[PATCH v3 0/7] drm: rcar-du: Misc patches

[PATCH v3 0/7] drm: rcar-du: Misc patches

[Tomi Valkeinen]

From: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>

Hi,

Diff to v2:
- Depend on PM in Kconfig to ensure runtime PM works
- Fix access to DEFR7 in "drm: rcar-du: Stop accessing non-existant
  registers on gen4"
- Use pm_runtime_put_sync() instead of pm_runtime_put()
- Add missing line feed
- Fix lvsd typo in commit message

 Tomi

Koji Matsuoka (1):
  drm: rcar-du: lvds: Fix stop sequence

Tomi Valkeinen (6):
  drm: rcar-du: dsi: add 'select RESET_CONTROLLER'
  drm: rcar-du: lvds: Add runtime PM
  drm: rcar-du: lvds: Add reset control
  drm: rcar-du: Add quirk for H3 ES1.x pclk workaround
  drm: rcar-du: Fix setting a reserved bit in DPLLCR
  drm: rcar-du: Stop accessing non-existant registers on gen4

 drivers/gpu/drm/rcar-du/Kconfig         |  3 +
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c  | 39 +++++++----
 drivers/gpu/drm/rcar-du/rcar_du_drv.c   | 49 ++++++++++++++
 drivers/gpu/drm/rcar-du/rcar_du_drv.h   |  2 +
 drivers/gpu/drm/rcar-du/rcar_du_group.c | 24 ++++---
 drivers/gpu/drm/rcar-du/rcar_du_regs.h  |  8 +--
 drivers/gpu/drm/rcar-du/rcar_lvds.c     | 87 +++++++++++++++++++++++--
 7 files changed, 177 insertions(+), 35 deletions(-)

Interdiff against v2:
diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index 151e400b996d..742f6f2c8de8 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -39,6 +39,7 @@ config DRM_RCAR_USE_LVDS
 config DRM_RCAR_LVDS
 	def_tristate DRM_RCAR_DU
 	depends on DRM_RCAR_USE_LVDS
+	depends on PM
 	select DRM_KMS_HELPER
 	select DRM_PANEL
 	select OF_FLATTREE
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_group.c b/drivers/gpu/drm/rcar-du/rcar_du_group.c
index c2209d427bb7..152602236377 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_group.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_group.c
@@ -151,14 +151,16 @@ static void rcar_du_group_setup(struct rcar_du_group *rgrp)
 	if (rcdu->info->gen < 4)
 		rcar_du_group_setup_pins(rgrp);
 
-	/*
-	 * TODO: Handle routing of the DU output to CMM dynamically, as we
-	 * should bypass CMM completely when no color management feature is
-	 * used.
-	 */
-	defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
-		 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
-	rcar_du_group_write(rgrp, DEFR7, defr7);
+	if (rcdu->info->gen < 4) {
+		/*
+		 * TODO: Handle routing of the DU output to CMM dynamically, as
+		 * we should bypass CMM completely when no color management
+		 * feature is used.
+		 */
+		defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
+			 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
+		rcar_du_group_write(rgrp, DEFR7, defr7);
+	}
 
 	if (rcdu->info->gen >= 2) {
 		if (rcdu->info->gen < 4)
@@ -194,13 +196,10 @@ static void rcar_du_group_setup(struct rcar_du_group *rgrp)
  */
 int rcar_du_group_get(struct rcar_du_group *rgrp)
 {
-	struct rcar_du_device *rcdu = rgrp->dev;
-
 	if (rgrp->use_count)
 		goto done;
 
-	if (rcdu->info->gen < 4)
-		rcar_du_group_setup(rgrp);
+	rcar_du_group_setup(rgrp);
 
 done:
 	rgrp->use_count++;
diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index 8fa5f7400179..8cd86a3d65a5 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -345,7 +345,7 @@ void rcar_lvds_pclk_disable(struct drm_bridge *bridge)
 
 	rcar_lvds_write(lvds, LVDPLLCR, 0);
 
-	pm_runtime_put(lvds->dev);
+	pm_runtime_put_sync(lvds->dev);
 }
 EXPORT_SYMBOL_GPL(rcar_lvds_pclk_disable);
 
@@ -580,7 +580,7 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 		lvds->companion->funcs->atomic_disable(lvds->companion,
 						       old_bridge_state);
 
-	pm_runtime_put(lvds->dev);
+	pm_runtime_put_sync(lvds->dev);
 }
 
 static bool rcar_lvds_mode_fixup(struct drm_bridge *bridge,
@@ -877,6 +877,7 @@ static int rcar_lvds_probe(struct platform_device *pdev)
 	if (IS_ERR(lvds->rstc))
 		return dev_err_probe(&pdev->dev, PTR_ERR(lvds->rstc),
 				     "failed to get cpg reset\n");
+
 	pm_runtime_enable(&pdev->dev);
 
 	drm_bridge_add(&lvds->bridge);
-- 
2.34.1

[PATCH v3 0/7] drm: rcar-du: Misc patches

[Tomi Valkeinen]

From: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>

Hi,

Diff to v2:
- Depend on PM in Kconfig to ensure runtime PM works
- Fix access to DEFR7 in "drm: rcar-du: Stop accessing non-existant
  registers on gen4"
- Use pm_runtime_put_sync() instead of pm_runtime_put()
- Add missing line feed
- Fix lvsd typo in commit message

 Tomi

Koji Matsuoka (1):
  drm: rcar-du: lvds: Fix stop sequence

Tomi Valkeinen (6):
  drm: rcar-du: dsi: add 'select RESET_CONTROLLER'
  drm: rcar-du: lvds: Add runtime PM
  drm: rcar-du: lvds: Add reset control
  drm: rcar-du: Add quirk for H3 ES1.x pclk workaround
  drm: rcar-du: Fix setting a reserved bit in DPLLCR
  drm: rcar-du: Stop accessing non-existant registers on gen4

 drivers/gpu/drm/rcar-du/Kconfig         |  3 +
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c  | 39 +++++++----
 drivers/gpu/drm/rcar-du/rcar_du_drv.c   | 49 ++++++++++++++
 drivers/gpu/drm/rcar-du/rcar_du_drv.h   |  2 +
 drivers/gpu/drm/rcar-du/rcar_du_group.c | 24 ++++---
 drivers/gpu/drm/rcar-du/rcar_du_regs.h  |  8 +--
 drivers/gpu/drm/rcar-du/rcar_lvds.c     | 87 +++++++++++++++++++++++--
 7 files changed, 177 insertions(+), 35 deletions(-)

Interdiff against v2:
diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index 151e400b996d..742f6f2c8de8 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -39,6 +39,7 @@ config DRM_RCAR_USE_LVDS
 config DRM_RCAR_LVDS
 	def_tristate DRM_RCAR_DU
 	depends on DRM_RCAR_USE_LVDS
+	depends on PM
 	select DRM_KMS_HELPER
 	select DRM_PANEL
 	select OF_FLATTREE
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_group.c b/drivers/gpu/drm/rcar-du/rcar_du_group.c
index c2209d427bb7..152602236377 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_group.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_group.c
@@ -151,14 +151,16 @@ static void rcar_du_group_setup(struct rcar_du_group *rgrp)
 	if (rcdu->info->gen < 4)
 		rcar_du_group_setup_pins(rgrp);
 
-	/*
-	 * TODO: Handle routing of the DU output to CMM dynamically, as we
-	 * should bypass CMM completely when no color management feature is
-	 * used.
-	 */
-	defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
-		 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
-	rcar_du_group_write(rgrp, DEFR7, defr7);
+	if (rcdu->info->gen < 4) {
+		/*
+		 * TODO: Handle routing of the DU output to CMM dynamically, as
+		 * we should bypass CMM completely when no color management
+		 * feature is used.
+		 */
+		defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
+			 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
+		rcar_du_group_write(rgrp, DEFR7, defr7);
+	}
 
 	if (rcdu->info->gen >= 2) {
 		if (rcdu->info->gen < 4)
@@ -194,13 +196,10 @@ static void rcar_du_group_setup(struct rcar_du_group *rgrp)
  */
 int rcar_du_group_get(struct rcar_du_group *rgrp)
 {
-	struct rcar_du_device *rcdu = rgrp->dev;
-
 	if (rgrp->use_count)
 		goto done;
 
