* [PATCH 0/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
@ 2024-03-28 23:08 ` Alexandru Marc Serdeliuc
0 siblings, 0 replies; 12+ messages in thread
From: Alexandru Marc Serdeliuc via B4 Relay @ 2024-03-28 23:08 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandru Marc Serdeliuc
Added the binding file to the same patch that includes the device tree.
Refactored the decivetree
- removed bootargs
- removed unused nodes
- removed disabled nodes
- added missing identation
- removed all the comments at the end of the nodes
- moved node status at the end of the nodes
- ordered all the nodes alphabetically
- ran the recommended dtbs tests all returned success
Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
Alexandru Marc Serdeliuc (2):
V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 584 ++++++++++++++++++++++++
3 files changed, 586 insertions(+)
---
base-commit: 4cece764965020c22cff7665b18a012006359095
change-id: 20240328-v2-dts-add-support-for-samsung-galaxy-zfold5-44b90138f3be
Best regards,
--
Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
@ 2024-03-28 23:08 ` Alexandru Marc Serdeliuc
0 siblings, 0 replies; 12+ messages in thread
From: Alexandru Marc Serdeliuc @ 2024-03-28 23:08 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandru Marc Serdeliuc
Added the binding file to the same patch that includes the device tree.
Refactored the decivetree
- removed bootargs
- removed unused nodes
- removed disabled nodes
- added missing identation
- removed all the comments at the end of the nodes
- moved node status at the end of the nodes
- ordered all the nodes alphabetically
- ran the recommended dtbs tests all returned success
Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
Alexandru Marc Serdeliuc (2):
V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 584 ++++++++++++++++++++++++
3 files changed, 586 insertions(+)
---
base-commit: 4cece764965020c22cff7665b18a012006359095
change-id: 20240328-v2-dts-add-support-for-samsung-galaxy-zfold5-44b90138f3be
Best regards,
--
Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
@ 2024-03-28 23:08 ` Alexandru Marc Serdeliuc
-1 siblings, 0 replies; 12+ messages in thread
From: Alexandru Marc Serdeliuc via B4 Relay @ 2024-03-28 23:08 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandru Marc Serdeliuc
From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons
Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 584 ++++++++++++++++++++++++
2 files changed, 585 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..a7503fd35b6c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8550-samsung-q5q.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
new file mode 100644
index 000000000000..aec375fc32b4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
@@ -0,0 +1,584 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
+ * Copyright (c) 2024, David Wronek <david@mainlining.org>
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/ {
+ model = "Samsung Galaxy Z Fold5";
+ compatible = "samsung,q5q", "qcom,sm8550";
+ #address-cells = <0x02>;
+ #size-cells = <0x02>;
+ chassis-type = "handset";
+
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer: framebuffer@b8000000 {
+ compatible = "simple-framebuffer";
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ width = <2176>;
+ height = <1812>;
+ stride = <(2176 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ /*
+ * The bootloader will only keep display hardware enabled
+ * if this memory region is named exactly 'splash_region'
+ */
+ splash_region@b8000000 {
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ no-map;
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l3c_0p91: ldo3 {
+ regulator-name = "vreg_l3c_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vreg_s4e_0p9: smps4 {
+ regulator-name = "vreg_s4e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_1p1: smps5 {
+ regulator-name = "vreg_s5e_1p1";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p88: ldo1 {
+ regulator-name = "vreg_l1e_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2e_0p9: ldo2 {
+ regulator-name = "vreg_l2e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vreg_s4f_0p5: smps4 {
+ regulator-name = "vreg_s4f_0p5";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_0p9: ldo1 {
+ regulator-name = "vreg_l1f_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_0p88: ldo2 {
+ regulator-name = "vreg_l2f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_0p91: ldo3 {
+ regulator-name = "vreg_l3f_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vreg_s1g_1p2: smps1 {
+ regulator-name = "vreg_s1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2g_0p8: smps2 {
+ regulator-name = "vreg_s2g_0p8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3g_0p7: smps3 {
+ regulator-name = "vreg_s3g_0p7";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4g_1p3: smps4 {
+ regulator-name = "vreg_s4g_1p3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5g_0p8: smps5 {
+ regulator-name = "vreg_s5g_0p8";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6g_1p8: smps6 {
+ regulator-name = "vreg_s6g_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1g_1p2: ldo1 {
+ regulator-name = "vreg_l1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2g_1p2: ldo2 {
+ regulator-name = "vreg_l2g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_1p2: ldo3 {
+ regulator-name = "vreg_l3g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+
+&dispcc {
+ status = "disabled";
+};
+
+&i2c_master_hub_0 {
+ status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+ clock-frequency = <1000>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_default_state>;
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1e_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&pcie1 {
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_default_state>;
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l3c_0p91>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ vdda-qref-supply = <&vreg_l1e_0p88>;
+ status = "okay";
+};
+
+&pm8550_gpios {
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8550/adsp.mbn",
+ "qcom/sm8550/adsp_dtb.mbn";
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8550/cdsp.mbn",
+ "qcom/sm8550/cdsp_dtb.mbn";
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8550/modem.mbn",
+ "qcom/sm8550/modem_dtb.mbn";
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <36 4>, <50 2>;
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1g_1p2>;
+ vccq-max-microamp = <1200000>;
+ vdd-hba-supply = <&vreg_l3g_1p2>;
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 1/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
@ 2024-03-28 23:08 ` Alexandru Marc Serdeliuc
0 siblings, 0 replies; 12+ messages in thread
From: Alexandru Marc Serdeliuc @ 2024-03-28 23:08 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandru Marc Serdeliuc
Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons
Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 584 ++++++++++++++++++++++++
2 files changed, 585 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..a7503fd35b6c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx224.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8550-samsung-q5q.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
new file mode 100644
index 000000000000..aec375fc32b4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
@@ -0,0 +1,584 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
+ * Copyright (c) 2024, David Wronek <david@mainlining.org>
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/ {
+ model = "Samsung Galaxy Z Fold5";
+ compatible = "samsung,q5q", "qcom,sm8550";
+ #address-cells = <0x02>;
+ #size-cells = <0x02>;
+ chassis-type = "handset";
+
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer: framebuffer@b8000000 {
+ compatible = "simple-framebuffer";
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ width = <2176>;
+ height = <1812>;
+ stride = <(2176 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ /*
+ * The bootloader will only keep display hardware enabled
+ * if this memory region is named exactly 'splash_region'
+ */
+ splash_region@b8000000 {
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ no-map;
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l3c_0p91: ldo3 {
+ regulator-name = "vreg_l3c_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vreg_s4e_0p9: smps4 {
+ regulator-name = "vreg_s4e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_1p1: smps5 {
+ regulator-name = "vreg_s5e_1p1";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p88: ldo1 {
+ regulator-name = "vreg_l1e_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2e_0p9: ldo2 {
+ regulator-name = "vreg_l2e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vreg_s4f_0p5: smps4 {
+ regulator-name = "vreg_s4f_0p5";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_0p9: ldo1 {
+ regulator-name = "vreg_l1f_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_0p88: ldo2 {
+ regulator-name = "vreg_l2f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_0p91: ldo3 {
+ regulator-name = "vreg_l3f_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vreg_s1g_1p2: smps1 {
+ regulator-name = "vreg_s1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2g_0p8: smps2 {
+ regulator-name = "vreg_s2g_0p8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3g_0p7: smps3 {
+ regulator-name = "vreg_s3g_0p7";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4g_1p3: smps4 {
+ regulator-name = "vreg_s4g_1p3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5g_0p8: smps5 {
