* [PATCH v2 00/10] arm64: dts: imx8qm Add audio\flexcan\i2c\fec1 nodes for imx8qm-mek board
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
No new warning added by
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- -j8 CHECK_DTBS=y freescale/imx8qm-mek.dtb
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Changes in v2:
- move vendor property to last, just before status
- use audio-codec@1a as node name
- about dual license problem, need relicense whole included tree's dts file
which out scope this patch
- About delete-node
imx8qm-ss-audio.dtsi are not supposed to be included directly. imx8qm.dtsi
is supposed to be included by other board dts file.
in imx8qm.dtsi
/* sorted in register address */
+ #include "imx8-ss-audio.dtsi"
#include "imx8-ss-vpu.dtsi"
#include "imx8-ss-img.dtsi"
#include "imx8-ss-dma.dtsi"
@@ -473,3 +558,4 @@ drc_crit0: trip1 {
#include "imx8qm-ss-dma.dtsi"
#include "imx8qm-ss-conn.dtsi"
#include "imx8qm-ss-lsio.dtsi"
+#include "imx8qm-ss-audio.dtsi"
"imx8qm-ss-audio" will overwrite some common audio node in
"imx8-ss-audio.dtsi"
acm, and sai4/5 are defined in imx8-ss-audio.dtsi for common part for all
imx8qm\imx8qxp\imx8dxl.
- Link to v1: https://lore.kernel.org/r/20240415-dts_8qm_audio-v1-0-2976c35a0c52@nxp.com
---
Frank Li (10):
arm64: dts: imx8-ss-audio: remove memory-region = <&dsp_reserved>;
arm64: dts: imx8qm-ss-audio: add audio nodes
arm64: dts: imx8qm-mek: add sai and wm8960 support
arm64: dts: imx8x: add cm41 subsystem dtsi
arm64: dts: imx8qm-mek: add i2c0 and children devices
arm64: dts: imx8qm-mek: add cm41_i2c and children devices
arm64: dts: imx8qm-mek: add flexcan support
arm64: dts: imx8qm-mek: add lsio mu5 and mu6
arm64: dts: imx8qm: add ocopt and fec_mac[0,1]
arm64: dts: imx8qm-mek: add fec2 support
arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi | 1 -
arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi | 68 +++
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 345 +++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi | 473 +++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 102 +++++
5 files changed, 988 insertions(+), 1 deletion(-)
---
base-commit: eda9714fe6d9e6e5690992ce7dd42b13a5be7803
change-id: 20240402-dts_8qm_audio-e1e1697c9bf6
Best regards,
---
Frank Li <Frank.Li@nxp.com>
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 00/10] arm64: dts: imx8qm Add audio\flexcan\i2c\fec1 nodes for imx8qm-mek board
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
No new warning added by
make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- -j8 CHECK_DTBS=y freescale/imx8qm-mek.dtb
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Changes in v2:
- move vendor property to last, just before status
- use audio-codec@1a as node name
- about dual license problem, need relicense whole included tree's dts file
which out scope this patch
- About delete-node
imx8qm-ss-audio.dtsi are not supposed to be included directly. imx8qm.dtsi
is supposed to be included by other board dts file.
in imx8qm.dtsi
/* sorted in register address */
+ #include "imx8-ss-audio.dtsi"
#include "imx8-ss-vpu.dtsi"
#include "imx8-ss-img.dtsi"
#include "imx8-ss-dma.dtsi"
@@ -473,3 +558,4 @@ drc_crit0: trip1 {
#include "imx8qm-ss-dma.dtsi"
#include "imx8qm-ss-conn.dtsi"
#include "imx8qm-ss-lsio.dtsi"
+#include "imx8qm-ss-audio.dtsi"
"imx8qm-ss-audio" will overwrite some common audio node in
"imx8-ss-audio.dtsi"
acm, and sai4/5 are defined in imx8-ss-audio.dtsi for common part for all
imx8qm\imx8qxp\imx8dxl.
- Link to v1: https://lore.kernel.org/r/20240415-dts_8qm_audio-v1-0-2976c35a0c52@nxp.com
---
Frank Li (10):
arm64: dts: imx8-ss-audio: remove memory-region = <&dsp_reserved>;
arm64: dts: imx8qm-ss-audio: add audio nodes
arm64: dts: imx8qm-mek: add sai and wm8960 support
arm64: dts: imx8x: add cm41 subsystem dtsi
arm64: dts: imx8qm-mek: add i2c0 and children devices
arm64: dts: imx8qm-mek: add cm41_i2c and children devices
arm64: dts: imx8qm-mek: add flexcan support
arm64: dts: imx8qm-mek: add lsio mu5 and mu6
arm64: dts: imx8qm: add ocopt and fec_mac[0,1]
arm64: dts: imx8qm-mek: add fec2 support
arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi | 1 -
arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi | 68 +++
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 345 +++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi | 473 +++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 102 +++++
5 files changed, 988 insertions(+), 1 deletion(-)
---
base-commit: eda9714fe6d9e6e5690992ce7dd42b13a5be7803
change-id: 20240402-dts_8qm_audio-e1e1697c9bf6
Best regards,
---
Frank Li <Frank.Li@nxp.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v2 01/10] arm64: dts: imx8-ss-audio: remove memory-region = <&dsp_reserved>;
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Different boards have different DDR memory sizes and layouts for reserved
memory. This change reduces future dependencies to add 'imx8qm-ss-audio'.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi
index 897cbb7b67422..ff5df0fed9e96 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi
@@ -447,7 +447,6 @@ dsp: dsp@596e8000 {
<&lsio_mu13 2 1>,
<&lsio_mu13 3 0>,
<&lsio_mu13 3 1>;
- memory-region = <&dsp_reserved>;
status = "disabled";
};
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 01/10] arm64: dts: imx8-ss-audio: remove memory-region = <&dsp_reserved>;
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Different boards have different DDR memory sizes and layouts for reserved
memory. This change reduces future dependencies to add 'imx8qm-ss-audio'.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi
index 897cbb7b67422..ff5df0fed9e96 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi
@@ -447,7 +447,6 @@ dsp: dsp@596e8000 {
<&lsio_mu13 2 1>,
<&lsio_mu13 3 0>,
<&lsio_mu13 3 1>;
- memory-region = <&dsp_reserved>;
status = "disabled";
};
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 02/10] arm64: dts: imx8qm-ss-audio: add audio nodes
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add i.MX8QM audio related nodes and update eDMA[0,1]'s information.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi | 473 +++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 86 ++++
2 files changed, 559 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi
new file mode 100644
index 0000000000000..ed5a1b4af1d76
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi
@@ -0,0 +1,473 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ * Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+/delete-node/ &acm;
+/delete-node/ &sai4;
+/delete-node/ &sai5;
+/delete-node/ &sai4_lpcg;
+/delete-node/ &sai5_lpcg;
+
+/* edma2 called in imx8qm RM with the same address in edma0 of imx8qxp */
+&edma0{
+ reg = <0x591f0000 0x150000>;
+ dma-channels = <20>;
+ dma-channel-mask = <0>;
+ interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>, /* asrc0 */
+ <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>, /* esai0 */
+ <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>, /* spdif0 */
+ <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>, /* spdif1 */
+ <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, /* sai0 */
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, /* sai1 */
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, /* sai2 */
+ <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, /* sai3 */
+ <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, /* sai4 */
+ <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>; /* sai5 */
+ power-domains = <&pd IMX_SC_R_DMA_2_CH0>,
+ <&pd IMX_SC_R_DMA_2_CH1>,
+ <&pd IMX_SC_R_DMA_2_CH2>,
+ <&pd IMX_SC_R_DMA_2_CH3>,
+ <&pd IMX_SC_R_DMA_2_CH4>,
+ <&pd IMX_SC_R_DMA_2_CH5>,
+ <&pd IMX_SC_R_DMA_2_CH6>,
+ <&pd IMX_SC_R_DMA_2_CH7>,
+ <&pd IMX_SC_R_DMA_2_CH8>,
+ <&pd IMX_SC_R_DMA_2_CH9>,
+ <&pd IMX_SC_R_DMA_2_CH10>,
+ <&pd IMX_SC_R_DMA_2_CH11>,
+ <&pd IMX_SC_R_DMA_2_CH12>,
+ <&pd IMX_SC_R_DMA_2_CH13>,
+ <&pd IMX_SC_R_DMA_2_CH14>,
+ <&pd IMX_SC_R_DMA_2_CH15>,
+ <&pd IMX_SC_R_DMA_2_CH16>,
+ <&pd IMX_SC_R_DMA_2_CH17>,
+ <&pd IMX_SC_R_DMA_2_CH18>,
+ <&pd IMX_SC_R_DMA_2_CH19>;
+};
+
+/* edma3 called in imx8qm RM with the same address in edma1 of imx8qxp */
+&edma1{
+ reg = <0x599F0000 0xc0000>;
+ dma-channels = <11>;
+ dma-channel-mask = <0xc0>;
+ interrupts = <GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>, /* asrc1 */
+ <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, /* no used */
+ <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, /* no used */
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, /* sai6 */
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>; /* sai7 */
+ power-domains = <&pd IMX_SC_R_DMA_3_CH0>,
+ <&pd IMX_SC_R_DMA_3_CH1>,
+ <&pd IMX_SC_R_DMA_3_CH2>,
+ <&pd IMX_SC_R_DMA_3_CH3>,
+ <&pd IMX_SC_R_DMA_3_CH4>,
+ <&pd IMX_SC_R_DMA_3_CH5>,
+ <&pd IMX_SC_R_DMA_3_CH6>,
+ <&pd IMX_SC_R_DMA_3_CH7>,
+ <&pd IMX_SC_R_DMA_3_CH8>,
+ <&pd IMX_SC_R_DMA_3_CH9>,
+ <&pd IMX_SC_R_DMA_3_CH10>;
+};
+
+&asrc0 {
+ clocks = <&asrc0_lpcg IMX_LPCG_CLK_0>,
+ <&asrc0_lpcg IMX_LPCG_CLK_2>,
+ <&aud_pll_div0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>,
+ <&acm IMX_ADMA_ACM_AUD_CLK0_SEL>,
+ <&acm IMX_ADMA_ACM_AUD_CLK1_SEL>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_ASRC_0>;
+};
+
+&esai0 {
+ clocks = <&esai0_lpcg IMX_LPCG_CLK_0>,
+ <&esai0_lpcg IMX_LPCG_CLK_4>,
+ <&esai0_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_ESAI_0>;
+};
+
+&spdif0 {
+ clocks = <&spdif0_lpcg IMX_LPCG_CLK_4>, /* core */
+ <&clk_dummy>, /* rxtx0 */
+ <&spdif0_lpcg IMX_LPCG_CLK_5>, /* rxtx1 */
+ <&clk_dummy>, /* rxtx2 */
+ <&clk_dummy>, /* rxtx3 */
+ <&clk_dummy>, /* rxtx4 */
+ <&audio_ipg_clk>, /* rxtx5 */
+ <&clk_dummy>, /* rxtx6 */
+ <&clk_dummy>, /* rxtx7 */
+ <&clk_dummy>; /* spba */
+ power-domains = <&pd IMX_SC_R_SPDIF_0>;
+};
+
+&sai0 {
+ clocks = <&sai0_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai0_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_0>;
+};
+
+&sai1 {
+ clocks = <&sai1_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai1_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_1>;
+};
+
+&sai2 {
+ clocks = <&sai2_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai2_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_2>;
+};
+
+&sai3 {
+ clocks = <&sai3_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai3_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_3>;
+};
+
+&asrc1 {
+ clocks = <&asrc1_lpcg IMX_LPCG_CLK_0>,
+ <&asrc1_lpcg IMX_LPCG_CLK_2>,
+ <&aud_pll_div0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>,
+ <&acm IMX_ADMA_ACM_AUD_CLK0_SEL>,
+ <&acm IMX_ADMA_ACM_AUD_CLK1_SEL>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_ASRC_1>;
+};
+
+&amix {
+ dais = <&sai6>, <&sai7>;
+};
+
+&asrc0_lpcg {
+ clocks = <&audio_ipg_clk>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>;
+ clock-output-names = "asrc0_lpcg_ipg_clk", "asrc0_lpcg_mem_clk";
+};
+
+&esai0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "esai0_lpcg_extal_clk", "esai0_lpcg_ipg_clk";
+};
+
+&spdif0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_5>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "spdif0_lpcg_tx_clk", "spdif0_lpcg_gclkw";
+};
+
+&sai0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai0_lpcg_mclk", "sai0_lpcg_ipg_clk";
+};
+
+&sai1_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai1_lpcg_mclk", "sai1_lpcg_ipg_clk";
+};
+
+&sai2_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai2_lpcg_mclk", "sai2_lpcg_ipg_clk";
+};
+
+&sai3_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai3_lpcg_mclk", "sai3_lpcg_ipg_clk";
+};
+
+&asrc1_lpcg {
+ clocks = <&audio_ipg_clk>, <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>;
+ clock-output-names = "asrc1_lpcg_ipg_clk", "asrc1_lpcg_mem_clk";
+};
+
+&mqs0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "mqs0_lpcg_mclk", "mqs0_lpcg_ipg_clk";
+};
+
+&dsp_lpcg {
+ status = "disabled";
+};
+
+&dsp_ram_lpcg {
+ status = "disabled";
+};
+
+&audio_subsys {
+
+ acm: acm@59e00000 {
+ compatible = "fsl,imx8qm-acm";
+ reg = <0x59e00000 0x1D0000>;
+ #clock-cells = <1>;
+ power-domains = <&pd IMX_SC_R_AUDIO_CLK_0>,
+ <&pd IMX_SC_R_AUDIO_CLK_1>,
+ <&pd IMX_SC_R_MCLK_OUT_0>,
+ <&pd IMX_SC_R_MCLK_OUT_1>,
+ <&pd IMX_SC_R_AUDIO_PLL_0>,
+ <&pd IMX_SC_R_AUDIO_PLL_1>,
+ <&pd IMX_SC_R_ASRC_0>,
+ <&pd IMX_SC_R_ASRC_1>,
+ <&pd IMX_SC_R_ESAI_0>,
+ <&pd IMX_SC_R_ESAI_1>,
+ <&pd IMX_SC_R_SAI_0>,
+ <&pd IMX_SC_R_SAI_1>,
+ <&pd IMX_SC_R_SAI_2>,
+ <&pd IMX_SC_R_SAI_3>,
+ <&pd IMX_SC_R_SAI_4>,
+ <&pd IMX_SC_R_SAI_5>,
+ <&pd IMX_SC_R_SAI_6>,
+ <&pd IMX_SC_R_SAI_7>,
+ <&pd IMX_SC_R_SPDIF_0>,
+ <&pd IMX_SC_R_SPDIF_1>,
+ <&pd IMX_SC_R_MQS_0>;
+ clocks = <&aud_rec0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_rec1_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>,
+ <&clk_mlb_clk>,
+ <&clk_hdmi_rx_mclk>,
+ <&clk_ext_aud_mclk0>,
+ <&clk_ext_aud_mclk1>,
+ <&clk_esai0_rx_clk>,
+ <&clk_esai0_rx_hf_clk>,
+ <&clk_esai0_tx_clk>,
+ <&clk_esai0_tx_hf_clk>,
+ <&clk_esai1_rx_clk>,
+ <&clk_esai1_rx_hf_clk>,
+ <&clk_esai1_tx_clk>,
+ <&clk_esai1_tx_hf_clk>,
+ <&clk_spdif0_rx>,
+ <&clk_spdif0_rx>,
+ <&clk_sai0_rx_bclk>,
+ <&clk_sai0_tx_bclk>,
+ <&clk_sai1_rx_bclk>,
+ <&clk_sai1_tx_bclk>,
+ <&clk_sai2_rx_bclk>,
+ <&clk_sai3_rx_bclk>,
+ <&clk_sai4_rx_bclk>,
+ <&clk_sai5_rx_bclk>,
+ <&clk_sai6_rx_bclk>;
+ clock-names = "aud_rec_clk0_lpcg_clk",
+ "aud_rec_clk1_lpcg_clk",
+ "aud_pll_div_clk0_lpcg_clk",
+ "aud_pll_div_clk1_lpcg_clk",
+ "mlb_clk",
+ "hdmi_rx_mclk",
+ "ext_aud_mclk0",
+ "ext_aud_mclk1",
+ "esai0_rx_clk",
+ "esai0_rx_hf_clk",
+ "esai0_tx_clk",
+ "esai0_tx_hf_clk",
+ "esai1_rx_clk",
+ "esai1_rx_hf_clk",
+ "esai1_tx_clk",
+ "esai1_tx_hf_clk",
+ "spdif0_rx",
+ "spdif1_rx",
+ "sai0_rx_bclk",
+ "sai0_tx_bclk",
+ "sai1_rx_bclk",
+ "sai1_tx_bclk",
+ "sai2_rx_bclk",
+ "sai3_rx_bclk",
+ "sai4_rx_bclk",
+ "sai5_tx_bclk",
+ "sai6_rx_bclk";
+ };
+
+ sai4: sai@59080000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59080000 0x10000>;
+ interrupts = <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai4_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai4_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "rx";
+ dmas = <&edma0 18 0 1>;
+ fsl,dataline = <0 0xf 0x0>;
+ power-domains = <&pd IMX_SC_R_SAI_4>;
+ status = "disabled";
+ };
+
+ sai5: sai@59090000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59090000 0x10000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai5_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai5_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx";
+ dmas = <&edma0 19 0 0>;
+ fsl,dataline = <0 0x0 0xf>;
+ power-domains = <&pd IMX_SC_R_SAI_5>;
+ status = "disabled";
+ };
+
+ esai1: esai@59810000 {
+ compatible = "fsl,imx8qm-esai";
+ reg = <0x59810000 0x10000>;
+ interrupts = <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&esai1_lpcg IMX_LPCG_CLK_0>,
+ <&esai1_lpcg IMX_LPCG_CLK_4>,
+ <&esai1_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>;
+ clock-names = "core", "extal", "fsys", "spba";
+ dmas = <&edma1 6 0 1>, <&edma1 7 0 0>;
+ dma-names = "rx", "tx";
+ power-domains = <&pd IMX_SC_R_ESAI_1>;
+ status = "disabled";
+ };
+
+ sai6: sai@59820000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59820000 0x10000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai6_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai6_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "rx", "tx";
+ dmas = <&edma1 8 0 1>, <&edma1 9 0 0>;
+ power-domains = <&pd IMX_SC_R_SAI_6>;
+ status = "disabled";
+ };
+
+ sai7: sai@59830000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59830000 0x10000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai7_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai7_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx";
+ dmas = <&edma1 10 0 0>;
+ power-domains = <&pd IMX_SC_R_SAI_7>;
+ status = "disabled";
+ };
+
+ sai4_lpcg: clock-controller@59480000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59480000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI4_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai4_lpcg_mclk", "sai4_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_4>;
+ status = "disabled";
+ };
+
+ sai5_lpcg: clock-controller@59490000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59490000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI5_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai5_lpcg_mclk", "sai5_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_5>;
+ status = "disabled";
+ };
+
+ esai1_lpcg: clock-controller@59c10000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59c10000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_ESAI1_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "esai1_lpcg_extal_clk", "esai1_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_ESAI_1>;
+ };
+
+ sai6_lpcg: clock-controller@59c20000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59c20000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI6_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai6_lpcg_mclk", "sai6_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_6>;
+ };
+
+ sai7_lpcg: clock-controller@59c30000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59c30000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI7_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai7_lpcg_mclk", "sai7_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_7>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index b3d01677b70c4..da49d4bad32ee 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -461,7 +461,92 @@ drc_crit0: trip1 {
};
};
+ clk_dummy: clock-dummy {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "clk_dummy";
+ };
+
+ clk_mlb_clk: clock-mlb-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "mlb_clk";
+ };
+
+ clk_esai1_rx_clk: clock-esai1-rx {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_rx_clk";
+ };
+
+ clk_esai1_rx_hf_clk: clock-esai1-rx-hf {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_rx_hf_clk";
+ };
+
+ clk_esai1_tx_clk: clock-esai1-tx {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_tx_clk";
+ };
+
+ clk_esai1_tx_hf_clk: clock-esai1-tx-hf {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_tx_hf_clk";
+ };
+
+ clk_spdif1_rx: clock-spdif1-rx {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "spdif1_rx";
+ };
+
+ clk_sai5_rx_bclk: clock-sai5-rx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai5_rx_bclk";
+ };
+
+ clk_sai5_tx_bclk: clock-sai5-tx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai5_tx_bclk";
+ };
+
+ clk_sai6_rx_bclk: clock-sai6-rx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai6_rx_bclk";
+ };
+
+ clk_sai6_tx_bclk: clock-sai6-tx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai6_tx_bclk";
+ };
+
+ clk_hdmi_rx_mclk: clock-hdmi-rx-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "hdmi-rx-mclk";
+ };
+
/* sorted in register address */
+ #include "imx8-ss-audio.dtsi"
#include "imx8-ss-vpu.dtsi"
#include "imx8-ss-img.dtsi"
#include "imx8-ss-dma.dtsi"
@@ -473,3 +558,4 @@ drc_crit0: trip1 {
#include "imx8qm-ss-dma.dtsi"
#include "imx8qm-ss-conn.dtsi"
#include "imx8qm-ss-lsio.dtsi"
+#include "imx8qm-ss-audio.dtsi"
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 02/10] arm64: dts: imx8qm-ss-audio: add audio nodes
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add i.MX8QM audio related nodes and update eDMA[0,1]'s information.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi | 473 +++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 86 ++++
2 files changed, 559 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi
new file mode 100644
index 0000000000000..ed5a1b4af1d76
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-audio.dtsi
@@ -0,0 +1,473 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ * Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+/delete-node/ &acm;
+/delete-node/ &sai4;
+/delete-node/ &sai5;
+/delete-node/ &sai4_lpcg;
+/delete-node/ &sai5_lpcg;
+
+/* edma2 called in imx8qm RM with the same address in edma0 of imx8qxp */
+&edma0{
+ reg = <0x591f0000 0x150000>;
+ dma-channels = <20>;
+ dma-channel-mask = <0>;
+ interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>, /* asrc0 */
+ <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>, /* esai0 */
+ <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>, /* spdif0 */
+ <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>, /* spdif1 */
+ <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, /* sai0 */
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, /* sai1 */
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, /* sai2 */
+ <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, /* sai3 */
+ <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, /* sai4 */
+ <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>; /* sai5 */
+ power-domains = <&pd IMX_SC_R_DMA_2_CH0>,
+ <&pd IMX_SC_R_DMA_2_CH1>,
+ <&pd IMX_SC_R_DMA_2_CH2>,
+ <&pd IMX_SC_R_DMA_2_CH3>,
+ <&pd IMX_SC_R_DMA_2_CH4>,
+ <&pd IMX_SC_R_DMA_2_CH5>,
+ <&pd IMX_SC_R_DMA_2_CH6>,
+ <&pd IMX_SC_R_DMA_2_CH7>,
+ <&pd IMX_SC_R_DMA_2_CH8>,
+ <&pd IMX_SC_R_DMA_2_CH9>,
+ <&pd IMX_SC_R_DMA_2_CH10>,
+ <&pd IMX_SC_R_DMA_2_CH11>,
+ <&pd IMX_SC_R_DMA_2_CH12>,
+ <&pd IMX_SC_R_DMA_2_CH13>,
+ <&pd IMX_SC_R_DMA_2_CH14>,
+ <&pd IMX_SC_R_DMA_2_CH15>,
+ <&pd IMX_SC_R_DMA_2_CH16>,
+ <&pd IMX_SC_R_DMA_2_CH17>,
+ <&pd IMX_SC_R_DMA_2_CH18>,
+ <&pd IMX_SC_R_DMA_2_CH19>;
+};
+
+/* edma3 called in imx8qm RM with the same address in edma1 of imx8qxp */
+&edma1{
+ reg = <0x599F0000 0xc0000>;
+ dma-channels = <11>;
+ dma-channel-mask = <0xc0>;
+ interrupts = <GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>, /* asrc1 */
+ <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, /* no used */
+ <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, /* no used */
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, /* sai6 */
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>; /* sai7 */
+ power-domains = <&pd IMX_SC_R_DMA_3_CH0>,
+ <&pd IMX_SC_R_DMA_3_CH1>,
+ <&pd IMX_SC_R_DMA_3_CH2>,
+ <&pd IMX_SC_R_DMA_3_CH3>,
+ <&pd IMX_SC_R_DMA_3_CH4>,
+ <&pd IMX_SC_R_DMA_3_CH5>,
+ <&pd IMX_SC_R_DMA_3_CH6>,
+ <&pd IMX_SC_R_DMA_3_CH7>,
+ <&pd IMX_SC_R_DMA_3_CH8>,
+ <&pd IMX_SC_R_DMA_3_CH9>,
+ <&pd IMX_SC_R_DMA_3_CH10>;
+};
+
+&asrc0 {
+ clocks = <&asrc0_lpcg IMX_LPCG_CLK_0>,
+ <&asrc0_lpcg IMX_LPCG_CLK_2>,
+ <&aud_pll_div0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>,
+ <&acm IMX_ADMA_ACM_AUD_CLK0_SEL>,
+ <&acm IMX_ADMA_ACM_AUD_CLK1_SEL>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_ASRC_0>;
+};
+
+&esai0 {
+ clocks = <&esai0_lpcg IMX_LPCG_CLK_0>,
+ <&esai0_lpcg IMX_LPCG_CLK_4>,
+ <&esai0_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_ESAI_0>;
+};
+
+&spdif0 {
+ clocks = <&spdif0_lpcg IMX_LPCG_CLK_4>, /* core */
+ <&clk_dummy>, /* rxtx0 */
+ <&spdif0_lpcg IMX_LPCG_CLK_5>, /* rxtx1 */
+ <&clk_dummy>, /* rxtx2 */
+ <&clk_dummy>, /* rxtx3 */
+ <&clk_dummy>, /* rxtx4 */
+ <&audio_ipg_clk>, /* rxtx5 */
+ <&clk_dummy>, /* rxtx6 */
+ <&clk_dummy>, /* rxtx7 */
+ <&clk_dummy>; /* spba */
+ power-domains = <&pd IMX_SC_R_SPDIF_0>;
+};
+
+&sai0 {
+ clocks = <&sai0_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai0_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_0>;
+};
+
+&sai1 {
+ clocks = <&sai1_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai1_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_1>;
+};
+
+&sai2 {
+ clocks = <&sai2_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai2_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_2>;
+};
+
+&sai3 {
+ clocks = <&sai3_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai3_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_SAI_3>;
+};
+
+&asrc1 {
+ clocks = <&asrc1_lpcg IMX_LPCG_CLK_0>,
+ <&asrc1_lpcg IMX_LPCG_CLK_2>,
+ <&aud_pll_div0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>,
+ <&acm IMX_ADMA_ACM_AUD_CLK0_SEL>,
+ <&acm IMX_ADMA_ACM_AUD_CLK1_SEL>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ power-domains = <&pd IMX_SC_R_ASRC_1>;
+};
+
+&amix {
+ dais = <&sai6>, <&sai7>;
+};
+
+&asrc0_lpcg {
+ clocks = <&audio_ipg_clk>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>;
+ clock-output-names = "asrc0_lpcg_ipg_clk", "asrc0_lpcg_mem_clk";
+};
+
+&esai0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "esai0_lpcg_extal_clk", "esai0_lpcg_ipg_clk";
+};
+
+&spdif0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_5>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "spdif0_lpcg_tx_clk", "spdif0_lpcg_gclkw";
+};
+
+&sai0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai0_lpcg_mclk", "sai0_lpcg_ipg_clk";
+};
+
+&sai1_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai1_lpcg_mclk", "sai1_lpcg_ipg_clk";
+};
+
+&sai2_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai2_lpcg_mclk", "sai2_lpcg_ipg_clk";
+};
+
+&sai3_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai3_lpcg_mclk", "sai3_lpcg_ipg_clk";
+};
+
+&asrc1_lpcg {
+ clocks = <&audio_ipg_clk>, <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>;
+ clock-output-names = "asrc1_lpcg_ipg_clk", "asrc1_lpcg_mem_clk";
+};
+
+&mqs0_lpcg {
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "mqs0_lpcg_mclk", "mqs0_lpcg_ipg_clk";
+};
+
+&dsp_lpcg {
+ status = "disabled";
+};
+
+&dsp_ram_lpcg {
+ status = "disabled";
+};
+
+&audio_subsys {
+
+ acm: acm@59e00000 {
+ compatible = "fsl,imx8qm-acm";
+ reg = <0x59e00000 0x1D0000>;
+ #clock-cells = <1>;
+ power-domains = <&pd IMX_SC_R_AUDIO_CLK_0>,
+ <&pd IMX_SC_R_AUDIO_CLK_1>,
+ <&pd IMX_SC_R_MCLK_OUT_0>,
+ <&pd IMX_SC_R_MCLK_OUT_1>,
+ <&pd IMX_SC_R_AUDIO_PLL_0>,
+ <&pd IMX_SC_R_AUDIO_PLL_1>,
+ <&pd IMX_SC_R_ASRC_0>,
+ <&pd IMX_SC_R_ASRC_1>,
+ <&pd IMX_SC_R_ESAI_0>,
+ <&pd IMX_SC_R_ESAI_1>,
+ <&pd IMX_SC_R_SAI_0>,
+ <&pd IMX_SC_R_SAI_1>,
+ <&pd IMX_SC_R_SAI_2>,
+ <&pd IMX_SC_R_SAI_3>,
+ <&pd IMX_SC_R_SAI_4>,
+ <&pd IMX_SC_R_SAI_5>,
+ <&pd IMX_SC_R_SAI_6>,
+ <&pd IMX_SC_R_SAI_7>,
+ <&pd IMX_SC_R_SPDIF_0>,
+ <&pd IMX_SC_R_SPDIF_1>,
+ <&pd IMX_SC_R_MQS_0>;
+ clocks = <&aud_rec0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_rec1_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div0_lpcg IMX_LPCG_CLK_0>,
+ <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>,
+ <&clk_mlb_clk>,
+ <&clk_hdmi_rx_mclk>,
+ <&clk_ext_aud_mclk0>,
+ <&clk_ext_aud_mclk1>,
+ <&clk_esai0_rx_clk>,
+ <&clk_esai0_rx_hf_clk>,
+ <&clk_esai0_tx_clk>,
+ <&clk_esai0_tx_hf_clk>,
+ <&clk_esai1_rx_clk>,
+ <&clk_esai1_rx_hf_clk>,
+ <&clk_esai1_tx_clk>,
+ <&clk_esai1_tx_hf_clk>,
+ <&clk_spdif0_rx>,
+ <&clk_spdif0_rx>,
+ <&clk_sai0_rx_bclk>,
+ <&clk_sai0_tx_bclk>,
+ <&clk_sai1_rx_bclk>,
+ <&clk_sai1_tx_bclk>,
+ <&clk_sai2_rx_bclk>,
+ <&clk_sai3_rx_bclk>,
+ <&clk_sai4_rx_bclk>,
+ <&clk_sai5_rx_bclk>,
+ <&clk_sai6_rx_bclk>;
+ clock-names = "aud_rec_clk0_lpcg_clk",
+ "aud_rec_clk1_lpcg_clk",
+ "aud_pll_div_clk0_lpcg_clk",
+ "aud_pll_div_clk1_lpcg_clk",
+ "mlb_clk",
+ "hdmi_rx_mclk",
+ "ext_aud_mclk0",
+ "ext_aud_mclk1",
+ "esai0_rx_clk",
+ "esai0_rx_hf_clk",
+ "esai0_tx_clk",
+ "esai0_tx_hf_clk",
+ "esai1_rx_clk",
+ "esai1_rx_hf_clk",
+ "esai1_tx_clk",
+ "esai1_tx_hf_clk",
+ "spdif0_rx",
+ "spdif1_rx",
+ "sai0_rx_bclk",
+ "sai0_tx_bclk",
+ "sai1_rx_bclk",
+ "sai1_tx_bclk",
+ "sai2_rx_bclk",
+ "sai3_rx_bclk",
+ "sai4_rx_bclk",
+ "sai5_tx_bclk",
+ "sai6_rx_bclk";
+ };
+
+ sai4: sai@59080000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59080000 0x10000>;
+ interrupts = <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai4_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai4_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "rx";
+ dmas = <&edma0 18 0 1>;
+ fsl,dataline = <0 0xf 0x0>;
+ power-domains = <&pd IMX_SC_R_SAI_4>;
+ status = "disabled";
+ };
+
+ sai5: sai@59090000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59090000 0x10000>;
+ interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai5_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai5_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx";
+ dmas = <&edma0 19 0 0>;
+ fsl,dataline = <0 0x0 0xf>;
+ power-domains = <&pd IMX_SC_R_SAI_5>;
+ status = "disabled";
+ };
+
+ esai1: esai@59810000 {
+ compatible = "fsl,imx8qm-esai";
+ reg = <0x59810000 0x10000>;
+ interrupts = <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&esai1_lpcg IMX_LPCG_CLK_0>,
+ <&esai1_lpcg IMX_LPCG_CLK_4>,
+ <&esai1_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>;
+ clock-names = "core", "extal", "fsys", "spba";
+ dmas = <&edma1 6 0 1>, <&edma1 7 0 0>;
+ dma-names = "rx", "tx";
+ power-domains = <&pd IMX_SC_R_ESAI_1>;
+ status = "disabled";
+ };
+
+ sai6: sai@59820000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59820000 0x10000>;
+ interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai6_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai6_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "rx", "tx";
+ dmas = <&edma1 8 0 1>, <&edma1 9 0 0>;
+ power-domains = <&pd IMX_SC_R_SAI_6>;
+ status = "disabled";
+ };
+
+ sai7: sai@59830000 {
+ compatible = "fsl,imx8qm-sai";
+ reg = <0x59830000 0x10000>;
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sai7_lpcg IMX_LPCG_CLK_0>,
+ <&clk_dummy>,
+ <&sai7_lpcg IMX_LPCG_CLK_4>,
+ <&clk_dummy>,
+ <&clk_dummy>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+ dma-names = "tx";
+ dmas = <&edma1 10 0 0>;
+ power-domains = <&pd IMX_SC_R_SAI_7>;
+ status = "disabled";
+ };
+
+ sai4_lpcg: clock-controller@59480000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59480000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI4_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai4_lpcg_mclk", "sai4_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_4>;
+ status = "disabled";
+ };
+
+ sai5_lpcg: clock-controller@59490000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59490000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI5_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai5_lpcg_mclk", "sai5_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_5>;
+ status = "disabled";
+ };
+
+ esai1_lpcg: clock-controller@59c10000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59c10000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_ESAI1_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "esai1_lpcg_extal_clk", "esai1_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_ESAI_1>;
+ };
+
+ sai6_lpcg: clock-controller@59c20000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59c20000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI6_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai6_lpcg_mclk", "sai6_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_6>;
+ };
+
+ sai7_lpcg: clock-controller@59c30000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x59c30000 0x10000>;
+ #clock-cells = <1>;
+ clocks = <&acm IMX_ADMA_ACM_SAI7_MCLK_SEL>,
+ <&audio_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_0>;
+ clock-output-names = "sai7_lpcg_mclk", "sai7_lpcg_ipg_clk";
+ power-domains = <&pd IMX_SC_R_SAI_7>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index b3d01677b70c4..da49d4bad32ee 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -461,7 +461,92 @@ drc_crit0: trip1 {
};
};
+ clk_dummy: clock-dummy {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "clk_dummy";
+ };
+
+ clk_mlb_clk: clock-mlb-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "mlb_clk";
+ };
+
+ clk_esai1_rx_clk: clock-esai1-rx {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_rx_clk";
+ };
+
+ clk_esai1_rx_hf_clk: clock-esai1-rx-hf {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_rx_hf_clk";
+ };
+
+ clk_esai1_tx_clk: clock-esai1-tx {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_tx_clk";
+ };
+
+ clk_esai1_tx_hf_clk: clock-esai1-tx-hf {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "esai1_tx_hf_clk";
+ };
+
+ clk_spdif1_rx: clock-spdif1-rx {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "spdif1_rx";
+ };
+
+ clk_sai5_rx_bclk: clock-sai5-rx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai5_rx_bclk";
+ };
+
+ clk_sai5_tx_bclk: clock-sai5-tx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai5_tx_bclk";
+ };
+
+ clk_sai6_rx_bclk: clock-sai6-rx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai6_rx_bclk";
+ };
+
+ clk_sai6_tx_bclk: clock-sai6-tx-bclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "sai6_tx_bclk";
+ };
+
+ clk_hdmi_rx_mclk: clock-hdmi-rx-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "hdmi-rx-mclk";
+ };
+
/* sorted in register address */
+ #include "imx8-ss-audio.dtsi"
#include "imx8-ss-vpu.dtsi"
#include "imx8-ss-img.dtsi"
#include "imx8-ss-dma.dtsi"
@@ -473,3 +558,4 @@ drc_crit0: trip1 {
#include "imx8qm-ss-dma.dtsi"
#include "imx8qm-ss-conn.dtsi"
#include "imx8qm-ss-lsio.dtsi"
+#include "imx8qm-ss-audio.dtsi"
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 03/10] arm64: dts: imx8qm-mek: add sai and wm8960 support
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add sai[0,1,6,7], wm8960 and asrc0 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 140 +++++++++++++++++++++++++++
1 file changed, 140 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 5c6b39c6933fc..9f8d3df00f793 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -46,6 +46,47 @@ reg_vref_1v8: regulator-adc-vref {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
+ bt_sco_codec: bt_sco_codec {
+ #sound-dai-cells = <1>;
+ compatible = "linux,bt-sco";
+ };
+
+ sound-bt-sco {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "bt-sco-audio";
+ simple-audio-card,format = "dsp_a";
+ simple-audio-card,bitclock-inversion;
+ simple-audio-card,frame-master = <&btcpu>;
+ simple-audio-card,bitclock-master = <&btcpu>;
+
+ btcpu: simple-audio-card,cpu {
+ sound-dai = <&sai0>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&bt_sco_codec 1>;
+ };
+ };
+
+ sound-wm8960 {
+ compatible = "fsl,imx-audio-wm8960";
+ model = "wm8960-audio";
+ audio-cpu = <&sai1>;
+ audio-codec = <&wm8960>;
+ hp-det-gpio = <&lsio_gpio0 31 GPIO_ACTIVE_HIGH>;
+ audio-routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Ext Spk", "SPK_LP",
+ "Ext Spk", "SPK_LN",
+ "Ext Spk", "SPK_RP",
+ "Ext Spk", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "Mic Jack", "MICB";
+ };
};
&adc0 {
@@ -65,6 +106,77 @@ &i2c1 {
scl-gpios = <&lsio_gpio0 14 GPIO_ACTIVE_HIGH>;
sda-gpios = <&lsio_gpio0 15 GPIO_ACTIVE_HIGH>;
status = "okay";
+
+ wm8960: audio-codec@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ clock-names = "mclk";
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <12288000>;
+ wlf,shared-lrclk;
+ wlf,hp-cfg = <2 2 3>;
+ wlf,gpio-cfg = <1 3>;
+ };
+};
+
+&asrc0 {
+ fsl,asrc-rate = <48000>;
+ status = "okay";
+};
+
+&amix {
+ status = "okay";
+};
+
+&sai0 {
+ #sound-dai-cells = <0>;
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai0_lpcg IMX_LPCG_CLK_4>;
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai0>;
+ status = "okay";
+};
+
+&sai1 {
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai1_lpcg IMX_LPCG_CLK_4>; /* FIXME: should be sai1, original code is 0 */
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ status = "okay";
+};
+
+&sai6 {
+ assigned-clocks = <&acm IMX_ADMA_ACM_SAI6_MCLK_SEL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai6_lpcg IMX_LPCG_CLK_4>;
+ assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+ fsl,sai-asynchronous;
+ status = "okay";
+};
+
+&sai7 {
+ assigned-clocks = <&acm IMX_ADMA_ACM_SAI7_MCLK_SEL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai7_lpcg IMX_LPCG_CLK_4>;
+ assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+ fsl,sai-asynchronous;
+ status = "okay";
};
&lpuart0 {
@@ -161,6 +273,16 @@ &usdhc2 {
};
&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0 0x0600004c
+ IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x0600004c
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x0600004c
@@ -256,6 +378,24 @@ IMX8QM_M41_GPIO0_01_DMA_UART3_TX 0x06000020
>;
};
+ pinctrl_sai0: sai0grp {
+ fsl,pins = <
+ IMX8QM_SPI0_CS1_AUD_SAI0_TXC 0x0600004c
+ IMX8QM_SPI2_CS1_AUD_SAI0_TXFS 0x0600004c
+ IMX8QM_SAI1_RXFS_AUD_SAI0_RXD 0x0600004c
+ IMX8QM_SAI1_RXC_AUD_SAI0_TXD 0x0600006c
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ IMX8QM_SAI1_RXD_AUD_SAI1_RXD 0x06000040
+ IMX8QM_SAI1_TXFS_AUD_SAI1_TXFS 0x06000040
+ IMX8QM_SAI1_TXD_AUD_SAI1_TXD 0x06000060
+ IMX8QM_SAI1_TXC_AUD_SAI1_TXC 0x06000040
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 03/10] arm64: dts: imx8qm-mek: add sai and wm8960 support
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add sai[0,1,6,7], wm8960 and asrc0 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 140 +++++++++++++++++++++++++++
1 file changed, 140 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 5c6b39c6933fc..9f8d3df00f793 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -46,6 +46,47 @@ reg_vref_1v8: regulator-adc-vref {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
+
+ bt_sco_codec: bt_sco_codec {
+ #sound-dai-cells = <1>;
+ compatible = "linux,bt-sco";
+ };
+
+ sound-bt-sco {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "bt-sco-audio";
+ simple-audio-card,format = "dsp_a";
+ simple-audio-card,bitclock-inversion;
+ simple-audio-card,frame-master = <&btcpu>;
+ simple-audio-card,bitclock-master = <&btcpu>;
+
+ btcpu: simple-audio-card,cpu {
+ sound-dai = <&sai0>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <16>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&bt_sco_codec 1>;
+ };
+ };
+
+ sound-wm8960 {
+ compatible = "fsl,imx-audio-wm8960";
+ model = "wm8960-audio";
+ audio-cpu = <&sai1>;
+ audio-codec = <&wm8960>;
+ hp-det-gpio = <&lsio_gpio0 31 GPIO_ACTIVE_HIGH>;
+ audio-routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Ext Spk", "SPK_LP",
+ "Ext Spk", "SPK_LN",
+ "Ext Spk", "SPK_RP",
+ "Ext Spk", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "Mic Jack", "MICB";
+ };
};
&adc0 {
@@ -65,6 +106,77 @@ &i2c1 {
scl-gpios = <&lsio_gpio0 14 GPIO_ACTIVE_HIGH>;
sda-gpios = <&lsio_gpio0 15 GPIO_ACTIVE_HIGH>;
status = "okay";
+
+ wm8960: audio-codec@1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ clocks = <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ clock-names = "mclk";
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&mclkout0_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <12288000>;
+ wlf,shared-lrclk;
+ wlf,hp-cfg = <2 2 3>;
+ wlf,gpio-cfg = <1 3>;
+ };
+};
+
+&asrc0 {
+ fsl,asrc-rate = <48000>;
+ status = "okay";
+};
+
+&amix {
+ status = "okay";
+};
+
+&sai0 {
+ #sound-dai-cells = <0>;
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai0_lpcg IMX_LPCG_CLK_4>;
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai0>;
+ status = "okay";
+};
+
+&sai1 {
+ assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai1_lpcg IMX_LPCG_CLK_4>; /* FIXME: should be sai1, original code is 0 */
+ assigned-clock-rates = <786432000>, <49152000>, <12288000>, <49152000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ status = "okay";
+};
+
+&sai6 {
+ assigned-clocks = <&acm IMX_ADMA_ACM_SAI6_MCLK_SEL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai6_lpcg IMX_LPCG_CLK_4>;
+ assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+ fsl,sai-asynchronous;
+ status = "okay";
+};
+
+&sai7 {
+ assigned-clocks = <&acm IMX_ADMA_ACM_SAI7_MCLK_SEL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+ <&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+ <&sai7_lpcg IMX_LPCG_CLK_4>;
+ assigned-clock-parents = <&aud_pll_div1_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <0>, <786432000>, <98304000>, <12288000>, <98304000>;
+ fsl,sai-asynchronous;
+ status = "okay";
};
&lpuart0 {
@@ -161,6 +273,16 @@ &usdhc2 {
};
&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ IMX8QM_MCLK_OUT0_AUD_ACM_MCLK_OUT0 0x0600004c
+ IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x0600004c
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x0600004c
@@ -256,6 +378,24 @@ IMX8QM_M41_GPIO0_01_DMA_UART3_TX 0x06000020
>;
};
+ pinctrl_sai0: sai0grp {
+ fsl,pins = <
+ IMX8QM_SPI0_CS1_AUD_SAI0_TXC 0x0600004c
+ IMX8QM_SPI2_CS1_AUD_SAI0_TXFS 0x0600004c
+ IMX8QM_SAI1_RXFS_AUD_SAI0_RXD 0x0600004c
+ IMX8QM_SAI1_RXC_AUD_SAI0_TXD 0x0600006c
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ IMX8QM_SAI1_RXD_AUD_SAI1_RXD 0x06000040
+ IMX8QM_SAI1_TXFS_AUD_SAI1_TXFS 0x06000040
+ IMX8QM_SAI1_TXD_AUD_SAI1_TXD 0x06000060
+ IMX8QM_SAI1_TXC_AUD_SAI1_TXC 0x06000040
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 04/10] arm64: dts: imx8x: add cm41 subsystem dtsi
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add cm41 subsystem dtsi for iMX8X chips.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi | 68 +++++++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 1 +
2 files changed, 69 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi
new file mode 100644
index 0000000000000..d715f2a6b0378
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ * Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+#include <dt-bindings/firmware/imx/rsrc.h>
+#include <dt-bindings/clock/imx8-lpcg.h>
+
+cm41_ipg_clk: clock-cm41-ipg {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <132000000>;
+ clock-output-names = "cm41_ipg_clk";
+};
+
+cm41_subsys: bus@38000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x38000000 0x0 0x38000000 0x4000000>;
+ interrupt-parent = <&cm41_intmux>;
+
+ cm41_i2c: i2c@3b230000 {
+ compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x3b230000 0x1000>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cm41_i2c_lpcg IMX_LPCG_CLK_0>,
+ <&cm41_i2c_lpcg IMX_LPCG_CLK_4>;
+ clock-names = "per", "ipg";
+ assigned-clocks = <&clk IMX_SC_R_M4_1_I2C IMX_SC_PM_CLK_PER>;
+ assigned-clock-rates = <24000000>;
+ power-domains = <&pd IMX_SC_R_M4_1_I2C>;
+ status = "disabled";
+ };
+
+ cm41_intmux: intmux@3b400000 {
+ compatible = "fsl,imx-intmux";
+ reg = <0x3b400000 0x1000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&cm41_ipg_clk>;
+ clock-names = "ipg";
+ power-domains = <&pd IMX_SC_R_M4_1_INTMUX>;
+ status = "disabled";
+ };
+
+ cm41_i2c_lpcg: clock-controller@3b630000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x3b630000 0x1000>;
+ #clock-cells = <1>;
+ clocks = <&clk IMX_SC_R_M4_1_I2C IMX_SC_PM_CLK_PER>,
+ <&cm41_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "cm41_lpcg_i2c_clk",
+ "cm41_lpcg_i2c_ipg_clk";
+ power-domains = <&pd IMX_SC_R_M4_1_I2C>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index da49d4bad32ee..96a940c6046d8 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -546,6 +546,7 @@ clk_hdmi_rx_mclk: clock-hdmi-rx-mclk {
};
/* sorted in register address */
+ #include "imx8-ss-cm41.dtsi"
#include "imx8-ss-audio.dtsi"
#include "imx8-ss-vpu.dtsi"
#include "imx8-ss-img.dtsi"
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 04/10] arm64: dts: imx8x: add cm41 subsystem dtsi
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add cm41 subsystem dtsi for iMX8X chips.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi | 68 +++++++++++++++++++++++++
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 1 +
2 files changed, 69 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi
new file mode 100644
index 0000000000000..d715f2a6b0378
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-cm41.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 NXP
+ * Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+#include <dt-bindings/firmware/imx/rsrc.h>
+#include <dt-bindings/clock/imx8-lpcg.h>
+
+cm41_ipg_clk: clock-cm41-ipg {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <132000000>;
+ clock-output-names = "cm41_ipg_clk";
+};
+
+cm41_subsys: bus@38000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x38000000 0x0 0x38000000 0x4000000>;
+ interrupt-parent = <&cm41_intmux>;
+
+ cm41_i2c: i2c@3b230000 {
+ compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x3b230000 0x1000>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cm41_i2c_lpcg IMX_LPCG_CLK_0>,
+ <&cm41_i2c_lpcg IMX_LPCG_CLK_4>;
+ clock-names = "per", "ipg";
+ assigned-clocks = <&clk IMX_SC_R_M4_1_I2C IMX_SC_PM_CLK_PER>;
+ assigned-clock-rates = <24000000>;
+ power-domains = <&pd IMX_SC_R_M4_1_I2C>;
+ status = "disabled";
+ };
+
+ cm41_intmux: intmux@3b400000 {
+ compatible = "fsl,imx-intmux";
+ reg = <0x3b400000 0x1000>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&cm41_ipg_clk>;
+ clock-names = "ipg";
+ power-domains = <&pd IMX_SC_R_M4_1_INTMUX>;
+ status = "disabled";
+ };
+
+ cm41_i2c_lpcg: clock-controller@3b630000 {
+ compatible = "fsl,imx8qxp-lpcg";
+ reg = <0x3b630000 0x1000>;
+ #clock-cells = <1>;
+ clocks = <&clk IMX_SC_R_M4_1_I2C IMX_SC_PM_CLK_PER>,
+ <&cm41_ipg_clk>;
+ clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>;
+ clock-output-names = "cm41_lpcg_i2c_clk",
+ "cm41_lpcg_i2c_ipg_clk";
+ power-domains = <&pd IMX_SC_R_M4_1_I2C>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index da49d4bad32ee..96a940c6046d8 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -546,6 +546,7 @@ clk_hdmi_rx_mclk: clock-hdmi-rx-mclk {
};
/* sorted in register address */
+ #include "imx8-ss-cm41.dtsi"
#include "imx8-ss-audio.dtsi"
#include "imx8-ss-vpu.dtsi"
#include "imx8-ss-img.dtsi"
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 05/10] arm64: dts: imx8qm-mek: add i2c0 and children devices
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add i2c0 and all devices under it for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 50 ++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 9f8d3df00f793..e5740f301bde0 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -96,6 +96,49 @@ &adc0 {
status = "okay";
};
+&i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ status = "okay";
+
+ lsm303arg@19 {
+ compatible = "st,lsm303agr-accel";
+ reg = <0x19>;
+ };
+
+ fxas21002c@20 {
+ compatible = "nxp,fxas21002c";
+ reg = <0x20>;
+ };
+
+ isl29023@44 {
+ compatible = "isil,isl29023";
+ reg = <0x44>;
+ interrupt-parent = <&lsio_gpio4>;
+ interrupts = <11 2>;
+ };
+
+ mpl3115@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
+
+ max7322: gpio@68 {
+ compatible = "maxim,max7322";
+ reg = <0x68>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ l3g4250@69 {
+ compatible = "st,l3g4200d-gyro";
+ reg = <0x69>;
+ };
+};
+
&i2c1 {
#address-cells = <1>;
#size-cells = <0>;
@@ -283,6 +326,13 @@ IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x0600004c
>;
};
+ pinctrl_i2c0: i2c0grp {
+ fsl,pins = <
+ IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL 0x06000021
+ IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA 0x06000021
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x0600004c
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 05/10] arm64: dts: imx8qm-mek: add i2c0 and children devices
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add i2c0 and all devices under it for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 50 ++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 9f8d3df00f793..e5740f301bde0 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -96,6 +96,49 @@ &adc0 {
status = "okay";
};
+&i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ status = "okay";
+
+ lsm303arg@19 {
+ compatible = "st,lsm303agr-accel";
+ reg = <0x19>;
+ };
+
+ fxas21002c@20 {
+ compatible = "nxp,fxas21002c";
+ reg = <0x20>;
+ };
+
+ isl29023@44 {
+ compatible = "isil,isl29023";
+ reg = <0x44>;
+ interrupt-parent = <&lsio_gpio4>;
+ interrupts = <11 2>;
+ };
+
+ mpl3115@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
+
+ max7322: gpio@68 {
+ compatible = "maxim,max7322";
+ reg = <0x68>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ l3g4250@69 {
+ compatible = "st,l3g4200d-gyro";
+ reg = <0x69>;
+ };
+};
+
&i2c1 {
#address-cells = <1>;
#size-cells = <0>;
@@ -283,6 +326,13 @@ IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31 0x0600004c
>;
};
+ pinctrl_i2c0: i2c0grp {
+ fsl,pins = <
+ IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL 0x06000021
+ IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA 0x06000021
+ >;
+ };
+
pinctrl_i2c1: i2c1grp {
fsl,pins = <
IMX8QM_GPT0_CLK_DMA_I2C1_SCL 0x0600004c
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 06/10] arm64: dts: imx8qm-mek: add cm41_i2c and children devices
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add cm41_i2c and devices under it for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index e5740f301bde0..765ff15b16410 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -222,6 +222,26 @@ &sai7 {
status = "okay";
};
+&cm41_i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cm41_i2c>;
+ status = "okay";
+
+ pca6416: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&cm41_intmux {
+ status = "okay";
+};
+
&lpuart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lpuart0>;
@@ -353,6 +373,13 @@ IMX8QM_ADC_IN0_DMA_ADC0_IN0 0xc0000060
>;
};
+ pinctrl_cm41_i2c: cm41i2cgrp {
+ fsl,pins = <
+ IMX8QM_M41_I2C0_SDA_M41_I2C0_SDA 0x0600004c
+ IMX8QM_M41_I2C0_SCL_M41_I2C0_SCL 0x0600004c
+ >;
+ };
+
pinctrl_fec1: fec1grp {
fsl,pins = <
IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000020
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 06/10] arm64: dts: imx8qm-mek: add cm41_i2c and children devices
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add cm41_i2c and devices under it for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index e5740f301bde0..765ff15b16410 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -222,6 +222,26 @@ &sai7 {
status = "okay";
};
+&cm41_i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cm41_i2c>;
+ status = "okay";
+
+ pca6416: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&cm41_intmux {
+ status = "okay";
+};
+
&lpuart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lpuart0>;
@@ -353,6 +373,13 @@ IMX8QM_ADC_IN0_DMA_ADC0_IN0 0xc0000060
>;
};
+ pinctrl_cm41_i2c: cm41i2cgrp {
+ fsl,pins = <
+ IMX8QM_M41_I2C0_SDA_M41_I2C0_SDA 0x0600004c
+ IMX8QM_M41_I2C0_SCL_M41_I2C0_SCL 0x0600004c
+ >;
+ };
+
pinctrl_fec1: fec1grp {
fsl,pins = <
IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000020
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 07/10] arm64: dts: imx8qm-mek: add flexcan support
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add flexcan[1,2,3] support for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 80 ++++++++++++++++++++++++++++
1 file changed, 80 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 765ff15b16410..068bb77ed08aa 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -40,6 +40,44 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
enable-active-high;
};
+ reg_can01_en: regulator-can01-gen {
+ compatible = "regulator-fixed";
+ regulator-name = "can01-en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_can2_en: regulator-can2-gen {
+ compatible = "regulator-fixed";
+ regulator-name = "can2-en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_can01_stby: regulator-can01-stby {
+ compatible = "regulator-fixed";
+ regulator-name = "can01-stby";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_can01_en>;
+ };
+
+ reg_can2_stby: regulator-can2-stby {
+ compatible = "regulator-fixed";
+ regulator-name = "can2-stby";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_can2_en>;
+ };
+
reg_vref_1v8: regulator-adc-vref {
compatible = "regulator-fixed";
regulator-name = "vref_1v8";
@@ -242,6 +280,27 @@ &cm41_intmux {
status = "okay";
};
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can01_stby>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can01_stby>;
+ status = "okay";
+};
+
+&flexcan3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan3>;
+ xceiver-supply = <®_can2_stby>;
+ status = "okay";
+};
+
&lpuart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lpuart0>;
@@ -434,6 +493,27 @@ IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x06000021
>;
};
+ pinctrl_flexcan1: flexcan0grp {
+ fsl,pins = <
+ IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x21
+ IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX 0x21
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan1grp {
+ fsl,pins = <
+ IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX 0x21
+ IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX 0x21
+ >;
+ };
+
+ pinctrl_flexcan3: flexcan3grp {
+ fsl,pins = <
+ IMX8QM_FLEXCAN2_TX_DMA_FLEXCAN2_TX 0x21
+ IMX8QM_FLEXCAN2_RX_DMA_FLEXCAN2_RX 0x21
+ >;
+ };
+
pinctrl_lpuart0: lpuart0grp {
fsl,pins = <
IMX8QM_UART0_RX_DMA_UART0_RX 0x06000020
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 07/10] arm64: dts: imx8qm-mek: add flexcan support
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add flexcan[1,2,3] support for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 80 ++++++++++++++++++++++++++++
1 file changed, 80 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 765ff15b16410..068bb77ed08aa 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -40,6 +40,44 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
enable-active-high;
};
+ reg_can01_en: regulator-can01-gen {
+ compatible = "regulator-fixed";
+ regulator-name = "can01-en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_can2_en: regulator-can2-gen {
+ compatible = "regulator-fixed";
+ regulator-name = "can2-en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_can01_stby: regulator-can01-stby {
+ compatible = "regulator-fixed";
+ regulator-name = "can01-stby";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_can01_en>;
+ };
+
+ reg_can2_stby: regulator-can2-stby {
+ compatible = "regulator-fixed";
+ regulator-name = "can2-stby";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pca6416 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <®_can2_en>;
+ };
+
reg_vref_1v8: regulator-adc-vref {
compatible = "regulator-fixed";
regulator-name = "vref_1v8";
@@ -242,6 +280,27 @@ &cm41_intmux {
status = "okay";
};
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_can01_stby>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_can01_stby>;
+ status = "okay";
+};
+
+&flexcan3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan3>;
+ xceiver-supply = <®_can2_stby>;
+ status = "okay";
+};
+
&lpuart0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lpuart0>;
@@ -434,6 +493,27 @@ IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x06000021
>;
};
+ pinctrl_flexcan1: flexcan0grp {
+ fsl,pins = <
+ IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x21
+ IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX 0x21
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan1grp {
+ fsl,pins = <
+ IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX 0x21
+ IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX 0x21
+ >;
+ };
+
+ pinctrl_flexcan3: flexcan3grp {
+ fsl,pins = <
+ IMX8QM_FLEXCAN2_TX_DMA_FLEXCAN2_TX 0x21
+ IMX8QM_FLEXCAN2_RX_DMA_FLEXCAN2_RX 0x21
+ >;
+ };
+
pinctrl_lpuart0: lpuart0grp {
fsl,pins = <
IMX8QM_UART0_RX_DMA_UART0_RX 0x06000020
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 08/10] arm64: dts: imx8qm-mek: add lsio mu5 and mu6
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add lsio mu5 and mu6.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 068bb77ed08aa..c8b24c46c30a4 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -260,6 +260,14 @@ &sai7 {
status = "okay";
};
+&lsio_mu5 {
+ status = "okay";
+};
+
+&lsio_mu6 {
+ status = "okay";
+};
+
&cm41_i2c {
#address-cells = <1>;
#size-cells = <0>;
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 08/10] arm64: dts: imx8qm-mek: add lsio mu5 and mu6
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add lsio mu5 and mu6.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 068bb77ed08aa..c8b24c46c30a4 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -260,6 +260,14 @@ &sai7 {
status = "okay";
};
+&lsio_mu5 {
+ status = "okay";
+};
+
+&lsio_mu6 {
+ status = "okay";
+};
+
&cm41_i2c {
#address-cells = <1>;
#size-cells = <0>;
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 09/10] arm64: dts: imx8qm: add ocopt and fec_mac[0,1]
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
add ocotp ad fec_mac[0,1] for imx8qm.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index 96a940c6046d8..734bee4294dfe 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -333,6 +333,21 @@ rtc: rtc {
compatible = "fsl,imx8qxp-sc-rtc";
};
+ ocotp: ocotp {
+ compatible = "fsl,imx8qm-scu-ocotp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ read-only;
+
+ fec_mac0: mac@1c4 {
+ reg = <0x1c4 6>;
+ };
+
+ fec_mac1: mac@1c6 {
+ reg = <0x1c6 6>;
+ };
+ };
+
tsens: thermal-sensor {
compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal";
#thermal-sensor-cells = <1>;
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 09/10] arm64: dts: imx8qm: add ocopt and fec_mac[0,1]
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
add ocotp ad fec_mac[0,1] for imx8qm.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index 96a940c6046d8..734bee4294dfe 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -333,6 +333,21 @@ rtc: rtc {
compatible = "fsl,imx8qxp-sc-rtc";
};
+ ocotp: ocotp {
+ compatible = "fsl,imx8qm-scu-ocotp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ read-only;
+
+ fec_mac0: mac@1c4 {
+ reg = <0x1c4 6>;
+ };
+
+ fec_mac1: mac@1c6 {
+ reg = <0x1c6 6>;
+ };
+ };
+
tsens: thermal-sensor {
compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal";
#thermal-sensor-cells = <1>;
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 10/10] arm64: dts: imx8qm-mek: add fec2 support
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 16:36 ` Frank Li
-1 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add fec2 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 40 ++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index c8b24c46c30a4..09f2d3e76a3fe 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -40,6 +40,15 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
enable-active-high;
};
+ reg_fec2_supply: fec2_nvcc {
+ compatible = "regulator-fixed";
+ regulator-name = "fec2_nvcc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&max7322 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
reg_can01_en: regulator-can01-gen {
compatible = "regulator-fixed";
regulator-name = "can01-en";
@@ -382,6 +391,19 @@ ethphy1: ethernet-phy@1 {
};
};
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec2>;
+ phy-mode = "rgmii-txid";
+ phy-handle = <ðphy1>;
+ phy-supply = <®_fec2_supply>;
+ nvmem-cells = <&fec_mac1>;
+ nvmem-cell-names = "mac-address";
+ rx-internal-delay-ps = <2000>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
@@ -501,6 +523,24 @@ IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x06000021
>;
};
+ pinctrl_fec2: fec2grp {
+ fsl,pins = <
+ IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0
+ IMX8QM_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000060
+ IMX8QM_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000060
+ IMX8QM_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000060
+ IMX8QM_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000060
+ IMX8QM_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000060
+ IMX8QM_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000060
+ IMX8QM_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000060
+ IMX8QM_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000060
+ IMX8QM_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000060
+ IMX8QM_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000060
+ IMX8QM_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000060
+ IMX8QM_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000060
+ >;
+ };
+
pinctrl_flexcan1: flexcan0grp {
fsl,pins = <
IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x21
--
2.34.1
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v2 10/10] arm64: dts: imx8qm-mek: add fec2 support
@ 2024-04-18 16:36 ` Frank Li
0 siblings, 0 replies; 24+ messages in thread
From: Frank Li @ 2024-04-18 16:36 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, imx, linux-arm-kernel, linux-kernel, Frank Li
Add fec2 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 40 ++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index c8b24c46c30a4..09f2d3e76a3fe 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -40,6 +40,15 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
enable-active-high;
};
+ reg_fec2_supply: fec2_nvcc {
+ compatible = "regulator-fixed";
+ regulator-name = "fec2_nvcc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&max7322 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
reg_can01_en: regulator-can01-gen {
compatible = "regulator-fixed";
regulator-name = "can01-en";
@@ -382,6 +391,19 @@ ethphy1: ethernet-phy@1 {
};
};
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec2>;
+ phy-mode = "rgmii-txid";
+ phy-handle = <ðphy1>;
+ phy-supply = <®_fec2_supply>;
+ nvmem-cells = <&fec_mac1>;
+ nvmem-cell-names = "mac-address";
+ rx-internal-delay-ps = <2000>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
@@ -501,6 +523,24 @@ IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x06000021
>;
};
+ pinctrl_fec2: fec2grp {
+ fsl,pins = <
+ IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0
+ IMX8QM_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000060
+ IMX8QM_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000060
+ IMX8QM_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000060
+ IMX8QM_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000060
+ IMX8QM_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000060
+ IMX8QM_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000060
+ IMX8QM_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000060
+ IMX8QM_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000060
+ IMX8QM_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000060
+ IMX8QM_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000060
+ IMX8QM_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000060
+ IMX8QM_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000060
+ >;
+ };
+
pinctrl_flexcan1: flexcan0grp {
fsl,pins = <
IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x21
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH v2 05/10] arm64: dts: imx8qm-mek: add i2c0 and children devices
2024-04-18 16:36 ` Frank Li
@ 2024-04-18 23:03 ` Fabio Estevam
-1 siblings, 0 replies; 24+ messages in thread
From: Fabio Estevam @ 2024-04-18 23:03 UTC (permalink / raw)
To: Frank Li
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, devicetree, imx,
linux-arm-kernel, linux-kernel
On Thu, Apr 18, 2024 at 1:37 PM Frank Li <Frank.Li@nxp.com> wrote:
> + lsm303arg@19 {
> + compatible = "st,lsm303agr-accel";
> + reg = <0x19>;
> + };
> +
> + fxas21002c@20 {
> + compatible = "nxp,fxas21002c";
> + reg = <0x20>;
> + };
> +
> + isl29023@44 {
> + compatible = "isil,isl29023";
> + reg = <0x44>;
> + interrupt-parent = <&lsio_gpio4>;
> + interrupts = <11 2>;
> + };
> +
> + mpl3115@60 {
> + compatible = "fsl,mpl3115";
> + reg = <0x60>;
> + };
> +
> + max7322: gpio@68 {
> + compatible = "maxim,max7322";
> + reg = <0x68>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + l3g4250@69 {
> + compatible = "st,l3g4200d-gyro";
> + reg = <0x69>;
> + };
Same comment I did yesterday on another patch from you: none of these
node names are generic.
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH v2 05/10] arm64: dts: imx8qm-mek: add i2c0 and children devices
@ 2024-04-18 23:03 ` Fabio Estevam
0 siblings, 0 replies; 24+ messages in thread
From: Fabio Estevam @ 2024-04-18 23:03 UTC (permalink / raw)
To: Frank Li
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, devicetree, imx,
linux-arm-kernel, linux-kernel
On Thu, Apr 18, 2024 at 1:37 PM Frank Li <Frank.Li@nxp.com> wrote:
> + lsm303arg@19 {
> + compatible = "st,lsm303agr-accel";
> + reg = <0x19>;
> + };
> +
> + fxas21002c@20 {
> + compatible = "nxp,fxas21002c";
> + reg = <0x20>;
> + };
> +
> + isl29023@44 {
> + compatible = "isil,isl29023";
> + reg = <0x44>;
> + interrupt-parent = <&lsio_gpio4>;
> + interrupts = <11 2>;
> + };
> +
> + mpl3115@60 {
> + compatible = "fsl,mpl3115";
> + reg = <0x60>;
> + };
> +
> + max7322: gpio@68 {
> + compatible = "maxim,max7322";
> + reg = <0x68>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + l3g4250@69 {
> + compatible = "st,l3g4200d-gyro";
> + reg = <0x69>;
> + };
Same comment I did yesterday on another patch from you: none of these
node names are generic.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2024-04-18 23:04 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-04-18 16:36 [PATCH v2 00/10] arm64: dts: imx8qm Add audio\flexcan\i2c\fec1 nodes for imx8qm-mek board Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 01/10] arm64: dts: imx8-ss-audio: remove memory-region = <&dsp_reserved>; Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 02/10] arm64: dts: imx8qm-ss-audio: add audio nodes Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 03/10] arm64: dts: imx8qm-mek: add sai and wm8960 support Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 04/10] arm64: dts: imx8x: add cm41 subsystem dtsi Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 05/10] arm64: dts: imx8qm-mek: add i2c0 and children devices Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 23:03 ` Fabio Estevam
2024-04-18 23:03 ` Fabio Estevam
2024-04-18 16:36 ` [PATCH v2 06/10] arm64: dts: imx8qm-mek: add cm41_i2c " Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 07/10] arm64: dts: imx8qm-mek: add flexcan support Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 08/10] arm64: dts: imx8qm-mek: add lsio mu5 and mu6 Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 09/10] arm64: dts: imx8qm: add ocopt and fec_mac[0,1] Frank Li
2024-04-18 16:36 ` Frank Li
2024-04-18 16:36 ` [PATCH v2 10/10] arm64: dts: imx8qm-mek: add fec2 support Frank Li
2024-04-18 16:36 ` Frank Li
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.