-	if (rcdu->info->gen < 4)
-		rcar_du_group_setup(rgrp);
+	rcar_du_group_setup(rgrp);
 
 done:
 	rgrp->use_count++;
diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index 8fa5f7400179..8cd86a3d65a5 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -345,7 +345,7 @@ void rcar_lvds_pclk_disable(struct drm_bridge *bridge)
 
 	rcar_lvds_write(lvds, LVDPLLCR, 0);
 
-	pm_runtime_put(lvds->dev);
+	pm_runtime_put_sync(lvds->dev);
 }
 EXPORT_SYMBOL_GPL(rcar_lvds_pclk_disable);
 
@@ -580,7 +580,7 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 		lvds->companion->funcs->atomic_disable(lvds->companion,
 						       old_bridge_state);
 
-	pm_runtime_put(lvds->dev);
+	pm_runtime_put_sync(lvds->dev);
 }
 
 static bool rcar_lvds_mode_fixup(struct drm_bridge *bridge,
@@ -877,6 +877,7 @@ static int rcar_lvds_probe(struct platform_device *pdev)
 	if (IS_ERR(lvds->rstc))
 		return dev_err_probe(&pdev->dev, PTR_ERR(lvds->rstc),
 				     "failed to get cpg reset\n");
+
 	pm_runtime_enable(&pdev->dev);
 
 	drm_bridge_add(&lvds->bridge);
-- 
2.34.1

[PATCH v3 1/7] drm: rcar-du: dsi: add 'select RESET_CONTROLLER'

[Tomi Valkeinen]

The RCAR DSI driver uses reset controller, so we should select it in the
Kconfig.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index fd2c2eaee26b..a8f862c68b4f 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -55,6 +55,7 @@ config DRM_RCAR_MIPI_DSI
 	def_tristate DRM_RCAR_DU
 	depends on DRM_RCAR_USE_MIPI_DSI
 	select DRM_MIPI_DSI
+	select RESET_CONTROLLER
 
 config DRM_RCAR_VSP
 	bool "R-Car DU VSP Compositor Support" if ARM
-- 
2.34.1

[PATCH v3 1/7] drm: rcar-du: dsi: add 'select RESET_CONTROLLER'

[Tomi Valkeinen]

The RCAR DSI driver uses reset controller, so we should select it in the
Kconfig.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index fd2c2eaee26b..a8f862c68b4f 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -55,6 +55,7 @@ config DRM_RCAR_MIPI_DSI
 	def_tristate DRM_RCAR_DU
 	depends on DRM_RCAR_USE_MIPI_DSI
 	select DRM_MIPI_DSI
+	select RESET_CONTROLLER
 
 config DRM_RCAR_VSP
 	bool "R-Car DU VSP Compositor Support" if ARM
-- 
2.34.1

[PATCH v3 2/7] drm: rcar-du: lvds: Add runtime PM

[Tomi Valkeinen]

Add simple runtime PM suspend and resume functionality.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/Kconfig     |  1 +
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 43 +++++++++++++++++++++++++----
 2 files changed, 38 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index a8f862c68b4f..17cb98ce7530 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -39,6 +39,7 @@ config DRM_RCAR_USE_LVDS
 config DRM_RCAR_LVDS
 	def_tristate DRM_RCAR_DU
 	depends on DRM_RCAR_USE_LVDS
+	depends on PM
 	select DRM_KMS_HELPER
 	select DRM_PANEL
 	select OF_FLATTREE
diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index 81a060c2fe3f..7cf515e43079 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -16,6 +16,7 @@
 #include <linux/of_device.h>
 #include <linux/of_graph.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 #include <linux/sys_soc.h>
 
@@ -316,8 +317,8 @@ int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq)
 
 	dev_dbg(lvds->dev, "enabling LVDS PLL, freq=%luHz\n", freq);
 
-	ret = clk_prepare_enable(lvds->clocks.mod);
-	if (ret < 0)
+	ret = pm_runtime_resume_and_get(lvds->dev);
+	if (ret)
 		return ret;
 
 	__rcar_lvds_pll_setup_d3_e3(lvds, freq, true);
@@ -337,7 +338,7 @@ void rcar_lvds_pclk_disable(struct drm_bridge *bridge)
 
 	rcar_lvds_write(lvds, LVDPLLCR, 0);
 
-	clk_disable_unprepare(lvds->clocks.mod);
+	pm_runtime_put_sync(lvds->dev);
 }
 EXPORT_SYMBOL_GPL(rcar_lvds_pclk_disable);
 
@@ -396,8 +397,8 @@ static void __rcar_lvds_atomic_enable(struct drm_bridge *bridge,
 	u32 lvdcr0;
 	int ret;
 
-	ret = clk_prepare_enable(lvds->clocks.mod);
-	if (ret < 0)
+	ret = pm_runtime_resume_and_get(lvds->dev);
+	if (ret)
 		return;
 
 	/* Enable the companion LVDS encoder in dual-link mode. */
@@ -551,7 +552,7 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 		lvds->companion->funcs->atomic_disable(lvds->companion,
 						       old_bridge_state);
 
-	clk_disable_unprepare(lvds->clocks.mod);
+	pm_runtime_put_sync(lvds->dev);
 }
 
 static bool rcar_lvds_mode_fixup(struct drm_bridge *bridge,
@@ -844,6 +845,8 @@ static int rcar_lvds_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
+	pm_runtime_enable(&pdev->dev);
+
 	drm_bridge_add(&lvds->bridge);
 
 	return 0;
@@ -855,6 +858,8 @@ static int rcar_lvds_remove(struct platform_device *pdev)
 
 	drm_bridge_remove(&lvds->bridge);
 
+	pm_runtime_disable(&pdev->dev);
+
 	return 0;
 }
 
@@ -913,11 +918,37 @@ static const struct of_device_id rcar_lvds_of_table[] = {
 
 MODULE_DEVICE_TABLE(of, rcar_lvds_of_table);
 
+static int rcar_lvds_runtime_suspend(struct device *dev)
+{
+	struct rcar_lvds *lvds = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(lvds->clocks.mod);
+
+	return 0;
+}
+
+static int rcar_lvds_runtime_resume(struct device *dev)
+{
+	struct rcar_lvds *lvds = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_prepare_enable(lvds->clocks.mod);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static const struct dev_pm_ops rcar_lvds_pm_ops = {
+	SET_RUNTIME_PM_OPS(rcar_lvds_runtime_suspend, rcar_lvds_runtime_resume, NULL)
+};
+
 static struct platform_driver rcar_lvds_platform_driver = {
 	.probe		= rcar_lvds_probe,
 	.remove		= rcar_lvds_remove,
 	.driver		= {
 		.name	= "rcar-lvds",
+		.pm	= &rcar_lvds_pm_ops,
 		.of_match_table = rcar_lvds_of_table,
 	},
 };
-- 
2.34.1

[PATCH v3 2/7] drm: rcar-du: lvds: Add runtime PM

[Tomi Valkeinen]

Add simple runtime PM suspend and resume functionality.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/Kconfig     |  1 +
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 43 +++++++++++++++++++++++++----
 2 files changed, 38 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index a8f862c68b4f..17cb98ce7530 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -39,6 +39,7 @@ config DRM_RCAR_USE_LVDS
 config DRM_RCAR_LVDS
 	def_tristate DRM_RCAR_DU
 	depends on DRM_RCAR_USE_LVDS
+	depends on PM
 	select DRM_KMS_HELPER
 	select DRM_PANEL
 	select OF_FLATTREE
diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index 81a060c2fe3f..7cf515e43079 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -16,6 +16,7 @@
 #include <linux/of_device.h>
 #include <linux/of_graph.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 #include <linux/sys_soc.h>
 
@@ -316,8 +317,8 @@ int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq)
 
 	dev_dbg(lvds->dev, "enabling LVDS PLL, freq=%luHz\n", freq);
 
-	ret = clk_prepare_enable(lvds->clocks.mod);
-	if (ret < 0)
+	ret = pm_runtime_resume_and_get(lvds->dev);
+	if (ret)
 		return ret;
 
 	__rcar_lvds_pll_setup_d3_e3(lvds, freq, true);
@@ -337,7 +338,7 @@ void rcar_lvds_pclk_disable(struct drm_bridge *bridge)
 
 	rcar_lvds_write(lvds, LVDPLLCR, 0);
 
-	clk_disable_unprepare(lvds->clocks.mod);
+	pm_runtime_put_sync(lvds->dev);
 }
 EXPORT_SYMBOL_GPL(rcar_lvds_pclk_disable);
 
@@ -396,8 +397,8 @@ static void __rcar_lvds_atomic_enable(struct drm_bridge *bridge,
 	u32 lvdcr0;
 	int ret;
 
-	ret = clk_prepare_enable(lvds->clocks.mod);
-	if (ret < 0)
+	ret = pm_runtime_resume_and_get(lvds->dev);
+	if (ret)
 		return;
 
 	/* Enable the companion LVDS encoder in dual-link mode. */
@@ -551,7 +552,7 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 		lvds->companion->funcs->atomic_disable(lvds->companion,
 						       old_bridge_state);
 
-	clk_disable_unprepare(lvds->clocks.mod);
+	pm_runtime_put_sync(lvds->dev);
 }
 
 static bool rcar_lvds_mode_fixup(struct drm_bridge *bridge,
@@ -844,6 +845,8 @@ static int rcar_lvds_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
+	pm_runtime_enable(&pdev->dev);
+
 	drm_bridge_add(&lvds->bridge);
 
 	return 0;
@@ -855,6 +858,8 @@ static int rcar_lvds_remove(struct platform_device *pdev)
 
 	drm_bridge_remove(&lvds->bridge);
 
+	pm_runtime_disable(&pdev->dev);
+
 	return 0;
 }
 
@@ -913,11 +918,37 @@ static const struct of_device_id rcar_lvds_of_table[] = {
 
 MODULE_DEVICE_TABLE(of, rcar_lvds_of_table);
 
+static int rcar_lvds_runtime_suspend(struct device *dev)
+{
+	struct rcar_lvds *lvds = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(lvds->clocks.mod);
+
+	return 0;
+}
+
+static int rcar_lvds_runtime_resume(struct device *dev)
+{
+	struct rcar_lvds *lvds = dev_get_drvdata(dev);
+	int ret;
+
+	ret = clk_prepare_enable(lvds->clocks.mod);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static const struct dev_pm_ops rcar_lvds_pm_ops = {
+	SET_RUNTIME_PM_OPS(rcar_lvds_runtime_suspend, rcar_lvds_runtime_resume, NULL)
+};
+
 static struct platform_driver rcar_lvds_platform_driver = {
 	.probe		= rcar_lvds_probe,
 	.remove		= rcar_lvds_remove,
 	.driver		= {
 		.name	= "rcar-lvds",
+		.pm	= &rcar_lvds_pm_ops,
 		.of_match_table = rcar_lvds_of_table,
 	},
 };
-- 
2.34.1

[PATCH v3 3/7] drm: rcar-du: lvds: Add reset control

[Tomi Valkeinen]

Reset LVDS using the reset control as CPG reset/release is required in
the hardware manual sequence.

Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/Kconfig     |  1 +
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 20 +++++++++++++++++++-
 2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index 17cb98ce7530..742f6f2c8de8 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -44,6 +44,7 @@ config DRM_RCAR_LVDS
 	select DRM_PANEL
 	select OF_FLATTREE
 	select OF_OVERLAY
+	select RESET_CONTROLLER
 
 config DRM_RCAR_USE_MIPI_DSI
 	bool "R-Car DU MIPI DSI Encoder Support"
diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index 7cf515e43079..a11201e4d31b 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -17,6 +17,7 @@
 #include <linux/of_graph.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/reset.h>
 #include <linux/slab.h>
 #include <linux/sys_soc.h>
 
@@ -61,6 +62,7 @@ struct rcar_lvds_device_info {
 struct rcar_lvds {
 	struct device *dev;
 	const struct rcar_lvds_device_info *info;
+	struct reset_control *rstc;
 
 	struct drm_bridge bridge;
 
@@ -845,6 +847,11 @@ static int rcar_lvds_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
+	lvds->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(lvds->rstc))
+		return dev_err_probe(&pdev->dev, PTR_ERR(lvds->rstc),
+				     "failed to get cpg reset\n");
+
 	pm_runtime_enable(&pdev->dev);
 
 	drm_bridge_add(&lvds->bridge);
@@ -924,6 +931,8 @@ static int rcar_lvds_runtime_suspend(struct device *dev)
 
 	clk_disable_unprepare(lvds->clocks.mod);
 
+	reset_control_assert(lvds->rstc);
+
 	return 0;
 }
 
@@ -932,11 +941,20 @@ static int rcar_lvds_runtime_resume(struct device *dev)
 	struct rcar_lvds *lvds = dev_get_drvdata(dev);
 	int ret;
 
+	ret = reset_control_deassert(lvds->rstc);
+	if (ret)
+		return ret;
+
 	ret = clk_prepare_enable(lvds->clocks.mod);
 	if (ret < 0)
-		return ret;
+		goto err_reset_assert;
 
 	return 0;
+
+err_reset_assert:
+	reset_control_assert(lvds->rstc);
+
+	return ret;
 }
 
 static const struct dev_pm_ops rcar_lvds_pm_ops = {
-- 
2.34.1

[PATCH v3 3/7] drm: rcar-du: lvds: Add reset control

[Tomi Valkeinen]

Reset LVDS using the reset control as CPG reset/release is required in
the hardware manual sequence.

Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/Kconfig     |  1 +
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 20 +++++++++++++++++++-
 2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/rcar-du/Kconfig b/drivers/gpu/drm/rcar-du/Kconfig
index 17cb98ce7530..742f6f2c8de8 100644
--- a/drivers/gpu/drm/rcar-du/Kconfig
+++ b/drivers/gpu/drm/rcar-du/Kconfig
@@ -44,6 +44,7 @@ config DRM_RCAR_LVDS
 	select DRM_PANEL
 	select OF_FLATTREE
 	select OF_OVERLAY
+	select RESET_CONTROLLER
 
 config DRM_RCAR_USE_MIPI_DSI
 	bool "R-Car DU MIPI DSI Encoder Support"
diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index 7cf515e43079..a11201e4d31b 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -17,6 +17,7 @@
 #include <linux/of_graph.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/reset.h>
 #include <linux/slab.h>
 #include <linux/sys_soc.h>
 
@@ -61,6 +62,7 @@ struct rcar_lvds_device_info {
 struct rcar_lvds {
 	struct device *dev;
 	const struct rcar_lvds_device_info *info;
+	struct reset_control *rstc;
 
 	struct drm_bridge bridge;
 
@@ -845,6 +847,11 @@ static int rcar_lvds_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
+	lvds->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+	if (IS_ERR(lvds->rstc))
+		return dev_err_probe(&pdev->dev, PTR_ERR(lvds->rstc),
+				     "failed to get cpg reset\n");
+
 	pm_runtime_enable(&pdev->dev);
 
 	drm_bridge_add(&lvds->bridge);
@@ -924,6 +931,8 @@ static int rcar_lvds_runtime_suspend(struct device *dev)
 
 	clk_disable_unprepare(lvds->clocks.mod);
 
+	reset_control_assert(lvds->rstc);
+
 	return 0;
 }
 
@@ -932,11 +941,20 @@ static int rcar_lvds_runtime_resume(struct device *dev)
 	struct rcar_lvds *lvds = dev_get_drvdata(dev);
 	int ret;
 
+	ret = reset_control_deassert(lvds->rstc);
+	if (ret)
+		return ret;
+
 	ret = clk_prepare_enable(lvds->clocks.mod);
 	if (ret < 0)
-		return ret;
+		goto err_reset_assert;
 
 	return 0;
+
+err_reset_assert:
+	reset_control_assert(lvds->rstc);
+
+	return ret;
 }
 
 static const struct dev_pm_ops rcar_lvds_pm_ops = {
-- 
2.34.1

[PATCH v3 4/7] drm: rcar-du: lvds: Fix stop sequence

[Tomi Valkeinen]

From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>

According to hardware manual, LVDCR0 register must be cleared bit by bit
when disabling LVDS.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
[tomi.valkeinen: simplified the code a bit]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index a11201e4d31b..8cd86a3d65a5 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -83,6 +83,11 @@ struct rcar_lvds {
 #define bridge_to_rcar_lvds(b) \
 	container_of(b, struct rcar_lvds, bridge)
 
+static u32 rcar_lvds_read(struct rcar_lvds *lvds, u32 reg)
+{
+	return ioread32(lvds->mmio + reg);
+}
+
 static void rcar_lvds_write(struct rcar_lvds *lvds, u32 reg, u32 data)
 {
 	iowrite32(data, lvds->mmio + reg);
@@ -544,6 +549,27 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 				     struct drm_bridge_state *old_bridge_state)
 {
 	struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
+	u32 lvdcr0;
+
+	lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
+
+	lvdcr0 &= ~LVDCR0_LVRES;
+	rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
+		lvdcr0 &= ~LVDCR0_LVEN;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
+		lvdcr0 &= ~LVDCR0_PWD;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
+		lvdcr0 &= ~LVDCR0_PLLON;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
 
 	rcar_lvds_write(lvds, LVDCR0, 0);
 	rcar_lvds_write(lvds, LVDCR1, 0);
-- 
2.34.1

[PATCH v3 4/7] drm: rcar-du: lvds: Fix stop sequence

[Tomi Valkeinen]

From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>

According to hardware manual, LVDCR0 register must be cleared bit by bit
when disabling LVDS.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
[tomi.valkeinen: simplified the code a bit]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index a11201e4d31b..8cd86a3d65a5 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -83,6 +83,11 @@ struct rcar_lvds {
 #define bridge_to_rcar_lvds(b) \
 	container_of(b, struct rcar_lvds, bridge)
 
+static u32 rcar_lvds_read(struct rcar_lvds *lvds, u32 reg)
+{
+	return ioread32(lvds->mmio + reg);
+}
+
 static void rcar_lvds_write(struct rcar_lvds *lvds, u32 reg, u32 data)
 {
 	iowrite32(data, lvds->mmio + reg);
@@ -544,6 +549,27 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 				     struct drm_bridge_state *old_bridge_state)
 {
 	struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
+	u32 lvdcr0;
+
+	lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
+
+	lvdcr0 &= ~LVDCR0_LVRES;
+	rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
+		lvdcr0 &= ~LVDCR0_LVEN;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
+		lvdcr0 &= ~LVDCR0_PWD;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
+		lvdcr0 &= ~LVDCR0_PLLON;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
 
 	rcar_lvds_write(lvds, LVDCR0, 0);
 	rcar_lvds_write(lvds, LVDCR1, 0);
-- 
2.34.1

[PATCH v3 5/7] drm: rcar-du: Add quirk for H3 ES1.x pclk workaround

[Tomi Valkeinen]

rcar_du_crtc.c does a soc_device_match() in
rcar_du_crtc_set_display_timing() to find out if the SoC is H3 ES1.x, and
if so, apply a workaround.

We will need another H3 ES1.x check in the following patch, so rather than
adding more soc_device_match() calls, let's add a rcar_du_device_info
entry for the ES1, and a quirk flag,
RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY, for the workaround.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c |  8 +----
 drivers/gpu/drm/rcar-du/rcar_du_drv.c  | 48 ++++++++++++++++++++++++++
 drivers/gpu/drm/rcar-du/rcar_du_drv.h  |  1 +
 3 files changed, 50 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index 3619e1ddeb62..f2d3266509cc 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -10,7 +10,6 @@
 #include <linux/clk.h>
 #include <linux/mutex.h>
 #include <linux/platform_device.h>
-#include <linux/sys_soc.h>
 
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_helper.h>
@@ -204,11 +203,6 @@ static void rcar_du_escr_divider(struct clk *clk, unsigned long target,
 	}
 }
 
-static const struct soc_device_attribute rcar_du_r8a7795_es1[] = {
-	{ .soc_id = "r8a7795", .revision = "ES1.*" },
-	{ /* sentinel */ }
-};
-
 static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 {
 	const struct drm_display_mode *mode = &rcrtc->crtc.state->adjusted_mode;
@@ -238,7 +232,7 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 		 * no post-divider when a display PLL is present (as shown by
 		 * the workaround breaking HDMI output on M3-W during testing).
 		 */
-		if (soc_device_match(rcar_du_r8a7795_es1)) {
+		if (rcdu->info->quirks & RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY) {
 			target *= 2;
 			div = 1;
 		}
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.c b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
index c7c5217cfc1a..ea3a8cff74b7 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
@@ -16,6 +16,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/slab.h>
+#include <linux/sys_soc.h>
 #include <linux/wait.h>
 
 #include <drm/drm_atomic_helper.h>
@@ -386,6 +387,42 @@ static const struct rcar_du_device_info rcar_du_r8a7795_info = {
 	.dpll_mask =  BIT(2) | BIT(1),
 };
 
+static const struct rcar_du_device_info rcar_du_r8a7795_es1_info = {
+	.gen = 3,
+	.features = RCAR_DU_FEATURE_CRTC_IRQ
+		  | RCAR_DU_FEATURE_CRTC_CLOCK
+		  | RCAR_DU_FEATURE_VSP1_SOURCE
+		  | RCAR_DU_FEATURE_INTERLACED
+		  | RCAR_DU_FEATURE_TVM_SYNC,
+	.quirks = RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY,
+	.channels_mask = BIT(3) | BIT(2) | BIT(1) | BIT(0),
+	.routes = {
+		/*
+		 * R8A7795 has one RGB output, two HDMI outputs and one
+		 * LVDS output.
+		 */
+		[RCAR_DU_OUTPUT_DPAD0] = {
+			.possible_crtcs = BIT(3),
+			.port = 0,
+		},
+		[RCAR_DU_OUTPUT_HDMI0] = {
+			.possible_crtcs = BIT(1),
+			.port = 1,
+		},
+		[RCAR_DU_OUTPUT_HDMI1] = {
+			.possible_crtcs = BIT(2),
+			.port = 2,
+		},
+		[RCAR_DU_OUTPUT_LVDS0] = {
+			.possible_crtcs = BIT(0),
+			.port = 3,
+		},
+	},
+	.num_lvds = 1,
+	.num_rpf = 5,
+	.dpll_mask =  BIT(2) | BIT(1),
+};
+
 static const struct rcar_du_device_info rcar_du_r8a7796_info = {
 	.gen = 3,
 	.features = RCAR_DU_FEATURE_CRTC_IRQ
@@ -576,6 +613,11 @@ static const struct of_device_id rcar_du_of_table[] = {
 
 MODULE_DEVICE_TABLE(of, rcar_du_of_table);
 
+static const struct soc_device_attribute rcar_du_soc_table[] = {
+	{ .soc_id = "r8a7795", .revision = "ES1.*", .data = &rcar_du_r8a7795_es1_info },
+	{ /* sentinel */ }
+};
+
 const char *rcar_du_output_name(enum rcar_du_output output)
 {
 	static const char * const names[] = {
@@ -667,6 +709,7 @@ static void rcar_du_shutdown(struct platform_device *pdev)
 
 static int rcar_du_probe(struct platform_device *pdev)
 {
+	const struct soc_device_attribute *soc_attr;
 	struct rcar_du_device *rcdu;
 	unsigned int mask;
 	int ret;
@@ -681,8 +724,13 @@ static int rcar_du_probe(struct platform_device *pdev)
 		return PTR_ERR(rcdu);
 
 	rcdu->dev = &pdev->dev;
+
 	rcdu->info = of_device_get_match_data(rcdu->dev);
 
+	soc_attr = soc_device_match(rcar_du_soc_table);
+	if (soc_attr)
+		rcdu->info = soc_attr->data;
+
 	platform_set_drvdata(pdev, rcdu);
 
 	/* I/O resources */
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.h b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
index 5cfa2bb7ad93..df87ccab146f 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.h
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
@@ -34,6 +34,7 @@ struct rcar_du_device;
 #define RCAR_DU_FEATURE_NO_BLENDING	BIT(5)	/* PnMR.SPIM does not have ALP nor EOR bits */
 
 #define RCAR_DU_QUIRK_ALIGN_128B	BIT(0)	/* Align pitches to 128 bytes */
+#define RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY BIT(1)	/* H3 ES1 has pclk stability issue */
 
 enum rcar_du_output {
 	RCAR_DU_OUTPUT_DPAD0,
-- 
2.34.1

[PATCH v3 5/7] drm: rcar-du: Add quirk for H3 ES1.x pclk workaround

[Tomi Valkeinen]

rcar_du_crtc.c does a soc_device_match() in
rcar_du_crtc_set_display_timing() to find out if the SoC is H3 ES1.x, and
if so, apply a workaround.

