* [PATCH 0/4] Add pm8010 RPMH regulators for sm8550 boards
@ 2023-12-11 3:16 ` Fenglin Wu
0 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu via B4 Relay @ 2023-12-11 3:16 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
There are 2 PM8010 PMICs present in sm8550-mtp/sm8550-qrd boards and
each of them exposes 7 LDOs. Add RPMH regulator support for them.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
Fenglin Wu (4):
regulator: qcom-rpmh: extend to support multiple linear voltage ranges
regulator: qcom,rpmh: add compatible for pm8010 RPMH regultor
regulator: qcom-rpmh: add support for pm8010 regulators
arm64: dts: qcom: Add pm8010 regulators for sm8550 boards
.../bindings/regulator/qcom,rpmh-regulator.yaml | 14 ++
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 120 ++++++++++++++
arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 120 ++++++++++++++
drivers/regulator/qcom-rpmh-regulator.c | 177 ++++++++++++++++++---
4 files changed, 405 insertions(+), 26 deletions(-)
---
base-commit: 753e4d5c433da57da75dd4c3e1aececc8e874a62
change-id: 20231205-pm8010-regulator-0348cb19087a
Best regards,
--
Fenglin Wu <quic_fenglinw@quicinc.com>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/4] Add pm8010 RPMH regulators for sm8550 boards
@ 2023-12-11 3:16 ` Fenglin Wu
0 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu @ 2023-12-11 3:16 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
There are 2 PM8010 PMICs present in sm8550-mtp/sm8550-qrd boards and
each of them exposes 7 LDOs. Add RPMH regulator support for them.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
Fenglin Wu (4):
regulator: qcom-rpmh: extend to support multiple linear voltage ranges
regulator: qcom,rpmh: add compatible for pm8010 RPMH regultor
regulator: qcom-rpmh: add support for pm8010 regulators
arm64: dts: qcom: Add pm8010 regulators for sm8550 boards
.../bindings/regulator/qcom,rpmh-regulator.yaml | 14 ++
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 120 ++++++++++++++
arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 120 ++++++++++++++
drivers/regulator/qcom-rpmh-regulator.c | 177 ++++++++++++++++++---
4 files changed, 405 insertions(+), 26 deletions(-)
---
base-commit: 753e4d5c433da57da75dd4c3e1aececc8e874a62
change-id: 20231205-pm8010-regulator-0348cb19087a
Best regards,
--
Fenglin Wu <quic_fenglinw@quicinc.com>
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/4] regulator: qcom-rpmh: extend to support multiple linear voltage ranges
2023-12-11 3:16 ` Fenglin Wu
@ 2023-12-11 3:16 ` Fenglin Wu
-1 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu via B4 Relay @ 2023-12-11 3:16 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
From: Fenglin Wu <quic_fenglinw@quicinc.com>
Update rpmh_vreg_hw_data to support multiple linear voltage ranges for
potential regulators which have discrete voltage program ranges.
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
drivers/regulator/qcom-rpmh-regulator.c | 115 ++++++++++++++++++++++++--------
1 file changed, 89 insertions(+), 26 deletions(-)
diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
index cf502eec0915..43b45feb02e6 100644
--- a/drivers/regulator/qcom-rpmh-regulator.c
+++ b/drivers/regulator/qcom-rpmh-regulator.c
@@ -1,5 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
// Copyright (c) 2018-2021, The Linux Foundation. All rights reserved.
+// Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
#define pr_fmt(fmt) "%s: " fmt, __func__
@@ -68,10 +69,11 @@ enum rpmh_regulator_type {
* @regulator_type: RPMh accelerator type used to manage this
* regulator
* @ops: Pointer to regulator ops callback structure
- * @voltage_range: The single range of voltages supported by this
- * PMIC regulator type
+ * @voltage_ranges: The possible ranges of voltages supported by this
+ * PMIC regulator type
+ * @n_linear_ranges: Number of entries in voltage_ranges
* @n_voltages: The number of unique voltage set points defined
- * by voltage_range
+ * by voltage_ranges
* @hpm_min_load_uA: Minimum load current in microamps that requires
* high power mode (HPM) operation. This is used
* for LDO hardware type regulators only.
@@ -85,7 +87,8 @@ enum rpmh_regulator_type {
struct rpmh_vreg_hw_data {
enum rpmh_regulator_type regulator_type;
const struct regulator_ops *ops;
- const struct linear_range voltage_range;
+ const struct linear_range *voltage_ranges;
+ int n_linear_ranges;
int n_voltages;
int hpm_min_load_uA;
const int *pmic_mode_map;
@@ -449,8 +452,8 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
vreg->mode = REGULATOR_MODE_INVALID;
if (rpmh_data->hw_data->n_voltages) {
- vreg->rdesc.linear_ranges = &rpmh_data->hw_data->voltage_range;
- vreg->rdesc.n_linear_ranges = 1;
+ vreg->rdesc.linear_ranges = rpmh_data->hw_data->voltage_ranges;
+ vreg->rdesc.n_linear_ranges = rpmh_data->hw_data->n_linear_ranges;
vreg->rdesc.n_voltages = rpmh_data->hw_data->n_voltages;
}
@@ -613,7 +616,10 @@ static unsigned int rpmh_regulator_pmic4_bob_of_map_mode(unsigned int rpmh_mode)
static const struct rpmh_vreg_hw_data pmic4_pldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1664000, 0, 255, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1664000, 0, 255, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 256,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic4_ldo,
@@ -623,7 +629,10 @@ static const struct rpmh_vreg_hw_data pmic4_pldo = {
static const struct rpmh_vreg_hw_data pmic4_pldo_lv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1256000, 0, 127, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1256000, 0, 127, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 128,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic4_ldo,
@@ -633,7 +642,10 @@ static const struct rpmh_vreg_hw_data pmic4_pldo_lv = {
static const struct rpmh_vreg_hw_data pmic4_nldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 128,
.hpm_min_load_uA = 30000,
.pmic_mode_map = pmic_mode_map_pmic4_ldo,
@@ -643,7 +655,10 @@ static const struct rpmh_vreg_hw_data pmic4_nldo = {
static const struct rpmh_vreg_hw_data pmic4_hfsmps3 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 216,
.pmic_mode_map = pmic_mode_map_pmic4_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -652,7 +667,10 @@ static const struct rpmh_vreg_hw_data pmic4_hfsmps3 = {
static const struct rpmh_vreg_hw_data pmic4_ftsmps426 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 259,
.pmic_mode_map = pmic_mode_map_pmic4_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -661,7 +679,10 @@ static const struct rpmh_vreg_hw_data pmic4_ftsmps426 = {
static const struct rpmh_vreg_hw_data pmic4_bob = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_bypass_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1824000, 0, 83, 32000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1824000, 0, 83, 32000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 84,
.pmic_mode_map = pmic_mode_map_pmic4_bob,
.of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
@@ -676,7 +697,10 @@ static const struct rpmh_vreg_hw_data pmic4_lvs = {
static const struct rpmh_vreg_hw_data pmic5_pldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 256,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -686,7 +710,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo = {
static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 63,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -696,7 +723,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 188,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -706,7 +736,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
static const struct rpmh_vreg_hw_data pmic5_nldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 124,
.hpm_min_load_uA = 30000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -716,7 +749,10 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = {
static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 211,
.hpm_min_load_uA = 30000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -726,7 +762,10 @@ static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 216,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -735,7 +774,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 264,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -744,7 +786,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps520 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 264,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -753,7 +798,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps520 = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps525_lv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 267, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(300000, 0, 267, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 268,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -762,7 +810,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_lv = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(600000, 0, 267, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(600000, 0, 267, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 268,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -771,7 +822,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 215,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -780,7 +834,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 236,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -789,7 +846,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
static const struct rpmh_vreg_hw_data pmic5_hfsmps515_1 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(900000, 0, 4, 16000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(900000, 0, 4, 16000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 5,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -798,7 +858,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515_1 = {
static const struct rpmh_vreg_hw_data pmic5_bob = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_bypass_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(3000000, 0, 31, 32000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(3000000, 0, 31, 32000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 32,
.pmic_mode_map = pmic_mode_map_pmic5_bob,
.of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 1/4] regulator: qcom-rpmh: extend to support multiple linear voltage ranges
@ 2023-12-11 3:16 ` Fenglin Wu
0 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu @ 2023-12-11 3:16 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
Update rpmh_vreg_hw_data to support multiple linear voltage ranges for
potential regulators which have discrete voltage program ranges.
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
drivers/regulator/qcom-rpmh-regulator.c | 115 ++++++++++++++++++++++++--------
1 file changed, 89 insertions(+), 26 deletions(-)
diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
index cf502eec0915..43b45feb02e6 100644
--- a/drivers/regulator/qcom-rpmh-regulator.c
+++ b/drivers/regulator/qcom-rpmh-regulator.c
@@ -1,5 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
// Copyright (c) 2018-2021, The Linux Foundation. All rights reserved.
+// Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
#define pr_fmt(fmt) "%s: " fmt, __func__
@@ -68,10 +69,11 @@ enum rpmh_regulator_type {
* @regulator_type: RPMh accelerator type used to manage this
* regulator
* @ops: Pointer to regulator ops callback structure
- * @voltage_range: The single range of voltages supported by this
- * PMIC regulator type
+ * @voltage_ranges: The possible ranges of voltages supported by this
+ * PMIC regulator type
+ * @n_linear_ranges: Number of entries in voltage_ranges
* @n_voltages: The number of unique voltage set points defined
- * by voltage_range
+ * by voltage_ranges
* @hpm_min_load_uA: Minimum load current in microamps that requires
* high power mode (HPM) operation. This is used
* for LDO hardware type regulators only.
@@ -85,7 +87,8 @@ enum rpmh_regulator_type {
struct rpmh_vreg_hw_data {
enum rpmh_regulator_type regulator_type;
const struct regulator_ops *ops;
- const struct linear_range voltage_range;
+ const struct linear_range *voltage_ranges;
+ int n_linear_ranges;
int n_voltages;
int hpm_min_load_uA;
const int *pmic_mode_map;
@@ -449,8 +452,8 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
vreg->mode = REGULATOR_MODE_INVALID;
if (rpmh_data->hw_data->n_voltages) {
- vreg->rdesc.linear_ranges = &rpmh_data->hw_data->voltage_range;
- vreg->rdesc.n_linear_ranges = 1;
+ vreg->rdesc.linear_ranges = rpmh_data->hw_data->voltage_ranges;
+ vreg->rdesc.n_linear_ranges = rpmh_data->hw_data->n_linear_ranges;
vreg->rdesc.n_voltages = rpmh_data->hw_data->n_voltages;
}
@@ -613,7 +616,10 @@ static unsigned int rpmh_regulator_pmic4_bob_of_map_mode(unsigned int rpmh_mode)
static const struct rpmh_vreg_hw_data pmic4_pldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1664000, 0, 255, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1664000, 0, 255, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 256,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic4_ldo,
@@ -623,7 +629,10 @@ static const struct rpmh_vreg_hw_data pmic4_pldo = {
static const struct rpmh_vreg_hw_data pmic4_pldo_lv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1256000, 0, 127, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1256000, 0, 127, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 128,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic4_ldo,
@@ -633,7 +642,10 @@ static const struct rpmh_vreg_hw_data pmic4_pldo_lv = {
static const struct rpmh_vreg_hw_data pmic4_nldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 128,
.hpm_min_load_uA = 30000,
.pmic_mode_map = pmic_mode_map_pmic4_ldo,
@@ -643,7 +655,10 @@ static const struct rpmh_vreg_hw_data pmic4_nldo = {
static const struct rpmh_vreg_hw_data pmic4_hfsmps3 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 216,
.pmic_mode_map = pmic_mode_map_pmic4_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -652,7 +667,10 @@ static const struct rpmh_vreg_hw_data pmic4_hfsmps3 = {
static const struct rpmh_vreg_hw_data pmic4_ftsmps426 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 259,
.pmic_mode_map = pmic_mode_map_pmic4_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -661,7 +679,10 @@ static const struct rpmh_vreg_hw_data pmic4_ftsmps426 = {
static const struct rpmh_vreg_hw_data pmic4_bob = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_bypass_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1824000, 0, 83, 32000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1824000, 0, 83, 32000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 84,
.pmic_mode_map = pmic_mode_map_pmic4_bob,
.of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
@@ -676,7 +697,10 @@ static const struct rpmh_vreg_hw_data pmic4_lvs = {
static const struct rpmh_vreg_hw_data pmic5_pldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 256,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -686,7 +710,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo = {
static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 63,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -696,7 +723,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 188,
.hpm_min_load_uA = 10000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -706,7 +736,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
static const struct rpmh_vreg_hw_data pmic5_nldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 124,
.hpm_min_load_uA = 30000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -716,7 +749,10 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = {
static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 211,
.hpm_min_load_uA = 30000,
.pmic_mode_map = pmic_mode_map_pmic5_ldo,
@@ -726,7 +762,10 @@ static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 216,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -735,7 +774,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 264,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -744,7 +786,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps520 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 264,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -753,7 +798,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps520 = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps525_lv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 267, 4000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(300000, 0, 267, 4000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 268,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -762,7 +810,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_lv = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(600000, 0, 267, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(600000, 0, 267, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 268,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -771,7 +822,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 215,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -780,7 +834,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 236,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -789,7 +846,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
static const struct rpmh_vreg_hw_data pmic5_hfsmps515_1 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(900000, 0, 4, 16000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(900000, 0, 4, 16000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 5,
.pmic_mode_map = pmic_mode_map_pmic5_smps,
.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
@@ -798,7 +858,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515_1 = {
static const struct rpmh_vreg_hw_data pmic5_bob = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_bypass_ops,
- .voltage_range = REGULATOR_LINEAR_RANGE(3000000, 0, 31, 32000),
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(3000000, 0, 31, 32000),
+ },
+ .n_linear_ranges = 1,
.n_voltages = 32,
.pmic_mode_map = pmic_mode_map_pmic5_bob,
.of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/4] regulator: qcom,rpmh: add compatible for pm8010 RPMH regultor
2023-12-11 3:16 ` Fenglin Wu
@ 2023-12-11 3:17 ` Fenglin Wu
-1 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu via B4 Relay @ 2023-12-11 3:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
From: Fenglin Wu <quic_fenglinw@quicinc.com>
Add compatible for PM8010 RPMH regulators present on sm8550-qrd and
sm8550-mtp boards.
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
.../devicetree/bindings/regulator/qcom,rpmh-regulator.yaml | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
index acd37f28ef53..27c6d5152413 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
@@ -42,6 +42,7 @@ description: |
For PM7325, smps1 - smps8, ldo1 - ldo19
For PM8005, smps1 - smps4
For PM8009, smps1 - smps2, ldo1 - ldo7
+ For PM8010, ldo1 - ldo7
For PM8150, smps1 - smps10, ldo1 - ldo18
For PM8150L, smps1 - smps8, ldo1 - ldo11, bob, flash, rgb
For PM8350, smps1 - smps12, ldo1 - ldo10
@@ -68,6 +69,7 @@ properties:
- qcom,pm8005-rpmh-regulators
- qcom,pm8009-rpmh-regulators
- qcom,pm8009-1-rpmh-regulators
+ - qcom,pm8010-rpmh-regulators
- qcom,pm8150-rpmh-regulators
- qcom,pm8150l-rpmh-regulators
- qcom,pm8350-rpmh-regulators
@@ -238,6 +240,18 @@ allOf:
"^vdd-l[1-47]-supply$": true
"^vdd-s[1-2]-supply$": true
+ - if:
+ properties:
+ compatible:
+ enum:
+ - qcom,pm8010-rpmh-regulators
+ then:
+ properties:
+ vdd-l1-l2-supply: true
+ vdd-l3-l4-supply: true
+ patternProperties:
+ "^vdd-l[5-7]-supply$": true
+
- if:
properties:
compatible:
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/4] regulator: qcom,rpmh: add compatible for pm8010 RPMH regultor
@ 2023-12-11 3:17 ` Fenglin Wu
0 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu @ 2023-12-11 3:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
Add compatible for PM8010 RPMH regulators present on sm8550-qrd and
sm8550-mtp boards.
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
.../devicetree/bindings/regulator/qcom,rpmh-regulator.yaml | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
index acd37f28ef53..27c6d5152413 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
@@ -42,6 +42,7 @@ description: |
For PM7325, smps1 - smps8, ldo1 - ldo19
For PM8005, smps1 - smps4
For PM8009, smps1 - smps2, ldo1 - ldo7
+ For PM8010, ldo1 - ldo7
For PM8150, smps1 - smps10, ldo1 - ldo18
For PM8150L, smps1 - smps8, ldo1 - ldo11, bob, flash, rgb
For PM8350, smps1 - smps12, ldo1 - ldo10
@@ -68,6 +69,7 @@ properties:
- qcom,pm8005-rpmh-regulators
- qcom,pm8009-rpmh-regulators
- qcom,pm8009-1-rpmh-regulators
+ - qcom,pm8010-rpmh-regulators
- qcom,pm8150-rpmh-regulators
- qcom,pm8150l-rpmh-regulators
- qcom,pm8350-rpmh-regulators
@@ -238,6 +240,18 @@ allOf:
"^vdd-l[1-47]-supply$": true
"^vdd-s[1-2]-supply$": true
+ - if:
+ properties:
+ compatible:
+ enum:
+ - qcom,pm8010-rpmh-regulators
+ then:
+ properties:
+ vdd-l1-l2-supply: true
+ vdd-l3-l4-supply: true
+ patternProperties:
+ "^vdd-l[5-7]-supply$": true
+
- if:
properties:
compatible:
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/4] regulator: qcom-rpmh: add support for pm8010 regulators
2023-12-11 3:16 ` Fenglin Wu
@ 2023-12-11 3:17 ` Fenglin Wu
-1 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu via B4 Relay @ 2023-12-11 3:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
From: Fenglin Wu <quic_fenglinw@quicinc.com>
Add RPMH regulators exposed by Qualcomm Technologies, Inc. PM8010
PMIC. It has 7 LDOs with 3 different types, LDO1 - LDO2 are L502
NMOS LDOs, LDO5 and LDO7 are L502 PMOS LDOs, LDO3/LDO4/LDO6 are
L502 PMOS LDO for low noise applications. Also, LDO3 - LDO7 don't
support LPM.
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
drivers/regulator/qcom-rpmh-regulator.c | 62 +++++++++++++++++++++++++++++++++
1 file changed, 62 insertions(+)
diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
index 43b45feb02e6..80e304711345 100644
--- a/drivers/regulator/qcom-rpmh-regulator.c
+++ b/drivers/regulator/qcom-rpmh-regulator.c
@@ -511,6 +511,14 @@ static const int pmic_mode_map_pmic5_ldo[REGULATOR_MODE_STANDBY + 1] = {
[REGULATOR_MODE_FAST] = -EINVAL,
};
+static const int pmic_mode_map_pmic5_ldo_hpm[REGULATOR_MODE_STANDBY + 1] = {
+ [REGULATOR_MODE_INVALID] = -EINVAL,
+ [REGULATOR_MODE_STANDBY] = -EINVAL,
+ [REGULATOR_MODE_IDLE] = -EINVAL,
+ [REGULATOR_MODE_NORMAL] = PMIC5_LDO_MODE_HPM,
+ [REGULATOR_MODE_FAST] = -EINVAL,
+};
+
static unsigned int rpmh_regulator_pmic4_ldo_of_map_mode(unsigned int rpmh_mode)
{
unsigned int mode;
@@ -733,6 +741,33 @@ static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
};
+static const struct rpmh_vreg_hw_data pmic5_pldo502 = {
+ .regulator_type = VRM,
+ .ops = &rpmh_regulator_vrm_ops,
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
+ },
+ .n_linear_ranges = 1,
+ .n_voltages = 256,
+ .pmic_mode_map = pmic_mode_map_pmic5_ldo_hpm,
+ .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
+static const struct rpmh_vreg_hw_data pmic5_pldo502ln = {
+ .regulator_type = VRM,
+ .ops = &rpmh_regulator_vrm_ops,
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1800000, 0, 2, 200000),
+ REGULATOR_LINEAR_RANGE(2608000, 3, 28, 16000),
+ REGULATOR_LINEAR_RANGE(3104000, 29, 30, 96000),
+ REGULATOR_LINEAR_RANGE(3312000, 31, 31, 0),
+ },
+ .n_linear_ranges = 4,
+ .n_voltages = 32,
+ .pmic_mode_map = pmic_mode_map_pmic5_ldo_hpm,
+ .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
static const struct rpmh_vreg_hw_data pmic5_nldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
@@ -759,6 +794,19 @@ static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
};
+static const struct rpmh_vreg_hw_data pmic5_nldo502 = {
+ .regulator_type = VRM,
+ .ops = &rpmh_regulator_vrm_drms_ops,
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(528000, 0, 127, 8000),
+ },
+ .n_linear_ranges = 1,
+ .n_voltages = 128,
+ .hpm_min_load_uA = 30000,
+ .pmic_mode_map = pmic_mode_map_pmic5_ldo,
+ .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
@@ -1210,6 +1258,16 @@ static const struct rpmh_vreg_init_data pm8009_1_vreg_data[] = {
{}
};
+static const struct rpmh_vreg_init_data pm8010_vreg_data[] = {
+ RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo502, "vdd-l1-l2"),
+ RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo502, "vdd-l1-l2"),
+ RPMH_VREG("ldo3", "ldo%s3", &pmic5_pldo502ln, "vdd-l3-l4"),
+ RPMH_VREG("ldo4", "ldo%s4", &pmic5_pldo502ln, "vdd-l3-l4"),
+ RPMH_VREG("ldo5", "ldo%s5", &pmic5_pldo502, "vdd-l5"),
+ RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo502ln, "vdd-l6"),
+ RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo502, "vdd-l7"),
+};
+
static const struct rpmh_vreg_init_data pm6150_vreg_data[] = {
RPMH_VREG("smps1", "smp%s1", &pmic5_ftsmps510, "vdd-s1"),
RPMH_VREG("smps2", "smp%s2", &pmic5_ftsmps510, "vdd-s2"),
@@ -1525,6 +1583,10 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = {
.compatible = "qcom,pm8009-1-rpmh-regulators",
.data = pm8009_1_vreg_data,
},
+ {
+ .compatible = "qcom,pm8010-rpmh-regulators",
+ .data = pm8010_vreg_data,
+ },
{
.compatible = "qcom,pm8150-rpmh-regulators",
.data = pm8150_vreg_data,
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/4] regulator: qcom-rpmh: add support for pm8010 regulators
@ 2023-12-11 3:17 ` Fenglin Wu
0 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu @ 2023-12-11 3:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
Add RPMH regulators exposed by Qualcomm Technologies, Inc. PM8010
PMIC. It has 7 LDOs with 3 different types, LDO1 - LDO2 are L502
NMOS LDOs, LDO5 and LDO7 are L502 PMOS LDOs, LDO3/LDO4/LDO6 are
L502 PMOS LDO for low noise applications. Also, LDO3 - LDO7 don't
support LPM.
Suggested-by: David Collins <quic_collinsd@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
drivers/regulator/qcom-rpmh-regulator.c | 62 +++++++++++++++++++++++++++++++++
1 file changed, 62 insertions(+)
diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
index 43b45feb02e6..80e304711345 100644
--- a/drivers/regulator/qcom-rpmh-regulator.c
+++ b/drivers/regulator/qcom-rpmh-regulator.c
@@ -511,6 +511,14 @@ static const int pmic_mode_map_pmic5_ldo[REGULATOR_MODE_STANDBY + 1] = {
[REGULATOR_MODE_FAST] = -EINVAL,
};
+static const int pmic_mode_map_pmic5_ldo_hpm[REGULATOR_MODE_STANDBY + 1] = {
+ [REGULATOR_MODE_INVALID] = -EINVAL,
+ [REGULATOR_MODE_STANDBY] = -EINVAL,
+ [REGULATOR_MODE_IDLE] = -EINVAL,
+ [REGULATOR_MODE_NORMAL] = PMIC5_LDO_MODE_HPM,
+ [REGULATOR_MODE_FAST] = -EINVAL,
+};
+
static unsigned int rpmh_regulator_pmic4_ldo_of_map_mode(unsigned int rpmh_mode)
{
unsigned int mode;
@@ -733,6 +741,33 @@ static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
};
+static const struct rpmh_vreg_hw_data pmic5_pldo502 = {
+ .regulator_type = VRM,
+ .ops = &rpmh_regulator_vrm_ops,
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
+ },
+ .n_linear_ranges = 1,
+ .n_voltages = 256,
+ .pmic_mode_map = pmic_mode_map_pmic5_ldo_hpm,
+ .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
+static const struct rpmh_vreg_hw_data pmic5_pldo502ln = {
+ .regulator_type = VRM,
+ .ops = &rpmh_regulator_vrm_ops,
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(1800000, 0, 2, 200000),
+ REGULATOR_LINEAR_RANGE(2608000, 3, 28, 16000),
+ REGULATOR_LINEAR_RANGE(3104000, 29, 30, 96000),
+ REGULATOR_LINEAR_RANGE(3312000, 31, 31, 0),
+ },
+ .n_linear_ranges = 4,
+ .n_voltages = 32,
+ .pmic_mode_map = pmic_mode_map_pmic5_ldo_hpm,
+ .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
static const struct rpmh_vreg_hw_data pmic5_nldo = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_drms_ops,
@@ -759,6 +794,19 @@ static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
};
+static const struct rpmh_vreg_hw_data pmic5_nldo502 = {
+ .regulator_type = VRM,
+ .ops = &rpmh_regulator_vrm_drms_ops,
+ .voltage_ranges = (struct linear_range[]) {
+ REGULATOR_LINEAR_RANGE(528000, 0, 127, 8000),
+ },
+ .n_linear_ranges = 1,
+ .n_voltages = 128,
+ .hpm_min_load_uA = 30000,
+ .pmic_mode_map = pmic_mode_map_pmic5_ldo,
+ .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
.regulator_type = VRM,
.ops = &rpmh_regulator_vrm_ops,
@@ -1210,6 +1258,16 @@ static const struct rpmh_vreg_init_data pm8009_1_vreg_data[] = {
{}
};
+static const struct rpmh_vreg_init_data pm8010_vreg_data[] = {
+ RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo502, "vdd-l1-l2"),
+ RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo502, "vdd-l1-l2"),
+ RPMH_VREG("ldo3", "ldo%s3", &pmic5_pldo502ln, "vdd-l3-l4"),
+ RPMH_VREG("ldo4", "ldo%s4", &pmic5_pldo502ln, "vdd-l3-l4"),
+ RPMH_VREG("ldo5", "ldo%s5", &pmic5_pldo502, "vdd-l5"),
+ RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo502ln, "vdd-l6"),
+ RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo502, "vdd-l7"),
+};
+
static const struct rpmh_vreg_init_data pm6150_vreg_data[] = {
RPMH_VREG("smps1", "smp%s1", &pmic5_ftsmps510, "vdd-s1"),
RPMH_VREG("smps2", "smp%s2", &pmic5_ftsmps510, "vdd-s2"),
@@ -1525,6 +1583,10 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = {
.compatible = "qcom,pm8009-1-rpmh-regulators",
.data = pm8009_1_vreg_data,
},
+ {
+ .compatible = "qcom,pm8010-rpmh-regulators",
+ .data = pm8010_vreg_data,
+ },
{
.compatible = "qcom,pm8150-rpmh-regulators",
.data = pm8150_vreg_data,
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/4] arm64: dts: qcom: Add pm8010 regulators for sm8550 boards
2023-12-11 3:16 ` Fenglin Wu
@ 2023-12-11 3:17 ` Fenglin Wu
-1 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu via B4 Relay @ 2023-12-11 3:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
From: Fenglin Wu <quic_fenglinw@quicinc.com>
Add PM8010 regulator device nodes for sm8550-mtp and sm8550-qrd boards.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 120 ++++++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 120 ++++++++++++++++++++++++++++++++
2 files changed, 240 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index 9a70875028b7..8395d363d18d 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -510,6 +510,126 @@ vreg_l3g_1p2: ldo3 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p3>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p8>;
+ vdd-l6-supply = <&vreg_s6g_1p8>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p3>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p8>;
+ vdd-l6-supply = <&vreg_bob1>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
};
&i2c_master_hub_0 {
diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index eef811def39b..7ca93c149215 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -527,6 +527,126 @@ vreg_l3g_1p2: ldo3 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p25>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p86>;
+ vdd-l6-supply = <&vreg_s6g_1p86>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p25>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p86>;
+ vdd-l6-supply = <&vreg_bob1>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
};
&i2c_master_hub_0 {
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/4] arm64: dts: qcom: Add pm8010 regulators for sm8550 boards
@ 2023-12-11 3:17 ` Fenglin Wu
0 siblings, 0 replies; 14+ messages in thread
From: Fenglin Wu @ 2023-12-11 3:17 UTC (permalink / raw)
To: Andy Gross, Bjorn Andersson, Konrad Dybcio, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash, Fenglin Wu
Add PM8010 regulator device nodes for sm8550-mtp and sm8550-qrd boards.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 120 ++++++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 120 ++++++++++++++++++++++++++++++++
2 files changed, 240 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index 9a70875028b7..8395d363d18d 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -510,6 +510,126 @@ vreg_l3g_1p2: ldo3 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p3>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p8>;
+ vdd-l6-supply = <&vreg_s6g_1p8>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p3>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p8>;
+ vdd-l6-supply = <&vreg_bob1>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
};
&i2c_master_hub_0 {
diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index eef811def39b..7ca93c149215 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -527,6 +527,126 @@ vreg_l3g_1p2: ldo3 {
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
};
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p25>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p86>;
+ vdd-l6-supply = <&vreg_s6g_1p86>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vdd-l1-l2-supply = <&vreg_s4g_1p25>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6g_1p86>;
+ vdd-l6-supply = <&vreg_bob1>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
};
&i2c_master_hub_0 {
--
2.25.1
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 2/4] regulator: qcom,rpmh: add compatible for pm8010 RPMH regultor
2023-12-11 3:17 ` Fenglin Wu
(?)
@ 2023-12-11 7:58 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2023-12-11 7:58 UTC (permalink / raw)
To: quic_fenglinw, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Liam Girdwood, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, kernel
Cc: linux-arm-msm, linux-kernel, devicetree, quic_collinsd,
quic_subbaram, quic_jprakash
On 11/12/2023 04:17, Fenglin Wu via B4 Relay wrote:
> From: Fenglin Wu <quic_fenglinw@quicinc.com>
>
> Add compatible for PM8010 RPMH regulators present on sm8550-qrd and
> sm8550-mtp boards.
>
> Suggested-by: David Collins <quic_collinsd@quicinc.com>
> Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.
Also fix typo: regultor->regulator
With both fixed:
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 4/4] arm64: dts: qcom: Add pm8010 regulators for sm8550 boards
2023-12-11 3:17 ` Fenglin Wu
(?)
@ 2023-12-11 9:29 ` Konrad Dybcio
-1 siblings, 0 replies; 14+ messages in thread
From: Konrad Dybcio @ 2023-12-11 9:29 UTC (permalink / raw)
To: quic_fenglinw, Andy Gross, Bjorn Andersson, Liam Girdwood,
Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_collinsd, quic_subbaram, quic_jprakash
On 11.12.2023 04:17, Fenglin Wu via B4 Relay wrote:
> From: Fenglin Wu <quic_fenglinw@quicinc.com>
>
> Add PM8010 regulator device nodes for sm8550-mtp and sm8550-qrd boards.
>
> Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
> ---
Please create separate commits with board name prefixes:
arm64: dts: qcom: sm8550-mtp:
arm64: dts: qcom: sm8550-qrd:
Otherwise lgtm
Konrad
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] regulator: qcom-rpmh: extend to support multiple linear voltage ranges
2023-12-11 3:16 ` Fenglin Wu
(?)
@ 2023-12-12 2:44 ` David Collins
-1 siblings, 0 replies; 14+ messages in thread
From: David Collins @ 2023-12-12 2:44 UTC (permalink / raw)
To: quic_fenglinw, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Liam Girdwood, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_subbaram, quic_jprakash
On 12/10/23 19:16, Fenglin Wu via B4 Relay wrote:
> From: Fenglin Wu <quic_fenglinw@quicinc.com>
>
> Update rpmh_vreg_hw_data to support multiple linear voltage ranges for
> potential regulators which have discrete voltage program ranges.
>
> Suggested-by: David Collins <quic_collinsd@quicinc.com>
> Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
> ---
> drivers/regulator/qcom-rpmh-regulator.c | 115 ++++++++++++++++++++++++--------
> 1 file changed, 89 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
> index cf502eec0915..43b45feb02e6 100644
> --- a/drivers/regulator/qcom-rpmh-regulator.c
> +++ b/drivers/regulator/qcom-rpmh-regulator.c
> @@ -1,5 +1,6 @@
> // SPDX-License-Identifier: GPL-2.0
> // Copyright (c) 2018-2021, The Linux Foundation. All rights reserved.
> +// Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
>
> #define pr_fmt(fmt) "%s: " fmt, __func__
>
> @@ -68,10 +69,11 @@ enum rpmh_regulator_type {
> * @regulator_type: RPMh accelerator type used to manage this
> * regulator
> * @ops: Pointer to regulator ops callback structure
> - * @voltage_range: The single range of voltages supported by this
> - * PMIC regulator type
> + * @voltage_ranges: The possible ranges of voltages supported by this
> + * PMIC regulator type
> + * @n_linear_ranges: Number of entries in voltage_ranges
> * @n_voltages: The number of unique voltage set points defined
> - * by voltage_range
> + * by voltage_ranges
> * @hpm_min_load_uA: Minimum load current in microamps that requires
> * high power mode (HPM) operation. This is used
> * for LDO hardware type regulators only.
> @@ -85,7 +87,8 @@ enum rpmh_regulator_type {
> struct rpmh_vreg_hw_data {
> enum rpmh_regulator_type regulator_type;
> const struct regulator_ops *ops;
> - const struct linear_range voltage_range;
> + const struct linear_range *voltage_ranges;
> + int n_linear_ranges;
> int n_voltages;
> int hpm_min_load_uA;
> const int *pmic_mode_map;
> @@ -449,8 +452,8 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
> vreg->mode = REGULATOR_MODE_INVALID;
>
> if (rpmh_data->hw_data->n_voltages) {
> - vreg->rdesc.linear_ranges = &rpmh_data->hw_data->voltage_range;
> - vreg->rdesc.n_linear_ranges = 1;
> + vreg->rdesc.linear_ranges = rpmh_data->hw_data->voltage_ranges;
> + vreg->rdesc.n_linear_ranges = rpmh_data->hw_data->n_linear_ranges;
> vreg->rdesc.n_voltages = rpmh_data->hw_data->n_voltages;
> }
>
> @@ -613,7 +616,10 @@ static unsigned int rpmh_regulator_pmic4_bob_of_map_mode(unsigned int rpmh_mode)
> static const struct rpmh_vreg_hw_data pmic4_pldo = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(1664000, 0, 255, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1664000, 0, 255, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 256,
> .hpm_min_load_uA = 10000,
> .pmic_mode_map = pmic_mode_map_pmic4_ldo,
> @@ -623,7 +629,10 @@ static const struct rpmh_vreg_hw_data pmic4_pldo = {
> static const struct rpmh_vreg_hw_data pmic4_pldo_lv = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(1256000, 0, 127, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1256000, 0, 127, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 128,
> .hpm_min_load_uA = 10000,
> .pmic_mode_map = pmic_mode_map_pmic4_ldo,
> @@ -633,7 +642,10 @@ static const struct rpmh_vreg_hw_data pmic4_pldo_lv = {
> static const struct rpmh_vreg_hw_data pmic4_nldo = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 128,
> .hpm_min_load_uA = 30000,
> .pmic_mode_map = pmic_mode_map_pmic4_ldo,
> @@ -643,7 +655,10 @@ static const struct rpmh_vreg_hw_data pmic4_nldo = {
> static const struct rpmh_vreg_hw_data pmic4_hfsmps3 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 216,
> .pmic_mode_map = pmic_mode_map_pmic4_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -652,7 +667,10 @@ static const struct rpmh_vreg_hw_data pmic4_hfsmps3 = {
> static const struct rpmh_vreg_hw_data pmic4_ftsmps426 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 259,
> .pmic_mode_map = pmic_mode_map_pmic4_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -661,7 +679,10 @@ static const struct rpmh_vreg_hw_data pmic4_ftsmps426 = {
> static const struct rpmh_vreg_hw_data pmic4_bob = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_bypass_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(1824000, 0, 83, 32000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1824000, 0, 83, 32000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 84,
> .pmic_mode_map = pmic_mode_map_pmic4_bob,
> .of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
> @@ -676,7 +697,10 @@ static const struct rpmh_vreg_hw_data pmic4_lvs = {
> static const struct rpmh_vreg_hw_data pmic5_pldo = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 256,
> .hpm_min_load_uA = 10000,
> .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> @@ -686,7 +710,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo = {
> static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1504000, 0, 62, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 63,
> .hpm_min_load_uA = 10000,
> .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> @@ -696,7 +723,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
> static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 188,
> .hpm_min_load_uA = 10000,
> .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> @@ -706,7 +736,10 @@ static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
> static const struct rpmh_vreg_hw_data pmic5_nldo = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 123, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 124,
> .hpm_min_load_uA = 30000,
> .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> @@ -716,7 +749,10 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = {
> static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 211,
> .hpm_min_load_uA = 30000,
> .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> @@ -726,7 +762,10 @@ static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
> static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 216,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -735,7 +774,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
> static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 264,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -744,7 +786,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps510 = {
> static const struct rpmh_vreg_hw_data pmic5_ftsmps520 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(300000, 0, 263, 4000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 264,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -753,7 +798,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps520 = {
> static const struct rpmh_vreg_hw_data pmic5_ftsmps525_lv = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(300000, 0, 267, 4000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(300000, 0, 267, 4000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 268,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -762,7 +810,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_lv = {
> static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(600000, 0, 267, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(600000, 0, 267, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 268,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -771,7 +822,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
> static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 215,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -780,7 +834,10 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
> static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(320000, 0, 235, 16000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 236,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -789,7 +846,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
> static const struct rpmh_vreg_hw_data pmic5_hfsmps515_1 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(900000, 0, 4, 16000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(900000, 0, 4, 16000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 5,
> .pmic_mode_map = pmic_mode_map_pmic5_smps,
> .of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> @@ -798,7 +858,10 @@ static const struct rpmh_vreg_hw_data pmic5_hfsmps515_1 = {
> static const struct rpmh_vreg_hw_data pmic5_bob = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_bypass_ops,
> - .voltage_range = REGULATOR_LINEAR_RANGE(3000000, 0, 31, 32000),
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(3000000, 0, 31, 32000),
> + },
> + .n_linear_ranges = 1,
> .n_voltages = 32,
> .pmic_mode_map = pmic_mode_map_pmic5_bob,
> .of_map_mode = rpmh_regulator_pmic4_bob_of_map_mode,
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 3/4] regulator: qcom-rpmh: add support for pm8010 regulators
2023-12-11 3:17 ` Fenglin Wu
(?)
@ 2023-12-12 2:44 ` David Collins
-1 siblings, 0 replies; 14+ messages in thread
From: David Collins @ 2023-12-12 2:44 UTC (permalink / raw)
To: quic_fenglinw, Andy Gross, Bjorn Andersson, Konrad Dybcio,
Liam Girdwood, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, kernel
Cc: Krzysztof Kozlowski, linux-arm-msm, linux-kernel, devicetree,
quic_subbaram, quic_jprakash
On 12/10/23 19:17, Fenglin Wu via B4 Relay wrote:
> From: Fenglin Wu <quic_fenglinw@quicinc.com>
>
> Add RPMH regulators exposed by Qualcomm Technologies, Inc. PM8010
> PMIC. It has 7 LDOs with 3 different types, LDO1 - LDO2 are L502
> NMOS LDOs, LDO5 and LDO7 are L502 PMOS LDOs, LDO3/LDO4/LDO6 are
> L502 PMOS LDO for low noise applications. Also, LDO3 - LDO7 don't
> support LPM.
>
> Suggested-by: David Collins <quic_collinsd@quicinc.com>
> Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
> ---
> drivers/regulator/qcom-rpmh-regulator.c | 62 +++++++++++++++++++++++++++++++++
> 1 file changed, 62 insertions(+)
>
> diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
> index 43b45feb02e6..80e304711345 100644
> --- a/drivers/regulator/qcom-rpmh-regulator.c
> +++ b/drivers/regulator/qcom-rpmh-regulator.c
> @@ -511,6 +511,14 @@ static const int pmic_mode_map_pmic5_ldo[REGULATOR_MODE_STANDBY + 1] = {
> [REGULATOR_MODE_FAST] = -EINVAL,
> };
>
> +static const int pmic_mode_map_pmic5_ldo_hpm[REGULATOR_MODE_STANDBY + 1] = {
Minor: This is fine as-is. However, it might be a bit better with the
name: "pmic_mode_map_pmic5_ldo_hpm_only".
> + [REGULATOR_MODE_INVALID] = -EINVAL,
> + [REGULATOR_MODE_STANDBY] = -EINVAL,
> + [REGULATOR_MODE_IDLE] = -EINVAL,
> + [REGULATOR_MODE_NORMAL] = PMIC5_LDO_MODE_HPM,
> + [REGULATOR_MODE_FAST] = -EINVAL,
> +};
> +
> static unsigned int rpmh_regulator_pmic4_ldo_of_map_mode(unsigned int rpmh_mode)
> {
> unsigned int mode;
> @@ -733,6 +741,33 @@ static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
> .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> };
>
> +static const struct rpmh_vreg_hw_data pmic5_pldo502 = {
> + .regulator_type = VRM,
> + .ops = &rpmh_regulator_vrm_ops,
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1504000, 0, 255, 8000),
> + },
> + .n_linear_ranges = 1,
> + .n_voltages = 256,
> + .pmic_mode_map = pmic_mode_map_pmic5_ldo_hpm,
> + .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> +};
> +
> +static const struct rpmh_vreg_hw_data pmic5_pldo502ln = {
> + .regulator_type = VRM,
> + .ops = &rpmh_regulator_vrm_ops,
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(1800000, 0, 2, 200000),
> + REGULATOR_LINEAR_RANGE(2608000, 3, 28, 16000),
> + REGULATOR_LINEAR_RANGE(3104000, 29, 30, 96000),
> + REGULATOR_LINEAR_RANGE(3312000, 31, 31, 0),
> + },
> + .n_linear_ranges = 4,
> + .n_voltages = 32,
> + .pmic_mode_map = pmic_mode_map_pmic5_ldo_hpm,
> + .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> +};
> +
> static const struct rpmh_vreg_hw_data pmic5_nldo = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_drms_ops,
> @@ -759,6 +794,19 @@ static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
> .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> };
>
> +static const struct rpmh_vreg_hw_data pmic5_nldo502 = {
> + .regulator_type = VRM,
> + .ops = &rpmh_regulator_vrm_drms_ops,
> + .voltage_ranges = (struct linear_range[]) {
> + REGULATOR_LINEAR_RANGE(528000, 0, 127, 8000),
> + },
> + .n_linear_ranges = 1,
> + .n_voltages = 128,
> + .hpm_min_load_uA = 30000,
> + .pmic_mode_map = pmic_mode_map_pmic5_ldo,
> + .of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> +};
> +
> static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
> .regulator_type = VRM,
> .ops = &rpmh_regulator_vrm_ops,
> @@ -1210,6 +1258,16 @@ static const struct rpmh_vreg_init_data pm8009_1_vreg_data[] = {
> {}
> };
>
> +static const struct rpmh_vreg_init_data pm8010_vreg_data[] = {
> + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo502, "vdd-l1-l2"),
> + RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo502, "vdd-l1-l2"),
> + RPMH_VREG("ldo3", "ldo%s3", &pmic5_pldo502ln, "vdd-l3-l4"),
> + RPMH_VREG("ldo4", "ldo%s4", &pmic5_pldo502ln, "vdd-l3-l4"),
> + RPMH_VREG("ldo5", "ldo%s5", &pmic5_pldo502, "vdd-l5"),
> + RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo502ln, "vdd-l6"),
> + RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo502, "vdd-l7"),
> +};
> +
> static const struct rpmh_vreg_init_data pm6150_vreg_data[] = {
> RPMH_VREG("smps1", "smp%s1", &pmic5_ftsmps510, "vdd-s1"),
> RPMH_VREG("smps2", "smp%s2", &pmic5_ftsmps510, "vdd-s2"),
> @@ -1525,6 +1583,10 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = {
> .compatible = "qcom,pm8009-1-rpmh-regulators",
> .data = pm8009_1_vreg_data,
> },
> + {
> + .compatible = "qcom,pm8010-rpmh-regulators",
> + .data = pm8010_vreg_data,
> + },
> {
> .compatible = "qcom,pm8150-rpmh-regulators",
> .data = pm8150_vreg_data,
>
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2023-12-12 2:45 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-12-11 3:16 [PATCH 0/4] Add pm8010 RPMH regulators for sm8550 boards Fenglin Wu via B4 Relay
2023-12-11 3:16 ` Fenglin Wu
2023-12-11 3:16 ` [PATCH 1/4] regulator: qcom-rpmh: extend to support multiple linear voltage ranges Fenglin Wu via B4 Relay
2023-12-11 3:16 ` Fenglin Wu
2023-12-12 2:44 ` David Collins
2023-12-11 3:17 ` [PATCH 2/4] regulator: qcom,rpmh: add compatible for pm8010 RPMH regultor Fenglin Wu via B4 Relay
2023-12-11 3:17 ` Fenglin Wu
2023-12-11 7:58 ` Krzysztof Kozlowski
2023-12-11 3:17 ` [PATCH 3/4] regulator: qcom-rpmh: add support for pm8010 regulators Fenglin Wu via B4 Relay
2023-12-11 3:17 ` Fenglin Wu
2023-12-12 2:44 ` David Collins
2023-12-11 3:17 ` [PATCH 4/4] arm64: dts: qcom: Add pm8010 regulators for sm8550 boards Fenglin Wu via B4 Relay
2023-12-11 3:17 ` Fenglin Wu
2023-12-11 9:29 ` Konrad Dybcio
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.