[PATCHv1 0/5] Add RK3588 SATA support

[PATCHv1 0/5] Add RK3588 SATA support

[Sebastian Reichel]

Hi,

This enables SATA support for RK3588.

-- Sebastian

Sebastian Reichel (5):
  dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon
  dt-bindings: ata: ahci: add RK3588 AHCI controller
  dt-bindings: phy: rockchip: rk3588 has two reset lines
  arm64: dts: rockchip: rk3588: add combo PHYs
  arm64: dts: rockchip: rk3588: add SATA support

 .../bindings/ata/snps,dwc-ahci-common.yaml    |  6 +-
 .../bindings/ata/snps,dwc-ahci.yaml           |  6 +-
 .../phy/phy-rockchip-naneng-combphy.yaml      |  7 +-
 .../devicetree/bindings/soc/rockchip/grf.yaml |  1 +
 arch/arm64/boot/dts/rockchip/rk3588.dtsi      | 44 +++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi     | 90 +++++++++++++++++++
 6 files changed, 149 insertions(+), 5 deletions(-)

-- 
2.39.2

[PATCHv1 0/5] Add RK3588 SATA support

[Sebastian Reichel]

Hi,

This enables SATA support for RK3588.

-- Sebastian

Sebastian Reichel (5):
  dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon
  dt-bindings: ata: ahci: add RK3588 AHCI controller
  dt-bindings: phy: rockchip: rk3588 has two reset lines
  arm64: dts: rockchip: rk3588: add combo PHYs
  arm64: dts: rockchip: rk3588: add SATA support

 .../bindings/ata/snps,dwc-ahci-common.yaml    |  6 +-
 .../bindings/ata/snps,dwc-ahci.yaml           |  6 +-
 .../phy/phy-rockchip-naneng-combphy.yaml      |  7 +-
 .../devicetree/bindings/soc/rockchip/grf.yaml |  1 +
 arch/arm64/boot/dts/rockchip/rk3588.dtsi      | 44 +++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi     | 90 +++++++++++++++++++
 6 files changed, 149 insertions(+), 5 deletions(-)

-- 
2.39.2


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCHv1 0/5] Add RK3588 SATA support

[Sebastian Reichel]

Hi,

This enables SATA support for RK3588.

-- Sebastian

Sebastian Reichel (5):
  dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon
  dt-bindings: ata: ahci: add RK3588 AHCI controller
  dt-bindings: phy: rockchip: rk3588 has two reset lines
  arm64: dts: rockchip: rk3588: add combo PHYs
  arm64: dts: rockchip: rk3588: add SATA support

 .../bindings/ata/snps,dwc-ahci-common.yaml    |  6 +-
 .../bindings/ata/snps,dwc-ahci.yaml           |  6 +-
 .../phy/phy-rockchip-naneng-combphy.yaml      |  7 +-
 .../devicetree/bindings/soc/rockchip/grf.yaml |  1 +
 arch/arm64/boot/dts/rockchip/rk3588.dtsi      | 44 +++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi     | 90 +++++++++++++++++++
 6 files changed, 149 insertions(+), 5 deletions(-)

-- 
2.39.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCHv1 1/5] dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon

[Sebastian Reichel]

The pipe-phy syscon is used by rockchip,rk3588-naneng-combphy,
which in turn is the PHY for USB3, PCIe and SATA.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
index a873f74564f2..dda071b66813 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -24,6 +24,7 @@ properties:
               - rockchip,rk3588-bigcore1-grf
               - rockchip,rk3588-ioc
               - rockchip,rk3588-php-grf
+              - rockchip,rk3588-pipe-phy-grf
               - rockchip,rk3588-sys-grf
               - rockchip,rk3588-pcie3-phy-grf
               - rockchip,rk3588-pcie3-pipe-grf
-- 
2.39.2

[PATCHv1 1/5] dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon

[Sebastian Reichel]

The pipe-phy syscon is used by rockchip,rk3588-naneng-combphy,
which in turn is the PHY for USB3, PCIe and SATA.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
index a873f74564f2..dda071b66813 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -24,6 +24,7 @@ properties:
               - rockchip,rk3588-bigcore1-grf
               - rockchip,rk3588-ioc
               - rockchip,rk3588-php-grf
+              - rockchip,rk3588-pipe-phy-grf
               - rockchip,rk3588-sys-grf
               - rockchip,rk3588-pcie3-phy-grf
               - rockchip,rk3588-pcie3-pipe-grf
-- 
2.39.2


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCHv1 1/5] dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon

[Sebastian Reichel]

The pipe-phy syscon is used by rockchip,rk3588-naneng-combphy,
which in turn is the PHY for USB3, PCIe and SATA.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
index a873f74564f2..dda071b66813 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.yaml
@@ -24,6 +24,7 @@ properties:
               - rockchip,rk3588-bigcore1-grf
               - rockchip,rk3588-ioc
               - rockchip,rk3588-php-grf
+              - rockchip,rk3588-pipe-phy-grf
               - rockchip,rk3588-sys-grf
               - rockchip,rk3588-pcie3-phy-grf
               - rockchip,rk3588-pcie3-pipe-grf
-- 
2.39.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Sebastian Reichel]

Just like RK3568, the RK3588 has a DWC based AHCI controller.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
details unfortunately. It is required for functional SATA, though.
---
 .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
 Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
 2 files changed, 8 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
index c1457910520b..0df8f49431eb 100644
--- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
+++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
@@ -31,11 +31,11 @@ properties:
       PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
       clock, etc.
     minItems: 1
-    maxItems: 4
+    maxItems: 5
 
   clock-names:
     minItems: 1
-    maxItems: 4
+    maxItems: 5
     items:
       oneOf:
         - description: Application APB/AHB/AXI BIU clock
@@ -50,6 +50,8 @@ properties:
           const: rxoob
         - description: SATA Ports reference clock
           const: ref
+        - description: Rockchip ASIC clock
+          const: asic
 
   resets:
     description:
diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
index 5afa4b57ce20..c6a0d6c8b62c 100644
--- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
+++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
@@ -23,9 +23,11 @@ properties:
         const: snps,dwc-ahci
       - description: SPEAr1340 AHCI SATA device
         const: snps,spear-ahci
-      - description: Rockhip RK3568 AHCI controller
+      - description: Rockhip AHCI controller
         items:
-          - const: rockchip,rk3568-dwc-ahci
+          - enum:
+              - rockchip,rk3568-dwc-ahci
+              - rockchip,rk3588-dwc-ahci
           - const: snps,dwc-ahci
 
 patternProperties:
-- 
2.39.2

[PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Sebastian Reichel]

Just like RK3568, the RK3588 has a DWC based AHCI controller.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
details unfortunately. It is required for functional SATA, though.
---
 .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
 Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
 2 files changed, 8 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
index c1457910520b..0df8f49431eb 100644
--- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
+++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
@@ -31,11 +31,11 @@ properties:
       PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
       clock, etc.
     minItems: 1
-    maxItems: 4
+    maxItems: 5
 
   clock-names:
     minItems: 1
-    maxItems: 4
+    maxItems: 5
     items:
       oneOf:
         - description: Application APB/AHB/AXI BIU clock
@@ -50,6 +50,8 @@ properties:
           const: rxoob
         - description: SATA Ports reference clock
           const: ref
+        - description: Rockchip ASIC clock
+          const: asic
 
   resets:
     description:
diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
index 5afa4b57ce20..c6a0d6c8b62c 100644
--- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
+++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
@@ -23,9 +23,11 @@ properties:
         const: snps,dwc-ahci
       - description: SPEAr1340 AHCI SATA device
         const: snps,spear-ahci
-      - description: Rockhip RK3568 AHCI controller
+      - description: Rockhip AHCI controller
         items:
-          - const: rockchip,rk3568-dwc-ahci
+          - enum:
+              - rockchip,rk3568-dwc-ahci
+              - rockchip,rk3588-dwc-ahci
           - const: snps,dwc-ahci
 
 patternProperties:
-- 
2.39.2


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Sebastian Reichel]

Just like RK3568, the RK3588 has a DWC based AHCI controller.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
details unfortunately. It is required for functional SATA, though.
---
 .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
 Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
 2 files changed, 8 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
index c1457910520b..0df8f49431eb 100644
--- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
+++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
@@ -31,11 +31,11 @@ properties:
       PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
       clock, etc.
     minItems: 1
-    maxItems: 4
+    maxItems: 5
 
   clock-names:
     minItems: 1
-    maxItems: 4
+    maxItems: 5
     items:
       oneOf:
         - description: Application APB/AHB/AXI BIU clock
@@ -50,6 +50,8 @@ properties:
           const: rxoob
         - description: SATA Ports reference clock
           const: ref
+        - description: Rockchip ASIC clock
+          const: asic
 
   resets:
     description:
diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
index 5afa4b57ce20..c6a0d6c8b62c 100644
--- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
+++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
@@ -23,9 +23,11 @@ properties:
         const: snps,dwc-ahci
       - description: SPEAr1340 AHCI SATA device
         const: snps,spear-ahci
-      - description: Rockhip RK3568 AHCI controller
+      - description: Rockhip AHCI controller
         items:
-          - const: rockchip,rk3568-dwc-ahci
+          - enum:
+              - rockchip,rk3568-dwc-ahci
+              - rockchip,rk3588-dwc-ahci
           - const: snps,dwc-ahci
 
 patternProperties:
-- 
2.39.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Sebastian Reichel]

The RK3588 has two reset lines for the combphy. One for the
APB interface and one for the actual PHY.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
index 9ae514fa7533..bac1aae07555 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
@@ -31,8 +31,13 @@ properties:
       - const: pipe
 
   resets:
+    minItems: 1
+    maxItems: 2
+
+  reset-names:
     items:
-      - description: exclusive PHY reset line
+      - const: phy
+      - const: apb
 
   rockchip,enable-ssc:
     type: boolean
-- 
2.39.2

[PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Sebastian Reichel]

The RK3588 has two reset lines for the combphy. One for the
APB interface and one for the actual PHY.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
index 9ae514fa7533..bac1aae07555 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
@@ -31,8 +31,13 @@ properties:
       - const: pipe
 
   resets:
+    minItems: 1
+    maxItems: 2
+
+  reset-names:
     items:
-      - description: exclusive PHY reset line
+      - const: phy
+      - const: apb
 
   rockchip,enable-ssc:
     type: boolean
-- 
2.39.2


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Sebastian Reichel]

The RK3588 has two reset lines for the combphy. One for the
APB interface and one for the actual PHY.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
index 9ae514fa7533..bac1aae07555 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
@@ -31,8 +31,13 @@ properties:
       - const: pipe
 
   resets:
+    minItems: 1
+    maxItems: 2
+
+  reset-names:
     items:
-      - description: exclusive PHY reset line
+      - const: phy
+      - const: apb
 
   rockchip,enable-ssc:
     type: boolean
-- 
2.39.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCHv1 4/5] arm64: dts: rockchip: rk3588: add combo PHYs

[Sebastian Reichel]

Add all 3 combo PHYs that can be found in RK3588.
They are used for SATA, PCIe or USB3.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3588.dtsi  | 21 ++++++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 42 +++++++++++++++++++++++
 2 files changed, 63 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
index d085e57fbc4c..fe1866a3697a 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
@@ -7,6 +7,11 @@
 #include "rk3588-pinctrl.dtsi"
 
 / {
+	pipe_phy1_grf: syscon@fd5c0000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5c0000 0x0 0x100>;
+	};
+
 	gmac0: ethernet@fe1b0000 {
 		compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a";
 		reg = <0x0 0xfe1b0000 0x0 0x10000>;
@@ -55,4 +60,20 @@ gmac0_mtl_tx_setup: tx-queues-config {
 			queue1 {};
 		};
 	};
+
+	combphy1_ps: phy@fee10000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee10000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY1>, <&cru PCLK_PCIE_COMBO_PIPE_PHY1>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY1>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY1>, <&cru SRST_P_PCIE2_PHY1>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy1_grf>;
+		status = "disabled";
+	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
index 422b31e342ca..7227c918f825 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
@@ -944,6 +944,16 @@ php_grf: syscon@fd5b0000 {
 		reg = <0x0 0xfd5b0000 0x0 0x1000>;
 	};
 
+	pipe_phy0_grf: syscon@fd5bc000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5bc000 0x0 0x100>;
+	};
+
+	pipe_phy2_grf: syscon@fd5c4000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5c4000 0x0 0x100>;
+	};
+
 	ioc: syscon@fd5f0000 {
 		compatible = "rockchip,rk3588-ioc", "syscon";
 		reg = <0x0 0xfd5f0000 0x0 0x10000>;
@@ -2200,6 +2210,38 @@ dmac2: dma-controller@fed10000 {
 		#dma-cells = <1>;
 	};
 
+	combphy0_ps: phy@fee00000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee00000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY0>, <&cru PCLK_PCIE_COMBO_PIPE_PHY0>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY0>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY0>, <&cru SRST_P_PCIE2_PHY0>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy0_grf>;
+		status = "disabled";
+	};
+
+	combphy2_psu: phy@fee20000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee20000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY2>, <&cru PCLK_PCIE_COMBO_PIPE_PHY2>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY2>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY2>, <&cru SRST_P_PCIE2_PHY2>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy2_grf>;
+		status = "disabled";
+	};
+
 	system_sram2: sram@ff001000 {
 		compatible = "mmio-sram";
 		reg = <0x0 0xff001000 0x0 0xef000>;
-- 
2.39.2

[PATCHv1 4/5] arm64: dts: rockchip: rk3588: add combo PHYs

[Sebastian Reichel]

Add all 3 combo PHYs that can be found in RK3588.
They are used for SATA, PCIe or USB3.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3588.dtsi  | 21 ++++++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 42 +++++++++++++++++++++++
 2 files changed, 63 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
index d085e57fbc4c..fe1866a3697a 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
@@ -7,6 +7,11 @@
 #include "rk3588-pinctrl.dtsi"
 
 / {
+	pipe_phy1_grf: syscon@fd5c0000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5c0000 0x0 0x100>;
+	};
+
 	gmac0: ethernet@fe1b0000 {
 		compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a";
 		reg = <0x0 0xfe1b0000 0x0 0x10000>;
@@ -55,4 +60,20 @@ gmac0_mtl_tx_setup: tx-queues-config {
 			queue1 {};
 		};
 	};
+
+	combphy1_ps: phy@fee10000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee10000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY1>, <&cru PCLK_PCIE_COMBO_PIPE_PHY1>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY1>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY1>, <&cru SRST_P_PCIE2_PHY1>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy1_grf>;
+		status = "disabled";
+	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
index 422b31e342ca..7227c918f825 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
@@ -944,6 +944,16 @@ php_grf: syscon@fd5b0000 {
 		reg = <0x0 0xfd5b0000 0x0 0x1000>;
 	};
 
+	pipe_phy0_grf: syscon@fd5bc000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5bc000 0x0 0x100>;
+	};
+
+	pipe_phy2_grf: syscon@fd5c4000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5c4000 0x0 0x100>;
+	};
+
 	ioc: syscon@fd5f0000 {
 		compatible = "rockchip,rk3588-ioc", "syscon";
 		reg = <0x0 0xfd5f0000 0x0 0x10000>;
@@ -2200,6 +2210,38 @@ dmac2: dma-controller@fed10000 {
 		#dma-cells = <1>;
 	};
 
+	combphy0_ps: phy@fee00000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee00000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY0>, <&cru PCLK_PCIE_COMBO_PIPE_PHY0>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY0>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY0>, <&cru SRST_P_PCIE2_PHY0>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy0_grf>;
+		status = "disabled";
+	};
+
+	combphy2_psu: phy@fee20000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee20000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY2>, <&cru PCLK_PCIE_COMBO_PIPE_PHY2>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY2>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY2>, <&cru SRST_P_PCIE2_PHY2>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy2_grf>;
+		status = "disabled";
+	};
+
 	system_sram2: sram@ff001000 {
 		compatible = "mmio-sram";
 		reg = <0x0 0xff001000 0x0 0xef000>;
-- 
2.39.2


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCHv1 4/5] arm64: dts: rockchip: rk3588: add combo PHYs

[Sebastian Reichel]

Add all 3 combo PHYs that can be found in RK3588.
They are used for SATA, PCIe or USB3.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3588.dtsi  | 21 ++++++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 42 +++++++++++++++++++++++
 2 files changed, 63 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
index d085e57fbc4c..fe1866a3697a 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
@@ -7,6 +7,11 @@
 #include "rk3588-pinctrl.dtsi"
 
 / {
+	pipe_phy1_grf: syscon@fd5c0000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5c0000 0x0 0x100>;
+	};
+
 	gmac0: ethernet@fe1b0000 {
 		compatible = "rockchip,rk3588-gmac", "snps,dwmac-4.20a";
 		reg = <0x0 0xfe1b0000 0x0 0x10000>;
@@ -55,4 +60,20 @@ gmac0_mtl_tx_setup: tx-queues-config {
 			queue1 {};
 		};
 	};
+
+	combphy1_ps: phy@fee10000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee10000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY1>, <&cru PCLK_PCIE_COMBO_PIPE_PHY1>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY1>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY1>, <&cru SRST_P_PCIE2_PHY1>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy1_grf>;
+		status = "disabled";
+	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
index 422b31e342ca..7227c918f825 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
@@ -944,6 +944,16 @@ php_grf: syscon@fd5b0000 {
 		reg = <0x0 0xfd5b0000 0x0 0x1000>;
 	};
 
+	pipe_phy0_grf: syscon@fd5bc000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5bc000 0x0 0x100>;
+	};
+
+	pipe_phy2_grf: syscon@fd5c4000 {
+		compatible = "rockchip,rk3588-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfd5c4000 0x0 0x100>;
+	};
+
 	ioc: syscon@fd5f0000 {
 		compatible = "rockchip,rk3588-ioc", "syscon";
 		reg = <0x0 0xfd5f0000 0x0 0x10000>;
@@ -2200,6 +2210,38 @@ dmac2: dma-controller@fed10000 {
 		#dma-cells = <1>;
 	};
 
+	combphy0_ps: phy@fee00000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee00000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY0>, <&cru PCLK_PCIE_COMBO_PIPE_PHY0>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY0>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY0>, <&cru SRST_P_PCIE2_PHY0>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy0_grf>;
+		status = "disabled";
+	};
+
+	combphy2_psu: phy@fee20000 {
+		compatible = "rockchip,rk3588-naneng-combphy";
+		reg = <0x0 0xfee20000 0x0 0x100>;
+		#phy-cells = <1>;
+		clocks = <&cru CLK_REF_PIPE_PHY2>, <&cru PCLK_PCIE_COMBO_PIPE_PHY2>,
+			 <&cru PCLK_PHP_ROOT>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&cru CLK_REF_PIPE_PHY2>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_REF_PIPE_PHY2>, <&cru SRST_P_PCIE2_PHY2>;
+		reset-names = "phy", "apb";
+		rockchip,pipe-grf = <&php_grf>;
+		rockchip,pipe-phy-grf = <&pipe_phy2_grf>;
+		status = "disabled";
+	};
+
 	system_sram2: sram@ff001000 {
 		compatible = "mmio-sram";
 		reg = <0x0 0xff001000 0x0 0xef000>;
-- 
2.39.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCHv1 5/5] arm64: dts: rockchip: rk3588: add SATA support

[Sebastian Reichel]

Add all three SATA IP blocks to the RK3588 DT.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3588.dtsi  | 23 +++++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 48 +++++++++++++++++++++++
 2 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
index fe1866a3697a..65d818964bff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
@@ -61,6 +61,29 @@ gmac0_mtl_tx_setup: tx-queues-config {
 		};
 	};
 
+	sata1: sata@fe220000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe220000 0 0x1000>;
+		clocks = <&cru ACLK_SATA1>, <&cru CLK_PMALIVE1>,
+			 <&cru CLK_RXOOB1>, <&cru CLK_PIPEPHY1_REF>,
+			 <&cru CLK_PIPEPHY1_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy1_ps PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
 	combphy1_ps: phy@fee10000 {
 		compatible = "rockchip,rk3588-naneng-combphy";
 		reg = <0x0 0xfee10000 0x0 0x100>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
index 7227c918f825..2124c654f665 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
@@ -9,6 +9,8 @@
 #include <dt-bindings/power/rk3588-power.h>
 #include <dt-bindings/reset/rockchip,rk3588-cru.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/ata/ahci.h>
 
 / {
 	compatible = "rockchip,rk3588";
@@ -1666,6 +1668,52 @@ gmac1_mtl_tx_setup: tx-queues-config {
 		};
 	};
 
+	sata0: sata@fe210000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe210000 0 0x1000>;
+		clocks = <&cru ACLK_SATA0>, <&cru CLK_PMALIVE0>,
+			 <&cru CLK_RXOOB0>, <&cru CLK_PIPEPHY0_REF>,
+			 <&cru CLK_PIPEPHY0_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy0_ps PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
+	sata2: sata@fe230000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe230000 0 0x1000>;
+		clocks = <&cru ACLK_SATA2>, <&cru CLK_PMALIVE2>,
+			 <&cru CLK_RXOOB2>, <&cru CLK_PIPEPHY2_REF>,
+			 <&cru CLK_PIPEPHY2_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy2_psu PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
 	sdhci: mmc@fe2e0000 {
 		compatible = "rockchip,rk3588-dwcmshc";
 		reg = <0x0 0xfe2e0000 0x0 0x10000>;
-- 
2.39.2

[PATCHv1 5/5] arm64: dts: rockchip: rk3588: add SATA support

[Sebastian Reichel]

Add all three SATA IP blocks to the RK3588 DT.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3588.dtsi  | 23 +++++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 48 +++++++++++++++++++++++
 2 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
index fe1866a3697a..65d818964bff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
@@ -61,6 +61,29 @@ gmac0_mtl_tx_setup: tx-queues-config {
 		};
 	};
 
+	sata1: sata@fe220000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe220000 0 0x1000>;
+		clocks = <&cru ACLK_SATA1>, <&cru CLK_PMALIVE1>,
+			 <&cru CLK_RXOOB1>, <&cru CLK_PIPEPHY1_REF>,
+			 <&cru CLK_PIPEPHY1_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy1_ps PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
 	combphy1_ps: phy@fee10000 {
 		compatible = "rockchip,rk3588-naneng-combphy";
 		reg = <0x0 0xfee10000 0x0 0x100>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
index 7227c918f825..2124c654f665 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
@@ -9,6 +9,8 @@
 #include <dt-bindings/power/rk3588-power.h>
 #include <dt-bindings/reset/rockchip,rk3588-cru.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/ata/ahci.h>
 
 / {
 	compatible = "rockchip,rk3588";
@@ -1666,6 +1668,52 @@ gmac1_mtl_tx_setup: tx-queues-config {
 		};
 	};
 
+	sata0: sata@fe210000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe210000 0 0x1000>;
+		clocks = <&cru ACLK_SATA0>, <&cru CLK_PMALIVE0>,
+			 <&cru CLK_RXOOB0>, <&cru CLK_PIPEPHY0_REF>,
+			 <&cru CLK_PIPEPHY0_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy0_ps PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
+	sata2: sata@fe230000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe230000 0 0x1000>;
+		clocks = <&cru ACLK_SATA2>, <&cru CLK_PMALIVE2>,
+			 <&cru CLK_RXOOB2>, <&cru CLK_PIPEPHY2_REF>,
+			 <&cru CLK_PIPEPHY2_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy2_psu PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
 	sdhci: mmc@fe2e0000 {
 		compatible = "rockchip,rk3588-dwcmshc";
 		reg = <0x0 0xfe2e0000 0x0 0x10000>;
-- 
2.39.2


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCHv1 5/5] arm64: dts: rockchip: rk3588: add SATA support

[Sebastian Reichel]

Add all three SATA IP blocks to the RK3588 DT.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3588.dtsi  | 23 +++++++++++
 arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 48 +++++++++++++++++++++++
 2 files changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588.dtsi b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
index fe1866a3697a..65d818964bff 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588.dtsi
@@ -61,6 +61,29 @@ gmac0_mtl_tx_setup: tx-queues-config {
 		};
 	};
 
+	sata1: sata@fe220000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe220000 0 0x1000>;
+		clocks = <&cru ACLK_SATA1>, <&cru CLK_PMALIVE1>,
+			 <&cru CLK_RXOOB1>, <&cru CLK_PIPEPHY1_REF>,
+			 <&cru CLK_PIPEPHY1_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy1_ps PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
 	combphy1_ps: phy@fee10000 {
 		compatible = "rockchip,rk3588-naneng-combphy";
 		reg = <0x0 0xfee10000 0x0 0x100>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
index 7227c918f825..2124c654f665 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
@@ -9,6 +9,8 @@
 #include <dt-bindings/power/rk3588-power.h>
 #include <dt-bindings/reset/rockchip,rk3588-cru.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/ata/ahci.h>
 
 / {
 	compatible = "rockchip,rk3588";
@@ -1666,6 +1668,52 @@ gmac1_mtl_tx_setup: tx-queues-config {
 		};
 	};
 
+	sata0: sata@fe210000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe210000 0 0x1000>;
+		clocks = <&cru ACLK_SATA0>, <&cru CLK_PMALIVE0>,
+			 <&cru CLK_RXOOB0>, <&cru CLK_PIPEPHY0_REF>,
+			 <&cru CLK_PIPEPHY0_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy0_ps PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
+	sata2: sata@fe230000 {
+		compatible = "rockchip,rk3588-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfe230000 0 0x1000>;
+		clocks = <&cru ACLK_SATA2>, <&cru CLK_PMALIVE2>,
+			 <&cru CLK_RXOOB2>, <&cru CLK_PIPEPHY2_REF>,
+			 <&cru CLK_PIPEPHY2_PIPE_ASIC_G>;
+		clock-names = "sata", "pmalive", "rxoob", "ref", "asic";
+		interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH 0>;
+		ports-implemented = <0x1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		sata-port@0 {
+			reg = <0>;
+			hba-port-cap = <HBA_PORT_FBSCP>;
+			phys = <&combphy2_psu PHY_TYPE_SATA>;
+			phy-names = "sata-phy";
+			snps,rx-ts-max = <32>;
+			snps,tx-ts-max = <32>;
+		};
+	};
+
 	sdhci: mmc@fe2e0000 {
 		compatible = "rockchip,rk3588-dwcmshc";
 		reg = <0x0 0xfe2e0000 0x0 0x10000>;
-- 
2.39.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Damien Le Moal]

On 4/14/23 03:23, Sebastian Reichel wrote:
> Just like RK3568, the RK3588 has a DWC based AHCI controller.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
> details unfortunately. It is required for functional SATA, though.
> ---
>  .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
>  Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
>  2 files changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> index c1457910520b..0df8f49431eb 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> @@ -31,11 +31,11 @@ properties:
>        PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
>        clock, etc.
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>  
>    clock-names:
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>      items:
>        oneOf:
>          - description: Application APB/AHB/AXI BIU clock
> @@ -50,6 +50,8 @@ properties:
>            const: rxoob
>          - description: SATA Ports reference clock
>            const: ref
> +        - description: Rockchip ASIC clock

Shouldn't this mention that this clock is for the 3588 only ? Or is it also
necessary for the 3568 ? That is not super clear.

> +          const: asic
>  
>    resets:
>      description:
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> index 5afa4b57ce20..c6a0d6c8b62c 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> @@ -23,9 +23,11 @@ properties:
>          const: snps,dwc-ahci
>        - description: SPEAr1340 AHCI SATA device
>          const: snps,spear-ahci
> -      - description: Rockhip RK3568 AHCI controller
> +      - description: Rockhip AHCI controller
>          items:
> -          - const: rockchip,rk3568-dwc-ahci
> +          - enum:
> +              - rockchip,rk3568-dwc-ahci
> +              - rockchip,rk3588-dwc-ahci
>            - const: snps,dwc-ahci
>  
>  patternProperties:

Re: [PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Damien Le Moal]

On 4/14/23 03:23, Sebastian Reichel wrote:
> Just like RK3568, the RK3588 has a DWC based AHCI controller.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
> details unfortunately. It is required for functional SATA, though.
> ---
>  .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
>  Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
>  2 files changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> index c1457910520b..0df8f49431eb 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> @@ -31,11 +31,11 @@ properties:
>        PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
>        clock, etc.
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>  
>    clock-names:
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>      items:
>        oneOf:
>          - description: Application APB/AHB/AXI BIU clock
> @@ -50,6 +50,8 @@ properties:
>            const: rxoob
>          - description: SATA Ports reference clock
>            const: ref
> +        - description: Rockchip ASIC clock

Shouldn't this mention that this clock is for the 3588 only ? Or is it also
necessary for the 3568 ? That is not super clear.

> +          const: asic
>  
>    resets:
>      description:
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> index 5afa4b57ce20..c6a0d6c8b62c 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> @@ -23,9 +23,11 @@ properties:
>          const: snps,dwc-ahci
>        - description: SPEAr1340 AHCI SATA device
>          const: snps,spear-ahci
> -      - description: Rockhip RK3568 AHCI controller
> +      - description: Rockhip AHCI controller
>          items:
> -          - const: rockchip,rk3568-dwc-ahci
> +          - enum:
> +              - rockchip,rk3568-dwc-ahci
> +              - rockchip,rk3588-dwc-ahci
>            - const: snps,dwc-ahci
>  
>  patternProperties:


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Damien Le Moal]

On 4/14/23 03:23, Sebastian Reichel wrote:
> Just like RK3568, the RK3588 has a DWC based AHCI controller.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
> details unfortunately. It is required for functional SATA, though.
> ---
>  .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
>  Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
>  2 files changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> index c1457910520b..0df8f49431eb 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> @@ -31,11 +31,11 @@ properties:
>        PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
>        clock, etc.
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>  
>    clock-names:
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>      items:
>        oneOf:
>          - description: Application APB/AHB/AXI BIU clock
> @@ -50,6 +50,8 @@ properties:
>            const: rxoob
>          - description: SATA Ports reference clock
>            const: ref
> +        - description: Rockchip ASIC clock

Shouldn't this mention that this clock is for the 3588 only ? Or is it also
necessary for the 3568 ? That is not super clear.

> +          const: asic
>  
>    resets:
>      description:
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> index 5afa4b57ce20..c6a0d6c8b62c 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> @@ -23,9 +23,11 @@ properties:
>          const: snps,dwc-ahci
>        - description: SPEAr1340 AHCI SATA device
>          const: snps,spear-ahci
> -      - description: Rockhip RK3568 AHCI controller
> +      - description: Rockhip AHCI controller
>          items:
> -          - const: rockchip,rk3568-dwc-ahci
> +          - enum:
> +              - rockchip,rk3568-dwc-ahci
> +              - rockchip,rk3588-dwc-ahci
>            - const: snps,dwc-ahci
>  
>  patternProperties:


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCHv1 1/5] dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon

[Rob Herring]

On Thu, 13 Apr 2023 20:23:41 +0200, Sebastian Reichel wrote:
> The pipe-phy syscon is used by rockchip,rk3588-naneng-combphy,
> which in turn is the PHY for USB3, PCIe and SATA.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCHv1 1/5] dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon

[Rob Herring]

On Thu, 13 Apr 2023 20:23:41 +0200, Sebastian Reichel wrote:
> The pipe-phy syscon is used by rockchip,rk3588-naneng-combphy,
> which in turn is the PHY for USB3, PCIe and SATA.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCHv1 1/5] dt-bindings: soc: rockchip: add rk3588 pipe-phy syscon

[Rob Herring]

On Thu, 13 Apr 2023 20:23:41 +0200, Sebastian Reichel wrote:
> The pipe-phy syscon is used by rockchip,rk3588-naneng-combphy,
> which in turn is the PHY for USB3, PCIe and SATA.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring <robh@kernel.org>


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Rob Herring]

On Thu, Apr 13, 2023 at 08:23:43PM +0200, Sebastian Reichel wrote:
> The RK3588 has two reset lines for the combphy. One for the
> APB interface and one for the actual PHY.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
>  1 file changed, 6 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> index 9ae514fa7533..bac1aae07555 100644
> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> @@ -31,8 +31,13 @@ properties:
>        - const: pipe
>  
>    resets:
> +    minItems: 1
> +    maxItems: 2
> +
> +  reset-names:
>      items:
> -      - description: exclusive PHY reset line
> +      - const: phy
> +      - const: apb

This will fail on any existing users with single entry. You need to add 
'minItems: 1' here.

It also fails if they didn't use 'phy' as the name, but names should be 
defined.

Rob

Re: [PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Rob Herring]

On Thu, Apr 13, 2023 at 08:23:43PM +0200, Sebastian Reichel wrote:
> The RK3588 has two reset lines for the combphy. One for the
> APB interface and one for the actual PHY.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
>  1 file changed, 6 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> index 9ae514fa7533..bac1aae07555 100644
> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> @@ -31,8 +31,13 @@ properties:
>        - const: pipe
>  
>    resets:
> +    minItems: 1
> +    maxItems: 2
> +
> +  reset-names:
>      items:
> -      - description: exclusive PHY reset line
> +      - const: phy
> +      - const: apb

This will fail on any existing users with single entry. You need to add 
'minItems: 1' here.