We will need another H3 ES1.x check in the following patch, so rather than
adding more soc_device_match() calls, let's add a rcar_du_device_info
entry for the ES1, and a quirk flag,
RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY, for the workaround.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c |  8 +----
 drivers/gpu/drm/rcar-du/rcar_du_drv.c  | 48 ++++++++++++++++++++++++++
 drivers/gpu/drm/rcar-du/rcar_du_drv.h  |  1 +
 3 files changed, 50 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index 3619e1ddeb62..f2d3266509cc 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -10,7 +10,6 @@
 #include <linux/clk.h>
 #include <linux/mutex.h>
 #include <linux/platform_device.h>
-#include <linux/sys_soc.h>
 
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_helper.h>
@@ -204,11 +203,6 @@ static void rcar_du_escr_divider(struct clk *clk, unsigned long target,
 	}
 }
 
-static const struct soc_device_attribute rcar_du_r8a7795_es1[] = {
-	{ .soc_id = "r8a7795", .revision = "ES1.*" },
-	{ /* sentinel */ }
-};
-
 static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 {
 	const struct drm_display_mode *mode = &rcrtc->crtc.state->adjusted_mode;
@@ -238,7 +232,7 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 		 * no post-divider when a display PLL is present (as shown by
 		 * the workaround breaking HDMI output on M3-W during testing).
 		 */
-		if (soc_device_match(rcar_du_r8a7795_es1)) {
+		if (rcdu->info->quirks & RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY) {
 			target *= 2;
 			div = 1;
 		}
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.c b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
index c7c5217cfc1a..ea3a8cff74b7 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
@@ -16,6 +16,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 #include <linux/slab.h>
+#include <linux/sys_soc.h>
 #include <linux/wait.h>
 
 #include <drm/drm_atomic_helper.h>
@@ -386,6 +387,42 @@ static const struct rcar_du_device_info rcar_du_r8a7795_info = {
 	.dpll_mask =  BIT(2) | BIT(1),
 };
 
+static const struct rcar_du_device_info rcar_du_r8a7795_es1_info = {
+	.gen = 3,
+	.features = RCAR_DU_FEATURE_CRTC_IRQ
+		  | RCAR_DU_FEATURE_CRTC_CLOCK
+		  | RCAR_DU_FEATURE_VSP1_SOURCE
+		  | RCAR_DU_FEATURE_INTERLACED
+		  | RCAR_DU_FEATURE_TVM_SYNC,
+	.quirks = RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY,
+	.channels_mask = BIT(3) | BIT(2) | BIT(1) | BIT(0),
+	.routes = {
+		/*
+		 * R8A7795 has one RGB output, two HDMI outputs and one
+		 * LVDS output.
+		 */
+		[RCAR_DU_OUTPUT_DPAD0] = {
+			.possible_crtcs = BIT(3),
+			.port = 0,
+		},
+		[RCAR_DU_OUTPUT_HDMI0] = {
+			.possible_crtcs = BIT(1),
+			.port = 1,
+		},
+		[RCAR_DU_OUTPUT_HDMI1] = {
+			.possible_crtcs = BIT(2),
+			.port = 2,
+		},
+		[RCAR_DU_OUTPUT_LVDS0] = {
+			.possible_crtcs = BIT(0),
+			.port = 3,
+		},
+	},
+	.num_lvds = 1,
+	.num_rpf = 5,
+	.dpll_mask =  BIT(2) | BIT(1),
+};
+
 static const struct rcar_du_device_info rcar_du_r8a7796_info = {
 	.gen = 3,
 	.features = RCAR_DU_FEATURE_CRTC_IRQ
@@ -576,6 +613,11 @@ static const struct of_device_id rcar_du_of_table[] = {
 
 MODULE_DEVICE_TABLE(of, rcar_du_of_table);
 
+static const struct soc_device_attribute rcar_du_soc_table[] = {
+	{ .soc_id = "r8a7795", .revision = "ES1.*", .data = &rcar_du_r8a7795_es1_info },
+	{ /* sentinel */ }
+};
+
 const char *rcar_du_output_name(enum rcar_du_output output)
 {
 	static const char * const names[] = {
@@ -667,6 +709,7 @@ static void rcar_du_shutdown(struct platform_device *pdev)
 
 static int rcar_du_probe(struct platform_device *pdev)
 {
+	const struct soc_device_attribute *soc_attr;
 	struct rcar_du_device *rcdu;
 	unsigned int mask;
 	int ret;
@@ -681,8 +724,13 @@ static int rcar_du_probe(struct platform_device *pdev)
 		return PTR_ERR(rcdu);
 
 	rcdu->dev = &pdev->dev;
+
 	rcdu->info = of_device_get_match_data(rcdu->dev);
 
+	soc_attr = soc_device_match(rcar_du_soc_table);
+	if (soc_attr)
+		rcdu->info = soc_attr->data;
+
 	platform_set_drvdata(pdev, rcdu);
 
 	/* I/O resources */
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.h b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
index 5cfa2bb7ad93..df87ccab146f 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.h
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
@@ -34,6 +34,7 @@ struct rcar_du_device;
 #define RCAR_DU_FEATURE_NO_BLENDING	BIT(5)	/* PnMR.SPIM does not have ALP nor EOR bits */
 
 #define RCAR_DU_QUIRK_ALIGN_128B	BIT(0)	/* Align pitches to 128 bytes */
+#define RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY BIT(1)	/* H3 ES1 has pclk stability issue */
 
 enum rcar_du_output {
 	RCAR_DU_OUTPUT_DPAD0,
-- 
2.34.1

[PATCH v3 6/7] drm: rcar-du: Fix setting a reserved bit in DPLLCR

[Tomi Valkeinen]

On H3 ES1.x two bits in DPLLCR are used to select the DU input dot clock
source. These are bits 20 and 21 for DU2, and bits 22 and 23 for DU1. On
non-ES1.x, only the higher bits are used (bits 21 and 23), and the lower
bits are reserved and should be set to 0.

The current code always sets the lower bits, even on non-ES1.x.

For both DU1 and DU2, on all SoC versions, when writing zeroes to those
bits the input clock is DCLKIN, and thus there's no difference between
ES1.x and non-ES1.x.

For DU1, writing 0b10 to the bits (or only writing the higher bit)
results in using PLL0 as the input clock, so in this case there's also
no difference between ES1.x and non-ES1.x.

However, for DU2, writing 0b10 to the bits results in using PLL0 as the
input clock on ES1.x, whereas on non-ES1.x it results in using PLL1. On
ES1.x you need to write 0b11 to select PLL1.

The current code always writes 0b11 to PLCS0 field to select PLL1 on all
SoC versions, which works but causes an illegal (in the sense of not
allowed by the documentation) write to a reserved bit field.

To remove the illegal bit write on PLSC0 we need to handle the input dot
clock selection differently for ES1.x and non-ES1.x.

