[PATCH 00/14] arm64: dts: imx8mm-kontron: DT updates

[PATCH 00/14] arm64: dts: imx8mm-kontron: DT updates

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This patchset contains several improvements and updates for the devicetrees
for the i.MX8MM modules and boards by Kontron Electronics GmbH.

* HDMI/LVDS support for the BL/DL i.MX8MM
* Misc cleanups and small fixes
* OSM-S i.MX8MM module refactoring and update to latest HW revision

Frieder Schrempf (14):
  arm64: dts: imx8mm-kontron: Add support for display bridges on BL
    i.MX8MM
  arm64: dts: imx8mm-kontron: Add DL (Display-Line) overlay with LVDS
    support
  arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S
    i.MX8MM
  arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL
    i.MX8MM
  arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals
    on BL OSM-S board
  arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals
    on BL board
  arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals
    on BL OSM-S board
  arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals
    on BL board
  arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM
    module
  arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest
    hardware
  arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX
  arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from
    RTC node
  arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM
  arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and
    board

 arch/arm64/boot/dts/freescale/Makefile        |   4 +
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 295 +++------
 .../boot/dts/freescale/imx8mm-kontron-bl.dts  | 187 +++++-
 .../boot/dts/freescale/imx8mm-kontron-dl.dtso | 197 ++++++
 .../dts/freescale/imx8mm-kontron-osm-s.dtsi   | 567 +++++++++++++++++-
 .../boot/dts/freescale/imx8mm-kontron-sl.dtsi |   4 +-
 6 files changed, 1020 insertions(+), 234 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso

-- 
2.42.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 00/14] arm64: dts: imx8mm-kontron: DT updates

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

This patchset contains several improvements and updates for the devicetrees
for the i.MX8MM modules and boards by Kontron Electronics GmbH.

* HDMI/LVDS support for the BL/DL i.MX8MM
* Misc cleanups and small fixes
* OSM-S i.MX8MM module refactoring and update to latest HW revision

Frieder Schrempf (14):
  arm64: dts: imx8mm-kontron: Add support for display bridges on BL
    i.MX8MM
  arm64: dts: imx8mm-kontron: Add DL (Display-Line) overlay with LVDS
    support
  arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S
    i.MX8MM
  arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL
    i.MX8MM
  arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals
    on BL OSM-S board
  arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals
    on BL board
  arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals
    on BL OSM-S board
  arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals
    on BL board
  arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM
    module
  arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest
    hardware
  arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX
  arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from
    RTC node
  arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM
  arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and
    board

 arch/arm64/boot/dts/freescale/Makefile        |   4 +
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 295 +++------
 .../boot/dts/freescale/imx8mm-kontron-bl.dts  | 187 +++++-
 .../boot/dts/freescale/imx8mm-kontron-dl.dtso | 197 ++++++
 .../dts/freescale/imx8mm-kontron-osm-s.dtsi   | 567 +++++++++++++++++-
 .../boot/dts/freescale/imx8mm-kontron-sl.dtsi |   4 +-
 6 files changed, 1020 insertions(+), 234 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso

-- 
2.42.0

[PATCH 01/14] arm64: dts: imx8mm-kontron: Add support for display bridges on BL i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Kontron Electronics BL i.MX8MM has oboard disply bridges for
DSI->HDMI and DSI->LVDS conversion. The DSI interface is muxed by
a GPIO-controlled switch to one of these two bridges.

By default the HDMI bridge is enabled. The LVDS bridge can be
selected by loading an additional (panel-specific) overlay.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts  | 149 ++++++++++++++++++
 1 file changed, 149 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index dcec57c20399e..f1326bf634a7f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -25,6 +25,17 @@ osc_can: clock-osc-can {
 		clock-output-names = "osc-can";
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_in_conn: endpoint {
+				remote-endpoint = <&bridge_out_conn>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -132,6 +143,93 @@ ethphy: ethernet-phy@0 {
 	};
 };
 
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+
+	dsi_mux_sel: dsi-mux-sel-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "dsi-mux-sel";
+	};
+
+	dsi-mux-oe-hog {
+		gpio-hog;
+		gpios = <15 GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "dsi-mux-oe";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	hdmi: hdmi@39 {
+		compatible = "adi,adv7535";
+		reg = <0x39>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_adv7535>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+
+		adi,dsi-lanes = <4>;
+
+		a2vdd-supply = <&reg_vdd_1v8>;
+		avdd-supply = <&reg_vdd_1v8>;
+		dvdd-supply = <&reg_vdd_1v8>;
+		pvdd-supply = <&reg_vdd_1v8>;
+		v1p2-supply = <&reg_vdd_1v8>;
+		v3p3-supply = <&reg_vdd_3v3>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi_hdmi: endpoint {
+					remote-endpoint = <&dsi_out_bridge>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				bridge_out_conn: endpoint {
+					remote-endpoint = <&hdmi_in_conn>;
+				};
+			};
+		};
+	};
+
+	lvds: bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sn65dsi84>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi_lvds: endpoint {
+					remote-endpoint = <&dsi_out_bridge>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+		};
+	};
+};
+
 &i2c4 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -144,6 +242,30 @@ rx8900: rtc@32 {
 	};
 };
 
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	samsung,esc-clock-frequency = <54000000>;
+	/*
+	 * Let the driver calculate an appropriate clock rate based on the pixel
+	 * clock instead of using the fixed value from imx8mm.dtsi.
+	 */
+	/delete-property/ samsung,pll-clock-frequency;
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			dsi_out_bridge: endpoint {
+				remote-endpoint = <&bridge_in_dsi_hdmi>;
+			};
+		};
+	};
+};
+
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
@@ -207,6 +329,12 @@ &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio>;
 
+	pinctrl_adv7535: adv7535grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x19
+		>;
+	};
+
 	pinctrl_can: cangrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
@@ -277,6 +405,20 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 		>;
 	};
 
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x19
+			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x19
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
@@ -290,6 +432,13 @@ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
 		>;
 	};
 
+	pinctrl_sn65dsi84: sn65dsi84grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26		0x19
+			MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x19
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 01/14] arm64: dts: imx8mm-kontron: Add support for display bridges on BL i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Kontron Electronics BL i.MX8MM has oboard disply bridges for
DSI->HDMI and DSI->LVDS conversion. The DSI interface is muxed by
a GPIO-controlled switch to one of these two bridges.

By default the HDMI bridge is enabled. The LVDS bridge can be
selected by loading an additional (panel-specific) overlay.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts  | 149 ++++++++++++++++++
 1 file changed, 149 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index dcec57c20399e..f1326bf634a7f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -25,6 +25,17 @@ osc_can: clock-osc-can {
 		clock-output-names = "osc-can";
 	};
 
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_in_conn: endpoint {
+				remote-endpoint = <&bridge_out_conn>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -132,6 +143,93 @@ ethphy: ethernet-phy@0 {
 	};
 };
 
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+
+	dsi_mux_sel: dsi-mux-sel-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "dsi-mux-sel";
+	};
+
+	dsi-mux-oe-hog {
+		gpio-hog;
+		gpios = <15 GPIO_ACTIVE_LOW>;
+		output-high;
+		line-name = "dsi-mux-oe";
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	hdmi: hdmi@39 {
+		compatible = "adi,adv7535";
+		reg = <0x39>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_adv7535>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+
+		adi,dsi-lanes = <4>;
+
+		a2vdd-supply = <&reg_vdd_1v8>;
+		avdd-supply = <&reg_vdd_1v8>;
+		dvdd-supply = <&reg_vdd_1v8>;
+		pvdd-supply = <&reg_vdd_1v8>;
+		v1p2-supply = <&reg_vdd_1v8>;
+		v3p3-supply = <&reg_vdd_3v3>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi_hdmi: endpoint {
+					remote-endpoint = <&dsi_out_bridge>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				bridge_out_conn: endpoint {
+					remote-endpoint = <&hdmi_in_conn>;
+				};
+			};
+		};
+	};
+
+	lvds: bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sn65dsi84>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi_lvds: endpoint {
+					remote-endpoint = <&dsi_out_bridge>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+		};
+	};
+};
+
 &i2c4 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -144,6 +242,30 @@ rx8900: rtc@32 {
 	};
 };
 
+&lcdif {
+	status = "okay";
+};
+
+&mipi_dsi {
+	samsung,esc-clock-frequency = <54000000>;
+	/*
+	 * Let the driver calculate an appropriate clock rate based on the pixel
+	 * clock instead of using the fixed value from imx8mm.dtsi.
+	 */
+	/delete-property/ samsung,pll-clock-frequency;
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			dsi_out_bridge: endpoint {
+				remote-endpoint = <&bridge_in_dsi_hdmi>;
+			};
+		};
+	};
+};
+
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
@@ -207,6 +329,12 @@ &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio>;
 
+	pinctrl_adv7535: adv7535grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x19
+		>;
+	};
+
 	pinctrl_can: cangrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
@@ -277,6 +405,20 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 		>;
 	};
 
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x19
+			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x19
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
@@ -290,6 +432,13 @@ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
 		>;
 	};
 
+	pinctrl_sn65dsi84: sn65dsi84grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26		0x19
+			MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x19
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-- 
2.42.0

[PATCH 02/14] arm64: dts: imx8mm-kontron: Add DL (Display-Line) overlay with LVDS support

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Kontron Electronics DL i.MX8MM consists of the BL i.MX8MM board
and a 7" LVDS panel. Provide an overlay that enables the panel.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/Makefile        |   4 +
 .../boot/dts/freescale/imx8mm-kontron-dl.dtso | 197 ++++++++++++++++++
 2 files changed, 201 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 300049037eb0b..e08024797721a 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -166,6 +166,10 @@ dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
 
+imx8mm-kontron-dl-dtbs			:= imx8mm-kontron-bl.dtb imx8mm-kontron-dl.dtbo
+
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-dl.dtb
+
 imx8mm-venice-gw72xx-0x-imx219-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-imx219.dtbo
 imx8mm-venice-gw72xx-0x-rpidsi-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rpidsi.dtbo
 imx8mm-venice-gw72xx-0x-rs232-rts-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs232-rts.dtbo
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso b/arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso
new file mode 100644
index 0000000000000..b45c30a68de42
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mm-pinfunc.h"
+
+&{/} {
+	compatible = "kontron,imx8mm-bl", "kontron,imx8mm-sl", "fsl,imx8mm";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000 0>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <100>;
+	};
+
+	panel {
+		compatible = "panel-lvds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel>;
+		backlight = <&backlight>;
+		data-mapping = "vesa-24";
+		enable-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+		height-mm = <86>;
+		width-mm = <154>;
+
+		panel-timing {
+			clock-frequency = <51200000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hsync-len = <1>;
+			hfront-porch = <160>;
+			hback-porch = <160>;
+			vsync-len = <1>;
+			vfront-porch = <12>;
+			vback-porch = <23>;
+		};
+
+		port {
+			panel_out_bridge: endpoint {
+				remote-endpoint = <&bridge_out_panel>;
+			};
+		};
+	};
+};
+
+&dsi_mux_sel {
+	/delete-property/ output-high;
+	output-low;
+};
+
+&dsi_out_bridge {
+	remote-endpoint = <&bridge_in_dsi_lvds>;
+};
+
+&gpio3 {
+	panel_rst {
+		gpio-hog;
+		gpios = <20 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-reset";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_rst>;
+	};
+
+	panel_stby {
+		gpio-hog;
+		gpios = <21 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-standby";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_stby>;
+	};
+
+	panel_hinv {
+		gpio-hog;
+		gpios = <24 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-horizontal-invert";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_hinv>;
+	};
+
+	panel_vinv {
+		gpio-hog;
+		gpios = <25 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "panel-vertical-invert";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_vinv>;
+	};
+};
+
+&hdmi {
+	status = "disabled";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	gt911@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <22 8>;
+		reset-gpios = <&gpio3 23 0>;
+		irq-gpios = <&gpio3 22 0>;
+	};
+};
+
+&lvds {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@2 {
+			reg = <2>;
+			bridge_out_panel: endpoint {
+				remote-endpoint = <&panel_out_bridge>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_panel_rst: panelrstgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x19
+		>;
+	};
+
+	pinctrl_panel_stby: panelstbygrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21		0x19
+		>;
+	};
+
+	pinctrl_panel_hinv: panelhinvgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x19
+		>;
+	};
+
+	pinctrl_panel_vinv: panelvinvgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x40000083
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x40000083
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT		0x6
+		>;
+	};
+
+	pinctrl_panel: panelgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x19
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22		0x19
+			MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x19
+		>;
+	};
+};
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 02/14] arm64: dts: imx8mm-kontron: Add DL (Display-Line) overlay with LVDS support

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The Kontron Electronics DL i.MX8MM consists of the BL i.MX8MM board
and a 7" LVDS panel. Provide an overlay that enables the panel.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/Makefile        |   4 +
 .../boot/dts/freescale/imx8mm-kontron-dl.dtso | 197 ++++++++++++++++++
 2 files changed, 201 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 300049037eb0b..e08024797721a 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -166,6 +166,10 @@ dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
 
+imx8mm-kontron-dl-dtbs			:= imx8mm-kontron-bl.dtb imx8mm-kontron-dl.dtbo
+
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-dl.dtb
+
 imx8mm-venice-gw72xx-0x-imx219-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-imx219.dtbo
 imx8mm-venice-gw72xx-0x-rpidsi-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rpidsi.dtbo
 imx8mm-venice-gw72xx-0x-rs232-rts-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs232-rts.dtbo
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso b/arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso
new file mode 100644
index 0000000000000..b45c30a68de42
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-dl.dtso
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mm-pinfunc.h"
+
+&{/} {
+	compatible = "kontron,imx8mm-bl", "kontron,imx8mm-sl", "fsl,imx8mm";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000 0>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <100>;
+	};
+
+	panel {
+		compatible = "panel-lvds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel>;
+		backlight = <&backlight>;
+		data-mapping = "vesa-24";
+		enable-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+		height-mm = <86>;
+		width-mm = <154>;
+
+		panel-timing {
+			clock-frequency = <51200000>;
+			hactive = <1024>;
+			vactive = <600>;
+			hsync-len = <1>;
+			hfront-porch = <160>;
+			hback-porch = <160>;
+			vsync-len = <1>;
+			vfront-porch = <12>;
+			vback-porch = <23>;
+		};
+
+		port {
+			panel_out_bridge: endpoint {
+				remote-endpoint = <&bridge_out_panel>;
+			};
+		};
+	};
+};
+
+&dsi_mux_sel {
+	/delete-property/ output-high;
+	output-low;
+};
+
+&dsi_out_bridge {
+	remote-endpoint = <&bridge_in_dsi_lvds>;
+};
+
+&gpio3 {
+	panel_rst {
+		gpio-hog;
+		gpios = <20 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-reset";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_rst>;
+	};
+
+	panel_stby {
+		gpio-hog;
+		gpios = <21 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-standby";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_stby>;
+	};
+
+	panel_hinv {
+		gpio-hog;
+		gpios = <24 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "panel-horizontal-invert";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_hinv>;
+	};
+
+	panel_vinv {
+		gpio-hog;
+		gpios = <25 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "panel-vertical-invert";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_vinv>;
+	};
+};
+
+&hdmi {
+	status = "disabled";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	gt911@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <22 8>;
+		reset-gpios = <&gpio3 23 0>;
+		irq-gpios = <&gpio3 22 0>;
+	};
+};
+
+&lvds {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@2 {
+			reg = <2>;
+			bridge_out_panel: endpoint {
+				remote-endpoint = <&panel_out_bridge>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_panel_rst: panelrstgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x19
+		>;
+	};
+
+	pinctrl_panel_stby: panelstbygrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21		0x19
+		>;
+	};
+
+	pinctrl_panel_hinv: panelhinvgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x19
+		>;
+	};
+
+	pinctrl_panel_vinv: panelvinvgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x40000083
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x40000083
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT		0x6
+		>;
+	};
+
+	pinctrl_panel: panelgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x19
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22		0x19
+			MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x19
+		>;
+	};
+};
-- 
2.42.0

[PATCH 03/14] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts | 4 ++--
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi   | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 8b16bd68576c0..0730c22e5b6b9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -294,8 +294,8 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 6e75ab879bf59..3e7db968f7e64 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -252,8 +252,8 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 03/14] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts | 4 ++--
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi   | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 8b16bd68576c0..0730c22e5b6b9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -294,8 +294,8 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 6e75ab879bf59..3e7db968f7e64 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -252,8 +252,8 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
-- 
2.42.0

[PATCH 04/14] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts  | 4 ++--
 arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index f1326bf634a7f..88da7fb71b193 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -421,8 +421,8 @@ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 1f8326613ee9e..2076148e08627 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -237,8 +237,8 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 04/14] arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts  | 4 ++--
 arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index f1326bf634a7f..88da7fb71b193 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -421,8 +421,8 @@ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
 
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 1f8326613ee9e..2076148e08627 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -237,8 +237,8 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
-- 
2.42.0

[PATCH 05/14] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts    | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 0730c22e5b6b9..1dd03ef0a7835 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -313,19 +313,19 @@ MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 05/14] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts    | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 0730c22e5b6b9..1dd03ef0a7835 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -313,19 +313,19 @@ MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
-- 
2.42.0

[PATCH 06/14] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts     | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index 88da7fb71b193..fc096fe739f67 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -441,19 +441,19 @@ MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x19
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 06/14] arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts     | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index 88da7fb71b193..fc096fe739f67 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -441,19 +441,19 @@ MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x19
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 		>;
 	};
 
-- 
2.42.0

[PATCH 07/14] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts  | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 1dd03ef0a7835..d9fa0deea7002 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -337,40 +337,40 @@ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 07/14] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts  | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 1dd03ef0a7835..d9fa0deea7002 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -337,40 +337,40 @@ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };
-- 
2.42.0

[PATCH 08/14] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts   | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index fc096fe739f67..39ca6a65f935b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -465,40 +465,40 @@ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 08/14] arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../boot/dts/freescale/imx8mm-kontron-bl.dts   | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index fc096fe739f67..39ca6a65f935b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -465,40 +465,40 @@ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 
 	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
 			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
 			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
 		>;
 	};
 };
-- 
2.42.0

[PATCH 09/14] arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The level of the interrupt signal is active low instead. Fix this.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 3e7db968f7e64..60abcb636cedf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -210,7 +210,7 @@ rv3028: rtc@52 {
 		reg = <0x52>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc>;
-		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>;
 		trickle-diode-disable;
 	};
 };
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 09/14] arm64: dts: imx8mm-kontron: Fix interrupt for RTC on OSM-S i.MX8MM module

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The level of the interrupt signal is active low instead. Fix this.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 3e7db968f7e64..60abcb636cedf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -210,7 +210,7 @@ rv3028: rtc@52 {
 		reg = <0x52>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc>;
-		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>;
 		trickle-diode-disable;
 	};
 };
-- 
2.42.0

[PATCH 10/14] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The current state of the devicetree for the i.MX8MM OSM-S and the BL
baseboard reflects deprecated prototype hardware. Update the board
description to match the latest hardware revision.

As the old hardware is not available anymore, was only produced in
very small quantities and was broken in some ways, we can safely
fixup the original devicetree.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 64 ++++++++++++-------
 1 file changed, 41 insertions(+), 23 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index d9fa0deea7002..7c5586efccc59 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -30,18 +30,18 @@ leds {
 
 		led1 {
 			label = "led1";
-			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		led2 {
 			label = "led2";
-			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
 		};
 
 		led3 {
 			label = "led3";
-			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -54,7 +54,7 @@ reg_rst_eth2: regulator-rst-eth2 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usb_eth2>;
-		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
 		regulator-name = "rst-usb-eth2";
@@ -91,7 +91,7 @@ can@0 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_can>;
 		clocks = <&osc_can>;
-		interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>;
 		/*
 		 * Limit the SPI clock to 15 MHz to prevent issues
 		 * with corrupted data due to chip errata.
@@ -118,7 +118,7 @@ eeram@0 {
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii-rxid";
+	phy-connection-type = "rgmii-id";
 	phy-handle = <&ethphy>;
 	status = "okay";
 
@@ -127,10 +127,11 @@ mdio {
 		#size-cells = <0>;
 
 		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-id4f51.e91b",
+				     "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
-			reset-assert-us = <1>;
-			reset-deassert-us = <15000>;
-			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -153,11 +154,24 @@ &gpio5 {
 			  "", "", "", "", "", "", "", "";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	usb-hub@2c {
+		compatible = "microchip,usb2514b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_hub>;
+		reg = <0x2c>;
+		non-removable-ports = <0>, <3>;
+		reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
 &i2c4 {
-	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c4>;
-	status = "okay";
 };
 
 &pwm2 {
@@ -196,13 +210,13 @@ &usbotg2 {
 	status = "okay";
 
 	usb1@1 {
-		compatible = "usb424,9514";
+		compatible = "usb424,2514";
 		reg = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		usbnet: ethernet@1 {
-			compatible = "usb424,ec00";
+			compatible = "usbb95,772b";
 			reg = <1>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
 		};
@@ -223,7 +237,7 @@ &usdhc2 {
 &iomuxc {
 	pinctrl_can: cangrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19
 		>;
 	};
 
@@ -261,27 +275,24 @@ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
 			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
 			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
-			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19 /* PHY RST */
-			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19 /* ETH IRQ */
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19 /* PHY RST */
 		>;
 	};
 
 	pinctrl_gpio_led: gpioledgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x19
-			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x19
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
 		>;
 	};
 
 	pinctrl_gpio1: gpio1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
-			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
 			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
 			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
 			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
-			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
 			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
 		>;
 	};
@@ -292,6 +303,13 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
@@ -331,7 +349,7 @@ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 
 	pinctrl_usb_eth2: usbeth2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
 		>;
 	};
 
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 10/14] arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The current state of the devicetree for the i.MX8MM OSM-S and the BL
baseboard reflects deprecated prototype hardware. Update the board
description to match the latest hardware revision.

As the old hardware is not available anymore, was only produced in
very small quantities and was broken in some ways, we can safely
fixup the original devicetree.

Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 64 ++++++++++++-------
 1 file changed, 41 insertions(+), 23 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index d9fa0deea7002..7c5586efccc59 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -30,18 +30,18 @@ leds {
 
 		led1 {
 			label = "led1";
-			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		led2 {
 			label = "led2";
-			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
 		};
 
 		led3 {
 			label = "led3";
-			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -54,7 +54,7 @@ reg_rst_eth2: regulator-rst-eth2 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usb_eth2>;
-		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
 		regulator-name = "rst-usb-eth2";
@@ -91,7 +91,7 @@ can@0 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_can>;
 		clocks = <&osc_can>;
-		interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>;
 		/*
 		 * Limit the SPI clock to 15 MHz to prevent issues
 		 * with corrupted data due to chip errata.
@@ -118,7 +118,7 @@ eeram@0 {
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii-rxid";
+	phy-connection-type = "rgmii-id";
 	phy-handle = <&ethphy>;
 	status = "okay";
 
@@ -127,10 +127,11 @@ mdio {
 		#size-cells = <0>;
 
 		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-id4f51.e91b",
+				     "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
-			reset-assert-us = <1>;
-			reset-deassert-us = <15000>;
-			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -153,11 +154,24 @@ &gpio5 {
 			  "", "", "", "", "", "", "", "";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	usb-hub@2c {
+		compatible = "microchip,usb2514b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_hub>;
+		reg = <0x2c>;
+		non-removable-ports = <0>, <3>;
+		reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
 &i2c4 {
-	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c4>;
-	status = "okay";
 };
 
 &pwm2 {
@@ -196,13 +210,13 @@ &usbotg2 {
 	status = "okay";
 
 	usb1@1 {
-		compatible = "usb424,9514";
+		compatible = "usb424,2514";
 		reg = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		usbnet: ethernet@1 {
-			compatible = "usb424,ec00";
+			compatible = "usbb95,772b";
 			reg = <1>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
 		};
@@ -223,7 +237,7 @@ &usdhc2 {
 &iomuxc {
 	pinctrl_can: cangrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19
 		>;
 	};
 
@@ -261,27 +275,24 @@ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
 			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
 			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
 			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
-			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19 /* PHY RST */
-			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19 /* ETH IRQ */
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19 /* PHY RST */
 		>;
 	};
 
 	pinctrl_gpio_led: gpioledgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x19
-			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x19
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
 		>;
 	};
 
 	pinctrl_gpio1: gpio1grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
-			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
 			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
 			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
 			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
-			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
 			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
 		>;
 	};
@@ -292,6 +303,13 @@ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
 		>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
@@ -331,7 +349,7 @@ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
 
 	pinctrl_usb_eth2: usbeth2grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
 		>;
 	};
 
-- 
2.42.0

[PATCH 11/14] arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The PUE bit is only effective if the PE bit is also set. To avoid
confusion, disable the PUE bit if it is not needed.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 7c5586efccc59..12f786a72fbd5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -362,7 +362,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
 		>;
 	};
 
@@ -375,7 +375,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
 		>;
 	};
 
@@ -388,7 +388,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
 		>;
 	};
 };
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 11/14] arm64: dts: imx8mm-kontron: Disable uneffective PUE bit in SDIO IOMUX

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The PUE bit is only effective if the PE bit is also set. To avoid
confusion, disable the PUE bit if it is not needed.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 7c5586efccc59..12f786a72fbd5 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -362,7 +362,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
 		>;
 	};
 
@@ -375,7 +375,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
 		>;
 	};
 
@@ -388,7 +388,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
 			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
 			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0xd0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
 		>;
 	};
 };
-- 
2.42.0

[PATCH 12/14] arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The RV3028 driver doesn't use this property. Remove it.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 60abcb636cedf..b161b0c85d61e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -211,7 +211,6 @@ rv3028: rtc@52 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc>;
 		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>;
-		trickle-diode-disable;
 	};
 };
 
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 12/14] arm64: dts: imx8mm-kontron: Remove useless trickle-diode-disable from RTC node

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The RV3028 driver doesn't use this property. Remove it.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 60abcb636cedf..b161b0c85d61e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -211,7 +211,6 @@ rv3028: rtc@52 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc>;
 		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_LOW>;
-		trickle-diode-disable;
 	};
 };
 
-- 
2.42.0

[PATCH 13/14] arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

There is an EEPROM on the SoM module. Add it to the description.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index b161b0c85d61e..6b9058fc53332 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -205,6 +205,14 @@ reg_nvcc_sd: LDO5 {
 		};
 	};
 
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		address-width = <16>;
+		pagesize = <32>;
+		size = <8192>;
+	};
+
 	rv3028: rtc@52 {
 		compatible = "microcrystal,rv3028";
 		reg = <0x52>;
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 13/14] arm64: dts: imx8mm-kontron: Add I2C EEPROM on OSM-S Kontron i.MX8MM

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

There is an EEPROM on the SoM module. Add it to the description.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index b161b0c85d61e..6b9058fc53332 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -205,6 +205,14 @@ reg_nvcc_sd: LDO5 {
 		};
 	};
 
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		address-width = <16>;
+		pagesize = <32>;
+		size = <8192>;
+	};
+
 	rv3028: rtc@52 {
 		compatible = "microcrystal,rv3028";
 		reg = <0x52>;
-- 
2.42.0

[PATCH 14/14] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The OSM spec defines dedicated functions for all pads of the SoM.
Therefore we can assume that carrier board designs stick to these
definitions and extend the SoM devicetree include with matching
default nodes and pinmux settings.

This way we can reduce the overhead and redundancy in the carrier
board devicetrees while still sticking to the policy of separating
board and module description.

Even if the carrier board design deviates slightly from the spec it
can define its own pinmux definitions and use them as necessary or
even disable unused nodes from the SoM devicetree.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 269 +++------
 .../dts/freescale/imx8mm-kontron-osm-s.dtsi   | 552 +++++++++++++++++-
 2 files changed, 616 insertions(+), 205 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 12f786a72fbd5..efadfdff00af1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -25,8 +25,6 @@ osc_can: clock-osc-can {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_led>;
 
 		led1 {
 			label = "led1";
@@ -52,24 +50,12 @@ pwm-beeper {
 
 	reg_rst_eth2: regulator-rst-eth2 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb_eth2>;
 		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
 		regulator-name = "rst-usb-eth2";
 	};
 
-	reg_usb1_vbus: regulator-usb1-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
-		gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-name = "usb1-vbus";
-	};
-
 	reg_vdd_5v: regulator-5v {
 		compatible = "regulator-fixed";
 		regulator-always-on;
@@ -80,9 +66,6 @@ reg_vdd_5v: regulator-5v {
 };
 
 &ecspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	can@0 {
@@ -103,9 +86,6 @@ can@0 {
 };
 
 &ecspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3>;
-	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeram@0 {
@@ -117,7 +97,7 @@ eeram@0 {
 
 &fec1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
+	pinctrl-0 = <&pinctrl_enet_rgmii>;
 	phy-connection-type = "rgmii-id";
 	phy-handle = <&ethphy>;
 	status = "okay";
@@ -136,27 +116,59 @@ ethphy: ethernet-phy@0 {
 	};
 };
 
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_0      -> DIO1_OUT
+ *   GPIO_B_1      -> DIO2_OUT
+ */
 &gpio1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1>;
-	gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
-			  "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
-			  "", "", "", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "";
+	gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
+			  "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+			  "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "DIO1_OUT",
+			  "DIO2_OUT", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
+			  "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
+			  "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
+			  "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
+			  "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
+			  "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
+			  "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
+			  "ETH_A_(R)(G)MII_RXD3";
 };
 
-&gpio5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio5>;
-	gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "";
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_2      -> DIO3_OUT
+ *   GPIO_B_3      -> DIO4_OUT
+ */
+&gpio3 {
+	gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
+			  "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
+			  "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
+			  "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "DIO3_OUT",
+			  "USB_B_EN", "DIO4_OUT", "PCIe_CLKREQ#", "PCIe_A_PERST#",
+			  "PCIe_WAKE#", "USB_A_EN";
+};
+
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_4      -> DIO1_IN
+ *   GPIO_B_5      -> DIO2_IN
+ *   GPIO_B_6      -> DIO3_IN
+ *   GPIO_B_7      -> DIO4_IN
+ */
+&gpio4 {
+	gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
+			  "DIO1_IN", "BOOT_SEL0#", "BOOT_SEL1#", "",
+			  "", "", "I2S_LRCLK", "I2S_BITCLK",
+			  "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "DIO2_IN", "DIO3_IN",
+			  "DIO4_IN", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
+			  "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
+			  "UART_A_RTS", "", "", "",
+			  "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
 };
 
 &i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
 	usb-hub@2c {
@@ -169,27 +181,28 @@ usb-hub@2c {
 	};
 };
 
-&i2c4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c4>;
-};
-
 &pwm2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
 };
 
+&reg_usb2_vbus {
+	status = "disabled";
+};
+
+&reg_usdhc2_vcc {
+	status = "disabled";
+};
+
+&reg_usdhc3_vcc {
+	status = "disabled";
+};
+
 &uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
 	uart-has-rtscts;
 	status = "okay";
 };
 
 &uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
 	linux,rs485-enabled-at-boot-time;
 	uart-has-rtscts;
 	status = "okay";
@@ -197,8 +210,6 @@ &uart2 {
 
 &usbotg1 {
 	dr_mode = "otg";
-	disable-over-current;
-	vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
 };
 
@@ -209,6 +220,9 @@ &usbotg2 {
 	#size-cells = <0>;
 	status = "okay";
 
+	/* VBUS is controlled by the hub */
+	/delete-property/ vbus-supply;
+
 	usb1@1 {
 		compatible = "usb424,2514";
 		reg = <1>;
@@ -224,171 +238,20 @@ usbnet: ethernet@1 {
 };
 
 &usdhc2 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
-	vqmmc-supply = <&reg_nvcc_sd>;
-	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &iomuxc {
 	pinctrl_can: cangrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19
-		>;
-	};
-
-	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
-			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
-		>;
-	};
-
-	pinctrl_ecspi3: ecspi3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
-			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
-			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
-			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
-		>;
-	};
-
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
-			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
-			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
-			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
-			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
-			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
-			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
-			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
-			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
-			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
-			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
-			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
-			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
-			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
-			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19 /* PHY RST */
-		>;
-	};
-
-	pinctrl_gpio_led: gpioledgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19
-			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
-			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
-		>;
-	};
-
-	pinctrl_gpio1: gpio1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
-			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
-			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
-			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
-			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
-		>;
-	};
-
-	pinctrl_gpio5: gpio5grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
-		>;
-	};
-
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
-			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
-		>;
-	};
-
-	pinctrl_i2c4: i2c4grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
-		>;
-	};
-
-	pinctrl_pwm2: pwm2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
-		>;
-	};
-
-	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
-		>;
-	};
-
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
-		>;
-	};
-
-	pinctrl_usb_eth2: usbeth2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
-		>;
-	};
-
-	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19  /* SDIO_B_PWR_EN */
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+	pinctrl_usb_hub: usbhubgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19 /* SDIO_B_WP */
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 6b9058fc53332..1a5c29565e7fe 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -3,6 +3,7 @@
  * Copyright (C) 2022 Kontron Electronics GmbH
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "imx8mm.dtsi"
 
@@ -28,6 +29,73 @@ memory@40000000 {
 	chosen {
 		stdout-path = &uart3;
 	};
+
+	reg_vdd_carrier: regulator-vdd-carrier {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
+		enable-active-high;
+		gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "VDD_CARRIER";
+
+		regulator-state-standby {
+			regulator-on-in-suspend;
+		};
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+
+		regulator-state-disk {
+			regulator-off-in-suspend;
+		};
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+		enable-active-high;
+		gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "VBUS_USB1";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_vbus>;
+		enable-active-high;
+		gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "VBUS_USB2";
+	};
+
+	reg_usdhc2_vcc: regulator-usdhc2-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
+		enable-active-high;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_A";
+	};
+
+	reg_usdhc3_vcc: regulator-usdhc3-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc3_vcc>;
+		enable-active-high;
+		gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_B";
+	};
 };
 
 &A53_0 {
@@ -96,6 +164,79 @@ partition@1f0000 {
 	};
 };
 
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>, <&pinctrl_ecspi2_gpio>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+	gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
+			  "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+			  "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "GPIO_B_0",
+			  "GPIO_B_1", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
+			  "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
+			  "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
+			  "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
+			  "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
+			  "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
+			  "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
+			  "ETH_A_(R)(G)MII_RXD3";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SDIO_A_CD#", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
+			  "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN",
+			  "SDIO_A_WP";
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio3>;
+	gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
+			  "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
+			  "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
+			  "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "GPIO_B_2",
+			  "USB_B_EN", "GPIO_B_3", "PCIe_CLKREQ#", "PCIe_A_PERST#",
+			  "PCIe_WAKE#", "USB_A_EN";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+	gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
+			  "GPIO_B_4", "BOOT_SEL0#", "BOOT_SEL1#", "",
+			  "", "", "I2S_LRCLK", "I2S_BITCLK",
+			  "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "GPIO_B_5", "GPIO_B_6",
+			  "GPIO_B_7", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
+			  "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
+			  "UART_A_RTS", "", "", "",
+			  "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
+};
+
+&gpio5 {
+	gpio-line-names = "UART_B_TX", "SDIO_B_PWR_EN", "SDIO_B_WP", "PWM_2",
+			  "PWM_1", "PWM_0", "", "",
+			  "", "", "SPI_A_SCK", "SPI_A_SDO_(IO1)",
+			  "SPI_A_SCK", "SPI_A_CS0#", "", "",
+			  "I2C_A_SCL", "I2C_A_SDA", "I2C_B_SCL", "I2C_B_SDA",
+			  "PCIe_SMCLK", "PCIe_SMDAT", "SPI_B_SCK", "SPI_B_SDO",
+			  "SPI_B_SDI", "SPI_B_CS0#", "UART_CON_RX", "UART_CON_TX",
+			  "UART_C_RX", "UART_C_TX";
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -222,12 +363,69 @@ rv3028: rtc@52 {
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+};
+
 &uart3 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 };
 
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1>;
+	vbus-supply = <&reg_usb1_vbus>;
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb2>;
+	vbus-supply = <&reg_usb2_vbus>;
+};
+
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -240,6 +438,26 @@ &usdhc1 {
 	status = "okay";
 };
 
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	vmmc-supply = <&reg_usdhc2_vcc>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+	vmmc-supply = <&reg_usdhc3_vcc>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
@@ -248,6 +466,12 @@ &wdog1 {
 };
 
 &iomuxc {
+	pinctrl_csi_mck: csimckgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1	0x59 /* CAM_MCK */
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
@@ -257,6 +481,106 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
 		>;
 	};
 
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82 /* SPI_A_SDI_(IO0) */
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82 /* SPI_A_SDO_(IO1) */
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82 /* SPI_A_SCK */
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19 /* SPI_A_CS0# */
+		>;
+	};
+
+	pinctrl_ecspi2_gpio: ecspi2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x19 /* SPI_A_/WP_(IO2) */
+			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x19 /* SPI_A_/HOLD_(IO3) */
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82 /* SPI_B_SDI */
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82 /* SPI_B_SDO */
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82 /* SPI_B_SCK */
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19 /* SPI_B_CS0# */
+		>;
+	};
+
+	pinctrl_enet_rgmii: enetrgmiigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x03 /* ETH_MDC */
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x03 /* ETH_MDIO */
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f /* ETH_A_(S)(R)(G)MII_TXD3 */
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f /* ETH_A_(S)(R)(G)MII_TXD2 */
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f /* ETH_A_(S)(R)(G)MII_TXD1 */
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f /* ETH_A_(S)(R)(G)MII_TXD0 */
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91 /* ETH_A_(R)(G)MII_RXD3 */
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91 /* ETH_A_(R)(G)MII_RXD2 */
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91 /* ETH_A_(S)(R)(G)MII_RXD1 */
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91 /* ETH_A_(S)(R)(G)MII_RXD0 */
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f /* ETH_A_(R)(G)MII_TX_CLK */
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91 /* ETH_A_(R)(G)MII_RX_CLK */
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+		>;
+	};
+
+	pinctrl_enet_rmii: enetrmiigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x03 /* ETH_MDC */
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x03 /* ETH_MDIO */
+			MX8MM_IOMUXC_ENET_TD2_ENET1_TX_CLK		0x4000001f /* ETH_A_(S)(R)(G)MII_TXD2 */
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x56 /* ETH_A_(S)(R)(G)MII_TXD1 */
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x56 /* ETH_A_(S)(R)(G)MII_TXD0 */
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x56 /* ETH_A_(S)(R)(G)MII_RXD1 */
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x56 /* ETH_A_(S)(R)(G)MII_RXD0 */
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RX_ER		0x56 /* ETH_A_(R)(G)MII_RX_CLK */
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x56 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x56 /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19 /* GPIO_A_0 */
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19 /* GPIO_A_1 */
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19 /* GPIO_A_2 */
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19 /* GPIO_A_3 */
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19 /* GPIO_A_4 */
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19 /* GPIO_A_5 */
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19 /* GPIO_A_6 */
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19 /* GPIO_A_7 */
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19 /* GPIO_B_0 */
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x19 /* GPIO_B_1 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0			0x19 /* GPIO_C_5 */
+			MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1		0x19 /* GPIO_C_4 */
+			MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6		0x19 /* GPIO_C_0 */
+			MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7		0x19 /* GPIO_C_1 */
+			MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8		0x19 /* GPIO_C_2 */
+			MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9		0x19 /* GPIO_C_3 */
+			MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x19 /* GPIO_B_2 */
+			MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21		0x19 /* GPIO_B_3 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0		0x19 /* GPIO_C_7 */
+			MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4		0x19 /* GPIO_B_4 */
+			MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5		0x19 /* BOOT_SEL0# */
+			MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6		0x19 /* BOOT_SEL1# */
+			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x19 /* GPIO_B_5 */
+			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x19 /* GPIO_B_6 */
+			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x19 /* GPIO_B_7 */
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x19 /* GPIO_C_6 */
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
@@ -264,22 +588,149 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x40000083 /* I2C_A_SCL */
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x40000083 /* I2C_A_SDA */
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083 /* I2C_B_SCL */
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083 /* I2C_B_SDA */
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083 /* PCIe_SMCLK and I2C_CAM_SCL/CSI_TX_P */
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083 /* PCIe_SMDAT and I2C_CAM_SDA/CSI_TX_N */
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22		0x19 /* PCIe_CLKREQ# */
+			MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x19 /* PCIe_A_PERST# */
+			MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x19 /* PCIe_WAKE# */
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19 /* PCIe_SM_ALERT */
+		>;
+	};
+
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
 		>;
 	};
 
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT		0x19 /* PWM_0 */
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19 /* PWM_1 */
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT			0x19 /* PWM_2 */
+		>;
+	};
+
+	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19 /* USB_A_EN */
+		>;
+	};
+
+	pinctrl_reg_usb2_vbus: regusb2vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x19 /* USB_B_EN */
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x19 /* SDIO_A_PWR_EN */
+		>;
+	};
+
+	pinctrl_reg_usdhc3_vcc: regusdhc3vccgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19 /* SDIO_B_PWR_EN */
+		>;
+	};
+
+	pinctrl_reg_vdd_carrier: regvddcarriergrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x19 /* CARRIER_PWR_EN */
+		>;
+	};
+
 	pinctrl_rtc: rtcgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1			0x19
 		>;
 	};
 
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0		0xd6 /* I2S_A_DATA_IN */
+			MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0		0xd6 /* I2S_A_DATA_OUT */
+			MX8MM_IOMUXC_SAI1_RXD1_SAI1_RX_DATA1		0xd6 /* I2S_B_DATA_IN */
+			MX8MM_IOMUXC_SAI1_TXD1_SAI1_TX_DATA1		0xd6 /* I2S_B_DATA_OUT */
+			MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK		0xd6 /* I2S_MCLK */
+			MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC		0xd6 /* I2S_LRCLK */
+			MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK		0xd6 /* I2S_BITCLK */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0 /* UART_A_RX */
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0 /* UART_A_TX */
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0 /* UART_A_CTS */
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0 /* UART_A_RTS */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0 /* UART_B_RX */
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0 /* UART_B_TX */
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0 /* UART_B_CTS */
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0 /* UART_B_RTS */
+		>;
+	};
+
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
-			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140 /* UART_CON_RX */
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140 /* UART_CON_TX */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x0 /* UART_C_RX */
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x0 /* UART_C_TX */
+		>;
+	};
+
+	pinctrl_usb1: usb1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x19 /* USB_A_OC# */
+		>;
+	};
+
+	pinctrl_usb2: usb2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC		0x19 /* USB_B_OC# */
 		>;
 	};
 
@@ -334,6 +785,103 @@ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
 		>;
 	};
 
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90 /* SDIO_A_CLK */
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0 /* SDIO_A_CMD */
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0 /* SDIO_A_D0 */
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0 /* SDIO_A_D1 */
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0 /* SDIO_A_D2 */
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0 /* SDIO_A_D3 */
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94 /* SDIO_A_CLK */
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4 /* SDIO_A_CMD */
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4 /* SDIO_A_D0 */
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4 /* SDIO_A_D1 */
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4 /* SDIO_A_D2 */
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4 /* SDIO_A_D3 */
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96 /* SDIO_A_CLK */
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6 /* SDIO_A_CMD */
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6 /* SDIO_A_D0 */
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6 /* SDIO_A_D1 */
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6 /* SDIO_A_D2 */
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6 /* SDIO_A_D3 */
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19 /* SDIO_A_CD# */
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x90 /* SDIO_B_CLK */
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x90 /* SDIO_B_CMD */
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x90 /* SDIO_B_D0 */
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x90 /* SDIO_B_D1 */
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x90 /* SDIO_B_D2 */
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x90 /* SDIO_B_D3 */
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x90 /* SDIO_B_D4 */
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x90 /* SDIO_B_D5 */
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x90 /* SDIO_B_D6 */
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x90 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x94 /* SDIO_B_CLK */
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x94 /* SDIO_B_CMD */
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x94 /* SDIO_B_D0 */
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x94 /* SDIO_B_D1 */
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x94 /* SDIO_B_D2 */
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x94 /* SDIO_B_D3 */
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x94 /* SDIO_B_D4 */
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x94 /* SDIO_B_D5 */
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x94 /* SDIO_B_D6 */
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x94 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x96 /* SDIO_B_CLK */
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x96 /* SDIO_B_CMD */
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x96 /* SDIO_B_D0 */
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x96 /* SDIO_B_D1 */
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x96 /* SDIO_B_D2 */
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x96 /* SDIO_B_D3 */
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x96 /* SDIO_B_D4 */
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x96 /* SDIO_B_D5 */
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x96 /* SDIO_B_D6 */
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x96 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_gpio: usdhc3gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19 /* SDIO_B_CD# */
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19 /* SDIO_B_WP */
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
-- 
2.42.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 14/14] arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The OSM spec defines dedicated functions for all pads of the SoM.
Therefore we can assume that carrier board designs stick to these
definitions and extend the SoM devicetree include with matching
default nodes and pinmux settings.

This way we can reduce the overhead and redundancy in the carrier
board devicetrees while still sticking to the policy of separating
board and module description.

Even if the carrier board design deviates slightly from the spec it
can define its own pinmux definitions and use them as necessary or
even disable unused nodes from the SoM devicetree.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
 .../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 269 +++------
 .../dts/freescale/imx8mm-kontron-osm-s.dtsi   | 552 +++++++++++++++++-
 2 files changed, 616 insertions(+), 205 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
index 12f786a72fbd5..efadfdff00af1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -25,8 +25,6 @@ osc_can: clock-osc-can {
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_led>;
 
 		led1 {
 			label = "led1";
@@ -52,24 +50,12 @@ pwm-beeper {
 
 	reg_rst_eth2: regulator-rst-eth2 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb_eth2>;
 		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
 		regulator-name = "rst-usb-eth2";
 	};
 
-	reg_usb1_vbus: regulator-usb1-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
-		gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-name = "usb1-vbus";
-	};
-
 	reg_vdd_5v: regulator-5v {
 		compatible = "regulator-fixed";
 		regulator-always-on;
@@ -80,9 +66,6 @@ reg_vdd_5v: regulator-5v {
 };
 
 &ecspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	can@0 {
@@ -103,9 +86,6 @@ can@0 {
 };
 
 &ecspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3>;
-	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeram@0 {
@@ -117,7 +97,7 @@ eeram@0 {
 
 &fec1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
+	pinctrl-0 = <&pinctrl_enet_rgmii>;
 	phy-connection-type = "rgmii-id";
 	phy-handle = <&ethphy>;
 	status = "okay";
@@ -136,27 +116,59 @@ ethphy: ethernet-phy@0 {
 	};
 };
 
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_0      -> DIO1_OUT
+ *   GPIO_B_1      -> DIO2_OUT
+ */
 &gpio1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1>;
-	gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
-			  "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
-			  "", "", "", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "";
+	gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
+			  "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+			  "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "DIO1_OUT",
+			  "DIO2_OUT", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
+			  "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
+			  "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
+			  "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
+			  "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
+			  "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
+			  "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
+			  "ETH_A_(R)(G)MII_RXD3";
 };
 
-&gpio5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio5>;
-	gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "",
-			  "", "", "", "", "", "", "", "";
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_2      -> DIO3_OUT
+ *   GPIO_B_3      -> DIO4_OUT
+ */
+&gpio3 {
+	gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
+			  "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
+			  "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
+			  "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "DIO3_OUT",
+			  "USB_B_EN", "DIO4_OUT", "PCIe_CLKREQ#", "PCIe_A_PERST#",
+			  "PCIe_WAKE#", "USB_A_EN";
+};
+
+/*
+ * Rename SoM signals according to board usage:
+ *   GPIO_B_4      -> DIO1_IN
+ *   GPIO_B_5      -> DIO2_IN
+ *   GPIO_B_6      -> DIO3_IN
+ *   GPIO_B_7      -> DIO4_IN
+ */
+&gpio4 {
+	gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
+			  "DIO1_IN", "BOOT_SEL0#", "BOOT_SEL1#", "",
+			  "", "", "I2S_LRCLK", "I2S_BITCLK",
+			  "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "DIO2_IN", "DIO3_IN",
+			  "DIO4_IN", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
+			  "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
+			  "UART_A_RTS", "", "", "",
+			  "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
 };
 
 &i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
 	usb-hub@2c {
@@ -169,27 +181,28 @@ usb-hub@2c {
 	};
 };
 
-&i2c4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c4>;
-};
-
 &pwm2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
 };
 
+&reg_usb2_vbus {
+	status = "disabled";
+};
+
+&reg_usdhc2_vcc {
+	status = "disabled";
+};
+
+&reg_usdhc3_vcc {
+	status = "disabled";
+};
+
 &uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
 	uart-has-rtscts;
 	status = "okay";
 };
 
 &uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
 	linux,rs485-enabled-at-boot-time;
 	uart-has-rtscts;
 	status = "okay";
@@ -197,8 +210,6 @@ &uart2 {
 
 &usbotg1 {
 	dr_mode = "otg";
-	disable-over-current;
-	vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
 };
 
@@ -209,6 +220,9 @@ &usbotg2 {
 	#size-cells = <0>;
 	status = "okay";
 
+	/* VBUS is controlled by the hub */
+	/delete-property/ vbus-supply;
+
 	usb1@1 {
 		compatible = "usb424,2514";
 		reg = <1>;
@@ -224,171 +238,20 @@ usbnet: ethernet@1 {
 };
 
 &usdhc2 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
-	vqmmc-supply = <&reg_nvcc_sd>;
-	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &iomuxc {
 	pinctrl_can: cangrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19
-		>;
-	};
-
-	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
-			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
-		>;
-	};
-
-	pinctrl_ecspi3: ecspi3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
-			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
-			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
-			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
-		>;
-	};
-
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
-			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
-			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
-			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
-			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
-			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
-			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
-			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
-			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
-			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
-			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
-			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
-			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
-			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
-			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19 /* PHY RST */
-		>;
-	};
-
-	pinctrl_gpio_led: gpioledgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19
-			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
-			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
-		>;
-	};
-
-	pinctrl_gpio1: gpio1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
-			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
-			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
-			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
-			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
-		>;
-	};
-
-	pinctrl_gpio5: gpio5grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
-		>;
-	};
-
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083
-			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083
-		>;
-	};
-
-	pinctrl_i2c4: i2c4grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083
-		>;
-	};
-
-	pinctrl_pwm2: pwm2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
-		>;
-	};
-
-	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
-		>;
-	};
-
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0
-		>;
-	};
-
-	pinctrl_usb_eth2: usbeth2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
-		>;
-	};
-
-	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19  /* SDIO_B_PWR_EN */
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+	pinctrl_usb_hub: usbhubgrp {
 		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19
-			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19 /* SDIO_B_WP */
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
index 6b9058fc53332..1a5c29565e7fe 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -3,6 +3,7 @@
  * Copyright (C) 2022 Kontron Electronics GmbH
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "imx8mm.dtsi"
 
@@ -28,6 +29,73 @@ memory@40000000 {
 	chosen {
 		stdout-path = &uart3;
 	};
+
+	reg_vdd_carrier: regulator-vdd-carrier {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_vdd_carrier>;
+		enable-active-high;
+		gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "VDD_CARRIER";
+
+		regulator-state-standby {
+			regulator-on-in-suspend;
+		};
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+
+		regulator-state-disk {
+			regulator-off-in-suspend;
+		};
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+		enable-active-high;
+		gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "VBUS_USB1";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_vbus>;
+		enable-active-high;
+		gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "VBUS_USB2";
+	};
+
+	reg_usdhc2_vcc: regulator-usdhc2-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vcc>;
+		enable-active-high;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_A";
+	};
+
+	reg_usdhc3_vcc: regulator-usdhc3-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc3_vcc>;
+		enable-active-high;
+		gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "VCC_SDIO_B";
+	};
 };
 
 &A53_0 {
@@ -96,6 +164,79 @@ partition@1f0000 {
 	};
 };
 
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>, <&pinctrl_ecspi2_gpio>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+	gpio-line-names = "", "GPIO_A_0", "", "GPIO_A_1",
+			  "", "GPIO_A_2", "GPIO_A_3", "GPIO_A_4",
+			  "GPIO_A_5", "GPIO_A_6", "GPIO_A_7", "GPIO_B_0",
+			  "GPIO_B_1", "USB_A_OC#", "CAM_MCK", "USB_B_OC#",
+			  "ETH_MDC", "ETH_MDIO", "ETH_A_(S)(R)(G)MII_TXD3",
+			  "ETH_A_(S)(R)(G)MII_TXD2", "ETH_A_(S)(R)(G)MII_TXD1",
+			  "ETH_A_(S)(R)(G)MII_TXD0", "ETH_A_(R)(G)MII_TX_EN(_ER)",
+			  "ETH_A_(R)(G)MII_TX_CLK", "ETH_A_(R)(G)MII_RX_DV(_ER)",
+			  "ETH_A_(R)(G)MII_RX_CLK", "ETH_A_(S)(R)(G)MII_RXD0",
+			  "ETH_A_(S)(R)(G)MII_RXD1", "ETH_A_(R)(G)MII_RXD2",
+			  "ETH_A_(R)(G)MII_RXD3";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SDIO_A_CD#", "SDIO_A_CLK", "SDIO_A_CMD", "SDIO_A_D0",
+			  "SDIO_A_D1", "SDIO_A_D2", "SDIO_A_D3", "SDIO_A_PWR_EN",
+			  "SDIO_A_WP";
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio3>;
+	gpio-line-names = "GPIO_C_5", "GPIO_C_4", "SDIO_B_CD#", "SDIO_B_D5",
+			  "SDIO_B_D6", "SDIO_B_D7", "GPIO_C_0", "GPIO_C_1",
+			  "GPIO_C_2", "GPIO_C_3", "SDIO_B_D0", "SDIO_B_D1",
+			  "SDIO_B_D2", "SDIO_B_D3", "", "SDIO_B_D4",
+			  "CARRIER_PWR_EN", "SDIO_B_CLK", "SDIO_B_CMD", "GPIO_B_2",
+			  "USB_B_EN", "GPIO_B_3", "PCIe_CLKREQ#", "PCIe_A_PERST#",
+			  "PCIe_WAKE#", "USB_A_EN";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+	gpio-line-names = "GPIO_C_7", "", "I2S_A_DATA_IN", "I2S_B_DATA_IN",
+			  "GPIO_B_4", "BOOT_SEL0#", "BOOT_SEL1#", "",
+			  "", "", "I2S_LRCLK", "I2S_BITCLK",
+			  "I2S_A_DATA_OUT", "I2S_B_DATA_OUT", "GPIO_B_5", "GPIO_B_6",
+			  "GPIO_B_7", "SPI_A_/WP_(IO2)", "SPI_A_/HOLD_(IO3)", "GPIO_C_6",
+			  "I2S_MCLK", "UART_A_TX", "UART_A_RX", "UART_A_CTS",
+			  "UART_A_RTS", "", "", "",
+			  "PCIe_SM_ALERT", "UART_B_RTS", "UART_B_CTS", "UART_B_RX";
+};
+
+&gpio5 {
+	gpio-line-names = "UART_B_TX", "SDIO_B_PWR_EN", "SDIO_B_WP", "PWM_2",
+			  "PWM_1", "PWM_0", "", "",
+			  "", "", "SPI_A_SCK", "SPI_A_SDO_(IO1)",
+			  "SPI_A_SCK", "SPI_A_CS0#", "", "",
+			  "I2C_A_SCL", "I2C_A_SDA", "I2C_B_SCL", "I2C_B_SDA",
+			  "PCIe_SMCLK", "PCIe_SMDAT", "SPI_B_SCK", "SPI_B_SDO",
+			  "SPI_B_SDI", "SPI_B_CS0#", "UART_CON_RX", "UART_CON_TX",
+			  "UART_C_RX", "UART_C_TX";
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -222,12 +363,69 @@ rv3028: rtc@52 {
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+};
+
 &uart3 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 };
 
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1>;
+	vbus-supply = <&reg_usb1_vbus>;
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb2>;
+	vbus-supply = <&reg_usb2_vbus>;
+};
+
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -240,6 +438,26 @@ &usdhc1 {
 	status = "okay";
 };
 
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	vmmc-supply = <&reg_usdhc2_vcc>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+	vmmc-supply = <&reg_usdhc3_vcc>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
@@ -248,6 +466,12 @@ &wdog1 {
 };
 
 &iomuxc {
+	pinctrl_csi_mck: csimckgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1	0x59 /* CAM_MCK */
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
@@ -257,6 +481,106 @@ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
 		>;
 	};
 
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82 /* SPI_A_SDI_(IO0) */
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82 /* SPI_A_SDO_(IO1) */
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82 /* SPI_A_SCK */
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19 /* SPI_A_CS0# */
+		>;
+	};
+
+	pinctrl_ecspi2_gpio: ecspi2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x19 /* SPI_A_/WP_(IO2) */
+			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x19 /* SPI_A_/HOLD_(IO3) */
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82 /* SPI_B_SDI */
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82 /* SPI_B_SDO */
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82 /* SPI_B_SCK */
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19 /* SPI_B_CS0# */
+		>;
+	};
+
+	pinctrl_enet_rgmii: enetrgmiigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x03 /* ETH_MDC */
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x03 /* ETH_MDIO */
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f /* ETH_A_(S)(R)(G)MII_TXD3 */
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f /* ETH_A_(S)(R)(G)MII_TXD2 */
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f /* ETH_A_(S)(R)(G)MII_TXD1 */
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f /* ETH_A_(S)(R)(G)MII_TXD0 */
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91 /* ETH_A_(R)(G)MII_RXD3 */
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91 /* ETH_A_(R)(G)MII_RXD2 */
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91 /* ETH_A_(S)(R)(G)MII_RXD1 */
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91 /* ETH_A_(S)(R)(G)MII_RXD0 */
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f /* ETH_A_(R)(G)MII_TX_CLK */
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91 /* ETH_A_(R)(G)MII_RX_CLK */
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+		>;
+	};
+
+	pinctrl_enet_rmii: enetrmiigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x03 /* ETH_MDC */
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x03 /* ETH_MDIO */
+			MX8MM_IOMUXC_ENET_TD2_ENET1_TX_CLK		0x4000001f /* ETH_A_(S)(R)(G)MII_TXD2 */
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x56 /* ETH_A_(S)(R)(G)MII_TXD1 */
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x56 /* ETH_A_(S)(R)(G)MII_TXD0 */
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x56 /* ETH_A_(S)(R)(G)MII_RXD1 */
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x56 /* ETH_A_(S)(R)(G)MII_RXD0 */
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RX_ER		0x56 /* ETH_A_(R)(G)MII_RX_CLK */
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x56 /* ETH_A_(R)(G)MII_RX_DV(_ER) */
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x56 /* ETH_A_(R)(G)MII_TX_EN(_ER) */
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19 /* GPIO_A_0 */
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19 /* GPIO_A_1 */
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19 /* GPIO_A_2 */
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19 /* GPIO_A_3 */
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19 /* GPIO_A_4 */
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19 /* GPIO_A_5 */
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19 /* GPIO_A_6 */
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19 /* GPIO_A_7 */
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19 /* GPIO_B_0 */
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x19 /* GPIO_B_1 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0			0x19 /* GPIO_C_5 */
+			MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1		0x19 /* GPIO_C_4 */
+			MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6		0x19 /* GPIO_C_0 */
+			MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7		0x19 /* GPIO_C_1 */
+			MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8		0x19 /* GPIO_C_2 */
+			MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9		0x19 /* GPIO_C_3 */
+			MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x19 /* GPIO_B_2 */
+			MX8MM_IOMUXC_SAI5_RXD0_GPIO3_IO21		0x19 /* GPIO_B_3 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0		0x19 /* GPIO_C_7 */
+			MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4		0x19 /* GPIO_B_4 */
+			MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5		0x19 /* BOOT_SEL0# */
+			MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6		0x19 /* BOOT_SEL1# */
+			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x19 /* GPIO_B_5 */
+			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x19 /* GPIO_B_6 */
+			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x19 /* GPIO_B_7 */
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x19 /* GPIO_C_6 */
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000083
@@ -264,22 +588,149 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000083
 		>;
 	};
 
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x40000083 /* I2C_A_SCL */
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x40000083 /* I2C_A_SDA */
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000083 /* I2C_B_SCL */
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000083 /* I2C_B_SDA */
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000083 /* PCIe_SMCLK and I2C_CAM_SCL/CSI_TX_P */
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000083 /* PCIe_SMDAT and I2C_CAM_SDA/CSI_TX_N */
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22		0x19 /* PCIe_CLKREQ# */
+			MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x19 /* PCIe_A_PERST# */
+			MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x19 /* PCIe_WAKE# */
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19 /* PCIe_SM_ALERT */
+		>;
+	};
+
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
 		>;
 	};
 
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT		0x19 /* PWM_0 */
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19 /* PWM_1 */
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT			0x19 /* PWM_2 */
+		>;
+	};
+
+	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19 /* USB_A_EN */
+		>;
+	};
+
+	pinctrl_reg_usb2_vbus: regusb2vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x19 /* USB_B_EN */
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vcc: regusdhc2vccgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x19 /* SDIO_A_PWR_EN */
+		>;
+	};
+
+	pinctrl_reg_usdhc3_vcc: regusdhc3vccgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x19 /* SDIO_B_PWR_EN */
+		>;
+	};
+
+	pinctrl_reg_vdd_carrier: regvddcarriergrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x19 /* CARRIER_PWR_EN */
+		>;
+	};
+
 	pinctrl_rtc: rtcgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1			0x19
 		>;
 	};
 
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0		0xd6 /* I2S_A_DATA_IN */
+			MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0		0xd6 /* I2S_A_DATA_OUT */
+			MX8MM_IOMUXC_SAI1_RXD1_SAI1_RX_DATA1		0xd6 /* I2S_B_DATA_IN */
+			MX8MM_IOMUXC_SAI1_TXD1_SAI1_TX_DATA1		0xd6 /* I2S_B_DATA_OUT */
+			MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK		0xd6 /* I2S_MCLK */
+			MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC		0xd6 /* I2S_LRCLK */
+			MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK		0xd6 /* I2S_BITCLK */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x0 /* UART_A_RX */
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x0 /* UART_A_TX */
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x0 /* UART_A_CTS */
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x0 /* UART_A_RTS */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x0 /* UART_B_RX */
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x0 /* UART_B_TX */
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x0 /* UART_B_CTS */
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x0 /* UART_B_RTS */
+		>;
+	};
+
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
-			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
-			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140 /* UART_CON_RX */
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140 /* UART_CON_TX */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x0 /* UART_C_RX */
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x0 /* UART_C_TX */
+		>;
+	};
+
+	pinctrl_usb1: usb1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x19 /* USB_A_OC# */
+		>;
+	};
+
+	pinctrl_usb2: usb2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC		0x19 /* USB_B_OC# */
 		>;
 	};
 
@@ -334,6 +785,103 @@ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
 		>;
 	};
 
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x90 /* SDIO_A_CLK */
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0 /* SDIO_A_CMD */
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0 /* SDIO_A_D0 */
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0 /* SDIO_A_D1 */
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0 /* SDIO_A_D2 */
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0 /* SDIO_A_D3 */
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x94 /* SDIO_A_CLK */
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4 /* SDIO_A_CMD */
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4 /* SDIO_A_D0 */
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4 /* SDIO_A_D1 */
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4 /* SDIO_A_D2 */
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4 /* SDIO_A_D3 */
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x96 /* SDIO_A_CLK */
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6 /* SDIO_A_CMD */
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6 /* SDIO_A_D0 */
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6 /* SDIO_A_D1 */
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6 /* SDIO_A_D2 */
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6 /* SDIO_A_D3 */
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6 /* SDIO_A_WP */
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x90
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x19 /* SDIO_A_CD# */
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x90 /* SDIO_B_CLK */
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x90 /* SDIO_B_CMD */
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x90 /* SDIO_B_D0 */
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x90 /* SDIO_B_D1 */
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x90 /* SDIO_B_D2 */
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x90 /* SDIO_B_D3 */
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x90 /* SDIO_B_D4 */
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x90 /* SDIO_B_D5 */
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x90 /* SDIO_B_D6 */
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x90 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x94 /* SDIO_B_CLK */
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x94 /* SDIO_B_CMD */
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x94 /* SDIO_B_D0 */
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x94 /* SDIO_B_D1 */
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x94 /* SDIO_B_D2 */
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x94 /* SDIO_B_D3 */
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x94 /* SDIO_B_D4 */
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x94 /* SDIO_B_D5 */
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x94 /* SDIO_B_D6 */
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x94 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x96 /* SDIO_B_CLK */
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x96 /* SDIO_B_CMD */
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x96 /* SDIO_B_D0 */
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x96 /* SDIO_B_D1 */
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x96 /* SDIO_B_D2 */
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x96 /* SDIO_B_D3 */
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x96 /* SDIO_B_D4 */
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x96 /* SDIO_B_D5 */
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x96 /* SDIO_B_D6 */
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x96 /* SDIO_B_D7 */
+		>;
+	};
+
+	pinctrl_usdhc3_gpio: usdhc3gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19 /* SDIO_B_CD# */
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19 /* SDIO_B_WP */
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
-- 
2.42.0