It also fails if they didn't use 'phy' as the name, but names should be 
defined.

Rob

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Rob Herring]

On Thu, Apr 13, 2023 at 08:23:43PM +0200, Sebastian Reichel wrote:
> The RK3588 has two reset lines for the combphy. One for the
> APB interface and one for the actual PHY.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
>  1 file changed, 6 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> index 9ae514fa7533..bac1aae07555 100644
> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> @@ -31,8 +31,13 @@ properties:
>        - const: pipe
>  
>    resets:
> +    minItems: 1
> +    maxItems: 2
> +
> +  reset-names:
>      items:
> -      - description: exclusive PHY reset line
> +      - const: phy
> +      - const: apb

This will fail on any existing users with single entry. You need to add 
'minItems: 1' here.

It also fails if they didn't use 'phy' as the name, but names should be 
defined.

Rob

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Sebastian Reichel]

[-- Attachment #1: Type: text/plain, Size: 1575 bytes --]

Hello Rob,

On Tue, Apr 18, 2023 at 03:41:36PM -0500, Rob Herring wrote:
> On Thu, Apr 13, 2023 at 08:23:43PM +0200, Sebastian Reichel wrote:
> > The RK3588 has two reset lines for the combphy. One for the
> > APB interface and one for the actual PHY.
> > 
> > Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> > ---
> >  .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
> >  1 file changed, 6 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > index 9ae514fa7533..bac1aae07555 100644
> > --- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > @@ -31,8 +31,13 @@ properties:
> >        - const: pipe
> >  
> >    resets:
> > +    minItems: 1
> > +    maxItems: 2
> > +
> > +  reset-names:
> >      items:
> > -      - description: exclusive PHY reset line
> > +      - const: phy
> > +      - const: apb
> 
> This will fail on any existing users with single entry. You need to add 
> 'minItems: 1' here.
> 
> It also fails if they didn't use 'phy' as the name, but names should be 
> defined.

My understanding is, there there currently are users with one entry
and no reset-names. I suppose its sensible not to provide a
reset-name, iff there is only one line. As far as I can tell that
should still work after my changes.

-- Sebastian

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Sebastian Reichel]

[-- Attachment #1.1: Type: text/plain, Size: 1575 bytes --]

Hello Rob,

On Tue, Apr 18, 2023 at 03:41:36PM -0500, Rob Herring wrote:
> On Thu, Apr 13, 2023 at 08:23:43PM +0200, Sebastian Reichel wrote:
> > The RK3588 has two reset lines for the combphy. One for the
> > APB interface and one for the actual PHY.
> > 
> > Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> > ---
> >  .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
> >  1 file changed, 6 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > index 9ae514fa7533..bac1aae07555 100644
> > --- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > @@ -31,8 +31,13 @@ properties:
> >        - const: pipe
> >  
> >    resets:
> > +    minItems: 1
> > +    maxItems: 2
> > +
> > +  reset-names:
> >      items:
> > -      - description: exclusive PHY reset line
> > +      - const: phy
> > +      - const: apb
> 
> This will fail on any existing users with single entry. You need to add 
> 'minItems: 1' here.
> 
> It also fails if they didn't use 'phy' as the name, but names should be 
> defined.

My understanding is, there there currently are users with one entry
and no reset-names. I suppose its sensible not to provide a
reset-name, iff there is only one line. As far as I can tell that
should still work after my changes.

-- Sebastian

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

[-- Attachment #2: Type: text/plain, Size: 112 bytes --]

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCHv1 3/5] dt-bindings: phy: rockchip: rk3588 has two reset lines

[Sebastian Reichel]

[-- Attachment #1.1: Type: text/plain, Size: 1575 bytes --]

Hello Rob,

On Tue, Apr 18, 2023 at 03:41:36PM -0500, Rob Herring wrote:
> On Thu, Apr 13, 2023 at 08:23:43PM +0200, Sebastian Reichel wrote:
> > The RK3588 has two reset lines for the combphy. One for the
> > APB interface and one for the actual PHY.
> > 
> > Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> > ---
> >  .../bindings/phy/phy-rockchip-naneng-combphy.yaml          | 7 ++++++-
> >  1 file changed, 6 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > index 9ae514fa7533..bac1aae07555 100644
> > --- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
> > @@ -31,8 +31,13 @@ properties:
> >        - const: pipe
> >  
> >    resets:
> > +    minItems: 1
> > +    maxItems: 2
> > +
> > +  reset-names:
> >      items:
> > -      - description: exclusive PHY reset line
> > +      - const: phy
> > +      - const: apb
> 
> This will fail on any existing users with single entry. You need to add 
> 'minItems: 1' here.
> 
> It also fails if they didn't use 'phy' as the name, but names should be 
> defined.

My understanding is, there there currently are users with one entry
and no reset-names. I suppose its sensible not to provide a
reset-name, iff there is only one line. As far as I can tell that
should still work after my changes.

-- Sebastian

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

[-- Attachment #2: Type: text/plain, Size: 170 bytes --]

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Serge Semin]

Hi Sebastian

On Thu, Apr 13, 2023 at 08:23:42PM +0200, Sebastian Reichel wrote:
> Just like RK3568, the RK3588 has a DWC based AHCI controller.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
> details unfortunately. It is required for functional SATA, though.
> ---
>  .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
>  Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
>  2 files changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> index c1457910520b..0df8f49431eb 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> @@ -31,11 +31,11 @@ properties:
>        PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
>        clock, etc.
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>  
>    clock-names:
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>      items:
>        oneOf:
>          - description: Application APB/AHB/AXI BIU clock
> @@ -50,6 +50,8 @@ properties:
>            const: rxoob
>          - description: SATA Ports reference clock
>            const: ref

> +        - description: Rockchip ASIC clock
> +          const: asic

Actually it's a standard DW SATA AHCI PHY-interface clock (named as
clk_asicN in the DW SATA AHCI HW manual). So feel free to add it to the
clock-names array with the description (taken from the manual): "PHY
Transmit Clock". The manual also says that the clock is generated by
the PHY0 for clocking Port0 Link and Transport Layers (TX clock
domain): 37.5 MHz, 75 MHz, 150 MHz, 300 MHz, or 600 MHz.

Similarly there is another clocks source "clk_rbcN". It's "PHY Receive
Clock" which is used to receive data from the PHYn. It can be also
added to the clock-names property under the name "rbc".

Note 1. Please add the suggested names to the property constraint
above the "ref" name definition. The later clock is mainly relevant to
the attached PHY rather than to the SATA AHCI controller itself.

Note 2. "rxoob", "asic" and "rbc" clocks are defined as "clk_rxoobN",
"clk_asicN" and "clk_rbcN" which means they are supposed to be defined
(if relevant) for each available SATA port. So in general they should
have been defined in the port sub-nodes clocks/clock-names properties.

Note 3. Note natively DW SATA AHCI doesn't have any PIPE interface (or
anything being called as PIPE). Instead it provides a PMA-interface
which is directly connected to a Synopsys SATA xG PHY with no
intermediate coders (PCS). Like this:

+---------+     +--------+
|         | PMA | Snps DW| SATA
| DW SATA |<--->| SATA xG|<---->
|  AHCI   | I/F |  PHY   |
|         |     |        |
+---------+     +--------+

In that case the DW SATA AHCI IP-core is supposed to be synthesized
with the particular Synopsys PHY type specified in the parameter
PHY_INTERFACE_TYPE. If a non-standard PHY is connected (like in your
case) PHY_INTERFACE_TYPE is supposed to be set to zero thus providing
a wide set of the PMA-interface configs which otherwise would have
been pre-defined with the Synopsys PHY-specific values. So judging by
the clock names in your patches and the way the DT-nodes are designed
Rockchip SATA AHCI controller diagram must be looking like this:

+---------+      +-------+       +--------+
|         | PIPE | some  | Rx/Tx | PMA/PMD| SATA
| DW SATA |<---->|  PCS  |<----->| NANEng |<---->
|  AHCI   |former|       |       |  PHY   |
|         |DW PMA|       |       |        |
+---------+      +-------+       +--------+

In the former case (DW SATA AHCI with Synopsys SATA xG PHY attached)
all the clocks "pmalive", "rbc", "asic" and "rxoob" are generated by
the Synopsys PHYs itself so there is no need in having them explicitly
defined in the system. In your case AFAICS a non-standard PCS+PHY
setup is utilized and the clocks are generated by a system-wide unit -
CRU.

>  
>    resets:
>      description:
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> index 5afa4b57ce20..c6a0d6c8b62c 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> @@ -23,9 +23,11 @@ properties:
>          const: snps,dwc-ahci
>        - description: SPEAr1340 AHCI SATA device
>          const: snps,spear-ahci

> -      - description: Rockhip RK3568 AHCI controller
> +      - description: Rockhip AHCI controller
>          items:
> -          - const: rockchip,rk3568-dwc-ahci
> +          - enum:
> +              - rockchip,rk3568-dwc-ahci
> +              - rockchip,rk3588-dwc-ahci
>            - const: snps,dwc-ahci

What about moving all that in a dedicated YAML-file in order to define a
more comprehensive schema with actual "clocks", "clock-names",
ports-specific properties constraints? (see the way it's done for
Baikal-T1 SATA AHCI in ata/baikal,bt1-ahci.yaml).

Please note in that case you'll either need to drop the generic
fallback compatible (it's not like it would have been much useful
anyway) from your and RK3568 SATA DT-nodes, or define the
"select: properties: compatible: ..." property in the generic
DW SATA AHCI DT-schema, in order to prevent the generic schema being
automatically applied to the your SATA DT-nodes.

-Serge(y)

>  
>  patternProperties:
> -- 
> 2.39.2
> 

Re: [PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Serge Semin]

Hi Sebastian

On Thu, Apr 13, 2023 at 08:23:42PM +0200, Sebastian Reichel wrote:
> Just like RK3568, the RK3588 has a DWC based AHCI controller.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
> details unfortunately. It is required for functional SATA, though.
> ---
>  .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
>  Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
>  2 files changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> index c1457910520b..0df8f49431eb 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> @@ -31,11 +31,11 @@ properties:
>        PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
>        clock, etc.
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>  
>    clock-names:
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>      items:
>        oneOf:
>          - description: Application APB/AHB/AXI BIU clock
> @@ -50,6 +50,8 @@ properties:
>            const: rxoob
>          - description: SATA Ports reference clock
>            const: ref

> +        - description: Rockchip ASIC clock
> +          const: asic

Actually it's a standard DW SATA AHCI PHY-interface clock (named as
clk_asicN in the DW SATA AHCI HW manual). So feel free to add it to the
clock-names array with the description (taken from the manual): "PHY
Transmit Clock". The manual also says that the clock is generated by
the PHY0 for clocking Port0 Link and Transport Layers (TX clock
domain): 37.5 MHz, 75 MHz, 150 MHz, 300 MHz, or 600 MHz.

Similarly there is another clocks source "clk_rbcN". It's "PHY Receive
Clock" which is used to receive data from the PHYn. It can be also
added to the clock-names property under the name "rbc".

Note 1. Please add the suggested names to the property constraint
above the "ref" name definition. The later clock is mainly relevant to
the attached PHY rather than to the SATA AHCI controller itself.

Note 2. "rxoob", "asic" and "rbc" clocks are defined as "clk_rxoobN",
"clk_asicN" and "clk_rbcN" which means they are supposed to be defined
(if relevant) for each available SATA port. So in general they should
have been defined in the port sub-nodes clocks/clock-names properties.

Note 3. Note natively DW SATA AHCI doesn't have any PIPE interface (or
anything being called as PIPE). Instead it provides a PMA-interface
which is directly connected to a Synopsys SATA xG PHY with no
intermediate coders (PCS). Like this:

+---------+     +--------+
|         | PMA | Snps DW| SATA
| DW SATA |<--->| SATA xG|<---->
|  AHCI   | I/F |  PHY   |
|         |     |        |
+---------+     +--------+

In that case the DW SATA AHCI IP-core is supposed to be synthesized
with the particular Synopsys PHY type specified in the parameter
PHY_INTERFACE_TYPE. If a non-standard PHY is connected (like in your
case) PHY_INTERFACE_TYPE is supposed to be set to zero thus providing
a wide set of the PMA-interface configs which otherwise would have
been pre-defined with the Synopsys PHY-specific values. So judging by
the clock names in your patches and the way the DT-nodes are designed
Rockchip SATA AHCI controller diagram must be looking like this:

+---------+      +-------+       +--------+
|         | PIPE | some  | Rx/Tx | PMA/PMD| SATA
| DW SATA |<---->|  PCS  |<----->| NANEng |<---->
|  AHCI   |former|       |       |  PHY   |
|         |DW PMA|       |       |        |
+---------+      +-------+       +--------+

In the former case (DW SATA AHCI with Synopsys SATA xG PHY attached)
all the clocks "pmalive", "rbc", "asic" and "rxoob" are generated by
the Synopsys PHYs itself so there is no need in having them explicitly
defined in the system. In your case AFAICS a non-standard PCS+PHY
setup is utilized and the clocks are generated by a system-wide unit -
CRU.

