp-gen3x4-pcie-phy
>        - qcom,sm8350-qmp-gen3x1-pcie-phy
> +      - qcom,sm8550-qmp-gen3x2-pcie-phy
> +      - qcom,sm8550-qmp-gen4x2-pcie-phy
>  
>    reg:
>      minItems: 1

I don't think I'll have time to look at this week, but I did notice that
you fail do describe the clocks, regulators, and resets (as you also
did for the UFS PHY binding) which are currently different from
sc8280xp.

Please be more careful when adding compatible strings so we get this
right. You should also double check that the differences are really
warranted and not just due the vendor using different names for the same
resource.

At least the reset must be renamed ("pcie_1_nocsr_com_phy_reset", e.g.
drop 'pcie' and 'reset', maybe more).

Johan

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Johan Hovold]

On Wed, Jan 18, 2023 at 02:53:21AM +0200, Abel Vesa wrote:
> Document the QMP PCIe PHY compatible for SM8550.
> 
> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> ---
>  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> index 8a85318d9c92..65f26cfff3fb 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> @@ -20,6 +20,8 @@ properties:
>        - qcom,sc8280xp-qmp-gen3x2-pcie-phy
>        - qcom,sc8280xp-qmp-gen3x4-pcie-phy
>        - qcom,sm8350-qmp-gen3x1-pcie-phy
> +      - qcom,sm8550-qmp-gen3x2-pcie-phy
> +      - qcom,sm8550-qmp-gen4x2-pcie-phy
>  
>    reg:
>      minItems: 1

I don't think I'll have time to look at this week, but I did notice that
you fail do describe the clocks, regulators, and resets (as you also
did for the UFS PHY binding) which are currently different from
sc8280xp.

Please be more careful when adding compatible strings so we get this
right. You should also double check that the differences are really
warranted and not just due the vendor using different names for the same
resource.

At least the reset must be renamed ("pcie_1_nocsr_com_phy_reset", e.g.
drop 'pcie' and 'reset', maybe more).

Johan

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Abel Vesa]

On 23-01-18 17:45:16, Johan Hovold wrote:
> On Wed, Jan 18, 2023 at 02:53:21AM +0200, Abel Vesa wrote:
> > Document the QMP PCIe PHY compatible for SM8550.
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
> >  1 file changed, 2 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > index 8a85318d9c92..65f26cfff3fb 100644
> > --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > @@ -20,6 +20,8 @@ properties:
> >        - qcom,sc8280xp-qmp-gen3x2-pcie-phy
> >        - qcom,sc8280xp-qmp-gen3x4-pcie-phy
> >        - qcom,sm8350-qmp-gen3x1-pcie-phy
> > +      - qcom,sm8550-qmp-gen3x2-pcie-phy
> > +      - qcom,sm8550-qmp-gen4x2-pcie-phy
> >  
> >    reg:
> >      minItems: 1
> 
> I don't think I'll have time to look at this week, but I did notice that
> you fail do describe the clocks, regulators, and resets (as you also
> did for the UFS PHY binding) which are currently different from
> sc8280xp.

Hmm, sorry about that. I will double check against the pcie phy nodes I
have for sm8550.

As for the UFS, if your are referring to the following patchset [1], the phy
node looks exactly the same as on sc8280xp, therefore no other binding
update, other than compatible, was needed.

[1] https://lore.kernel.org/all/20230117224148.1914627-2-abel.vesa@linaro.org/

> 
> Please be more careful when adding compatible strings so we get this
> right. You should also double check that the differences are really
> warranted and not just due the vendor using different names for the same
> resource.
> 
> At least the reset must be renamed ("pcie_1_nocsr_com_phy_reset", e.g.
> drop 'pcie' and 'reset', maybe more).
> 
> Johan

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Abel Vesa]

On 23-01-18 17:45:16, Johan Hovold wrote:
> On Wed, Jan 18, 2023 at 02:53:21AM +0200, Abel Vesa wrote:
> > Document the QMP PCIe PHY compatible for SM8550.
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
> >  1 file changed, 2 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > index 8a85318d9c92..65f26cfff3fb 100644
> > --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > @@ -20,6 +20,8 @@ properties:
> >        - qcom,sc8280xp-qmp-gen3x2-pcie-phy
> >        - qcom,sc8280xp-qmp-gen3x4-pcie-phy
> >        - qcom,sm8350-qmp-gen3x1-pcie-phy
> > +      - qcom,sm8550-qmp-gen3x2-pcie-phy
> > +      - qcom,sm8550-qmp-gen4x2-pcie-phy
> >  
> >    reg:
> >      minItems: 1
> 
> I don't think I'll have time to look at this week, but I did notice that
> you fail do describe the clocks, regulators, and resets (as you also
> did for the UFS PHY binding) which are currently different from
> sc8280xp.

Hmm, sorry about that. I will double check against the pcie phy nodes I
have for sm8550.

As for the UFS, if your are referring to the following patchset [1], the phy
node looks exactly the same as on sc8280xp, therefore no other binding
update, other than compatible, was needed.

[1] https://lore.kernel.org/all/20230117224148.1914627-2-abel.vesa@linaro.org/

> 
> Please be more careful when adding compatible strings so we get this
> right. You should also double check that the differences are really
> warranted and not just due the vendor using different names for the same
> resource.
> 
> At least the reset must be renamed ("pcie_1_nocsr_com_phy_reset", e.g.
> drop 'pcie' and 'reset', maybe more).
> 
> Johan

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Abel Vesa]

On 23-01-18 06:34:41, Dmitry Baryshkov wrote:
> On 18/01/2023 02:53, Abel Vesa wrote:
> > Add the SM8550 both g4 and g3 configurations. In addition, there is a
> > new "lane shared" table that needs to be configured for g4, along with
> > the No-CSR list of resets.
> > 
> > Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
> > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
> >   1 file changed, 369 insertions(+)
> > 
> > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > index bffb9e138715..6f82604bd430 100644
> > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > @@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
> >   	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
> >   };
> 
> I see that the last two patches still use 'shrd' a lot. Does this correspond
> to hw register names or is it just a vendor kernel code convention?

It corresponds to the hw register names..

> 
> -- 
> With best wishes
> Dmitry
> 

Re: [PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Abel Vesa]

On 23-01-18 06:34:41, Dmitry Baryshkov wrote:
> On 18/01/2023 02:53, Abel Vesa wrote:
> > Add the SM8550 both g4 and g3 configurations. In addition, there is a
> > new "lane shared" table that needs to be configured for g4, along with
> > the No-CSR list of resets.
> > 
> > Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
> > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> >   drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
> >   1 file changed, 369 insertions(+)
> > 
> > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > index bffb9e138715..6f82604bd430 100644
> > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
> > @@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
> >   	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
> >   };
> 
> I see that the last two patches still use 'shrd' a lot. Does this correspond
> to hw register names or is it just a vendor kernel code convention?

It corresponds to the hw register names..

> 
> -- 
> With best wishes
> Dmitry
> 

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Johan Hovold]

On Wed, Jan 18, 2023 at 11:25:31PM +0200, Abel Vesa wrote:
> On 23-01-18 17:45:16, Johan Hovold wrote:
> > On Wed, Jan 18, 2023 at 02:53:21AM +0200, Abel Vesa wrote:
> > > Document the QMP PCIe PHY compatible for SM8550.
> > > 
> > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > > ---
> > >  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
> > >  1 file changed, 2 insertions(+)
> > > 
> > > diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > > index 8a85318d9c92..65f26cfff3fb 100644
> > > --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > > +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > > @@ -20,6 +20,8 @@ properties:
> > >        - qcom,sc8280xp-qmp-gen3x2-pcie-phy
> > >        - qcom,sc8280xp-qmp-gen3x4-pcie-phy
> > >        - qcom,sm8350-qmp-gen3x1-pcie-phy
> > > +      - qcom,sm8550-qmp-gen3x2-pcie-phy
> > > +      - qcom,sm8550-qmp-gen4x2-pcie-phy
> > >  
> > >    reg:
> > >      minItems: 1
> > 
> > I don't think I'll have time to look at this week, but I did notice that
> > you fail do describe the clocks, regulators, and resets (as you also
> > did for the UFS PHY binding) which are currently different from
> > sc8280xp.
> 
> Hmm, sorry about that. I will double check against the pcie phy nodes I
> have for sm8550.
> 
> As for the UFS, if your are referring to the following patchset [1], the phy
> node looks exactly the same as on sc8280xp, therefore no other binding
> update, other than compatible, was needed.
> 
> [1] https://lore.kernel.org/all/20230117224148.1914627-2-abel.vesa@linaro.org/

Yes, but I was referring to your original submission which added
different names for the clocks without updating the binding. In that
case, those clocks were really the same ones as the ones on sc8280xp so
it was only the driver and dts changes that were wrong:

	https://lore.kernel.org/all/Y8And9VVvpnSInlj@hovoldconsulting.com/

> > Please be more careful when adding compatible strings so we get this
> > right. You should also double check that the differences are really
> > warranted and not just due the vendor using different names for the same
> > resource.

