[PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[Thomas Richard]

On j7200, during suspend to ram the SoC is powered-off. So the pinctrl
contexts are lost.
The flag PCS_CONTEXT_LOSS_OFF shall be set to restore the pinctrl
contexts.

A new compatible (ti,j7200-padconf) was created to enable this flag only
for j7200.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
Thomas Richard (3):
      dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible
      pinctrl: pinctrl-single: add ti,j7200-padconf compatible
      arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

 .../devicetree/bindings/pinctrl/pinctrl-single.yaml          |  1 +
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi                    |  8 ++++----
 arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi              | 12 ++++++------
 drivers/pinctrl/pinctrl-single.c                             |  5 +++++
 4 files changed, 16 insertions(+), 10 deletions(-)
---
base-commit: 2a20795e4274c0d94c14fcb8309f72699e404d99
change-id: 20231128-j7200-pinctrl-s2r-95cb9c159a9e

Best regards,
-- 
Thomas Richard <thomas.richard@bootlin.com>

[PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[Thomas Richard]

On j7200, during suspend to ram the SoC is powered-off. So the pinctrl
contexts are lost.
The flag PCS_CONTEXT_LOSS_OFF shall be set to restore the pinctrl
contexts.

A new compatible (ti,j7200-padconf) was created to enable this flag only
for j7200.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
Thomas Richard (3):
      dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible
      pinctrl: pinctrl-single: add ti,j7200-padconf compatible
      arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

 .../devicetree/bindings/pinctrl/pinctrl-single.yaml          |  1 +
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi                    |  8 ++++----
 arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi              | 12 ++++++------
 drivers/pinctrl/pinctrl-single.c                             |  5 +++++
 4 files changed, 16 insertions(+), 10 deletions(-)
---
base-commit: 2a20795e4274c0d94c14fcb8309f72699e404d99
change-id: 20231128-j7200-pinctrl-s2r-95cb9c159a9e

Best regards,
-- 
Thomas Richard <thomas.richard@bootlin.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/3] dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Thomas Richard]

Add the "ti,j7200-padconf" compatible to support suspend to ram on
j7200.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
index 45a307d3ce16..c11495524dd2 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
@@ -31,6 +31,7 @@ properties:
               - ti,omap3-padconf
               - ti,omap4-padconf
               - ti,omap5-padconf
+              - ti,j7200-padconf
           - const: pinctrl-single
 
   reg:

-- 
2.39.2

[PATCH 1/3] dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Thomas Richard]

Add the "ti,j7200-padconf" compatible to support suspend to ram on
j7200.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
index 45a307d3ce16..c11495524dd2 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.yaml
@@ -31,6 +31,7 @@ properties:
               - ti,omap3-padconf
               - ti,omap4-padconf
               - ti,omap5-padconf
+              - ti,j7200-padconf
           - const: pinctrl-single
 
   reg:

-- 
2.39.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/3] pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Thomas Richard]

On j7200, during suspend to ram pinctrl contexts are lost. To save and
restore contexts during suspend/resume, the flag PCS_CONTEXT_LOSS_OFF
shall be set.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 drivers/pinctrl/pinctrl-single.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index 8267be769635..19cc0db771a5 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -1955,6 +1955,10 @@ static const struct pcs_soc_data pinctrl_single_am654 = {
 	.irq_status_mask = (1 << 30),   /* WKUP_EVT */
 };
 
+static const struct pcs_soc_data pinctrl_single_j7200 = {
+	.flags = PCS_CONTEXT_LOSS_OFF,
+};
+
 static const struct pcs_soc_data pinctrl_single = {
 };
 
@@ -1969,6 +1973,7 @@ static const struct of_device_id pcs_of_match[] = {
 	{ .compatible = "ti,omap3-padconf", .data = &pinctrl_single_omap_wkup },
 	{ .compatible = "ti,omap4-padconf", .data = &pinctrl_single_omap_wkup },
 	{ .compatible = "ti,omap5-padconf", .data = &pinctrl_single_omap_wkup },
+	{ .compatible = "ti,j7200-padconf", .data = &pinctrl_single_j7200 },
 	{ .compatible = "pinctrl-single", .data = &pinctrl_single },
 	{ .compatible = "pinconf-single", .data = &pinconf_single },
 	{ },

-- 
2.39.2

[PATCH 2/3] pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Thomas Richard]

On j7200, during suspend to ram pinctrl contexts are lost. To save and
restore contexts during suspend/resume, the flag PCS_CONTEXT_LOSS_OFF
shall be set.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 drivers/pinctrl/pinctrl-single.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index 8267be769635..19cc0db771a5 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -1955,6 +1955,10 @@ static const struct pcs_soc_data pinctrl_single_am654 = {
 	.irq_status_mask = (1 << 30),   /* WKUP_EVT */
 };
 
+static const struct pcs_soc_data pinctrl_single_j7200 = {
+	.flags = PCS_CONTEXT_LOSS_OFF,
+};
+
 static const struct pcs_soc_data pinctrl_single = {
 };
 
@@ -1969,6 +1973,7 @@ static const struct of_device_id pcs_of_match[] = {
 	{ .compatible = "ti,omap3-padconf", .data = &pinctrl_single_omap_wkup },
 	{ .compatible = "ti,omap4-padconf", .data = &pinctrl_single_omap_wkup },
 	{ .compatible = "ti,omap5-padconf", .data = &pinctrl_single_omap_wkup },
+	{ .compatible = "ti,j7200-padconf", .data = &pinctrl_single_j7200 },
 	{ .compatible = "pinctrl-single", .data = &pinctrl_single },
 	{ .compatible = "pinconf-single", .data = &pinconf_single },
 	{ },

-- 
2.39.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Thomas Richard]

For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
restore pinctrl contexts.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi       |  8 ++++----
 arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 12 ++++++------
 2 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 1ea809e41500..709081cd1e7f 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -395,7 +395,7 @@ cpts@3d000 {
 
 	/* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */
 	main_timerio_input: pinctrl@104200 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x104200 0x0 0x50>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -404,7 +404,7 @@ main_timerio_input: pinctrl@104200 {
 
 	/* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */
 	main_timerio_output: pinctrl@104280 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x104280 0x0 0x20>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -412,7 +412,7 @@ main_timerio_output: pinctrl@104280 {
 	};
 
 	main_pmx0: pinctrl@11c000 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x11c000 0x00 0x10c>;
 		#pinctrl-cells = <1>;
@@ -421,7 +421,7 @@ main_pmx0: pinctrl@11c000 {
 	};
 
 	main_pmx1: pinctrl@11c11c {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x11c11c 0x00 0xc>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 3fc588b848c6..467970fab3a0 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -185,7 +185,7 @@ chipid@43000014 {
 
 	/* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
 	mcu_timerio_input: pinctrl@40f04200 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x40f04200 0x0 0x28>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -195,7 +195,7 @@ mcu_timerio_input: pinctrl@40f04200 {
 
 	/* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */
 	mcu_timerio_output: pinctrl@40f04280 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x40f04280 0x0 0x28>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -204,7 +204,7 @@ mcu_timerio_output: pinctrl@40f04280 {
 	};
 
 	wkup_pmx0: pinctrl@4301c000 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c000 0x00 0x34>;
 		#pinctrl-cells = <1>;
@@ -213,7 +213,7 @@ wkup_pmx0: pinctrl@4301c000 {
 	};
 
 	wkup_pmx1: pinctrl@4301c038 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c038 0x00 0x8>;
 		#pinctrl-cells = <1>;
@@ -222,7 +222,7 @@ wkup_pmx1: pinctrl@4301c038 {
 	};
 
 	wkup_pmx2: pinctrl@4301c068 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c068 0x00 0xec>;
 		#pinctrl-cells = <1>;
@@ -231,7 +231,7 @@ wkup_pmx2: pinctrl@4301c068 {
 	};
 
 	wkup_pmx3: pinctrl@4301c174 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c174 0x00 0x20>;
 		#pinctrl-cells = <1>;

-- 
2.39.2

[PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Thomas Richard]

For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
restore pinctrl contexts.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi       |  8 ++++----
 arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 12 ++++++------
 2 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 1ea809e41500..709081cd1e7f 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -395,7 +395,7 @@ cpts@3d000 {
 
 	/* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */
 	main_timerio_input: pinctrl@104200 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x104200 0x0 0x50>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -404,7 +404,7 @@ main_timerio_input: pinctrl@104200 {
 
 	/* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */
 	main_timerio_output: pinctrl@104280 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x104280 0x0 0x20>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -412,7 +412,7 @@ main_timerio_output: pinctrl@104280 {
 	};
 
 	main_pmx0: pinctrl@11c000 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x11c000 0x00 0x10c>;
 		#pinctrl-cells = <1>;
@@ -421,7 +421,7 @@ main_pmx0: pinctrl@11c000 {
 	};
 
 	main_pmx1: pinctrl@11c11c {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x11c11c 0x00 0xc>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 3fc588b848c6..467970fab3a0 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -185,7 +185,7 @@ chipid@43000014 {
 
 	/* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
 	mcu_timerio_input: pinctrl@40f04200 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x40f04200 0x0 0x28>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -195,7 +195,7 @@ mcu_timerio_input: pinctrl@40f04200 {
 
 	/* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */
 	mcu_timerio_output: pinctrl@40f04280 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		reg = <0x0 0x40f04280 0x0 0x28>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
@@ -204,7 +204,7 @@ mcu_timerio_output: pinctrl@40f04280 {
 	};
 
 	wkup_pmx0: pinctrl@4301c000 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c000 0x00 0x34>;
 		#pinctrl-cells = <1>;
@@ -213,7 +213,7 @@ wkup_pmx0: pinctrl@4301c000 {
 	};
 
 	wkup_pmx1: pinctrl@4301c038 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c038 0x00 0x8>;
 		#pinctrl-cells = <1>;
@@ -222,7 +222,7 @@ wkup_pmx1: pinctrl@4301c038 {
 	};
 
 	wkup_pmx2: pinctrl@4301c068 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c068 0x00 0xec>;
 		#pinctrl-cells = <1>;
@@ -231,7 +231,7 @@ wkup_pmx2: pinctrl@4301c068 {
 	};
 
 	wkup_pmx3: pinctrl@4301c174 {
-		compatible = "pinctrl-single";
+		compatible = "ti,j7200-padconf", "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c174 0x00 0x20>;
 		#pinctrl-cells = <1>;

-- 
2.39.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 285 bytes --]

On Tue, Nov 28, 2023 at 04:34:59PM +0100, Thomas Richard wrote:
> Add the "ti,j7200-padconf" compatible to support suspend to ram on
> j7200.
> 
> Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>

Acked-by: Conor Dooley <conor.dooley@microchip.com>

Cheers,
Conor.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 1/3] dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Conor Dooley]

[-- Attachment #1.1: Type: text/plain, Size: 285 bytes --]

On Tue, Nov 28, 2023 at 04:34:59PM +0100, Thomas Richard wrote:
> Add the "ti,j7200-padconf" compatible to support suspend to ram on
> j7200.
> 
> Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>

Acked-by: Conor Dooley <conor.dooley@microchip.com>

Cheers,
Conor.

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
> Add the "ti,j7200-padconf" compatible to support suspend to ram on
> j7200.

Reviewed-by: Tony Lindgren <tony@atomide.com>

Re: [PATCH 1/3] dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
> Add the "ti,j7200-padconf" compatible to support suspend to ram on
> j7200.

Reviewed-by: Tony Lindgren <tony@atomide.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/3] pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
> On j7200, during suspend to ram pinctrl contexts are lost. To save and
> restore contexts during suspend/resume, the flag PCS_CONTEXT_LOSS_OFF
> shall be set.

Reviewed-by: Tony Lindgren <tony@atomide.com>

Re: [PATCH 2/3] pinctrl: pinctrl-single: add ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
> On j7200, during suspend to ram pinctrl contexts are lost. To save and
> restore contexts during suspend/resume, the flag PCS_CONTEXT_LOSS_OFF
> shall be set.

Reviewed-by: Tony Lindgren <tony@atomide.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
> For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
> restore pinctrl contexts.

Hmm are the mcu registers lost too? Anyways presumably you looked at it:

Reviewed-by: Tony Lindgren <tony@atomide.com>

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
> For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
> restore pinctrl contexts.

Hmm are the mcu registers lost too? Anyways presumably you looked at it:

Reviewed-by: Tony Lindgren <tony@atomide.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Thomas Richard]

On 11/29/23 11:19, Tony Lindgren wrote:
> * Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
>> For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
>> restore pinctrl contexts.
> 
> Hmm are the mcu registers lost too? Anyways presumably you looked at it:

Hi Tony,

Thanks for the review.
Yes the mcu registers are lost too, as the SoC is fully powered-off.
And I did the test to confirm.

Regards,

> 
> Reviewed-by: Tony Lindgren <tony@atomide.com>
-- 
Thomas Richard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Thomas Richard]

On 11/29/23 11:19, Tony Lindgren wrote:
> * Thomas Richard <thomas.richard@bootlin.com> [231128 15:35]:
>> For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
>> restore pinctrl contexts.
> 
> Hmm are the mcu registers lost too? Anyways presumably you looked at it:

Hi Tony,

Thanks for the review.
Yes the mcu registers are lost too, as the SoC is fully powered-off.
And I did the test to confirm.

Regards,

> 
> Reviewed-by: Tony Lindgren <tony@atomide.com>
-- 
Thomas Richard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231129 10:32]:
> Thanks for the review.
> Yes the mcu registers are lost too, as the SoC is fully powered-off.
> And I did the test to confirm.

OK thanks for confirming it.

Tony

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Tony Lindgren]

* Thomas Richard <thomas.richard@bootlin.com> [231129 10:32]:
> Thanks for the review.
> Yes the mcu registers are lost too, as the SoC is fully powered-off.
> And I did the test to confirm.

OK thanks for confirming it.

Tony

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[Linus Walleij]

On Tue, Nov 28, 2023 at 4:35 PM Thomas Richard
<thomas.richard@bootlin.com> wrote:

> Thomas Richard (3):
>       dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible
>       pinctrl: pinctrl-single: add ti,j7200-padconf compatible

Patch 1 & 2 applied to the pin control tree, thanks!

>       arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

Please funnel this through the SoC tree.

Yours,
Linus Walleij

Re: [PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[Linus Walleij]

On Tue, Nov 28, 2023 at 4:35 PM Thomas Richard
<thomas.richard@bootlin.com> wrote:

> Thomas Richard (3):
>       dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible
>       pinctrl: pinctrl-single: add ti,j7200-padconf compatible

Patch 1 & 2 applied to the pin control tree, thanks!

>       arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

Please funnel this through the SoC tree.

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Linus Walleij]

On Tue, Nov 28, 2023 at 4:35 PM Thomas Richard
<thomas.richard@bootlin.com> wrote:

> For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
> restore pinctrl contexts.
>
> Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

Re: [PATCH 3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible

[Linus Walleij]

On Tue, Nov 28, 2023 at 4:35 PM Thomas Richard
<thomas.richard@bootlin.com> wrote:

> For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
> restore pinctrl contexts.
>
> Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: (subset)[PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[Vignesh Raghavendra]

Hi Thomas Richard,

On Tue, 28 Nov 2023 16:34:58 +0100, Thomas Richard wrote:
> On j7200, during suspend to ram the SoC is powered-off. So the pinctrl
> contexts are lost.
> The flag PCS_CONTEXT_LOSS_OFF shall be set to restore the pinctrl
> contexts.
> 
> A new compatible (ti,j7200-padconf) was created to enable this flag only
> for j7200.
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible
      commit: 4eb42afed5d488c4707be5362e8e0f0771f5218e

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: (subset)[PATCH 0/3] pinctrl: pinctrl-single: fix suspend/resume on j7200

[Vignesh Raghavendra]

Hi Thomas Richard,

On Tue, 28 Nov 2023 16:34:58 +0100, Thomas Richard wrote:
> On j7200, during suspend to ram the SoC is powered-off. So the pinctrl
> contexts are lost.
> The flag PCS_CONTEXT_LOSS_OFF shall be set to restore the pinctrl
> contexts.
> 
> A new compatible (ti,j7200-padconf) was created to enable this flag only
> for j7200.
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[3/3] arm64: dts: ti: k3-j7200: use ti,j7200-padconf compatible
      commit: 4eb42afed5d488c4707be5362e8e0f0771f5218e

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh