From: Tengfei Fan <quic_tengfan@quicinc.com>
To: <andersson@kernel.org>, <konrad.dybcio@linaro.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<dmitry.baryshkov@linaro.org>
Cc: <keescook@chromium.org>, <tony.luck@intel.com>,
<gpiccoli@igalia.com>, <linux-arm-msm@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-hardening@vger.kernel.org>, <kernel@quicinc.com>,
Tengfei Fan <quic_tengfan@quicinc.com>,
Qiang Yu <quic_qianyu@quicinc.com>,
Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Subject: [PATCH v7 4/4] arm64: dts: qcom: aim300: add AIM300 AIoT
Date: Wed, 24 Apr 2024 10:45:08 +0800 [thread overview]
Message-ID: <20240424024508.3857602-5-quic_tengfan@quicinc.com> (raw)
In-Reply-To: <20240424024508.3857602-1-quic_tengfan@quicinc.com>
Add AIM300 AIoT Carrier board DTS support, including usb, UART, PCIe,
I2C functions support.
Here is a diagram of AIM300 AIoT Carrie Board and SoM
+--------------------------------------------------+
| AIM300 AIOT Carrier Board |
| |
| +-----------------+ |
|power----->| Fixed regulator |---------+ |
| +-----------------+ | |
| | |
| v VPH_PWR |
| +----------------------------------------------+ |
| | AIM300 SOM | | |
| | |VPH_PWR | |
| | v | |
| | +-------+ +--------+ +------+ | |
| | | UFS | | QCS8550| |PMIC | | |
| | +-------+ +--------+ +------+ | |
| | | |
| +----------------------------------------------+ |
| |
| +----+ +------+ |
| |USB | | UART | |
| +----+ +------+ |
+--------------------------------------------------+
Co-developed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Co-developed-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Signed-off-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/qcs8550-aim300-aiot.dts | 343 ++++++++++++++++++
2 files changed, 344 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f63abb43e9fe..c46c10d85697 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -96,6 +96,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb2210-rb1.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb4210-rb2.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts b/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts
new file mode 100644
index 000000000000..146bf6ea9e6a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023-2024, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "qcs8550-aim300.dtsi"
+#include "pm8010.dtsi"
+#include "pmr735d_a.dtsi"
+#include "pmr735d_b.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QCS8550 AIM300 AIOT";
+ compatible = "qcom,qcs8550-aim300-aiot", "qcom,qcs8550-aim300", "qcom,qcs8550",
+ "qcom,sm8550";
+
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ debounce-interval = <15>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&redriver_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&fsa4480_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ };
+
+ regulators-3 {
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ };
+
+ regulators-4 {
+ vdd-s4-supply = <&vph_pwr>;
+ };
+
+ regulators-5 {
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ };
+};
+
+&i2c_hub_2 {
+ status = "okay";
+
+ typec-mux@42 {
+ compatible = "fcs,fsa4480";
+ reg = <0x42>;
+
+ vcc-supply = <&vreg_bob1>;
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ fsa4480_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+
+ typec-retimer@1c {
+ compatible = "onnn,nb7vpq904m";
+ reg = <0x1c>;
+
+ vcc-supply = <&vreg_l15b_1p8>;
+
+ orientation-switch;
+ retimer-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ redriver_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ redriver_ss_in: endpoint {
+ data-lanes = <3 2 1 0>;
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dsi0 {
+ status = "okay";
+
+ panel@0 {
+ compatible = "visionox,vtdr6130";
+ reg = <0>;
+
+ pinctrl-0 = <&dsi_active>, <&te_active>;
+ pinctrl-1 = <&dsi_suspend>, <&te_suspend>;
+ pinctrl-names = "default", "sleep";
+
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+ vci-supply = <&vreg_l13b_3p0>;
+ vdd-supply = <&vreg_l11b_1p2>;
+ vddio-supply = <&vreg_l12b_1p8>;
+
+ port {
+ panel0_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+ };
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&panel0_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ status = "okay";
+};
+
+&pcie1 {
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ status = "okay";
+};
+
+&pm8550_gpios {
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs8550/adsp.mbn",
+ "qcom/qcs8550/adsp_dtbs.elf";
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs8550/cdsp.mbn",
+ "qcom/qcs8550/cdsp_dtbs.elf";
+ status = "okay";
+};
+
+&swr1 {
+ status = "okay";
+};
+
+&swr2 {
+ status = "okay";
+};
+
+&tlmm {
+ gpio-reserved-ranges = <32 8>;
+
+ dsi_active: dsi-active-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ dsi_suspend: dsi-suspend-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ te_active: te-active-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ te_suspend: te-suspend-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+};
+
+&uart7 {
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+};
+
+&usb_1_hsphy {
+ status = "okay";
+};
+
+&usb_dp_qmpphy {
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&redriver_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+};
--
2.25.1
next prev parent reply other threads:[~2024-04-24 2:46 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-04-24 2:45 [PATCH v7 0/4] arm64: qcom: add AIM300 AIoT board support Tengfei Fan
2024-04-24 2:45 ` [PATCH v7 1/4] dt-bindings: arm: qcom: Document QCS8550 SoC and the AIM300 AIoT board Tengfei Fan
2024-04-24 2:45 ` [PATCH v7 2/4] arm64: dts: qcom: qcs8550: introduce qcs8550 dtsi Tengfei Fan
2024-04-24 2:45 ` [PATCH v7 3/4] arm64: dts: qcom: add base AIM300 dtsi Tengfei Fan
2024-04-24 23:47 ` Dmitry Baryshkov
2024-04-25 3:21 ` Tengfei Fan
2024-04-24 2:45 ` Tengfei Fan [this message]
2024-04-24 23:50 ` [PATCH v7 4/4] arm64: dts: qcom: aim300: add AIM300 AIoT Dmitry Baryshkov
2024-04-25 3:23 ` Tengfei Fan
2024-04-24 13:14 ` [PATCH v7 0/4] arm64: qcom: add AIM300 AIoT board support Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240424024508.3857602-5-quic_tengfan@quicinc.com \
--to=quic_tengfan@quicinc.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=gpiccoli@igalia.com \
--cc=keescook@chromium.org \
--cc=kernel@quicinc.com \
--cc=konrad.dybcio@linaro.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-hardening@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=quic_qianyu@quicinc.com \
--cc=quic_ziyuzhan@quicinc.com \
--cc=robh@kernel.org \
--cc=tony.luck@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.