* [PATCH v6 0/1] Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-09-13 1:37 ` Mia Lin
0 siblings, 0 replies; 12+ messages in thread
From: Mia Lin @ 2023-09-13 1:37 UTC (permalink / raw)
To: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, alexandre.belloni, KWLIU, JJLIU0, KFLIN,
mylin1
Cc: openbmc, linux-rtc, linux-kernel, Mia Lin
Changes since version 6:
Move the part number parameter to struct nct3018y.
Changes since version 5:
Add global parameter to store part number.
Remove unnecessary changes for easier reading.
Changes since version 4:
Add an introduction bewteen NCT3015Y-R and NCT3018Y-R.
Restore the initial value of err in nct3018y_rtc_set_time().
Refine error messages to pinpoint the correct location.
Changes since version 3:
Remove the comparison between DT compatible and chip data.
Changes since version 2:
Add DT compatible to check the chip matches or not.
Changes since version 1:
rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
Mia Lin (1):
rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
1 file changed, 46 insertions(+), 6 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v6 0/1] Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-09-13 1:37 ` Mia Lin
0 siblings, 0 replies; 12+ messages in thread
From: Mia Lin @ 2023-09-13 1:37 UTC (permalink / raw)
To: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, alexandre.belloni, KWLIU, JJLIU0, KFLIN,
mylin1
Cc: linux-rtc, openbmc, Mia Lin, linux-kernel
Changes since version 6:
Move the part number parameter to struct nct3018y.
Changes since version 5:
Add global parameter to store part number.
Remove unnecessary changes for easier reading.
Changes since version 4:
Add an introduction bewteen NCT3015Y-R and NCT3018Y-R.
Restore the initial value of err in nct3018y_rtc_set_time().
Refine error messages to pinpoint the correct location.
Changes since version 3:
Remove the comparison between DT compatible and chip data.
Changes since version 2:
Add DT compatible to check the chip matches or not.
Changes since version 1:
rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
Mia Lin (1):
rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
1 file changed, 46 insertions(+), 6 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
2023-09-13 1:37 ` Mia Lin
@ 2023-09-13 1:37 ` Mia Lin
-1 siblings, 0 replies; 12+ messages in thread
From: Mia Lin @ 2023-09-13 1:37 UTC (permalink / raw)
To: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, alexandre.belloni, KWLIU, JJLIU0, KFLIN,
mylin1
Cc: openbmc, linux-rtc, linux-kernel, Mia Lin
The NCT3015Y-R and NCT3018Y-R use the same datasheet
but have different topologies as follows.
- Topology (Only 1st i2c can set TWO bit and HF bit)
In NCT3015Y-R,
rtc 1st i2c is connected to a host CPU
rtc 2nd i2c is connected to a BMC
In NCT3018Y-R,
rtc 1st i2c is connected to a BMC
rtc 2nd i2c is connected to a host CPU
In order to be compatible with NCT3015Y-R and NCT3018Y-R,
- In probe,
If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
Else, do nothing
- In set_time,
If part number is NCT3018Y-R && TWO bit is 0,
change TWO bit to 1, and restore TWO bit after updating time.
Signed-off-by: Mia Lin <mimi05633@gmail.com>
---
drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
1 file changed, 46 insertions(+), 6 deletions(-)
diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
index ed4e606be8e5..b006b58e15e2 100644
--- a/drivers/rtc/rtc-nct3018y.c
+++ b/drivers/rtc/rtc-nct3018y.c
@@ -23,6 +23,7 @@
#define NCT3018Y_REG_CTRL 0x0A /* timer control */
#define NCT3018Y_REG_ST 0x0B /* status */
#define NCT3018Y_REG_CLKO 0x0C /* clock out */
+#define NCT3018Y_REG_PART 0x21 /* part info */
#define NCT3018Y_BIT_AF BIT(7)
#define NCT3018Y_BIT_ST BIT(7)
@@ -37,10 +38,12 @@
#define NCT3018Y_REG_BAT_MASK 0x07
#define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
#define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
+#define NCT3018Y_REG_PART_NCT3018Y 0x02
struct nct3018y {
struct rtc_device *rtc;
struct i2c_client *client;
+ int part_num;
#ifdef CONFIG_COMMON_CLK
struct clk_hw clkout_hw;
#endif
@@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
{
struct i2c_client *client = to_i2c_client(dev);
+ struct nct3018y *nct3018y = dev_get_drvdata(dev);
unsigned char buf[4] = {0};
- int err;
+ int err, flags;
+ int restore_flags = 0;
+
+ flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
+ if (flags < 0) {
+ dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
+ return flags;
+ }
+
+ /* Check and set TWO bit */
+ if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
+ restore_flags = 1;
+ flags |= NCT3018Y_BIT_TWO;
+ err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
+ if (err < 0) {
+ dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
+ return err;
+ }
+ }
buf[0] = bin2bcd(tm->tm_sec);
err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
@@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
return -EIO;
}
+ /* Restore TWO bit */
+ if (restore_flags) {
+ if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
+ flags &= ~NCT3018Y_BIT_TWO;
+
+ err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
+ if (err < 0) {
+ dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
+ return err;
+ }
+ }
+
return err;
}
@@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
}
- flags = NCT3018Y_BIT_TWO;
- err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
- if (err < 0) {
- dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
- return err;
+ nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
+ if (nct3018y->part_num < 0) {
+ dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
+ return nct3018y->part_num;
+ } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
+ flags = NCT3018Y_BIT_HF;
+ err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
+ if (err < 0) {
+ dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
+ return err;
+ }
}
flags = 0;
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-09-13 1:37 ` Mia Lin
0 siblings, 0 replies; 12+ messages in thread
From: Mia Lin @ 2023-09-13 1:37 UTC (permalink / raw)
To: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, alexandre.belloni, KWLIU, JJLIU0, KFLIN,
mylin1
Cc: linux-rtc, openbmc, Mia Lin, linux-kernel
The NCT3015Y-R and NCT3018Y-R use the same datasheet
but have different topologies as follows.
- Topology (Only 1st i2c can set TWO bit and HF bit)
In NCT3015Y-R,
rtc 1st i2c is connected to a host CPU
rtc 2nd i2c is connected to a BMC
In NCT3018Y-R,
rtc 1st i2c is connected to a BMC
rtc 2nd i2c is connected to a host CPU
In order to be compatible with NCT3015Y-R and NCT3018Y-R,
- In probe,
If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
Else, do nothing
- In set_time,
If part number is NCT3018Y-R && TWO bit is 0,
change TWO bit to 1, and restore TWO bit after updating time.
Signed-off-by: Mia Lin <mimi05633@gmail.com>
---
drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
1 file changed, 46 insertions(+), 6 deletions(-)
diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
index ed4e606be8e5..b006b58e15e2 100644
--- a/drivers/rtc/rtc-nct3018y.c
+++ b/drivers/rtc/rtc-nct3018y.c
@@ -23,6 +23,7 @@
#define NCT3018Y_REG_CTRL 0x0A /* timer control */
#define NCT3018Y_REG_ST 0x0B /* status */
#define NCT3018Y_REG_CLKO 0x0C /* clock out */
+#define NCT3018Y_REG_PART 0x21 /* part info */
#define NCT3018Y_BIT_AF BIT(7)
#define NCT3018Y_BIT_ST BIT(7)
@@ -37,10 +38,12 @@
#define NCT3018Y_REG_BAT_MASK 0x07
#define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
#define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
+#define NCT3018Y_REG_PART_NCT3018Y 0x02
struct nct3018y {
struct rtc_device *rtc;
struct i2c_client *client;
+ int part_num;
#ifdef CONFIG_COMMON_CLK
struct clk_hw clkout_hw;
#endif
@@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
{
struct i2c_client *client = to_i2c_client(dev);
+ struct nct3018y *nct3018y = dev_get_drvdata(dev);
unsigned char buf[4] = {0};
- int err;
+ int err, flags;
+ int restore_flags = 0;
+
+ flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
+ if (flags < 0) {
+ dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
+ return flags;
+ }
+
+ /* Check and set TWO bit */
+ if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
+ restore_flags = 1;
+ flags |= NCT3018Y_BIT_TWO;
+ err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
+ if (err < 0) {
+ dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
+ return err;
+ }
+ }
buf[0] = bin2bcd(tm->tm_sec);
err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
@@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
return -EIO;
}
+ /* Restore TWO bit */
+ if (restore_flags) {
+ if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
+ flags &= ~NCT3018Y_BIT_TWO;
+
+ err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
+ if (err < 0) {
+ dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
+ return err;
+ }
+ }
+
return err;
}
@@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
}
- flags = NCT3018Y_BIT_TWO;
- err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
- if (err < 0) {
- dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
- return err;
+ nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
+ if (nct3018y->part_num < 0) {
+ dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
+ return nct3018y->part_num;
+ } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
+ flags = NCT3018Y_BIT_HF;
+ err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
+ if (err < 0) {
+ dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
+ return err;
+ }
}
flags = 0;
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
2023-09-13 1:37 ` Mia Lin
@ 2023-11-03 23:16 ` Alexandre Belloni
-1 siblings, 0 replies; 12+ messages in thread
From: Alexandre Belloni @ 2023-11-03 23:16 UTC (permalink / raw)
To: Mia Lin
Cc: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, KWLIU, JJLIU0, KFLIN, mylin1, openbmc,
linux-rtc, linux-kernel
On 13/09/2023 09:37:19+0800, Mia Lin wrote:
> The NCT3015Y-R and NCT3018Y-R use the same datasheet
> but have different topologies as follows.
> - Topology (Only 1st i2c can set TWO bit and HF bit)
> In NCT3015Y-R,
> rtc 1st i2c is connected to a host CPU
> rtc 2nd i2c is connected to a BMC
> In NCT3018Y-R,
> rtc 1st i2c is connected to a BMC
> rtc 2nd i2c is connected to a host CPU
> In order to be compatible with NCT3015Y-R and NCT3018Y-R,
> - In probe,
> If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
> Else, do nothing
> - In set_time,
> If part number is NCT3018Y-R && TWO bit is 0,
> change TWO bit to 1, and restore TWO bit after updating time.
>
> Signed-off-by: Mia Lin <mimi05633@gmail.com>
> ---
> drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
> 1 file changed, 46 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
> index ed4e606be8e5..b006b58e15e2 100644
> --- a/drivers/rtc/rtc-nct3018y.c
> +++ b/drivers/rtc/rtc-nct3018y.c
> @@ -23,6 +23,7 @@
> #define NCT3018Y_REG_CTRL 0x0A /* timer control */
> #define NCT3018Y_REG_ST 0x0B /* status */
> #define NCT3018Y_REG_CLKO 0x0C /* clock out */
> +#define NCT3018Y_REG_PART 0x21 /* part info */
>
> #define NCT3018Y_BIT_AF BIT(7)
> #define NCT3018Y_BIT_ST BIT(7)
> @@ -37,10 +38,12 @@
> #define NCT3018Y_REG_BAT_MASK 0x07
> #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
> #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
> +#define NCT3018Y_REG_PART_NCT3018Y 0x02
>
> struct nct3018y {
> struct rtc_device *rtc;
> struct i2c_client *client;
> + int part_num;
> #ifdef CONFIG_COMMON_CLK
> struct clk_hw clkout_hw;
> #endif
> @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
> static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> {
> struct i2c_client *client = to_i2c_client(dev);
> + struct nct3018y *nct3018y = dev_get_drvdata(dev);
> unsigned char buf[4] = {0};
> - int err;
> + int err, flags;
> + int restore_flags = 0;
> +
> + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
> + if (flags < 0) {
> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
> + return flags;
> + }
> +
> + /* Check and set TWO bit */
> + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
> + restore_flags = 1;
> + flags |= NCT3018Y_BIT_TWO;
> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> + if (err < 0) {
> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> + return err;
> + }
> + }
>
> buf[0] = bin2bcd(tm->tm_sec);
> err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
> @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> return -EIO;
> }
>
> + /* Restore TWO bit */
> + if (restore_flags) {
> + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
> + flags &= ~NCT3018Y_BIT_TWO;
> +
> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> + if (err < 0) {
> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> + return err;
> + }
> + }
> +
> return err;
> }
>
> @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
> dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
> }
>
> - flags = NCT3018Y_BIT_TWO;
> - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> - if (err < 0) {
> - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
> - return err;
> + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
> + if (nct3018y->part_num < 0) {
> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
> + return nct3018y->part_num;
> + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
This is a weird way to check as this will accept any value of
NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
> + flags = NCT3018Y_BIT_HF;
> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> + if (err < 0) {
> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> + return err;
> + }
> }
>
> flags = 0;
> --
> 2.17.1
>
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-11-03 23:16 ` Alexandre Belloni
0 siblings, 0 replies; 12+ messages in thread
From: Alexandre Belloni @ 2023-11-03 23:16 UTC (permalink / raw)
To: Mia Lin
Cc: linux-rtc, a.zummo, mylin1, benjaminfair, KWLIU, avifishman70,
venture, openbmc, JJLIU0, linux-kernel, tali.perry1, KFLIN,
tmaimon77
On 13/09/2023 09:37:19+0800, Mia Lin wrote:
> The NCT3015Y-R and NCT3018Y-R use the same datasheet
> but have different topologies as follows.
> - Topology (Only 1st i2c can set TWO bit and HF bit)
> In NCT3015Y-R,
> rtc 1st i2c is connected to a host CPU
> rtc 2nd i2c is connected to a BMC
> In NCT3018Y-R,
> rtc 1st i2c is connected to a BMC
> rtc 2nd i2c is connected to a host CPU
> In order to be compatible with NCT3015Y-R and NCT3018Y-R,
> - In probe,
> If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
> Else, do nothing
> - In set_time,
> If part number is NCT3018Y-R && TWO bit is 0,
> change TWO bit to 1, and restore TWO bit after updating time.
>
> Signed-off-by: Mia Lin <mimi05633@gmail.com>
> ---
> drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
> 1 file changed, 46 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
> index ed4e606be8e5..b006b58e15e2 100644
> --- a/drivers/rtc/rtc-nct3018y.c
> +++ b/drivers/rtc/rtc-nct3018y.c
> @@ -23,6 +23,7 @@
> #define NCT3018Y_REG_CTRL 0x0A /* timer control */
> #define NCT3018Y_REG_ST 0x0B /* status */
> #define NCT3018Y_REG_CLKO 0x0C /* clock out */
> +#define NCT3018Y_REG_PART 0x21 /* part info */
>
> #define NCT3018Y_BIT_AF BIT(7)
> #define NCT3018Y_BIT_ST BIT(7)
> @@ -37,10 +38,12 @@
> #define NCT3018Y_REG_BAT_MASK 0x07
> #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
> #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
> +#define NCT3018Y_REG_PART_NCT3018Y 0x02
>
> struct nct3018y {
> struct rtc_device *rtc;
> struct i2c_client *client;
> + int part_num;
> #ifdef CONFIG_COMMON_CLK
> struct clk_hw clkout_hw;
> #endif
> @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
> static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> {
> struct i2c_client *client = to_i2c_client(dev);
> + struct nct3018y *nct3018y = dev_get_drvdata(dev);
> unsigned char buf[4] = {0};
> - int err;
> + int err, flags;
> + int restore_flags = 0;
> +
> + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
> + if (flags < 0) {
> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
> + return flags;
> + }
> +
> + /* Check and set TWO bit */
> + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
> + restore_flags = 1;
> + flags |= NCT3018Y_BIT_TWO;
> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> + if (err < 0) {
> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> + return err;
> + }
> + }
>
> buf[0] = bin2bcd(tm->tm_sec);
> err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
> @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> return -EIO;
> }
>
> + /* Restore TWO bit */
> + if (restore_flags) {
> + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
> + flags &= ~NCT3018Y_BIT_TWO;
> +
> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> + if (err < 0) {
> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> + return err;
> + }
> + }
> +
> return err;
> }
>
> @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
> dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
> }
>
> - flags = NCT3018Y_BIT_TWO;
> - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> - if (err < 0) {
> - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
> - return err;
> + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
> + if (nct3018y->part_num < 0) {
> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
> + return nct3018y->part_num;
> + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
This is a weird way to check as this will accept any value of
NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
> + flags = NCT3018Y_BIT_HF;
> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> + if (err < 0) {
> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> + return err;
> + }
> }
>
> flags = 0;
> --
> 2.17.1
>
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
2023-11-03 23:16 ` Alexandre Belloni
@ 2023-11-03 23:17 ` Alexandre Belloni
-1 siblings, 0 replies; 12+ messages in thread
From: Alexandre Belloni @ 2023-11-03 23:17 UTC (permalink / raw)
To: Mia Lin
Cc: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, KWLIU, JJLIU0, KFLIN, mylin1, openbmc,
linux-rtc, linux-kernel
On 04/11/2023 00:16:40+0100, Alexandre Belloni wrote:
> On 13/09/2023 09:37:19+0800, Mia Lin wrote:
> > The NCT3015Y-R and NCT3018Y-R use the same datasheet
> > but have different topologies as follows.
> > - Topology (Only 1st i2c can set TWO bit and HF bit)
> > In NCT3015Y-R,
> > rtc 1st i2c is connected to a host CPU
> > rtc 2nd i2c is connected to a BMC
> > In NCT3018Y-R,
> > rtc 1st i2c is connected to a BMC
> > rtc 2nd i2c is connected to a host CPU
> > In order to be compatible with NCT3015Y-R and NCT3018Y-R,
> > - In probe,
> > If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
> > Else, do nothing
> > - In set_time,
> > If part number is NCT3018Y-R && TWO bit is 0,
> > change TWO bit to 1, and restore TWO bit after updating time.
> >
> > Signed-off-by: Mia Lin <mimi05633@gmail.com>
> > ---
I forgot to add, please include a changelog here, this will make my
reviews easier (and faster).
> > drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
> > 1 file changed, 46 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
> > index ed4e606be8e5..b006b58e15e2 100644
> > --- a/drivers/rtc/rtc-nct3018y.c
> > +++ b/drivers/rtc/rtc-nct3018y.c
> > @@ -23,6 +23,7 @@
> > #define NCT3018Y_REG_CTRL 0x0A /* timer control */
> > #define NCT3018Y_REG_ST 0x0B /* status */
> > #define NCT3018Y_REG_CLKO 0x0C /* clock out */
> > +#define NCT3018Y_REG_PART 0x21 /* part info */
> >
> > #define NCT3018Y_BIT_AF BIT(7)
> > #define NCT3018Y_BIT_ST BIT(7)
> > @@ -37,10 +38,12 @@
> > #define NCT3018Y_REG_BAT_MASK 0x07
> > #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
> > #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
> > +#define NCT3018Y_REG_PART_NCT3018Y 0x02
> >
> > struct nct3018y {
> > struct rtc_device *rtc;
> > struct i2c_client *client;
> > + int part_num;
> > #ifdef CONFIG_COMMON_CLK
> > struct clk_hw clkout_hw;
> > #endif
> > @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
> > static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> > {
> > struct i2c_client *client = to_i2c_client(dev);
> > + struct nct3018y *nct3018y = dev_get_drvdata(dev);
> > unsigned char buf[4] = {0};
> > - int err;
> > + int err, flags;
> > + int restore_flags = 0;
> > +
> > + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
> > + if (flags < 0) {
> > + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
> > + return flags;
> > + }
> > +
> > + /* Check and set TWO bit */
> > + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
> > + restore_flags = 1;
> > + flags |= NCT3018Y_BIT_TWO;
> > + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > + if (err < 0) {
> > + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> > + return err;
> > + }
> > + }
> >
> > buf[0] = bin2bcd(tm->tm_sec);
> > err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
> > @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> > return -EIO;
> > }
> >
> > + /* Restore TWO bit */
> > + if (restore_flags) {
> > + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
> > + flags &= ~NCT3018Y_BIT_TWO;
> > +
> > + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > + if (err < 0) {
> > + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> > + return err;
> > + }
> > + }
> > +
> > return err;
> > }
> >
> > @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
> > dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
> > }
> >
> > - flags = NCT3018Y_BIT_TWO;
> > - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > - if (err < 0) {
> > - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
> > - return err;
> > + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
> > + if (nct3018y->part_num < 0) {
> > + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
> > + return nct3018y->part_num;
> > + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
>
> This is a weird way to check as this will accept any value of
> NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
>
> > + flags = NCT3018Y_BIT_HF;
> > + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > + if (err < 0) {
> > + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> > + return err;
> > + }
> > }
> >
> > flags = 0;
> > --
> > 2.17.1
> >
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-11-03 23:17 ` Alexandre Belloni
0 siblings, 0 replies; 12+ messages in thread
From: Alexandre Belloni @ 2023-11-03 23:17 UTC (permalink / raw)
To: Mia Lin
Cc: linux-rtc, a.zummo, mylin1, benjaminfair, KWLIU, avifishman70,
venture, openbmc, JJLIU0, linux-kernel, tali.perry1, KFLIN,
tmaimon77
On 04/11/2023 00:16:40+0100, Alexandre Belloni wrote:
> On 13/09/2023 09:37:19+0800, Mia Lin wrote:
> > The NCT3015Y-R and NCT3018Y-R use the same datasheet
> > but have different topologies as follows.
> > - Topology (Only 1st i2c can set TWO bit and HF bit)
> > In NCT3015Y-R,
> > rtc 1st i2c is connected to a host CPU
> > rtc 2nd i2c is connected to a BMC
> > In NCT3018Y-R,
> > rtc 1st i2c is connected to a BMC
> > rtc 2nd i2c is connected to a host CPU
> > In order to be compatible with NCT3015Y-R and NCT3018Y-R,
> > - In probe,
> > If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
> > Else, do nothing
> > - In set_time,
> > If part number is NCT3018Y-R && TWO bit is 0,
> > change TWO bit to 1, and restore TWO bit after updating time.
> >
> > Signed-off-by: Mia Lin <mimi05633@gmail.com>
> > ---
I forgot to add, please include a changelog here, this will make my
reviews easier (and faster).
> > drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
> > 1 file changed, 46 insertions(+), 6 deletions(-)
> >
> > diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
> > index ed4e606be8e5..b006b58e15e2 100644
> > --- a/drivers/rtc/rtc-nct3018y.c
> > +++ b/drivers/rtc/rtc-nct3018y.c
> > @@ -23,6 +23,7 @@
> > #define NCT3018Y_REG_CTRL 0x0A /* timer control */
> > #define NCT3018Y_REG_ST 0x0B /* status */
> > #define NCT3018Y_REG_CLKO 0x0C /* clock out */
> > +#define NCT3018Y_REG_PART 0x21 /* part info */
> >
> > #define NCT3018Y_BIT_AF BIT(7)
> > #define NCT3018Y_BIT_ST BIT(7)
> > @@ -37,10 +38,12 @@
> > #define NCT3018Y_REG_BAT_MASK 0x07
> > #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
> > #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
> > +#define NCT3018Y_REG_PART_NCT3018Y 0x02
> >
> > struct nct3018y {
> > struct rtc_device *rtc;
> > struct i2c_client *client;
> > + int part_num;
> > #ifdef CONFIG_COMMON_CLK
> > struct clk_hw clkout_hw;
> > #endif
> > @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
> > static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> > {
> > struct i2c_client *client = to_i2c_client(dev);
> > + struct nct3018y *nct3018y = dev_get_drvdata(dev);
> > unsigned char buf[4] = {0};
> > - int err;
> > + int err, flags;
> > + int restore_flags = 0;
> > +
> > + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
> > + if (flags < 0) {
> > + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
> > + return flags;
> > + }
> > +
> > + /* Check and set TWO bit */
> > + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
> > + restore_flags = 1;
> > + flags |= NCT3018Y_BIT_TWO;
> > + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > + if (err < 0) {
> > + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> > + return err;
> > + }
> > + }
> >
> > buf[0] = bin2bcd(tm->tm_sec);
> > err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
> > @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
> > return -EIO;
> > }
> >
> > + /* Restore TWO bit */
> > + if (restore_flags) {
> > + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
> > + flags &= ~NCT3018Y_BIT_TWO;
> > +
> > + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > + if (err < 0) {
> > + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> > + return err;
> > + }
> > + }
> > +
> > return err;
> > }
> >
> > @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
> > dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
> > }
> >
> > - flags = NCT3018Y_BIT_TWO;
> > - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > - if (err < 0) {
> > - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
> > - return err;
> > + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
> > + if (nct3018y->part_num < 0) {
> > + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
> > + return nct3018y->part_num;
> > + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
>
> This is a weird way to check as this will accept any value of
> NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
>
> > + flags = NCT3018Y_BIT_HF;
> > + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
> > + if (err < 0) {
> > + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
> > + return err;
> > + }
> > }
> >
> > flags = 0;
> > --
> > 2.17.1
> >
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
2023-11-03 23:16 ` Alexandre Belloni
@ 2023-11-09 12:31 ` Mining Lin
-1 siblings, 0 replies; 12+ messages in thread
From: Mining Lin @ 2023-11-09 12:31 UTC (permalink / raw)
To: Alexandre Belloni
Cc: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, KWLIU, JJLIU0, KFLIN, mylin1, openbmc,
linux-rtc, linux-kernel
Dear Alexandre,
Thanks for your comments.
The replies are as follow.
Thanks.
Best regard,
Mia
Sent from my iPhone
> On Nov 4, 2023, at 7:16 AM, Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:
>
> On 13/09/2023 09:37:19+0800, Mia Lin wrote:
>> The NCT3015Y-R and NCT3018Y-R use the same datasheet
>> but have different topologies as follows.
>> - Topology (Only 1st i2c can set TWO bit and HF bit)
>> In NCT3015Y-R,
>> rtc 1st i2c is connected to a host CPU
>> rtc 2nd i2c is connected to a BMC
>> In NCT3018Y-R,
>> rtc 1st i2c is connected to a BMC
>> rtc 2nd i2c is connected to a host CPU
>> In order to be compatible with NCT3015Y-R and NCT3018Y-R,
>> - In probe,
>> If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
>> Else, do nothing
>> - In set_time,
>> If part number is NCT3018Y-R && TWO bit is 0,
>> change TWO bit to 1, and restore TWO bit after updating time.
>>
>> Signed-off-by: Mia Lin <mimi05633@gmail.com>
>> ---
>> drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
>> 1 file changed, 46 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
>> index ed4e606be8e5..b006b58e15e2 100644
>> --- a/drivers/rtc/rtc-nct3018y.c
>> +++ b/drivers/rtc/rtc-nct3018y.c
>> @@ -23,6 +23,7 @@
>> #define NCT3018Y_REG_CTRL 0x0A /* timer control */
>> #define NCT3018Y_REG_ST 0x0B /* status */
>> #define NCT3018Y_REG_CLKO 0x0C /* clock out */
>> +#define NCT3018Y_REG_PART 0x21 /* part info */
>>
>> #define NCT3018Y_BIT_AF BIT(7)
>> #define NCT3018Y_BIT_ST BIT(7)
>> @@ -37,10 +38,12 @@
>> #define NCT3018Y_REG_BAT_MASK 0x07
>> #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
>> #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
>> +#define NCT3018Y_REG_PART_NCT3018Y 0x02
>>
>> struct nct3018y {
>> struct rtc_device *rtc;
>> struct i2c_client *client;
>> + int part_num;
>> #ifdef CONFIG_COMMON_CLK
>> struct clk_hw clkout_hw;
>> #endif
>> @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
>> static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>> {
>> struct i2c_client *client = to_i2c_client(dev);
>> + struct nct3018y *nct3018y = dev_get_drvdata(dev);
>> unsigned char buf[4] = {0};
>> - int err;
>> + int err, flags;
>> + int restore_flags = 0;
>> +
>> + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
>> + if (flags < 0) {
>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
>> + return flags;
>> + }
>> +
>> + /* Check and set TWO bit */
>> + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
>> + restore_flags = 1;
>> + flags |= NCT3018Y_BIT_TWO;
>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> + if (err < 0) {
>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>> + return err;
>> + }
>> + }
>>
>> buf[0] = bin2bcd(tm->tm_sec);
>> err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
>> @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>> return -EIO;
>> }
>>
>> + /* Restore TWO bit */
>> + if (restore_flags) {
>> + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
>> + flags &= ~NCT3018Y_BIT_TWO;
>> +
>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> + if (err < 0) {
>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>> + return err;
>> + }
>> + }
>> +
>> return err;
>> }
>>
>> @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
>> dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
>> }
>>
>> - flags = NCT3018Y_BIT_TWO;
>> - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> - if (err < 0) {
>> - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
>> - return err;
>> + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
>> + if (nct3018y->part_num < 0) {
>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
>> + return nct3018y->part_num;
>> + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
>
> This is a weird way to check as this will accept any value of
> NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
[Mia] Thanks for your comments. I’ll fix it.
>
>> + flags = NCT3018Y_BIT_HF;
>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> + if (err < 0) {
>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>> + return err;
>> + }
>> }
>>
>> flags = 0;
>> --
>> 2.17.1
>>
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-11-09 12:31 ` Mining Lin
0 siblings, 0 replies; 12+ messages in thread
From: Mining Lin @ 2023-11-09 12:31 UTC (permalink / raw)
To: Alexandre Belloni
Cc: linux-rtc, a.zummo, mylin1, benjaminfair, KWLIU, avifishman70,
venture, openbmc, JJLIU0, linux-kernel, tali.perry1, KFLIN,
tmaimon77
Dear Alexandre,
Thanks for your comments.
The replies are as follow.
Thanks.
Best regard,
Mia
Sent from my iPhone
> On Nov 4, 2023, at 7:16 AM, Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:
>
> On 13/09/2023 09:37:19+0800, Mia Lin wrote:
>> The NCT3015Y-R and NCT3018Y-R use the same datasheet
>> but have different topologies as follows.
>> - Topology (Only 1st i2c can set TWO bit and HF bit)
>> In NCT3015Y-R,
>> rtc 1st i2c is connected to a host CPU
>> rtc 2nd i2c is connected to a BMC
>> In NCT3018Y-R,
>> rtc 1st i2c is connected to a BMC
>> rtc 2nd i2c is connected to a host CPU
>> In order to be compatible with NCT3015Y-R and NCT3018Y-R,
>> - In probe,
>> If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
>> Else, do nothing
>> - In set_time,
>> If part number is NCT3018Y-R && TWO bit is 0,
>> change TWO bit to 1, and restore TWO bit after updating time.
>>
>> Signed-off-by: Mia Lin <mimi05633@gmail.com>
>> ---
>> drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
>> 1 file changed, 46 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
>> index ed4e606be8e5..b006b58e15e2 100644
>> --- a/drivers/rtc/rtc-nct3018y.c
>> +++ b/drivers/rtc/rtc-nct3018y.c
>> @@ -23,6 +23,7 @@
>> #define NCT3018Y_REG_CTRL 0x0A /* timer control */
>> #define NCT3018Y_REG_ST 0x0B /* status */
>> #define NCT3018Y_REG_CLKO 0x0C /* clock out */
>> +#define NCT3018Y_REG_PART 0x21 /* part info */
>>
>> #define NCT3018Y_BIT_AF BIT(7)
>> #define NCT3018Y_BIT_ST BIT(7)
>> @@ -37,10 +38,12 @@
>> #define NCT3018Y_REG_BAT_MASK 0x07
>> #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
>> #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
>> +#define NCT3018Y_REG_PART_NCT3018Y 0x02
>>
>> struct nct3018y {
>> struct rtc_device *rtc;
>> struct i2c_client *client;
>> + int part_num;
>> #ifdef CONFIG_COMMON_CLK
>> struct clk_hw clkout_hw;
>> #endif
>> @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
>> static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>> {
>> struct i2c_client *client = to_i2c_client(dev);
>> + struct nct3018y *nct3018y = dev_get_drvdata(dev);
>> unsigned char buf[4] = {0};
>> - int err;
>> + int err, flags;
>> + int restore_flags = 0;
>> +
>> + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
>> + if (flags < 0) {
>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
>> + return flags;
>> + }
>> +
>> + /* Check and set TWO bit */
>> + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
>> + restore_flags = 1;
>> + flags |= NCT3018Y_BIT_TWO;
>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> + if (err < 0) {
>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>> + return err;
>> + }
>> + }
>>
>> buf[0] = bin2bcd(tm->tm_sec);
>> err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
>> @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>> return -EIO;
>> }
>>
>> + /* Restore TWO bit */
>> + if (restore_flags) {
>> + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
>> + flags &= ~NCT3018Y_BIT_TWO;
>> +
>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> + if (err < 0) {
>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>> + return err;
>> + }
>> + }
>> +
>> return err;
>> }
>>
>> @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
>> dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
>> }
>>
>> - flags = NCT3018Y_BIT_TWO;
>> - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> - if (err < 0) {
>> - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
>> - return err;
>> + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
>> + if (nct3018y->part_num < 0) {
>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
>> + return nct3018y->part_num;
>> + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
>
> This is a weird way to check as this will accept any value of
> NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
[Mia] Thanks for your comments. I’ll fix it.
>
>> + flags = NCT3018Y_BIT_HF;
>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>> + if (err < 0) {
>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>> + return err;
>> + }
>> }
>>
>> flags = 0;
>> --
>> 2.17.1
>>
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
2023-11-03 23:17 ` Alexandre Belloni
@ 2023-11-09 12:33 ` Mining Lin
-1 siblings, 0 replies; 12+ messages in thread
From: Mining Lin @ 2023-11-09 12:33 UTC (permalink / raw)
To: Alexandre Belloni
Cc: avifishman70, tmaimon77, tali.perry1, venture, yuenn,
benjaminfair, a.zummo, KWLIU, JJLIU0, KFLIN, mylin1, openbmc,
linux-rtc, linux-kernel
Dear Alexandre,
I will add change log next patch.
Thanks.
Best regard,
Mia
Sent from my iPhone
> On Nov 4, 2023, at 7:17 AM, Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:
>
> On 04/11/2023 00:16:40+0100, Alexandre Belloni wrote:
>>> On 13/09/2023 09:37:19+0800, Mia Lin wrote:
>>> The NCT3015Y-R and NCT3018Y-R use the same datasheet
>>> but have different topologies as follows.
>>> - Topology (Only 1st i2c can set TWO bit and HF bit)
>>> In NCT3015Y-R,
>>> rtc 1st i2c is connected to a host CPU
>>> rtc 2nd i2c is connected to a BMC
>>> In NCT3018Y-R,
>>> rtc 1st i2c is connected to a BMC
>>> rtc 2nd i2c is connected to a host CPU
>>> In order to be compatible with NCT3015Y-R and NCT3018Y-R,
>>> - In probe,
>>> If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
>>> Else, do nothing
>>> - In set_time,
>>> If part number is NCT3018Y-R && TWO bit is 0,
>>> change TWO bit to 1, and restore TWO bit after updating time.
>>>
>>> Signed-off-by: Mia Lin <mimi05633@gmail.com>
>>> ---
>
> I forgot to add, please include a changelog here, this will make my
> reviews easier (and faster).
>
>>> drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
>>> 1 file changed, 46 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
>>> index ed4e606be8e5..b006b58e15e2 100644
>>> --- a/drivers/rtc/rtc-nct3018y.c
>>> +++ b/drivers/rtc/rtc-nct3018y.c
>>> @@ -23,6 +23,7 @@
>>> #define NCT3018Y_REG_CTRL 0x0A /* timer control */
>>> #define NCT3018Y_REG_ST 0x0B /* status */
>>> #define NCT3018Y_REG_CLKO 0x0C /* clock out */
>>> +#define NCT3018Y_REG_PART 0x21 /* part info */
>>>
>>> #define NCT3018Y_BIT_AF BIT(7)
>>> #define NCT3018Y_BIT_ST BIT(7)
>>> @@ -37,10 +38,12 @@
>>> #define NCT3018Y_REG_BAT_MASK 0x07
>>> #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
>>> #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
>>> +#define NCT3018Y_REG_PART_NCT3018Y 0x02
>>>
>>> struct nct3018y {
>>> struct rtc_device *rtc;
>>> struct i2c_client *client;
>>> + int part_num;
>>> #ifdef CONFIG_COMMON_CLK
>>> struct clk_hw clkout_hw;
>>> #endif
>>> @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
>>> static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>>> {
>>> struct i2c_client *client = to_i2c_client(dev);
>>> + struct nct3018y *nct3018y = dev_get_drvdata(dev);
>>> unsigned char buf[4] = {0};
>>> - int err;
>>> + int err, flags;
>>> + int restore_flags = 0;
>>> +
>>> + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
>>> + if (flags < 0) {
>>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
>>> + return flags;
>>> + }
>>> +
>>> + /* Check and set TWO bit */
>>> + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
>>> + restore_flags = 1;
>>> + flags |= NCT3018Y_BIT_TWO;
>>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> + if (err < 0) {
>>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>>> + return err;
>>> + }
>>> + }
>>>
>>> buf[0] = bin2bcd(tm->tm_sec);
>>> err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
>>> @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>>> return -EIO;
>>> }
>>>
>>> + /* Restore TWO bit */
>>> + if (restore_flags) {
>>> + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
>>> + flags &= ~NCT3018Y_BIT_TWO;
>>> +
>>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> + if (err < 0) {
>>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>>> + return err;
>>> + }
>>> + }
>>> +
>>> return err;
>>> }
>>>
>>> @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
>>> dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
>>> }
>>>
>>> - flags = NCT3018Y_BIT_TWO;
>>> - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> - if (err < 0) {
>>> - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
>>> - return err;
>>> + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
>>> + if (nct3018y->part_num < 0) {
>>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
>>> + return nct3018y->part_num;
>>> + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
>>
>> This is a weird way to check as this will accept any value of
>> NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
>>
>>> + flags = NCT3018Y_BIT_HF;
>>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> + if (err < 0) {
>>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>>> + return err;
>>> + }
>>> }
>>>
>>> flags = 0;
>>> --
>>> 2.17.1
>>>
>>
>> --
>> Alexandre Belloni, co-owner and COO, Bootlin
>> Embedded Linux and Kernel engineering
>> https://bootlin.com
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v6 1/1] rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
@ 2023-11-09 12:33 ` Mining Lin
0 siblings, 0 replies; 12+ messages in thread
From: Mining Lin @ 2023-11-09 12:33 UTC (permalink / raw)
To: Alexandre Belloni
Cc: linux-rtc, a.zummo, mylin1, benjaminfair, KWLIU, avifishman70,
venture, openbmc, JJLIU0, linux-kernel, tali.perry1, KFLIN,
tmaimon77
Dear Alexandre,
I will add change log next patch.
Thanks.
Best regard,
Mia
Sent from my iPhone
> On Nov 4, 2023, at 7:17 AM, Alexandre Belloni <alexandre.belloni@bootlin.com> wrote:
>
> On 04/11/2023 00:16:40+0100, Alexandre Belloni wrote:
>>> On 13/09/2023 09:37:19+0800, Mia Lin wrote:
>>> The NCT3015Y-R and NCT3018Y-R use the same datasheet
>>> but have different topologies as follows.
>>> - Topology (Only 1st i2c can set TWO bit and HF bit)
>>> In NCT3015Y-R,
>>> rtc 1st i2c is connected to a host CPU
>>> rtc 2nd i2c is connected to a BMC
>>> In NCT3018Y-R,
>>> rtc 1st i2c is connected to a BMC
>>> rtc 2nd i2c is connected to a host CPU
>>> In order to be compatible with NCT3015Y-R and NCT3018Y-R,
>>> - In probe,
>>> If part number is NCT3018Y-R, only set HF bit to 24-Hour format.
>>> Else, do nothing
>>> - In set_time,
>>> If part number is NCT3018Y-R && TWO bit is 0,
>>> change TWO bit to 1, and restore TWO bit after updating time.
>>>
>>> Signed-off-by: Mia Lin <mimi05633@gmail.com>
>>> ---
>
> I forgot to add, please include a changelog here, this will make my
> reviews easier (and faster).
>
>>> drivers/rtc/rtc-nct3018y.c | 52 +++++++++++++++++++++++++++++++++-----
>>> 1 file changed, 46 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
>>> index ed4e606be8e5..b006b58e15e2 100644
>>> --- a/drivers/rtc/rtc-nct3018y.c
>>> +++ b/drivers/rtc/rtc-nct3018y.c
>>> @@ -23,6 +23,7 @@
>>> #define NCT3018Y_REG_CTRL 0x0A /* timer control */
>>> #define NCT3018Y_REG_ST 0x0B /* status */
>>> #define NCT3018Y_REG_CLKO 0x0C /* clock out */
>>> +#define NCT3018Y_REG_PART 0x21 /* part info */
>>>
>>> #define NCT3018Y_BIT_AF BIT(7)
>>> #define NCT3018Y_BIT_ST BIT(7)
>>> @@ -37,10 +38,12 @@
>>> #define NCT3018Y_REG_BAT_MASK 0x07
>>> #define NCT3018Y_REG_CLKO_F_MASK 0x03 /* frequenc mask */
>>> #define NCT3018Y_REG_CLKO_CKE 0x80 /* clock out enabled */
>>> +#define NCT3018Y_REG_PART_NCT3018Y 0x02
>>>
>>> struct nct3018y {
>>> struct rtc_device *rtc;
>>> struct i2c_client *client;
>>> + int part_num;
>>> #ifdef CONFIG_COMMON_CLK
>>> struct clk_hw clkout_hw;
>>> #endif
>>> @@ -177,8 +180,27 @@ static int nct3018y_rtc_read_time(struct device *dev, struct rtc_time *tm)
>>> static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>>> {
>>> struct i2c_client *client = to_i2c_client(dev);
>>> + struct nct3018y *nct3018y = dev_get_drvdata(dev);
>>> unsigned char buf[4] = {0};
>>> - int err;
>>> + int err, flags;
>>> + int restore_flags = 0;
>>> +
>>> + flags = i2c_smbus_read_byte_data(client, NCT3018Y_REG_CTRL);
>>> + if (flags < 0) {
>>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_CTRL.\n");
>>> + return flags;
>>> + }
>>> +
>>> + /* Check and set TWO bit */
>>> + if ((nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) && !(flags & NCT3018Y_BIT_TWO)) {
>>> + restore_flags = 1;
>>> + flags |= NCT3018Y_BIT_TWO;
>>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> + if (err < 0) {
>>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>>> + return err;
>>> + }
>>> + }
>>>
>>> buf[0] = bin2bcd(tm->tm_sec);
>>> err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_SC, buf[0]);
>>> @@ -212,6 +234,18 @@ static int nct3018y_rtc_set_time(struct device *dev, struct rtc_time *tm)
>>> return -EIO;
>>> }
>>>
>>> + /* Restore TWO bit */
>>> + if (restore_flags) {
>>> + if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y)
>>> + flags &= ~NCT3018Y_BIT_TWO;
>>> +
>>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> + if (err < 0) {
>>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>>> + return err;
>>> + }
>>> + }
>>> +
>>> return err;
>>> }
>>>
>>> @@ -479,11 +513,17 @@ static int nct3018y_probe(struct i2c_client *client)
>>> dev_dbg(&client->dev, "%s: NCT3018Y_BIT_TWO is set\n", __func__);
>>> }
>>>
>>> - flags = NCT3018Y_BIT_TWO;
>>> - err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> - if (err < 0) {
>>> - dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL\n");
>>> - return err;
>>> + nct3018y->part_num = i2c_smbus_read_byte_data(client, NCT3018Y_REG_PART);
>>> + if (nct3018y->part_num < 0) {
>>> + dev_dbg(&client->dev, "Failed to read NCT3018Y_REG_PART.\n");
>>> + return nct3018y->part_num;
>>> + } else if (nct3018y->part_num & NCT3018Y_REG_PART_NCT3018Y) {
>>
>> This is a weird way to check as this will accept any value of
>> NCT3018Y_REG_PART as long as bit 1 is set, is this really what you want?
>>
>>> + flags = NCT3018Y_BIT_HF;
>>> + err = i2c_smbus_write_byte_data(client, NCT3018Y_REG_CTRL, flags);
>>> + if (err < 0) {
>>> + dev_dbg(&client->dev, "Unable to write NCT3018Y_REG_CTRL.\n");
>>> + return err;
>>> + }
>>> }
>>>
>>> flags = 0;
>>> --
>>> 2.17.1
>>>
>>
>> --
>> Alexandre Belloni, co-owner and COO, Bootlin
>> Embedded Linux and Kernel engineering
>> https://bootlin.com
>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2023-11-09 12:34 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-09-13 1:37 [PATCH v6 0/1] Compatible with NCT3015Y-R and NCT3018Y-R Mia Lin
2023-09-13 1:37 ` Mia Lin
2023-09-13 1:37 ` [PATCH v6 1/1] rtc: nuvoton: " Mia Lin
2023-09-13 1:37 ` Mia Lin
2023-11-03 23:16 ` Alexandre Belloni
2023-11-03 23:16 ` Alexandre Belloni
2023-11-03 23:17 ` Alexandre Belloni
2023-11-03 23:17 ` Alexandre Belloni
2023-11-09 12:33 ` Mining Lin
2023-11-09 12:33 ` Mining Lin
2023-11-09 12:31 ` Mining Lin
2023-11-09 12:31 ` Mining Lin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.