Johan

Re: [PATCH v3 1/8] dt-bindings: phy: Add QMP PCIe PHY comptible for SM8550

[Johan Hovold]

On Wed, Jan 18, 2023 at 11:25:31PM +0200, Abel Vesa wrote:
> On 23-01-18 17:45:16, Johan Hovold wrote:
> > On Wed, Jan 18, 2023 at 02:53:21AM +0200, Abel Vesa wrote:
> > > Document the QMP PCIe PHY compatible for SM8550.
> > > 
> > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > > ---
> > >  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml     | 2 ++
> > >  1 file changed, 2 insertions(+)
> > > 
> > > diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > > index 8a85318d9c92..65f26cfff3fb 100644
> > > --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > > +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml
> > > @@ -20,6 +20,8 @@ properties:
> > >        - qcom,sc8280xp-qmp-gen3x2-pcie-phy
> > >        - qcom,sc8280xp-qmp-gen3x4-pcie-phy
> > >        - qcom,sm8350-qmp-gen3x1-pcie-phy
> > > +      - qcom,sm8550-qmp-gen3x2-pcie-phy
> > > +      - qcom,sm8550-qmp-gen4x2-pcie-phy
> > >  
> > >    reg:
> > >      minItems: 1
> > 
> > I don't think I'll have time to look at this week, but I did notice that
> > you fail do describe the clocks, regulators, and resets (as you also
> > did for the UFS PHY binding) which are currently different from
> > sc8280xp.
> 
> Hmm, sorry about that. I will double check against the pcie phy nodes I
> have for sm8550.
> 
> As for the UFS, if your are referring to the following patchset [1], the phy
> node looks exactly the same as on sc8280xp, therefore no other binding
> update, other than compatible, was needed.
> 
> [1] https://lore.kernel.org/all/20230117224148.1914627-2-abel.vesa@linaro.org/

Yes, but I was referring to your original submission which added
different names for the clocks without updating the binding. In that
case, those clocks were really the same ones as the ones on sc8280xp so
it was only the driver and dts changes that were wrong:

	https://lore.kernel.org/all/Y8And9VVvpnSInlj@hovoldconsulting.com/

> > Please be more careful when adding compatible strings so we get this
> > right. You should also double check that the differences are really
> > warranted and not just due the vendor using different names for the same
> > resource.

Johan

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Dmitry Baryshkov]

On 19/01/2023 01:34, Abel Vesa wrote:
> On 23-01-18 06:34:41, Dmitry Baryshkov wrote:
>> On 18/01/2023 02:53, Abel Vesa wrote:
>>> Add the SM8550 both g4 and g3 configurations. In addition, there is a
>>> new "lane shared" table that needs to be configured for g4, along with
>>> the No-CSR list of resets.
>>>
>>> Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
>>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>>> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
>>> ---
>>>    drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
>>>    1 file changed, 369 insertions(+)
>>>
>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>>> index bffb9e138715..6f82604bd430 100644
>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>>> @@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
>>>    	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
>>>    };
>>
>> I see that the last two patches still use 'shrd' a lot. Does this correspond
>> to hw register names or is it just a vendor kernel code convention?
> 
> It corresponds to the hw register names..

Ack, then:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

> 
>>
>> -- 
>> With best wishes
>> Dmitry
>>

-- 
With best wishes
Dmitry

Re: [PATCH v3 8/8] phy: qcom-qmp-pcie: Add support for SM8550 g3x2 and g4x2 PCIEs

[Dmitry Baryshkov]

On 19/01/2023 01:34, Abel Vesa wrote:
> On 23-01-18 06:34:41, Dmitry Baryshkov wrote:
>> On 18/01/2023 02:53, Abel Vesa wrote:
>>> Add the SM8550 both g4 and g3 configurations. In addition, there is a
>>> new "lane shared" table that needs to be configured for g4, along with
>>> the No-CSR list of resets.
>>>
>>> Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
>>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>>> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
>>> ---
>>>    drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 369 +++++++++++++++++++++++
>>>    1 file changed, 369 insertions(+)
>>>
>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>>> index bffb9e138715..6f82604bd430 100644
>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
>>> @@ -1506,6 +1506,234 @@ static const struct qmp_phy_init_tbl sm8450_qmp_gen4x2_pcie_ep_pcs_misc_tbl[] =
>>>    	QMP_PHY_INIT_CFG(QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5, 0x08),
>>>    };
>>
>> I see that the last two patches still use 'shrd' a lot. Does this correspond
>> to hw register names or is it just a vendor kernel code convention?
> 
> It corresponds to the hw register names..

Ack, then:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

> 
>>
>> -- 
>> With best wishes
>> Dmitry
>>

-- 
With best wishes
Dmitry


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy