* [PATCH v2 0/3] Arranging pin mux in alphabetical order
@ 2024-04-18 7:16 ` Udit Kumar
0 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
This series aims to align ordering of pin muxes in following order
main_pmx0/1, wkup_pmx0/1/2/3.
Sorry for this cosmetic push, but usages of pin muxes was not consistent
across the platforms, and even for j784s4-evm wkup_pmx1 was coded at two
place.
Dependency
This series is dependent upon
https://lore.kernel.org/all/20240415095605.3547933-1-u-kumar1@ti.com/
Boot logs
https://gist.github.com/uditkumarti/28d7746486466f6d35f833ac829bbf6d
Change logs:
Changes in v2:
Splitting patch series into two as refactoring and fixes,
This series is for refactoring
Link of v1: https://lore.kernel.org/all/20240415063329.3286600-1-u-kumar1@ti.com/
Udit Kumar (3):
arm64: dts: ti: k3-j784s4-evm: Arranging pin mux in alphabetical order
arm64: dts: ti: k3-j721s2: Arranging pin mux in alphabetical order
arm64: dts: ti: k3-j7200: Arranging pin mux in alphabetical order
.../dts/ti/k3-j7200-common-proc-board.dts | 131 +++++++++---------
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 31 +++--
.../dts/ti/k3-j721s2-common-proc-board.dts | 29 ++--
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 31 +++--
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 108 +++++++--------
5 files changed, 163 insertions(+), 167 deletions(-)
--
2.34.1
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 0/3] Arranging pin mux in alphabetical order
@ 2024-04-18 7:16 ` Udit Kumar
0 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
This series aims to align ordering of pin muxes in following order
main_pmx0/1, wkup_pmx0/1/2/3.
Sorry for this cosmetic push, but usages of pin muxes was not consistent
across the platforms, and even for j784s4-evm wkup_pmx1 was coded at two
place.
Dependency
This series is dependent upon
https://lore.kernel.org/all/20240415095605.3547933-1-u-kumar1@ti.com/
Boot logs
https://gist.github.com/uditkumarti/28d7746486466f6d35f833ac829bbf6d
Change logs:
Changes in v2:
Splitting patch series into two as refactoring and fixes,
This series is for refactoring
Link of v1: https://lore.kernel.org/all/20240415063329.3286600-1-u-kumar1@ti.com/
Udit Kumar (3):
arm64: dts: ti: k3-j784s4-evm: Arranging pin mux in alphabetical order
arm64: dts: ti: k3-j721s2: Arranging pin mux in alphabetical order
arm64: dts: ti: k3-j7200: Arranging pin mux in alphabetical order
.../dts/ti/k3-j7200-common-proc-board.dts | 131 +++++++++---------
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 31 +++--
.../dts/ti/k3-j721s2-common-proc-board.dts | 29 ++--
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 31 +++--
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 108 +++++++--------
5 files changed, 163 insertions(+), 167 deletions(-)
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 1/3] arm64: dts: ti: k3-j784s4-evm: Arranging pin mux in alphabetical order
2024-04-18 7:16 ` Udit Kumar
@ 2024-04-18 7:16 ` Udit Kumar
-1 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 108 +++++++++++------------
1 file changed, 52 insertions(+), 56 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index d511b25d62e3..97b0bffc38c5 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -338,6 +338,58 @@ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
};
};
+&wkup_pmx0 {
+ bootph-all;
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+ J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+ J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+ J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+ J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+ >;
+ };
+};
+
+&wkup_pmx1 {
+ bootph-all;
+ mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
+ >;
+ };
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
+ J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
+ J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
+ J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
+ >;
+ };
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx2 {
bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
@@ -417,62 +469,6 @@ J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
};
-&wkup_pmx1 {
- status = "okay";
-
- pmic_irq_pins_default: pmic-irq-default-pins {
- pinctrl-single,pins = <
- /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
- J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
- >;
- };
-};
-
-&wkup_pmx0 {
- bootph-all;
- mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
- J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
- J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
- J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
- J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
- J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
- J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
- J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
- J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
- J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
- J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
- >;
- };
-};
-
-&wkup_pmx1 {
- bootph-all;
- mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
- J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
- >;
- };
-
- mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
- J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
- J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
- J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
- J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
- J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
- J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
- J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
- >;
- };
-};
-
&wkup_uart0 {
/* Firmware usage */
status = "reserved";
--
2.34.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 1/3] arm64: dts: ti: k3-j784s4-evm: Arranging pin mux in alphabetical order
@ 2024-04-18 7:16 ` Udit Kumar
0 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 108 +++++++++++------------
1 file changed, 52 insertions(+), 56 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index d511b25d62e3..97b0bffc38c5 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -338,6 +338,58 @@ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
};
};
+&wkup_pmx0 {
+ bootph-all;
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+ J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+ J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+ J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+ J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+ >;
+ };
+};
+
+&wkup_pmx1 {
+ bootph-all;
+ mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
+ J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
+ >;
+ };
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+ bootph-all;
+ pinctrl-single,pins = <
+ J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
+ J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
+ J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
+ J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
+ J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
+ J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
+ J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
+ J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
+ >;
+ };
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx2 {
bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
@@ -417,62 +469,6 @@ J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
};
-&wkup_pmx1 {
- status = "okay";
-
- pmic_irq_pins_default: pmic-irq-default-pins {
- pinctrl-single,pins = <
- /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
- J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
- >;
- };
-};
-
-&wkup_pmx0 {
- bootph-all;
- mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
- J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
- J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
- J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
- J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
- J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
- J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
- J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
- J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
- J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
- J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
- >;
- };
-};
-
-&wkup_pmx1 {
- bootph-all;
- mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
- J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
- >;
- };
-
- mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
- bootph-all;
- pinctrl-single,pins = <
- J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
- J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
- J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
- J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
- J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
- J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
- J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
- J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
- >;
- };
-};
-
&wkup_uart0 {
/* Firmware usage */
status = "reserved";
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/3] arm64: dts: ti: k3-j721s2: Arranging pin mux in alphabetical order
2024-04-18 7:16 ` Udit Kumar
@ 2024-04-18 7:16 ` Udit Kumar
-1 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j721s2-common-proc-board.dts | 29 ++++++++---------
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 31 ++++++++++---------
2 files changed, 31 insertions(+), 29 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c5a0b7cbb14f..fed89e34e35e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -194,6 +194,21 @@ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */
};
};
+&wkup_pmx1 {
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+ J721S2_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+ J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+ J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+ J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+ J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_uart0_pins_default: wkup-uart0-default-pins {
pinctrl-single,pins = <
@@ -289,20 +304,6 @@ J721S2_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
};
};
-&wkup_pmx1 {
- mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
- pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
- J721S2_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
- J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
- J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
- J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
- J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
- J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
- J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
- >;
- };
-};
&main_gpio0 {
status = "okay";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 623c8421525d..8adf2dfbf3a3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -153,6 +153,22 @@ transceiver0: can-phy0 {
};
};
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-default-pins {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
+ J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
+ >;
+ };
+
+ main_mcan16_pins_default: main-mcan16-default-pins {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
+ J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
+ >;
+ };
+};
+
&wkup_pmx0 {
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
@@ -190,21 +206,6 @@ J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (H27) WKUP_I2C0_SDA */
};
};
-&main_pmx0 {
- main_i2c0_pins_default: main-i2c0-default-pins {
- pinctrl-single,pins = <
- J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
- J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
- >;
- };
-
- main_mcan16_pins_default: main-mcan16-default-pins {
- pinctrl-single,pins = <
- J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
- J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
- >;
- };
-};
&wkup_i2c0 {
status = "okay";
--
2.34.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 2/3] arm64: dts: ti: k3-j721s2: Arranging pin mux in alphabetical order
@ 2024-04-18 7:16 ` Udit Kumar
0 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j721s2-common-proc-board.dts | 29 ++++++++---------
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 31 ++++++++++---------
2 files changed, 31 insertions(+), 29 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c5a0b7cbb14f..fed89e34e35e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -194,6 +194,21 @@ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */
};
};
+&wkup_pmx1 {
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+ J721S2_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+ J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+ J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+ J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+ J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_uart0_pins_default: wkup-uart0-default-pins {
pinctrl-single,pins = <
@@ -289,20 +304,6 @@ J721S2_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (N27) MCU_ADC1_AIN7 */
};
};
-&wkup_pmx1 {
- mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
- pinctrl-single,pins = <
- J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
- J721S2_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
- J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
- J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
- J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
- J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
- J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
- J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
- >;
- };
-};
&main_gpio0 {
status = "okay";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 623c8421525d..8adf2dfbf3a3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -153,6 +153,22 @@ transceiver0: can-phy0 {
};
};
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-default-pins {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
+ J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
+ >;
+ };
+
+ main_mcan16_pins_default: main-mcan16-default-pins {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
+ J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
+ >;
+ };
+};
+
&wkup_pmx0 {
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
@@ -190,21 +206,6 @@ J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (H27) WKUP_I2C0_SDA */
};
};
-&main_pmx0 {
- main_i2c0_pins_default: main-i2c0-default-pins {
- pinctrl-single,pins = <
- J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
- J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
- >;
- };
-
- main_mcan16_pins_default: main-mcan16-default-pins {
- pinctrl-single,pins = <
- J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
- J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
- >;
- };
-};
&wkup_i2c0 {
status = "okay";
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/3] arm64: dts: ti: k3-j7200: Arranging pin mux in alphabetical order
2024-04-18 7:16 ` Udit Kumar
@ 2024-04-18 7:16 ` Udit Kumar
-1 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 131 +++++++++---------
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 31 +++--
2 files changed, 80 insertions(+), 82 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 6593c5da82c0..e910ac9093e5 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -118,7 +118,70 @@ transceiver3: can-phy3 {
};
};
-&wkup_pmx0 {
+&main_pmx0 {
+ main_uart0_pins_default: main-uart0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
+ J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
+ J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
+ J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
+ >;
+ };
+
+ main_uart1_pins_default: main-uart1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb8, PIN_INPUT, 0) /* (T18) UART1_RXD */
+ J721E_IOPAD(0xbc, PIN_INPUT, 0) /* (T20) UART1_TXD */
+ >;
+ };
+
+ main_uart3_pins_default: main-uart3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x60, PIN_INPUT, 11) /* (T15) MCAN8_TX.UART3_CTSn */
+ J721E_IOPAD(0x30, PIN_INPUT, 11) /* (Y18) MCAN2_TX.UART3_RXD */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
+ J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
+ J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
+ J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
+ J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
+ J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
+ J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
+ J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
+
+ main_mcan3_pins_default: main-mcan3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x3c, PIN_INPUT, 0) /* (W16) MCAN3_RX */
+ J721E_IOPAD(0x38, PIN_OUTPUT, 0) /* (Y21) MCAN3_TX */
+ >;
+ };
+};
+
+&main_pmx1 {
+ main_usbss0_pins_default: main-usbss0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
+ >;
+ };
};
&wkup_pmx2 {
@@ -196,72 +259,6 @@ J721E_WKUP_IOPAD(0x60, PIN_INPUT, 7) /* (D14) WKUP_GPIO0_2 */
};
};
-&main_pmx0 {
- main_uart0_pins_default: main-uart0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
- J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
- J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
- J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
- >;
- };
-
- main_uart1_pins_default: main-uart1-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xb8, PIN_INPUT, 0) /* (T18) UART1_RXD */
- J721E_IOPAD(0xbc, PIN_INPUT, 0) /* (T20) UART1_TXD */
- >;
- };
-
- main_uart3_pins_default: main-uart3-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x60, PIN_INPUT, 11) /* (T15) MCAN8_TX.UART3_CTSn */
- J721E_IOPAD(0x30, PIN_INPUT, 11) /* (Y18) MCAN2_TX.UART3_RXD */
- >;
- };
-
- main_i2c1_pins_default: main-i2c1-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
- J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
- >;
- };
-
- main_mmc1_pins_default: main-mmc1-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
- J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
- J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
- J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
- J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
- J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
- J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
- J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
- >;
- };
-
- vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
- >;
- };
-
- main_mcan3_pins_default: main-mcan3-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x3c, PIN_INPUT, 0) /* (W16) MCAN3_RX */
- J721E_IOPAD(0x38, PIN_OUTPUT, 0) /* (Y21) MCAN3_TX */
- >;
- };
-};
-
-&main_pmx1 {
- main_usbss0_pins_default: main-usbss0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
- >;
- };
-};
-
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
status = "reserved";
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 7e6a584ac6f0..d9eddc5191b1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -103,6 +103,22 @@ transceiver0: can-phy0 {
};
};
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
+ main_mcan0_pins_default: main-mcan0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
+ J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
+ >;
+ };
+};
+
&wkup_pmx0 {
mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
pinctrl-single,pins = <
@@ -156,21 +172,6 @@ J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
};
};
-&main_pmx0 {
- main_i2c0_pins_default: main-i2c0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
- J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
- >;
- };
-
- main_mcan0_pins_default: main-mcan0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
- J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
- >;
- };
-};
&hbmc {
/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
--
2.34.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v2 3/3] arm64: dts: ti: k3-j7200: Arranging pin mux in alphabetical order
@ 2024-04-18 7:16 ` Udit Kumar
0 siblings, 0 replies; 8+ messages in thread
From: Udit Kumar @ 2024-04-18 7:16 UTC (permalink / raw)
To: nm, vigneshr, linux-arm-kernel, devicetree, francesco
Cc: kristo, robh, krzk+dt, conor+dt, linux-kernel, Udit Kumar
Arranging pin mux in order of main_pmx0/1, wkup_pmx0/1/2/3.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 131 +++++++++---------
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 31 +++--
2 files changed, 80 insertions(+), 82 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 6593c5da82c0..e910ac9093e5 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -118,7 +118,70 @@ transceiver3: can-phy3 {
};
};
-&wkup_pmx0 {
+&main_pmx0 {
+ main_uart0_pins_default: main-uart0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
+ J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
+ J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
+ J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
+ >;
+ };
+
+ main_uart1_pins_default: main-uart1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb8, PIN_INPUT, 0) /* (T18) UART1_RXD */
+ J721E_IOPAD(0xbc, PIN_INPUT, 0) /* (T20) UART1_TXD */
+ >;
+ };
+
+ main_uart3_pins_default: main-uart3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x60, PIN_INPUT, 11) /* (T15) MCAN8_TX.UART3_CTSn */
+ J721E_IOPAD(0x30, PIN_INPUT, 11) /* (Y18) MCAN2_TX.UART3_RXD */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
+ J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
+ J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
+ J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
+ J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
+ J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
+ J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
+ J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
+
+ main_mcan3_pins_default: main-mcan3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x3c, PIN_INPUT, 0) /* (W16) MCAN3_RX */
+ J721E_IOPAD(0x38, PIN_OUTPUT, 0) /* (Y21) MCAN3_TX */
+ >;
+ };
+};
+
+&main_pmx1 {
+ main_usbss0_pins_default: main-usbss0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
+ >;
+ };
};
&wkup_pmx2 {
@@ -196,72 +259,6 @@ J721E_WKUP_IOPAD(0x60, PIN_INPUT, 7) /* (D14) WKUP_GPIO0_2 */
};
};
-&main_pmx0 {
- main_uart0_pins_default: main-uart0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
- J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
- J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
- J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
- >;
- };
-
- main_uart1_pins_default: main-uart1-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xb8, PIN_INPUT, 0) /* (T18) UART1_RXD */
- J721E_IOPAD(0xbc, PIN_INPUT, 0) /* (T20) UART1_TXD */
- >;
- };
-
- main_uart3_pins_default: main-uart3-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x60, PIN_INPUT, 11) /* (T15) MCAN8_TX.UART3_CTSn */
- J721E_IOPAD(0x30, PIN_INPUT, 11) /* (Y18) MCAN2_TX.UART3_RXD */
- >;
- };
-
- main_i2c1_pins_default: main-i2c1-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
- J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
- >;
- };
-
- main_mmc1_pins_default: main-mmc1-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
- J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
- J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
- J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
- J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
- J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
- J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
- J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
- >;
- };
-
- vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
- >;
- };
-
- main_mcan3_pins_default: main-mcan3-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x3c, PIN_INPUT, 0) /* (W16) MCAN3_RX */
- J721E_IOPAD(0x38, PIN_OUTPUT, 0) /* (Y21) MCAN3_TX */
- >;
- };
-};
-
-&main_pmx1 {
- main_usbss0_pins_default: main-usbss0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
- >;
- };
-};
-
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
status = "reserved";
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 7e6a584ac6f0..d9eddc5191b1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -103,6 +103,22 @@ transceiver0: can-phy0 {
};
};
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
+ main_mcan0_pins_default: main-mcan0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
+ J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
+ >;
+ };
+};
+
&wkup_pmx0 {
mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
pinctrl-single,pins = <
@@ -156,21 +172,6 @@ J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
};
};
-&main_pmx0 {
- main_i2c0_pins_default: main-i2c0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
- J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
- >;
- };
-
- main_mcan0_pins_default: main-mcan0-default-pins {
- pinctrl-single,pins = <
- J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
- J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
- >;
- };
-};
&hbmc {
/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 8+ messages in thread
end of thread, other threads:[~2024-04-18 7:17 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-04-18 7:16 [PATCH v2 0/3] Arranging pin mux in alphabetical order Udit Kumar
2024-04-18 7:16 ` Udit Kumar
2024-04-18 7:16 ` [PATCH v2 1/3] arm64: dts: ti: k3-j784s4-evm: " Udit Kumar
2024-04-18 7:16 ` Udit Kumar
2024-04-18 7:16 ` [PATCH v2 2/3] arm64: dts: ti: k3-j721s2: " Udit Kumar
2024-04-18 7:16 ` Udit Kumar
2024-04-18 7:16 ` [PATCH v2 3/3] arm64: dts: ti: k3-j7200: " Udit Kumar
2024-04-18 7:16 ` Udit Kumar
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.