* [PATCH 0/3] sunxi: devicetree updates from Linux v6.6
@ 2023-10-20 0:26 Andre Przywara
2023-10-20 0:26 ` [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 Andre Przywara
` (3 more replies)
0 siblings, 4 replies; 5+ messages in thread
From: Andre Przywara @ 2023-10-20 0:26 UTC (permalink / raw)
To: Jagan Teki
Cc: Jernej Skrabec, Samuel Holland, u-boot, linux-sunxi, Simon Glass,
Tom Rini, Ludwig Kormann
This updates the devicetree files to match the Linux kernel repository
as of v6.6-rc6.
Mostly cosmetic changes, but we gain some new board files and the T113s
board .dtsi files, which are needed for the pending U-Boot patches.
Split per architecture, with the T113s being separate due to its RISC-V
relationship.
Andre Przywara (3):
sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6
sunxi: dts: arm: update devicetree files from Linux-v6.6-rc6
sunxi: dts: arm: add T113s/D1 DT files from Linux-v6.6-rc6
arch/arm/dts/axp209.dtsi | 7 +
arch/arm/dts/sun50i-a64.dtsi | 3 +-
arch/arm/dts/sun50i-h6-pine-h64-model-b.dts | 2 +-
arch/arm/dts/sun50i-h616-orangepi-zero.dtsi | 134 +++
arch/arm/dts/sun50i-h616-orangepi-zero2.dts | 121 +--
arch/arm/dts/sun50i-h616-x96-mate.dts | 2 +-
arch/arm/dts/sun50i-h618-orangepi-zero3.dts | 94 ++
arch/arm/dts/sun5i-r8-chip.dts | 6 +
arch/arm/dts/sun5i.dtsi | 11 +-
arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts | 137 +++
arch/arm/dts/sun7i-a20-icnova-a20.dtsi | 62 ++
arch/arm/dts/sun8i-a23-a33.dtsi | 2 +-
arch/arm/dts/sun8i-a83t.dtsi | 2 +-
.../arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts | 35 +
arch/arm/dts/sun8i-t113s.dtsi | 59 ++
arch/arm/dts/sun8i-v3s.dtsi | 2 +-
arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi | 126 +++
arch/riscv/dts/sunxi-d1-t113.dtsi | 15 +
arch/riscv/dts/sunxi-d1s-t113.dtsi | 927 ++++++++++++++++++
include/dt-bindings/clock/sun20i-d1-ccu.h | 158 +++
include/dt-bindings/clock/sun20i-d1-r-ccu.h | 19 +
include/dt-bindings/clock/sun50i-h6-ccu.h | 2 +-
include/dt-bindings/clock/sun50i-h616-ccu.h | 2 +-
include/dt-bindings/clock/sun6i-rtc.h | 2 +-
include/dt-bindings/reset/sun20i-d1-ccu.h | 79 ++
include/dt-bindings/reset/sun20i-d1-r-ccu.h | 16 +
include/dt-bindings/reset/sun50i-h6-ccu.h | 2 +-
include/dt-bindings/reset/sun50i-h6-r-ccu.h | 2 +-
include/dt-bindings/reset/sun50i-h616-ccu.h | 2 +-
29 files changed, 1899 insertions(+), 132 deletions(-)
create mode 100644 arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
create mode 100644 arch/arm/dts/sun50i-h618-orangepi-zero3.dts
create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20.dtsi
create mode 100644 arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
create mode 100644 arch/arm/dts/sun8i-t113s.dtsi
create mode 100644 arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
create mode 100644 arch/riscv/dts/sunxi-d1-t113.dtsi
create mode 100644 arch/riscv/dts/sunxi-d1s-t113.dtsi
create mode 100644 include/dt-bindings/clock/sun20i-d1-ccu.h
create mode 100644 include/dt-bindings/clock/sun20i-d1-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun20i-d1-ccu.h
create mode 100644 include/dt-bindings/reset/sun20i-d1-r-ccu.h
--
2.35.8
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
@ 2023-10-20 0:26 ` Andre Przywara
2023-10-20 0:26 ` [PATCH 2/3] sunxi: dts: arm: " Andre Przywara
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Andre Przywara @ 2023-10-20 0:26 UTC (permalink / raw)
To: Jagan Teki
Cc: Jernej Skrabec, Samuel Holland, u-boot, linux-sunxi, Simon Glass,
Tom Rini, Ludwig Kormann
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 64-bit ARM cores.
Only small cosmetic changes (clock name fixed), but we add the DT for
the new OrangePi Zero 3 board, for which U-Boot enablement patches are
pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm/dts/sun50i-a64.dtsi | 3 +-
arch/arm/dts/sun50i-h6-pine-h64-model-b.dts | 2 +-
arch/arm/dts/sun50i-h616-orangepi-zero.dtsi | 134 ++++++++++++++++++++
arch/arm/dts/sun50i-h616-orangepi-zero2.dts | 121 +-----------------
arch/arm/dts/sun50i-h616-x96-mate.dts | 2 +-
arch/arm/dts/sun50i-h618-orangepi-zero3.dts | 94 ++++++++++++++
include/dt-bindings/clock/sun50i-h6-ccu.h | 2 +-
include/dt-bindings/clock/sun50i-h616-ccu.h | 2 +-
include/dt-bindings/clock/sun6i-rtc.h | 2 +-
include/dt-bindings/reset/sun50i-h6-ccu.h | 2 +-
include/dt-bindings/reset/sun50i-h6-r-ccu.h | 2 +-
include/dt-bindings/reset/sun50i-h616-ccu.h | 2 +-
12 files changed, 240 insertions(+), 128 deletions(-)
create mode 100644 arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
create mode 100644 arch/arm/dts/sun50i-h618-orangepi-zero3.dts
diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi
index 135762b34fd..2240eaec5dd 100644
--- a/arch/arm/dts/sun50i-a64.dtsi
+++ b/arch/arm/dts/sun50i-a64.dtsi
@@ -93,6 +93,7 @@
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
+ cache-unified;
};
};
@@ -407,7 +408,7 @@
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
clock-names = "ahb", "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
reset-names = "lcd", "lvds";
diff --git a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
index 686f58e7700..b710f1a0f53 100644
--- a/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
+++ b/arch/arm/dts/sun50i-h6-pine-h64-model-b.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2019 Corentin LABBE <clabbe@baylibre.com>
*/
diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
new file mode 100644
index 00000000000..15290e6892f
--- /dev/null
+++ b/arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ *
+ * DT nodes common between Orange Pi Zero 2 and Orange Pi Zero 3.
+ * Excludes PMIC nodes and properties, since they are different between the two.
+ */
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: regulator-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ /*
+ * PHY0 pins are connected to a USB-C socket, but a role switch
+ * is not implemented: both CC pins are pulled to GND.
+ * The VBUS pins power the device, so a fixed peripheral mode
+ * is the best choice.
+ * The board can be powered via GPIOs, in this case port0 *can*
+ * act as a host (with a cable/adapter ignoring CC), as VBUS is
+ * then provided by the GPIOs. Any user of this setup would
+ * need to adjust the DT accordingly: dr_mode set to "host",
+ * enabling OHCI0 and EHCI0.
+ */
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
index cb8600d0ea1..d83852e72f0 100644
--- a/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
+++ b/arch/arm/dts/sun50i-h616-orangepi-zero2.dts
@@ -1,99 +1,23 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2020 Arm Ltd.
