* [PATCH V5 0/2] Fix WKUP domain IO PADCONFIG issue and add RPi header support
@ 2023-05-04 7:34 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2023-05-04 7:34 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
Hi All,
This patch series fix the incorrect IO PADCONFIG offset size of the
wakeup domain for J721S2 SoC and add RPi expansion header support
for the AM68 SK.
---
Changes in V5:
-Remove main padconfig split patch which is not required.
Changes in V4:
- Address review comments
* Update main and wakeup domain IO padconfig
* Correct the pinctrl node offsets as per the newly split wkup_pmx*
and main_pmx* nodes.
Changes in V3:
- Add Fixes tag.
Changes in V2:
- Update commit description.
- Update the offset value to 0x194 as 0x190 is the last register of the
IO PADCONFIG register set.
V1: https://lore.kernel.org/all/20230123135831.4184-1-sinthu.raja@ti.com/
V2: https://lore.kernel.org/lkml/20230124120311.7323-1-sinthu.raja@ti.com/T/
V3: https://lore.kernel.org/linux-arm-kernel/20230316114102.3602-2-sinthu.raja@ti.com/T/
V4: https://lore.kernel.org/lkml/20230424081536.12123-1-sinthu.raja@ti.com/
Sinthu Raja (2):
arm64: dts: ti: k3-j721s2: fix wkup pinmux range
arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header
.../boot/dts/ti/k3-am68-sk-base-board.dts | 119 ++++++++++++++----
.../dts/ti/k3-j721s2-common-proc-board.dts | 76 +++++------
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 29 ++++-
3 files changed, 163 insertions(+), 61 deletions(-)
--
2.36.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V5 0/2] Fix WKUP domain IO PADCONFIG issue and add RPi header support
@ 2023-05-04 7:34 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2023-05-04 7:34 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
Hi All,
This patch series fix the incorrect IO PADCONFIG offset size of the
wakeup domain for J721S2 SoC and add RPi expansion header support
for the AM68 SK.
---
Changes in V5:
-Remove main padconfig split patch which is not required.
Changes in V4:
- Address review comments
* Update main and wakeup domain IO padconfig
* Correct the pinctrl node offsets as per the newly split wkup_pmx*
and main_pmx* nodes.
Changes in V3:
- Add Fixes tag.
Changes in V2:
- Update commit description.
- Update the offset value to 0x194 as 0x190 is the last register of the
IO PADCONFIG register set.
V1: https://lore.kernel.org/all/20230123135831.4184-1-sinthu.raja@ti.com/
V2: https://lore.kernel.org/lkml/20230124120311.7323-1-sinthu.raja@ti.com/T/
V3: https://lore.kernel.org/linux-arm-kernel/20230316114102.3602-2-sinthu.raja@ti.com/T/
V4: https://lore.kernel.org/lkml/20230424081536.12123-1-sinthu.raja@ti.com/
Sinthu Raja (2):
arm64: dts: ti: k3-j721s2: fix wkup pinmux range
arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header
.../boot/dts/ti/k3-am68-sk-base-board.dts | 119 ++++++++++++++----
.../dts/ti/k3-j721s2-common-proc-board.dts | 76 +++++------
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 29 ++++-
3 files changed, 163 insertions(+), 61 deletions(-)
--
2.36.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range
2023-05-04 7:34 ` Sinthu Raja
@ 2023-05-04 7:34 ` Sinthu Raja
-1 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2023-05-04 7:34 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja, Thejasvi Konduru
From: Sinthu Raja <sinthu.raja@ti.com>
The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
regions, accordingly split the existing wkup_pmx region as follows to avoid
the non-addressable regions and include the rest of valid WKUP_PADCONFIG
registers. Also update references to old nodes with new ones.
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
Fixes: b8545f9d3a54 ("arm64: dts: ti: Add initial support for J721S2 SoC")
Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
No changes in V5.
Changes in V4:
- Correct the pinctrl node offsets as per the newly split wkup_pmx*
nodes
Changes in V3:
- Added Fix tag
Changes in V2:
- Update commit description.
- Update the offset value to 0x194 because 0x190 is the last register of the
IO PADCONFIG register set.
.../boot/dts/ti/k3-am68-sk-base-board.dts | 42 +++++-----
.../dts/ti/k3-j721s2-common-proc-board.dts | 76 +++++++++----------
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 29 ++++++-
3 files changed, 87 insertions(+), 60 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index 27a43a8ecffd..67bcf906ded1 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -175,49 +175,49 @@ J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */
};
};
-&wkup_pmx0 {
+&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
- J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
- J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
- J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
- J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
- J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
- J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
- J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
- J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
- J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
- J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
- J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
+ J721S2_WKUP_IOPAD(0x02C, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
+ J721S2_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
+ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
+ J721S2_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
+ J721S2_WKUP_IOPAD(0x00C, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
+ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
+ J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
>;
};
mcu_mdio_pins_default: mcu-mdio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
- J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
+ J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
+ J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
>;
};
mcu_mcan0_pins_default: mcu-mcan0-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
- J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
+ J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
+ J721S2_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
>;
};
mcu_mcan1_pins_default: mcu-mcan1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
- J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
+ J721S2_WKUP_IOPAD(0x06C, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
>;
};
mcu_i2c1_pins_default: mcu-i2c1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
- J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
+ J721S2_WKUP_IOPAD(0x078, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
+ J721S2_WKUP_IOPAD(0x07c, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
>;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index b4b9edfe2d12..a7caf1c3404d 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -146,81 +146,81 @@ J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
};
};
-&wkup_pmx0 {
+&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
- J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
- J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
- J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
- J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
- J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
- J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
- J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
- J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
- J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
- J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
- J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
+ J721S2_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
+ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
+ J721S2_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
+ J721S2_WKUP_IOPAD(0x00c, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
+ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
+ J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
>;
};
mcu_mdio_pins_default: mcu-mdio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
- J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
+ J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
+ J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
>;
};
mcu_mcan0_pins_default: mcu-mcan0-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
- J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
+ J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
+ J721S2_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
>;
};
mcu_mcan1_pins_default: mcu-mcan1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
- J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX */
+ J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /*(C23) WKUP_GPIO0_4.MCU_MCAN1_TX */
>;
};
mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0c0, PIN_INPUT, 7) /* (D26) WKUP_GPIO0_0 */
- J721S2_WKUP_IOPAD(0x0a8, PIN_INPUT, 7) /* (B25) MCU_SPI0_D1.WKUP_GPIO0_69 */
+ J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 7) /* (D26) WKUP_GPIO0_0 */
+ J721S2_WKUP_IOPAD(0x040, PIN_INPUT, 7) /* (B25) MCU_SPI0_D1.WKUP_GPIO0_69 */
>;
};
mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
+ J721S2_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
>;
};
mcu_adc0_pins_default: mcu-adc0-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x134, PIN_INPUT, 0) /* (L25) MCU_ADC0_AIN0 */
- J721S2_WKUP_IOPAD(0x138, PIN_INPUT, 0) /* (K25) MCU_ADC0_AIN1 */
- J721S2_WKUP_IOPAD(0x13c, PIN_INPUT, 0) /* (M24) MCU_ADC0_AIN2 */
- J721S2_WKUP_IOPAD(0x140, PIN_INPUT, 0) /* (L24) MCU_ADC0_AIN3 */
- J721S2_WKUP_IOPAD(0x144, PIN_INPUT, 0) /* (L27) MCU_ADC0_AIN4 */
- J721S2_WKUP_IOPAD(0x148, PIN_INPUT, 0) /* (K24) MCU_ADC0_AIN5 */
- J721S2_WKUP_IOPAD(0x14c, PIN_INPUT, 0) /* (M27) MCU_ADC0_AIN6 */
- J721S2_WKUP_IOPAD(0x150, PIN_INPUT, 0) /* (M26) MCU_ADC0_AIN7 */
+ J721S2_WKUP_IOPAD(0x0cc, PIN_INPUT, 0) /* (L25) MCU_ADC0_AIN0 */
+ J721S2_WKUP_IOPAD(0x0d0, PIN_INPUT, 0) /* (K25) MCU_ADC0_AIN1 */
+ J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (M24) MCU_ADC0_AIN2 */
+ J721S2_WKUP_IOPAD(0x0d8, PIN_INPUT, 0) /* (L24) MCU_ADC0_AIN3 */
+ J721S2_WKUP_IOPAD(0x0dc, PIN_INPUT, 0) /* (L27) MCU_ADC0_AIN4 */
+ J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (K24) MCU_ADC0_AIN5 */
+ J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (M27) MCU_ADC0_AIN6 */
+ J721S2_WKUP_IOPAD(0x0e8, PIN_INPUT, 0) /* (M26) MCU_ADC0_AIN7 */
>;
};
mcu_adc1_pins_default: mcu-adc1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x154, PIN_INPUT, 0) /* (P25) MCU_ADC1_AIN0 */
- J721S2_WKUP_IOPAD(0x158, PIN_INPUT, 0) /* (R25) MCU_ADC1_AIN1 */
- J721S2_WKUP_IOPAD(0x15c, PIN_INPUT, 0) /* (P28) MCU_ADC1_AIN2 */
- J721S2_WKUP_IOPAD(0x160, PIN_INPUT, 0) /* (P27) MCU_ADC1_AIN3 */
- J721S2_WKUP_IOPAD(0x164, PIN_INPUT, 0) /* (N25) MCU_ADC1_AIN4 */
- J721S2_WKUP_IOPAD(0x168, PIN_INPUT, 0) /* (P26) MCU_ADC1_AIN5 */
- J721S2_WKUP_IOPAD(0x16c, PIN_INPUT, 0) /* (N26) MCU_ADC1_AIN6 */
- J721S2_WKUP_IOPAD(0x170, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
+ J721S2_WKUP_IOPAD(0x0ec, PIN_INPUT, 0) /* (P25) MCU_ADC1_AIN0 */
+ J721S2_WKUP_IOPAD(0x0f0, PIN_INPUT, 0) /* (R25) MCU_ADC1_AIN1 */
+ J721S2_WKUP_IOPAD(0x0f4, PIN_INPUT, 0) /* (P28) MCU_ADC1_AIN2 */
+ J721S2_WKUP_IOPAD(0x0f8, PIN_INPUT, 0) /* (P27) MCU_ADC1_AIN3 */
+ J721S2_WKUP_IOPAD(0x0fc, PIN_INPUT, 0) /* (N25) MCU_ADC1_AIN4 */
+ J721S2_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (P26) MCU_ADC1_AIN5 */
+ J721S2_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (N26) MCU_ADC1_AIN6 */
+ J721S2_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
>;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index a353705a7463..fa31831e33e8 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -50,7 +50,34 @@ mcu_ram: sram@41c00000 {
wkup_pmx0: pinctrl@4301c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
- reg = <0x00 0x4301c000 0x00 0x178>;
+ reg = <0x00 0x4301c000 0x00 0x034>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
+ wkup_pmx1: pinctrl@4301c038 {
+ compatible = "pinctrl-single";
+ /* Proxy 0 addressing */
+ reg = <0x00 0x4301c038 0x00 0x02C>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
+ wkup_pmx2: pinctrl@4301c068 {
+ compatible = "pinctrl-single";
+ /* Proxy 0 addressing */
+ reg = <0x00 0x4301c068 0x00 0x120>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
+ wkup_pmx3: pinctrl@4301c190 {
+ compatible = "pinctrl-single";
+ /* Proxy 0 addressing */
+ reg = <0x00 0x4301c190 0x00 0x004>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <32>;
pinctrl-single,function-mask = <0xffffffff>;
--
2.36.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range
@ 2023-05-04 7:34 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2023-05-04 7:34 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja, Thejasvi Konduru
From: Sinthu Raja <sinthu.raja@ti.com>
The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
regions, accordingly split the existing wkup_pmx region as follows to avoid
the non-addressable regions and include the rest of valid WKUP_PADCONFIG
registers. Also update references to old nodes with new ones.
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
Fixes: b8545f9d3a54 ("arm64: dts: ti: Add initial support for J721S2 SoC")
Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
No changes in V5.
Changes in V4:
- Correct the pinctrl node offsets as per the newly split wkup_pmx*
nodes
Changes in V3:
- Added Fix tag
Changes in V2:
- Update commit description.
- Update the offset value to 0x194 because 0x190 is the last register of the
IO PADCONFIG register set.
.../boot/dts/ti/k3-am68-sk-base-board.dts | 42 +++++-----
.../dts/ti/k3-j721s2-common-proc-board.dts | 76 +++++++++----------
.../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 29 ++++++-
3 files changed, 87 insertions(+), 60 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index 27a43a8ecffd..67bcf906ded1 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -175,49 +175,49 @@ J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */
};
};
-&wkup_pmx0 {
+&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
- J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
- J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
- J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
- J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
- J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
- J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
- J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
- J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
- J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
- J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
- J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
+ J721S2_WKUP_IOPAD(0x02C, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
+ J721S2_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
+ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
+ J721S2_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
+ J721S2_WKUP_IOPAD(0x00C, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
+ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
+ J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
>;
};
mcu_mdio_pins_default: mcu-mdio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
- J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
+ J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
+ J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
>;
};
mcu_mcan0_pins_default: mcu-mcan0-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
- J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
+ J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
+ J721S2_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
>;
};
mcu_mcan1_pins_default: mcu-mcan1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
- J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
+ J721S2_WKUP_IOPAD(0x06C, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
>;
};
mcu_i2c1_pins_default: mcu-i2c1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
- J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
+ J721S2_WKUP_IOPAD(0x078, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
+ J721S2_WKUP_IOPAD(0x07c, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
>;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index b4b9edfe2d12..a7caf1c3404d 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -146,81 +146,81 @@ J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
};
};
-&wkup_pmx0 {
+&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
- J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
- J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
- J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
- J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
- J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
- J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
- J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
- J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
- J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
- J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
- J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
+ J721S2_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
+ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
+ J721S2_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
+ J721S2_WKUP_IOPAD(0x00c, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
+ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
+ J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
>;
};
mcu_mdio_pins_default: mcu-mdio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
- J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
+ J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
+ J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
>;
};
mcu_mcan0_pins_default: mcu-mcan0-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
- J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
+ J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
+ J721S2_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
>;
};
mcu_mcan1_pins_default: mcu-mcan1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
- J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX */
+ J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /*(C23) WKUP_GPIO0_4.MCU_MCAN1_TX */
>;
};
mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0c0, PIN_INPUT, 7) /* (D26) WKUP_GPIO0_0 */
- J721S2_WKUP_IOPAD(0x0a8, PIN_INPUT, 7) /* (B25) MCU_SPI0_D1.WKUP_GPIO0_69 */
+ J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 7) /* (D26) WKUP_GPIO0_0 */
+ J721S2_WKUP_IOPAD(0x040, PIN_INPUT, 7) /* (B25) MCU_SPI0_D1.WKUP_GPIO0_69 */
>;
};
mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
+ J721S2_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
>;
};
mcu_adc0_pins_default: mcu-adc0-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x134, PIN_INPUT, 0) /* (L25) MCU_ADC0_AIN0 */
- J721S2_WKUP_IOPAD(0x138, PIN_INPUT, 0) /* (K25) MCU_ADC0_AIN1 */
- J721S2_WKUP_IOPAD(0x13c, PIN_INPUT, 0) /* (M24) MCU_ADC0_AIN2 */
- J721S2_WKUP_IOPAD(0x140, PIN_INPUT, 0) /* (L24) MCU_ADC0_AIN3 */
- J721S2_WKUP_IOPAD(0x144, PIN_INPUT, 0) /* (L27) MCU_ADC0_AIN4 */
- J721S2_WKUP_IOPAD(0x148, PIN_INPUT, 0) /* (K24) MCU_ADC0_AIN5 */
- J721S2_WKUP_IOPAD(0x14c, PIN_INPUT, 0) /* (M27) MCU_ADC0_AIN6 */
- J721S2_WKUP_IOPAD(0x150, PIN_INPUT, 0) /* (M26) MCU_ADC0_AIN7 */
+ J721S2_WKUP_IOPAD(0x0cc, PIN_INPUT, 0) /* (L25) MCU_ADC0_AIN0 */
+ J721S2_WKUP_IOPAD(0x0d0, PIN_INPUT, 0) /* (K25) MCU_ADC0_AIN1 */
+ J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (M24) MCU_ADC0_AIN2 */
+ J721S2_WKUP_IOPAD(0x0d8, PIN_INPUT, 0) /* (L24) MCU_ADC0_AIN3 */
+ J721S2_WKUP_IOPAD(0x0dc, PIN_INPUT, 0) /* (L27) MCU_ADC0_AIN4 */
+ J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (K24) MCU_ADC0_AIN5 */
+ J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (M27) MCU_ADC0_AIN6 */
+ J721S2_WKUP_IOPAD(0x0e8, PIN_INPUT, 0) /* (M26) MCU_ADC0_AIN7 */
>;
};
mcu_adc1_pins_default: mcu-adc1-pins-default {
pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x154, PIN_INPUT, 0) /* (P25) MCU_ADC1_AIN0 */
- J721S2_WKUP_IOPAD(0x158, PIN_INPUT, 0) /* (R25) MCU_ADC1_AIN1 */
- J721S2_WKUP_IOPAD(0x15c, PIN_INPUT, 0) /* (P28) MCU_ADC1_AIN2 */
- J721S2_WKUP_IOPAD(0x160, PIN_INPUT, 0) /* (P27) MCU_ADC1_AIN3 */
- J721S2_WKUP_IOPAD(0x164, PIN_INPUT, 0) /* (N25) MCU_ADC1_AIN4 */
- J721S2_WKUP_IOPAD(0x168, PIN_INPUT, 0) /* (P26) MCU_ADC1_AIN5 */
- J721S2_WKUP_IOPAD(0x16c, PIN_INPUT, 0) /* (N26) MCU_ADC1_AIN6 */
- J721S2_WKUP_IOPAD(0x170, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
+ J721S2_WKUP_IOPAD(0x0ec, PIN_INPUT, 0) /* (P25) MCU_ADC1_AIN0 */
+ J721S2_WKUP_IOPAD(0x0f0, PIN_INPUT, 0) /* (R25) MCU_ADC1_AIN1 */
+ J721S2_WKUP_IOPAD(0x0f4, PIN_INPUT, 0) /* (P28) MCU_ADC1_AIN2 */
+ J721S2_WKUP_IOPAD(0x0f8, PIN_INPUT, 0) /* (P27) MCU_ADC1_AIN3 */
+ J721S2_WKUP_IOPAD(0x0fc, PIN_INPUT, 0) /* (N25) MCU_ADC1_AIN4 */
+ J721S2_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (P26) MCU_ADC1_AIN5 */
+ J721S2_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (N26) MCU_ADC1_AIN6 */
+ J721S2_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
>;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index a353705a7463..fa31831e33e8 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -50,7 +50,34 @@ mcu_ram: sram@41c00000 {
wkup_pmx0: pinctrl@4301c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
- reg = <0x00 0x4301c000 0x00 0x178>;
+ reg = <0x00 0x4301c000 0x00 0x034>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
+ wkup_pmx1: pinctrl@4301c038 {
+ compatible = "pinctrl-single";
+ /* Proxy 0 addressing */
+ reg = <0x00 0x4301c038 0x00 0x02C>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
+ wkup_pmx2: pinctrl@4301c068 {
+ compatible = "pinctrl-single";
+ /* Proxy 0 addressing */
+ reg = <0x00 0x4301c068 0x00 0x120>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
+ wkup_pmx3: pinctrl@4301c190 {
+ compatible = "pinctrl-single";
+ /* Proxy 0 addressing */
+ reg = <0x00 0x4301c190 0x00 0x004>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <32>;
pinctrl-single,function-mask = <0xffffffff>;
--
2.36.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V5 2/2] arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header
2023-05-04 7:34 ` Sinthu Raja
@ 2023-05-04 7:34 ` Sinthu Raja
-1 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2023-05-04 7:34 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
Add pinmux required to bring out the i2c and gpios on 40-pin RPi
expansion header on the AM68 SK board.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
No changes in V5.
Changes in V4:
* Correct the pinctrl node offsets as per the newly split wkup_pmx*
and main_pmx* nodes.
.../boot/dts/ti/k3-am68-sk-base-board.dts | 77 ++++++++++++++++++-
1 file changed, 76 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index 67bcf906ded1..67cbbfdc16b6 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -173,6 +173,32 @@ J721S2_IOPAD(0x0a0, PIN_INPUT, 0) /* (AB25) MCASP0_AXR12.MCAN7_RX */
J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */
>;
};
+
+ main_i2c4_pins_default: main-i2c4-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AF28) MCAN13_RX.I2C4_SDA */
+ J721S2_IOPAD(0x014, PIN_INPUT_PULLUP, 8) /* (AD25) MCAN14_TX.I2C4_SCL */
+ >;
+ };
+
+ rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x0a8, PIN_INPUT, 7) /* (U24) MCASP0_AXR14.GPIO0_42 */
+ J721S2_IOPAD(0x090, PIN_INPUT, 7) /* (W24) MCASP0_AXR8.GPIO0_36 */
+ J721S2_IOPAD(0x0bc, PIN_INPUT, 7) /* (V28) MCASP1_AFSX.GPIO0_47 */
+ J721S2_IOPAD(0x06c, PIN_INPUT, 7) /* (V26) MCAN1_TX.GPIO0_27 */
+ J721S2_IOPAD(0x004, PIN_INPUT, 7) /* (W25) MCAN12_TX.GPIO0_1 */
+ J721S2_IOPAD(0x008, PIN_INPUT, 7) /* (AC24) MCAN12_RX.GPIO0_2 */
+ J721S2_IOPAD(0x0b8, PIN_INPUT, 7) /* (AA24) MCASP1_ACLKX.GPIO0_46 */
+ J721S2_IOPAD(0x00c, PIN_INPUT, 7) /* (AE28) MCAN13_TX.GPIO0_3 */
+ J721S2_IOPAD(0x034, PIN_INPUT, 7) /* (AD24) PMIC_WAKE0.GPIO0_13 */
+ J721S2_IOPAD(0x0a4, PIN_INPUT, 7) /* (T23) MCASP0_AXR13.GPIO0_41 */
+ J721S2_IOPAD(0x0c0, PIN_INPUT, 7) /* (T28) MCASP1_AXR0.GPIO0_48 */
+ J721S2_IOPAD(0x0b4, PIN_INPUT, 7) /* (U25) MCASP1_AXR4.GPIO0_45 */
+ J721S2_IOPAD(0x0cc, PIN_INPUT, 7) /* (AE27) SPI0_CS0.GPIO0_51 */
+ J721S2_IOPAD(0x08c, PIN_INPUT, 7) /* (T25) MCASP0_AXR7.GPIO0_35 */
+ >;
+ };
};
&wkup_pmx2 {
@@ -214,12 +240,46 @@ J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
>;
};
+ mcu_i2c0_pins_default: mcu-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /*(H24) WKUP_GPIO0_63.MCU_I2C0_SCL*/
+ J721S2_WKUP_IOPAD(0x09C, PIN_INPUT, 0) /*(H27) WKUP_GPIO0_64.MCU_I2C0_SDA*/
+ >;
+ };
+
mcu_i2c1_pins_default: mcu-i2c1-pins-default {
pinctrl-single,pins = <
J721S2_WKUP_IOPAD(0x078, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
J721S2_WKUP_IOPAD(0x07c, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
>;
};
+
+ mcu_rpi_header_gpio0_pins0_default: mcu-rpi-header-gpio0-pins0-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x118, PIN_INPUT, 7) /* (G25) WKUP_GPIO0_66 */
+ J721S2_WKUP_IOPAD(0x05C, PIN_INPUT, 7) /* (E24) MCU_SPI1_D0.WKUP_GPIO0_1 */
+ J721S2_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (C28) MCU_SPI1_D1.WKUP_GPIO0_2 */
+ J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 7) /* (D26) MCU_SPI1_CLK.WKUP_GPIO0_0 */
+ J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 7) /* (D25) MCU_SPI1_CS2.WKUP_GPIO0_15*/
+ J721S2_WKUP_IOPAD(0x0B8, PIN_INPUT, 7) /* (G27) WKUP_GPIO0_56 */
+ J721S2_WKUP_IOPAD(0x114, PIN_INPUT, 7) /* (J26) WKUP_GPIO0_57 */
+ J721S2_WKUP_IOPAD(0x11C, PIN_INPUT, 7) /* (J27) WKUP_GPIO0_67 */
+ J721S2_WKUP_IOPAD(0x064, PIN_INPUT, 7) /* (C27) MCU_SPI1_CS0.WKUP_GPIO0_3 */
+ >;
+ };
+};
+
+&wkup_pmx3 {
+ mcu_rpi_header_gpio0_pins1_default: mcu-rpi-header-gpio0-pins1-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_INPUT, 7) /* (K26) WKUP_GPIO0_49 */
+ >;
+ };
+};
+
+&main_gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rpi_header_gpio0_pins_default>;
};
&main_gpio2 {
@@ -235,7 +295,8 @@ &main_gpio6 {
};
&wkup_gpio0 {
- status = "disabled";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_rpi_header_gpio0_pins0_default &mcu_rpi_header_gpio0_pins1_default>;
};
&wkup_gpio1 {
@@ -271,6 +332,20 @@ exp1: gpio@21 {
};
};
+&main_i2c4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c4_pins_default>;
+ clock-frequency = <400000>;
+};
+
+&mcu_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_i2c0_pins_default>;
+ clock-frequency = <400000>;
+};
+
&main_sdhci0 {
/* Unused */
status = "disabled";
--
2.36.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V5 2/2] arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header
@ 2023-05-04 7:34 ` Sinthu Raja
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja @ 2023-05-04 7:34 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Rob Herring
Cc: Vignesh Raghavendra, Krzysztof Kozlowski, linux-arm-kernel,
devicetree, linux-kernel, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
Add pinmux required to bring out the i2c and gpios on 40-pin RPi
expansion header on the AM68 SK board.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
No changes in V5.
Changes in V4:
* Correct the pinctrl node offsets as per the newly split wkup_pmx*
and main_pmx* nodes.
.../boot/dts/ti/k3-am68-sk-base-board.dts | 77 ++++++++++++++++++-
1 file changed, 76 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index 67bcf906ded1..67cbbfdc16b6 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -173,6 +173,32 @@ J721S2_IOPAD(0x0a0, PIN_INPUT, 0) /* (AB25) MCASP0_AXR12.MCAN7_RX */
J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */
>;
};
+
+ main_i2c4_pins_default: main-i2c4-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AF28) MCAN13_RX.I2C4_SDA */
+ J721S2_IOPAD(0x014, PIN_INPUT_PULLUP, 8) /* (AD25) MCAN14_TX.I2C4_SCL */
+ >;
+ };
+
+ rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x0a8, PIN_INPUT, 7) /* (U24) MCASP0_AXR14.GPIO0_42 */
+ J721S2_IOPAD(0x090, PIN_INPUT, 7) /* (W24) MCASP0_AXR8.GPIO0_36 */
+ J721S2_IOPAD(0x0bc, PIN_INPUT, 7) /* (V28) MCASP1_AFSX.GPIO0_47 */
+ J721S2_IOPAD(0x06c, PIN_INPUT, 7) /* (V26) MCAN1_TX.GPIO0_27 */
+ J721S2_IOPAD(0x004, PIN_INPUT, 7) /* (W25) MCAN12_TX.GPIO0_1 */
+ J721S2_IOPAD(0x008, PIN_INPUT, 7) /* (AC24) MCAN12_RX.GPIO0_2 */
+ J721S2_IOPAD(0x0b8, PIN_INPUT, 7) /* (AA24) MCASP1_ACLKX.GPIO0_46 */
+ J721S2_IOPAD(0x00c, PIN_INPUT, 7) /* (AE28) MCAN13_TX.GPIO0_3 */
+ J721S2_IOPAD(0x034, PIN_INPUT, 7) /* (AD24) PMIC_WAKE0.GPIO0_13 */
+ J721S2_IOPAD(0x0a4, PIN_INPUT, 7) /* (T23) MCASP0_AXR13.GPIO0_41 */
+ J721S2_IOPAD(0x0c0, PIN_INPUT, 7) /* (T28) MCASP1_AXR0.GPIO0_48 */
+ J721S2_IOPAD(0x0b4, PIN_INPUT, 7) /* (U25) MCASP1_AXR4.GPIO0_45 */
+ J721S2_IOPAD(0x0cc, PIN_INPUT, 7) /* (AE27) SPI0_CS0.GPIO0_51 */
+ J721S2_IOPAD(0x08c, PIN_INPUT, 7) /* (T25) MCASP0_AXR7.GPIO0_35 */
+ >;
+ };
};
&wkup_pmx2 {
@@ -214,12 +240,46 @@ J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
>;
};
+ mcu_i2c0_pins_default: mcu-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /*(H24) WKUP_GPIO0_63.MCU_I2C0_SCL*/
+ J721S2_WKUP_IOPAD(0x09C, PIN_INPUT, 0) /*(H27) WKUP_GPIO0_64.MCU_I2C0_SDA*/
+ >;
+ };
+
mcu_i2c1_pins_default: mcu-i2c1-pins-default {
pinctrl-single,pins = <
J721S2_WKUP_IOPAD(0x078, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
J721S2_WKUP_IOPAD(0x07c, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
>;
};
+
+ mcu_rpi_header_gpio0_pins0_default: mcu-rpi-header-gpio0-pins0-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x118, PIN_INPUT, 7) /* (G25) WKUP_GPIO0_66 */
+ J721S2_WKUP_IOPAD(0x05C, PIN_INPUT, 7) /* (E24) MCU_SPI1_D0.WKUP_GPIO0_1 */
+ J721S2_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (C28) MCU_SPI1_D1.WKUP_GPIO0_2 */
+ J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 7) /* (D26) MCU_SPI1_CLK.WKUP_GPIO0_0 */
+ J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 7) /* (D25) MCU_SPI1_CS2.WKUP_GPIO0_15*/
+ J721S2_WKUP_IOPAD(0x0B8, PIN_INPUT, 7) /* (G27) WKUP_GPIO0_56 */
+ J721S2_WKUP_IOPAD(0x114, PIN_INPUT, 7) /* (J26) WKUP_GPIO0_57 */
+ J721S2_WKUP_IOPAD(0x11C, PIN_INPUT, 7) /* (J27) WKUP_GPIO0_67 */
+ J721S2_WKUP_IOPAD(0x064, PIN_INPUT, 7) /* (C27) MCU_SPI1_CS0.WKUP_GPIO0_3 */
+ >;
+ };
+};
+
+&wkup_pmx3 {
+ mcu_rpi_header_gpio0_pins1_default: mcu-rpi-header-gpio0-pins1-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_INPUT, 7) /* (K26) WKUP_GPIO0_49 */
+ >;
+ };
+};
+
+&main_gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rpi_header_gpio0_pins_default>;
};
&main_gpio2 {
@@ -235,7 +295,8 @@ &main_gpio6 {
};
&wkup_gpio0 {
- status = "disabled";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_rpi_header_gpio0_pins0_default &mcu_rpi_header_gpio0_pins1_default>;
};
&wkup_gpio1 {
@@ -271,6 +332,20 @@ exp1: gpio@21 {
};
};
+&main_i2c4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c4_pins_default>;
+ clock-frequency = <400000>;
+};
+
+&mcu_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_i2c0_pins_default>;
+ clock-frequency = <400000>;
+};
+
&main_sdhci0 {
/* Unused */
status = "disabled";
--
2.36.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range
2023-05-04 7:34 ` Sinthu Raja
@ 2023-05-04 11:55 ` Nishanth Menon
-1 siblings, 0 replies; 10+ messages in thread
From: Nishanth Menon @ 2023-05-04 11:55 UTC (permalink / raw)
To: Sinthu Raja
Cc: Tero Kristo, Rob Herring, Vignesh Raghavendra,
Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Sinthu Raja, Thejasvi Konduru
minor comment: $subject: s/fix/Fix - Vignesh might fix it up prior to
picking up the series.. but anyways.. just making a side note.
On 13:04-20230504, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
> regions, accordingly split the existing wkup_pmx region as follows to avoid
> the non-addressable regions and include the rest of valid WKUP_PADCONFIG
> registers. Also update references to old nodes with new ones.
>
> wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
> wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
> wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
> wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
>
> Fixes: b8545f9d3a54 ("arm64: dts: ti: Add initial support for J721S2 SoC")
> Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
is this mcu only ?
Could you provide a link to the output of:
$ cat /sys/kernel/debug/pinctrl/*/pins
Before and after the fixup? gist.github.com or some similar pastebin
link to the log will suffice.
[..]
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range
@ 2023-05-04 11:55 ` Nishanth Menon
0 siblings, 0 replies; 10+ messages in thread
From: Nishanth Menon @ 2023-05-04 11:55 UTC (permalink / raw)
To: Sinthu Raja
Cc: Tero Kristo, Rob Herring, Vignesh Raghavendra,
Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Sinthu Raja, Thejasvi Konduru
minor comment: $subject: s/fix/Fix - Vignesh might fix it up prior to
picking up the series.. but anyways.. just making a side note.
On 13:04-20230504, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
> regions, accordingly split the existing wkup_pmx region as follows to avoid
> the non-addressable regions and include the rest of valid WKUP_PADCONFIG
> registers. Also update references to old nodes with new ones.
>
> wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
> wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
> wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
> wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
>
> Fixes: b8545f9d3a54 ("arm64: dts: ti: Add initial support for J721S2 SoC")
> Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
is this mcu only ?
Could you provide a link to the output of:
$ cat /sys/kernel/debug/pinctrl/*/pins
Before and after the fixup? gist.github.com or some similar pastebin
link to the log will suffice.
[..]
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range
2023-05-04 11:55 ` Nishanth Menon
@ 2023-05-05 9:24 ` Sinthu Raja M
-1 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja M @ 2023-05-05 9:24 UTC (permalink / raw)
To: Nishanth Menon
Cc: Tero Kristo, Rob Herring, Vignesh Raghavendra,
Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Sinthu Raja, Thejasvi Konduru
On Thu, May 4, 2023 at 5:25 PM Nishanth Menon <nm@ti.com> wrote:
>
> minor comment: $subject: s/fix/Fix - Vignesh might fix it up prior to
> picking up the series.. but anyways.. just making a side note.
>
> On 13:04-20230504, Sinthu Raja wrote:
> > From: Sinthu Raja <sinthu.raja@ti.com>
> >
> > The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
> > regions, accordingly split the existing wkup_pmx region as follows to avoid
> > the non-addressable regions and include the rest of valid WKUP_PADCONFIG
> > registers. Also update references to old nodes with new ones.
> >
> > wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
> > wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
> > wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
> > wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
> >
> > Fixes: b8545f9d3a54 ("arm64: dts: ti: Add initial support for J721S2 SoC")
> > Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
> > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> > ---
>
> is this mcu only ?
Yes, the change is required only for MCU.
>
> Could you provide a link to the output of:
> $ cat /sys/kernel/debug/pinctrl/*/pins
>
> Before and after the fixup? gist.github.com or some similar pastebin
> link to the log will suffice.
Link to logs:
Before Fix: https://pastebin.com/ufseNg8U
After Fix: https://pastebin.com/ABWZ5F4G
>
> [..]
>
>
> --
> Regards,
> Nishanth Menon
> Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
--
With Regards
Sinthu Raja
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range
@ 2023-05-05 9:24 ` Sinthu Raja M
0 siblings, 0 replies; 10+ messages in thread
From: Sinthu Raja M @ 2023-05-05 9:24 UTC (permalink / raw)
To: Nishanth Menon
Cc: Tero Kristo, Rob Herring, Vignesh Raghavendra,
Krzysztof Kozlowski, linux-arm-kernel, devicetree, linux-kernel,
Sinthu Raja, Thejasvi Konduru
On Thu, May 4, 2023 at 5:25 PM Nishanth Menon <nm@ti.com> wrote:
>
> minor comment: $subject: s/fix/Fix - Vignesh might fix it up prior to
> picking up the series.. but anyways.. just making a side note.
>
> On 13:04-20230504, Sinthu Raja wrote:
> > From: Sinthu Raja <sinthu.raja@ti.com>
> >
> > The WKUP_PADCONFIG register region in J721S2 has multiple non-addressable
> > regions, accordingly split the existing wkup_pmx region as follows to avoid
> > the non-addressable regions and include the rest of valid WKUP_PADCONFIG
> > registers. Also update references to old nodes with new ones.
> >
> > wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
> > wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
> > wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
> > wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
> >
> > Fixes: b8545f9d3a54 ("arm64: dts: ti: Add initial support for J721S2 SoC")
> > Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
> > Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> > ---
>
> is this mcu only ?
Yes, the change is required only for MCU.
>
> Could you provide a link to the output of:
> $ cat /sys/kernel/debug/pinctrl/*/pins
>
> Before and after the fixup? gist.github.com or some similar pastebin
> link to the log will suffice.
Link to logs:
Before Fix: https://pastebin.com/ufseNg8U
After Fix: https://pastebin.com/ABWZ5F4G
>
> [..]
>
>
> --
> Regards,
> Nishanth Menon
> Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
--
With Regards
Sinthu Raja
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2023-05-05 9:26 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-05-04 7:34 [PATCH V5 0/2] Fix WKUP domain IO PADCONFIG issue and add RPi header support Sinthu Raja
2023-05-04 7:34 ` Sinthu Raja
2023-05-04 7:34 ` [PATCH V5 1/2] arm64: dts: ti: k3-j721s2: fix wkup pinmux range Sinthu Raja
2023-05-04 7:34 ` Sinthu Raja
2023-05-04 11:55 ` Nishanth Menon
2023-05-04 11:55 ` Nishanth Menon
2023-05-05 9:24 ` Sinthu Raja M
2023-05-05 9:24 ` Sinthu Raja M
2023-05-04 7:34 ` [PATCH V5 2/2] arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header Sinthu Raja
2023-05-04 7:34 ` Sinthu Raja
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.