Add a new quirk, RCAR_DU_QUIRK_H3_ES1_PLL, for this. This way we can
always set the bit 21 on PLSC0 when choosing the PLL as the source
clock, and additionally set the bit 20 when on ES1.x.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 23 ++++++++++++++++++++---
 drivers/gpu/drm/rcar-du/rcar_du_drv.c  |  3 ++-
 drivers/gpu/drm/rcar-du/rcar_du_drv.h  |  1 +
 drivers/gpu/drm/rcar-du/rcar_du_regs.h |  8 ++------
 4 files changed, 25 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index f2d3266509cc..b7dd59fe119e 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -245,13 +245,30 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 		       | DPLLCR_N(dpll.n) | DPLLCR_M(dpll.m)
 		       | DPLLCR_STBY;
 
-		if (rcrtc->index == 1)
+		if (rcrtc->index == 1) {
 			dpllcr |= DPLLCR_PLCS1
 			       |  DPLLCR_INCS_DOTCLKIN1;
-		else
-			dpllcr |= DPLLCR_PLCS0
+		} else {
+			dpllcr |= DPLLCR_PLCS0_PLL
 			       |  DPLLCR_INCS_DOTCLKIN0;
 
+			/*
+			 * On ES2.x we have a single mux controlled via bit 21,
+			 * which selects between DCLKIN source (bit 21 = 0) and
+			 * a PLL source (bit 21 = 1), where the PLL is always
+			 * PLL1.
+			 *
+			 * On ES1.x we have an additional mux, controlled
+			 * via bit 20, for choosing between PLL0 (bit 20 = 0)
+			 * and PLL1 (bit 20 = 1). We always want to use PLL1,
+			 * so on ES1.x, in addition to setting bit 21, we need
+			 * to set the bit 20.
+			 */
+
+			if (rcdu->info->quirks & RCAR_DU_QUIRK_H3_ES1_PLL)
+				dpllcr |= DPLLCR_PLCS0_H3ES1X_PLL1;
+		}
+
 		rcar_du_group_write(rcrtc->group, DPLLCR, dpllcr);
 
 		escr = ESCR_DCLKSEL_DCLKIN | div;
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.c b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
index ea3a8cff74b7..82f9718ff500 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
@@ -394,7 +394,8 @@ static const struct rcar_du_device_info rcar_du_r8a7795_es1_info = {
 		  | RCAR_DU_FEATURE_VSP1_SOURCE
 		  | RCAR_DU_FEATURE_INTERLACED
 		  | RCAR_DU_FEATURE_TVM_SYNC,
-	.quirks = RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY,
+	.quirks = RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY
+		| RCAR_DU_QUIRK_H3_ES1_PLL,
 	.channels_mask = BIT(3) | BIT(2) | BIT(1) | BIT(0),
 	.routes = {
 		/*
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.h b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
index df87ccab146f..acc3673fefe1 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.h
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
@@ -35,6 +35,7 @@ struct rcar_du_device;
 
 #define RCAR_DU_QUIRK_ALIGN_128B	BIT(0)	/* Align pitches to 128 bytes */
 #define RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY BIT(1)	/* H3 ES1 has pclk stability issue */
+#define RCAR_DU_QUIRK_H3_ES1_PLL	BIT(2)	/* H3 ES1 PLL setup differs from non-ES1 */
 
 enum rcar_du_output {
 	RCAR_DU_OUTPUT_DPAD0,
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_regs.h b/drivers/gpu/drm/rcar-du/rcar_du_regs.h
index c1bcb0e8b5b4..789ae9285108 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_regs.h
+++ b/drivers/gpu/drm/rcar-du/rcar_du_regs.h
@@ -283,12 +283,8 @@
 #define DPLLCR			0x20044
 #define DPLLCR_CODE		(0x95 << 24)
 #define DPLLCR_PLCS1		(1 << 23)
-/*
- * PLCS0 is bit 21, but H3 ES1.x requires bit 20 to be set as well. As bit 20
- * isn't implemented by other SoC in the Gen3 family it can safely be set
- * unconditionally.
- */
-#define DPLLCR_PLCS0		(3 << 20)
+#define DPLLCR_PLCS0_PLL	(1 << 21)
+#define DPLLCR_PLCS0_H3ES1X_PLL1	(1 << 20)
 #define DPLLCR_CLKE		(1 << 18)
 #define DPLLCR_FDPLL(n)		((n) << 12)
 #define DPLLCR_N(n)		((n) << 5)
-- 
2.34.1

[PATCH v3 6/7] drm: rcar-du: Fix setting a reserved bit in DPLLCR

[Tomi Valkeinen]

On H3 ES1.x two bits in DPLLCR are used to select the DU input dot clock
source. These are bits 20 and 21 for DU2, and bits 22 and 23 for DU1. On
non-ES1.x, only the higher bits are used (bits 21 and 23), and the lower
bits are reserved and should be set to 0.

The current code always sets the lower bits, even on non-ES1.x.

For both DU1 and DU2, on all SoC versions, when writing zeroes to those
bits the input clock is DCLKIN, and thus there's no difference between
ES1.x and non-ES1.x.

For DU1, writing 0b10 to the bits (or only writing the higher bit)
results in using PLL0 as the input clock, so in this case there's also
no difference between ES1.x and non-ES1.x.

However, for DU2, writing 0b10 to the bits results in using PLL0 as the
input clock on ES1.x, whereas on non-ES1.x it results in using PLL1. On
ES1.x you need to write 0b11 to select PLL1.

The current code always writes 0b11 to PLCS0 field to select PLL1 on all
SoC versions, which works but causes an illegal (in the sense of not
allowed by the documentation) write to a reserved bit field.

To remove the illegal bit write on PLSC0 we need to handle the input dot
clock selection differently for ES1.x and non-ES1.x.

Add a new quirk, RCAR_DU_QUIRK_H3_ES1_PLL, for this. This way we can
always set the bit 21 on PLSC0 when choosing the PLL as the source
clock, and additionally set the bit 20 when on ES1.x.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 23 ++++++++++++++++++++---
 drivers/gpu/drm/rcar-du/rcar_du_drv.c  |  3 ++-
 drivers/gpu/drm/rcar-du/rcar_du_drv.h  |  1 +
 drivers/gpu/drm/rcar-du/rcar_du_regs.h |  8 ++------
 4 files changed, 25 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index f2d3266509cc..b7dd59fe119e 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -245,13 +245,30 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 		       | DPLLCR_N(dpll.n) | DPLLCR_M(dpll.m)
 		       | DPLLCR_STBY;
 
-		if (rcrtc->index == 1)
+		if (rcrtc->index == 1) {
 			dpllcr |= DPLLCR_PLCS1
 			       |  DPLLCR_INCS_DOTCLKIN1;
-		else
-			dpllcr |= DPLLCR_PLCS0
+		} else {
+			dpllcr |= DPLLCR_PLCS0_PLL
 			       |  DPLLCR_INCS_DOTCLKIN0;
 
+			/*
+			 * On ES2.x we have a single mux controlled via bit 21,
+			 * which selects between DCLKIN source (bit 21 = 0) and
+			 * a PLL source (bit 21 = 1), where the PLL is always
+			 * PLL1.
+			 *
+			 * On ES1.x we have an additional mux, controlled
+			 * via bit 20, for choosing between PLL0 (bit 20 = 0)
+			 * and PLL1 (bit 20 = 1). We always want to use PLL1,
+			 * so on ES1.x, in addition to setting bit 21, we need
+			 * to set the bit 20.
+			 */
+
+			if (rcdu->info->quirks & RCAR_DU_QUIRK_H3_ES1_PLL)
+				dpllcr |= DPLLCR_PLCS0_H3ES1X_PLL1;
+		}
+
 		rcar_du_group_write(rcrtc->group, DPLLCR, dpllcr);
 
 		escr = ESCR_DCLKSEL_DCLKIN | div;
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.c b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
index ea3a8cff74b7..82f9718ff500 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.c
@@ -394,7 +394,8 @@ static const struct rcar_du_device_info rcar_du_r8a7795_es1_info = {
 		  | RCAR_DU_FEATURE_VSP1_SOURCE
 		  | RCAR_DU_FEATURE_INTERLACED
 		  | RCAR_DU_FEATURE_TVM_SYNC,
-	.quirks = RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY,
+	.quirks = RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY
+		| RCAR_DU_QUIRK_H3_ES1_PLL,
 	.channels_mask = BIT(3) | BIT(2) | BIT(1) | BIT(0),
 	.routes = {
 		/*
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_drv.h b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
index df87ccab146f..acc3673fefe1 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_drv.h
+++ b/drivers/gpu/drm/rcar-du/rcar_du_drv.h
@@ -35,6 +35,7 @@ struct rcar_du_device;
 
 #define RCAR_DU_QUIRK_ALIGN_128B	BIT(0)	/* Align pitches to 128 bytes */
 #define RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY BIT(1)	/* H3 ES1 has pclk stability issue */
+#define RCAR_DU_QUIRK_H3_ES1_PLL	BIT(2)	/* H3 ES1 PLL setup differs from non-ES1 */
 
 enum rcar_du_output {
 	RCAR_DU_OUTPUT_DPAD0,
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_regs.h b/drivers/gpu/drm/rcar-du/rcar_du_regs.h
index c1bcb0e8b5b4..789ae9285108 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_regs.h
+++ b/drivers/gpu/drm/rcar-du/rcar_du_regs.h
@@ -283,12 +283,8 @@
 #define DPLLCR			0x20044
 #define DPLLCR_CODE		(0x95 << 24)
 #define DPLLCR_PLCS1		(1 << 23)
-/*
- * PLCS0 is bit 21, but H3 ES1.x requires bit 20 to be set as well. As bit 20
- * isn't implemented by other SoC in the Gen3 family it can safely be set
- * unconditionally.
- */
-#define DPLLCR_PLCS0		(3 << 20)
+#define DPLLCR_PLCS0_PLL	(1 << 21)
+#define DPLLCR_PLCS0_H3ES1X_PLL1	(1 << 20)
 #define DPLLCR_CLKE		(1 << 18)
 #define DPLLCR_FDPLL(n)		((n) << 12)
 #define DPLLCR_N(n)		((n) << 5)
-- 
2.34.1

[PATCH v3 7/7] drm: rcar-du: Stop accessing non-existant registers on gen4

[Tomi Valkeinen]

The following registers do not exist on gen4, so we should not write
them: DEF6Rm, DEF7Rm, DEF8Rm, ESCRn, OTARn.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c  |  8 +++++---
 drivers/gpu/drm/rcar-du/rcar_du_group.c | 24 ++++++++++++++----------
 2 files changed, 19 insertions(+), 13 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index b7dd59fe119e..008e172ed43b 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -298,10 +298,12 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 		escr = params.escr;
 	}
 
-	dev_dbg(rcrtc->dev->dev, "%s: ESCR 0x%08x\n", __func__, escr);
+	if (rcdu->info->gen < 4) {
+		dev_dbg(rcrtc->dev->dev, "%s: ESCR 0x%08x\n", __func__, escr);
 
-	rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? ESCR13 : ESCR02, escr);
-	rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? OTAR13 : OTAR02, 0);
+		rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? ESCR13 : ESCR02, escr);
+		rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? OTAR13 : OTAR02, 0);
+	}
 
 	/* Signal polarities */
 	dsmr = ((mode->flags & DRM_MODE_FLAG_PVSYNC) ? DSMR_VSL : 0)
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_group.c b/drivers/gpu/drm/rcar-du/rcar_du_group.c
index 6da01760ede5..152602236377 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_group.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_group.c
@@ -148,19 +148,23 @@ static void rcar_du_group_setup(struct rcar_du_group *rgrp)
 	}
 	rcar_du_group_write(rgrp, DEFR5, DEFR5_CODE | DEFR5_DEFE5);
 
-	rcar_du_group_setup_pins(rgrp);
+	if (rcdu->info->gen < 4)
+		rcar_du_group_setup_pins(rgrp);
 
-	/*
-	 * TODO: Handle routing of the DU output to CMM dynamically, as we
-	 * should bypass CMM completely when no color management feature is
-	 * used.
-	 */
-	defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
-		 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
-	rcar_du_group_write(rgrp, DEFR7, defr7);
+	if (rcdu->info->gen < 4) {
+		/*
+		 * TODO: Handle routing of the DU output to CMM dynamically, as
+		 * we should bypass CMM completely when no color management
+		 * feature is used.
+		 */
+		defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
+			 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
+		rcar_du_group_write(rgrp, DEFR7, defr7);
+	}
 
 	if (rcdu->info->gen >= 2) {
-		rcar_du_group_setup_defr8(rgrp);
+		if (rcdu->info->gen < 4)
+			rcar_du_group_setup_defr8(rgrp);
 		rcar_du_group_setup_didsr(rgrp);
 	}
 
-- 
2.34.1

[PATCH v3 7/7] drm: rcar-du: Stop accessing non-existant registers on gen4

[Tomi Valkeinen]

The following registers do not exist on gen4, so we should not write
them: DEF6Rm, DEF7Rm, DEF8Rm, ESCRn, OTARn.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
 drivers/gpu/drm/rcar-du/rcar_du_crtc.c  |  8 +++++---
 drivers/gpu/drm/rcar-du/rcar_du_group.c | 24 ++++++++++++++----------
 2 files changed, 19 insertions(+), 13 deletions(-)

diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index b7dd59fe119e..008e172ed43b 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -298,10 +298,12 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
 		escr = params.escr;
 	}
 
-	dev_dbg(rcrtc->dev->dev, "%s: ESCR 0x%08x\n", __func__, escr);
+	if (rcdu->info->gen < 4) {
+		dev_dbg(rcrtc->dev->dev, "%s: ESCR 0x%08x\n", __func__, escr);
 
-	rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? ESCR13 : ESCR02, escr);
-	rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? OTAR13 : OTAR02, 0);
+		rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? ESCR13 : ESCR02, escr);
+		rcar_du_crtc_write(rcrtc, rcrtc->index % 2 ? OTAR13 : OTAR02, 0);
+	}
 
 	/* Signal polarities */
 	dsmr = ((mode->flags & DRM_MODE_FLAG_PVSYNC) ? DSMR_VSL : 0)
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_group.c b/drivers/gpu/drm/rcar-du/rcar_du_group.c
index 6da01760ede5..152602236377 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_group.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_group.c
@@ -148,19 +148,23 @@ static void rcar_du_group_setup(struct rcar_du_group *rgrp)
 	}
 	rcar_du_group_write(rgrp, DEFR5, DEFR5_CODE | DEFR5_DEFE5);
 
-	rcar_du_group_setup_pins(rgrp);
+	if (rcdu->info->gen < 4)
+		rcar_du_group_setup_pins(rgrp);
 
-	/*
-	 * TODO: Handle routing of the DU output to CMM dynamically, as we
-	 * should bypass CMM completely when no color management feature is
-	 * used.
-	 */
-	defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
-		 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
-	rcar_du_group_write(rgrp, DEFR7, defr7);
+	if (rcdu->info->gen < 4) {
+		/*
+		 * TODO: Handle routing of the DU output to CMM dynamically, as
+		 * we should bypass CMM completely when no color management
+		 * feature is used.
+		 */
+		defr7 |= (rgrp->cmms_mask & BIT(1) ? DEFR7_CMME1 : 0) |
+			 (rgrp->cmms_mask & BIT(0) ? DEFR7_CMME0 : 0);
+		rcar_du_group_write(rgrp, DEFR7, defr7);
+	}
 
 	if (rcdu->info->gen >= 2) {
-		rcar_du_group_setup_defr8(rgrp);
+		if (rcdu->info->gen < 4)
+			rcar_du_group_setup_defr8(rgrp);
 		rcar_du_group_setup_didsr(rgrp);
 	}
 
-- 
2.34.1

Re: [PATCH v3 4/7] drm: rcar-du: lvds: Fix stop sequence

[Geert Uytterhoeven]

Hi Tomi,

On Mon, Jan 23, 2023 at 11:48 AM Tomi Valkeinen
<tomi.valkeinen+renesas@ideasonboard.com> wrote:
> From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
>
> According to hardware manual, LVDCR0 register must be cleared bit by bit
> when disabling LVDS.
>
> Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
> Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
> [tomi.valkeinen: simplified the code a bit]
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Thanks for your patch!

> @@ -544,6 +549,27 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
>                                      struct drm_bridge_state *old_bridge_state)
>  {
>         struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> +       u32 lvdcr0;
> +
> +       lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
> +
> +       lvdcr0 &= ~LVDCR0_LVRES;
> +       rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +
> +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
> +               lvdcr0 &= ~LVDCR0_LVEN;
> +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +       }
> +
> +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
> +               lvdcr0 &= ~LVDCR0_PWD;
> +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +       }
> +
> +       if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> +               lvdcr0 &= ~LVDCR0_PLLON;
> +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +       }

Please add a comment explaining why there are multiple register writes,
to avoid an over-zealous janitor "optimizing" the code later.

>
>         rcar_lvds_write(lvds, LVDCR0, 0);
>         rcar_lvds_write(lvds, LVDCR1, 0);

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v3 4/7] drm: rcar-du: lvds: Fix stop sequence

[Geert Uytterhoeven]

Hi Tomi,

On Mon, Jan 23, 2023 at 11:48 AM Tomi Valkeinen
<tomi.valkeinen+renesas@ideasonboard.com> wrote:
> From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
>
> According to hardware manual, LVDCR0 register must be cleared bit by bit
> when disabling LVDS.
>
> Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
> Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
> [tomi.valkeinen: simplified the code a bit]
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Thanks for your patch!

> @@ -544,6 +549,27 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
>                                      struct drm_bridge_state *old_bridge_state)
>  {
>         struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> +       u32 lvdcr0;
> +
> +       lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
> +
> +       lvdcr0 &= ~LVDCR0_LVRES;
> +       rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +
> +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
> +               lvdcr0 &= ~LVDCR0_LVEN;
> +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +       }
> +
> +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
> +               lvdcr0 &= ~LVDCR0_PWD;
> +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +       }
> +
> +       if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> +               lvdcr0 &= ~LVDCR0_PLLON;
> +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> +       }

Please add a comment explaining why there are multiple register writes,
to avoid an over-zealous janitor "optimizing" the code later.

>
>         rcar_lvds_write(lvds, LVDCR0, 0);
>         rcar_lvds_write(lvds, LVDCR1, 0);

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v3 4/7] drm: rcar-du: lvds: Fix stop sequence

[Laurent Pinchart]

Hi Geert,

On Mon, Jan 23, 2023 at 03:28:08PM +0100, Geert Uytterhoeven wrote:
> On Mon, Jan 23, 2023 at 11:48 AM Tomi Valkeinen wrote:
> > From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
> >
> > According to hardware manual, LVDCR0 register must be cleared bit by bit
> > when disabling LVDS.
> >
> > Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
> > Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
> > [tomi.valkeinen: simplified the code a bit]
> > Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
> > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Thanks for your patch!
> 
> > @@ -544,6 +549,27 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
> >                                      struct drm_bridge_state *old_bridge_state)
> >  {
> >         struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> > +       u32 lvdcr0;
> > +
> > +       lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
> > +
> > +       lvdcr0 &= ~LVDCR0_LVRES;
> > +       rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +
> > +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
> > +               lvdcr0 &= ~LVDCR0_LVEN;
> > +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +       }
> > +
> > +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
> > +               lvdcr0 &= ~LVDCR0_PWD;
> > +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +       }
> > +
> > +       if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> > +               lvdcr0 &= ~LVDCR0_PLLON;
> > +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +       }
> 
> Please add a comment explaining why there are multiple register writes,
> to avoid an over-zealous janitor "optimizing" the code later.

I'll add this comment at the top of the function:

        /*
         * Clear the LVDCR0 bits in the order specified by the hardware
         * documentation, ending with a write of 0 to the full register to
         * clear all remaining bits.
         */

> >
> >         rcar_lvds_write(lvds, LVDCR0, 0);
> >         rcar_lvds_write(lvds, LVDCR1, 0);

-- 
Regards,

Laurent Pinchart

Re: [PATCH v3 4/7] drm: rcar-du: lvds: Fix stop sequence

[Laurent Pinchart]

Hi Geert,

On Mon, Jan 23, 2023 at 03:28:08PM +0100, Geert Uytterhoeven wrote:
> On Mon, Jan 23, 2023 at 11:48 AM Tomi Valkeinen wrote:
> > From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
> >
> > According to hardware manual, LVDCR0 register must be cleared bit by bit
> > when disabling LVDS.
> >
> > Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
> > Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
> > [tomi.valkeinen: simplified the code a bit]
> > Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
> > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> Thanks for your patch!
> 
> > @@ -544,6 +549,27 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
> >                                      struct drm_bridge_state *old_bridge_state)
> >  {
> >         struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> > +       u32 lvdcr0;
> > +
> > +       lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
> > +
> > +       lvdcr0 &= ~LVDCR0_LVRES;
> > +       rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +
> > +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
> > +               lvdcr0 &= ~LVDCR0_LVEN;
> > +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +       }
> > +
> > +       if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
> > +               lvdcr0 &= ~LVDCR0_PWD;
> > +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +       }
> > +
> > +       if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> > +               lvdcr0 &= ~LVDCR0_PLLON;
> > +               rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +       }
> 
> Please add a comment explaining why there are multiple register writes,
> to avoid an over-zealous janitor "optimizing" the code later.

I'll add this comment at the top of the function:

        /*
         * Clear the LVDCR0 bits in the order specified by the hardware
         * documentation, ending with a write of 0 to the full register to
         * clear all remaining bits.
         */

> >
> >         rcar_lvds_write(lvds, LVDCR0, 0);
> >         rcar_lvds_write(lvds, LVDCR1, 0);

-- 
Regards,

Laurent Pinchart

[PATCH v3.1 4/7] drm: rcar-du: lvds: Fix stop sequence

[Laurent Pinchart]

From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>

According to hardware manual, LVDCR0 register must be cleared bit by bit
when disabling LVDS.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
[tomi.valkeinen: simplified the code a bit]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
Changes since v3:

- Add comment explaining the register clear sequence
---
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 31 +++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index a11201e4d31b..260ea5d8624e 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -83,6 +83,11 @@ struct rcar_lvds {
 #define bridge_to_rcar_lvds(b) \
 	container_of(b, struct rcar_lvds, bridge)
 
+static u32 rcar_lvds_read(struct rcar_lvds *lvds, u32 reg)
+{
+	return ioread32(lvds->mmio + reg);
+}
+
 static void rcar_lvds_write(struct rcar_lvds *lvds, u32 reg, u32 data)
 {
 	iowrite32(data, lvds->mmio + reg);
@@ -544,6 +549,32 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 				     struct drm_bridge_state *old_bridge_state)
 {
 	struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
+	u32 lvdcr0;
+
+	/*
+	 * Clear the LVDCR0 bits in the order specified by the hardware
+	 * documentation, ending with a write of 0 to the full register to
+	 * clear all remaining bits.
+	 */
+	lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
+
+	lvdcr0 &= ~LVDCR0_LVRES;
+	rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
+		lvdcr0 &= ~LVDCR0_LVEN;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
+		lvdcr0 &= ~LVDCR0_PWD;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
+		lvdcr0 &= ~LVDCR0_PLLON;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
 
 	rcar_lvds_write(lvds, LVDCR0, 0);
 	rcar_lvds_write(lvds, LVDCR1, 0);
-- 
Regards,

Laurent Pinchart

[PATCH v3.1 4/7] drm: rcar-du: lvds: Fix stop sequence

[Laurent Pinchart]

From: Koji Matsuoka <koji.matsuoka.xm@renesas.com>

According to hardware manual, LVDCR0 register must be cleared bit by bit
when disabling LVDS.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
[tomi.valkeinen: simplified the code a bit]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
Changes since v3:

- Add comment explaining the register clear sequence
---
 drivers/gpu/drm/rcar-du/rcar_lvds.c | 31 +++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
index a11201e4d31b..260ea5d8624e 100644
--- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
+++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
@@ -83,6 +83,11 @@ struct rcar_lvds {
 #define bridge_to_rcar_lvds(b) \
 	container_of(b, struct rcar_lvds, bridge)
 
+static u32 rcar_lvds_read(struct rcar_lvds *lvds, u32 reg)
+{
+	return ioread32(lvds->mmio + reg);
+}
+
 static void rcar_lvds_write(struct rcar_lvds *lvds, u32 reg, u32 data)
 {
 	iowrite32(data, lvds->mmio + reg);
@@ -544,6 +549,32 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
 				     struct drm_bridge_state *old_bridge_state)
 {
 	struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
+	u32 lvdcr0;
+
+	/*
+	 * Clear the LVDCR0 bits in the order specified by the hardware
+	 * documentation, ending with a write of 0 to the full register to
+	 * clear all remaining bits.
+	 */
+	lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
+
+	lvdcr0 &= ~LVDCR0_LVRES;
+	rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
+		lvdcr0 &= ~LVDCR0_LVEN;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
+		lvdcr0 &= ~LVDCR0_PWD;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
+
+	if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
+		lvdcr0 &= ~LVDCR0_PLLON;
+		rcar_lvds_write(lvds, LVDCR0, lvdcr0);
+	}
 
 	rcar_lvds_write(lvds, LVDCR0, 0);
 	rcar_lvds_write(lvds, LVDCR1, 0);
-- 
Regards,

Laurent Pinchart