* [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards
@ 2023-07-30 12:26 Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 1/5] board: rockchip: Add Pine64 Quartz64-A Board Jonas Karlman
` (4 more replies)
0 siblings, 5 replies; 6+ messages in thread
From: Jonas Karlman @ 2023-07-30 12:26 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich, Nicolas Frattaroli
Cc: u-boot, Jonas Karlman
This series was created in collaboration with Nicolas Frattaroli and add
support for Pine64 Quartz64 and SOQuartz boards with a RK3566 SoC.
- Pine64 Quartz64-A Board
- Pine64 Quartz64-B Board
- Pine64 SOQuartz on Model A
- Pine64 SOQuartz on Blade
- Pine64 SOQuartz on CM4-IO
Device trees have been imported from linux v6.4.
Changes in v2:
- Rebased on master
- Drop u-boot.dtsi pcie2x1 pinctrl change that caused pinmux issue in
linux when using EFI boot flow
- Collect r-b tags
This series depends on the following series:
- rockchip: rk3568: Device Tree updates v2 [1]
- rockchip: rk35xx: Fix SPI Flash alias v2 [2]
- rockchip: rk3568: Use dwc3-generic driver v4 [3]
A copy of this series with above dependencies can be found at [4].
[1] https://patchwork.ozlabs.org/project/uboot/list/?series=366223
[2] https://patchwork.ozlabs.org/project/uboot/list/?series=366228
[3] https://patchwork.ozlabs.org/project/uboot/list/?series=366235
[4] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-quartz64-v2
Jonas Karlman (5):
board: rockchip: Add Pine64 Quartz64-A Board
board: rockchip: Add Pine64 Quartz64-B Board
board: rockchip: Add Pine64 SOQuartz on Model A
board: rockchip: Add Pine64 SOQuartz on Blade
board: rockchip: Add Pine64 SOQuartz on CM4-IO
arch/arm/dts/Makefile | 5 +
arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi | 51 ++
arch/arm/dts/rk3566-quartz64-a.dts | 839 ++++++++++++++++++
arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi | 43 +
arch/arm/dts/rk3566-quartz64-b.dts | 739 +++++++++++++++
.../arm/dts/rk3566-soquartz-blade-u-boot.dtsi | 3 +
arch/arm/dts/rk3566-soquartz-blade.dts | 194 ++++
arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi | 3 +
arch/arm/dts/rk3566-soquartz-cm4.dts | 192 ++++
.../dts/rk3566-soquartz-model-a-u-boot.dtsi | 3 +
arch/arm/dts/rk3566-soquartz-model-a.dts | 232 +++++
arch/arm/dts/rk3566-soquartz-u-boot.dtsi | 26 +
arch/arm/dts/rk3566-soquartz.dtsi | 688 ++++++++++++++
arch/arm/mach-rockchip/rk3568/Kconfig | 6 +
board/pine64/quartz64_rk3566/Kconfig | 15 +
board/pine64/quartz64_rk3566/MAINTAINERS | 23 +
board/pine64/quartz64_rk3566/Makefile | 3 +
.../pine64/quartz64_rk3566/quartz64-rk3566.c | 1 +
configs/quartz64-a-rk3566_defconfig | 110 +++
configs/quartz64-b-rk3566_defconfig | 106 +++
configs/soquartz-blade-rk3566_defconfig | 90 ++
configs/soquartz-cm4-rk3566_defconfig | 90 ++
configs/soquartz-model-a-rk3566_defconfig | 90 ++
doc/board/rockchip/rockchip.rst | 5 +
include/configs/quartz64_rk3566.h | 10 +
25 files changed, 3567 insertions(+)
create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts
create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts
create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts
create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts
create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts
create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi
create mode 100644 board/pine64/quartz64_rk3566/Kconfig
create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS
create mode 100644 board/pine64/quartz64_rk3566/Makefile
create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c
create mode 100644 configs/quartz64-a-rk3566_defconfig
create mode 100644 configs/quartz64-b-rk3566_defconfig
create mode 100644 configs/soquartz-blade-rk3566_defconfig
create mode 100644 configs/soquartz-cm4-rk3566_defconfig
create mode 100644 configs/soquartz-model-a-rk3566_defconfig
create mode 100644 include/configs/quartz64_rk3566.h
--
2.41.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2 1/5] board: rockchip: Add Pine64 Quartz64-A Board
2023-07-30 12:26 [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards Jonas Karlman
@ 2023-07-30 12:26 ` Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 2/5] board: rockchip: Add Pine64 Quartz64-B Board Jonas Karlman
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Jonas Karlman @ 2023-07-30 12:26 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich, Nicolas Frattaroli,
Jonas Karlman
Cc: u-boot
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
---
v2:
- Drop u-boot.dtsi pcie2x1 pinctrl change
- Collect r-b tag
arch/arm/dts/Makefile | 1 +
arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi | 51 ++
arch/arm/dts/rk3566-quartz64-a.dts | 839 ++++++++++++++++++
arch/arm/mach-rockchip/rk3568/Kconfig | 6 +
board/pine64/quartz64_rk3566/Kconfig | 15 +
board/pine64/quartz64_rk3566/MAINTAINERS | 9 +
board/pine64/quartz64_rk3566/Makefile | 3 +
.../pine64/quartz64_rk3566/quartz64-rk3566.c | 1 +
configs/quartz64-a-rk3566_defconfig | 110 +++
doc/board/rockchip/rockchip.rst | 1 +
include/configs/quartz64_rk3566.h | 10 +
11 files changed, 1046 insertions(+)
create mode 100644 arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-quartz64-a.dts
create mode 100644 board/pine64/quartz64_rk3566/Kconfig
create mode 100644 board/pine64/quartz64_rk3566/MAINTAINERS
create mode 100644 board/pine64/quartz64_rk3566/Makefile
create mode 100644 board/pine64/quartz64_rk3566/quartz64-rk3566.c
create mode 100644 configs/quartz64-a-rk3566_defconfig
create mode 100644 include/configs/quartz64_rk3566.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index bd5887bf750e..5f1eaa1f7746 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -170,6 +170,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
dtb-$(CONFIG_ROCKCHIP_RK3568) += \
rk3566-anbernic-rgxx3.dtb \
+ rk3566-quartz64-a.dtb \
rk3566-radxa-cm3-io.dtb \
rk3568-evb.dtb \
rk3568-nanopi-r5c.dtb \
diff --git a/arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi b/arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
new file mode 100644
index 000000000000..06cc15ed21b8
--- /dev/null
+++ b/arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart2;
+ };
+};
+
+&gpio0 {
+ bootph-all;
+};
+
+&sdhci {
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&sfc {
+ bootph-pre-ram;
+ u-boot,spl-sfc-no-dma;
+
+ flash@0 {
+ bootph-pre-ram;
+ };
+};
+
+&uart2 {
+ bootph-all;
+ clock-frequency = <24000000>;
+ status = "okay";
+};
+
+/*
+ * U-Boot does not support multiple regulators using the same gpio,
+ * use vcc5v0_usb20_host to fix use of USB 2.0 port
+ */
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb20_host>;
+};
+
+&vcc3v3_sd {
+ bootph-pre-ram;
+};
+
+&vcc_sd_h {
+ bootph-all;
+};
diff --git a/arch/arm/dts/rk3566-quartz64-a.dts b/arch/arm/dts/rk3566-quartz64-a.dts
new file mode 100644
index 000000000000..25a8c781f4e7
--- /dev/null
+++ b/arch/arm/dts/rk3566-quartz64-a.dts
@@ -0,0 +1,839 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Pine64 RK3566 Quartz64-A Board";
+ compatible = "pine64,quartz64-a", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac1_clkin: external-gmac1-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac1_clkin";
+ #clock-cells = <0>;
+ };
+
+ fan: gpio_fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0
+ 4500 1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fan_en_h>;
+ #cooling-cells = <2>;
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-work {
+ label = "work-led";
+ default-state = "off";
+ gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_enable_h>;
+ retain-state-suspended;
+ };
+
+ led-diy {
+ label = "diy-led";
+ default-state = "on";
+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&diy_led_enable_h>;
+ retain-state-suspended;
+ };
+ };
+
+ rk817-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK817";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk817>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk817 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ post-power-on-delay-ms = <100>;
+ power-off-delay-us = <5000000>;
+ reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+
+ spdif_dit: spdif-dit {
+ compatible = "linux,spdif-dit";
+ #sound-dai-cells = <0>;
+ };
+
+ spdif_sound: spdif-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_dit>;
+ };
+ };
+
+ vcc12v_dcin: vcc12v_dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ /* vbus feeds the rk817 usb input.
+ * With no battery attached, also feeds vcc_bat+
+ * via ON/OFF_BAT jumper
+ */
+ vbus: vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_enable_h>;
+ regulator-name = "vcc3v3_pcie_p";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ vcc5v0_usb: vcc5v0_usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ /* all four ports are controlled by one gpio
+ * the host ports are sourced from vcc5v0_usb
+ * the otg port is sourced from vcc5v0_midu
+ */
+ vcc5v0_usb20_host: vcc5v0_usb20_host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb20_host_en>;
+ regulator-name = "vcc5v0_usb20_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+
+ vcc5v0_usb20_otg: vcc5v0_usb20_otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+ regulator-name = "vcc5v0_usb20_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dcdc_boost>;
+ };
+
+ vcc3v3_sd: vcc3v3_sd {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc_sd_h>;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ /* sourced from vbus and vcc_bat+ via rk817 sw5 */
+ vcc_sys: vcc_sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ vin-supply = <&vbus>;
+ };
+
+ /* sourced from vcc_sys, sdio module operates internally at 3.3v */
+ vcc_wl: vcc_wl {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_wl";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_thermal {
+ trips {
+ cpu_hot: cpu_hot {
+ temperature = <55000>;
+ hysteresis = <2000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map1 {
+ trip = <&cpu_hot>;
+ cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_3v3>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m0_miim
+ &gmac1m0_tx_bus2
+ &gmac1m0_rx_bus2
+ &gmac1m0_rgmii_clk
+ &gmac1m0_clkinout
+ &gmac1m0_rgmii_bus>;
+ snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda_0v9>;
+ avdd-1v8-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817: pmic@20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&dcdc_boost>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_logic";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_3v3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc2v8_dvp: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc2v8_dvp";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ dcdc_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ otg_switch: OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+/* i2c3 is exposed on con40
+ * pin 3 - i2c3_sda_m0, pullup to vcc_3v3
+ * pin 5 - i2c3_scl_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "okay";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_h>;
+ reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie_p>;
+ status = "okay";
+};
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ bt_wake_l: bt-wake-l {
+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ fan {
+ fan_en_h: fan-en-h {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ work_led_enable_h: work-led-enable-h {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ diy_led_enable_h: diy-led-enable-h {
+ rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_enable_h: pcie-enable-h {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie_reset_h: pcie-reset-h {
+ rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
+ rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ vcc_sd {
+ vcc_sd_h: vcc-sd-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc1v8_dvp>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_wl>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sfc {
+ pinctrl-0 = <&fspi_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+/* spdif is exposed on con40 pin 18 */
+&spdif {
+ status = "okay";
+};
+
+/* spi1 is exposed on con40
+ * pin 11 - spi1_mosi_m1
+ * pin 13 - spi1_miso_m1
+ * pin 15 - spi1_clk_m1
+ * pin 17 - spi1_cs0_m1
+ */
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1m1_cs0 &spi1m1_pins>;
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+/* uart0 is exposed on con40
+ * pin 12 - uart0_tx
+ * pin 14 - uart0_rx
+ */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ status = "okay";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rk817 1>;
+ clock-names = "lpo";
+ host-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+ device-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+ vbat-supply = <&vcc_sys>;
+ vddio-supply = <&vcca1v8_pmu>;
+ max-speed = <3000000>;
+ };
+};
+
+/* uart2 is exposed on con40
+ * pin 8 - uart2_tx_m0_debug
+ * pin 10 - uart2_rx_m0_debug
+ */
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* usb3 controller is muxed with sata1 */
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb20_otg>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
diff --git a/arch/arm/mach-rockchip/rk3568/Kconfig b/arch/arm/mach-rockchip/rk3568/Kconfig
index f46be3d081fe..baa51349f4be 100644
--- a/arch/arm/mach-rockchip/rk3568/Kconfig
+++ b/arch/arm/mach-rockchip/rk3568/Kconfig
@@ -22,6 +22,11 @@ config TARGET_ODROID_M1_RK3568
help
Hardkernel ODROID-M1 single board computer with a RK3568B2 SoC.
+config TARGET_QUARTZ64_RK3566
+ bool "Pine64 Quartz64"
+ help
+ Pine64 Quartz64 single board computer with a RK3566 SoC.
+
endchoice
config ROCKCHIP_BOOT_MODE_REG
@@ -39,5 +44,6 @@ config SYS_MALLOC_F_LEN
source "board/rockchip/evb_rk3568/Kconfig"
source "board/anbernic/rgxx3_rk3566/Kconfig"
source "board/hardkernel/odroid_m1/Kconfig"
+source "board/pine64/quartz64_rk3566/Kconfig"
endif
diff --git a/board/pine64/quartz64_rk3566/Kconfig b/board/pine64/quartz64_rk3566/Kconfig
new file mode 100644
index 000000000000..3de1d8f7a993
--- /dev/null
+++ b/board/pine64/quartz64_rk3566/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_QUARTZ64_RK3566
+
+config SYS_BOARD
+ default "quartz64_rk3566"
+
+config SYS_VENDOR
+ default "pine64"
+
+config SYS_CONFIG_NAME
+ default "quartz64_rk3566"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS
new file mode 100644
index 000000000000..dbc0dfbd9787
--- /dev/null
+++ b/board/pine64/quartz64_rk3566/MAINTAINERS
@@ -0,0 +1,9 @@
+QUARTZ64-RK3566
+M: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
+R: Jonas Karlman <jonas@kwiboo.se>
+S: Maintained
+F: board/pine64/quartz64_rk3566/
+F: include/configs/quartz64_rk3566.h
+F: configs/quartz64-a-rk3566_defconfig
+F: arch/arm/dts/rk3566-quartz64-a.dts
+F: arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
diff --git a/board/pine64/quartz64_rk3566/Makefile b/board/pine64/quartz64_rk3566/Makefile
new file mode 100644
index 000000000000..c24a40e724d7
--- /dev/null
+++ b/board/pine64/quartz64_rk3566/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y += quartz64-rk3566.o
diff --git a/board/pine64/quartz64_rk3566/quartz64-rk3566.c b/board/pine64/quartz64_rk3566/quartz64-rk3566.c
new file mode 100644
index 000000000000..4c027f2a7af9
--- /dev/null
+++ b/board/pine64/quartz64_rk3566/quartz64-rk3566.c
@@ -0,0 +1 @@
+// SPDX-License-Identifier: GPL-2.0+
diff --git a/configs/quartz64-a-rk3566_defconfig b/configs/quartz64-a-rk3566_defconfig
new file mode 100644
index 000000000000..d55b224feacd
--- /dev/null
+++ b/configs/quartz64-a-rk3566_defconfig
@@ -0,0 +1,110 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_SF_DEFAULT_SPEED=24000000
+CONFIG_SF_DEFAULT_MODE=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-a"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_ROCKCHIP_SPI_IMAGE=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI=y
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-a.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_POWER=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_SF_DEFAULT_BUS=4
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR_FIXED=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SFC=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
index 2a535f83fb1e..de2fcc284b22 100644
--- a/doc/board/rockchip/rockchip.rst
+++ b/doc/board/rockchip/rockchip.rst
@@ -96,6 +96,7 @@ List of mainline supported Rockchip boards:
* rk3568
- Rockchip Evb-RK3568 (evb-rk3568)
- Hardkernel ODROID-M1 (odroid-m1-rk3568)
+ - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
* rk3588
- Rockchip EVB (evb-rk3588)
diff --git a/include/configs/quartz64_rk3566.h b/include/configs/quartz64_rk3566.h
new file mode 100644
index 000000000000..dfe0fee94cdb
--- /dev/null
+++ b/include/configs/quartz64_rk3566.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __QUARTZ64_RK3566_H
+#define __QUARTZ64_RK3566_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+
+#include <configs/rk3568_common.h>
+
+#endif
--
2.41.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 2/5] board: rockchip: Add Pine64 Quartz64-B Board
2023-07-30 12:26 [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 1/5] board: rockchip: Add Pine64 Quartz64-A Board Jonas Karlman
@ 2023-07-30 12:26 ` Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 3/5] board: rockchip: Add Pine64 SOQuartz on Model A Jonas Karlman
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Jonas Karlman @ 2023-07-30 12:26 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich, Nicolas Frattaroli,
Jonas Karlman
Cc: u-boot
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
---
v2:
- Drop u-boot.dtsi pcie2x1 pinctrl change
- Collect r-b tag
arch/arm/dts/Makefile | 1 +
arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi | 43 ++
arch/arm/dts/rk3566-quartz64-b.dts | 739 +++++++++++++++++++++
board/pine64/quartz64_rk3566/MAINTAINERS | 3 +
configs/quartz64-b-rk3566_defconfig | 106 +++
doc/board/rockchip/rockchip.rst | 1 +
6 files changed, 893 insertions(+)
create mode 100644 arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-quartz64-b.dts
create mode 100644 configs/quartz64-b-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5f1eaa1f7746..01d0cb85ead6 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -171,6 +171,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
dtb-$(CONFIG_ROCKCHIP_RK3568) += \
rk3566-anbernic-rgxx3.dtb \
rk3566-quartz64-a.dtb \
+ rk3566-quartz64-b.dtb \
rk3566-radxa-cm3-io.dtb \
rk3568-evb.dtb \
rk3568-nanopi-r5c.dtb \
diff --git a/arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi b/arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
new file mode 100644
index 000000000000..3c2c54e94183
--- /dev/null
+++ b/arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart2;
+ };
+};
+
+&sdhci {
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&sfc {
+ bootph-pre-ram;
+ u-boot,spl-sfc-no-dma;
+
+ flash@0 {
+ bootph-pre-ram;
+ };
+};
+
+&uart2 {
+ bootph-all;
+ clock-frequency = <24000000>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+};
+
+&vcc5v0_usb30_host {
+ /delete-property/ regulator-always-on;
+};
+
+&vcc5v0_usb_otg {
+ /delete-property/ regulator-always-on;
+};
diff --git a/arch/arm/dts/rk3566-quartz64-b.dts b/arch/arm/dts/rk3566-quartz64-b.dts
new file mode 100644
index 000000000000..b276eb0810c7
--- /dev/null
+++ b/arch/arm/dts/rk3566-quartz64-b.dts
@@ -0,0 +1,739 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Pine64 RK3566 Quartz64-B Board";
+ compatible = "pine64,quartz64-b", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ mmc2 = &sdmmc1;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac1_clkin: external-gmac1-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac1_clkin";
+ #clock-cells = <0>;
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-user {
+ label = "user-led";
+ default-state = "on";
+ gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_led_enable_h>;
+ retain-state-suspended;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ status = "okay";
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <100>;
+ power-off-delay-us = <5000000>;
+ };
+
+ vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_enable_h>;
+ regulator-name = "vcc3v3_pcie_p";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ vcc5v0_in: vcc5v0-in-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_in";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_in>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb30_host";
+ enable-active-high;
+ gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb30_host_en_h>;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb_otg";
+ enable-active-high;
+ gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_usb_otg_en_h>;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+ clock_in_out = "input";
+ phy-mode = "rgmii";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_clkinout
+ &gmac1m1_rgmii_bus>;
+ snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+ snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x4f>;
+ rx_delay = <0x24>;
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ wakeup-source;
+ #clock-cells = <1>;
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-boot-on;
+ regulator-name = "vcc_3v3";
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ };
+ };
+ };
+};
+
+/* i2c2_m1 exposed on csi port, pulled up to vcc_3v3 */
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2m1_xfer>;
+ status = "okay";
+};
+
+/* i2c3_m1 exposed on dsi port, pulled up to vcc_3v3 */
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3m1_xfer>;
+ status = "okay";
+};
+
+/*
+ * i2c4_m0 is exposed on PI40, pulled up to vcc_3v3
+ * pin 27 - i2c4_sda_m0
+ * pin 28 - i2c4_scl_m0
+ */
+&i2c4 {
+ status = "okay";
+};
+
+/*
+ * i2c5_m0 is exposed on PI40
+ * pin 29 - i2c5_scl_m0
+ * pin 31 - i2c5_sda_m0
+ */
+&i2c5 {
+ status = "disabled";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x1>;
+ };
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_h>;
+ reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie_p>;
+ status = "okay";
+};
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ bt_wake_l: bt-wake-l {
+ rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ user_led_enable_h: user-led-enable-h {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_enable_h: pcie-enable-h {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pcie_reset_h: pcie-reset-h {
+ rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic_int {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ vcc5v0_usb30_host_en_h: vcc5v0-usb30-host-en_h {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_usb_otg_en_h: vcc5v0-usb-otg-en_h {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ status = "okay";
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcca1v8_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcca1v8_pmu>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_3v3>;
+ vccio7-supply = <&vcc_3v3>;
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr50;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcca1v8_pmu>;
+ status = "okay";
+};
+
+&sfc {
+ pinctrl-0 = <&fspi_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ status = "okay";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&rk809 1>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+ vbat-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcca1v8_pmu>;
+ };
+};
+
+/*
+ * uart2_m0 is exposed on PI40
+ * pin 8 - uart2_tx_m0
+ * pin 10 - uart2_rx_m0
+ */
+&uart2 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb30_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb_otg>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb30_host>;
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS
index dbc0dfbd9787..2e637bf51ba3 100644
--- a/board/pine64/quartz64_rk3566/MAINTAINERS
+++ b/board/pine64/quartz64_rk3566/MAINTAINERS
@@ -5,5 +5,8 @@ S: Maintained
F: board/pine64/quartz64_rk3566/
F: include/configs/quartz64_rk3566.h
F: configs/quartz64-a-rk3566_defconfig
+F: configs/quartz64-b-rk3566_defconfig
F: arch/arm/dts/rk3566-quartz64-a.dts
F: arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
+F: arch/arm/dts/rk3566-quartz64-b.dts
+F: arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
diff --git a/configs/quartz64-b-rk3566_defconfig b/configs/quartz64-b-rk3566_defconfig
new file mode 100644
index 000000000000..b98c81f9dcef
--- /dev/null
+++ b/configs/quartz64-b-rk3566_defconfig
@@ -0,0 +1,106 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_SF_DEFAULT_SPEED=24000000
+CONFIG_SF_DEFAULT_MODE=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-quartz64-b"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_ROCKCHIP_SPI_IMAGE=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI=y
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-quartz64-b.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_SF_DEFAULT_BUS=4
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SFC=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
index de2fcc284b22..c1c2b440040c 100644
--- a/doc/board/rockchip/rockchip.rst
+++ b/doc/board/rockchip/rockchip.rst
@@ -97,6 +97,7 @@ List of mainline supported Rockchip boards:
- Rockchip Evb-RK3568 (evb-rk3568)
- Hardkernel ODROID-M1 (odroid-m1-rk3568)
- Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
+ - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
* rk3588
- Rockchip EVB (evb-rk3588)
--
2.41.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 3/5] board: rockchip: Add Pine64 SOQuartz on Model A
2023-07-30 12:26 [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 1/5] board: rockchip: Add Pine64 Quartz64-A Board Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 2/5] board: rockchip: Add Pine64 Quartz64-B Board Jonas Karlman
@ 2023-07-30 12:26 ` Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 4/5] board: rockchip: Add Pine64 SOQuartz on Blade Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 5/5] board: rockchip: Add Pine64 SOQuartz on CM4-IO Jonas Karlman
4 siblings, 0 replies; 6+ messages in thread
From: Jonas Karlman @ 2023-07-30 12:26 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich, Nicolas Frattaroli,
Jonas Karlman
Cc: u-boot
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
---
v2:
- Drop u-boot.dtsi pcie2x1 pinctrl change
- Collect r-b tag
arch/arm/dts/Makefile | 1 +
.../dts/rk3566-soquartz-model-a-u-boot.dtsi | 3 +
arch/arm/dts/rk3566-soquartz-model-a.dts | 232 ++++++
arch/arm/dts/rk3566-soquartz-u-boot.dtsi | 26 +
arch/arm/dts/rk3566-soquartz.dtsi | 688 ++++++++++++++++++
board/pine64/quartz64_rk3566/MAINTAINERS | 5 +
configs/soquartz-model-a-rk3566_defconfig | 90 +++
doc/board/rockchip/rockchip.rst | 1 +
8 files changed, 1046 insertions(+)
create mode 100644 arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz-model-a.dts
create mode 100644 arch/arm/dts/rk3566-soquartz-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz.dtsi
create mode 100644 configs/soquartz-model-a-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 01d0cb85ead6..949615ebdbde 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -173,6 +173,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
rk3566-quartz64-a.dtb \
rk3566-quartz64-b.dtb \
rk3566-radxa-cm3-io.dtb \
+ rk3566-soquartz-model-a.dtb \
rk3568-evb.dtb \
rk3568-nanopi-r5c.dtb \
rk3568-nanopi-r5s.dtb \
diff --git a/arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi b/arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
new file mode 100644
index 000000000000..0e662eafa4c7
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
diff --git a/arch/arm/dts/rk3566-soquartz-model-a.dts b/arch/arm/dts/rk3566-soquartz-model-a.dts
new file mode 100644
index 000000000000..2208dbfb7f0a
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-model-a.dts
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+ model = "PINE64 RK3566 SOQuartz on Model A carrier board";
+ compatible = "pine64,soquartz-model-a", "pine64,soquartz", "rockchip,rk3566";
+
+ /* labeled DCIN_12V in schematic */
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc5v0_usb: vcc5v0-usb-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ /*
+ * Labelled VCC3V0_SD in schematic to not conflict with PMIC
+ * regulator, it's 3.3v in actuality
+ */
+ vcc3v0_sd: vcc3v0-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v0_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc3v3_pcie: vcc3v3-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc12v_pcie: vcc12v-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_pcie";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+/* phy for pcie */
+&combphy2 {
+ phy-supply = <&vcc3v3_sys>;
+ status = "okay";
+};
+
+&gmac1 {
+ status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "okay";
+
+ /*
+ * the rtc interrupt is tied to PMIC_PWRON,
+ * it will force reset the board if triggered.
+ */
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063";
+ reg = <0x51>;
+ };
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+ status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6 - i2s1_sdi2_m1
+ * pin 40 - GPIO9 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ status = "disabled";
+};
+
+&led_diy {
+ status = "okay";
+};
+
+&led_work {
+ status = "okay";
+};
+
+&pcie2x1 {
+ vpcie3v3-supply = <&vcc3v3_pcie>;
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+ status = "disabled";
+};
+
+/*
+ * vmmc-supply is vcc3v3_sd on v1.0 and vcc3v0_sd on v1.1+
+ * the soquartz SoM has SDMMC_PWR (CM1 pin 75) hardwired to vcc3v3_sys,
+ * so we use vcc3v3_sd here to ensure the regulator is enabled on older boards.
+ */
+&sdmmc0 {
+ vmmc-supply = <&vcc3v3_sd>;
+ status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7 - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8 - spi3_cs0_m0
+ * pin 40 - GPIO9 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+ status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&vbus {
+ vin-supply = <&vcc5v0_usb>;
+};
+
+&vcc3v3_sd {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/rk3566-soquartz-u-boot.dtsi b/arch/arm/dts/rk3566-soquartz-u-boot.dtsi
new file mode 100644
index 000000000000..793cca2ceaca
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-u-boot.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart2;
+ };
+};
+
+&sdhci {
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+};
+
+&uart2 {
+ bootph-all;
+ clock-frequency = <24000000>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+};
diff --git a/arch/arm/dts/rk3566-soquartz.dtsi b/arch/arm/dts/rk3566-soquartz.dtsi
new file mode 100644
index 000000000000..31aa2b8efe39
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz.dtsi
@@ -0,0 +1,688 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Pine64 RK3566 SoQuartz SOM";
+ compatible = "pine64,soquartz", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ mmc2 = &sdmmc1;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac1_clkin: external-gmac1-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac1_clkin";
+ #clock-cells = <0>;
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_diy: led-diy {
+ label = "diy-led";
+ default-state = "on";
+ gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&diy_led_enable_h>;
+ retain-state-suspended;
+ status = "disabled";
+ };
+
+ led_work: led-work {
+ label = "work-led";
+ default-state = "off";
+ gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_enable_h>;
+ retain-state-suspended;
+ status = "disabled";
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ status = "okay";
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+
+ vbus: vbus-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ /* sourced from vbus, vbus is provided by the carrier board */
+ vcc5v0_sys: vcc5v0-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vbus>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_3v3>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m0_miim
+ &gmac1m0_tx_bus2
+ &gmac1m0_rx_bus2
+ &gmac1m0_rgmii_clk
+ &gmac1m0_clkinout
+ &gmac1m0_rgmii_bus>;
+ snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+ snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ phy-handle = <&rgmii_phy1>;
+ status = "disabled";
+};
+
+&gpio0 {
+ nextrst-hog {
+ gpio-hog;
+ /*
+ * GPIO_ACTIVE_LOW + output-low here means that the pin is set
+ * to high, because output-low decides the value pre-inversion.
+ */
+ gpios = <RK_PA5 GPIO_ACTIVE_LOW>;
+ line-name = "nEXTRST";
+ output-low;
+ };
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_npu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_image";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_image";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ status = "disabled";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ };
+ };
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "disabled";
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A
+ * pin 56 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2m1_xfer>;
+ status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A
+ * pin 35 - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B
+ * pin 45 - i2c4_scl_m1
+ * pin 47 - i2c4_sda_m1
+ */
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4m1_xfer>;
+ status = "disabled";
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A
+ * pin 24 - i2s1_sdi1_m1
+ * pin 25 - i2s1_sdo0_m1
+ * pin 26 - i2s1_lrck_tx_m1
+ * pin 27 - i2s1_sdi0_m1
+ * pin 29 - i2s1_sdi3_m1
+ * pin 30 - i2s1_sdi2_m1
+ * pin 40 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - i2s1_sdo2_m1
+ * pin 49 - i2s1_sclk_tx_m1
+ * pin 50 - i2s1_mclk_m1
+ * pin 56 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m1_sclktx &i2s1m1_sclkrx
+ &i2s1m1_lrcktx &i2s1m1_lrckrx
+ &i2s1m1_sdi0 &i2s1m1_sdi1
+ &i2s1m1_sdi2 &i2s1m1_sdi3
+ &i2s1m1_sdo0 &i2s1m1_sdo1
+ &i2s1m1_sdo2 &i2s1m1_sdo3>;
+ status = "disabled";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ status = "disabled";
+ };
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_h>;
+ reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+};
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ bt_wake_l: bt-wake-l {
+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ work_led_enable_h: work-led-enable-h {
+ rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ diy_led_enable_h: diy-led-enable-h {
+ rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_clkreq_h: pcie-clkreq-h {
+ rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ pcie_reset_h: pcie-reset-h {
+ rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vcc_3v3>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_3v3>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A
+ * pin 94 - saradc_vin3
+ * pin 96 - saradc_vin2
+ */
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "disabled";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ broken-cd;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "disabled";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+ sd-uhs-sdr50;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A
+ * pin 37 - spi3_cs1_m0
+ * pin 38 - spi3_clk_m0
+ * pin 39 - spi3_cs0_m0
+ * pin 40 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rk809 1>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+ vbat-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcca1v8_pmu>;
+ };
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A
+ * pin 51 - uart2_rx_m0
+ * pin 55 - uart2_tx_m0
+ */
+&uart2 {
+ status = "disabled";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A
+ * pin 46 - uart7_tx_m2
+ * pin 47 - uart7_rx_m2
+ */
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7m2_xfer>;
+ status = "disabled";
+};
+
+/* dwc3_otg is the only usb port available */
+&usb2phy0 {
+ status = "disabled";
+};
+
+&usb2phy0_otg {
+ status = "disabled";
+};
+
+&usb_host0_xhci {
+ status = "disabled";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS
index 2e637bf51ba3..748ff5033d93 100644
--- a/board/pine64/quartz64_rk3566/MAINTAINERS
+++ b/board/pine64/quartz64_rk3566/MAINTAINERS
@@ -6,7 +6,12 @@ F: board/pine64/quartz64_rk3566/
F: include/configs/quartz64_rk3566.h
F: configs/quartz64-a-rk3566_defconfig
F: configs/quartz64-b-rk3566_defconfig
+F: configs/soquartz-model-a-rk3566_defconfig
F: arch/arm/dts/rk3566-quartz64-a.dts
F: arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
F: arch/arm/dts/rk3566-quartz64-b.dts
F: arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
+F: arch/arm/dts/rk3566-soquartz.dtsi
+F: arch/arm/dts/rk3566-soquartz-u-boot.dtsi
+F: arch/arm/dts/rk3566-soquartz-model-a.dts
+F: arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
diff --git a/configs/soquartz-model-a-rk3566_defconfig b/configs/soquartz-model-a-rk3566_defconfig
new file mode 100644
index 000000000000..c3958579db73
--- /dev/null
+++ b/configs/soquartz-model-a-rk3566_defconfig
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-model-a"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-model-a.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
index c1c2b440040c..5b5392aa34fa 100644
--- a/doc/board/rockchip/rockchip.rst
+++ b/doc/board/rockchip/rockchip.rst
@@ -98,6 +98,7 @@ List of mainline supported Rockchip boards:
- Hardkernel ODROID-M1 (odroid-m1-rk3568)
- Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
- Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
+ - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
* rk3588
- Rockchip EVB (evb-rk3588)
--
2.41.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 4/5] board: rockchip: Add Pine64 SOQuartz on Blade
2023-07-30 12:26 [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards Jonas Karlman
` (2 preceding siblings ...)
2023-07-30 12:26 ` [PATCH v2 3/5] board: rockchip: Add Pine64 SOQuartz on Model A Jonas Karlman
@ 2023-07-30 12:26 ` Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 5/5] board: rockchip: Add Pine64 SOQuartz on CM4-IO Jonas Karlman
4 siblings, 0 replies; 6+ messages in thread
From: Jonas Karlman @ 2023-07-30 12:26 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich, Nicolas Frattaroli,
Jonas Karlman
Cc: u-boot
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
---
v2:
- Collect r-b tag
arch/arm/dts/Makefile | 1 +
.../arm/dts/rk3566-soquartz-blade-u-boot.dtsi | 3 +
arch/arm/dts/rk3566-soquartz-blade.dts | 194 ++++++++++++++++++
board/pine64/quartz64_rk3566/MAINTAINERS | 3 +
configs/soquartz-blade-rk3566_defconfig | 90 ++++++++
doc/board/rockchip/rockchip.rst | 1 +
6 files changed, 292 insertions(+)
create mode 100644 arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz-blade.dts
create mode 100644 configs/soquartz-blade-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 949615ebdbde..5e4b3c8093f5 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -173,6 +173,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
rk3566-quartz64-a.dtb \
rk3566-quartz64-b.dtb \
rk3566-radxa-cm3-io.dtb \
+ rk3566-soquartz-blade.dtb \
rk3566-soquartz-model-a.dtb \
rk3568-evb.dtb \
rk3568-nanopi-r5c.dtb \
diff --git a/arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi b/arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
new file mode 100644
index 000000000000..0e662eafa4c7
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
diff --git a/arch/arm/dts/rk3566-soquartz-blade.dts b/arch/arm/dts/rk3566-soquartz-blade.dts
new file mode 100644
index 000000000000..4e49bebf548b
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-blade.dts
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+ model = "PINE64 RK3566 SOQuartz on Blade carrier board";
+ compatible = "pine64,soquartz-blade", "pine64,soquartz", "rockchip,rk3566";
+
+ /* labeled VCC3V0_SD in schematic to not conflict with PMIC regulator */
+ vcc3v0_sd: vcc3v0-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v0_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* labeled VCC_SSD in schematic */
+ vcc3v3_pcie_p: vcc3v3-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie_p";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vbus>;
+ };
+
+ vcc5v_dcin: vcc5v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&combphy2 {
+ phy-supply = <&vcc3v3_sys>;
+ status = "okay";
+};
+
+&gmac1 {
+ status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "okay";
+
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+ status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6 - i2s1_sdi2_m1
+ * pin 40 - GPIO9 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ status = "disabled";
+};
+
+&led_diy {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_DISK_ACTIVITY;
+ linux,default-trigger = "disk-activity";
+ status = "okay";
+};
+
+&led_work {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ status = "okay";
+};
+
+&pcie2x1 {
+ vpcie3v3-supply = <&vcc3v3_pcie_p>;
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+ status = "disabled";
+};
+
+&sdmmc0 {
+ vmmc-supply = <&vcc3v0_sd>;
+ status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7 - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8 - spi3_cs0_m0
+ * pin 40 - GPIO9 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+ status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vbus>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&vbus {
+ vin-supply = <&vcc5v_dcin>;
+};
diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS
index 748ff5033d93..603d2ee9d5e9 100644
--- a/board/pine64/quartz64_rk3566/MAINTAINERS
+++ b/board/pine64/quartz64_rk3566/MAINTAINERS
@@ -6,6 +6,7 @@ F: board/pine64/quartz64_rk3566/
F: include/configs/quartz64_rk3566.h
F: configs/quartz64-a-rk3566_defconfig
F: configs/quartz64-b-rk3566_defconfig
+F: configs/soquartz-blade-rk3566_defconfig
F: configs/soquartz-model-a-rk3566_defconfig
F: arch/arm/dts/rk3566-quartz64-a.dts
F: arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -13,5 +14,7 @@ F: arch/arm/dts/rk3566-quartz64-b.dts
F: arch/arm/dts/rk3566-quartz64-b-u-boot.dtsi
F: arch/arm/dts/rk3566-soquartz.dtsi
F: arch/arm/dts/rk3566-soquartz-u-boot.dtsi
+F: arch/arm/dts/rk3566-soquartz-blade.dts
+F: arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
F: arch/arm/dts/rk3566-soquartz-model-a.dts
F: arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
diff --git a/configs/soquartz-blade-rk3566_defconfig b/configs/soquartz-blade-rk3566_defconfig
new file mode 100644
index 000000000000..181c284e73e9
--- /dev/null
+++ b/configs/soquartz-blade-rk3566_defconfig
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-blade"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-blade.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
index 5b5392aa34fa..284148438f0c 100644
--- a/doc/board/rockchip/rockchip.rst
+++ b/doc/board/rockchip/rockchip.rst
@@ -98,6 +98,7 @@ List of mainline supported Rockchip boards:
- Hardkernel ODROID-M1 (odroid-m1-rk3568)
- Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
- Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
+ - Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig)
- Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
* rk3588
--
2.41.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2 5/5] board: rockchip: Add Pine64 SOQuartz on CM4-IO
2023-07-30 12:26 [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards Jonas Karlman
` (3 preceding siblings ...)
2023-07-30 12:26 ` [PATCH v2 4/5] board: rockchip: Add Pine64 SOQuartz on Blade Jonas Karlman
@ 2023-07-30 12:26 ` Jonas Karlman
4 siblings, 0 replies; 6+ messages in thread
From: Jonas Karlman @ 2023-07-30 12:26 UTC (permalink / raw)
To: Kever Yang, Simon Glass, Philipp Tomsich, Nicolas Frattaroli,
Jonas Karlman
Cc: u-boot
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
---
v2:
- Collect r-b tag
arch/arm/dts/Makefile | 1 +
arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi | 3 +
arch/arm/dts/rk3566-soquartz-cm4.dts | 192 +++++++++++++++++++
board/pine64/quartz64_rk3566/MAINTAINERS | 3 +
configs/soquartz-cm4-rk3566_defconfig | 90 +++++++++
doc/board/rockchip/rockchip.rst | 1 +
6 files changed, 290 insertions(+)
create mode 100644 arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
create mode 100644 arch/arm/dts/rk3566-soquartz-cm4.dts
create mode 100644 configs/soquartz-cm4-rk3566_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5e4b3c8093f5..bf8c568260a6 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -174,6 +174,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
rk3566-quartz64-b.dtb \
rk3566-radxa-cm3-io.dtb \
rk3566-soquartz-blade.dtb \
+ rk3566-soquartz-cm4.dtb \
rk3566-soquartz-model-a.dtb \
rk3568-evb.dtb \
rk3568-nanopi-r5c.dtb \
diff --git a/arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi b/arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
new file mode 100644
index 000000000000..0e662eafa4c7
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "rk3566-soquartz-u-boot.dtsi"
diff --git a/arch/arm/dts/rk3566-soquartz-cm4.dts b/arch/arm/dts/rk3566-soquartz-cm4.dts
new file mode 100644
index 000000000000..cddf6cd2fecb
--- /dev/null
+++ b/arch/arm/dts/rk3566-soquartz-cm4.dts
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+ model = "Pine64 RK3566 SoQuartz with CM4-IO Carrier Board";
+ compatible = "pine64,soquartz-cm4io", "pine64,soquartz", "rockchip,rk3566";
+
+ /* labeled +12v in schematic */
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ /* labeled +5v in schematic */
+ vcc_5v: vcc-5v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc_sd_pwr: vcc-sd-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sd_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+};
+
+/* phy for pcie */
+&combphy2 {
+ phy-supply = <&vcc3v3_sys>;
+ status = "okay";
+};
+
+&gmac1 {
+ status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "okay";
+
+ /*
+ * the rtc interrupt is tied to PMIC_PWRON,
+ * it will force reset the board if triggered.
+ */
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063";
+ reg = <0x51>;
+ };
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+ status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6 - i2s1_sdi2_m1
+ * pin 40 - GPIO9 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ status = "disabled";
+};
+
+&led_diy {
+ status = "okay";
+};
+
+&led_work {
+ status = "okay";
+};
+
+&pcie2x1 {
+ vpcie3v3-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+ status = "disabled";
+};
+
+&sdmmc0 {
+ vmmc-supply = <&vcc_sd_pwr>;
+ status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7 - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8 - spi3_cs0_m0
+ * pin 40 - GPIO9 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+ status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc_5v>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&vbus {
+ vin-supply = <&vcc_5v>;
+};
diff --git a/board/pine64/quartz64_rk3566/MAINTAINERS b/board/pine64/quartz64_rk3566/MAINTAINERS
index 603d2ee9d5e9..6b75b35a1243 100644
--- a/board/pine64/quartz64_rk3566/MAINTAINERS
+++ b/board/pine64/quartz64_rk3566/MAINTAINERS
@@ -7,6 +7,7 @@ F: include/configs/quartz64_rk3566.h
F: configs/quartz64-a-rk3566_defconfig
F: configs/quartz64-b-rk3566_defconfig
F: configs/soquartz-blade-rk3566_defconfig
+F: configs/soquartz-cm4-rk3566_defconfig
F: configs/soquartz-model-a-rk3566_defconfig
F: arch/arm/dts/rk3566-quartz64-a.dts
F: arch/arm/dts/rk3566-quartz64-a-u-boot.dtsi
@@ -16,5 +17,7 @@ F: arch/arm/dts/rk3566-soquartz.dtsi
F: arch/arm/dts/rk3566-soquartz-u-boot.dtsi
F: arch/arm/dts/rk3566-soquartz-blade.dts
F: arch/arm/dts/rk3566-soquartz-blade-u-boot.dtsi
+F: arch/arm/dts/rk3566-soquartz-cm4.dts
+F: arch/arm/dts/rk3566-soquartz-cm4-u-boot.dtsi
F: arch/arm/dts/rk3566-soquartz-model-a.dts
F: arch/arm/dts/rk3566-soquartz-model-a-u-boot.dtsi
diff --git a/configs/soquartz-cm4-rk3566_defconfig b/configs/soquartz-cm4-rk3566_defconfig
new file mode 100644
index 000000000000..7e290351477e
--- /dev/null
+++ b/configs/soquartz-cm4-rk3566_defconfig
@@ -0,0 +1,90 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3566-soquartz-cm4"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_TARGET_QUARTZ64_RK3566=y
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_PCI=y
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3566-soquartz-cm4.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SCSI_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_SPL_CLK=y
+CONFIG_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_NVME_PCI=y
+CONFIG_PCIE_DW_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
index 284148438f0c..e23237e453f3 100644
--- a/doc/board/rockchip/rockchip.rst
+++ b/doc/board/rockchip/rockchip.rst
@@ -99,6 +99,7 @@ List of mainline supported Rockchip boards:
- Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
- Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)
- Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig)
+ - Pine64 SOQuartz on CM4-IO (soquartz-cm4-rk3566_defconfig)
- Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig)
* rk3588
--
2.41.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
end of thread, other threads:[~2023-07-30 12:27 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-07-30 12:26 [PATCH v2 0/5] board: rockchip: Add Pine64 Quartz64 and SOQuartz boards Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 1/5] board: rockchip: Add Pine64 Quartz64-A Board Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 2/5] board: rockchip: Add Pine64 Quartz64-B Board Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 3/5] board: rockchip: Add Pine64 SOQuartz on Model A Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 4/5] board: rockchip: Add Pine64 SOQuartz on Blade Jonas Karlman
2023-07-30 12:26 ` [PATCH v2 5/5] board: rockchip: Add Pine64 SOQuartz on CM4-IO Jonas Karlman
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.