*/
/dts-v1/;
-#include "sun50i-h616.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/leds/common.h>
+#include "sun50i-h616-orangepi-zero.dtsi"
/ {
model = "OrangePi Zero2";
compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
-
- aliases {
- ethernet0 = &emac0;
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-0 {
- function = LED_FUNCTION_POWER;
- color = <LED_COLOR_ID_RED>;
- gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
- default-state = "on";
- };
-
- led-1 {
- function = LED_FUNCTION_STATUS;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
- };
- };
-
- reg_vcc5v: vcc5v {
- /* board wide 5V supply directly from the USB-C socket */
- compatible = "regulator-fixed";
- regulator-name = "vcc-5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- reg_usb1_vbus: regulator-usb1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb1-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <®_vcc5v>;
- enable-active-high;
- gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
- };
};
-&ehci1 {
- status = "okay";
-};
-
-/* USB 2 & 3 are on headers only. */
-
&emac0 {
- pinctrl-names = "default";
- pinctrl-0 = <&ext_rgmii_pins>;
- phy-mode = "rgmii";
- phy-handle = <&ext_rgmii_phy>;
phy-supply = <®_dcdce>;
- allwinner,rx-delay-ps = <3100>;
- allwinner,tx-delay-ps = <700>;
- status = "okay";
-};
-
-&mdio0 {
- ext_rgmii_phy: ethernet-phy@1 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <1>;
- };
};
&mmc0 {
vmmc-supply = <®_dcdce>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
- bus-width = <4>;
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
};
&r_rsb {
@@ -211,44 +135,3 @@
vcc-ph-supply = <®_aldo1>;
vcc-pi-supply = <®_aldo1>;
};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
-
- flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <40000000>;
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
-};
-
-&usbotg {
- /*
- * PHY0 pins are connected to a USB-C socket, but a role switch
- * is not implemented: both CC pins are pulled to GND.
- * The VBUS pins power the device, so a fixed peripheral mode
- * is the best choice.
- * The board can be powered via GPIOs, in this case port0 *can*
- * act as a host (with a cable/adapter ignoring CC), as VBUS is
- * then provided by the GPIOs. Any user of this setup would
- * need to adjust the DT accordingly: dr_mode set to "host",
- * enabling OHCI0 and EHCI0.
- */
- dr_mode = "peripheral";
- status = "okay";
-};
-
-&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
- status = "okay";
-};
diff --git a/arch/arm/dts/sun50i-h616-x96-mate.dts b/arch/arm/dts/sun50i-h616-x96-mate.dts
index 07424c28b69..959b6fd1848 100644
--- a/arch/arm/dts/sun50i-h616-x96-mate.dts
+++ b/arch/arm/dts/sun50i-h616-x96-mate.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2021 Arm Ltd.
*/
diff --git a/arch/arm/dts/sun50i-h618-orangepi-zero3.dts b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts
new file mode 100644
index 00000000000..00fe28caac9
--- /dev/null
+++ b/arch/arm/dts/sun50i-h618-orangepi-zero3.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2023 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616-orangepi-zero.dtsi"
+
+/ {
+ model = "OrangePi Zero3";
+ compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
+};
+
+&emac0 {
+ phy-supply = <®_dldo1>;
+};
+
+&ext_rgmii_phy {
+ motorcomm,clk-out-frequency-hz = <125000000>;
+};
+
+&mmc0 {
+ /*
+ * The schematic shows the card detect pin wired up to PF6, via an
+ * inverter, but it just doesn't work.
+ */
+ broken-cd;
+ vmmc-supply = <®_dldo1>;
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp313: pmic@36 {
+ compatible = "x-powers,axp313a";
+ reg = <0x36>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-parent = <&pio>;
+ interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>; /* PC9 */
+
+ vin1-supply = <®_vcc5v>;
+ vin2-supply = <®_vcc5v>;
+ vin3-supply = <®_vcc5v>;
+
+ regulators {
+ /* Supplies VCC-PLL, so needs to be always on. */
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ /* Supplies VCC-IO, so needs to be always on. */
+ reg_dldo1: dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-dram";
+ };
+ };
+ };
+};
+
+&pio {
+ vcc-pc-supply = <®_dldo1>;
+ vcc-pf-supply = <®_dldo1>;
+ vcc-pg-supply = <®_aldo1>;
+ vcc-ph-supply = <®_dldo1>;
+ vcc-pi-supply = <®_dldo1>;
+};
diff --git a/include/dt-bindings/clock/sun50i-h6-ccu.h b/include/dt-bindings/clock/sun50i-h6-ccu.h
index a1545cd60e7..ef9123d8193 100644
--- a/include/dt-bindings/clock/sun50i-h6-ccu.h
+++ b/include/dt-bindings/clock/sun50i-h6-ccu.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*/
diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h
index 1191aca53ac..6f8f01e6762 100644
--- a/include/dt-bindings/clock/sun50i-h616-ccu.h
+++ b/include/dt-bindings/clock/sun50i-h616-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2020 Arm Ltd.
*/
diff --git a/include/dt-bindings/clock/sun6i-rtc.h b/include/dt-bindings/clock/sun6i-rtc.h
index c845493e4d3..3bd3aa3d57c 100644
--- a/include/dt-bindings/clock/sun6i-rtc.h
+++ b/include/dt-bindings/clock/sun6i-rtc.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
#ifndef _DT_BINDINGS_CLK_SUN6I_RTC_H_
#define _DT_BINDINGS_CLK_SUN6I_RTC_H_
diff --git a/include/dt-bindings/reset/sun50i-h6-ccu.h b/include/dt-bindings/reset/sun50i-h6-ccu.h
index 81106f45509..d038ddfa481 100644
--- a/include/dt-bindings/reset/sun50i-h6-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h6-ccu.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
*/
diff --git a/include/dt-bindings/reset/sun50i-h6-r-ccu.h b/include/dt-bindings/reset/sun50i-h6-r-ccu.h
index 7950e799c76..d541ade884f 100644
--- a/include/dt-bindings/reset/sun50i-h6-r-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h6-r-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
*/
diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h
index cb6285a8d12..1bd8bb0a11b 100644
--- a/include/dt-bindings/reset/sun50i-h616-ccu.h
+++ b/include/dt-bindings/reset/sun50i-h616-ccu.h
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
/*
* Copyright (C) 2020 Arm Ltd.
*/
--
2.35.8
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/3] sunxi: dts: arm: update devicetree files from Linux-v6.6-rc6
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
2023-10-20 0:26 ` [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 Andre Przywara
@ 2023-10-20 0:26 ` Andre Przywara
2023-10-20 0:26 ` [PATCH 3/3] sunxi: dts: arm: add T113s/D1 DT " Andre Przywara
2023-10-21 7:49 ` [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Jernej Škrabec
3 siblings, 0 replies; 5+ messages in thread
From: Andre Przywara @ 2023-10-20 0:26 UTC (permalink / raw)
To: Jagan Teki
Cc: Jernej Skrabec, Samuel Holland, u-boot, linux-sunxi, Simon Glass,
Tom Rini, Ludwig Kormann
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 32-bit ARM cores, minus the T113s
board and related .dtsi files, which come separately.
Only small changes: Bluetooth got enabled on the C.H.I.P., and a clock
got renamed. More interesting is the addition of a board, for which
U-Boot enablement patches are pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm/dts/axp209.dtsi | 7 +
arch/arm/dts/sun5i-r8-chip.dts | 6 +
arch/arm/dts/sun5i.dtsi | 11 +-
arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts | 137 ++++++++++++++++++
arch/arm/dts/sun7i-a20-icnova-a20.dtsi | 62 ++++++++
arch/arm/dts/sun8i-a23-a33.dtsi | 2 +-
arch/arm/dts/sun8i-a83t.dtsi | 2 +-
arch/arm/dts/sun8i-v3s.dtsi | 2 +-
8 files changed, 225 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20.dtsi
diff --git a/arch/arm/dts/axp209.dtsi b/arch/arm/dts/axp209.dtsi
index ca240cd6f6c..469d0f7d518 100644
--- a/arch/arm/dts/axp209.dtsi
+++ b/arch/arm/dts/axp209.dtsi
@@ -48,6 +48,13 @@
* http://dl.linux-sunxi.org/AXP/AXP209%20Datasheet%20v1.0_cn.pdf
*/
+/ {
+ pmic-temp {
+ compatible = "iio-hwmon";
+ io-channels = <&axp_adc 4>; /* Internal temperature */
+ };
+};
+
&axp209 {
compatible = "x-powers,axp209";
interrupt-controller;
diff --git a/arch/arm/dts/sun5i-r8-chip.dts b/arch/arm/dts/sun5i-r8-chip.dts
index fd37bd1f392..4192c23848c 100644
--- a/arch/arm/dts/sun5i-r8-chip.dts
+++ b/arch/arm/dts/sun5i-r8-chip.dts
@@ -255,6 +255,12 @@
pinctrl-0 = <&uart3_pg_pins>,
<&uart3_cts_rts_pg_pins>;
status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8723bs-bt";
+ device-wake-gpios = <&axp_gpio 3 GPIO_ACTIVE_HIGH>;
+ host-wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+ };
};
&usb_otg {
diff --git a/arch/arm/dts/sun5i.dtsi b/arch/arm/dts/sun5i.dtsi
index 250d6b87ab4..d7c7b454a11 100644
--- a/arch/arm/dts/sun5i.dtsi
+++ b/arch/arm/dts/sun5i.dtsi
@@ -286,7 +286,7 @@
clock-names = "ahb",
"tcon-ch0",
"tcon-ch1";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
status = "disabled";
@@ -517,6 +517,15 @@
bias-pull-up;
};
+ /omit-if-no-ref/
+ mmc2_4bit_pe_pins: mmc2-4bit-pe-pins {
+ pins = "PE4", "PE5", "PE6", "PE7",
+ "PE8", "PE9";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
mmc2_8bit_pins: mmc2-8bit-pins {
pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11", "PC12", "PC13",
diff --git a/arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts b/arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
new file mode 100644
index 00000000000..577ead1d02a
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+/dts-v1/;
+
+#include "sun7i-a20-icnova-a20.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "In-Circuit ICnova A20 ADB4006";
+ compatible = "incircuit,icnova-a20-adb4006", "incircuit,icnova-a20",
+ "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_YELLOW>;
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+&ac_power_supply {
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/sun7i-a20-icnova-a20.dtsi b/arch/arm/dts/sun7i-a20-icnova-a20.dtsi
new file mode 100644
index 00000000000..46616c6bc89
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-icnova-a20.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_mii_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "mii";
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&gmac_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
diff --git a/arch/arm/dts/sun8i-a23-a33.dtsi b/arch/arm/dts/sun8i-a23-a33.dtsi
index 84c6d9379a3..a0cac966af3 100644
--- a/arch/arm/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/dts/sun8i-a23-a33.dtsi
@@ -190,7 +190,7 @@
clock-names = "ahb",
"tcon-ch0",
"lvds-alt";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_LCD>,
<&ccu RST_BUS_LVDS>;
diff --git a/arch/arm/dts/sun8i-a83t.dtsi b/arch/arm/dts/sun8i-a83t.dtsi
index 9c07660080d..cc40622466a 100644
--- a/arch/arm/dts/sun8i-a83t.dtsi
+++ b/arch/arm/dts/sun8i-a83t.dtsi
@@ -456,7 +456,7 @@
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
clock-names = "ahb", "tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
reset-names = "lcd", "lvds";
diff --git a/arch/arm/dts/sun8i-v3s.dtsi b/arch/arm/dts/sun8i-v3s.dtsi
index b001251644f..3b9a282c274 100644
--- a/arch/arm/dts/sun8i-v3s.dtsi
+++ b/arch/arm/dts/sun8i-v3s.dtsi
@@ -191,7 +191,7 @@
<&ccu CLK_TCON0>;
clock-names = "ahb",
"tcon-ch0";
- clock-output-names = "tcon-pixel-clock";
+ clock-output-names = "tcon-data-clock";
#clock-cells = <0>;
resets = <&ccu RST_BUS_TCON0>;
reset-names = "lcd";
--
2.35.8
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 3/3] sunxi: dts: arm: add T113s/D1 DT files from Linux-v6.6-rc6
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
2023-10-20 0:26 ` [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 Andre Przywara
2023-10-20 0:26 ` [PATCH 2/3] sunxi: dts: arm: " Andre Przywara
@ 2023-10-20 0:26 ` Andre Przywara
2023-10-21 7:49 ` [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Jernej Škrabec
3 siblings, 0 replies; 5+ messages in thread
From: Andre Przywara @ 2023-10-20 0:26 UTC (permalink / raw)
To: Jagan Teki
Cc: Jernej Skrabec, Samuel Holland, u-boot, linux-sunxi, Simon Glass,
Tom Rini, Ludwig Kormann
This copies in some devicetree files from the official Linux kernel tree,
v6.6-rc6. It covers a board with the Allwinner T113s SoC, which shares
many devices with its RISC-V sibling, the Allwinner D1(s). This is the
reason for the core .dtsi files landing in the arch/riscv directory.
We are only adjusting the include path to accommodate for the differences
in the U-Boot build system.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts | 35 +
arch/arm/dts/sun8i-t113s.dtsi | 59 ++
arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi | 126 +++
arch/riscv/dts/sunxi-d1-t113.dtsi | 15 +
arch/riscv/dts/sunxi-d1s-t113.dtsi | 927 ++++++++++++++++++
include/dt-bindings/clock/sun20i-d1-ccu.h | 158 +++
include/dt-bindings/clock/sun20i-d1-r-ccu.h | 19 +
include/dt-bindings/reset/sun20i-d1-ccu.h | 79 ++
include/dt-bindings/reset/sun20i-d1-r-ccu.h | 16 +
9 files changed, 1434 insertions(+)
create mode 100644 arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
create mode 100644 arch/arm/dts/sun8i-t113s.dtsi
create mode 100644 arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
create mode 100644 arch/riscv/dts/sunxi-d1-t113.dtsi
create mode 100644 arch/riscv/dts/sunxi-d1s-t113.dtsi
create mode 100644 include/dt-bindings/clock/sun20i-d1-ccu.h
create mode 100644 include/dt-bindings/clock/sun20i-d1-r-ccu.h
create mode 100644 include/dt-bindings/reset/sun20i-d1-ccu.h
create mode 100644 include/dt-bindings/reset/sun20i-d1-r-ccu.h
diff --git a/arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts b/arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
new file mode 100644
index 00000000000..8b3a7538381
--- /dev/null
+++ b/arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+
+#include "sun8i-t113s.dtsi"
+#include "sunxi-d1s-t113-mangopi-mq-r.dtsi"
+
+/ {
+ model = "MangoPi MQ-R-T113";
+ compatible = "widora,mangopi-mq-r-t113", "allwinner,sun8i-t113s";
+
+ aliases {
+ ethernet0 = &rtl8189ftv;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vcc_core>;
+};
+
+&cpu1 {
+ cpu-supply = <®_vcc_core>;
+};
+
+&mmc1 {
+ rtl8189ftv: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 = WL_WAKE_AP */
+ interrupt-names = "host-wake";
+ };
+};
diff --git a/arch/arm/dts/sun8i-t113s.dtsi b/arch/arm/dts/sun8i-t113s.dtsi
new file mode 100644
index 00000000000..b94b69142af
--- /dev/null
+++ b/arch/arm/dts/sun8i-t113s.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#define SOC_PERIPHERAL_IRQ(nr) GIC_SPI nr
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <../../riscv/dts/sunxi-d1s-t113.dtsi>
+#include <../../riscv/dts/sunxi-d1-t113.dtsi>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ };
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x03021000 0x1000>,
+ <0x03022000 0x2000>,
+ <0x03024000 0x2000>,
+ <0x03026000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>;
+ };
+};
diff --git a/arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi b/arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
new file mode 100644
index 00000000000..a415c4a78a7
--- /dev/null
+++ b/arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+/*
+ * Common peripherals and configurations for MangoPi MQ-R boards.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ aliases {
+ serial3 = &uart3;
+ };
+
+ chosen {
+ stdout-path = "serial3:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
+ };
+ };
+
+ /* board wide 5V supply directly from the USB-C socket */
+ reg_vcc5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ /* SY8008 DC/DC regulator on the board */
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_vcc5v>;
+ };
+
+ /* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+ reg_vcc_core: regulator-core {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-core";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ vin-supply = <®_vcc5v>;
+ };
+
+ /* XC6206 LDO on the board */
+ reg_avdd2v8: regulator-avdd {
+ compatible = "regulator-fixed";
+ regulator-name = "avdd2v8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_3v3>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+ };
+};
+
+&dcxo {
+ clock-frequency = <24000000>;
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <®_3v3>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-0 = <&mmc1_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <®_3v3>;
+ non-removable;
+ bus-width = <4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pb-supply = <®_3v3>;
+ vcc-pd-supply = <®_3v3>;
+ vcc-pe-supply = <®_avdd2v8>;
+ vcc-pf-supply = <®_3v3>;
+ vcc-pg-supply = <®_3v3>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pb_pins>;
+ status = "okay";
+};
+
+/* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_vcc5v>;
+ status = "okay";
+};
diff --git a/arch/riscv/dts/sunxi-d1-t113.dtsi b/arch/riscv/dts/sunxi-d1-t113.dtsi
new file mode 100644
index 00000000000..b7156123df5
--- /dev/null
+++ b/arch/riscv/dts/sunxi-d1-t113.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+/ {
+ soc {
+ dsp_wdt: watchdog@1700400 {
+ compatible = "allwinner,sun20i-d1-wdt";
+ reg = <0x1700400 0x20>;
+ interrupts = <SOC_PERIPHERAL_IRQ(122) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+ clock-names = "hosc", "losc";
+ status = "reserved";
+ };
+ };
+};
diff --git a/arch/riscv/dts/sunxi-d1s-t113.dtsi b/arch/riscv/dts/sunxi-d1s-t113.dtsi
new file mode 100644
index 00000000000..822f022eec2
--- /dev/null
+++ b/arch/riscv/dts/sunxi-d1s-t113.dtsi
@@ -0,0 +1,927 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/clock/sun8i-de2.h>
+#include <dt-bindings/clock/sun8i-tcon-top.h>
+#include <dt-bindings/clock/sun20i-d1-ccu.h>
+#include <dt-bindings/clock/sun20i-d1-r-ccu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun20i-d1-ccu.h>
+#include <dt-bindings/reset/sun20i-d1-r-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ dcxo: dcxo-clk {
+ compatible = "fixed-clock";
+ clock-output-names = "dcxo";
+ #clock-cells = <0>;
+ };
+
+ de: display-engine {
+ compatible = "allwinner,sun20i-d1-display-engine";
+ allwinner,pipelines = <&mixer0>, <&mixer1>;
+ status = "disabled";
+ };
+
+ soc {
+ compatible = "simple-bus";
+ ranges;
+ dma-noncoherent;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ pio: pinctrl@2000000 {
+ compatible = "allwinner,sun20i-d1-pinctrl";
+ reg = <0x2000000 0x800>;
+ interrupts = <SOC_PERIPHERAL_IRQ(69) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(71) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(73) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(75) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(77) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(79) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB0>,
+ <&dcxo>,
+ <&rtc CLK_OSC32K>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ interrupt-controller;
+ #gpio-cells = <3>;
+ #interrupt-cells = <3>;
+
+ /omit-if-no-ref/
+ can0_pins: can0-pins {
+ pins = "PB2", "PB3";
+ function = "can0";
+ };
+
+ /omit-if-no-ref/
+ can1_pins: can1-pins {
+ pins = "PB4", "PB5";
+ function = "can1";
+ };
+
+ /omit-if-no-ref/
+ clk_pg11_pin: clk-pg11-pin {
+ pins = "PG11";
+ function = "clk";
+ };
+
+ /omit-if-no-ref/
+ dsi_4lane_pins: dsi-4lane-pins {
+ pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+ "PD6", "PD7", "PD8", "PD9";
+ drive-strength = <30>;
+ function = "dsi";
+ };
+
+ /omit-if-no-ref/
+ lcd_rgb666_pins: lcd-rgb666-pins {
+ pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+ "PD6", "PD7", "PD8", "PD9", "PD10", "PD11",
+ "PD12", "PD13", "PD14", "PD15", "PD16", "PD17",
+ "PD18", "PD19", "PD20", "PD21";
+ function = "lcd0";
+ };
+
+ /omit-if-no-ref/
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+ function = "mmc0";
+ };
+
+ /omit-if-no-ref/
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5";
+ function = "mmc1";
+ };
+
+ /omit-if-no-ref/
+ mmc2_pins: mmc2-pins {
+ pins = "PC2", "PC3", "PC4", "PC5", "PC6", "PC7";
+ function = "mmc2";
+ };
+
+ /omit-if-no-ref/
+ rgmii_pe_pins: rgmii-pe-pins {
+ pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+ "PE5", "PE6", "PE7", "PE8", "PE9",
+ "PE11", "PE12", "PE13", "PE14", "PE15";
+ function = "emac";
+ };
+
+ /omit-if-no-ref/
+ rmii_pe_pins: rmii-pe-pins {
+ pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+ "PE5", "PE6", "PE7", "PE8", "PE9";
+ function = "emac";
+ };
+
+ /omit-if-no-ref/
+ spi0_pins: spi0-pins {
+ pins = "PC2", "PC3", "PC4", "PC5";
+ function = "spi0";
+ };
+
+ /omit-if-no-ref/
+ uart1_pg6_pins: uart1-pg6-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ /omit-if-no-ref/
+ uart1_pg8_rts_cts_pins: uart1-pg8-rts-cts-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ /omit-if-no-ref/
+ uart3_pb_pins: uart3-pb-pins {
+ pins = "PB6", "PB7";
+ function = "uart3";
+ };
+ };
+
+ ccu: clock-controller@2001000 {
+ compatible = "allwinner,sun20i-d1-ccu";
+ reg = <0x2001000 0x1000>;
+ clocks = <&dcxo>,
+ <&rtc CLK_OSC32K>,
+ <&rtc CLK_IOSC>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ gpadc: adc@2009000 {
+ compatible = "allwinner,sun20i-d1-gpadc";
+ reg = <0x2009000 0x400>;
+ clocks = <&ccu CLK_BUS_GPADC>;
+ resets = <&ccu RST_BUS_GPADC>;
+ interrupts = <SOC_PERIPHERAL_IRQ(57) IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #io-channel-cells = <1>;
+ };
+
+ dmic: dmic@2031000 {
+ compatible = "allwinner,sun20i-d1-dmic",
+ "allwinner,sun50i-h6-dmic";
+ reg = <0x2031000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(24) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMIC>,
+ <&ccu CLK_DMIC>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_DMIC>;
+ dmas = <&dma 8>;
+ dma-names = "rx";
+ status = "disabled";
+ #sound-dai-cells = <0>;
+ };
+
+ i2s1: i2s@2033000 {
+ compatible = "allwinner,sun20i-d1-i2s",
+ "allwinner,sun50i-r329-i2s";
+ reg = <0x2033000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(27) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S1>,
+ <&ccu CLK_I2S1>;
+ clock-names = "apb", "mod";
+ resets = <&ccu RST_BUS_I2S1>;
+ dmas = <&dma 4>, <&dma 4>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #sound-dai-cells = <0>;
+ };
+
+ i2s2: i2s@2034000 {
+ compatible = "allwinner,sun20i-d1-i2s",
+ "allwinner,sun50i-r329-i2s";
+ reg = <0x2034000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(28) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S2>,
+ <&ccu CLK_I2S2>;
+ clock-names = "apb", "mod";
+ resets = <&ccu RST_BUS_I2S2>;
+ dmas = <&dma 5>, <&dma 5>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #sound-dai-cells = <0>;
+ };
+
+ timer: timer@2050000 {
+ compatible = "allwinner,sun20i-d1-timer",
+ "allwinner,sun8i-a23-timer";
+ reg = <0x2050000 0xa0>;
+ interrupts = <SOC_PERIPHERAL_IRQ(59) IRQ_TYPE_LEVEL_HIGH>,
+ <SOC_PERIPHERAL_IRQ(60) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&dcxo>;
+ };
+
+ wdt: watchdog@20500a0 {
+ compatible = "allwinner,sun20i-d1-wdt-reset",
+ "allwinner,sun20i-d1-wdt";
+ reg = <0x20500a0 0x20>;
+ interrupts = <SOC_PERIPHERAL_IRQ(63) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&dcxo>, <&rtc CLK_OSC32K>;
+ clock-names = "hosc", "losc";
+ status = "reserved";
+ };
+
+ uart0: serial@2500000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500000 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(2) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 14>, <&dma 14>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart1: serial@2500400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500400 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(3) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart2: serial@2500800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500800 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(4) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 16>, <&dma 16>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart3: serial@2500c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2500c00 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(5) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 17>, <&dma 17>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart4: serial@2501000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2501000 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(6) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ dmas = <&dma 18>, <&dma 18>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart5: serial@2501400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x2501400 0x400>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ interrupts = <SOC_PERIPHERAL_IRQ(7) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ dmas = <&dma 19>, <&dma 19>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@2502000 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(9) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ dmas = <&dma 43>, <&dma 43>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@2502400 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502400 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(10) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ dmas = <&dma 44>, <&dma 44>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@2502800 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502800 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(11) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ dmas = <&dma 45>, <&dma 45>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@2502c00 {
+ compatible = "allwinner,sun20i-d1-i2c",
+ "allwinner,sun8i-v536-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x2502c00 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(12) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ dmas = <&dma 46>, <&dma 46>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ can0: can@2504000 {
+ compatible = "allwinner,sun20i-d1-can";
+ reg = <0x02504000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(21) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CAN0>;
+ resets = <&ccu RST_BUS_CAN0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins>;
+ status = "disabled";
+ };
+
+ can1: can@2504400 {
+ compatible = "allwinner,sun20i-d1-can";
+ reg = <0x02504400 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(22) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CAN1>;
+ resets = <&ccu RST_BUS_CAN1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins>;
+ status = "disabled";
+ };
+
+ syscon: syscon@3000000 {
+ compatible = "allwinner,sun20i-d1-system-control";
+ reg = <0x3000000 0x1000>;
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ dma: dma-controller@3002000 {
+ compatible = "allwinner,sun20i-d1-dma";
+ reg = <0x3002000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(50) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+ clock-names = "bus", "mbus";
+ resets = <&ccu RST_BUS_DMA>;
+ dma-channels = <16>;
+ dma-requests = <48>;
+ #dma-cells = <1>;
+ };
+
+ sid: efuse@3006000 {
+ compatible = "allwinner,sun20i-d1-sid";
+ reg = <0x3006000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ crypto: crypto@3040000 {
+ compatible = "allwinner,sun20i-d1-crypto";
+ reg = <0x3040000 0x800>;
+ interrupts = <SOC_PERIPHERAL_IRQ(52) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CE>,
+ <&ccu CLK_CE>,
+ <&ccu CLK_MBUS_CE>,
+ <&rtc CLK_IOSC>;
+ clock-names = "bus", "mod", "ram", "trng";
+ resets = <&ccu RST_BUS_CE>;
+ };
+
+ mbus: dram-controller@3102000 {
+ compatible = "allwinner,sun20i-d1-mbus";
+ reg = <0x3102000 0x1000>,
+ <0x3103000 0x1000>;
+ reg-names = "mbus", "dram";
+ interrupts = <SOC_PERIPHERAL_IRQ(43) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_MBUS>,
+ <&ccu CLK_DRAM>,
+ <&ccu CLK_BUS_DRAM>;
+ clock-names = "mbus", "dram", "bus";
+ dma-ranges = <0 0x40000000 0x80000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interconnect-cells = <1>;
+ };
+
+ mmc0: mmc@4020000 {
+ compatible = "allwinner,sun20i-d1-mmc";
+ reg = <0x4020000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(40) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ cap-sd-highspeed;
+ max-frequency = <150000000>;
+ no-mmc;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@4021000 {
+ compatible = "allwinner,sun20i-d1-mmc";
+ reg = <0x4021000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(41) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ cap-sd-highspeed;
+ max-frequency = <150000000>;
+ no-mmc;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@4022000 {
+ compatible = "allwinner,sun20i-d1-emmc",
+ "allwinner,sun50i-a100-emmc";
+ reg = <0x4022000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(42) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ cap-mmc-highspeed;
+ max-frequency = <150000000>;
+ mmc-ddr-1_8v;
+ mmc-ddr-3_3v;
+ no-sd;
+ no-sdio;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi@4025000 {
+ compatible = "allwinner,sun20i-d1-spi",
+ "allwinner,sun50i-r329-spi";
+ reg = <0x04025000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(15) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 22>, <&dma 22>;
+ dma-names = "rx", "tx";
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@4026000 {
+ compatible = "allwinner,sun20i-d1-spi-dbi",
+ "allwinner,sun50i-r329-spi-dbi",
+ "allwinner,sun50i-r329-spi";
+ reg = <0x04026000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(16) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usb_otg: usb@4100000 {
+ compatible = "allwinner,sun20i-d1-musb",
+ "allwinner,sun8i-a33-musb";
+ reg = <0x4100000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(29) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ extcon = <&usbphy 0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ usbphy: phy@4100400 {
+ compatible = "allwinner,sun20i-d1-usb-phy";
+ reg = <0x4100400 0x100>,
+ <0x4101800 0x100>,
+ <0x4200800 0x100>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1";
+ clocks = <&dcxo>,
+ <&dcxo>;
+ clock-names = "usb0_phy",
+ "usb1_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>;
+ reset-names = "usb0_reset",
+ "usb1_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@4101000 {
+ compatible = "allwinner,sun20i-d1-ehci",
+ "generic-ehci";
+ reg = <0x4101000 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(30) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_BUS_EHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>,
+ <&ccu RST_BUS_EHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@4101400 {
+ compatible = "allwinner,sun20i-d1-ohci",
+ "generic-ohci";
+ reg = <0x4101400 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(31) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb@4200000 {
+ compatible = "allwinner,sun20i-d1-ehci",
+ "generic-ehci";
+ reg = <0x4200000 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(33) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_BUS_EHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>,
+ <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@4200400 {
+ compatible = "allwinner,sun20i-d1-ohci",
+ "generic-ohci";
+ reg = <0x4200400 0x100>;
+ interrupts = <SOC_PERIPHERAL_IRQ(34) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ emac: ethernet@4500000 {
+ compatible = "allwinner,sun20i-d1-emac",
+ "allwinner,sun50i-a64-emac";
+ reg = <0x4500000 0x10000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(46) IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ syscon = <&syscon>;
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ display_clocks: clock-controller@5000000 {
+ compatible = "allwinner,sun20i-d1-de2-clk",
+ "allwinner,sun50i-h5-de2-clk";
+ reg = <0x5000000 0x10000>;
+ clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@5100000 {
+ compatible = "allwinner,sun20i-d1-de2-mixer-0";
+ reg = <0x5100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus", "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon_top_mixer0: endpoint {
+ remote-endpoint = <&tcon_top_mixer0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ mixer1: mixer@5200000 {
+ compatible = "allwinner,sun20i-d1-de2-mixer-1";
+ reg = <0x5200000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER1>,
+ <&display_clocks CLK_MIXER1>;
+ clock-names = "bus", "mod";
+ resets = <&display_clocks RST_MIXER1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer1_out: port@1 {
+ reg = <1>;
+
+ mixer1_out_tcon_top_mixer1: endpoint {
+ remote-endpoint = <&tcon_top_mixer1_in_mixer1>;
+ };
+ };
+ };
+ };
+
+ dsi: dsi@5450000 {
+ compatible = "allwinner,sun20i-d1-mipi-dsi",
+ "allwinner,sun50i-a100-mipi-dsi";
+ reg = <0x5450000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MIPI_DSI>,
+ <&tcon_top CLK_TCON_TOP_DSI>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_MIPI_DSI>;
+ phys = <&dphy>;
+ phy-names = "dphy";
+ status = "disabled";
+
+ port {
+ dsi_in_tcon_lcd0: endpoint {
+ remote-endpoint = <&tcon_lcd0_out_dsi>;
+ };
+ };
+ };
+
+ dphy: phy@5451000 {
+ compatible = "allwinner,sun20i-d1-mipi-dphy",
+ "allwinner,sun50i-a100-mipi-dphy";
+ reg = <0x5451000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(92) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MIPI_DSI>,
+ <&ccu CLK_MIPI_DSI>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_MIPI_DSI>;
+ #phy-cells = <0>;
+ };
+
+ tcon_top: tcon-top@5460000 {
+ compatible = "allwinner,sun20i-d1-tcon-top";
+ reg = <0x5460000 0x1000>;
+ clocks = <&ccu CLK_BUS_DPSS_TOP>,
+ <&ccu CLK_TCON_TV>,
+ <&ccu CLK_TVE>,
+ <&ccu CLK_TCON_LCD0>;
+ clock-names = "bus", "tcon-tv0", "tve0", "dsi";
+ clock-output-names = "tcon-top-tv0", "tcon-top-dsi";
+ resets = <&ccu RST_BUS_DPSS_TOP>;
+ #clock-cells = <1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer0_in: port@0 {
+ reg = <0>;
+
+ tcon_top_mixer0_in_mixer0: endpoint {
+ remote-endpoint = <&mixer0_out_tcon_top_mixer0>;
+ };
+ };
+
+ tcon_top_mixer0_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer0_out_tcon_lcd0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer0>;
+ };
+
+ tcon_top_mixer0_out_tcon_tv0: endpoint@2 {
+ reg = <2>;
+ remote-endpoint = <&tcon_tv0_in_tcon_top_mixer0>;
+ };
+ };
+
+ tcon_top_mixer1_in: port@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer1_in_mixer1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&mixer1_out_tcon_top_mixer1>;
+ };
+ };
+
+ tcon_top_mixer1_out: port@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_top_mixer1_out_tcon_lcd0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_lcd0_in_tcon_top_mixer1>;
+ };
+
+ tcon_top_mixer1_out_tcon_tv0: endpoint@2 {
+ reg = <2>;
+ remote-endpoint = <&tcon_tv0_in_tcon_top_mixer1>;
+ };
+ };
+
+ tcon_top_hdmi_in: port@4 {
+ reg = <4>;
+
+ tcon_top_hdmi_in_tcon_tv0: endpoint {
+ remote-endpoint = <&tcon_tv0_out_tcon_top_hdmi>;
+ };
+ };
+
+ tcon_top_hdmi_out: port@5 {
+ reg = <5>;
+ };
+ };
+ };
+
+ tcon_lcd0: lcd-controller@5461000 {
+ compatible = "allwinner,sun20i-d1-tcon-lcd";
+ reg = <0x5461000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(90) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON_LCD0>,
+ <&ccu CLK_TCON_LCD0>;
+ clock-names = "ahb", "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_TCON_LCD0>,
+ <&ccu RST_BUS_LVDS0>;
+ reset-names = "lcd", "lvds";
+ #clock-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_lcd0_in: port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_lcd0_in_tcon_top_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_top_mixer0_out_tcon_lcd0>;
+ };
+
+ tcon_lcd0_in_tcon_top_mixer1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon_top_mixer1_out_tcon_lcd0>;
+ };
+ };
+
+ tcon_lcd0_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_lcd0_out_dsi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dsi_in_tcon_lcd0>;
+ };
+ };
+ };
+ };
+
+ tcon_tv0: lcd-controller@5470000 {
+ compatible = "allwinner,sun20i-d1-tcon-tv";
+ reg = <0x5470000 0x1000>;
+ interrupts = <SOC_PERIPHERAL_IRQ(91) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON_TV>,
+ <&tcon_top CLK_TCON_TOP_TV0>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON_TV>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_tv0_in: port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon_tv0_in_tcon_top_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon_top_mixer0_out_tcon_tv0>;
+ };
+
+ tcon_tv0_in_tcon_top_mixer1: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tcon_top_mixer1_out_tcon_tv0>;
+ };
+ };
+
+ tcon_tv0_out: port@1 {
+ reg = <1>;
+
+ tcon_tv0_out_tcon_top_hdmi: endpoint {
+ remote-endpoint = <&tcon_top_hdmi_in_tcon_tv0>;
+ };
+ };
+ };
+ };
+
+ ppu: power-controller@7001000 {
+ compatible = "allwinner,sun20i-d1-ppu";
+ reg = <0x7001000 0x1000>;
+ clocks = <&r_ccu CLK_BUS_R_PPU>;
+ resets = <&r_ccu RST_BUS_R_PPU>;
+ #power-domain-cells = <1>;
+ };
+
+ r_ccu: clock-controller@7010000 {
+ compatible = "allwinner,sun20i-d1-r-ccu";
+ reg = <0x7010000 0x400>;
+ clocks = <&dcxo>,
+ <&rtc CLK_OSC32K>,
+ <&rtc CLK_IOSC>,
+ <&ccu CLK_PLL_PERIPH0_DIV3>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ rtc: rtc@7090000 {
+ compatible = "allwinner,sun20i-d1-rtc",
+ "allwinner,sun50i-r329-rtc";
+ reg = <0x7090000 0x400>;
+ interrupts = <SOC_PERIPHERAL_IRQ(144) IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_BUS_R_RTC>,
+ <&dcxo>,
+ <&r_ccu CLK_R_AHB>;
+ clock-names = "bus", "hosc", "ahb";
+ #clock-cells = <1>;
+ };
+ };
+};
diff --git a/include/dt-bindings/clock/sun20i-d1-ccu.h b/include/dt-bindings/clock/sun20i-d1-ccu.h
new file mode 100644
index 00000000000..fdbfb404f92
--- /dev/null
+++ b/include/dt-bindings/clock/sun20i-d1-ccu.h
@@ -0,0 +1,158 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2020 huangzhenwei@allwinnertech.com
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN20I_D1_CCU_H_
+#define _DT_BINDINGS_CLK_SUN20I_D1_CCU_H_
+
+#define CLK_PLL_CPUX 0
+#define CLK_PLL_DDR0 1
+#define CLK_PLL_PERIPH0_4X 2
+#define CLK_PLL_PERIPH0_2X 3
+#define CLK_PLL_PERIPH0_800M 4
+#define CLK_PLL_PERIPH0 5
+#define CLK_PLL_PERIPH0_DIV3 6
+#define CLK_PLL_VIDEO0_4X 7
+#define CLK_PLL_VIDEO0_2X 8
+#define CLK_PLL_VIDEO0 9
+#define CLK_PLL_VIDEO1_4X 10
+#define CLK_PLL_VIDEO1_2X 11
+#define CLK_PLL_VIDEO1 12
+#define CLK_PLL_VE 13
+#define CLK_PLL_AUDIO0_4X 14
+#define CLK_PLL_AUDIO0_2X 15
+#define CLK_PLL_AUDIO0 16
+#define CLK_PLL_AUDIO1 17
+#define CLK_PLL_AUDIO1_DIV2 18
+#define CLK_PLL_AUDIO1_DIV5 19
+#define CLK_CPUX 20
+#define CLK_CPUX_AXI 21
+#define CLK_CPUX_APB 22
+#define CLK_PSI_AHB 23
+#define CLK_APB0 24
+#define CLK_APB1 25
+#define CLK_MBUS 26
+#define CLK_DE 27
+#define CLK_BUS_DE 28
+#define CLK_DI 29
+#define CLK_BUS_DI 30
+#define CLK_G2D 31
+#define CLK_BUS_G2D 32
+#define CLK_CE 33
+#define CLK_BUS_CE 34
+#define CLK_VE 35
+#define CLK_BUS_VE 36
+#define CLK_BUS_DMA 37
+#define CLK_BUS_MSGBOX0 38
+#define CLK_BUS_MSGBOX1 39
+#define CLK_BUS_MSGBOX2 40
+#define CLK_BUS_SPINLOCK 41
+#define CLK_BUS_HSTIMER 42
+#define CLK_AVS 43
+#define CLK_BUS_DBG 44
+#define CLK_BUS_PWM 45
+#define CLK_BUS_IOMMU 46
+#define CLK_DRAM 47
+#define CLK_MBUS_DMA 48
+#define CLK_MBUS_VE 49
+#define CLK_MBUS_CE 50
+#define CLK_MBUS_TVIN 51
+#define CLK_MBUS_CSI 52
+#define CLK_MBUS_G2D 53
+#define CLK_MBUS_RISCV 54
+#define CLK_BUS_DRAM 55
+#define CLK_MMC0 56
+#define CLK_MMC1 57
+#define CLK_MMC2 58
+#define CLK_BUS_MMC0 59
+#define CLK_BUS_MMC1 60
+#define CLK_BUS_MMC2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_UART4 66
+#define CLK_BUS_UART5 67
+#define CLK_BUS_I2C0 68
+#define CLK_BUS_I2C1 69
+#define CLK_BUS_I2C2 70
+#define CLK_BUS_I2C3 71
+#define CLK_SPI0 72
+#define CLK_SPI1 73
+#define CLK_BUS_SPI0 74
+#define CLK_BUS_SPI1 75
+#define CLK_EMAC_25M 76
+#define CLK_BUS_EMAC 77
+#define CLK_IR_TX 78
+#define CLK_BUS_IR_TX 79
+#define CLK_BUS_GPADC 80
+#define CLK_BUS_THS 81
+#define CLK_I2S0 82
+#define CLK_I2S1 83
+#define CLK_I2S2 84
+#define CLK_I2S2_ASRC 85
+#define CLK_BUS_I2S0 86
+#define CLK_BUS_I2S1 87
+#define CLK_BUS_I2S2 88
+#define CLK_SPDIF_TX 89
+#define CLK_SPDIF_RX 90
+#define CLK_BUS_SPDIF 91
+#define CLK_DMIC 92
+#define CLK_BUS_DMIC 93
+#define CLK_AUDIO_DAC 94
+#define CLK_AUDIO_ADC 95
+#define CLK_BUS_AUDIO 96
+#define CLK_USB_OHCI0 97
+#define CLK_USB_OHCI1 98
+#define CLK_BUS_OHCI0 99
+#define CLK_BUS_OHCI1 100
+#define CLK_BUS_EHCI0 101
+#define CLK_BUS_EHCI1 102
+#define CLK_BUS_OTG 103
+#define CLK_BUS_LRADC 104
+#define CLK_BUS_DPSS_TOP 105
+#define CLK_HDMI_24M 106
+#define CLK_HDMI_CEC_32K 107
+#define CLK_HDMI_CEC 108
+#define CLK_BUS_HDMI 109
+#define CLK_MIPI_DSI 110
+#define CLK_BUS_MIPI_DSI 111
+#define CLK_TCON_LCD0 112
+#define CLK_BUS_TCON_LCD0 113
+#define CLK_TCON_TV 114
+#define CLK_BUS_TCON_TV 115
+#define CLK_TVE 116
+#define CLK_BUS_TVE_TOP 117
+#define CLK_BUS_TVE 118
+#define CLK_TVD 119
+#define CLK_BUS_TVD_TOP 120
+#define CLK_BUS_TVD 121
+#define CLK_LEDC 122
+#define CLK_BUS_LEDC 123
+#define CLK_CSI_TOP 124
+#define CLK_CSI_MCLK 125
+#define CLK_BUS_CSI 126
+#define CLK_TPADC 127
+#define CLK_BUS_TPADC 128
+#define CLK_BUS_TZMA 129
+#define CLK_DSP 130
+#define CLK_BUS_DSP_CFG 131
+#define CLK_RISCV 132
+#define CLK_RISCV_AXI 133
+#define CLK_BUS_RISCV_CFG 134
+#define CLK_FANOUT_24M 135
+#define CLK_FANOUT_12M 136
+#define CLK_FANOUT_16M 137
+#define CLK_FANOUT_25M 138
+#define CLK_FANOUT_32K 139
+#define CLK_FANOUT_27M 140
+#define CLK_FANOUT_PCLK 141
+#define CLK_FANOUT0 142
+#define CLK_FANOUT1 143
+#define CLK_FANOUT2 144
+#define CLK_BUS_CAN0 145
+#define CLK_BUS_CAN1 146
+
+#endif /* _DT_BINDINGS_CLK_SUN20I_D1_CCU_H_ */
diff --git a/include/dt-bindings/clock/sun20i-d1-r-ccu.h b/include/dt-bindings/clock/sun20i-d1-r-ccu.h
new file mode 100644
index 00000000000..f95c170711e
--- /dev/null
+++ b/include/dt-bindings/clock/sun20i-d1-r-ccu.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN20I_D1_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN20I_D1_R_CCU_H_
+
+#define CLK_R_AHB 0
+
+#define CLK_BUS_R_TIMER 2
+#define CLK_BUS_R_TWD 3
+#define CLK_BUS_R_PPU 4
+#define CLK_R_IR_RX 5
+#define CLK_BUS_R_IR_RX 6
+#define CLK_BUS_R_RTC 7
+#define CLK_BUS_R_CPUCFG 8
+
+#endif /* _DT_BINDINGS_CLK_SUN20I_D1_R_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun20i-d1-ccu.h b/include/dt-bindings/reset/sun20i-d1-ccu.h
new file mode 100644
index 00000000000..79e52aca591
--- /dev/null
+++ b/include/dt-bindings/reset/sun20i-d1-ccu.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (c) 2020 huangzhenwei@allwinnertech.com
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN20I_D1_CCU_H_
+#define _DT_BINDINGS_RST_SUN20I_D1_CCU_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_DI 2
+#define RST_BUS_G2D 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MSGBOX0 7
+#define RST_BUS_MSGBOX1 8
+#define RST_BUS_MSGBOX2 9
+#define RST_BUS_SPINLOCK 10
+#define RST_BUS_HSTIMER 11
+#define RST_BUS_DBG 12
+#define RST_BUS_PWM 13
+#define RST_BUS_DRAM 14
+#define RST_BUS_MMC0 15
+#define RST_BUS_MMC1 16
+#define RST_BUS_MMC2 17
+#define RST_BUS_UART0 18
+#define RST_BUS_UART1 19
+#define RST_BUS_UART2 20
+#define RST_BUS_UART3 21
+#define RST_BUS_UART4 22
+#define RST_BUS_UART5 23
+#define RST_BUS_I2C0 24
+#define RST_BUS_I2C1 25
+#define RST_BUS_I2C2 26
+#define RST_BUS_I2C3 27
+#define RST_BUS_SPI0 28
+#define RST_BUS_SPI1 29
+#define RST_BUS_EMAC 30
+#define RST_BUS_IR_TX 31
+#define RST_BUS_GPADC 32
+#define RST_BUS_THS 33
+#define RST_BUS_I2S0 34
+#define RST_BUS_I2S1 35
+#define RST_BUS_I2S2 36
+#define RST_BUS_SPDIF 37
+#define RST_BUS_DMIC 38
+#define RST_BUS_AUDIO 39
+#define RST_USB_PHY0 40
+#define RST_USB_PHY1 41
+#define RST_BUS_OHCI0 42
+#define RST_BUS_OHCI1 43
+#define RST_BUS_EHCI0 44
+#define RST_BUS_EHCI1 45
+#define RST_BUS_OTG 46
+#define RST_BUS_LRADC 47
+#define RST_BUS_DPSS_TOP 48
+#define RST_BUS_HDMI_SUB 49
+#define RST_BUS_HDMI_MAIN 50
+#define RST_BUS_MIPI_DSI 51
+#define RST_BUS_TCON_LCD0 52
+#define RST_BUS_TCON_TV 53
+#define RST_BUS_LVDS0 54
+#define RST_BUS_TVE 55
+#define RST_BUS_TVE_TOP 56
+#define RST_BUS_TVD 57
+#define RST_BUS_TVD_TOP 58
+#define RST_BUS_LEDC 59
+#define RST_BUS_CSI 60
+#define RST_BUS_TPADC 61
+#define RST_DSP 62
+#define RST_BUS_DSP_CFG 63
+#define RST_BUS_DSP_DBG 64
+#define RST_BUS_RISCV_CFG 65
+#define RST_BUS_CAN0 66
+#define RST_BUS_CAN1 67
+
+#endif /* _DT_BINDINGS_RST_SUN20I_D1_CCU_H_ */
diff --git a/include/dt-bindings/reset/sun20i-d1-r-ccu.h b/include/dt-bindings/reset/sun20i-d1-r-ccu.h
new file mode 100644
index 00000000000..e20babc990a
--- /dev/null
+++ b/include/dt-bindings/reset/sun20i-d1-r-ccu.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2021 Samuel Holland <samuel@sholland.org>
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN20I_D1_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN20I_D1_R_CCU_H_
+
+#define RST_BUS_R_TIMER 0
+#define RST_BUS_R_TWD 1
+#define RST_BUS_R_PPU 2
+#define RST_BUS_R_IR_RX 3
+#define RST_BUS_R_RTC 4
+#define RST_BUS_R_CPUCFG 5
+
+#endif /* _DT_BINDINGS_RST_SUN20I_D1_R_CCU_H_ */
--
2.35.8
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 0/3] sunxi: devicetree updates from Linux v6.6
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
` (2 preceding siblings ...)
2023-10-20 0:26 ` [PATCH 3/3] sunxi: dts: arm: add T113s/D1 DT " Andre Przywara
@ 2023-10-21 7:49 ` Jernej Škrabec
3 siblings, 0 replies; 5+ messages in thread
From: Jernej Škrabec @ 2023-10-21 7:49 UTC (permalink / raw)
To: Jagan Teki, Andre Przywara
Cc: Samuel Holland, u-boot, linux-sunxi, Simon Glass, Tom Rini,
Ludwig Kormann
On Friday, October 20, 2023 2:26:05 AM CEST Andre Przywara wrote:
> This updates the devicetree files to match the Linux kernel repository
> as of v6.6-rc6.
> Mostly cosmetic changes, but we gain some new board files and the T113s
> board .dtsi files, which are needed for the pending U-Boot patches.
>
> Split per architecture, with the T113s being separate due to its RISC-V
> relationship.
>
> Andre Przywara (3):
> sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6
> sunxi: dts: arm: update devicetree files from Linux-v6.6-rc6
> sunxi: dts: arm: add T113s/D1 DT files from Linux-v6.6-rc6
I compared all DTs and they are identical, except r_intc, as mentioned.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Best regards,
Jernej
>
> arch/arm/dts/axp209.dtsi | 7 +
> arch/arm/dts/sun50i-a64.dtsi | 3 +-
> arch/arm/dts/sun50i-h6-pine-h64-model-b.dts | 2 +-
> arch/arm/dts/sun50i-h616-orangepi-zero.dtsi | 134 +++
> arch/arm/dts/sun50i-h616-orangepi-zero2.dts | 121 +--
> arch/arm/dts/sun50i-h616-x96-mate.dts | 2 +-
> arch/arm/dts/sun50i-h618-orangepi-zero3.dts | 94 ++
> arch/arm/dts/sun5i-r8-chip.dts | 6 +
> arch/arm/dts/sun5i.dtsi | 11 +-
> arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts | 137 +++
> arch/arm/dts/sun7i-a20-icnova-a20.dtsi | 62 ++
> arch/arm/dts/sun8i-a23-a33.dtsi | 2 +-
> arch/arm/dts/sun8i-a83t.dtsi | 2 +-
> .../arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts | 35 +
> arch/arm/dts/sun8i-t113s.dtsi | 59 ++
> arch/arm/dts/sun8i-v3s.dtsi | 2 +-
> arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi | 126 +++
> arch/riscv/dts/sunxi-d1-t113.dtsi | 15 +
> arch/riscv/dts/sunxi-d1s-t113.dtsi | 927 ++++++++++++++++++
> include/dt-bindings/clock/sun20i-d1-ccu.h | 158 +++
> include/dt-bindings/clock/sun20i-d1-r-ccu.h | 19 +
> include/dt-bindings/clock/sun50i-h6-ccu.h | 2 +-
> include/dt-bindings/clock/sun50i-h616-ccu.h | 2 +-
> include/dt-bindings/clock/sun6i-rtc.h | 2 +-
> include/dt-bindings/reset/sun20i-d1-ccu.h | 79 ++
> include/dt-bindings/reset/sun20i-d1-r-ccu.h | 16 +
> include/dt-bindings/reset/sun50i-h6-ccu.h | 2 +-
> include/dt-bindings/reset/sun50i-h6-r-ccu.h | 2 +-
> include/dt-bindings/reset/sun50i-h616-ccu.h | 2 +-
> 29 files changed, 1899 insertions(+), 132 deletions(-)
> create mode 100644 arch/arm/dts/sun50i-h616-orangepi-zero.dtsi
> create mode 100644 arch/arm/dts/sun50i-h618-orangepi-zero3.dts
> create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts
> create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20.dtsi
> create mode 100644 arch/arm/dts/sun8i-t113s-mangopi-mq-r-t113.dts
> create mode 100644 arch/arm/dts/sun8i-t113s.dtsi
> create mode 100644 arch/arm/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
> create mode 100644 arch/riscv/dts/sunxi-d1-t113.dtsi
> create mode 100644 arch/riscv/dts/sunxi-d1s-t113.dtsi
> create mode 100644 include/dt-bindings/clock/sun20i-d1-ccu.h
> create mode 100644 include/dt-bindings/clock/sun20i-d1-r-ccu.h
> create mode 100644 include/dt-bindings/reset/sun20i-d1-ccu.h
> create mode 100644 include/dt-bindings/reset/sun20i-d1-r-ccu.h
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2023-10-21 7:49 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-10-20 0:26 [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Andre Przywara
2023-10-20 0:26 ` [PATCH 1/3] sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6 Andre Przywara
2023-10-20 0:26 ` [PATCH 2/3] sunxi: dts: arm: " Andre Przywara
2023-10-20 0:26 ` [PATCH 3/3] sunxi: dts: arm: add T113s/D1 DT " Andre Przywara
2023-10-21 7:49 ` [PATCH 0/3] sunxi: devicetree updates from Linux v6.6 Jernej Škrabec
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.