+ regulator-name = "vreg_s5g_0p8";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6g_1p8: smps6 {
+ regulator-name = "vreg_s6g_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1g_1p2: ldo1 {
+ regulator-name = "vreg_l1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2g_1p2: ldo2 {
+ regulator-name = "vreg_l2g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_1p2: ldo3 {
+ regulator-name = "vreg_l3g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vreg_l1m_1p056: ldo1 {
+ regulator-name = "vreg_l1m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_1p8: ldo6 {
+ regulator-name = "vreg_l6m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p9: ldo7 {
+ regulator-name = "vreg_l7m_2p9";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p1: ldo2 {
+ regulator-name = "vreg_l2n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_2p8: ldo3 {
+ regulator-name = "vreg_l3n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_2p8: ldo4 {
+ regulator-name = "vreg_l4n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_1p8: ldo5 {
+ regulator-name = "vreg_l5n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_3p3: ldo6 {
+ regulator-name = "vreg_l6n_3p3";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_2p96: ldo7 {
+ regulator-name = "vreg_l7n_2p96";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+
+&dispcc {
+ status = "disabled";
+};
+
+&i2c_master_hub_0 {
+ status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+ clock-frequency = <1000>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_default_state>;
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1e_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&pcie1 {
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_default_state>;
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l3c_0p91>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ vdda-qref-supply = <&vreg_l1e_0p88>;
+ status = "okay";
+};
+
+&pm8550_gpios {
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8550/adsp.mbn",
+ "qcom/sm8550/adsp_dtb.mbn";
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8550/cdsp.mbn",
+ "qcom/sm8550/cdsp_dtb.mbn";
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8550/modem.mbn",
+ "qcom/sm8550/modem_dtb.mbn";
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <36 4>, <50 2>;
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1g_1p2>;
+ vccq-max-microamp = <1200000>;
+ vdd-hba-supply = <&vreg_l3g_1p2>;
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
@ 2024-03-28 23:08 ` Alexandru Marc Serdeliuc
-1 siblings, 0 replies; 12+ messages in thread
From: Alexandru Marc Serdeliuc via B4 Relay @ 2024-03-28 23:08 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandru Marc Serdeliuc
From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons
Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 66beaac60e1d..dea2a23b8fc2 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1003,6 +1003,7 @@ properties:
- qcom,sm8550-hdk
- qcom,sm8550-mtp
- qcom,sm8550-qrd
+ - samsung,q5q
- const: qcom,sm8550
- items:
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
@ 2024-03-28 23:08 ` Alexandru Marc Serdeliuc
0 siblings, 0 replies; 12+ messages in thread
From: Alexandru Marc Serdeliuc @ 2024-03-28 23:08 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandru Marc Serdeliuc
Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons
Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 66beaac60e1d..dea2a23b8fc2 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1003,6 +1003,7 @@ properties:
- qcom,sm8550-hdk
- qcom,sm8550-mtp
- qcom,sm8550-qrd
+ - samsung,q5q
- const: qcom,sm8550
- items:
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
(?)
@ 2024-03-29 0:52 ` Konrad Dybcio
2024-03-29 9:42 ` Alexandru Serdeliuc
-1 siblings, 1 reply; 12+ messages in thread
From: Konrad Dybcio @ 2024-03-29 0:52 UTC (permalink / raw)
To: serdeliuk, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>
> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
>
> Currently working features:
> - Framebuffer
> - UFS
> - i2c
> - Buttons
>
> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
> ---
Your commit title now includes "V2". Move it inside the square braces the
next time around, so it's like [PATCH v3 1/2]. With b4, this should be done
automagically, though..
[...]
> +/ {
> + model = "Samsung Galaxy Z Fold5";
> + compatible = "samsung,q5q", "qcom,sm8550";
> + #address-cells = <0x02>;
> + #size-cells = <0x02>;
These two can go
[...]
> + reserved-memory {
> + /*
> + * The bootloader will only keep display hardware enabled
> + * if this memory region is named exactly 'splash_region'
> + */
Ouch.
[...]
> + vreg_l15b_1p8: ldo15 {
> + regulator-name = "vreg_l15b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + regulator-always-on;
Any particular reason as to why?
[...]
> +&remoteproc_adsp {
> + firmware-name = "qcom/sm8550/adsp.mbn",
> + "qcom/sm8550/adsp_dtb.mbn";
> + status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> + firmware-name = "qcom/sm8550/cdsp.mbn",
> + "qcom/sm8550/cdsp_dtb.mbn";
> + status = "okay";
> +};
> +
> +&remoteproc_mpss {
> + firmware-name = "qcom/sm8550/modem.mbn",
> + "qcom/sm8550/modem_dtb.mbn";
> + status = "okay";
Unless you stole one from the factory, these firmwares will not
load on your phone..
> +};
> +
> +&sleep_clk {
> + clock-frequency = <32000>;
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <36 4>, <50 2>;
Would you have an idea what these GPIOs are used for?
Konrad
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
(?)
@ 2024-03-29 0:54 ` Konrad Dybcio
2024-03-29 7:23 ` Alexandru Serdeliuc
2024-03-29 9:43 ` Alexandru Serdeliuc
-1 siblings, 2 replies; 12+ messages in thread
From: Konrad Dybcio @ 2024-03-29 0:54 UTC (permalink / raw)
To: serdeliuk, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>
> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
>
> Currently working features:
> - Framebuffer
> - UFS
> - i2c
> - Buttons
>
> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
> ---
Looks like the commit message and contents got mixed up!
Konrad
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-29 0:54 ` Konrad Dybcio
@ 2024-03-29 7:23 ` Alexandru Serdeliuc
2024-03-29 9:43 ` Alexandru Serdeliuc
1 sibling, 0 replies; 12+ messages in thread
From: Alexandru Serdeliuc @ 2024-03-29 7:23 UTC (permalink / raw)
To: Konrad Dybcio, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
Thanks, indeed, v3 will contain the right messages
On 29/3/24 1:54, Konrad Dybcio wrote:
> On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
>> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>>
>> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
>>
>> Currently working features:
>> - Framebuffer
>> - UFS
>> - i2c
>> - Buttons
>>
>> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>> ---
> Looks like the commit message and contents got mixed up!
>
> Konrad
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-29 0:52 ` Konrad Dybcio
@ 2024-03-29 9:42 ` Alexandru Serdeliuc
0 siblings, 0 replies; 12+ messages in thread
From: Alexandru Serdeliuc @ 2024-03-29 9:42 UTC (permalink / raw)
To: Konrad Dybcio, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
Thanks, i added some notes inline as I do not know how to proceed with
some if the requirements.
Just to be noted, the sm8550-samsung-q5q.dts it is based on
sm8550-mtp.dts so most of the stuff is from there
On 29/3/24 1:52, Konrad Dybcio wrote:
> On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
>> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>>
>> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
>>
>> Currently working features:
>> - Framebuffer
>> - UFS
>> - i2c
>> - Buttons
>>
>> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>> ---
The [PATCH] string is added automatically to the subject by b4, I don't
know how to add/insert custom text in there, I am going to read the b4
docs and see if i can spot how to do it.
> Your commit title now includes "V2". Move it inside the square braces the
> next time around, so it's like [PATCH v3 1/2]. With b4, this should be done
> automagically, though..
>
> [...]
>
>> +/ {
>> + model = "Samsung Galaxy Z Fold5";
>> + compatible = "samsung,q5q", "qcom,sm8550";
>> + #address-cells = <0x02>;
>> + #size-cells = <0x02>;
thanks, going to remove them
> These two can go
>
> [...]
>
>> + reserved-memory {
>> + /*
>> + * The bootloader will only keep display hardware enabled
>> + * if this memory region is named exactly 'splash_region'
>> + */
this is a reality, without it the framebuffer do not work, due to abl
https://git.codelinaro.org/clo/la/abl/tianocore/edk2/-/blob/LA.VENDOR.1.0.r2-09400-WAIPIO.QSSI14.0/QcomModulePkg/Library/BootLib/UpdateDeviceTree.c?ref_type=tags#L220
How to proceed?
> Ouch.
>
> [...]
>
>> + vreg_l15b_1p8: ldo15 {
>> + regulator-name = "vreg_l15b_1p8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + regulator-always-on;
I have removed the nodes that uses this as the driver for "Texas
Instruments i2c eUSB2" is not yet submitted by the porter, however,
those are took from the existing sm8550-mtp.dts
How to proceed?
> Any particular reason as to why?
>
> [...]
>
>> +&remoteproc_adsp {
>> + firmware-name = "qcom/sm8550/adsp.mbn",
>> + "qcom/sm8550/adsp_dtb.mbn";
>> + status = "okay";
>> +};
>> +
>> +&remoteproc_cdsp {
>> + firmware-name = "qcom/sm8550/cdsp.mbn",
>> + "qcom/sm8550/cdsp_dtb.mbn";
>> + status = "okay";
>> +};
>> +
>> +&remoteproc_mpss {
>> + firmware-name = "qcom/sm8550/modem.mbn",
>> + "qcom/sm8550/modem_dtb.mbn";
>> + status = "okay";
Those are took from the device's running Android /firmware and load
without error, I used this kind of firmware loaded on other devices as
well and seems to do the job, the lines are as well on existing
sm8550-mtp.dts
How to proceed?
> Unless you stole one from the factory, these firmwares will not
> load on your phone..
>
>> +};
>> +
>> +&sleep_clk {
>> + clock-frequency = <32000>;
>> +};
>> +
>> +&tlmm {
>> + gpio-reserved-ranges = <36 4>, <50 2>;
I have no idea, i took the ranges from the running Android FDT, without
those ranges the kernel do not boot, i can dig more into these ranges if
required
> Would you have an idea what these GPIOs are used for?
>
> Konrad
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-29 0:54 ` Konrad Dybcio
2024-03-29 7:23 ` Alexandru Serdeliuc
@ 2024-03-29 9:43 ` Alexandru Serdeliuc
1 sibling, 0 replies; 12+ messages in thread
From: Alexandru Serdeliuc @ 2024-03-29 9:43 UTC (permalink / raw)
To: Konrad Dybcio, Bjorn Andersson, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
Thanks, indeed, v3 will contain the right messages
On 29/3/24 1:54, Konrad Dybcio wrote:
> On 29.03.2024 12:08 AM, Alexandru Marc Serdeliuc via B4 Relay wrote:
>> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>>
>> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
>>
>> Currently working features:
>> - Framebuffer
>> - UFS
>> - i2c
>> - Buttons
>>
>> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>> ---
> Looks like the commit message and contents got mixed up!
>
> Konrad
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] v2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
(?)
(?)
@ 2024-03-29 12:11 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 12+ messages in thread
From: Krzysztof Kozlowski @ 2024-03-29 12:11 UTC (permalink / raw)
To: serdeliuk, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
On 29/03/2024 00:08, Alexandru Marc Serdeliuc via B4 Relay wrote:
> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>
> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone
Please use subject prefixes matching the subsystem. You can get them for
example with `git log --oneline -- DIRECTORY_OR_FILE` on the directory
your patch is touching.
v2 is for sure wrong prefix. Other parts are also wrong, which above
command will tell you.
>
> Currently working features:
> - Framebuffer
> - UFS
> - i2c
> - Buttons
>
> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
Please go back and read my response.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2024-03-29 12:11 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-03-28 23:08 [PATCH 0/2] V2 arm64: dts: qcom: Add support for Samsung Galaxy Z Fold5 Alexandru Marc Serdeliuc via B4 Relay
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
2024-03-28 23:08 ` [PATCH 1/2] " Alexandru Marc Serdeliuc via B4 Relay
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
2024-03-29 0:52 ` Konrad Dybcio
2024-03-29 9:42 ` Alexandru Serdeliuc
2024-03-28 23:08 ` [PATCH 2/2] v2 " Alexandru Marc Serdeliuc via B4 Relay
2024-03-28 23:08 ` Alexandru Marc Serdeliuc
2024-03-29 0:54 ` Konrad Dybcio
2024-03-29 7:23 ` Alexandru Serdeliuc
2024-03-29 9:43 ` Alexandru Serdeliuc
2024-03-29 12:11 ` Krzysztof Kozlowski
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.