* [PATCH v2 00/11] soc: qcom: add UCSI function to PMIC GLINK
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong, Rob Herring
The PMIC GLINK interface offers an UCSI endpoint for newer
SoCs, the UCSI exchange is necessary to configure the USB-C
port USB role and altmode on the SM8450 HDK and SM8550 MTP
boards.
Since the DT description is the same, support for SM8350 HDK
is also added.
This patchset focuses on USB and disables altmode support
on those 2 SoCs until DP altmode over the combo phy is
supported.
Depends on PMIC Glink patchset at [1].
[1] https://lore.kernel.org/all/20230130042003.577063-1-quic_bjorande@quicinc.com/
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v2:
- Moved the dwc3 port subnodes to dtsi
- Added SM8350 HDK support
- Added help about ucsi module name
- Added bindings acks
- Fixed sm8550 pmic glink compatible
- Added more description in config update patch
- Link to v1: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v1-0-0b0acfad301e@linaro.org
---
Neil Armstrong (11):
usb: typec: ucsi: add PMIC Glink UCSI driver
dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible
dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible
soc: qcom: pmic_glink: register ucsi aux device
arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
arm64: dts: qcom: sm8350-hdk: add pmic glink node
arm64: dts: qcom: sm8450-hdk: add pmic glink node
arm64: dts: qcom: sm8550-mtp: add pmic glink node
arm64: defconfig: add PMIC GLINK modules
.../bindings/soc/qcom/qcom,pmic-glink.yaml | 2 +
arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++-
arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 ++
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++-
arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 ++
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++-
arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 ++
arch/arm64/configs/defconfig | 4 +
drivers/soc/qcom/pmic_glink.c | 67 ++++-
drivers/usb/typec/ucsi/Kconfig | 10 +
drivers/usb/typec/ucsi/Makefile | 1 +
drivers/usb/typec/ucsi/ucsi_glink.c | 320 +++++++++++++++++++++
12 files changed, 604 insertions(+), 24 deletions(-)
---
base-commit: 2746a238ae3ea7215b3e95b78020a3d72243d55f
change-id: 20230130-topic-sm8450-upstream-pmic-glink-3b3a0b7bcd33
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
^ permalink raw reply [flat|nested] 52+ messages in thread
* [PATCH v2 00/11] soc: qcom: add UCSI function to PMIC GLINK
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong, Rob Herring
The PMIC GLINK interface offers an UCSI endpoint for newer
SoCs, the UCSI exchange is necessary to configure the USB-C
port USB role and altmode on the SM8450 HDK and SM8550 MTP
boards.
Since the DT description is the same, support for SM8350 HDK
is also added.
This patchset focuses on USB and disables altmode support
on those 2 SoCs until DP altmode over the combo phy is
supported.
Depends on PMIC Glink patchset at [1].
[1] https://lore.kernel.org/all/20230130042003.577063-1-quic_bjorande@quicinc.com/
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v2:
- Moved the dwc3 port subnodes to dtsi
- Added SM8350 HDK support
- Added help about ucsi module name
- Added bindings acks
- Fixed sm8550 pmic glink compatible
- Added more description in config update patch
- Link to v1: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v1-0-0b0acfad301e@linaro.org
---
Neil Armstrong (11):
usb: typec: ucsi: add PMIC Glink UCSI driver
dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible
dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible
soc: qcom: pmic_glink: register ucsi aux device
arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
arm64: dts: qcom: sm8350-hdk: add pmic glink node
arm64: dts: qcom: sm8450-hdk: add pmic glink node
arm64: dts: qcom: sm8550-mtp: add pmic glink node
arm64: defconfig: add PMIC GLINK modules
.../bindings/soc/qcom/qcom,pmic-glink.yaml | 2 +
arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++-
arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 ++
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++-
arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 ++
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++-
arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 ++
arch/arm64/configs/defconfig | 4 +
drivers/soc/qcom/pmic_glink.c | 67 ++++-
drivers/usb/typec/ucsi/Kconfig | 10 +
drivers/usb/typec/ucsi/Makefile | 1 +
drivers/usb/typec/ucsi/ucsi_glink.c | 320 +++++++++++++++++++++
12 files changed, 604 insertions(+), 24 deletions(-)
---
base-commit: 2746a238ae3ea7215b3e95b78020a3d72243d55f
change-id: 20230130-topic-sm8450-upstream-pmic-glink-3b3a0b7bcd33
Best regards,
--
Neil Armstrong <neil.armstrong@linaro.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* [PATCH v2 01/11] usb: typec: ucsi: add PMIC Glink UCSI driver
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Introduce the UCSI PMIC Glink aux driver that communicates
with the aDSP firmware with the UCSI protocol which handles
the USB-C Port(s) Power Delivery.
The UCSI messaging is necessary on newer Qualcomm SoCs to
provide USB role switch and altmode notifications.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
drivers/usb/typec/ucsi/Kconfig | 10 ++
drivers/usb/typec/ucsi/Makefile | 1 +
drivers/usb/typec/ucsi/ucsi_glink.c | 320 ++++++++++++++++++++++++++++++++++++
3 files changed, 331 insertions(+)
diff --git a/drivers/usb/typec/ucsi/Kconfig b/drivers/usb/typec/ucsi/Kconfig
index 8f9c4b9f31f7..b3bb0191987e 100644
--- a/drivers/usb/typec/ucsi/Kconfig
+++ b/drivers/usb/typec/ucsi/Kconfig
@@ -58,4 +58,14 @@ config UCSI_STM32G0
To compile the driver as a module, choose M here: the module will be
called ucsi_stm32g0.
+config UCSI_PMIC_GLINK
+ tristate "UCSI Qualcomm PMIC GLINK Interface Driver"
+ depends on QCOM_PMIC_GLINK
+ help
+ This driver enables UCSI support on platforms that expose UCSI
+ interface as PMIC GLINK device.
+
+ To compile the driver as a module, choose M here: the module will be
+ called ucsi_glink.
+
endif
diff --git a/drivers/usb/typec/ucsi/Makefile b/drivers/usb/typec/ucsi/Makefile
index 480d533d762f..77f09e136956 100644
--- a/drivers/usb/typec/ucsi/Makefile
+++ b/drivers/usb/typec/ucsi/Makefile
@@ -18,3 +18,4 @@ endif
obj-$(CONFIG_UCSI_ACPI) += ucsi_acpi.o
obj-$(CONFIG_UCSI_CCG) += ucsi_ccg.o
obj-$(CONFIG_UCSI_STM32G0) += ucsi_stm32g0.o
+obj-$(CONFIG_UCSI_PMIC_GLINK) += ucsi_glink.o
diff --git a/drivers/usb/typec/ucsi/ucsi_glink.c b/drivers/usb/typec/ucsi/ucsi_glink.c
new file mode 100644
index 000000000000..9123f8a571e7
--- /dev/null
+++ b/drivers/usb/typec/ucsi/ucsi_glink.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2023, Linaro Ltd
+ */
+#include <linux/auxiliary_bus.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/mutex.h>
+#include <linux/property.h>
+#include <linux/soc/qcom/pdr.h>
+#include <linux/soc/qcom/pmic_glink.h>
+#include "ucsi.h"
+
+#define UCSI_BUF_SIZE 48
+
+#define MSG_TYPE_REQ_RESP 1
+#define UCSI_BUF_SIZE 48
+
+#define UC_NOTIFY_RECEIVER_UCSI 0x0
+#define UC_UCSI_READ_BUF_REQ 0x11
+#define UC_UCSI_WRITE_BUF_REQ 0x12
+#define UC_UCSI_USBC_NOTIFY_IND 0x13
+
+struct ucsi_read_buf_req_msg {
+ struct pmic_glink_hdr hdr;
+};
+
+struct ucsi_read_buf_resp_msg {
+ struct pmic_glink_hdr hdr;
+ u8 buf[UCSI_BUF_SIZE];
+ u32 ret_code;
+};
+
+struct ucsi_write_buf_req_msg {
+ struct pmic_glink_hdr hdr;
+ u8 buf[UCSI_BUF_SIZE];
+ u32 reserved;
+};
+
+struct ucsi_write_buf_resp_msg {
+ struct pmic_glink_hdr hdr;
+ u32 ret_code;
+};
+
+struct ucsi_notify_ind_msg {
+ struct pmic_glink_hdr hdr;
+ u32 notification;
+ u32 receiver;
+ u32 reserved;
+};
+
+struct pmic_glink_ucsi {
+ struct device *dev;
+
+ struct pmic_glink_client *client;
+
+ struct ucsi *ucsi;
+ struct completion read_ack;
+ struct completion write_ack;
+ struct completion sync_ack;
+ bool sync_pending;
+ struct mutex lock; /* protects concurrent access to PMIC Glink interface */
+
+ int sync_val;
+
+ struct work_struct notify_work;
+ struct work_struct register_work;
+
+ u8 read_buf[UCSI_BUF_SIZE];
+};
+
+static int pmic_glink_ucsi_read(struct ucsi *__ucsi, unsigned int offset,
+ void *val, size_t val_len)
+{
+ struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+ struct ucsi_read_buf_req_msg req = {};
+ unsigned long left;
+ int ret;
+
+ req.hdr.owner = PMIC_GLINK_OWNER_USBC;
+ req.hdr.type = MSG_TYPE_REQ_RESP;
+ req.hdr.opcode = UC_UCSI_READ_BUF_REQ;
+
+ mutex_lock(&ucsi->lock);
+ memset(ucsi->read_buf, 0, sizeof(ucsi->read_buf));
+ reinit_completion(&ucsi->read_ack);
+
+ ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
+ if (ret < 0) {
+ dev_err(ucsi->dev, "failed to send UCSI read request: %d\n", ret);
+ goto out_unlock;
+ }
+
+ left = wait_for_completion_timeout(&ucsi->read_ack, 5 * HZ);
+ if (!left) {
+ dev_err(ucsi->dev, "timeout waiting for UCSI read response\n");
+ ret = -ETIMEDOUT;
+ goto out_unlock;
+ }
+
+ memcpy(val, &ucsi->read_buf[offset], val_len);
+ ret = 0;
+
+out_unlock:
+ mutex_unlock(&ucsi->lock);
+
+ return ret;
+}
+
+static int pmic_glink_ucsi_locked_write(struct pmic_glink_ucsi *ucsi, unsigned int offset,
+ const void *val, size_t val_len)
+{
+ struct ucsi_write_buf_req_msg req = {};
+ unsigned long left;
+ int ret;
+
+ req.hdr.owner = PMIC_GLINK_OWNER_USBC;
+ req.hdr.type = MSG_TYPE_REQ_RESP;
+ req.hdr.opcode = UC_UCSI_WRITE_BUF_REQ;
+ memcpy(&req.buf[offset], val, val_len);
+
+ reinit_completion(&ucsi->write_ack);
+
+ ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
+ if (ret < 0) {
+ dev_err(ucsi->dev, "failed to send UCSI write request: %d\n", ret);
+ return ret;
+ }
+
+ left = wait_for_completion_timeout(&ucsi->write_ack, 5 * HZ);
+ if (!left) {
+ dev_err(ucsi->dev, "timeout waiting for UCSI write response\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int pmic_glink_ucsi_async_write(struct ucsi *__ucsi, unsigned int offset,
+ const void *val, size_t val_len)
+{
+ struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+ int ret;
+
+ mutex_lock(&ucsi->lock);
+ ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
+ mutex_unlock(&ucsi->lock);
+
+ return ret;
+}
+
+static int pmic_glink_ucsi_sync_write(struct ucsi *__ucsi, unsigned int offset,
+ const void *val, size_t val_len)
+{
+ struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+ unsigned long left;
+ int ret;
+
+ /* TOFIX: Downstream forces recipient to CON when UCSI_GET_ALTERNATE_MODES command */
+
+ mutex_lock(&ucsi->lock);
+ ucsi->sync_val = 0;
+ reinit_completion(&ucsi->sync_ack);
+ ucsi->sync_pending = true;
+ ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
+ mutex_unlock(&ucsi->lock);
+
+ left = wait_for_completion_timeout(&ucsi->sync_ack, 5 * HZ);
+ if (!left) {
+ dev_err(ucsi->dev, "timeout waiting for UCSI sync write response\n");
+ ret = -ETIMEDOUT;
+ } else if (ucsi->sync_val) {
+ dev_err(ucsi->dev, "sync write returned: %d\n", ucsi->sync_val);
+ }
+
+ ucsi->sync_pending = false;
+
+ return ret;
+}
+
+static const struct ucsi_operations pmic_glink_ucsi_ops = {
+ .read = pmic_glink_ucsi_read,
+ .sync_write = pmic_glink_ucsi_sync_write,
+ .async_write = pmic_glink_ucsi_async_write
+};
+
+static void pmic_glink_ucsi_read_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
+{
+ const struct ucsi_read_buf_resp_msg *resp = data;
+
+ if (resp->ret_code)
+ return;
+
+ memcpy(ucsi->read_buf, resp->buf, UCSI_BUF_SIZE);
+ complete(&ucsi->read_ack);
+}
+
+static void pmic_glink_ucsi_write_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
+{
+ const struct ucsi_write_buf_resp_msg *resp = data;
+
+ if (resp->ret_code)
+ return;
+
+ ucsi->sync_val = resp->ret_code;
+ complete(&ucsi->write_ack);
+}
+
+static void pmic_glink_ucsi_notify(struct work_struct *work)
+{
+ struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, notify_work);
+ unsigned int con_num;
+ u32 cci;
+ int ret;
+
+ ret = pmic_glink_ucsi_read(ucsi->ucsi, UCSI_CCI, &cci, sizeof(cci));
+ if (ret) {
+ dev_err(ucsi->dev, "failed to read CCI on notification\n");
+ return;
+ }
+
+ con_num = UCSI_CCI_CONNECTOR(cci);
+ if (con_num)
+ ucsi_connector_change(ucsi->ucsi, con_num);
+
+ if (ucsi->sync_pending && cci & UCSI_CCI_BUSY) {
+ ucsi->sync_val = -EBUSY;
+ complete(&ucsi->sync_ack);
+ } else if (ucsi->sync_pending &&
+ (cci & (UCSI_CCI_ACK_COMPLETE | UCSI_CCI_COMMAND_COMPLETE))) {
+ complete(&ucsi->sync_ack);
+ }
+}
+
+static void pmic_glink_ucsi_register(struct work_struct *work)
+{
+ struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, register_work);
+
+ ucsi_register(ucsi->ucsi);
+}
+
+static void pmic_glink_ucsi_callback(const void *data, size_t len, void *priv)
+{
+ struct pmic_glink_ucsi *ucsi = priv;
+ const struct pmic_glink_hdr *hdr = data;
+
+ switch (hdr->opcode) {
+ case UC_UCSI_READ_BUF_REQ:
+ pmic_glink_ucsi_read_ack(ucsi, data, len);
+ break;
+ case UC_UCSI_WRITE_BUF_REQ:
+ pmic_glink_ucsi_write_ack(ucsi, data, len);
+ break;
+ case UC_UCSI_USBC_NOTIFY_IND:
+ schedule_work(&ucsi->notify_work);
+ break;
+ };
+}
+
+static void pmic_glink_ucsi_pdr_notify(void *priv, int state)
+{
+ struct pmic_glink_ucsi *ucsi = priv;
+
+ if (state == SERVREG_SERVICE_STATE_UP)
+ schedule_work(&ucsi->register_work);
+ else if (state == SERVREG_SERVICE_STATE_DOWN)
+ ucsi_unregister(ucsi->ucsi);
+}
+
+static int pmic_glink_ucsi_probe(struct auxiliary_device *adev,
+ const struct auxiliary_device_id *id)
+{
+ struct pmic_glink_ucsi *ucsi;
+ struct device *dev = &adev->dev;
+
+ ucsi = devm_kzalloc(dev, sizeof(*ucsi), GFP_KERNEL);
+ if (!ucsi)
+ return -ENOMEM;
+
+ ucsi->dev = dev;
+ dev_set_drvdata(dev, ucsi);
+
+ INIT_WORK(&ucsi->notify_work, pmic_glink_ucsi_notify);
+ INIT_WORK(&ucsi->register_work, pmic_glink_ucsi_register);
+ init_completion(&ucsi->read_ack);
+ init_completion(&ucsi->write_ack);
+ init_completion(&ucsi->sync_ack);
+ mutex_init(&ucsi->lock);
+
+ ucsi->ucsi = ucsi_create(dev, &pmic_glink_ucsi_ops);
+ if (IS_ERR(ucsi->ucsi))
+ return PTR_ERR(ucsi->ucsi);
+
+ ucsi_set_drvdata(ucsi->ucsi, ucsi);
+
+ ucsi->client = devm_pmic_glink_register_client(dev,
+ PMIC_GLINK_OWNER_USBC,
+ pmic_glink_ucsi_callback,
+ pmic_glink_ucsi_pdr_notify,
+ ucsi);
+ return PTR_ERR_OR_ZERO(ucsi->client);
+}
+
+static const struct auxiliary_device_id pmic_glink_ucsi_id_table[] = {
+ { .name = "pmic_glink.ucsi", },
+ {},
+};
+MODULE_DEVICE_TABLE(auxiliary, pmic_glink_ucsi_id_table);
+
+static struct auxiliary_driver pmic_glink_ucsi_driver = {
+ .name = "pmic_glink_ucsi",
+ .probe = pmic_glink_ucsi_probe,
+ .id_table = pmic_glink_ucsi_id_table,
+};
+
+module_auxiliary_driver(pmic_glink_ucsi_driver);
+
+MODULE_DESCRIPTION("Qualcomm PMIC GLINK UCSI driver");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 01/11] usb: typec: ucsi: add PMIC Glink UCSI driver
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Introduce the UCSI PMIC Glink aux driver that communicates
with the aDSP firmware with the UCSI protocol which handles
the USB-C Port(s) Power Delivery.
The UCSI messaging is necessary on newer Qualcomm SoCs to
provide USB role switch and altmode notifications.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
drivers/usb/typec/ucsi/Kconfig | 10 ++
drivers/usb/typec/ucsi/Makefile | 1 +
drivers/usb/typec/ucsi/ucsi_glink.c | 320 ++++++++++++++++++++++++++++++++++++
3 files changed, 331 insertions(+)
diff --git a/drivers/usb/typec/ucsi/Kconfig b/drivers/usb/typec/ucsi/Kconfig
index 8f9c4b9f31f7..b3bb0191987e 100644
--- a/drivers/usb/typec/ucsi/Kconfig
+++ b/drivers/usb/typec/ucsi/Kconfig
@@ -58,4 +58,14 @@ config UCSI_STM32G0
To compile the driver as a module, choose M here: the module will be
called ucsi_stm32g0.
+config UCSI_PMIC_GLINK
+ tristate "UCSI Qualcomm PMIC GLINK Interface Driver"
+ depends on QCOM_PMIC_GLINK
+ help
+ This driver enables UCSI support on platforms that expose UCSI
+ interface as PMIC GLINK device.
+
+ To compile the driver as a module, choose M here: the module will be
+ called ucsi_glink.
+
endif
diff --git a/drivers/usb/typec/ucsi/Makefile b/drivers/usb/typec/ucsi/Makefile
index 480d533d762f..77f09e136956 100644
--- a/drivers/usb/typec/ucsi/Makefile
+++ b/drivers/usb/typec/ucsi/Makefile
@@ -18,3 +18,4 @@ endif
obj-$(CONFIG_UCSI_ACPI) += ucsi_acpi.o
obj-$(CONFIG_UCSI_CCG) += ucsi_ccg.o
obj-$(CONFIG_UCSI_STM32G0) += ucsi_stm32g0.o
+obj-$(CONFIG_UCSI_PMIC_GLINK) += ucsi_glink.o
diff --git a/drivers/usb/typec/ucsi/ucsi_glink.c b/drivers/usb/typec/ucsi/ucsi_glink.c
new file mode 100644
index 000000000000..9123f8a571e7
--- /dev/null
+++ b/drivers/usb/typec/ucsi/ucsi_glink.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2023, Linaro Ltd
+ */
+#include <linux/auxiliary_bus.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/mutex.h>
+#include <linux/property.h>
+#include <linux/soc/qcom/pdr.h>
+#include <linux/soc/qcom/pmic_glink.h>
+#include "ucsi.h"
+
+#define UCSI_BUF_SIZE 48
+
+#define MSG_TYPE_REQ_RESP 1
+#define UCSI_BUF_SIZE 48
+
+#define UC_NOTIFY_RECEIVER_UCSI 0x0
+#define UC_UCSI_READ_BUF_REQ 0x11
+#define UC_UCSI_WRITE_BUF_REQ 0x12
+#define UC_UCSI_USBC_NOTIFY_IND 0x13
+
+struct ucsi_read_buf_req_msg {
+ struct pmic_glink_hdr hdr;
+};
+
+struct ucsi_read_buf_resp_msg {
+ struct pmic_glink_hdr hdr;
+ u8 buf[UCSI_BUF_SIZE];
+ u32 ret_code;
+};
+
+struct ucsi_write_buf_req_msg {
+ struct pmic_glink_hdr hdr;
+ u8 buf[UCSI_BUF_SIZE];
+ u32 reserved;
+};
+
+struct ucsi_write_buf_resp_msg {
+ struct pmic_glink_hdr hdr;
+ u32 ret_code;
+};
+
+struct ucsi_notify_ind_msg {
+ struct pmic_glink_hdr hdr;
+ u32 notification;
+ u32 receiver;
+ u32 reserved;
+};
+
+struct pmic_glink_ucsi {
+ struct device *dev;
+
+ struct pmic_glink_client *client;
+
+ struct ucsi *ucsi;
+ struct completion read_ack;
+ struct completion write_ack;
+ struct completion sync_ack;
+ bool sync_pending;
+ struct mutex lock; /* protects concurrent access to PMIC Glink interface */
+
+ int sync_val;
+
+ struct work_struct notify_work;
+ struct work_struct register_work;
+
+ u8 read_buf[UCSI_BUF_SIZE];
+};
+
+static int pmic_glink_ucsi_read(struct ucsi *__ucsi, unsigned int offset,
+ void *val, size_t val_len)
+{
+ struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+ struct ucsi_read_buf_req_msg req = {};
+ unsigned long left;
+ int ret;
+
+ req.hdr.owner = PMIC_GLINK_OWNER_USBC;
+ req.hdr.type = MSG_TYPE_REQ_RESP;
+ req.hdr.opcode = UC_UCSI_READ_BUF_REQ;
+
+ mutex_lock(&ucsi->lock);
+ memset(ucsi->read_buf, 0, sizeof(ucsi->read_buf));
+ reinit_completion(&ucsi->read_ack);
+
+ ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
+ if (ret < 0) {
+ dev_err(ucsi->dev, "failed to send UCSI read request: %d\n", ret);
+ goto out_unlock;
+ }
+
+ left = wait_for_completion_timeout(&ucsi->read_ack, 5 * HZ);
+ if (!left) {
+ dev_err(ucsi->dev, "timeout waiting for UCSI read response\n");
+ ret = -ETIMEDOUT;
+ goto out_unlock;
+ }
+
+ memcpy(val, &ucsi->read_buf[offset], val_len);
+ ret = 0;
+
+out_unlock:
+ mutex_unlock(&ucsi->lock);
+
+ return ret;
+}
+
+static int pmic_glink_ucsi_locked_write(struct pmic_glink_ucsi *ucsi, unsigned int offset,
+ const void *val, size_t val_len)
+{
+ struct ucsi_write_buf_req_msg req = {};
+ unsigned long left;
+ int ret;
+
+ req.hdr.owner = PMIC_GLINK_OWNER_USBC;
+ req.hdr.type = MSG_TYPE_REQ_RESP;
+ req.hdr.opcode = UC_UCSI_WRITE_BUF_REQ;
+ memcpy(&req.buf[offset], val, val_len);
+
+ reinit_completion(&ucsi->write_ack);
+
+ ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
+ if (ret < 0) {
+ dev_err(ucsi->dev, "failed to send UCSI write request: %d\n", ret);
+ return ret;
+ }
+
+ left = wait_for_completion_timeout(&ucsi->write_ack, 5 * HZ);
+ if (!left) {
+ dev_err(ucsi->dev, "timeout waiting for UCSI write response\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int pmic_glink_ucsi_async_write(struct ucsi *__ucsi, unsigned int offset,
+ const void *val, size_t val_len)
+{
+ struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+ int ret;
+
+ mutex_lock(&ucsi->lock);
+ ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
+ mutex_unlock(&ucsi->lock);
+
+ return ret;
+}
+
+static int pmic_glink_ucsi_sync_write(struct ucsi *__ucsi, unsigned int offset,
+ const void *val, size_t val_len)
+{
+ struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+ unsigned long left;
+ int ret;
+
+ /* TOFIX: Downstream forces recipient to CON when UCSI_GET_ALTERNATE_MODES command */
+
+ mutex_lock(&ucsi->lock);
+ ucsi->sync_val = 0;
+ reinit_completion(&ucsi->sync_ack);
+ ucsi->sync_pending = true;
+ ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
+ mutex_unlock(&ucsi->lock);
+
+ left = wait_for_completion_timeout(&ucsi->sync_ack, 5 * HZ);
+ if (!left) {
+ dev_err(ucsi->dev, "timeout waiting for UCSI sync write response\n");
+ ret = -ETIMEDOUT;
+ } else if (ucsi->sync_val) {
+ dev_err(ucsi->dev, "sync write returned: %d\n", ucsi->sync_val);
+ }
+
+ ucsi->sync_pending = false;
+
+ return ret;
+}
+
+static const struct ucsi_operations pmic_glink_ucsi_ops = {
+ .read = pmic_glink_ucsi_read,
+ .sync_write = pmic_glink_ucsi_sync_write,
+ .async_write = pmic_glink_ucsi_async_write
+};
+
+static void pmic_glink_ucsi_read_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
+{
+ const struct ucsi_read_buf_resp_msg *resp = data;
+
+ if (resp->ret_code)
+ return;
+
+ memcpy(ucsi->read_buf, resp->buf, UCSI_BUF_SIZE);
+ complete(&ucsi->read_ack);
+}
+
+static void pmic_glink_ucsi_write_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
+{
+ const struct ucsi_write_buf_resp_msg *resp = data;
+
+ if (resp->ret_code)
+ return;
+
+ ucsi->sync_val = resp->ret_code;
+ complete(&ucsi->write_ack);
+}
+
+static void pmic_glink_ucsi_notify(struct work_struct *work)
+{
+ struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, notify_work);
+ unsigned int con_num;
+ u32 cci;
+ int ret;
+
+ ret = pmic_glink_ucsi_read(ucsi->ucsi, UCSI_CCI, &cci, sizeof(cci));
+ if (ret) {
+ dev_err(ucsi->dev, "failed to read CCI on notification\n");
+ return;
+ }
+
+ con_num = UCSI_CCI_CONNECTOR(cci);
+ if (con_num)
+ ucsi_connector_change(ucsi->ucsi, con_num);
+
+ if (ucsi->sync_pending && cci & UCSI_CCI_BUSY) {
+ ucsi->sync_val = -EBUSY;
+ complete(&ucsi->sync_ack);
+ } else if (ucsi->sync_pending &&
+ (cci & (UCSI_CCI_ACK_COMPLETE | UCSI_CCI_COMMAND_COMPLETE))) {
+ complete(&ucsi->sync_ack);
+ }
+}
+
+static void pmic_glink_ucsi_register(struct work_struct *work)
+{
+ struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, register_work);
+
+ ucsi_register(ucsi->ucsi);
+}
+
+static void pmic_glink_ucsi_callback(const void *data, size_t len, void *priv)
+{
+ struct pmic_glink_ucsi *ucsi = priv;
+ const struct pmic_glink_hdr *hdr = data;
+
+ switch (hdr->opcode) {
+ case UC_UCSI_READ_BUF_REQ:
+ pmic_glink_ucsi_read_ack(ucsi, data, len);
+ break;
+ case UC_UCSI_WRITE_BUF_REQ:
+ pmic_glink_ucsi_write_ack(ucsi, data, len);
+ break;
+ case UC_UCSI_USBC_NOTIFY_IND:
+ schedule_work(&ucsi->notify_work);
+ break;
+ };
+}
+
+static void pmic_glink_ucsi_pdr_notify(void *priv, int state)
+{
+ struct pmic_glink_ucsi *ucsi = priv;
+
+ if (state == SERVREG_SERVICE_STATE_UP)
+ schedule_work(&ucsi->register_work);
+ else if (state == SERVREG_SERVICE_STATE_DOWN)
+ ucsi_unregister(ucsi->ucsi);
+}
+
+static int pmic_glink_ucsi_probe(struct auxiliary_device *adev,
+ const struct auxiliary_device_id *id)
+{
+ struct pmic_glink_ucsi *ucsi;
+ struct device *dev = &adev->dev;
+
+ ucsi = devm_kzalloc(dev, sizeof(*ucsi), GFP_KERNEL);
+ if (!ucsi)
+ return -ENOMEM;
+
+ ucsi->dev = dev;
+ dev_set_drvdata(dev, ucsi);
+
+ INIT_WORK(&ucsi->notify_work, pmic_glink_ucsi_notify);
+ INIT_WORK(&ucsi->register_work, pmic_glink_ucsi_register);
+ init_completion(&ucsi->read_ack);
+ init_completion(&ucsi->write_ack);
+ init_completion(&ucsi->sync_ack);
+ mutex_init(&ucsi->lock);
+
+ ucsi->ucsi = ucsi_create(dev, &pmic_glink_ucsi_ops);
+ if (IS_ERR(ucsi->ucsi))
+ return PTR_ERR(ucsi->ucsi);
+
+ ucsi_set_drvdata(ucsi->ucsi, ucsi);
+
+ ucsi->client = devm_pmic_glink_register_client(dev,
+ PMIC_GLINK_OWNER_USBC,
+ pmic_glink_ucsi_callback,
+ pmic_glink_ucsi_pdr_notify,
+ ucsi);
+ return PTR_ERR_OR_ZERO(ucsi->client);
+}
+
+static const struct auxiliary_device_id pmic_glink_ucsi_id_table[] = {
+ { .name = "pmic_glink.ucsi", },
+ {},
+};
+MODULE_DEVICE_TABLE(auxiliary, pmic_glink_ucsi_id_table);
+
+static struct auxiliary_driver pmic_glink_ucsi_driver = {
+ .name = "pmic_glink_ucsi",
+ .probe = pmic_glink_ucsi_probe,
+ .id_table = pmic_glink_ucsi_id_table,
+};
+
+module_auxiliary_driver(pmic_glink_ucsi_driver);
+
+MODULE_DESCRIPTION("Qualcomm PMIC GLINK UCSI driver");
+MODULE_LICENSE("GPL");
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 02/11] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong, Rob Herring
Document the SM8450 compatible used to describe the pmic glink
on this platform.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
index cf863683c21a..a85bc14de065 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -25,6 +25,7 @@ properties:
- qcom,sc8180x-pmic-glink
- qcom,sc8280xp-pmic-glink
- qcom,sm8350-pmic-glink
+ - qcom,sm8450-pmic-glink
- const: qcom,pmic-glink
'#address-cells':
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 02/11] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong, Rob Herring
Document the SM8450 compatible used to describe the pmic glink
on this platform.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
index cf863683c21a..a85bc14de065 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -25,6 +25,7 @@ properties:
- qcom,sc8180x-pmic-glink
- qcom,sc8280xp-pmic-glink
- qcom,sm8350-pmic-glink
+ - qcom,sm8450-pmic-glink
- const: qcom,pmic-glink
'#address-cells':
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 03/11] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong, Rob Herring
Document the SM8550 compatible used to describe the pmic glink
on this platform.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
index a85bc14de065..6440dc801387 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -26,6 +26,7 @@ properties:
- qcom,sc8280xp-pmic-glink
- qcom,sm8350-pmic-glink
- qcom,sm8450-pmic-glink
+ - qcom,sm8550-pmic-glink
- const: qcom,pmic-glink
'#address-cells':
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 03/11] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong, Rob Herring
Document the SM8550 compatible used to describe the pmic glink
on this platform.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
index a85bc14de065..6440dc801387 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -26,6 +26,7 @@ properties:
- qcom,sc8280xp-pmic-glink
- qcom,sm8350-pmic-glink
- qcom,sm8450-pmic-glink
+ - qcom,sm8550-pmic-glink
- const: qcom,pmic-glink
'#address-cells':
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Only register UCSI on know working devices, like on the SM8450
or Sm8550 which requires UCSI to get USB mode switch events.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
drivers/soc/qcom/pmic_glink.c | 67 ++++++++++++++++++++++++++++++++++++-------
1 file changed, 57 insertions(+), 10 deletions(-)
diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
index bb3fb57abcc6..c7f091f4a8c1 100644
--- a/drivers/soc/qcom/pmic_glink.c
+++ b/drivers/soc/qcom/pmic_glink.c
@@ -4,6 +4,7 @@
* Copyright (c) 2022, Linaro Ltd
*/
#include <linux/auxiliary_bus.h>
+#include <linux/of_device.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/rpmsg.h>
@@ -11,12 +12,23 @@
#include <linux/soc/qcom/pdr.h>
#include <linux/soc/qcom/pmic_glink.h>
+enum {
+ PMIC_GLINK_CLIENT_BATT = 0,
+ PMIC_GLINK_CLIENT_ALTMODE,
+ PMIC_GLINK_CLIENT_UCSI,
+};
+
+#define PMIC_GLINK_CLIENT_DEFAULT (BIT(PMIC_GLINK_CLIENT_BATT) | \
+ BIT(PMIC_GLINK_CLIENT_ALTMODE))
+
struct pmic_glink {
struct device *dev;
struct pdr_handle *pdr;
struct rpmsg_endpoint *ept;
+ unsigned int client_mask;
+
struct auxiliary_device altmode_aux;
struct auxiliary_device ps_aux;
struct auxiliary_device ucsi_aux;
@@ -231,8 +243,19 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
},
};
+/* Do not handle altmode for now on those platforms */
+static const unsigned int pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
+ BIT(PMIC_GLINK_CLIENT_UCSI);
+
+static const struct of_device_id pmic_glink_of_client_mask[] = {
+ { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
+ { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
+ {}
+};
+
static int pmic_glink_probe(struct platform_device *pdev)
{
+ const struct of_device_id *match;
struct pdr_service *service;
struct pmic_glink *pg;
int ret;
@@ -249,12 +272,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
mutex_init(&pg->client_lock);
mutex_init(&pg->state_lock);
- ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
- if (ret)
- return ret;
- ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
- if (ret)
- goto out_release_altmode_aux;
+ match = of_match_device(pmic_glink_of_client_mask, &pdev->dev);
+ if (match)
+ pg->client_mask = *(const unsigned int *)match->data;
+ else
+ pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
+
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
+ ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
+ if (ret)
+ return ret;
+ }
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
+ ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
+ if (ret)
+ goto out_release_ucsi_aux;
+ }
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
+ ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
+ if (ret)
+ goto out_release_altmode_aux;
+ }
pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
if (IS_ERR(pg->pdr)) {
@@ -278,9 +316,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
out_release_pdr_handle:
pdr_handle_release(pg->pdr);
out_release_aux_devices:
- pmic_glink_del_aux_device(pg, &pg->ps_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
+ pmic_glink_del_aux_device(pg, &pg->ps_aux);
out_release_altmode_aux:
- pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
+ pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+out_release_ucsi_aux:
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
+ pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
return ret;
}
@@ -291,8 +334,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
pdr_handle_release(pg->pdr);
- pmic_glink_del_aux_device(pg, &pg->ps_aux);
- pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
+ pmic_glink_del_aux_device(pg, &pg->ps_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
+ pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
+ pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
mutex_lock(&__pmic_glink_lock);
__pmic_glink = NULL;
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Only register UCSI on know working devices, like on the SM8450
or Sm8550 which requires UCSI to get USB mode switch events.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
drivers/soc/qcom/pmic_glink.c | 67 ++++++++++++++++++++++++++++++++++++-------
1 file changed, 57 insertions(+), 10 deletions(-)
diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
index bb3fb57abcc6..c7f091f4a8c1 100644
--- a/drivers/soc/qcom/pmic_glink.c
+++ b/drivers/soc/qcom/pmic_glink.c
@@ -4,6 +4,7 @@
* Copyright (c) 2022, Linaro Ltd
*/
#include <linux/auxiliary_bus.h>
+#include <linux/of_device.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/rpmsg.h>
@@ -11,12 +12,23 @@
#include <linux/soc/qcom/pdr.h>
#include <linux/soc/qcom/pmic_glink.h>
+enum {
+ PMIC_GLINK_CLIENT_BATT = 0,
+ PMIC_GLINK_CLIENT_ALTMODE,
+ PMIC_GLINK_CLIENT_UCSI,
+};
+
+#define PMIC_GLINK_CLIENT_DEFAULT (BIT(PMIC_GLINK_CLIENT_BATT) | \
+ BIT(PMIC_GLINK_CLIENT_ALTMODE))
+
struct pmic_glink {
struct device *dev;
struct pdr_handle *pdr;
struct rpmsg_endpoint *ept;
+ unsigned int client_mask;
+
struct auxiliary_device altmode_aux;
struct auxiliary_device ps_aux;
struct auxiliary_device ucsi_aux;
@@ -231,8 +243,19 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
},
};
+/* Do not handle altmode for now on those platforms */
+static const unsigned int pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
+ BIT(PMIC_GLINK_CLIENT_UCSI);
+
+static const struct of_device_id pmic_glink_of_client_mask[] = {
+ { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
+ { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
+ {}
+};
+
static int pmic_glink_probe(struct platform_device *pdev)
{
+ const struct of_device_id *match;
struct pdr_service *service;
struct pmic_glink *pg;
int ret;
@@ -249,12 +272,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
mutex_init(&pg->client_lock);
mutex_init(&pg->state_lock);
- ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
- if (ret)
- return ret;
- ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
- if (ret)
- goto out_release_altmode_aux;
+ match = of_match_device(pmic_glink_of_client_mask, &pdev->dev);
+ if (match)
+ pg->client_mask = *(const unsigned int *)match->data;
+ else
+ pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
+
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
+ ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
+ if (ret)
+ return ret;
+ }
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
+ ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
+ if (ret)
+ goto out_release_ucsi_aux;
+ }
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
+ ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
+ if (ret)
+ goto out_release_altmode_aux;
+ }
pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
if (IS_ERR(pg->pdr)) {
@@ -278,9 +316,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
out_release_pdr_handle:
pdr_handle_release(pg->pdr);
out_release_aux_devices:
- pmic_glink_del_aux_device(pg, &pg->ps_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
+ pmic_glink_del_aux_device(pg, &pg->ps_aux);
out_release_altmode_aux:
- pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
+ pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+out_release_ucsi_aux:
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
+ pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
return ret;
}
@@ -291,8 +334,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
pdr_handle_release(pg->pdr);
- pmic_glink_del_aux_device(pg, &pg->ps_aux);
- pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
+ pmic_glink_del_aux_device(pg, &pg->ps_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
+ pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+ if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
+ pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
mutex_lock(&__pmic_glink_lock);
__pmic_glink = NULL;
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 05/11] arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 0a422637b61f..3f4631e06187 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -2727,6 +2727,25 @@ usb_1_dwc3: usb@a600000 {
snps,dis_enblslpm_quirk;
phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
phy-names = "usb2-phy", "usb3-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ };
+ };
+ };
};
};
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 05/11] arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 0a422637b61f..3f4631e06187 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -2727,6 +2727,25 @@ usb_1_dwc3: usb@a600000 {
snps,dis_enblslpm_quirk;
phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
phy-names = "usb2-phy", "usb3-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ };
+ };
+ };
};
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 06/11] arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 1a744a33bcf4..ccda73426ee2 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -4155,6 +4155,25 @@ usb_1_dwc3: usb@a600000 {
snps,dis_enblslpm_quirk;
phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
phy-names = "usb2-phy", "usb3-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ };
+ };
+ };
};
};
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 06/11] arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 1a744a33bcf4..ccda73426ee2 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -4155,6 +4155,25 @@ usb_1_dwc3: usb@a600000 {
snps,dis_enblslpm_quirk;
phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
phy-names = "usb2-phy", "usb3-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ };
+ };
+ };
};
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 07/11] arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 9910006c32aa..2914a12a1c89 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -2469,6 +2469,25 @@ usb_1_dwc3: usb@a600000 {
phys = <&usb_1_hsphy>,
<&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
phy-names = "usb2-phy", "usb3-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ };
+ };
+ };
};
};
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 07/11] arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 9910006c32aa..2914a12a1c89 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -2469,6 +2469,25 @@ usb_1_dwc3: usb@a600000 {
phys = <&usb_1_hsphy>,
<&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
phy-names = "usb2-phy", "usb3-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ };
+ };
+ };
};
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
1 file changed, 65 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index 54654eb75c28..28fc9a835c5d 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -31,6 +31,40 @@ hdmi_con: endpoint {
};
};
+ pmic-glink {
+ compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -666,23 +700,42 @@ &usb_1 {
};
&usb_1_dwc3 {
- /* TODO: Define USB-C connector properly */
- dr_mode = "peripheral";
-};
+ dr_mode = "otg";
+ usb-role-switch;
-&usb_1_hsphy {
- status = "okay";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- vdda-pll-supply = <&vreg_l5b_0p88>;
- vdda18-supply = <&vreg_l1c_1p8>;
- vdda33-supply = <&vreg_l2b_3p07>;
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ remote-endpoint = <&pmic_glink_hs_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ remote-endpoint = <&pmic_glink_ss_in>;
+ };
+ };
+ };
};
-&usb_1_qmpphy {
- status = "okay";
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
- vdda-phy-supply = <&vreg_l6b_1p2>;
- vdda-pll-supply = <&vreg_l1b_0p88>;
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_2 {
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
1 file changed, 65 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index 54654eb75c28..28fc9a835c5d 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -31,6 +31,40 @@ hdmi_con: endpoint {
};
};
+ pmic-glink {
+ compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -666,23 +700,42 @@ &usb_1 {
};
&usb_1_dwc3 {
- /* TODO: Define USB-C connector properly */
- dr_mode = "peripheral";
-};
+ dr_mode = "otg";
+ usb-role-switch;
-&usb_1_hsphy {
- status = "okay";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
- vdda-pll-supply = <&vreg_l5b_0p88>;
- vdda18-supply = <&vreg_l1c_1p8>;
- vdda33-supply = <&vreg_l2b_3p07>;
+ port@0 {
+ reg = <0>;
+
+ usb_1_dwc3_hs: endpoint {
+ remote-endpoint = <&pmic_glink_hs_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_1_dwc3_ss: endpoint {
+ remote-endpoint = <&pmic_glink_ss_in>;
+ };
+ };
+ };
};
-&usb_1_qmpphy {
- status = "okay";
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
- vdda-phy-supply = <&vreg_l6b_1p2>;
- vdda-pll-supply = <&vreg_l1b_0p88>;
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_2 {
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 09/11] arm64: dts: qcom: sm8450-hdk: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++++++++++++++++++++++++++++++++-
1 file changed, 44 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index feef3837e4cd..1755ee3aa04c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -87,6 +87,40 @@ lt9611_3v3: lt9611-3v3-regulator {
enable-active-high;
};
+ pmic-glink {
+ compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -724,7 +758,16 @@ &usb_1 {
};
&usb_1_dwc3 {
- dr_mode = "peripheral";
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_1_hsphy {
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 09/11] arm64: dts: qcom: sm8450-hdk: add pmic glink node
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++++++++++++++++++++++++++++++++-
1 file changed, 44 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index feef3837e4cd..1755ee3aa04c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -87,6 +87,40 @@ lt9611_3v3: lt9611-3v3-regulator {
enable-active-high;
};
+ pmic-glink {
+ compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -724,7 +758,16 @@ &usb_1 {
};
&usb_1_dwc3 {
- dr_mode = "peripheral";
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_1_hsphy {
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 10/11] arm64: dts: qcom: sm8550-mtp: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++++++++++++++++++++++++++++++++-
1 file changed, 44 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index 5db6e789e6b8..7b880cb7e022 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -27,6 +27,40 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ pmic-glink {
+ compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -546,7 +580,16 @@ &usb_1 {
};
&usb_1_dwc3 {
- dr_mode = "peripheral";
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_1_hsphy {
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 10/11] arm64: dts: qcom: sm8550-mtp: add pmic glink node
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++++++++++++++++++++++++++++++++-
1 file changed, 44 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index 5db6e789e6b8..7b880cb7e022 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -27,6 +27,40 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ pmic-glink {
+ compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+ };
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -546,7 +580,16 @@ &usb_1 {
};
&usb_1_dwc3 {
- dr_mode = "peripheral";
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&pmic_glink_ss_in>;
};
&usb_1_hsphy {
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 11/11] arm64: defconfig: add PMIC GLINK modules
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:02 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Enable the PMIC GLINK core, altmode, battery and UCSI
aux drivers as module to enable USB Type-C management
over the PMIC GLINK protocol on modern Qcom platforms.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/configs/defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index e7e42bf79a26..1773254de7fb 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -287,6 +287,10 @@ CONFIG_VIRTIO_BLK=y
CONFIG_BLK_DEV_NVME=m
CONFIG_QCOM_COINCELL=m
CONFIG_QCOM_FASTRPC=m
+CONFIG_BATTERY_QCOM_BATTMGR=m
+CONFIG_QCOM_PMIC_GLINK=m
+CONFIG_TYPEC_UCSI=m
+CONFIG_UCSI_PMIC_GLINK=m
CONFIG_SRAM=y
CONFIG_PCI_ENDPOINT_TEST=m
CONFIG_EEPROM_AT24=m
--
2.34.1
^ permalink raw reply related [flat|nested] 52+ messages in thread
* [PATCH v2 11/11] arm64: defconfig: add PMIC GLINK modules
@ 2023-02-10 15:02 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:02 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Bjorn Andersson,
Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Catalin Marinas,
Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel, Neil Armstrong
Enable the PMIC GLINK core, altmode, battery and UCSI
aux drivers as module to enable USB Type-C management
over the PMIC GLINK protocol on modern Qcom platforms.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/configs/defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index e7e42bf79a26..1773254de7fb 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -287,6 +287,10 @@ CONFIG_VIRTIO_BLK=y
CONFIG_BLK_DEV_NVME=m
CONFIG_QCOM_COINCELL=m
CONFIG_QCOM_FASTRPC=m
+CONFIG_BATTERY_QCOM_BATTMGR=m
+CONFIG_QCOM_PMIC_GLINK=m
+CONFIG_TYPEC_UCSI=m
+CONFIG_UCSI_PMIC_GLINK=m
CONFIG_SRAM=y
CONFIG_PCI_ENDPOINT_TEST=m
CONFIG_EEPROM_AT24=m
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 52+ messages in thread
* Re: [PATCH v2 05/11] arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:19 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:19 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add ports subnodes in dwc3 node to avoid repeating the
> same description in each board DT.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> index 0a422637b61f..3f4631e06187 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> @@ -2727,6 +2727,25 @@ usb_1_dwc3: usb@a600000 {
> snps,dis_enblslpm_quirk;
> phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
> phy-names = "usb2-phy", "usb3-phy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + };
> + };
> + };
> };
> };
>
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 05/11] arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
@ 2023-02-10 15:19 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:19 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add ports subnodes in dwc3 node to avoid repeating the
> same description in each board DT.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> index 0a422637b61f..3f4631e06187 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> @@ -2727,6 +2727,25 @@ usb_1_dwc3: usb@a600000 {
> snps,dis_enblslpm_quirk;
> phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
> phy-names = "usb2-phy", "usb3-phy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + };
> + };
> + };
> };
> };
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 06/11] arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:19 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:19 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add ports subnodes in dwc3 node to avoid repeating the
> same description in each board DT.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 1a744a33bcf4..ccda73426ee2 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -4155,6 +4155,25 @@ usb_1_dwc3: usb@a600000 {
> snps,dis_enblslpm_quirk;
> phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
> phy-names = "usb2-phy", "usb3-phy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + };
> + };
> + };
> };
> };
>
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 06/11] arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
@ 2023-02-10 15:19 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:19 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add ports subnodes in dwc3 node to avoid repeating the
> same description in each board DT.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> index 1a744a33bcf4..ccda73426ee2 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
> @@ -4155,6 +4155,25 @@ usb_1_dwc3: usb@a600000 {
> snps,dis_enblslpm_quirk;
> phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
> phy-names = "usb2-phy", "usb3-phy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + };
> + };
> + };
> };
> };
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 07/11] arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:19 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:19 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add ports subnodes in dwc3 node to avoid repeating the
> same description in each board DT.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> index 9910006c32aa..2914a12a1c89 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -2469,6 +2469,25 @@ usb_1_dwc3: usb@a600000 {
> phys = <&usb_1_hsphy>,
> <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
> phy-names = "usb2-phy", "usb3-phy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + };
> + };
> + };
> };
> };
>
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 07/11] arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
@ 2023-02-10 15:19 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:19 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add ports subnodes in dwc3 node to avoid repeating the
> same description in each board DT.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> index 9910006c32aa..2914a12a1c89 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -2469,6 +2469,25 @@ usb_1_dwc3: usb@a600000 {
> phys = <&usb_1_hsphy>,
> <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
> phy-names = "usb2-phy", "usb3-phy";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + };
> + };
> + };
> };
> };
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:21 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:21 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 54654eb75c28..28fc9a835c5d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
> };
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -666,23 +700,42 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - /* TODO: Define USB-C connector properly */
> - dr_mode = "peripheral";
> -};
> + dr_mode = "otg";
> + usb-role-switch;
>
> -&usb_1_hsphy {
Are you removing the hsphy completely?
Konrad
> - status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - vdda-pll-supply = <&vreg_l5b_0p88>;
> - vdda18-supply = <&vreg_l1c_1p8>;
> - vdda33-supply = <&vreg_l2b_3p07>;
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + remote-endpoint = <&pmic_glink_hs_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
> + };
> + };
> + };
> };
>
> -&usb_1_qmpphy {
> - status = "okay";
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> +};
>
> - vdda-phy-supply = <&vreg_l6b_1p2>;
> - vdda-pll-supply = <&vreg_l1b_0p88>;
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_2 {
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
@ 2023-02-10 15:21 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:21 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 54654eb75c28..28fc9a835c5d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
> };
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -666,23 +700,42 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - /* TODO: Define USB-C connector properly */
> - dr_mode = "peripheral";
> -};
> + dr_mode = "otg";
> + usb-role-switch;
>
> -&usb_1_hsphy {
Are you removing the hsphy completely?
Konrad
> - status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - vdda-pll-supply = <&vreg_l5b_0p88>;
> - vdda18-supply = <&vreg_l1c_1p8>;
> - vdda33-supply = <&vreg_l2b_3p07>;
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + remote-endpoint = <&pmic_glink_hs_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
> + };
> + };
> + };
> };
>
> -&usb_1_qmpphy {
> - status = "okay";
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> +};
>
> - vdda-phy-supply = <&vreg_l6b_1p2>;
> - vdda-pll-supply = <&vreg_l1b_0p88>;
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_2 {
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 09/11] arm64: dts: qcom: sm8450-hdk: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:22 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:22 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++++++++++++++++++++++++++++++++-
> 1 file changed, 44 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index feef3837e4cd..1755ee3aa04c 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -87,6 +87,40 @@ lt9611_3v3: lt9611-3v3-regulator {
> enable-active-high;
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -724,7 +758,16 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - dr_mode = "peripheral";
> + dr_mode = "otg";
> + usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_1_hsphy {
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 09/11] arm64: dts: qcom: sm8450-hdk: add pmic glink node
@ 2023-02-10 15:22 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:22 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++++++++++++++++++++++++++++++++-
> 1 file changed, 44 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> index feef3837e4cd..1755ee3aa04c 100644
> --- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
> @@ -87,6 +87,40 @@ lt9611_3v3: lt9611-3v3-regulator {
> enable-active-high;
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -724,7 +758,16 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - dr_mode = "peripheral";
> + dr_mode = "otg";
> + usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_1_hsphy {
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 10/11] arm64: dts: qcom: sm8550-mtp: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:22 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:22 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++++++++++++++++++++++++++++++++-
> 1 file changed, 44 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
> index 5db6e789e6b8..7b880cb7e022 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
> @@ -27,6 +27,40 @@ chosen {
> stdout-path = "serial0:115200n8";
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -546,7 +580,16 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - dr_mode = "peripheral";
> + dr_mode = "otg";
> + usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_1_hsphy {
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 10/11] arm64: dts: qcom: sm8550-mtp: add pmic glink node
@ 2023-02-10 15:22 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:22 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++++++++++++++++++++++++++++++++-
> 1 file changed, 44 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
> index 5db6e789e6b8..7b880cb7e022 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
> @@ -27,6 +27,40 @@ chosen {
> stdout-path = "serial0:115200n8";
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -546,7 +580,16 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - dr_mode = "peripheral";
> + dr_mode = "otg";
> + usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_1_hsphy {
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 11/11] arm64: defconfig: add PMIC GLINK modules
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:22 ` Konrad Dybcio
-1 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:22 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Enable the PMIC GLINK core, altmode, battery and UCSI
> aux drivers as module to enable USB Type-C management
> over the PMIC GLINK protocol on modern Qcom platforms.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/configs/defconfig | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index e7e42bf79a26..1773254de7fb 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -287,6 +287,10 @@ CONFIG_VIRTIO_BLK=y
> CONFIG_BLK_DEV_NVME=m
> CONFIG_QCOM_COINCELL=m
> CONFIG_QCOM_FASTRPC=m
> +CONFIG_BATTERY_QCOM_BATTMGR=m
> +CONFIG_QCOM_PMIC_GLINK=m
> +CONFIG_TYPEC_UCSI=m
> +CONFIG_UCSI_PMIC_GLINK=m
> CONFIG_SRAM=y
> CONFIG_PCI_ENDPOINT_TEST=m
> CONFIG_EEPROM_AT24=m
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 11/11] arm64: defconfig: add PMIC GLINK modules
@ 2023-02-10 15:22 ` Konrad Dybcio
0 siblings, 0 replies; 52+ messages in thread
From: Konrad Dybcio @ 2023-02-10 15:22 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10.02.2023 16:02, Neil Armstrong wrote:
> Enable the PMIC GLINK core, altmode, battery and UCSI
> aux drivers as module to enable USB Type-C management
> over the PMIC GLINK protocol on modern Qcom platforms.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/configs/defconfig | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index e7e42bf79a26..1773254de7fb 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -287,6 +287,10 @@ CONFIG_VIRTIO_BLK=y
> CONFIG_BLK_DEV_NVME=m
> CONFIG_QCOM_COINCELL=m
> CONFIG_QCOM_FASTRPC=m
> +CONFIG_BATTERY_QCOM_BATTMGR=m
> +CONFIG_QCOM_PMIC_GLINK=m
> +CONFIG_TYPEC_UCSI=m
> +CONFIG_UCSI_PMIC_GLINK=m
> CONFIG_SRAM=y
> CONFIG_PCI_ENDPOINT_TEST=m
> CONFIG_EEPROM_AT24=m
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
2023-02-10 15:21 ` Konrad Dybcio
@ 2023-02-10 15:26 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:26 UTC (permalink / raw)
To: Konrad Dybcio, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10/02/2023 16:21, Konrad Dybcio wrote:
>
>
> On 10.02.2023 16:02, Neil Armstrong wrote:
>> Add the pmic glink node linked with the DWC3 USB controller
>> switched to OTG mode and tagged with usb-role-switch.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
>> 1 file changed, 65 insertions(+), 12 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> index 54654eb75c28..28fc9a835c5d 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
>> };
>> };
>>
>> + pmic-glink {
>> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + connector@0 {
>> + compatible = "usb-c-connector";
>> + reg = <0>;
>> + power-role = "dual";
>> + data-role = "dual";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + pmic_glink_hs_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_hs>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + pmic_glink_ss_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_ss>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +
>> vph_pwr: vph-pwr-regulator {
>> compatible = "regulator-fixed";
>> regulator-name = "vph_pwr";
>> @@ -666,23 +700,42 @@ &usb_1 {
>> };
>>
>> &usb_1_dwc3 {
>> - /* TODO: Define USB-C connector properly */
>> - dr_mode = "peripheral";
>> -};
>> + dr_mode = "otg";
>> + usb-role-switch;
>>
>> -&usb_1_hsphy {
> Are you removing the hsphy completely?
Oops seems I did remove too much stuff... thx for noticing
>
> Konrad
>> - status = "okay";
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>>
>> - vdda-pll-supply = <&vreg_l5b_0p88>;
>> - vdda18-supply = <&vreg_l1c_1p8>;
>> - vdda33-supply = <&vreg_l2b_3p07>;
>> + port@0 {
>> + reg = <0>;
>> +
>> + usb_1_dwc3_hs: endpoint {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + usb_1_dwc3_ss: endpoint {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>> + };
>> + };
>> + };
>> };
>>
>> -&usb_1_qmpphy {
>> - status = "okay";
>> +&usb_1_dwc3 {
>> + dr_mode = "otg";
>> + usb-role-switch;
>> +};
>>
>> - vdda-phy-supply = <&vreg_l6b_1p2>;
>> - vdda-pll-supply = <&vreg_l1b_0p88>;
>> +&usb_1_dwc3_hs {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> +};
>> +
>> +&usb_1_dwc3_ss {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>> };
>>
>> &usb_2 {
>>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
@ 2023-02-10 15:26 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-10 15:26 UTC (permalink / raw)
To: Konrad Dybcio, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10/02/2023 16:21, Konrad Dybcio wrote:
>
>
> On 10.02.2023 16:02, Neil Armstrong wrote:
>> Add the pmic glink node linked with the DWC3 USB controller
>> switched to OTG mode and tagged with usb-role-switch.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
>> 1 file changed, 65 insertions(+), 12 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> index 54654eb75c28..28fc9a835c5d 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
>> };
>> };
>>
>> + pmic-glink {
>> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + connector@0 {
>> + compatible = "usb-c-connector";
>> + reg = <0>;
>> + power-role = "dual";
>> + data-role = "dual";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + pmic_glink_hs_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_hs>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + pmic_glink_ss_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_ss>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +
>> vph_pwr: vph-pwr-regulator {
>> compatible = "regulator-fixed";
>> regulator-name = "vph_pwr";
>> @@ -666,23 +700,42 @@ &usb_1 {
>> };
>>
>> &usb_1_dwc3 {
>> - /* TODO: Define USB-C connector properly */
>> - dr_mode = "peripheral";
>> -};
>> + dr_mode = "otg";
>> + usb-role-switch;
>>
>> -&usb_1_hsphy {
> Are you removing the hsphy completely?
Oops seems I did remove too much stuff... thx for noticing
>
> Konrad
>> - status = "okay";
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>>
>> - vdda-pll-supply = <&vreg_l5b_0p88>;
>> - vdda18-supply = <&vreg_l1c_1p8>;
>> - vdda33-supply = <&vreg_l2b_3p07>;
>> + port@0 {
>> + reg = <0>;
>> +
>> + usb_1_dwc3_hs: endpoint {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + usb_1_dwc3_ss: endpoint {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>> + };
>> + };
>> + };
>> };
>>
>> -&usb_1_qmpphy {
>> - status = "okay";
>> +&usb_1_dwc3 {
>> + dr_mode = "otg";
>> + usb-role-switch;
>> +};
>>
>> - vdda-phy-supply = <&vreg_l6b_1p2>;
>> - vdda-pll-supply = <&vreg_l1b_0p88>;
>> +&usb_1_dwc3_hs {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> +};
>> +
>> +&usb_1_dwc3_ss {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>> };
>>
>> &usb_2 {
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:41 ` Dmitry Baryshkov
-1 siblings, 0 replies; 52+ messages in thread
From: Dmitry Baryshkov @ 2023-02-10 15:41 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10/02/2023 17:02, Neil Armstrong wrote:
> Only register UCSI on know working devices, like on the SM8450
> or Sm8550 which requires UCSI to get USB mode switch events.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> drivers/soc/qcom/pmic_glink.c | 67 ++++++++++++++++++++++++++++++++++++-------
> 1 file changed, 57 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> index bb3fb57abcc6..c7f091f4a8c1 100644
> --- a/drivers/soc/qcom/pmic_glink.c
> +++ b/drivers/soc/qcom/pmic_glink.c
> @@ -4,6 +4,7 @@
> * Copyright (c) 2022, Linaro Ltd
> */
> #include <linux/auxiliary_bus.h>
> +#include <linux/of_device.h>
> #include <linux/module.h>
> #include <linux/platform_device.h>
> #include <linux/rpmsg.h>
> @@ -11,12 +12,23 @@
> #include <linux/soc/qcom/pdr.h>
> #include <linux/soc/qcom/pmic_glink.h>
>
> +enum {
> + PMIC_GLINK_CLIENT_BATT = 0,
> + PMIC_GLINK_CLIENT_ALTMODE,
> + PMIC_GLINK_CLIENT_UCSI,
> +};
> +
> +#define PMIC_GLINK_CLIENT_DEFAULT (BIT(PMIC_GLINK_CLIENT_BATT) | \
> + BIT(PMIC_GLINK_CLIENT_ALTMODE))
> +
> struct pmic_glink {
> struct device *dev;
> struct pdr_handle *pdr;
>
> struct rpmsg_endpoint *ept;
>
> + unsigned int client_mask;
> +
> struct auxiliary_device altmode_aux;
> struct auxiliary_device ps_aux;
> struct auxiliary_device ucsi_aux;
> @@ -231,8 +243,19 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
> },
> };
>
> +/* Do not handle altmode for now on those platforms */
> +static const unsigned int pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
> + BIT(PMIC_GLINK_CLIENT_UCSI);
> +
> +static const struct of_device_id pmic_glink_of_client_mask[] = {
> + { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + {}
> +};
> +
Squash this into pmic_glink_of_match, please. Then you can use
of_device_get_match_data()
> static int pmic_glink_probe(struct platform_device *pdev)
> {
> + const struct of_device_id *match;
> struct pdr_service *service;
> struct pmic_glink *pg;
> int ret;
> @@ -249,12 +272,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
> mutex_init(&pg->client_lock);
> mutex_init(&pg->state_lock);
>
> - ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> - if (ret)
> - return ret;
> - ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> - if (ret)
> - goto out_release_altmode_aux;
> + match = of_match_device(pmic_glink_of_client_mask, &pdev->dev);
> + if (match)
> + pg->client_mask = *(const unsigned int *)match->data;
> + else
> + pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
> +
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
> + if (ret)
> + return ret;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> + if (ret)
> + goto out_release_ucsi_aux;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> + if (ret)
> + goto out_release_altmode_aux;
> + }
>
> pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
> if (IS_ERR(pg->pdr)) {
> @@ -278,9 +316,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
> out_release_pdr_handle:
> pdr_handle_release(pg->pdr);
> out_release_aux_devices:
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> out_release_altmode_aux:
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> +out_release_ucsi_aux:
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> return ret;
> }
> @@ -291,8 +334,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
>
> pdr_handle_release(pg->pdr);
>
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> mutex_lock(&__pmic_glink_lock);
> __pmic_glink = NULL;
>
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device
@ 2023-02-10 15:41 ` Dmitry Baryshkov
0 siblings, 0 replies; 52+ messages in thread
From: Dmitry Baryshkov @ 2023-02-10 15:41 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10/02/2023 17:02, Neil Armstrong wrote:
> Only register UCSI on know working devices, like on the SM8450
> or Sm8550 which requires UCSI to get USB mode switch events.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> drivers/soc/qcom/pmic_glink.c | 67 ++++++++++++++++++++++++++++++++++++-------
> 1 file changed, 57 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> index bb3fb57abcc6..c7f091f4a8c1 100644
> --- a/drivers/soc/qcom/pmic_glink.c
> +++ b/drivers/soc/qcom/pmic_glink.c
> @@ -4,6 +4,7 @@
> * Copyright (c) 2022, Linaro Ltd
> */
> #include <linux/auxiliary_bus.h>
> +#include <linux/of_device.h>
> #include <linux/module.h>
> #include <linux/platform_device.h>
> #include <linux/rpmsg.h>
> @@ -11,12 +12,23 @@
> #include <linux/soc/qcom/pdr.h>
> #include <linux/soc/qcom/pmic_glink.h>
>
> +enum {
> + PMIC_GLINK_CLIENT_BATT = 0,
> + PMIC_GLINK_CLIENT_ALTMODE,
> + PMIC_GLINK_CLIENT_UCSI,
> +};
> +
> +#define PMIC_GLINK_CLIENT_DEFAULT (BIT(PMIC_GLINK_CLIENT_BATT) | \
> + BIT(PMIC_GLINK_CLIENT_ALTMODE))
> +
> struct pmic_glink {
> struct device *dev;
> struct pdr_handle *pdr;
>
> struct rpmsg_endpoint *ept;
>
> + unsigned int client_mask;
> +
> struct auxiliary_device altmode_aux;
> struct auxiliary_device ps_aux;
> struct auxiliary_device ucsi_aux;
> @@ -231,8 +243,19 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
> },
> };
>
> +/* Do not handle altmode for now on those platforms */
> +static const unsigned int pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
> + BIT(PMIC_GLINK_CLIENT_UCSI);
> +
> +static const struct of_device_id pmic_glink_of_client_mask[] = {
> + { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + {}
> +};
> +
Squash this into pmic_glink_of_match, please. Then you can use
of_device_get_match_data()
> static int pmic_glink_probe(struct platform_device *pdev)
> {
> + const struct of_device_id *match;
> struct pdr_service *service;
> struct pmic_glink *pg;
> int ret;
> @@ -249,12 +272,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
> mutex_init(&pg->client_lock);
> mutex_init(&pg->state_lock);
>
> - ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> - if (ret)
> - return ret;
> - ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> - if (ret)
> - goto out_release_altmode_aux;
> + match = of_match_device(pmic_glink_of_client_mask, &pdev->dev);
> + if (match)
> + pg->client_mask = *(const unsigned int *)match->data;
> + else
> + pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
> +
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
> + if (ret)
> + return ret;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> + if (ret)
> + goto out_release_ucsi_aux;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> + if (ret)
> + goto out_release_altmode_aux;
> + }
>
> pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
> if (IS_ERR(pg->pdr)) {
> @@ -278,9 +316,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
> out_release_pdr_handle:
> pdr_handle_release(pg->pdr);
> out_release_aux_devices:
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> out_release_altmode_aux:
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> +out_release_ucsi_aux:
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> return ret;
> }
> @@ -291,8 +334,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
>
> pdr_handle_release(pg->pdr);
>
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> mutex_lock(&__pmic_glink_lock);
> __pmic_glink = NULL;
>
--
With best wishes
Dmitry
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 15:44 ` Dmitry Baryshkov
-1 siblings, 0 replies; 52+ messages in thread
From: Dmitry Baryshkov @ 2023-02-10 15:44 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10/02/2023 17:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 54654eb75c28..28fc9a835c5d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
> };
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -666,23 +700,42 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - /* TODO: Define USB-C connector properly */
> - dr_mode = "peripheral";
> -};
> + dr_mode = "otg";
I could not verify UCSI / OTG on sm8350-HDK, see the GET_PDOS issue.
Unless it is fixed, I suggest fixing this to "host" to get DP to work.
> + usb-role-switch;
>
> -&usb_1_hsphy {
> - status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - vdda-pll-supply = <&vreg_l5b_0p88>;
> - vdda18-supply = <&vreg_l1c_1p8>;
> - vdda33-supply = <&vreg_l2b_3p07>;
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + remote-endpoint = <&pmic_glink_hs_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
> + };
> + };
> + };
> };
>
> -&usb_1_qmpphy {
> - status = "okay";
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> +};
Duplicate
>
> - vdda-phy-supply = <&vreg_l6b_1p2>;
> - vdda-pll-supply = <&vreg_l1b_0p88>;
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_2 {
>
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
@ 2023-02-10 15:44 ` Dmitry Baryshkov
0 siblings, 0 replies; 52+ messages in thread
From: Dmitry Baryshkov @ 2023-02-10 15:44 UTC (permalink / raw)
To: Neil Armstrong, Heikki Krogerus, Greg Kroah-Hartman, Andy Gross,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Catalin Marinas, Will Deacon
Cc: linux-kernel, linux-usb, linux-arm-msm, devicetree, linux-arm-kernel
On 10/02/2023 17:02, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 54654eb75c28..28fc9a835c5d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
> };
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -666,23 +700,42 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - /* TODO: Define USB-C connector properly */
> - dr_mode = "peripheral";
> -};
> + dr_mode = "otg";
I could not verify UCSI / OTG on sm8350-HDK, see the GET_PDOS issue.
Unless it is fixed, I suggest fixing this to "host" to get DP to work.
> + usb-role-switch;
>
> -&usb_1_hsphy {
> - status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - vdda-pll-supply = <&vreg_l5b_0p88>;
> - vdda18-supply = <&vreg_l1c_1p8>;
> - vdda33-supply = <&vreg_l2b_3p07>;
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + remote-endpoint = <&pmic_glink_hs_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
> + };
> + };
> + };
> };
>
> -&usb_1_qmpphy {
> - status = "okay";
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> +};
Duplicate
>
> - vdda-phy-supply = <&vreg_l6b_1p2>;
> - vdda-pll-supply = <&vreg_l1b_0p88>;
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_2 {
>
--
With best wishes
Dmitry
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 20:10 ` Bjorn Andersson
-1 siblings, 0 replies; 52+ messages in thread
From: Bjorn Andersson @ 2023-02-10 20:10 UTC (permalink / raw)
To: Neil Armstrong
Cc: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
On Fri, Feb 10, 2023 at 04:02:07PM +0100, Neil Armstrong wrote:
> Only register UCSI on know working devices, like on the SM8450
> or Sm8550 which requires UCSI to get USB mode switch events.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> drivers/soc/qcom/pmic_glink.c | 67 ++++++++++++++++++++++++++++++++++++-------
> 1 file changed, 57 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> index bb3fb57abcc6..c7f091f4a8c1 100644
> --- a/drivers/soc/qcom/pmic_glink.c
> +++ b/drivers/soc/qcom/pmic_glink.c
> @@ -4,6 +4,7 @@
> * Copyright (c) 2022, Linaro Ltd
> */
> #include <linux/auxiliary_bus.h>
> +#include <linux/of_device.h>
> #include <linux/module.h>
> #include <linux/platform_device.h>
> #include <linux/rpmsg.h>
> @@ -11,12 +12,23 @@
> #include <linux/soc/qcom/pdr.h>
> #include <linux/soc/qcom/pmic_glink.h>
>
> +enum {
> + PMIC_GLINK_CLIENT_BATT = 0,
> + PMIC_GLINK_CLIENT_ALTMODE,
> + PMIC_GLINK_CLIENT_UCSI,
> +};
> +
> +#define PMIC_GLINK_CLIENT_DEFAULT (BIT(PMIC_GLINK_CLIENT_BATT) | \
> + BIT(PMIC_GLINK_CLIENT_ALTMODE))
> +
> struct pmic_glink {
> struct device *dev;
> struct pdr_handle *pdr;
>
> struct rpmsg_endpoint *ept;
>
> + unsigned int client_mask;
> +
> struct auxiliary_device altmode_aux;
> struct auxiliary_device ps_aux;
> struct auxiliary_device ucsi_aux;
> @@ -231,8 +243,19 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
> },
> };
>
> +/* Do not handle altmode for now on those platforms */
> +static const unsigned int pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
> + BIT(PMIC_GLINK_CLIENT_UCSI);
> +
> +static const struct of_device_id pmic_glink_of_client_mask[] = {
> + { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + {}
> +};
> +
> static int pmic_glink_probe(struct platform_device *pdev)
> {
> + const struct of_device_id *match;
> struct pdr_service *service;
> struct pmic_glink *pg;
> int ret;
> @@ -249,12 +272,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
> mutex_init(&pg->client_lock);
> mutex_init(&pg->state_lock);
>
> - ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> - if (ret)
> - return ret;
> - ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> - if (ret)
> - goto out_release_altmode_aux;
> + match = of_match_device(pmic_glink_of_client_mask, &pdev->dev);
> + if (match)
> + pg->client_mask = *(const unsigned int *)match->data;
Make pmic_glink_sm8450_client_mask unsigned long instead, then it will
have the same size as void * and you don't need to dereference it
here...
> + else
> + pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
Let's move these bits to pmic_glink_of_match[] to avoid having two
different of_device_id to keep in sync.
And hopefully we could have "qcom,pmic_glink" represent the case of
having all 3 bits set soon, and special case what you have as
"default" here...
Regards,
Bjorn
> +
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
> + if (ret)
> + return ret;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> + if (ret)
> + goto out_release_ucsi_aux;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> + if (ret)
> + goto out_release_altmode_aux;
> + }
>
> pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
> if (IS_ERR(pg->pdr)) {
> @@ -278,9 +316,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
> out_release_pdr_handle:
> pdr_handle_release(pg->pdr);
> out_release_aux_devices:
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> out_release_altmode_aux:
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> +out_release_ucsi_aux:
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> return ret;
> }
> @@ -291,8 +334,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
>
> pdr_handle_release(pg->pdr);
>
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> mutex_lock(&__pmic_glink_lock);
> __pmic_glink = NULL;
>
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device
@ 2023-02-10 20:10 ` Bjorn Andersson
0 siblings, 0 replies; 52+ messages in thread
From: Bjorn Andersson @ 2023-02-10 20:10 UTC (permalink / raw)
To: Neil Armstrong
Cc: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
On Fri, Feb 10, 2023 at 04:02:07PM +0100, Neil Armstrong wrote:
> Only register UCSI on know working devices, like on the SM8450
> or Sm8550 which requires UCSI to get USB mode switch events.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> drivers/soc/qcom/pmic_glink.c | 67 ++++++++++++++++++++++++++++++++++++-------
> 1 file changed, 57 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> index bb3fb57abcc6..c7f091f4a8c1 100644
> --- a/drivers/soc/qcom/pmic_glink.c
> +++ b/drivers/soc/qcom/pmic_glink.c
> @@ -4,6 +4,7 @@
> * Copyright (c) 2022, Linaro Ltd
> */
> #include <linux/auxiliary_bus.h>
> +#include <linux/of_device.h>
> #include <linux/module.h>
> #include <linux/platform_device.h>
> #include <linux/rpmsg.h>
> @@ -11,12 +12,23 @@
> #include <linux/soc/qcom/pdr.h>
> #include <linux/soc/qcom/pmic_glink.h>
>
> +enum {
> + PMIC_GLINK_CLIENT_BATT = 0,
> + PMIC_GLINK_CLIENT_ALTMODE,
> + PMIC_GLINK_CLIENT_UCSI,
> +};
> +
> +#define PMIC_GLINK_CLIENT_DEFAULT (BIT(PMIC_GLINK_CLIENT_BATT) | \
> + BIT(PMIC_GLINK_CLIENT_ALTMODE))
> +
> struct pmic_glink {
> struct device *dev;
> struct pdr_handle *pdr;
>
> struct rpmsg_endpoint *ept;
>
> + unsigned int client_mask;
> +
> struct auxiliary_device altmode_aux;
> struct auxiliary_device ps_aux;
> struct auxiliary_device ucsi_aux;
> @@ -231,8 +243,19 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
> },
> };
>
> +/* Do not handle altmode for now on those platforms */
> +static const unsigned int pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
> + BIT(PMIC_GLINK_CLIENT_UCSI);
> +
> +static const struct of_device_id pmic_glink_of_client_mask[] = {
> + { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> + {}
> +};
> +
> static int pmic_glink_probe(struct platform_device *pdev)
> {
> + const struct of_device_id *match;
> struct pdr_service *service;
> struct pmic_glink *pg;
> int ret;
> @@ -249,12 +272,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
> mutex_init(&pg->client_lock);
> mutex_init(&pg->state_lock);
>
> - ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> - if (ret)
> - return ret;
> - ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> - if (ret)
> - goto out_release_altmode_aux;
> + match = of_match_device(pmic_glink_of_client_mask, &pdev->dev);
> + if (match)
> + pg->client_mask = *(const unsigned int *)match->data;
Make pmic_glink_sm8450_client_mask unsigned long instead, then it will
have the same size as void * and you don't need to dereference it
here...
> + else
> + pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
Let's move these bits to pmic_glink_of_match[] to avoid having two
different of_device_id to keep in sync.
And hopefully we could have "qcom,pmic_glink" represent the case of
having all 3 bits set soon, and special case what you have as
"default" here...
Regards,
Bjorn
> +
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
> + if (ret)
> + return ret;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
> + if (ret)
> + goto out_release_ucsi_aux;
> + }
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
> + ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
> + if (ret)
> + goto out_release_altmode_aux;
> + }
>
> pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
> if (IS_ERR(pg->pdr)) {
> @@ -278,9 +316,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
> out_release_pdr_handle:
> pdr_handle_release(pg->pdr);
> out_release_aux_devices:
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> out_release_altmode_aux:
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> +out_release_ucsi_aux:
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> return ret;
> }
> @@ -291,8 +334,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
>
> pdr_handle_release(pg->pdr);
>
> - pmic_glink_del_aux_device(pg, &pg->ps_aux);
> - pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
> + pmic_glink_del_aux_device(pg, &pg->ps_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
> + pmic_glink_del_aux_device(pg, &pg->altmode_aux);
> + if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
> + pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
>
> mutex_lock(&__pmic_glink_lock);
> __pmic_glink = NULL;
>
> --
> 2.34.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-10 20:13 ` Bjorn Andersson
-1 siblings, 0 replies; 52+ messages in thread
From: Bjorn Andersson @ 2023-02-10 20:13 UTC (permalink / raw)
To: Neil Armstrong
Cc: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
On Fri, Feb 10, 2023 at 04:02:11PM +0100, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 54654eb75c28..28fc9a835c5d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
> };
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -666,23 +700,42 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - /* TODO: Define USB-C connector properly */
> - dr_mode = "peripheral";
> -};
> + dr_mode = "otg";
> + usb-role-switch;
>
> -&usb_1_hsphy {
> - status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - vdda-pll-supply = <&vreg_l5b_0p88>;
> - vdda18-supply = <&vreg_l1c_1p8>;
> - vdda33-supply = <&vreg_l2b_3p07>;
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + remote-endpoint = <&pmic_glink_hs_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
The connector is indeed the next active component on the SuperSpeed
lanes for USB. But as you're targeting to introduce QMP on that path,
connector@0/port@1 would be pointing to QMP/ports/port@N.
Do you plan to express the datapath between USB and QMP using this port
at that time? (It's the correct thing to do...)
Or will we not describe the SS lanes in this scenario?
Regards,
Bjorn
> + };
> + };
> + };
> };
>
> -&usb_1_qmpphy {
> - status = "okay";
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> +};
>
> - vdda-phy-supply = <&vreg_l6b_1p2>;
> - vdda-pll-supply = <&vreg_l1b_0p88>;
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_2 {
>
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
@ 2023-02-10 20:13 ` Bjorn Andersson
0 siblings, 0 replies; 52+ messages in thread
From: Bjorn Andersson @ 2023-02-10 20:13 UTC (permalink / raw)
To: Neil Armstrong
Cc: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
On Fri, Feb 10, 2023 at 04:02:11PM +0100, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
> 1 file changed, 65 insertions(+), 12 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> index 54654eb75c28..28fc9a835c5d 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
> };
> };
>
> + pmic-glink {
> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_ss>;
> + };
> + };
> + };
> + };
> + };
> +
> vph_pwr: vph-pwr-regulator {
> compatible = "regulator-fixed";
> regulator-name = "vph_pwr";
> @@ -666,23 +700,42 @@ &usb_1 {
> };
>
> &usb_1_dwc3 {
> - /* TODO: Define USB-C connector properly */
> - dr_mode = "peripheral";
> -};
> + dr_mode = "otg";
> + usb-role-switch;
>
> -&usb_1_hsphy {
> - status = "okay";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
>
> - vdda-pll-supply = <&vreg_l5b_0p88>;
> - vdda18-supply = <&vreg_l1c_1p8>;
> - vdda33-supply = <&vreg_l2b_3p07>;
> + port@0 {
> + reg = <0>;
> +
> + usb_1_dwc3_hs: endpoint {
> + remote-endpoint = <&pmic_glink_hs_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + usb_1_dwc3_ss: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
The connector is indeed the next active component on the SuperSpeed
lanes for USB. But as you're targeting to introduce QMP on that path,
connector@0/port@1 would be pointing to QMP/ports/port@N.
Do you plan to express the datapath between USB and QMP using this port
at that time? (It's the correct thing to do...)
Or will we not describe the SS lanes in this scenario?
Regards,
Bjorn
> + };
> + };
> + };
> };
>
> -&usb_1_qmpphy {
> - status = "okay";
> +&usb_1_dwc3 {
> + dr_mode = "otg";
> + usb-role-switch;
> +};
>
> - vdda-phy-supply = <&vreg_l6b_1p2>;
> - vdda-pll-supply = <&vreg_l1b_0p88>;
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> + remote-endpoint = <&pmic_glink_ss_in>;
> };
>
> &usb_2 {
>
> --
> 2.34.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
2023-02-10 20:13 ` Bjorn Andersson
@ 2023-02-13 12:41 ` Neil Armstrong
-1 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-13 12:41 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
On 10/02/2023 21:13, Bjorn Andersson wrote:
> On Fri, Feb 10, 2023 at 04:02:11PM +0100, Neil Armstrong wrote:
>> Add the pmic glink node linked with the DWC3 USB controller
>> switched to OTG mode and tagged with usb-role-switch.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
>> 1 file changed, 65 insertions(+), 12 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> index 54654eb75c28..28fc9a835c5d 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
>> };
>> };
>>
>> + pmic-glink {
>> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + connector@0 {
>> + compatible = "usb-c-connector";
>> + reg = <0>;
>> + power-role = "dual";
>> + data-role = "dual";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + pmic_glink_hs_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_hs>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + pmic_glink_ss_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_ss>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +
>> vph_pwr: vph-pwr-regulator {
>> compatible = "regulator-fixed";
>> regulator-name = "vph_pwr";
>> @@ -666,23 +700,42 @@ &usb_1 {
>> };
>>
>> &usb_1_dwc3 {
>> - /* TODO: Define USB-C connector properly */
>> - dr_mode = "peripheral";
>> -};
>> + dr_mode = "otg";
>> + usb-role-switch;
>>
>> -&usb_1_hsphy {
>> - status = "okay";
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>>
>> - vdda-pll-supply = <&vreg_l5b_0p88>;
>> - vdda18-supply = <&vreg_l1c_1p8>;
>> - vdda33-supply = <&vreg_l2b_3p07>;
>> + port@0 {
>> + reg = <0>;
>> +
>> + usb_1_dwc3_hs: endpoint {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + usb_1_dwc3_ss: endpoint {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>
> The connector is indeed the next active component on the SuperSpeed
> lanes for USB. But as you're targeting to introduce QMP on that path,
> connector@0/port@1 would be pointing to QMP/ports/port@N.
>
> Do you plan to express the datapath between USB and QMP using this port
> at that time? (It's the correct thing to do...)
Yeah we need to figure out, because ultimately the datapath should be:
connector:
port0 --> usb_1_dwc3_hs
port1 --> qmpphy --> usb_1_dwc3_ss
port2 --> fsa4480 --> qmpphy -> dp_controller
And with a retimer, it gets even more complex:
connector:
port0 --> usb_1_dwc3_hs
port1 --> retimer --> qmpphy --> usb_1_dwc3_ss
port2 --> retimer --> qmpphy -> dp_controller
The solution I was using is instead of having chained port/endpoints,
I use multiple endpoints like :
port0 --> usb_1_dwc3_hs
port1 --> ep0: usb_1_dwc3_ss
ep1: qmpphy
port2 --> ep0: fsa4480
ep1: dp_controller
But I'm sure this is valid... but it is much simpler.
Neil
>
> Or will we not describe the SS lanes in this scenario?
>
> Regards,
> Bjorn
>
>> + };
>> + };
>> + };
>> };
>>
>> -&usb_1_qmpphy {
>> - status = "okay";
>> +&usb_1_dwc3 {
>> + dr_mode = "otg";
>> + usb-role-switch;
>> +};
>>
>> - vdda-phy-supply = <&vreg_l6b_1p2>;
>> - vdda-pll-supply = <&vreg_l1b_0p88>;
>> +&usb_1_dwc3_hs {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> +};
>> +
>> +&usb_1_dwc3_ss {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>> };
>>
>> &usb_2 {
>>
>> --
>> 2.34.1
>>
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node
@ 2023-02-13 12:41 ` Neil Armstrong
0 siblings, 0 replies; 52+ messages in thread
From: Neil Armstrong @ 2023-02-13 12:41 UTC (permalink / raw)
To: Bjorn Andersson
Cc: Heikki Krogerus, Greg Kroah-Hartman, Andy Gross, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
On 10/02/2023 21:13, Bjorn Andersson wrote:
> On Fri, Feb 10, 2023 at 04:02:11PM +0100, Neil Armstrong wrote:
>> Add the pmic glink node linked with the DWC3 USB controller
>> switched to OTG mode and tagged with usb-role-switch.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 77 ++++++++++++++++++++++++++++-----
>> 1 file changed, 65 insertions(+), 12 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> index 54654eb75c28..28fc9a835c5d 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
>> @@ -31,6 +31,40 @@ hdmi_con: endpoint {
>> };
>> };
>>
>> + pmic-glink {
>> + compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + connector@0 {
>> + compatible = "usb-c-connector";
>> + reg = <0>;
>> + power-role = "dual";
>> + data-role = "dual";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> +
>> + pmic_glink_hs_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_hs>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + pmic_glink_ss_in: endpoint {
>> + remote-endpoint = <&usb_1_dwc3_ss>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +
>> vph_pwr: vph-pwr-regulator {
>> compatible = "regulator-fixed";
>> regulator-name = "vph_pwr";
>> @@ -666,23 +700,42 @@ &usb_1 {
>> };
>>
>> &usb_1_dwc3 {
>> - /* TODO: Define USB-C connector properly */
>> - dr_mode = "peripheral";
>> -};
>> + dr_mode = "otg";
>> + usb-role-switch;
>>
>> -&usb_1_hsphy {
>> - status = "okay";
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>>
>> - vdda-pll-supply = <&vreg_l5b_0p88>;
>> - vdda18-supply = <&vreg_l1c_1p8>;
>> - vdda33-supply = <&vreg_l2b_3p07>;
>> + port@0 {
>> + reg = <0>;
>> +
>> + usb_1_dwc3_hs: endpoint {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> +
>> + usb_1_dwc3_ss: endpoint {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>
> The connector is indeed the next active component on the SuperSpeed
> lanes for USB. But as you're targeting to introduce QMP on that path,
> connector@0/port@1 would be pointing to QMP/ports/port@N.
>
> Do you plan to express the datapath between USB and QMP using this port
> at that time? (It's the correct thing to do...)
Yeah we need to figure out, because ultimately the datapath should be:
connector:
port0 --> usb_1_dwc3_hs
port1 --> qmpphy --> usb_1_dwc3_ss
port2 --> fsa4480 --> qmpphy -> dp_controller
And with a retimer, it gets even more complex:
connector:
port0 --> usb_1_dwc3_hs
port1 --> retimer --> qmpphy --> usb_1_dwc3_ss
port2 --> retimer --> qmpphy -> dp_controller
The solution I was using is instead of having chained port/endpoints,
I use multiple endpoints like :
port0 --> usb_1_dwc3_hs
port1 --> ep0: usb_1_dwc3_ss
ep1: qmpphy
port2 --> ep0: fsa4480
ep1: dp_controller
But I'm sure this is valid... but it is much simpler.
Neil
>
> Or will we not describe the SS lanes in this scenario?
>
> Regards,
> Bjorn
>
>> + };
>> + };
>> + };
>> };
>>
>> -&usb_1_qmpphy {
>> - status = "okay";
>> +&usb_1_dwc3 {
>> + dr_mode = "otg";
>> + usb-role-switch;
>> +};
>>
>> - vdda-phy-supply = <&vreg_l6b_1p2>;
>> - vdda-pll-supply = <&vreg_l1b_0p88>;
>> +&usb_1_dwc3_hs {
>> + remote-endpoint = <&pmic_glink_hs_in>;
>> +};
>> +
>> +&usb_1_dwc3_ss {
>> + remote-endpoint = <&pmic_glink_ss_in>;
>> };
>>
>> &usb_2 {
>>
>> --
>> 2.34.1
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 01/11] usb: typec: ucsi: add PMIC Glink UCSI driver
2023-02-10 15:02 ` Neil Armstrong
@ 2023-02-14 11:56 ` Heikki Krogerus
-1 siblings, 0 replies; 52+ messages in thread
From: Heikki Krogerus @ 2023-02-14 11:56 UTC (permalink / raw)
To: Neil Armstrong
Cc: Greg Kroah-Hartman, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
Hi,
I'm waiting for that other series that this depends on, but in the
meantime, there is one thing that has been bugging me...
On Fri, Feb 10, 2023 at 04:02:04PM +0100, Neil Armstrong wrote:
> diff --git a/drivers/usb/typec/ucsi/ucsi_glink.c b/drivers/usb/typec/ucsi/ucsi_glink.c
> new file mode 100644
> index 000000000000..9123f8a571e7
> --- /dev/null
> +++ b/drivers/usb/typec/ucsi/ucsi_glink.c
> @@ -0,0 +1,320 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022-2023, Linaro Ltd
> + */
Is that correct? Shouldn't it just be:
Copyright (c) 2023, Linaro Ltd
and that's it? Otherwise this look OK to me.
thanks,
--
heikki
^ permalink raw reply [flat|nested] 52+ messages in thread
* Re: [PATCH v2 01/11] usb: typec: ucsi: add PMIC Glink UCSI driver
@ 2023-02-14 11:56 ` Heikki Krogerus
0 siblings, 0 replies; 52+ messages in thread
From: Heikki Krogerus @ 2023-02-14 11:56 UTC (permalink / raw)
To: Neil Armstrong
Cc: Greg Kroah-Hartman, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Rob Herring, Krzysztof Kozlowski, Catalin Marinas, Will Deacon,
linux-kernel, linux-usb, linux-arm-msm, devicetree,
linux-arm-kernel
Hi,
I'm waiting for that other series that this depends on, but in the
meantime, there is one thing that has been bugging me...
On Fri, Feb 10, 2023 at 04:02:04PM +0100, Neil Armstrong wrote:
> diff --git a/drivers/usb/typec/ucsi/ucsi_glink.c b/drivers/usb/typec/ucsi/ucsi_glink.c
> new file mode 100644
> index 000000000000..9123f8a571e7
> --- /dev/null
> +++ b/drivers/usb/typec/ucsi/ucsi_glink.c
> @@ -0,0 +1,320 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022-2023, Linaro Ltd
> + */
Is that correct? Shouldn't it just be:
Copyright (c) 2023, Linaro Ltd
and that's it? Otherwise this look OK to me.
thanks,
--
heikki
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 52+ messages in thread
end of thread, other threads:[~2023-02-14 11:57 UTC | newest]
Thread overview: 52+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-02-10 15:02 [PATCH v2 00/11] soc: qcom: add UCSI function to PMIC GLINK Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:02 ` [PATCH v2 01/11] usb: typec: ucsi: add PMIC Glink UCSI driver Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-14 11:56 ` Heikki Krogerus
2023-02-14 11:56 ` Heikki Krogerus
2023-02-10 15:02 ` [PATCH v2 02/11] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:02 ` [PATCH v2 03/11] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:02 ` [PATCH v2 04/11] soc: qcom: pmic_glink: register ucsi aux device Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:41 ` Dmitry Baryshkov
2023-02-10 15:41 ` Dmitry Baryshkov
2023-02-10 20:10 ` Bjorn Andersson
2023-02-10 20:10 ` Bjorn Andersson
2023-02-10 15:02 ` [PATCH v2 05/11] arm64: dts: qcom: sm8350: add port subnodes in dwc3 node Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:19 ` Konrad Dybcio
2023-02-10 15:19 ` Konrad Dybcio
2023-02-10 15:02 ` [PATCH v2 06/11] arm64: dts: qcom: sm8450: " Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:19 ` Konrad Dybcio
2023-02-10 15:19 ` Konrad Dybcio
2023-02-10 15:02 ` [PATCH v2 07/11] arm64: dts: qcom: sm8550: " Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:19 ` Konrad Dybcio
2023-02-10 15:19 ` Konrad Dybcio
2023-02-10 15:02 ` [PATCH v2 08/11] arm64: dts: qcom: sm8350-hdk: add pmic glink node Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:21 ` Konrad Dybcio
2023-02-10 15:21 ` Konrad Dybcio
2023-02-10 15:26 ` Neil Armstrong
2023-02-10 15:26 ` Neil Armstrong
2023-02-10 15:44 ` Dmitry Baryshkov
2023-02-10 15:44 ` Dmitry Baryshkov
2023-02-10 20:13 ` Bjorn Andersson
2023-02-10 20:13 ` Bjorn Andersson
2023-02-13 12:41 ` Neil Armstrong
2023-02-13 12:41 ` Neil Armstrong
2023-02-10 15:02 ` [PATCH v2 09/11] arm64: dts: qcom: sm8450-hdk: " Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:22 ` Konrad Dybcio
2023-02-10 15:22 ` Konrad Dybcio
2023-02-10 15:02 ` [PATCH v2 10/11] arm64: dts: qcom: sm8550-mtp: " Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:22 ` Konrad Dybcio
2023-02-10 15:22 ` Konrad Dybcio
2023-02-10 15:02 ` [PATCH v2 11/11] arm64: defconfig: add PMIC GLINK modules Neil Armstrong
2023-02-10 15:02 ` Neil Armstrong
2023-02-10 15:22 ` Konrad Dybcio
2023-02-10 15:22 ` Konrad Dybcio
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.