>  
>    resets:
>      description:
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> index 5afa4b57ce20..c6a0d6c8b62c 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> @@ -23,9 +23,11 @@ properties:
>          const: snps,dwc-ahci
>        - description: SPEAr1340 AHCI SATA device
>          const: snps,spear-ahci

> -      - description: Rockhip RK3568 AHCI controller
> +      - description: Rockhip AHCI controller
>          items:
> -          - const: rockchip,rk3568-dwc-ahci
> +          - enum:
> +              - rockchip,rk3568-dwc-ahci
> +              - rockchip,rk3588-dwc-ahci
>            - const: snps,dwc-ahci

What about moving all that in a dedicated YAML-file in order to define a
more comprehensive schema with actual "clocks", "clock-names",
ports-specific properties constraints? (see the way it's done for
Baikal-T1 SATA AHCI in ata/baikal,bt1-ahci.yaml).

Please note in that case you'll either need to drop the generic
fallback compatible (it's not like it would have been much useful
anyway) from your and RK3568 SATA DT-nodes, or define the
"select: properties: compatible: ..." property in the generic
DW SATA AHCI DT-schema, in order to prevent the generic schema being
automatically applied to the your SATA DT-nodes.

-Serge(y)

>  
>  patternProperties:
> -- 
> 2.39.2
> 

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCHv1 2/5] dt-bindings: ata: ahci: add RK3588 AHCI controller

[Serge Semin]

Hi Sebastian

On Thu, Apr 13, 2023 at 08:23:42PM +0200, Sebastian Reichel wrote:
> Just like RK3568, the RK3588 has a DWC based AHCI controller.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> FWIW IDK what exactly the ASIC clock is. The TRM does not provide any
> details unfortunately. It is required for functional SATA, though.
> ---
>  .../devicetree/bindings/ata/snps,dwc-ahci-common.yaml       | 6 ++++--
>  Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml    | 6 ++++--
>  2 files changed, 8 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> index c1457910520b..0df8f49431eb 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci-common.yaml
> @@ -31,11 +31,11 @@ properties:
>        PM-alive clock, RxOOB detection clock, embedded PHYs reference (Rx/Tx)
>        clock, etc.
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>  
>    clock-names:
>      minItems: 1
> -    maxItems: 4
> +    maxItems: 5
>      items:
>        oneOf:
>          - description: Application APB/AHB/AXI BIU clock
> @@ -50,6 +50,8 @@ properties:
>            const: rxoob
>          - description: SATA Ports reference clock
>            const: ref

> +        - description: Rockchip ASIC clock
> +          const: asic

Actually it's a standard DW SATA AHCI PHY-interface clock (named as
clk_asicN in the DW SATA AHCI HW manual). So feel free to add it to the
clock-names array with the description (taken from the manual): "PHY
Transmit Clock". The manual also says that the clock is generated by
the PHY0 for clocking Port0 Link and Transport Layers (TX clock
domain): 37.5 MHz, 75 MHz, 150 MHz, 300 MHz, or 600 MHz.

Similarly there is another clocks source "clk_rbcN". It's "PHY Receive
Clock" which is used to receive data from the PHYn. It can be also
added to the clock-names property under the name "rbc".

Note 1. Please add the suggested names to the property constraint
above the "ref" name definition. The later clock is mainly relevant to
the attached PHY rather than to the SATA AHCI controller itself.

Note 2. "rxoob", "asic" and "rbc" clocks are defined as "clk_rxoobN",
"clk_asicN" and "clk_rbcN" which means they are supposed to be defined
(if relevant) for each available SATA port. So in general they should
have been defined in the port sub-nodes clocks/clock-names properties.

Note 3. Note natively DW SATA AHCI doesn't have any PIPE interface (or
anything being called as PIPE). Instead it provides a PMA-interface
which is directly connected to a Synopsys SATA xG PHY with no
intermediate coders (PCS). Like this:

+---------+     +--------+
|         | PMA | Snps DW| SATA
| DW SATA |<--->| SATA xG|<---->
|  AHCI   | I/F |  PHY   |
|         |     |        |
+---------+     +--------+

In that case the DW SATA AHCI IP-core is supposed to be synthesized
with the particular Synopsys PHY type specified in the parameter
PHY_INTERFACE_TYPE. If a non-standard PHY is connected (like in your
case) PHY_INTERFACE_TYPE is supposed to be set to zero thus providing
a wide set of the PMA-interface configs which otherwise would have
been pre-defined with the Synopsys PHY-specific values. So judging by
the clock names in your patches and the way the DT-nodes are designed
Rockchip SATA AHCI controller diagram must be looking like this:

+---------+      +-------+       +--------+
|         | PIPE | some  | Rx/Tx | PMA/PMD| SATA
| DW SATA |<---->|  PCS  |<----->| NANEng |<---->
|  AHCI   |former|       |       |  PHY   |
|         |DW PMA|       |       |        |
+---------+      +-------+       +--------+

In the former case (DW SATA AHCI with Synopsys SATA xG PHY attached)
all the clocks "pmalive", "rbc", "asic" and "rxoob" are generated by
the Synopsys PHYs itself so there is no need in having them explicitly
defined in the system. In your case AFAICS a non-standard PCS+PHY
setup is utilized and the clocks are generated by a system-wide unit -
CRU.

>  
>    resets:
>      description:
> diff --git a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> index 5afa4b57ce20..c6a0d6c8b62c 100644
> --- a/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> +++ b/Documentation/devicetree/bindings/ata/snps,dwc-ahci.yaml
> @@ -23,9 +23,11 @@ properties:
>          const: snps,dwc-ahci
>        - description: SPEAr1340 AHCI SATA device
>          const: snps,spear-ahci

> -      - description: Rockhip RK3568 AHCI controller
> +      - description: Rockhip AHCI controller
>          items:
> -          - const: rockchip,rk3568-dwc-ahci
> +          - enum:
> +              - rockchip,rk3568-dwc-ahci
> +              - rockchip,rk3588-dwc-ahci
>            - const: snps,dwc-ahci

What about moving all that in a dedicated YAML-file in order to define a
more comprehensive schema with actual "clocks", "clock-names",
ports-specific properties constraints? (see the way it's done for
Baikal-T1 SATA AHCI in ata/baikal,bt1-ahci.yaml).

Please note in that case you'll either need to drop the generic
fallback compatible (it's not like it would have been much useful
anyway) from your and RK3568 SATA DT-nodes, or define the
"select: properties: compatible: ..." property in the generic
DW SATA AHCI DT-schema, in order to prevent the generic schema being
automatically applied to the your SATA DT-nodes.

-Serge(y)

>  
>  patternProperties:
> -- 
> 2.39.2
> 

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy