* [PATCH v3 0/3] arm64: dts: add i.MX95 and EVK board
@ 2024-04-28 12:22 ` Peng Fan (OSS)
0 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan, Conor Dooley
Add a minimal i.MX95 dtsi and EVK board dts.
i.MX95 has a M33 running SCMI firmware, but as of now, the scmi pinctrl
driver still not ready for i.MX95, so we count on bootloader to
configure the pinctrl for lpuart and sdhc and it boots well. After pinctrl
driver ready, we could move to use scmi pinctrl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Changes in v3:
- Drop irqsteer node because binding not accepted
- Pass dtbs_check
- Link to v2: https://lore.kernel.org/r/20240226-imx95-dts-v2-0-00e36637b07e@nxp.com
Changes in v2:
- Addressed Rob and Krzysztof's comments, and fix dts_check issue
To pass the dtbs_check, need apply:
https://lore.kernel.org/all/20240226070910.3379108-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240226130243.3820915-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240226130516.3821803-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240226130826.3824251-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240219-imx-mailbox-v8-1-75535a87794e@nxp.com/
- Link to v1: https://lore.kernel.org/r/20240218-imx95-dts-v1-0-2959f89f2018@nxp.com
---
Peng Fan (3):
dt-bindings: arm: fsl: add i.MX95 19x19 EVK board
arm64: dts: freescale: add i.MX95 basic dtsi
arm64: dts: freescale: add i.MX95 19x19 EVK minimal board dts
Documentation/devicetree/bindings/arm/fsl.yaml | 6 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 111 ++
arch/arm64/boot/dts/freescale/imx95-clock.h | 187 ++++
arch/arm64/boot/dts/freescale/imx95-power.h | 55 +
arch/arm64/boot/dts/freescale/imx95.dtsi | 1152 +++++++++++++++++++++
6 files changed, 1512 insertions(+)
---
base-commit: bb7a2467e6beef44a80a17d45ebf2931e7631083
change-id: 20240428-imx95-dts-v3-bee59f0e559b
Best regards,
--
Peng Fan <peng.fan@nxp.com>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v3 0/3] arm64: dts: add i.MX95 and EVK board
@ 2024-04-28 12:22 ` Peng Fan (OSS)
0 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan, Conor Dooley
Add a minimal i.MX95 dtsi and EVK board dts.
i.MX95 has a M33 running SCMI firmware, but as of now, the scmi pinctrl
driver still not ready for i.MX95, so we count on bootloader to
configure the pinctrl for lpuart and sdhc and it boots well. After pinctrl
driver ready, we could move to use scmi pinctrl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Changes in v3:
- Drop irqsteer node because binding not accepted
- Pass dtbs_check
- Link to v2: https://lore.kernel.org/r/20240226-imx95-dts-v2-0-00e36637b07e@nxp.com
Changes in v2:
- Addressed Rob and Krzysztof's comments, and fix dts_check issue
To pass the dtbs_check, need apply:
https://lore.kernel.org/all/20240226070910.3379108-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240226130243.3820915-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240226130516.3821803-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240226130826.3824251-1-peng.fan@oss.nxp.com/
https://lore.kernel.org/all/20240219-imx-mailbox-v8-1-75535a87794e@nxp.com/
- Link to v1: https://lore.kernel.org/r/20240218-imx95-dts-v1-0-2959f89f2018@nxp.com
---
Peng Fan (3):
dt-bindings: arm: fsl: add i.MX95 19x19 EVK board
arm64: dts: freescale: add i.MX95 basic dtsi
arm64: dts: freescale: add i.MX95 19x19 EVK minimal board dts
Documentation/devicetree/bindings/arm/fsl.yaml | 6 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 111 ++
arch/arm64/boot/dts/freescale/imx95-clock.h | 187 ++++
arch/arm64/boot/dts/freescale/imx95-power.h | 55 +
arch/arm64/boot/dts/freescale/imx95.dtsi | 1152 +++++++++++++++++++++
6 files changed, 1512 insertions(+)
---
base-commit: bb7a2467e6beef44a80a17d45ebf2931e7631083
change-id: 20240428-imx95-dts-v3-bee59f0e559b
Best regards,
--
Peng Fan <peng.fan@nxp.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v3 1/3] dt-bindings: arm: fsl: add i.MX95 19x19 EVK board
2024-04-28 12:22 ` Peng Fan (OSS)
@ 2024-04-28 12:22 ` Peng Fan (OSS)
-1 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan, Conor Dooley
From: Peng Fan <peng.fan@nxp.com>
Add DT compatible string for NXP i.MX95 19x19 EVK board.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 6d185d09cb6a..5c9014087c17 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1275,6 +1275,12 @@ properties:
- fsl,imx93-11x11-evk # i.MX93 11x11 EVK Board
- const: fsl,imx93
+ - description: i.MX95 based Boards
+ items:
+ - enum:
+ - fsl,imx95-19x19-evk # i.MX95 19x19 EVK Board
+ - const: fsl,imx95
+
- description: i.MXRT1050 based Boards
items:
- enum:
--
2.37.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 1/3] dt-bindings: arm: fsl: add i.MX95 19x19 EVK board
@ 2024-04-28 12:22 ` Peng Fan (OSS)
0 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan, Conor Dooley
From: Peng Fan <peng.fan@nxp.com>
Add DT compatible string for NXP i.MX95 19x19 EVK board.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 6d185d09cb6a..5c9014087c17 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1275,6 +1275,12 @@ properties:
- fsl,imx93-11x11-evk # i.MX93 11x11 EVK Board
- const: fsl,imx93
+ - description: i.MX95 based Boards
+ items:
+ - enum:
+ - fsl,imx95-19x19-evk # i.MX95 19x19 EVK Board
+ - const: fsl,imx95
+
- description: i.MXRT1050 based Boards
items:
- enum:
--
2.37.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
2024-04-28 12:22 ` Peng Fan (OSS)
@ 2024-04-28 12:22 ` Peng Fan (OSS)
-1 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan
From: Peng Fan <peng.fan@nxp.com>
i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
and Edgelock secure enclave security. This patch is to add a minimal
dtsi, with cpu cores, coresight, scmi, gic, uart, mu, sdhc, lpi2c added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx95-clock.h | 187 +++++
arch/arm64/boot/dts/freescale/imx95-power.h | 55 ++
arch/arm64/boot/dts/freescale/imx95.dtsi | 1152 +++++++++++++++++++++++++++
3 files changed, 1394 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx95-clock.h b/arch/arm64/boot/dts/freescale/imx95-clock.h
new file mode 100644
index 000000000000..5badaace3148
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-clock.h
@@ -0,0 +1,187 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/*
+ * Copyright 2024 NXP
+ */
+
+#ifndef __CLOCK_IMX95_H
+#define __CLOCK_IMX95_H
+
+/* The index should match i.MX95 SCMI Firmware */
+#define IMX95_CLK_32K 1
+#define IMX95_CLK_24M 2
+#define IMX95_CLK_FRO 3
+#define IMX95_CLK_SYSPLL1_VCO 4
+#define IMX95_CLK_SYSPLL1_PFD0_UNGATED 5
+#define IMX95_CLK_SYSPLL1_PFD0 6
+#define IMX95_CLK_SYSPLL1_PFD0_DIV2 7
+#define IMX95_CLK_SYSPLL1_PFD1_UNGATED 8
+#define IMX95_CLK_SYSPLL1_PFD1 9
+#define IMX95_CLK_SYSPLL1_PFD1_DIV2 10
+#define IMX95_CLK_SYSPLL1_PFD2_UNGATED 11
+#define IMX95_CLK_SYSPLL1_PFD2 12
+#define IMX95_CLK_SYSPLL1_PFD2_DIV2 13
+#define IMX95_CLK_AUDIOPLL1_VCO 14
+#define IMX95_CLK_AUDIOPLL1 15
+#define IMX95_CLK_AUDIOPLL2_VCO 16
+#define IMX95_CLK_AUDIOPLL2 17
+#define IMX95_CLK_VIDEOPLL1_VCO 18
+#define IMX95_CLK_VIDEOPLL1 19
+#define IMX95_CLK_RESERVED20 20
+#define IMX95_CLK_RESERVED21 21
+#define IMX95_CLK_RESERVED22 22
+#define IMX95_CLK_RESERVED23 23
+#define IMX95_CLK_ARMPLL_VCO 24
+#define IMX95_CLK_ARMPLL_PFD0_UNGATED 25
+#define IMX95_CLK_ARMPLL_PFD0 26
+#define IMX95_CLK_ARMPLL_PFD1_UNGATED 27
+#define IMX95_CLK_ARMPLL_PFD1 28
+#define IMX95_CLK_ARMPLL_PFD2_UNGATED 29
+#define IMX95_CLK_ARMPLL_PFD2 30
+#define IMX95_CLK_ARMPLL_PFD3_UNGATED 31
+#define IMX95_CLK_ARMPLL_PFD3 32
+#define IMX95_CLK_DRAMPLL_VCO 33
+#define IMX95_CLK_DRAMPLL 34
+#define IMX95_CLK_HSIOPLL_VCO 35
+#define IMX95_CLK_HSIOPLL 36
+#define IMX95_CLK_LDBPLL_VCO 37
+#define IMX95_CLK_LDBPLL 38
+#define IMX95_CLK_EXT1 39
+#define IMX95_CLK_EXT2 40
+
+#define IMX95_CCM_NUM_CLK_SRC 41
+
+#define IMX95_CLK_ADC (IMX95_CCM_NUM_CLK_SRC + 0)
+#define IMX95_CLK_TMU (IMX95_CCM_NUM_CLK_SRC + 1)
+#define IMX95_CLK_BUSAON (IMX95_CCM_NUM_CLK_SRC + 2)
+#define IMX95_CLK_CAN1 (IMX95_CCM_NUM_CLK_SRC + 3)
+#define IMX95_CLK_I3C1 (IMX95_CCM_NUM_CLK_SRC + 4)
+#define IMX95_CLK_I3C1SLOW (IMX95_CCM_NUM_CLK_SRC + 5)
+#define IMX95_CLK_LPI2C1 (IMX95_CCM_NUM_CLK_SRC + 6)
+#define IMX95_CLK_LPI2C2 (IMX95_CCM_NUM_CLK_SRC + 7)
+#define IMX95_CLK_LPSPI1 (IMX95_CCM_NUM_CLK_SRC + 8)
+#define IMX95_CLK_LPSPI2 (IMX95_CCM_NUM_CLK_SRC + 9)
+#define IMX95_CLK_LPTMR1 (IMX95_CCM_NUM_CLK_SRC + 10)
+#define IMX95_CLK_LPUART1 (IMX95_CCM_NUM_CLK_SRC + 11)
+#define IMX95_CLK_LPUART2 (IMX95_CCM_NUM_CLK_SRC + 12)
+#define IMX95_CLK_M33 (IMX95_CCM_NUM_CLK_SRC + 13)
+#define IMX95_CLK_M33SYSTICK (IMX95_CCM_NUM_CLK_SRC + 14)
+#define IMX95_CLK_MQS1 (IMX95_CCM_NUM_CLK_SRC + 15)
+#define IMX95_CLK_PDM (IMX95_CCM_NUM_CLK_SRC + 16)
+#define IMX95_CLK_SAI1 (IMX95_CCM_NUM_CLK_SRC + 17)
+#define IMX95_CLK_SENTINEL (IMX95_CCM_NUM_CLK_SRC + 18)
+#define IMX95_CLK_TPM2 (IMX95_CCM_NUM_CLK_SRC + 19)
+#define IMX95_CLK_TSTMR1 (IMX95_CCM_NUM_CLK_SRC + 20)
+#define IMX95_CLK_CAMAPB (IMX95_CCM_NUM_CLK_SRC + 21)
+#define IMX95_CLK_CAMAXI (IMX95_CCM_NUM_CLK_SRC + 22)
+#define IMX95_CLK_CAMCM0 (IMX95_CCM_NUM_CLK_SRC + 23)
+#define IMX95_CLK_CAMISI (IMX95_CCM_NUM_CLK_SRC + 24)
+#define IMX95_CLK_MIPIPHYCFG (IMX95_CCM_NUM_CLK_SRC + 25)
+#define IMX95_CLK_MIPIPHYPLLBYPASS (IMX95_CCM_NUM_CLK_SRC + 26)
+#define IMX95_CLK_MIPIPHYPLLREF (IMX95_CCM_NUM_CLK_SRC + 27)
+#define IMX95_CLK_MIPITESTBYTE (IMX95_CCM_NUM_CLK_SRC + 28)
+#define IMX95_CLK_A55 (IMX95_CCM_NUM_CLK_SRC + 29)
+#define IMX95_CLK_A55MTRBUS (IMX95_CCM_NUM_CLK_SRC + 30)
+#define IMX95_CLK_A55PERIPH (IMX95_CCM_NUM_CLK_SRC + 31)
+#define IMX95_CLK_DRAMALT (IMX95_CCM_NUM_CLK_SRC + 32)
+#define IMX95_CLK_DRAMAPB (IMX95_CCM_NUM_CLK_SRC + 33)
+#define IMX95_CLK_DISPAPB (IMX95_CCM_NUM_CLK_SRC + 34)
+#define IMX95_CLK_DISPAXI (IMX95_CCM_NUM_CLK_SRC + 35)
+#define IMX95_CLK_DISPDP (IMX95_CCM_NUM_CLK_SRC + 36)
+#define IMX95_CLK_DISPOCRAM (IMX95_CCM_NUM_CLK_SRC + 37)
+#define IMX95_CLK_DISPUSB31 (IMX95_CCM_NUM_CLK_SRC + 38)
+#define IMX95_CLK_DISP1PIX (IMX95_CCM_NUM_CLK_SRC + 39)
+#define IMX95_CLK_DISP2PIX (IMX95_CCM_NUM_CLK_SRC + 40)
+#define IMX95_CLK_DISP3PIX (IMX95_CCM_NUM_CLK_SRC + 41)
+#define IMX95_CLK_GPUAPB (IMX95_CCM_NUM_CLK_SRC + 42)
+#define IMX95_CLK_GPU (IMX95_CCM_NUM_CLK_SRC + 43)
+#define IMX95_CLK_HSIOACSCAN480M (IMX95_CCM_NUM_CLK_SRC + 44)
+#define IMX95_CLK_HSIOACSCAN80M (IMX95_CCM_NUM_CLK_SRC + 45)
+#define IMX95_CLK_HSIO (IMX95_CCM_NUM_CLK_SRC + 46)
+#define IMX95_CLK_HSIOPCIEAUX (IMX95_CCM_NUM_CLK_SRC + 47)
+#define IMX95_CLK_HSIOPCIETEST160M (IMX95_CCM_NUM_CLK_SRC + 48)
+#define IMX95_CLK_HSIOPCIETEST400M (IMX95_CCM_NUM_CLK_SRC + 49)
+#define IMX95_CLK_HSIOPCIETEST500M (IMX95_CCM_NUM_CLK_SRC + 50)
+#define IMX95_CLK_HSIOUSBTEST50M (IMX95_CCM_NUM_CLK_SRC + 51)
+#define IMX95_CLK_HSIOUSBTEST60M (IMX95_CCM_NUM_CLK_SRC + 52)
+#define IMX95_CLK_BUSM7 (IMX95_CCM_NUM_CLK_SRC + 53)
+#define IMX95_CLK_M7 (IMX95_CCM_NUM_CLK_SRC + 54)
+#define IMX95_CLK_M7SYSTICK (IMX95_CCM_NUM_CLK_SRC + 55)
+#define IMX95_CLK_BUSNETCMIX (IMX95_CCM_NUM_CLK_SRC + 56)
+#define IMX95_CLK_ENET (IMX95_CCM_NUM_CLK_SRC + 57)
+#define IMX95_CLK_ENETPHYTEST200M (IMX95_CCM_NUM_CLK_SRC + 58)
+#define IMX95_CLK_ENETPHYTEST500M (IMX95_CCM_NUM_CLK_SRC + 59)
+#define IMX95_CLK_ENETPHYTEST667M (IMX95_CCM_NUM_CLK_SRC + 60)
+#define IMX95_CLK_ENETREF (IMX95_CCM_NUM_CLK_SRC + 61)
+#define IMX95_CLK_ENETTIMER1 (IMX95_CCM_NUM_CLK_SRC + 62)
+#define IMX95_CLK_MQS2 (IMX95_CCM_NUM_CLK_SRC + 63)
+#define IMX95_CLK_SAI2 (IMX95_CCM_NUM_CLK_SRC + 64)
+#define IMX95_CLK_NOCAPB (IMX95_CCM_NUM_CLK_SRC + 65)
+#define IMX95_CLK_NOC (IMX95_CCM_NUM_CLK_SRC + 66)
+#define IMX95_CLK_NPUAPB (IMX95_CCM_NUM_CLK_SRC + 67)
+#define IMX95_CLK_NPU (IMX95_CCM_NUM_CLK_SRC + 68)
+#define IMX95_CLK_CCMCKO1 (IMX95_CCM_NUM_CLK_SRC + 69)
+#define IMX95_CLK_CCMCKO2 (IMX95_CCM_NUM_CLK_SRC + 70)
+#define IMX95_CLK_CCMCKO3 (IMX95_CCM_NUM_CLK_SRC + 71)
+#define IMX95_CLK_CCMCKO4 (IMX95_CCM_NUM_CLK_SRC + 72)
+#define IMX95_CLK_VPUAPB (IMX95_CCM_NUM_CLK_SRC + 73)
+#define IMX95_CLK_VPU (IMX95_CCM_NUM_CLK_SRC + 74)
+#define IMX95_CLK_VPUDSP (IMX95_CCM_NUM_CLK_SRC + 75)
+#define IMX95_CLK_VPUJPEG (IMX95_CCM_NUM_CLK_SRC + 76)
+#define IMX95_CLK_AUDIOXCVR (IMX95_CCM_NUM_CLK_SRC + 77)
+#define IMX95_CLK_BUSWAKEUP (IMX95_CCM_NUM_CLK_SRC + 78)
+#define IMX95_CLK_CAN2 (IMX95_CCM_NUM_CLK_SRC + 79)
+#define IMX95_CLK_CAN3 (IMX95_CCM_NUM_CLK_SRC + 80)
+#define IMX95_CLK_CAN4 (IMX95_CCM_NUM_CLK_SRC + 81)
+#define IMX95_CLK_CAN5 (IMX95_CCM_NUM_CLK_SRC + 82)
+#define IMX95_CLK_FLEXIO1 (IMX95_CCM_NUM_CLK_SRC + 83)
+#define IMX95_CLK_FLEXIO2 (IMX95_CCM_NUM_CLK_SRC + 84)
+#define IMX95_CLK_FLEXSPI1 (IMX95_CCM_NUM_CLK_SRC + 85)
+#define IMX95_CLK_I3C2 (IMX95_CCM_NUM_CLK_SRC + 86)
+#define IMX95_CLK_I3C2SLOW (IMX95_CCM_NUM_CLK_SRC + 87)
+#define IMX95_CLK_LPI2C3 (IMX95_CCM_NUM_CLK_SRC + 88)
+#define IMX95_CLK_LPI2C4 (IMX95_CCM_NUM_CLK_SRC + 89)
+#define IMX95_CLK_LPI2C5 (IMX95_CCM_NUM_CLK_SRC + 90)
+#define IMX95_CLK_LPI2C6 (IMX95_CCM_NUM_CLK_SRC + 91)
+#define IMX95_CLK_LPI2C7 (IMX95_CCM_NUM_CLK_SRC + 92)
+#define IMX95_CLK_LPI2C8 (IMX95_CCM_NUM_CLK_SRC + 93)
+#define IMX95_CLK_LPSPI3 (IMX95_CCM_NUM_CLK_SRC + 94)
+#define IMX95_CLK_LPSPI4 (IMX95_CCM_NUM_CLK_SRC + 95)
+#define IMX95_CLK_LPSPI5 (IMX95_CCM_NUM_CLK_SRC + 96)
+#define IMX95_CLK_LPSPI6 (IMX95_CCM_NUM_CLK_SRC + 97)
+#define IMX95_CLK_LPSPI7 (IMX95_CCM_NUM_CLK_SRC + 98)
+#define IMX95_CLK_LPSPI8 (IMX95_CCM_NUM_CLK_SRC + 99)
+#define IMX95_CLK_LPTMR2 (IMX95_CCM_NUM_CLK_SRC + 100)
+#define IMX95_CLK_LPUART3 (IMX95_CCM_NUM_CLK_SRC + 101)
+#define IMX95_CLK_LPUART4 (IMX95_CCM_NUM_CLK_SRC + 102)
+#define IMX95_CLK_LPUART5 (IMX95_CCM_NUM_CLK_SRC + 103)
+#define IMX95_CLK_LPUART6 (IMX95_CCM_NUM_CLK_SRC + 104)
+#define IMX95_CLK_LPUART7 (IMX95_CCM_NUM_CLK_SRC + 105)
+#define IMX95_CLK_LPUART8 (IMX95_CCM_NUM_CLK_SRC + 106)
+#define IMX95_CLK_SAI3 (IMX95_CCM_NUM_CLK_SRC + 107)
+#define IMX95_CLK_SAI4 (IMX95_CCM_NUM_CLK_SRC + 108)
+#define IMX95_CLK_SAI5 (IMX95_CCM_NUM_CLK_SRC + 109)
+#define IMX95_CLK_SPDIF (IMX95_CCM_NUM_CLK_SRC + 110)
+#define IMX95_CLK_SWOTRACE (IMX95_CCM_NUM_CLK_SRC + 111)
+#define IMX95_CLK_TPM4 (IMX95_CCM_NUM_CLK_SRC + 112)
+#define IMX95_CLK_TPM5 (IMX95_CCM_NUM_CLK_SRC + 113)
+#define IMX95_CLK_TPM6 (IMX95_CCM_NUM_CLK_SRC + 114)
+#define IMX95_CLK_TSTMR2 (IMX95_CCM_NUM_CLK_SRC + 115)
+#define IMX95_CLK_USBPHYBURUNIN (IMX95_CCM_NUM_CLK_SRC + 116)
+#define IMX95_CLK_USDHC1 (IMX95_CCM_NUM_CLK_SRC + 117)
+#define IMX95_CLK_USDHC2 (IMX95_CCM_NUM_CLK_SRC + 118)
+#define IMX95_CLK_USDHC3 (IMX95_CCM_NUM_CLK_SRC + 119)
+#define IMX95_CLK_V2XPK (IMX95_CCM_NUM_CLK_SRC + 120)
+#define IMX95_CLK_WAKEUPAXI (IMX95_CCM_NUM_CLK_SRC + 121)
+#define IMX95_CLK_XSPISLVROOT (IMX95_CCM_NUM_CLK_SRC + 122)
+#define IMX95_CLK_SEL_EXT (IMX95_CCM_NUM_CLK_SRC + 123 + 0)
+#define IMX95_CLK_SEL_A55C0 (IMX95_CCM_NUM_CLK_SRC + 123 + 1)
+#define IMX95_CLK_SEL_A55C1 (IMX95_CCM_NUM_CLK_SRC + 123 + 2)
+#define IMX95_CLK_SEL_A55C2 (IMX95_CCM_NUM_CLK_SRC + 123 + 3)
+#define IMX95_CLK_SEL_A55C3 (IMX95_CCM_NUM_CLK_SRC + 123 + 4)
+#define IMX95_CLK_SEL_A55C4 (IMX95_CCM_NUM_CLK_SRC + 123 + 5)
+#define IMX95_CLK_SEL_A55C5 (IMX95_CCM_NUM_CLK_SRC + 123 + 6)
+#define IMX95_CLK_SEL_A55P (IMX95_CCM_NUM_CLK_SRC + 123 + 7)
+#define IMX95_CLK_SEL_DRAM (IMX95_CCM_NUM_CLK_SRC + 123 + 8)
+#define IMX95_CLK_SEL_TEMPSENSE (IMX95_CCM_NUM_CLK_SRC + 123 + 9)
+
+#endif /* __DT_BINDINGS_CLOCK_IMX95_H */
diff --git a/arch/arm64/boot/dts/freescale/imx95-power.h b/arch/arm64/boot/dts/freescale/imx95-power.h
new file mode 100644
index 000000000000..a43779317fed
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-power.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Copyright 2024 NXP
+ */
+
+#ifndef __IMX95_POWER_H__
+#define __IMX95_POWER_H__
+
+#define IMX95_PD_ANA 0
+#define IMX95_PD_AON 1
+#define IMX95_PD_BBSM 2
+#define IMX95_PD_CAMERA 3
+#define IMX95_PD_CCMSRCGPC 4
+#define IMX95_PD_A55C0 5
+#define IMX95_PD_A55C1 6
+#define IMX95_PD_A55C2 7
+#define IMX95_PD_A55C3 8
+#define IMX95_PD_A55C4 9
+#define IMX95_PD_A55C5 10
+#define IMX95_PD_A55P 11
+#define IMX95_PD_DDR 12
+#define IMX95_PD_DISPLAY 13
+#define IMX95_PD_GPU 14
+#define IMX95_PD_HSIO_TOP 15
+#define IMX95_PD_HSIO_WAON 16
+#define IMX95_PD_M7 17
+#define IMX95_PD_NETC 18
+#define IMX95_PD_NOC 19
+#define IMX95_PD_NPU 20
+#define IMX95_PD_VPU 21
+#define IMX95_PD_WAKEUP 22
+
+#define IMX95_PERF_ELE 0
+#define IMX95_PERF_M33 1
+#define IMX95_PERF_WAKEUP 2
+#define IMX95_PERF_M7 3
+#define IMX95_PERF_DRAM 4
+#define IMX95_PERF_HSIO 5
+#define IMX95_PERF_NPU 6
+#define IMX95_PERF_NOC 7
+#define IMX95_PERF_A55 8
+#define IMX95_PERF_GPU 9
+#define IMX95_PERF_VPU 10
+#define IMX95_PERF_CAM 11
+#define IMX95_PERF_DISP 12
+#define IMX95_PERF_A55PER 13
+#define IMX95_PERF_A55P 14
+#define IMX95_PERF_A55C0 15
+#define IMX95_PERF_A55C1 16
+#define IMX95_PERF_A55C2 17
+#define IMX95_PERF_A55C3 18
+#define IMX95_PERF_A55C4 19
+#define IMX95_PERF_A55C5 20
+
+#endif
diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
new file mode 100644
index 000000000000..f52023ec7f0c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -0,0 +1,1152 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2024 NXP
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "imx95-clock.h"
+#include "imx95-power.h"
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ idle-states {
+ entry-method = "psci";
+
+ cpu_pd_wait: cpu-pd-wait {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x0010033>;
+ local-timer-stop;
+ entry-latency-us = <10000>;
+ exit-latency-us = <7000>;
+ min-residency-us = <27000>;
+ wakeup-latency-us = <15000>;
+ status = "disabled";
+ };
+ };
+
+ A55_0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l0>;
+ };
+
+ A55_1: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x100>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l1>;
+ };
+
+ A55_2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x200>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l2>;
+ };
+
+ A55_3: cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x300>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l3>;
+ };
+
+ A55_4: cpu@400 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x400>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l4>;
+ };
+
+ A55_5: cpu@500 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x500>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l5>;
+ };
+
+ l2_cache_l0: l2-cache-l0 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l1: l2-cache-l1 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l2: l2-cache-l2 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l3: l2-cache-l3 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l4: l2-cache-l4 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l5: l2-cache-l5 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l3_cache: l3-cache {
+ compatible = "cache";
+ cache-size = <524288>;
+ cache-line-size = <64>;
+ cache-sets = <1024>;
+ cache-level = <3>;
+ cache-unified;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&A55_0>;
+ };
+
+ core1 {
+ cpu = <&A55_1>;
+ };
+
+ core2 {
+ cpu = <&A55_2>;
+ };
+
+ core3 {
+ cpu = <&A55_3>;
+ };
+
+ core4 {
+ cpu = <&A55_4>;
+ };
+
+ core5 {
+ cpu = <&A55_5>;
+ };
+ };
+ };
+ };
+
+ clk_ext1: clock-ext1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext1";
+ };
+
+ sai1_mclk: sai-mclk1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai1_mclk";
+ };
+
+ sai2_mclk: sai-mclk2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai2_mclk";
+ };
+
+ sai3_mclk: sai-mclk3 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai3_mclk";
+ };
+
+ sai4_mclk: sai-mclk4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai4_mclk";
+ };
+
+ sai5_mclk: sai-mclk5 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai5_mclk";
+ };
+
+ osc_24m: osc-24m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc_24m";
+ };
+
+ sram1: sram@20480000 {
+ compatible = "mmio-sram";
+ reg = <0x0 0x204c0000 0x0 0x18000>;
+ ranges = <0x0 0x0 0x204c0000 0x18000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ firmware {
+ scmi {
+ compatible = "arm,scmi";
+ mboxes = <&mu2 5 0>, <&mu2 3 0>, <&mu2 3 1>;
+ shmem = <&scmi_buf0>, <&scmi_buf1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ scmi_devpd: protocol@11 {
+ reg = <0x11>;
+ #power-domain-cells = <1>;
+ };
+
+ scmi_perf: protocol@13 {
+ reg = <0x13>;
+ #power-domain-cells = <1>;
+ };
+
+ scmi_clk: protocol@14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+
+ scmi_sensor: protocol@15 {
+ reg = <0x15>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
+
+ pmu {
+ compatible = "arm,cortex-a55-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ thermal-zones {
+ a55-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&scmi_sensor 1>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&A55_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
+ etm0: etm@40840000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0x0 0x40840000 0x0 0x10000>;
+ arm,primecell-periphid = <0xbb95d>;
+ cpu = <&A55_0>;
+ clocks = <&scmi_clk IMX95_CLK_A55PERIPH>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+
+ out-ports {
+ port {
+ etm0_out_port: endpoint {
+ remote-endpoint = <&ca_funnel_in_port0>;
+ };
+ };
+ };
+ };
+
+ funnel0: funnel {
+ /*
+ * non-configurable funnel don't show up on the AMBA
+ * bus. As such no need to add "arm,primecell".
+ */
+ compatible = "arm,coresight-static-funnel";
+ status = "disabled";
+
+ in-ports {
+ port {
+ ca_funnel_in_port0: endpoint {
+ remote-endpoint = <&etm0_out_port>;
+ };
+ };
+ };
+
+ out-ports {
+ port {
+ ca_funnel_out_port0: endpoint {
+ remote-endpoint = <&hugo_funnel_in_port0>;
+ };
+ };
+ };
+ };
+
+ funnel1: funnel_sys {
+ compatible = "arm,coresight-static-funnel";
+ status = "disabled";
+
+ in-ports {
+ port {
+ hugo_funnel_in_port0: endpoint {
+ remote-endpoint = <&ca_funnel_out_port0>;
+ };
+ };
+ };
+
+ out-ports {
+ port {
+ hugo_funnel_out_port0: endpoint {
+ remote-endpoint = <&etf_in_port>;
+ };
+ };
+ };
+ };
+
+ etf: etf@41030000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x0 0x41030000 0x0 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_A55PERIPH>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+
+ in-ports {
+ port {
+ etf_in_port: endpoint {
+ remote-endpoint = <&hugo_funnel_out_port0>;
+ };
+ };
+ };
+
+ out-ports {
+ port {
+ etf_out_port: endpoint {
+ remote-endpoint = <&etr_in_port>;
+ };
+ };
+ };
+ };
+
+ etr: etr@41040000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x0 0x41040000 0x0 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_A55PERIPH>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+
+ in-ports {
+ port {
+ etr_in_port: endpoint {
+ remote-endpoint = <&etf_out_port>;
+ };
+ };
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,no-tick-in-suspend;
+ interrupt-parent = <&gic>;
+ };
+
+ gic: interrupt-controller@48000000 {
+ compatible = "arm,gic-v3";
+ reg = <0 0x48000000 0 0x10000>,
+ <0 0x48060000 0 0xc0000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ dma-noncoherent;
+ ranges;
+
+ its: msi-controller@48040000 {
+ compatible = "arm,gic-v3-its";
+ reg = <0 0x48040000 0 0x20000>;
+ msi-controller;
+ #msi-cells = <1>;
+ dma-noncoherent;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ aips2: bus@42000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x0 0x42000000 0x0 0x800000>;
+ ranges = <0x42000000 0x0 0x42000000 0x8000000>,
+ <0x28000000 0x0 0x28000000 0x10000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mu7: mailbox@42430000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x42430000 0x10000>;
+ interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu8: mailbox@42730000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x42730000 0x10000>;
+ interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ wdog3: watchdog@42490000 {
+ compatible = "fsl,imx93-wdt";
+ reg = <0x42490000 0x10000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ timeout-sec = <40>;
+ fsl,ext-reset-output;
+ status = "disabled";
+ };
+
+ tpm3: pwm@424e0000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x424e0000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm4: pwm@424f0000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x424f0000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM4>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm5: pwm@42500000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x42500000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM5>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm6: pwm@42510000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x42510000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM6>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ lpi2c3: i2c@42530000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x42530000 0x10000>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C3>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c4: i2c@42540000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x42540000 0x10000>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C4>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi3: spi@42550000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42550000 0x10000>;
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI3>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi4: spi@42560000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42560000 0x10000>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI4>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpuart3: serial@42570000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42570000 0x1000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART3>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart4: serial@42580000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42580000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART4>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart5: serial@42590000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42590000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART5>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart6: serial@425a0000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x425a0000 0x1000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART6>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart7: serial@42690000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42690000 0x1000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART7>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart8: serial@426a0000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x426a0000 0x1000>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART8>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpi2c5: i2c@426b0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426b0000 0x10000>;
+ interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C5>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c6: i2c@426c0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426c0000 0x10000>;
+ interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C6>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c7: i2c@426d0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426d0000 0x10000>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C7>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c8: i2c@426e0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426e0000 0x10000>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C8>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi5: spi@426f0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x426f0000 0x10000>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI5>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi6: spi@42700000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42700000 0x10000>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI6>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi7: spi@42710000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42710000 0x10000>;
+ interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI7>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi8: spi@42720000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42720000 0x10000>;
+ interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI8>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+ };
+
+ aips3: bus@42800000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0 0x42800000 0 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x42800000 0x0 0x42800000 0x800000>;
+
+ usdhc1: mmc@42850000 {
+ compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
+ reg = <0x42850000 0x10000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_WAKEUPAXI>,
+ <&scmi_clk IMX95_CLK_USDHC1>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&scmi_clk IMX95_CLK_USDHC1>;
+ assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ fsl,tuning-start-tap = <1>;
+ fsl,tuning-step= <2>;
+ status = "disabled";
+ };
+
+ usdhc2: mmc@42860000 {
+ compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
+ reg = <0x42860000 0x10000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_WAKEUPAXI>,
+ <&scmi_clk IMX95_CLK_USDHC2>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&scmi_clk IMX95_CLK_USDHC2>;
+ assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
+ assigned-clock-rates = <200000000>;
+ bus-width = <4>;
+ fsl,tuning-start-tap = <1>;
+ fsl,tuning-step= <2>;
+ status = "disabled";
+ };
+
+ usdhc3: mmc@428b0000 {
+ compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
+ reg = <0x428b0000 0x10000>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_WAKEUPAXI>,
+ <&scmi_clk IMX95_CLK_USDHC3>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ fsl,tuning-start-tap = <1>;
+ fsl,tuning-step= <2>;
+ status = "disabled";
+ };
+ };
+
+ gpio2: gpio@43810000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43810000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ gpio3: gpio@43820000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43820000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ gpio4: gpio@43840000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43840000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ gpio5: gpio@43850000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43850000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ aips1: bus@44000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x0 0x44000000 0x0 0x800000>;
+ ranges = <0x44000000 0x0 0x44000000 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mu1: mailbox@44220000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x44220000 0x10000>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu2: mailbox@445b0000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x445b0000 0x1000>;
+ ranges;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #mbox-cells = <2>;
+
+ sram0: sram@445b1000 {
+ compatible = "mmio-sram";
+ reg = <0x445b1000 0x400>;
+ ranges = <0x0 0x445b1000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ scmi_buf0: scmi-sram-section@0 {
+ compatible = "arm,scmi-shmem";
+ reg = <0x0 0x80>;
+ };
+
+ scmi_buf1: scmi-sram-section@80 {
+ compatible = "arm,scmi-shmem";
+ reg = <0x80 0x80>;
+ };
+ };
+
+ };
+
+ mu3: mailbox@445d0000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x445d0000 0x10000>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu4: mailbox@445f0000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x445f0000 0x10000>;
+ interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu6: mailbox@44630000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x44630000 0x10000>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ tpm1: pwm@44310000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x44310000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm2: pwm@44320000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x44320000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM2>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ lpi2c1: i2c@44340000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x44340000 0x10000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C1>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c2: i2c@44350000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x44350000 0x10000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C2>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi1: spi@44360000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x44360000 0x10000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi2: spi@44370000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x44370000 0x10000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpuart1: serial@44380000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x44380000 0x1000>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart2: serial@44390000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x44390000 0x1000>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART2>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ adc1: adc@44530000 {
+ compatible = "nxp,imx93-adc";
+ reg = <0x44530000 0x10000>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_ADC>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ };
+
+ aips4: bus@49000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x0 0x49000000 0x0 0x800000>;
+ ranges = <0x49000000 0x0 0x49000000 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ smmu: iommu@490d0000 {
+ compatible = "arm,smmu-v3";
+ reg = <0x490d0000 0x100000>;
+ interrupts = <GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 334 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 326 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "eventq", "gerror", "priq", "cmdq-sync";
+ #iommu-cells = <1>;
+ status = "disabled";
+ };
+ };
+
+ gpio1: gpio@47400000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x47400000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_M33>,
+ <&scmi_clk IMX95_CLK_M33>;
+ clock-names = "gpio", "port";
+ status = "disabled";
+ };
+
+ elemu0: mailbox@47520000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47520000 0x0 0x10000>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu1: mailbox@47530000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47530000 0x0 0x10000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu2: mailbox@47540000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47540000 0x0 0x10000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu3: mailbox@47550000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47550000 0x0 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ };
+
+ elemu4: mailbox@47560000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47560000 0x0 0x10000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu5: mailbox@47570000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47570000 0x0 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ v2x_mu: mailbox@47350000 {
+ compatible = "fsl,imx95-mu-v2x";
+ reg = <0x0 0x47350000 0x0 0x10000>;
+ interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ };
+
+ v2x_mu6: mailbox@47320000 {
+ compatible = "fsl,imx95-mu-v2x";
+ reg = <0x0 0x47320000 0x0 0x10000>;
+ interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ };
+ };
+};
--
2.37.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
@ 2024-04-28 12:22 ` Peng Fan (OSS)
0 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan
From: Peng Fan <peng.fan@nxp.com>
i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
and Edgelock secure enclave security. This patch is to add a minimal
dtsi, with cpu cores, coresight, scmi, gic, uart, mu, sdhc, lpi2c added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/imx95-clock.h | 187 +++++
arch/arm64/boot/dts/freescale/imx95-power.h | 55 ++
arch/arm64/boot/dts/freescale/imx95.dtsi | 1152 +++++++++++++++++++++++++++
3 files changed, 1394 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx95-clock.h b/arch/arm64/boot/dts/freescale/imx95-clock.h
new file mode 100644
index 000000000000..5badaace3148
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-clock.h
@@ -0,0 +1,187 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/*
+ * Copyright 2024 NXP
+ */
+
+#ifndef __CLOCK_IMX95_H
+#define __CLOCK_IMX95_H
+
+/* The index should match i.MX95 SCMI Firmware */
+#define IMX95_CLK_32K 1
+#define IMX95_CLK_24M 2
+#define IMX95_CLK_FRO 3
+#define IMX95_CLK_SYSPLL1_VCO 4
+#define IMX95_CLK_SYSPLL1_PFD0_UNGATED 5
+#define IMX95_CLK_SYSPLL1_PFD0 6
+#define IMX95_CLK_SYSPLL1_PFD0_DIV2 7
+#define IMX95_CLK_SYSPLL1_PFD1_UNGATED 8
+#define IMX95_CLK_SYSPLL1_PFD1 9
+#define IMX95_CLK_SYSPLL1_PFD1_DIV2 10
+#define IMX95_CLK_SYSPLL1_PFD2_UNGATED 11
+#define IMX95_CLK_SYSPLL1_PFD2 12
+#define IMX95_CLK_SYSPLL1_PFD2_DIV2 13
+#define IMX95_CLK_AUDIOPLL1_VCO 14
+#define IMX95_CLK_AUDIOPLL1 15
+#define IMX95_CLK_AUDIOPLL2_VCO 16
+#define IMX95_CLK_AUDIOPLL2 17
+#define IMX95_CLK_VIDEOPLL1_VCO 18
+#define IMX95_CLK_VIDEOPLL1 19
+#define IMX95_CLK_RESERVED20 20
+#define IMX95_CLK_RESERVED21 21
+#define IMX95_CLK_RESERVED22 22
+#define IMX95_CLK_RESERVED23 23
+#define IMX95_CLK_ARMPLL_VCO 24
+#define IMX95_CLK_ARMPLL_PFD0_UNGATED 25
+#define IMX95_CLK_ARMPLL_PFD0 26
+#define IMX95_CLK_ARMPLL_PFD1_UNGATED 27
+#define IMX95_CLK_ARMPLL_PFD1 28
+#define IMX95_CLK_ARMPLL_PFD2_UNGATED 29
+#define IMX95_CLK_ARMPLL_PFD2 30
+#define IMX95_CLK_ARMPLL_PFD3_UNGATED 31
+#define IMX95_CLK_ARMPLL_PFD3 32
+#define IMX95_CLK_DRAMPLL_VCO 33
+#define IMX95_CLK_DRAMPLL 34
+#define IMX95_CLK_HSIOPLL_VCO 35
+#define IMX95_CLK_HSIOPLL 36
+#define IMX95_CLK_LDBPLL_VCO 37
+#define IMX95_CLK_LDBPLL 38
+#define IMX95_CLK_EXT1 39
+#define IMX95_CLK_EXT2 40
+
+#define IMX95_CCM_NUM_CLK_SRC 41
+
+#define IMX95_CLK_ADC (IMX95_CCM_NUM_CLK_SRC + 0)
+#define IMX95_CLK_TMU (IMX95_CCM_NUM_CLK_SRC + 1)
+#define IMX95_CLK_BUSAON (IMX95_CCM_NUM_CLK_SRC + 2)
+#define IMX95_CLK_CAN1 (IMX95_CCM_NUM_CLK_SRC + 3)
+#define IMX95_CLK_I3C1 (IMX95_CCM_NUM_CLK_SRC + 4)
+#define IMX95_CLK_I3C1SLOW (IMX95_CCM_NUM_CLK_SRC + 5)
+#define IMX95_CLK_LPI2C1 (IMX95_CCM_NUM_CLK_SRC + 6)
+#define IMX95_CLK_LPI2C2 (IMX95_CCM_NUM_CLK_SRC + 7)
+#define IMX95_CLK_LPSPI1 (IMX95_CCM_NUM_CLK_SRC + 8)
+#define IMX95_CLK_LPSPI2 (IMX95_CCM_NUM_CLK_SRC + 9)
+#define IMX95_CLK_LPTMR1 (IMX95_CCM_NUM_CLK_SRC + 10)
+#define IMX95_CLK_LPUART1 (IMX95_CCM_NUM_CLK_SRC + 11)
+#define IMX95_CLK_LPUART2 (IMX95_CCM_NUM_CLK_SRC + 12)
+#define IMX95_CLK_M33 (IMX95_CCM_NUM_CLK_SRC + 13)
+#define IMX95_CLK_M33SYSTICK (IMX95_CCM_NUM_CLK_SRC + 14)
+#define IMX95_CLK_MQS1 (IMX95_CCM_NUM_CLK_SRC + 15)
+#define IMX95_CLK_PDM (IMX95_CCM_NUM_CLK_SRC + 16)
+#define IMX95_CLK_SAI1 (IMX95_CCM_NUM_CLK_SRC + 17)
+#define IMX95_CLK_SENTINEL (IMX95_CCM_NUM_CLK_SRC + 18)
+#define IMX95_CLK_TPM2 (IMX95_CCM_NUM_CLK_SRC + 19)
+#define IMX95_CLK_TSTMR1 (IMX95_CCM_NUM_CLK_SRC + 20)
+#define IMX95_CLK_CAMAPB (IMX95_CCM_NUM_CLK_SRC + 21)
+#define IMX95_CLK_CAMAXI (IMX95_CCM_NUM_CLK_SRC + 22)
+#define IMX95_CLK_CAMCM0 (IMX95_CCM_NUM_CLK_SRC + 23)
+#define IMX95_CLK_CAMISI (IMX95_CCM_NUM_CLK_SRC + 24)
+#define IMX95_CLK_MIPIPHYCFG (IMX95_CCM_NUM_CLK_SRC + 25)
+#define IMX95_CLK_MIPIPHYPLLBYPASS (IMX95_CCM_NUM_CLK_SRC + 26)
+#define IMX95_CLK_MIPIPHYPLLREF (IMX95_CCM_NUM_CLK_SRC + 27)
+#define IMX95_CLK_MIPITESTBYTE (IMX95_CCM_NUM_CLK_SRC + 28)
+#define IMX95_CLK_A55 (IMX95_CCM_NUM_CLK_SRC + 29)
+#define IMX95_CLK_A55MTRBUS (IMX95_CCM_NUM_CLK_SRC + 30)
+#define IMX95_CLK_A55PERIPH (IMX95_CCM_NUM_CLK_SRC + 31)
+#define IMX95_CLK_DRAMALT (IMX95_CCM_NUM_CLK_SRC + 32)
+#define IMX95_CLK_DRAMAPB (IMX95_CCM_NUM_CLK_SRC + 33)
+#define IMX95_CLK_DISPAPB (IMX95_CCM_NUM_CLK_SRC + 34)
+#define IMX95_CLK_DISPAXI (IMX95_CCM_NUM_CLK_SRC + 35)
+#define IMX95_CLK_DISPDP (IMX95_CCM_NUM_CLK_SRC + 36)
+#define IMX95_CLK_DISPOCRAM (IMX95_CCM_NUM_CLK_SRC + 37)
+#define IMX95_CLK_DISPUSB31 (IMX95_CCM_NUM_CLK_SRC + 38)
+#define IMX95_CLK_DISP1PIX (IMX95_CCM_NUM_CLK_SRC + 39)
+#define IMX95_CLK_DISP2PIX (IMX95_CCM_NUM_CLK_SRC + 40)
+#define IMX95_CLK_DISP3PIX (IMX95_CCM_NUM_CLK_SRC + 41)
+#define IMX95_CLK_GPUAPB (IMX95_CCM_NUM_CLK_SRC + 42)
+#define IMX95_CLK_GPU (IMX95_CCM_NUM_CLK_SRC + 43)
+#define IMX95_CLK_HSIOACSCAN480M (IMX95_CCM_NUM_CLK_SRC + 44)
+#define IMX95_CLK_HSIOACSCAN80M (IMX95_CCM_NUM_CLK_SRC + 45)
+#define IMX95_CLK_HSIO (IMX95_CCM_NUM_CLK_SRC + 46)
+#define IMX95_CLK_HSIOPCIEAUX (IMX95_CCM_NUM_CLK_SRC + 47)
+#define IMX95_CLK_HSIOPCIETEST160M (IMX95_CCM_NUM_CLK_SRC + 48)
+#define IMX95_CLK_HSIOPCIETEST400M (IMX95_CCM_NUM_CLK_SRC + 49)
+#define IMX95_CLK_HSIOPCIETEST500M (IMX95_CCM_NUM_CLK_SRC + 50)
+#define IMX95_CLK_HSIOUSBTEST50M (IMX95_CCM_NUM_CLK_SRC + 51)
+#define IMX95_CLK_HSIOUSBTEST60M (IMX95_CCM_NUM_CLK_SRC + 52)
+#define IMX95_CLK_BUSM7 (IMX95_CCM_NUM_CLK_SRC + 53)
+#define IMX95_CLK_M7 (IMX95_CCM_NUM_CLK_SRC + 54)
+#define IMX95_CLK_M7SYSTICK (IMX95_CCM_NUM_CLK_SRC + 55)
+#define IMX95_CLK_BUSNETCMIX (IMX95_CCM_NUM_CLK_SRC + 56)
+#define IMX95_CLK_ENET (IMX95_CCM_NUM_CLK_SRC + 57)
+#define IMX95_CLK_ENETPHYTEST200M (IMX95_CCM_NUM_CLK_SRC + 58)
+#define IMX95_CLK_ENETPHYTEST500M (IMX95_CCM_NUM_CLK_SRC + 59)
+#define IMX95_CLK_ENETPHYTEST667M (IMX95_CCM_NUM_CLK_SRC + 60)
+#define IMX95_CLK_ENETREF (IMX95_CCM_NUM_CLK_SRC + 61)
+#define IMX95_CLK_ENETTIMER1 (IMX95_CCM_NUM_CLK_SRC + 62)
+#define IMX95_CLK_MQS2 (IMX95_CCM_NUM_CLK_SRC + 63)
+#define IMX95_CLK_SAI2 (IMX95_CCM_NUM_CLK_SRC + 64)
+#define IMX95_CLK_NOCAPB (IMX95_CCM_NUM_CLK_SRC + 65)
+#define IMX95_CLK_NOC (IMX95_CCM_NUM_CLK_SRC + 66)
+#define IMX95_CLK_NPUAPB (IMX95_CCM_NUM_CLK_SRC + 67)
+#define IMX95_CLK_NPU (IMX95_CCM_NUM_CLK_SRC + 68)
+#define IMX95_CLK_CCMCKO1 (IMX95_CCM_NUM_CLK_SRC + 69)
+#define IMX95_CLK_CCMCKO2 (IMX95_CCM_NUM_CLK_SRC + 70)
+#define IMX95_CLK_CCMCKO3 (IMX95_CCM_NUM_CLK_SRC + 71)
+#define IMX95_CLK_CCMCKO4 (IMX95_CCM_NUM_CLK_SRC + 72)
+#define IMX95_CLK_VPUAPB (IMX95_CCM_NUM_CLK_SRC + 73)
+#define IMX95_CLK_VPU (IMX95_CCM_NUM_CLK_SRC + 74)
+#define IMX95_CLK_VPUDSP (IMX95_CCM_NUM_CLK_SRC + 75)
+#define IMX95_CLK_VPUJPEG (IMX95_CCM_NUM_CLK_SRC + 76)
+#define IMX95_CLK_AUDIOXCVR (IMX95_CCM_NUM_CLK_SRC + 77)
+#define IMX95_CLK_BUSWAKEUP (IMX95_CCM_NUM_CLK_SRC + 78)
+#define IMX95_CLK_CAN2 (IMX95_CCM_NUM_CLK_SRC + 79)
+#define IMX95_CLK_CAN3 (IMX95_CCM_NUM_CLK_SRC + 80)
+#define IMX95_CLK_CAN4 (IMX95_CCM_NUM_CLK_SRC + 81)
+#define IMX95_CLK_CAN5 (IMX95_CCM_NUM_CLK_SRC + 82)
+#define IMX95_CLK_FLEXIO1 (IMX95_CCM_NUM_CLK_SRC + 83)
+#define IMX95_CLK_FLEXIO2 (IMX95_CCM_NUM_CLK_SRC + 84)
+#define IMX95_CLK_FLEXSPI1 (IMX95_CCM_NUM_CLK_SRC + 85)
+#define IMX95_CLK_I3C2 (IMX95_CCM_NUM_CLK_SRC + 86)
+#define IMX95_CLK_I3C2SLOW (IMX95_CCM_NUM_CLK_SRC + 87)
+#define IMX95_CLK_LPI2C3 (IMX95_CCM_NUM_CLK_SRC + 88)
+#define IMX95_CLK_LPI2C4 (IMX95_CCM_NUM_CLK_SRC + 89)
+#define IMX95_CLK_LPI2C5 (IMX95_CCM_NUM_CLK_SRC + 90)
+#define IMX95_CLK_LPI2C6 (IMX95_CCM_NUM_CLK_SRC + 91)
+#define IMX95_CLK_LPI2C7 (IMX95_CCM_NUM_CLK_SRC + 92)
+#define IMX95_CLK_LPI2C8 (IMX95_CCM_NUM_CLK_SRC + 93)
+#define IMX95_CLK_LPSPI3 (IMX95_CCM_NUM_CLK_SRC + 94)
+#define IMX95_CLK_LPSPI4 (IMX95_CCM_NUM_CLK_SRC + 95)
+#define IMX95_CLK_LPSPI5 (IMX95_CCM_NUM_CLK_SRC + 96)
+#define IMX95_CLK_LPSPI6 (IMX95_CCM_NUM_CLK_SRC + 97)
+#define IMX95_CLK_LPSPI7 (IMX95_CCM_NUM_CLK_SRC + 98)
+#define IMX95_CLK_LPSPI8 (IMX95_CCM_NUM_CLK_SRC + 99)
+#define IMX95_CLK_LPTMR2 (IMX95_CCM_NUM_CLK_SRC + 100)
+#define IMX95_CLK_LPUART3 (IMX95_CCM_NUM_CLK_SRC + 101)
+#define IMX95_CLK_LPUART4 (IMX95_CCM_NUM_CLK_SRC + 102)
+#define IMX95_CLK_LPUART5 (IMX95_CCM_NUM_CLK_SRC + 103)
+#define IMX95_CLK_LPUART6 (IMX95_CCM_NUM_CLK_SRC + 104)
+#define IMX95_CLK_LPUART7 (IMX95_CCM_NUM_CLK_SRC + 105)
+#define IMX95_CLK_LPUART8 (IMX95_CCM_NUM_CLK_SRC + 106)
+#define IMX95_CLK_SAI3 (IMX95_CCM_NUM_CLK_SRC + 107)
+#define IMX95_CLK_SAI4 (IMX95_CCM_NUM_CLK_SRC + 108)
+#define IMX95_CLK_SAI5 (IMX95_CCM_NUM_CLK_SRC + 109)
+#define IMX95_CLK_SPDIF (IMX95_CCM_NUM_CLK_SRC + 110)
+#define IMX95_CLK_SWOTRACE (IMX95_CCM_NUM_CLK_SRC + 111)
+#define IMX95_CLK_TPM4 (IMX95_CCM_NUM_CLK_SRC + 112)
+#define IMX95_CLK_TPM5 (IMX95_CCM_NUM_CLK_SRC + 113)
+#define IMX95_CLK_TPM6 (IMX95_CCM_NUM_CLK_SRC + 114)
+#define IMX95_CLK_TSTMR2 (IMX95_CCM_NUM_CLK_SRC + 115)
+#define IMX95_CLK_USBPHYBURUNIN (IMX95_CCM_NUM_CLK_SRC + 116)
+#define IMX95_CLK_USDHC1 (IMX95_CCM_NUM_CLK_SRC + 117)
+#define IMX95_CLK_USDHC2 (IMX95_CCM_NUM_CLK_SRC + 118)
+#define IMX95_CLK_USDHC3 (IMX95_CCM_NUM_CLK_SRC + 119)
+#define IMX95_CLK_V2XPK (IMX95_CCM_NUM_CLK_SRC + 120)
+#define IMX95_CLK_WAKEUPAXI (IMX95_CCM_NUM_CLK_SRC + 121)
+#define IMX95_CLK_XSPISLVROOT (IMX95_CCM_NUM_CLK_SRC + 122)
+#define IMX95_CLK_SEL_EXT (IMX95_CCM_NUM_CLK_SRC + 123 + 0)
+#define IMX95_CLK_SEL_A55C0 (IMX95_CCM_NUM_CLK_SRC + 123 + 1)
+#define IMX95_CLK_SEL_A55C1 (IMX95_CCM_NUM_CLK_SRC + 123 + 2)
+#define IMX95_CLK_SEL_A55C2 (IMX95_CCM_NUM_CLK_SRC + 123 + 3)
+#define IMX95_CLK_SEL_A55C3 (IMX95_CCM_NUM_CLK_SRC + 123 + 4)
+#define IMX95_CLK_SEL_A55C4 (IMX95_CCM_NUM_CLK_SRC + 123 + 5)
+#define IMX95_CLK_SEL_A55C5 (IMX95_CCM_NUM_CLK_SRC + 123 + 6)
+#define IMX95_CLK_SEL_A55P (IMX95_CCM_NUM_CLK_SRC + 123 + 7)
+#define IMX95_CLK_SEL_DRAM (IMX95_CCM_NUM_CLK_SRC + 123 + 8)
+#define IMX95_CLK_SEL_TEMPSENSE (IMX95_CCM_NUM_CLK_SRC + 123 + 9)
+
+#endif /* __DT_BINDINGS_CLOCK_IMX95_H */
diff --git a/arch/arm64/boot/dts/freescale/imx95-power.h b/arch/arm64/boot/dts/freescale/imx95-power.h
new file mode 100644
index 000000000000..a43779317fed
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-power.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Copyright 2024 NXP
+ */
+
+#ifndef __IMX95_POWER_H__
+#define __IMX95_POWER_H__
+
+#define IMX95_PD_ANA 0
+#define IMX95_PD_AON 1
+#define IMX95_PD_BBSM 2
+#define IMX95_PD_CAMERA 3
+#define IMX95_PD_CCMSRCGPC 4
+#define IMX95_PD_A55C0 5
+#define IMX95_PD_A55C1 6
+#define IMX95_PD_A55C2 7
+#define IMX95_PD_A55C3 8
+#define IMX95_PD_A55C4 9
+#define IMX95_PD_A55C5 10
+#define IMX95_PD_A55P 11
+#define IMX95_PD_DDR 12
+#define IMX95_PD_DISPLAY 13
+#define IMX95_PD_GPU 14
+#define IMX95_PD_HSIO_TOP 15
+#define IMX95_PD_HSIO_WAON 16
+#define IMX95_PD_M7 17
+#define IMX95_PD_NETC 18
+#define IMX95_PD_NOC 19
+#define IMX95_PD_NPU 20
+#define IMX95_PD_VPU 21
+#define IMX95_PD_WAKEUP 22
+
+#define IMX95_PERF_ELE 0
+#define IMX95_PERF_M33 1
+#define IMX95_PERF_WAKEUP 2
+#define IMX95_PERF_M7 3
+#define IMX95_PERF_DRAM 4
+#define IMX95_PERF_HSIO 5
+#define IMX95_PERF_NPU 6
+#define IMX95_PERF_NOC 7
+#define IMX95_PERF_A55 8
+#define IMX95_PERF_GPU 9
+#define IMX95_PERF_VPU 10
+#define IMX95_PERF_CAM 11
+#define IMX95_PERF_DISP 12
+#define IMX95_PERF_A55PER 13
+#define IMX95_PERF_A55P 14
+#define IMX95_PERF_A55C0 15
+#define IMX95_PERF_A55C1 16
+#define IMX95_PERF_A55C2 17
+#define IMX95_PERF_A55C3 18
+#define IMX95_PERF_A55C4 19
+#define IMX95_PERF_A55C5 20
+
+#endif
diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
new file mode 100644
index 000000000000..f52023ec7f0c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -0,0 +1,1152 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2024 NXP
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "imx95-clock.h"
+#include "imx95-power.h"
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ idle-states {
+ entry-method = "psci";
+
+ cpu_pd_wait: cpu-pd-wait {
+ compatible = "arm,idle-state";
+ arm,psci-suspend-param = <0x0010033>;
+ local-timer-stop;
+ entry-latency-us = <10000>;
+ exit-latency-us = <7000>;
+ min-residency-us = <27000>;
+ wakeup-latency-us = <15000>;
+ status = "disabled";
+ };
+ };
+
+ A55_0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l0>;
+ };
+
+ A55_1: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x100>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l1>;
+ };
+
+ A55_2: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x200>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l2>;
+ };
+
+ A55_3: cpu@300 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x300>;
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l3>;
+ };
+
+ A55_4: cpu@400 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x400>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l4>;
+ };
+
+ A55_5: cpu@500 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x500>;
+ power-domains = <&scmi_devpd IMX95_PERF_A55>;
+ power-domain-names = "perf";
+ enable-method = "psci";
+ #cooling-cells = <2>;
+ cpu-idle-states = <&cpu_pd_wait>;
+ i-cache-size = <32768>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <128>;
+ d-cache-size = <32768>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <128>;
+ next-level-cache = <&l2_cache_l5>;
+ };
+
+ l2_cache_l0: l2-cache-l0 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l1: l2-cache-l1 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l2: l2-cache-l2 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l3: l2-cache-l3 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l4: l2-cache-l4 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l2_cache_l5: l2-cache-l5 {
+ compatible = "cache";
+ cache-size = <65536>;
+ cache-line-size = <64>;
+ cache-sets = <256>;
+ cache-level = <2>;
+ cache-unified;
+ next-level-cache = <&l3_cache>;
+ };
+
+ l3_cache: l3-cache {
+ compatible = "cache";
+ cache-size = <524288>;
+ cache-line-size = <64>;
+ cache-sets = <1024>;
+ cache-level = <3>;
+ cache-unified;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&A55_0>;
+ };
+
+ core1 {
+ cpu = <&A55_1>;
+ };
+
+ core2 {
+ cpu = <&A55_2>;
+ };
+
+ core3 {
+ cpu = <&A55_3>;
+ };
+
+ core4 {
+ cpu = <&A55_4>;
+ };
+
+ core5 {
+ cpu = <&A55_5>;
+ };
+ };
+ };
+ };
+
+ clk_ext1: clock-ext1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <133000000>;
+ clock-output-names = "clk_ext1";
+ };
+
+ sai1_mclk: sai-mclk1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai1_mclk";
+ };
+
+ sai2_mclk: sai-mclk2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai2_mclk";
+ };
+
+ sai3_mclk: sai-mclk3 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai3_mclk";
+ };
+
+ sai4_mclk: sai-mclk4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai4_mclk";
+ };
+
+ sai5_mclk: sai-mclk5 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency= <0>;
+ clock-output-names = "sai5_mclk";
+ };
+
+ osc_24m: osc-24m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc_24m";
+ };
+
+ sram1: sram@20480000 {
+ compatible = "mmio-sram";
+ reg = <0x0 0x204c0000 0x0 0x18000>;
+ ranges = <0x0 0x0 0x204c0000 0x18000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ firmware {
+ scmi {
+ compatible = "arm,scmi";
+ mboxes = <&mu2 5 0>, <&mu2 3 0>, <&mu2 3 1>;
+ shmem = <&scmi_buf0>, <&scmi_buf1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ scmi_devpd: protocol@11 {
+ reg = <0x11>;
+ #power-domain-cells = <1>;
+ };
+
+ scmi_perf: protocol@13 {
+ reg = <0x13>;
+ #power-domain-cells = <1>;
+ };
+
+ scmi_clk: protocol@14 {
+ reg = <0x14>;
+ #clock-cells = <1>;
+ };
+
+ scmi_sensor: protocol@15 {
+ reg = <0x15>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
+
+ pmu {
+ compatible = "arm,cortex-a55-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ thermal-zones {
+ a55-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <2000>;
+ thermal-sensors = <&scmi_sensor 1>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device =
+ <&A55_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&A55_5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
+ etm0: etm@40840000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0x0 0x40840000 0x0 0x10000>;
+ arm,primecell-periphid = <0xbb95d>;
+ cpu = <&A55_0>;
+ clocks = <&scmi_clk IMX95_CLK_A55PERIPH>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+
+ out-ports {
+ port {
+ etm0_out_port: endpoint {
+ remote-endpoint = <&ca_funnel_in_port0>;
+ };
+ };
+ };
+ };
+
+ funnel0: funnel {
+ /*
+ * non-configurable funnel don't show up on the AMBA
+ * bus. As such no need to add "arm,primecell".
+ */
+ compatible = "arm,coresight-static-funnel";
+ status = "disabled";
+
+ in-ports {
+ port {
+ ca_funnel_in_port0: endpoint {
+ remote-endpoint = <&etm0_out_port>;
+ };
+ };
+ };
+
+ out-ports {
+ port {
+ ca_funnel_out_port0: endpoint {
+ remote-endpoint = <&hugo_funnel_in_port0>;
+ };
+ };
+ };
+ };
+
+ funnel1: funnel_sys {
+ compatible = "arm,coresight-static-funnel";
+ status = "disabled";
+
+ in-ports {
+ port {
+ hugo_funnel_in_port0: endpoint {
+ remote-endpoint = <&ca_funnel_out_port0>;
+ };
+ };
+ };
+
+ out-ports {
+ port {
+ hugo_funnel_out_port0: endpoint {
+ remote-endpoint = <&etf_in_port>;
+ };
+ };
+ };
+ };
+
+ etf: etf@41030000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x0 0x41030000 0x0 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_A55PERIPH>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+
+ in-ports {
+ port {
+ etf_in_port: endpoint {
+ remote-endpoint = <&hugo_funnel_out_port0>;
+ };
+ };
+ };
+
+ out-ports {
+ port {
+ etf_out_port: endpoint {
+ remote-endpoint = <&etr_in_port>;
+ };
+ };
+ };
+ };
+
+ etr: etr@41040000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x0 0x41040000 0x0 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_A55PERIPH>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+
+ in-ports {
+ port {
+ etr_in_port: endpoint {
+ remote-endpoint = <&etf_out_port>;
+ };
+ };
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,no-tick-in-suspend;
+ interrupt-parent = <&gic>;
+ };
+
+ gic: interrupt-controller@48000000 {
+ compatible = "arm,gic-v3";
+ reg = <0 0x48000000 0 0x10000>,
+ <0 0x48060000 0 0xc0000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gic>;
+ dma-noncoherent;
+ ranges;
+
+ its: msi-controller@48040000 {
+ compatible = "arm,gic-v3-its";
+ reg = <0 0x48040000 0 0x20000>;
+ msi-controller;
+ #msi-cells = <1>;
+ dma-noncoherent;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ aips2: bus@42000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x0 0x42000000 0x0 0x800000>;
+ ranges = <0x42000000 0x0 0x42000000 0x8000000>,
+ <0x28000000 0x0 0x28000000 0x10000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mu7: mailbox@42430000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x42430000 0x10000>;
+ interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu8: mailbox@42730000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x42730000 0x10000>;
+ interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ wdog3: watchdog@42490000 {
+ compatible = "fsl,imx93-wdt";
+ reg = <0x42490000 0x10000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ timeout-sec = <40>;
+ fsl,ext-reset-output;
+ status = "disabled";
+ };
+
+ tpm3: pwm@424e0000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x424e0000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm4: pwm@424f0000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x424f0000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM4>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm5: pwm@42500000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x42500000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM5>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm6: pwm@42510000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x42510000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM6>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ lpi2c3: i2c@42530000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x42530000 0x10000>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C3>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c4: i2c@42540000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x42540000 0x10000>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C4>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi3: spi@42550000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42550000 0x10000>;
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI3>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi4: spi@42560000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42560000 0x10000>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI4>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpuart3: serial@42570000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42570000 0x1000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART3>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart4: serial@42580000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42580000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART4>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart5: serial@42590000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42590000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART5>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart6: serial@425a0000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x425a0000 0x1000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART6>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart7: serial@42690000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x42690000 0x1000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART7>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart8: serial@426a0000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x426a0000 0x1000>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART8>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpi2c5: i2c@426b0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426b0000 0x10000>;
+ interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C5>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c6: i2c@426c0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426c0000 0x10000>;
+ interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C6>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c7: i2c@426d0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426d0000 0x10000>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C7>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c8: i2c@426e0000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x426e0000 0x10000>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C8>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi5: spi@426f0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x426f0000 0x10000>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI5>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi6: spi@42700000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42700000 0x10000>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI6>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi7: spi@42710000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42710000 0x10000>;
+ interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI7>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi8: spi@42720000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x42720000 0x10000>;
+ interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI8>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+ };
+
+ aips3: bus@42800000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0 0x42800000 0 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x42800000 0x0 0x42800000 0x800000>;
+
+ usdhc1: mmc@42850000 {
+ compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
+ reg = <0x42850000 0x10000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_WAKEUPAXI>,
+ <&scmi_clk IMX95_CLK_USDHC1>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&scmi_clk IMX95_CLK_USDHC1>;
+ assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ fsl,tuning-start-tap = <1>;
+ fsl,tuning-step= <2>;
+ status = "disabled";
+ };
+
+ usdhc2: mmc@42860000 {
+ compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
+ reg = <0x42860000 0x10000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_WAKEUPAXI>,
+ <&scmi_clk IMX95_CLK_USDHC2>;
+ clock-names = "ipg", "ahb", "per";
+ assigned-clocks = <&scmi_clk IMX95_CLK_USDHC2>;
+ assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
+ assigned-clock-rates = <200000000>;
+ bus-width = <4>;
+ fsl,tuning-start-tap = <1>;
+ fsl,tuning-step= <2>;
+ status = "disabled";
+ };
+
+ usdhc3: mmc@428b0000 {
+ compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
+ reg = <0x428b0000 0x10000>;
+ interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_WAKEUPAXI>,
+ <&scmi_clk IMX95_CLK_USDHC3>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ fsl,tuning-start-tap = <1>;
+ fsl,tuning-step= <2>;
+ status = "disabled";
+ };
+ };
+
+ gpio2: gpio@43810000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43810000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ gpio3: gpio@43820000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43820000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ gpio4: gpio@43840000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43840000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ gpio5: gpio@43850000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x43850000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
+ <&scmi_clk IMX95_CLK_BUSWAKEUP>;
+ clock-names = "gpio", "port";
+ };
+
+ aips1: bus@44000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x0 0x44000000 0x0 0x800000>;
+ ranges = <0x44000000 0x0 0x44000000 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mu1: mailbox@44220000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x44220000 0x10000>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu2: mailbox@445b0000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x445b0000 0x1000>;
+ ranges;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #mbox-cells = <2>;
+
+ sram0: sram@445b1000 {
+ compatible = "mmio-sram";
+ reg = <0x445b1000 0x400>;
+ ranges = <0x0 0x445b1000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ scmi_buf0: scmi-sram-section@0 {
+ compatible = "arm,scmi-shmem";
+ reg = <0x0 0x80>;
+ };
+
+ scmi_buf1: scmi-sram-section@80 {
+ compatible = "arm,scmi-shmem";
+ reg = <0x80 0x80>;
+ };
+ };
+
+ };
+
+ mu3: mailbox@445d0000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x445d0000 0x10000>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu4: mailbox@445f0000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x445f0000 0x10000>;
+ interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ mu6: mailbox@44630000 {
+ compatible = "fsl,imx95-mu";
+ reg = <0x44630000 0x10000>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ tpm1: pwm@44310000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x44310000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_BUSAON>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ tpm2: pwm@44320000 {
+ compatible = "fsl,imx7ulp-pwm";
+ reg = <0x44320000 0x1000>;
+ clocks = <&scmi_clk IMX95_CLK_TPM2>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ lpi2c1: i2c@44340000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x44340000 0x10000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C1>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpi2c2: i2c@44350000 {
+ compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
+ reg = <0x44350000 0x10000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPI2C2>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi1: spi@44360000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x44360000 0x10000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpspi2: spi@44370000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
+ reg = <0x44370000 0x10000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
+ <&scmi_clk IMX95_CLK_BUSAON>;
+ clock-names = "per", "ipg";
+ status = "disabled";
+ };
+
+ lpuart1: serial@44380000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x44380000 0x1000>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart2: serial@44390000 {
+ compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
+ "fsl,imx7ulp-lpuart";
+ reg = <0x44390000 0x1000>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_LPUART2>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ adc1: adc@44530000 {
+ compatible = "nxp,imx93-adc";
+ reg = <0x44530000 0x10000>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&scmi_clk IMX95_CLK_ADC>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ };
+
+ aips4: bus@49000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ reg = <0x0 0x49000000 0x0 0x800000>;
+ ranges = <0x49000000 0x0 0x49000000 0x800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ smmu: iommu@490d0000 {
+ compatible = "arm,smmu-v3";
+ reg = <0x490d0000 0x100000>;
+ interrupts = <GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 334 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 326 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "eventq", "gerror", "priq", "cmdq-sync";
+ #iommu-cells = <1>;
+ status = "disabled";
+ };
+ };
+
+ gpio1: gpio@47400000 {
+ compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
+ reg = <0x0 0x47400000 0x0 0x1000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&scmi_clk IMX95_CLK_M33>,
+ <&scmi_clk IMX95_CLK_M33>;
+ clock-names = "gpio", "port";
+ status = "disabled";
+ };
+
+ elemu0: mailbox@47520000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47520000 0x0 0x10000>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu1: mailbox@47530000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47530000 0x0 0x10000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu2: mailbox@47540000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47540000 0x0 0x10000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu3: mailbox@47550000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47550000 0x0 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ };
+
+ elemu4: mailbox@47560000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47560000 0x0 0x10000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ elemu5: mailbox@47570000 {
+ compatible = "fsl,imx95-mu-ele";
+ reg = <0x0 0x47570000 0x0 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ status = "disabled";
+ };
+
+ v2x_mu: mailbox@47350000 {
+ compatible = "fsl,imx95-mu-v2x";
+ reg = <0x0 0x47350000 0x0 0x10000>;
+ interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ };
+
+ v2x_mu6: mailbox@47320000 {
+ compatible = "fsl,imx95-mu-v2x";
+ reg = <0x0 0x47320000 0x0 0x10000>;
+ interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <2>;
+ };
+ };
+};
--
2.37.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 3/3] arm64: dts: freescale: add i.MX95 19x19 EVK minimal board dts
2024-04-28 12:22 ` Peng Fan (OSS)
@ 2024-04-28 12:22 ` Peng Fan (OSS)
-1 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan
From: Peng Fan <peng.fan@nxp.com>
Add a minimal dts for i.MX95 19x19 EVK board:
- lpuart1 as console
- sdhc1/2 as storage
As of now, because scmi pinctrl support not ready, so count on
bootloader to set the pinctrl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 111 ++++++++++++++++++++++
2 files changed, 112 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index bd443c2bc5a4..057e23fde780 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -236,6 +236,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxca.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-var-som-symphony.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk.dtb
imx8mm-venice-gw72xx-0x-imx219-dtbs := imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-imx219.dtbo
imx8mm-venice-gw72xx-0x-rpidsi-dtbs := imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rpidsi.dtbo
diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
new file mode 100644
index 000000000000..4ca63ea1e787
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2024 NXP
+ */
+
+/dts-v1/;
+
+#include "imx95.dtsi"
+
+/ {
+ model = "NXP i.MX95 19X19 board";
+ compatible = "fsl,imx95-19x19-evk", "fsl,imx95";
+
+ aliases {
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ i2c0 = &lpi2c1;
+ i2c1 = &lpi2c2;
+ i2c2 = &lpi2c3;
+ i2c3 = &lpi2c4;
+ i2c4 = &lpi2c5;
+ i2c5 = &lpi2c6;
+ i2c6 = &lpi2c7;
+ i2c7 = &lpi2c8;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ serial0 = &lpuart1;
+ serial1 = &lpuart2;
+ serial2 = &lpuart3;
+ serial3 = &lpuart4;
+ serial4 = &lpuart5;
+ serial5 = &lpuart6;
+ serial6 = &lpuart7;
+ serial7 = &lpuart8;
+ };
+
+ chosen {
+ stdout-path = &lpuart1;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ linux_cma: linux,cma {
+ compatible = "shared-dma-pool";
+ alloc-ranges = <0 0x80000000 0 0x7F000000>;
+ size = <0 0x3c000000>;
+ linux,cma-default;
+ reusable;
+ };
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "+V1.8_SW";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "+V3.3_SW";
+ };
+
+ reg_vref_1v8: regulator-adc-vref {
+ compatible = "regulator-fixed";
+ regulator-name = "vref_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&lpuart1 {
+ /* console */
+ status = "okay";
+};
+
+&mu7 {
+ status = "okay";
+};
+
+&usdhc1 {
+ bus-width = <8>;
+ non-removable;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
+
+&usdhc2 {
+ non-removable;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&wdog3 {
+ status = "okay";
+};
--
2.37.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH v3 3/3] arm64: dts: freescale: add i.MX95 19x19 EVK minimal board dts
@ 2024-04-28 12:22 ` Peng Fan (OSS)
0 siblings, 0 replies; 12+ messages in thread
From: Peng Fan (OSS) @ 2024-04-28 12:22 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan
From: Peng Fan <peng.fan@nxp.com>
Add a minimal dts for i.MX95 19x19 EVK board:
- lpuart1 as console
- sdhc1/2 as storage
As of now, because scmi pinctrl support not ready, so count on
bootloader to set the pinctrl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 111 ++++++++++++++++++++++
2 files changed, 112 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index bd443c2bc5a4..057e23fde780 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -236,6 +236,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxca.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
dtb-$(CONFIG_ARCH_MXC) += imx93-var-som-symphony.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk.dtb
imx8mm-venice-gw72xx-0x-imx219-dtbs := imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-imx219.dtbo
imx8mm-venice-gw72xx-0x-rpidsi-dtbs := imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rpidsi.dtbo
diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
new file mode 100644
index 000000000000..4ca63ea1e787
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2024 NXP
+ */
+
+/dts-v1/;
+
+#include "imx95.dtsi"
+
+/ {
+ model = "NXP i.MX95 19X19 board";
+ compatible = "fsl,imx95-19x19-evk", "fsl,imx95";
+
+ aliases {
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ i2c0 = &lpi2c1;
+ i2c1 = &lpi2c2;
+ i2c2 = &lpi2c3;
+ i2c3 = &lpi2c4;
+ i2c4 = &lpi2c5;
+ i2c5 = &lpi2c6;
+ i2c6 = &lpi2c7;
+ i2c7 = &lpi2c8;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ serial0 = &lpuart1;
+ serial1 = &lpuart2;
+ serial2 = &lpuart3;
+ serial3 = &lpuart4;
+ serial4 = &lpuart5;
+ serial5 = &lpuart6;
+ serial6 = &lpuart7;
+ serial7 = &lpuart8;
+ };
+
+ chosen {
+ stdout-path = &lpuart1;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ linux_cma: linux,cma {
+ compatible = "shared-dma-pool";
+ alloc-ranges = <0 0x80000000 0 0x7F000000>;
+ size = <0 0x3c000000>;
+ linux,cma-default;
+ reusable;
+ };
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "+V1.8_SW";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "+V3.3_SW";
+ };
+
+ reg_vref_1v8: regulator-adc-vref {
+ compatible = "regulator-fixed";
+ regulator-name = "vref_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&lpuart1 {
+ /* console */
+ status = "okay";
+};
+
+&mu7 {
+ status = "okay";
+};
+
+&usdhc1 {
+ bus-width = <8>;
+ non-removable;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
+
+&usdhc2 {
+ non-removable;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&wdog3 {
+ status = "okay";
+};
--
2.37.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
2024-04-28 12:22 ` Peng Fan (OSS)
@ 2024-04-29 7:57 ` Alexander Stein
-1 siblings, 0 replies; 12+ messages in thread
From: Alexander Stein @ 2024-04-29 7:57 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan,
Peng Fan (OSS)
Hi Peng,
thanks for your patch.
Am Sonntag, 28. April 2024, 14:22:20 CEST schrieb Peng Fan (OSS):
> From: Peng Fan <peng.fan@nxp.com>
>
> i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
> and Edgelock secure enclave security. This patch is to add a minimal
> dtsi, with cpu cores, coresight, scmi, gic, uart, mu, sdhc, lpi2c added.
>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/imx95-clock.h | 187 +++++
> arch/arm64/boot/dts/freescale/imx95-power.h | 55 ++
> arch/arm64/boot/dts/freescale/imx95.dtsi | 1152 +++++++++++++++++++++++++++
> 3 files changed, 1394 insertions(+)
>
> [snip]
> diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
> new file mode 100644
> index 000000000000..f52023ec7f0c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
> [snip]
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + aips2: bus@42000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0x0 0x42000000 0x0 0x800000>;
> + ranges = <0x42000000 0x0 0x42000000 0x8000000>,
> + <0x28000000 0x0 0x28000000 0x10000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + mu7: mailbox@42430000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x42430000 0x10000>;
> + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu8: mailbox@42730000 {
Please sort all nodes by address.
> + compatible = "fsl,imx95-mu";
> + reg = <0x42730000 0x10000>;
> + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + wdog3: watchdog@42490000 {
> + compatible = "fsl,imx93-wdt";
> + reg = <0x42490000 0x10000>;
> + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + timeout-sec = <40>;
> + fsl,ext-reset-output;
Isn't this board specific?
> + status = "disabled";
> + };
> +
> + tpm3: pwm@424e0000 {
> + compatible = "fsl,imx7ulp-pwm";
> + reg = <0x424e0000 0x1000>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> [snip]
> + };
> +
> + aips3: bus@42800000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0 0x42800000 0 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x42800000 0x0 0x42800000 0x800000>;
> +
> + usdhc1: mmc@42850000 {
> + compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
> + reg = <0x42850000 0x10000>;
> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_WAKEUPAXI>,
> + <&scmi_clk IMX95_CLK_USDHC1>;
> + clock-names = "ipg", "ahb", "per";
> + assigned-clocks = <&scmi_clk IMX95_CLK_USDHC1>;
> + assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
> + assigned-clock-rates = <400000000>;
> + bus-width = <8>;
> + fsl,tuning-start-tap = <1>;
> + fsl,tuning-step= <2>;
Isn't this board specific? Or is there a hardware limitation?
> + status = "disabled";
> + };
> +
> + usdhc2: mmc@42860000 {
> + compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
> + reg = <0x42860000 0x10000>;
> + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_WAKEUPAXI>,
> + <&scmi_clk IMX95_CLK_USDHC2>;
> + clock-names = "ipg", "ahb", "per";
> + assigned-clocks = <&scmi_clk IMX95_CLK_USDHC2>;
> + assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
> + assigned-clock-rates = <200000000>;
Why is usdhc2 only 200 MHz but usdhc1 400 MHz?
> + bus-width = <4>;
> + fsl,tuning-start-tap = <1>;
> + fsl,tuning-step= <2>;
Isn't this board specific? Or is there a hardware limitation?
> + status = "disabled";
> + };
> +
> + usdhc3: mmc@428b0000 {
> + compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
> + reg = <0x428b0000 0x10000>;
> + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_WAKEUPAXI>,
> + <&scmi_clk IMX95_CLK_USDHC3>;
> + clock-names = "ipg", "ahb", "per";
No need to configure IMX95_CLK_USDHC3?
> + bus-width = <4>;
> + fsl,tuning-start-tap = <1>;
> + fsl,tuning-step= <2>;
> + status = "disabled";
> + };
> + };
> +
> + gpio2: gpio@43810000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43810000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + gpio3: gpio@43820000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43820000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + gpio4: gpio@43840000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43840000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + gpio5: gpio@43850000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43850000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + aips1: bus@44000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0x0 0x44000000 0x0 0x800000>;
> + ranges = <0x44000000 0x0 0x44000000 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + mu1: mailbox@44220000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x44220000 0x10000>;
> + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu2: mailbox@445b0000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x445b0000 0x1000>;
> + ranges;
> + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #mbox-cells = <2>;
> +
> + sram0: sram@445b1000 {
> + compatible = "mmio-sram";
> + reg = <0x445b1000 0x400>;
> + ranges = <0x0 0x445b1000 0x400>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + scmi_buf0: scmi-sram-section@0 {
> + compatible = "arm,scmi-shmem";
> + reg = <0x0 0x80>;
> + };
> +
> + scmi_buf1: scmi-sram-section@80 {
> + compatible = "arm,scmi-shmem";
> + reg = <0x80 0x80>;
> + };
> + };
I guess this MU depends on the system manager firmware, no?
> + };
> +
> + mu3: mailbox@445d0000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x445d0000 0x10000>;
> + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu4: mailbox@445f0000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x445f0000 0x10000>;
> + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu6: mailbox@44630000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x44630000 0x10000>;
> + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + tpm1: pwm@44310000 {
> + compatible = "fsl,imx7ulp-pwm";
> + reg = <0x44310000 0x1000>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + tpm2: pwm@44320000 {
> + compatible = "fsl,imx7ulp-pwm";
> + reg = <0x44320000 0x1000>;
> + clocks = <&scmi_clk IMX95_CLK_TPM2>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + lpi2c1: i2c@44340000 {
> + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
> + reg = <0x44340000 0x10000>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPI2C1>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpi2c2: i2c@44350000 {
> + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
> + reg = <0x44350000 0x10000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPI2C2>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpspi1: spi@44360000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
> + reg = <0x44360000 0x10000>;
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpspi2: spi@44370000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
> + reg = <0x44370000 0x10000>;
> + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpuart1: serial@44380000 {
> + compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
> + "fsl,imx7ulp-lpuart";
> + reg = <0x44380000 0x1000>;
> + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPUART1>;
> + clock-names = "ipg";
> + status = "disabled";
> + };
> +
> + lpuart2: serial@44390000 {
> + compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
> + "fsl,imx7ulp-lpuart";
> + reg = <0x44390000 0x1000>;
> + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPUART2>;
> + clock-names = "ipg";
> + status = "disabled";
> + };
> +
> + adc1: adc@44530000 {
> + compatible = "nxp,imx93-adc";
> + reg = <0x44530000 0x10000>;
> + interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_ADC>;
> + clock-names = "ipg";
> + status = "disabled";
> + };
Please sort the nodes by address.
> + };
> +
> + aips4: bus@49000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0x0 0x49000000 0x0 0x800000>;
> + ranges = <0x49000000 0x0 0x49000000 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + smmu: iommu@490d0000 {
> + compatible = "arm,smmu-v3";
> + reg = <0x490d0000 0x100000>;
> + interrupts = <GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 334 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 326 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "eventq", "gerror", "priq", "cmdq-sync";
> + #iommu-cells = <1>;
> + status = "disabled";
> + };
> + };
> +
> + gpio1: gpio@47400000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x47400000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_M33>,
> + <&scmi_clk IMX95_CLK_M33>;
> + clock-names = "gpio", "port";
> + status = "disabled";
I'm wondering of there should be a comment here that gpio1 usually is under
exclusive control of SM.
> + };
> +
> + elemu0: mailbox@47520000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47520000 0x0 0x10000>;
> + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu1: mailbox@47530000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47530000 0x0 0x10000>;
> + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu2: mailbox@47540000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47540000 0x0 0x10000>;
> + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu3: mailbox@47550000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47550000 0x0 0x10000>;
> + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + };
> +
> + elemu4: mailbox@47560000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47560000 0x0 0x10000>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu5: mailbox@47570000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47570000 0x0 0x10000>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + v2x_mu: mailbox@47350000 {
> + compatible = "fsl,imx95-mu-v2x";
> + reg = <0x0 0x47350000 0x0 0x10000>;
> + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + };
> +
> + v2x_mu6: mailbox@47320000 {
> + compatible = "fsl,imx95-mu-v2x";
> + reg = <0x0 0x47320000 0x0 0x10000>;
> + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + };
Please sort nodes by address.
Best regards,
Alexander
> + };
> +};
>
>
--
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
@ 2024-04-29 7:57 ` Alexander Stein
0 siblings, 0 replies; 12+ messages in thread
From: Alexander Stein @ 2024-04-29 7:57 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan,
Peng Fan (OSS)
Hi Peng,
thanks for your patch.
Am Sonntag, 28. April 2024, 14:22:20 CEST schrieb Peng Fan (OSS):
> From: Peng Fan <peng.fan@nxp.com>
>
> i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
> and Edgelock secure enclave security. This patch is to add a minimal
> dtsi, with cpu cores, coresight, scmi, gic, uart, mu, sdhc, lpi2c added.
>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/imx95-clock.h | 187 +++++
> arch/arm64/boot/dts/freescale/imx95-power.h | 55 ++
> arch/arm64/boot/dts/freescale/imx95.dtsi | 1152 +++++++++++++++++++++++++++
> 3 files changed, 1394 insertions(+)
>
> [snip]
> diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
> new file mode 100644
> index 000000000000..f52023ec7f0c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
> [snip]
> + soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + aips2: bus@42000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0x0 0x42000000 0x0 0x800000>;
> + ranges = <0x42000000 0x0 0x42000000 0x8000000>,
> + <0x28000000 0x0 0x28000000 0x10000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + mu7: mailbox@42430000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x42430000 0x10000>;
> + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu8: mailbox@42730000 {
Please sort all nodes by address.
> + compatible = "fsl,imx95-mu";
> + reg = <0x42730000 0x10000>;
> + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + wdog3: watchdog@42490000 {
> + compatible = "fsl,imx93-wdt";
> + reg = <0x42490000 0x10000>;
> + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + timeout-sec = <40>;
> + fsl,ext-reset-output;
Isn't this board specific?
> + status = "disabled";
> + };
> +
> + tpm3: pwm@424e0000 {
> + compatible = "fsl,imx7ulp-pwm";
> + reg = <0x424e0000 0x1000>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> [snip]
> + };
> +
> + aips3: bus@42800000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0 0x42800000 0 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x42800000 0x0 0x42800000 0x800000>;
> +
> + usdhc1: mmc@42850000 {
> + compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
> + reg = <0x42850000 0x10000>;
> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_WAKEUPAXI>,
> + <&scmi_clk IMX95_CLK_USDHC1>;
> + clock-names = "ipg", "ahb", "per";
> + assigned-clocks = <&scmi_clk IMX95_CLK_USDHC1>;
> + assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
> + assigned-clock-rates = <400000000>;
> + bus-width = <8>;
> + fsl,tuning-start-tap = <1>;
> + fsl,tuning-step= <2>;
Isn't this board specific? Or is there a hardware limitation?
> + status = "disabled";
> + };
> +
> + usdhc2: mmc@42860000 {
> + compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
> + reg = <0x42860000 0x10000>;
> + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_WAKEUPAXI>,
> + <&scmi_clk IMX95_CLK_USDHC2>;
> + clock-names = "ipg", "ahb", "per";
> + assigned-clocks = <&scmi_clk IMX95_CLK_USDHC2>;
> + assigned-clock-parents = <&scmi_clk IMX95_CLK_SYSPLL1_PFD1>;
> + assigned-clock-rates = <200000000>;
Why is usdhc2 only 200 MHz but usdhc1 400 MHz?
> + bus-width = <4>;
> + fsl,tuning-start-tap = <1>;
> + fsl,tuning-step= <2>;
Isn't this board specific? Or is there a hardware limitation?
> + status = "disabled";
> + };
> +
> + usdhc3: mmc@428b0000 {
> + compatible = "fsl,imx95-usdhc", "fsl,imx8mm-usdhc";
> + reg = <0x428b0000 0x10000>;
> + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_WAKEUPAXI>,
> + <&scmi_clk IMX95_CLK_USDHC3>;
> + clock-names = "ipg", "ahb", "per";
No need to configure IMX95_CLK_USDHC3?
> + bus-width = <4>;
> + fsl,tuning-start-tap = <1>;
> + fsl,tuning-step= <2>;
> + status = "disabled";
> + };
> + };
> +
> + gpio2: gpio@43810000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43810000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + gpio3: gpio@43820000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43820000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + gpio4: gpio@43840000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43840000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + gpio5: gpio@43850000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x43850000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> + clock-names = "gpio", "port";
> + };
> +
> + aips1: bus@44000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0x0 0x44000000 0x0 0x800000>;
> + ranges = <0x44000000 0x0 0x44000000 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + mu1: mailbox@44220000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x44220000 0x10000>;
> + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu2: mailbox@445b0000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x445b0000 0x1000>;
> + ranges;
> + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #mbox-cells = <2>;
> +
> + sram0: sram@445b1000 {
> + compatible = "mmio-sram";
> + reg = <0x445b1000 0x400>;
> + ranges = <0x0 0x445b1000 0x400>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + scmi_buf0: scmi-sram-section@0 {
> + compatible = "arm,scmi-shmem";
> + reg = <0x0 0x80>;
> + };
> +
> + scmi_buf1: scmi-sram-section@80 {
> + compatible = "arm,scmi-shmem";
> + reg = <0x80 0x80>;
> + };
> + };
I guess this MU depends on the system manager firmware, no?
> + };
> +
> + mu3: mailbox@445d0000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x445d0000 0x10000>;
> + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu4: mailbox@445f0000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x445f0000 0x10000>;
> + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + mu6: mailbox@44630000 {
> + compatible = "fsl,imx95-mu";
> + reg = <0x44630000 0x10000>;
> + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + tpm1: pwm@44310000 {
> + compatible = "fsl,imx7ulp-pwm";
> + reg = <0x44310000 0x1000>;
> + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + tpm2: pwm@44320000 {
> + compatible = "fsl,imx7ulp-pwm";
> + reg = <0x44320000 0x1000>;
> + clocks = <&scmi_clk IMX95_CLK_TPM2>;
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + lpi2c1: i2c@44340000 {
> + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
> + reg = <0x44340000 0x10000>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPI2C1>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpi2c2: i2c@44350000 {
> + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-lpi2c";
> + reg = <0x44350000 0x10000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPI2C2>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpspi1: spi@44360000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
> + reg = <0x44360000 0x10000>;
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpspi2: spi@44370000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,imx95-spi", "fsl,imx7ulp-spi";
> + reg = <0x44370000 0x10000>;
> + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
> + <&scmi_clk IMX95_CLK_BUSAON>;
> + clock-names = "per", "ipg";
> + status = "disabled";
> + };
> +
> + lpuart1: serial@44380000 {
> + compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
> + "fsl,imx7ulp-lpuart";
> + reg = <0x44380000 0x1000>;
> + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPUART1>;
> + clock-names = "ipg";
> + status = "disabled";
> + };
> +
> + lpuart2: serial@44390000 {
> + compatible = "fsl,imx95-lpuart", "fsl,imx8ulp-lpuart",
> + "fsl,imx7ulp-lpuart";
> + reg = <0x44390000 0x1000>;
> + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_LPUART2>;
> + clock-names = "ipg";
> + status = "disabled";
> + };
> +
> + adc1: adc@44530000 {
> + compatible = "nxp,imx93-adc";
> + reg = <0x44530000 0x10000>;
> + interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX95_CLK_ADC>;
> + clock-names = "ipg";
> + status = "disabled";
> + };
Please sort the nodes by address.
> + };
> +
> + aips4: bus@49000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0x0 0x49000000 0x0 0x800000>;
> + ranges = <0x49000000 0x0 0x49000000 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + smmu: iommu@490d0000 {
> + compatible = "arm,smmu-v3";
> + reg = <0x490d0000 0x100000>;
> + interrupts = <GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 334 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 326 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "eventq", "gerror", "priq", "cmdq-sync";
> + #iommu-cells = <1>;
> + status = "disabled";
> + };
> + };
> +
> + gpio1: gpio@47400000 {
> + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> + reg = <0x0 0x47400000 0x0 0x1000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&scmi_clk IMX95_CLK_M33>,
> + <&scmi_clk IMX95_CLK_M33>;
> + clock-names = "gpio", "port";
> + status = "disabled";
I'm wondering of there should be a comment here that gpio1 usually is under
exclusive control of SM.
> + };
> +
> + elemu0: mailbox@47520000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47520000 0x0 0x10000>;
> + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu1: mailbox@47530000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47530000 0x0 0x10000>;
> + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu2: mailbox@47540000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47540000 0x0 0x10000>;
> + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu3: mailbox@47550000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47550000 0x0 0x10000>;
> + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + };
> +
> + elemu4: mailbox@47560000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47560000 0x0 0x10000>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + elemu5: mailbox@47570000 {
> + compatible = "fsl,imx95-mu-ele";
> + reg = <0x0 0x47570000 0x0 0x10000>;
> + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + status = "disabled";
> + };
> +
> + v2x_mu: mailbox@47350000 {
> + compatible = "fsl,imx95-mu-v2x";
> + reg = <0x0 0x47350000 0x0 0x10000>;
> + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + };
> +
> + v2x_mu6: mailbox@47320000 {
> + compatible = "fsl,imx95-mu-v2x";
> + reg = <0x0 0x47320000 0x0 0x10000>;
> + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
> + #mbox-cells = <2>;
> + };
Please sort nodes by address.
Best regards,
Alexander
> + };
> +};
>
>
--
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
2024-04-29 7:57 ` Alexander Stein
@ 2024-05-03 0:15 ` Peng Fan
-1 siblings, 0 replies; 12+ messages in thread
From: Peng Fan @ 2024-05-03 0:15 UTC (permalink / raw)
To: Alexander Stein, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan (OSS)
> Subject: Re: [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
>
> Hi Peng,
>
> thanks for your patch.
>
> Am Sonntag, 28. April 2024, 14:22:20 CEST schrieb Peng Fan (OSS):
> > From: Peng Fan <peng.fan@nxp.com>
> >
> > i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
> > and Edgelock secure enclave security. This patch is to add a minimal
> > dtsi, with cpu cores, coresight, scmi, gic, uart, mu, sdhc, lpi2c added.
> >
> > Signed-off-by: Peng Fan <peng.fan@nxp.com>
> > ---
> > arch/arm64/boot/dts/freescale/imx95-clock.h | 187 +++++
> > arch/arm64/boot/dts/freescale/imx95-power.h | 55 ++
> > arch/arm64/boot/dts/freescale/imx95.dtsi | 1152
> +++++++++++++++++++++++++++
> > 3 files changed, 1394 insertions(+)
> >
> > [snip]
> > diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi
> > b/arch/arm64/boot/dts/freescale/imx95.dtsi
> > new file mode 100644
> > index 000000000000..f52023ec7f0c
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
> > [snip]
> > + soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + aips2: bus@42000000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0x0 0x42000000 0x0 0x800000>;
> > + ranges = <0x42000000 0x0 0x42000000
> 0x8000000>,
> > + <0x28000000 0x0 0x28000000
> 0x10000000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + mu7: mailbox@42430000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x42430000 0x10000>;
> > + interrupts = <GIC_SPI 234
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu8: mailbox@42730000 {
>
> Please sort all nodes by address.
Sure. fix in v4.
>
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x42730000 0x10000>;
> > + interrupts = <GIC_SPI 235
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + wdog3: watchdog@42490000 {
> > + compatible = "fsl,imx93-wdt";
> > + reg = <0x42490000 0x10000>;
> > + interrupts = <GIC_SPI 77
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + timeout-sec = <40>;
> > + fsl,ext-reset-output;
>
> Isn't this board specific?
Yeah. Board specific, remove it.
>
> > + status = "disabled";
> > + };
> > +
> > + tpm3: pwm@424e0000 {
> > + compatible = "fsl,imx7ulp-pwm";
> > + reg = <0x424e0000 0x1000>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + #pwm-cells = <3>;
> > + status = "disabled";
> > + };
> > [snip]
> > + };
> > +
> > + aips3: bus@42800000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0 0x42800000 0 0x800000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0x42800000 0x0 0x42800000 0x800000>;
> > +
> > + usdhc1: mmc@42850000 {
> > + compatible = "fsl,imx95-usdhc",
> "fsl,imx8mm-usdhc";
> > + reg = <0x42850000 0x10000>;
> > + interrupts = <GIC_SPI 86
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk
> IMX95_CLK_WAKEUPAXI>,
> > + <&scmi_clk IMX95_CLK_USDHC1>;
> > + clock-names = "ipg", "ahb", "per";
> > + assigned-clocks = <&scmi_clk
> IMX95_CLK_USDHC1>;
> > + assigned-clock-parents = <&scmi_clk
> IMX95_CLK_SYSPLL1_PFD1>;
> > + assigned-clock-rates = <400000000>;
> > + bus-width = <8>;
> > + fsl,tuning-start-tap = <1>;
> > + fsl,tuning-step= <2>;
>
> Isn't this board specific? Or is there a hardware limitation?
Yeah, just follow what imx93 has, board could override them.
No hardware limitation as I know.
>
> > + status = "disabled";
> > + };
> > +
> > + usdhc2: mmc@42860000 {
> > + compatible = "fsl,imx95-usdhc",
> "fsl,imx8mm-usdhc";
> > + reg = <0x42860000 0x10000>;
> > + interrupts = <GIC_SPI 87
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk
> IMX95_CLK_WAKEUPAXI>,
> > + <&scmi_clk IMX95_CLK_USDHC2>;
> > + clock-names = "ipg", "ahb", "per";
> > + assigned-clocks = <&scmi_clk
> IMX95_CLK_USDHC2>;
> > + assigned-clock-parents = <&scmi_clk
> IMX95_CLK_SYSPLL1_PFD1>;
> > + assigned-clock-rates = <200000000>;
>
> Why is usdhc2 only 200 MHz but usdhc1 400 MHz?
No specific reason, 400M should also work.
>
> > + bus-width = <4>;
> > + fsl,tuning-start-tap = <1>;
> > + fsl,tuning-step= <2>;
>
> Isn't this board specific? Or is there a hardware limitation?
Yes, just follow what i.MX93 has and board could override them.
>
> > + status = "disabled";
> > + };
> > +
> > + usdhc3: mmc@428b0000 {
> > + compatible = "fsl,imx95-usdhc",
> "fsl,imx8mm-usdhc";
> > + reg = <0x428b0000 0x10000>;
> > + interrupts = <GIC_SPI 191
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk
> IMX95_CLK_WAKEUPAXI>,
> > + <&scmi_clk IMX95_CLK_USDHC3>;
> > + clock-names = "ipg", "ahb", "per";
>
> No need to configure IMX95_CLK_USDHC3?
I will add it.
>
> > + bus-width = <4>;
> > + fsl,tuning-start-tap = <1>;
> > + fsl,tuning-step= <2>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + gpio2: gpio@43810000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43810000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + gpio3: gpio@43820000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43820000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + gpio4: gpio@43840000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43840000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + gpio5: gpio@43850000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43850000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + aips1: bus@44000000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0x0 0x44000000 0x0 0x800000>;
> > + ranges = <0x44000000 0x0 0x44000000 0x800000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + mu1: mailbox@44220000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x44220000 0x10000>;
> > + interrupts = <GIC_SPI 224
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu2: mailbox@445b0000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x445b0000 0x1000>;
> > + ranges;
> > + interrupts = <GIC_SPI 226
> IRQ_TYPE_LEVEL_HIGH>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + #mbox-cells = <2>;
> > +
> > + sram0: sram@445b1000 {
> > + compatible = "mmio-sram";
> > + reg = <0x445b1000 0x400>;
> > + ranges = <0x0 0x445b1000 0x400>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + scmi_buf0: scmi-sram-section@0 {
> > + compatible = "arm,scmi-
> shmem";
> > + reg = <0x0 0x80>;
> > + };
> > +
> > + scmi_buf1: scmi-sram-section@80
> {
> > + compatible = "arm,scmi-
> shmem";
> > + reg = <0x80 0x80>;
> > + };
> > + };
>
> I guess this MU depends on the system manager firmware, no?
Yes, depends on firmware.
>
> > + };
> > +
> > + mu3: mailbox@445d0000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x445d0000 0x10000>;
> > + interrupts = <GIC_SPI 228
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu4: mailbox@445f0000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x445f0000 0x10000>;
> > + interrupts = <GIC_SPI 230
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu6: mailbox@44630000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x44630000 0x10000>;
> > + interrupts = <GIC_SPI 206
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + tpm1: pwm@44310000 {
> > + compatible = "fsl,imx7ulp-pwm";
> > + reg = <0x44310000 0x1000>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #pwm-cells = <3>;
> > + status = "disabled";
> > + };
> > +
> > + tpm2: pwm@44320000 {
> > + compatible = "fsl,imx7ulp-pwm";
> > + reg = <0x44320000 0x1000>;
> > + clocks = <&scmi_clk IMX95_CLK_TPM2>;
> > + #pwm-cells = <3>;
> > + status = "disabled";
> > + };
> > +
> > + lpi2c1: i2c@44340000 {
> > + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-
> lpi2c";
> > + reg = <0x44340000 0x10000>;
> > + interrupts = <GIC_SPI 13
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPI2C1>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpi2c2: i2c@44350000 {
> > + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-
> lpi2c";
> > + reg = <0x44350000 0x10000>;
> > + interrupts = <GIC_SPI 14
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPI2C2>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpspi1: spi@44360000 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "fsl,imx95-spi", "fsl,imx7ulp-
> spi";
> > + reg = <0x44360000 0x10000>;
> > + interrupts = <GIC_SPI 16
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpspi2: spi@44370000 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "fsl,imx95-spi", "fsl,imx7ulp-
> spi";
> > + reg = <0x44370000 0x10000>;
> > + interrupts = <GIC_SPI 17
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpuart1: serial@44380000 {
> > + compatible = "fsl,imx95-lpuart",
> "fsl,imx8ulp-lpuart",
> > + "fsl,imx7ulp-lpuart";
> > + reg = <0x44380000 0x1000>;
> > + interrupts = <GIC_SPI 19
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPUART1>;
> > + clock-names = "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpuart2: serial@44390000 {
> > + compatible = "fsl,imx95-lpuart",
> "fsl,imx8ulp-lpuart",
> > + "fsl,imx7ulp-lpuart";
> > + reg = <0x44390000 0x1000>;
> > + interrupts = <GIC_SPI 20
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPUART2>;
> > + clock-names = "ipg";
> > + status = "disabled";
> > + };
> > +
> > + adc1: adc@44530000 {
> > + compatible = "nxp,imx93-adc";
> > + reg = <0x44530000 0x10000>;
> > + interrupts = <GIC_SPI 199
> IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 200
> IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 201
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_ADC>;
> > + clock-names = "ipg";
> > + status = "disabled";
> > + };
>
> Please sort the nodes by address.
Sure.
>
> > + };
> > +
> > + aips4: bus@49000000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0x0 0x49000000 0x0 0x800000>;
> > + ranges = <0x49000000 0x0 0x49000000 0x800000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + smmu: iommu@490d0000 {
> > + compatible = "arm,smmu-v3";
> > + reg = <0x490d0000 0x100000>;
> > + interrupts = <GIC_SPI 325
> IRQ_TYPE_EDGE_RISING>,
> > + <GIC_SPI 328
> IRQ_TYPE_EDGE_RISING>,
> > + <GIC_SPI 334
> IRQ_TYPE_EDGE_RISING>,
> > + <GIC_SPI 326
> IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "eventq", "gerror", "priq",
> "cmdq-sync";
> > + #iommu-cells = <1>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + gpio1: gpio@47400000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x47400000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_M33>,
> > + <&scmi_clk IMX95_CLK_M33>;
> > + clock-names = "gpio", "port";
> > + status = "disabled";
>
> I'm wondering of there should be a comment here that gpio1 usually is under
> exclusive control of SM.
Ok, will add comment.
>
> > + };
> > +
> > + elemu0: mailbox@47520000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47520000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu1: mailbox@47530000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47530000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu2: mailbox@47540000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47540000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu3: mailbox@47550000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47550000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + };
> > +
> > + elemu4: mailbox@47560000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47560000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu5: mailbox@47570000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47570000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + v2x_mu: mailbox@47350000 {
> > + compatible = "fsl,imx95-mu-v2x";
> > + reg = <0x0 0x47350000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + };
> > +
> > + v2x_mu6: mailbox@47320000 {
> > + compatible = "fsl,imx95-mu-v2x";
> > + reg = <0x0 0x47320000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + };
>
> Please sort nodes by address.
Yeah. Fix in v4.
Thanks,
Peng.
>
> Best regards,
> Alexander
>
> > + };
> > +};
> >
> >
>
>
> --
> TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
> Amtsgericht München, HRB 105018
> Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
> http://www.t/
> q-
> group.com%2F&data=05%7C02%7Cpeng.fan%40nxp.com%7C50f2e03eeb9d4
> b5ec44008dc6822023c%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C
> 0%7C638499742474895703%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4
> wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C0%7C%
> 7C%7C&sdata=QQTX4gXs3a%2FXizeqgzpaq3n0vmoQRUYkSufNKVu7LE8%3D
> &reserved=0
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
@ 2024-05-03 0:15 ` Peng Fan
0 siblings, 0 replies; 12+ messages in thread
From: Peng Fan @ 2024-05-03 0:15 UTC (permalink / raw)
To: Alexander Stein, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
linux-arm-kernel
Cc: devicetree, linux-kernel, imx, linux-arm-kernel, Peng Fan (OSS)
> Subject: Re: [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi
>
> Hi Peng,
>
> thanks for your patch.
>
> Am Sonntag, 28. April 2024, 14:22:20 CEST schrieb Peng Fan (OSS):
> > From: Peng Fan <peng.fan@nxp.com>
> >
> > i.MX95 features 6 A55 Cores, ARM Mali GPU, ISP, ML acceleration NPU,
> > and Edgelock secure enclave security. This patch is to add a minimal
> > dtsi, with cpu cores, coresight, scmi, gic, uart, mu, sdhc, lpi2c added.
> >
> > Signed-off-by: Peng Fan <peng.fan@nxp.com>
> > ---
> > arch/arm64/boot/dts/freescale/imx95-clock.h | 187 +++++
> > arch/arm64/boot/dts/freescale/imx95-power.h | 55 ++
> > arch/arm64/boot/dts/freescale/imx95.dtsi | 1152
> +++++++++++++++++++++++++++
> > 3 files changed, 1394 insertions(+)
> >
> > [snip]
> > diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi
> > b/arch/arm64/boot/dts/freescale/imx95.dtsi
> > new file mode 100644
> > index 000000000000..f52023ec7f0c
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
> > [snip]
> > + soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + aips2: bus@42000000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0x0 0x42000000 0x0 0x800000>;
> > + ranges = <0x42000000 0x0 0x42000000
> 0x8000000>,
> > + <0x28000000 0x0 0x28000000
> 0x10000000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + mu7: mailbox@42430000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x42430000 0x10000>;
> > + interrupts = <GIC_SPI 234
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu8: mailbox@42730000 {
>
> Please sort all nodes by address.
Sure. fix in v4.
>
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x42730000 0x10000>;
> > + interrupts = <GIC_SPI 235
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + wdog3: watchdog@42490000 {
> > + compatible = "fsl,imx93-wdt";
> > + reg = <0x42490000 0x10000>;
> > + interrupts = <GIC_SPI 77
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + timeout-sec = <40>;
> > + fsl,ext-reset-output;
>
> Isn't this board specific?
Yeah. Board specific, remove it.
>
> > + status = "disabled";
> > + };
> > +
> > + tpm3: pwm@424e0000 {
> > + compatible = "fsl,imx7ulp-pwm";
> > + reg = <0x424e0000 0x1000>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>;
> > + #pwm-cells = <3>;
> > + status = "disabled";
> > + };
> > [snip]
> > + };
> > +
> > + aips3: bus@42800000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0 0x42800000 0 0x800000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0x42800000 0x0 0x42800000 0x800000>;
> > +
> > + usdhc1: mmc@42850000 {
> > + compatible = "fsl,imx95-usdhc",
> "fsl,imx8mm-usdhc";
> > + reg = <0x42850000 0x10000>;
> > + interrupts = <GIC_SPI 86
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk
> IMX95_CLK_WAKEUPAXI>,
> > + <&scmi_clk IMX95_CLK_USDHC1>;
> > + clock-names = "ipg", "ahb", "per";
> > + assigned-clocks = <&scmi_clk
> IMX95_CLK_USDHC1>;
> > + assigned-clock-parents = <&scmi_clk
> IMX95_CLK_SYSPLL1_PFD1>;
> > + assigned-clock-rates = <400000000>;
> > + bus-width = <8>;
> > + fsl,tuning-start-tap = <1>;
> > + fsl,tuning-step= <2>;
>
> Isn't this board specific? Or is there a hardware limitation?
Yeah, just follow what imx93 has, board could override them.
No hardware limitation as I know.
>
> > + status = "disabled";
> > + };
> > +
> > + usdhc2: mmc@42860000 {
> > + compatible = "fsl,imx95-usdhc",
> "fsl,imx8mm-usdhc";
> > + reg = <0x42860000 0x10000>;
> > + interrupts = <GIC_SPI 87
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk
> IMX95_CLK_WAKEUPAXI>,
> > + <&scmi_clk IMX95_CLK_USDHC2>;
> > + clock-names = "ipg", "ahb", "per";
> > + assigned-clocks = <&scmi_clk
> IMX95_CLK_USDHC2>;
> > + assigned-clock-parents = <&scmi_clk
> IMX95_CLK_SYSPLL1_PFD1>;
> > + assigned-clock-rates = <200000000>;
>
> Why is usdhc2 only 200 MHz but usdhc1 400 MHz?
No specific reason, 400M should also work.
>
> > + bus-width = <4>;
> > + fsl,tuning-start-tap = <1>;
> > + fsl,tuning-step= <2>;
>
> Isn't this board specific? Or is there a hardware limitation?
Yes, just follow what i.MX93 has and board could override them.
>
> > + status = "disabled";
> > + };
> > +
> > + usdhc3: mmc@428b0000 {
> > + compatible = "fsl,imx95-usdhc",
> "fsl,imx8mm-usdhc";
> > + reg = <0x428b0000 0x10000>;
> > + interrupts = <GIC_SPI 191
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk
> IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk
> IMX95_CLK_WAKEUPAXI>,
> > + <&scmi_clk IMX95_CLK_USDHC3>;
> > + clock-names = "ipg", "ahb", "per";
>
> No need to configure IMX95_CLK_USDHC3?
I will add it.
>
> > + bus-width = <4>;
> > + fsl,tuning-start-tap = <1>;
> > + fsl,tuning-step= <2>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + gpio2: gpio@43810000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43810000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + gpio3: gpio@43820000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43820000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + gpio4: gpio@43840000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43840000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + gpio5: gpio@43850000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x43850000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSWAKEUP>,
> > + <&scmi_clk IMX95_CLK_BUSWAKEUP>;
> > + clock-names = "gpio", "port";
> > + };
> > +
> > + aips1: bus@44000000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0x0 0x44000000 0x0 0x800000>;
> > + ranges = <0x44000000 0x0 0x44000000 0x800000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + mu1: mailbox@44220000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x44220000 0x10000>;
> > + interrupts = <GIC_SPI 224
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu2: mailbox@445b0000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x445b0000 0x1000>;
> > + ranges;
> > + interrupts = <GIC_SPI 226
> IRQ_TYPE_LEVEL_HIGH>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + #mbox-cells = <2>;
> > +
> > + sram0: sram@445b1000 {
> > + compatible = "mmio-sram";
> > + reg = <0x445b1000 0x400>;
> > + ranges = <0x0 0x445b1000 0x400>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + scmi_buf0: scmi-sram-section@0 {
> > + compatible = "arm,scmi-
> shmem";
> > + reg = <0x0 0x80>;
> > + };
> > +
> > + scmi_buf1: scmi-sram-section@80
> {
> > + compatible = "arm,scmi-
> shmem";
> > + reg = <0x80 0x80>;
> > + };
> > + };
>
> I guess this MU depends on the system manager firmware, no?
Yes, depends on firmware.
>
> > + };
> > +
> > + mu3: mailbox@445d0000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x445d0000 0x10000>;
> > + interrupts = <GIC_SPI 228
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu4: mailbox@445f0000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x445f0000 0x10000>;
> > + interrupts = <GIC_SPI 230
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + mu6: mailbox@44630000 {
> > + compatible = "fsl,imx95-mu";
> > + reg = <0x44630000 0x10000>;
> > + interrupts = <GIC_SPI 206
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + tpm1: pwm@44310000 {
> > + compatible = "fsl,imx7ulp-pwm";
> > + reg = <0x44310000 0x1000>;
> > + clocks = <&scmi_clk IMX95_CLK_BUSAON>;
> > + #pwm-cells = <3>;
> > + status = "disabled";
> > + };
> > +
> > + tpm2: pwm@44320000 {
> > + compatible = "fsl,imx7ulp-pwm";
> > + reg = <0x44320000 0x1000>;
> > + clocks = <&scmi_clk IMX95_CLK_TPM2>;
> > + #pwm-cells = <3>;
> > + status = "disabled";
> > + };
> > +
> > + lpi2c1: i2c@44340000 {
> > + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-
> lpi2c";
> > + reg = <0x44340000 0x10000>;
> > + interrupts = <GIC_SPI 13
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPI2C1>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpi2c2: i2c@44350000 {
> > + compatible = "fsl,imx95-lpi2c", "fsl,imx7ulp-
> lpi2c";
> > + reg = <0x44350000 0x10000>;
> > + interrupts = <GIC_SPI 14
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPI2C2>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpspi1: spi@44360000 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "fsl,imx95-spi", "fsl,imx7ulp-
> spi";
> > + reg = <0x44360000 0x10000>;
> > + interrupts = <GIC_SPI 16
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPSPI1>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpspi2: spi@44370000 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "fsl,imx95-spi", "fsl,imx7ulp-
> spi";
> > + reg = <0x44370000 0x10000>;
> > + interrupts = <GIC_SPI 17
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPSPI2>,
> > + <&scmi_clk IMX95_CLK_BUSAON>;
> > + clock-names = "per", "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpuart1: serial@44380000 {
> > + compatible = "fsl,imx95-lpuart",
> "fsl,imx8ulp-lpuart",
> > + "fsl,imx7ulp-lpuart";
> > + reg = <0x44380000 0x1000>;
> > + interrupts = <GIC_SPI 19
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPUART1>;
> > + clock-names = "ipg";
> > + status = "disabled";
> > + };
> > +
> > + lpuart2: serial@44390000 {
> > + compatible = "fsl,imx95-lpuart",
> "fsl,imx8ulp-lpuart",
> > + "fsl,imx7ulp-lpuart";
> > + reg = <0x44390000 0x1000>;
> > + interrupts = <GIC_SPI 20
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_LPUART2>;
> > + clock-names = "ipg";
> > + status = "disabled";
> > + };
> > +
> > + adc1: adc@44530000 {
> > + compatible = "nxp,imx93-adc";
> > + reg = <0x44530000 0x10000>;
> > + interrupts = <GIC_SPI 199
> IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 200
> IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 201
> IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&scmi_clk IMX95_CLK_ADC>;
> > + clock-names = "ipg";
> > + status = "disabled";
> > + };
>
> Please sort the nodes by address.
Sure.
>
> > + };
> > +
> > + aips4: bus@49000000 {
> > + compatible = "fsl,aips-bus", "simple-bus";
> > + reg = <0x0 0x49000000 0x0 0x800000>;
> > + ranges = <0x49000000 0x0 0x49000000 0x800000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + smmu: iommu@490d0000 {
> > + compatible = "arm,smmu-v3";
> > + reg = <0x490d0000 0x100000>;
> > + interrupts = <GIC_SPI 325
> IRQ_TYPE_EDGE_RISING>,
> > + <GIC_SPI 328
> IRQ_TYPE_EDGE_RISING>,
> > + <GIC_SPI 334
> IRQ_TYPE_EDGE_RISING>,
> > + <GIC_SPI 326
> IRQ_TYPE_EDGE_RISING>;
> > + interrupt-names = "eventq", "gerror", "priq",
> "cmdq-sync";
> > + #iommu-cells = <1>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + gpio1: gpio@47400000 {
> > + compatible = "fsl,imx95-gpio", "fsl,imx8ulp-gpio";
> > + reg = <0x0 0x47400000 0x0 0x1000>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + clocks = <&scmi_clk IMX95_CLK_M33>,
> > + <&scmi_clk IMX95_CLK_M33>;
> > + clock-names = "gpio", "port";
> > + status = "disabled";
>
> I'm wondering of there should be a comment here that gpio1 usually is under
> exclusive control of SM.
Ok, will add comment.
>
> > + };
> > +
> > + elemu0: mailbox@47520000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47520000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu1: mailbox@47530000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47530000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu2: mailbox@47540000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47540000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu3: mailbox@47550000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47550000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + };
> > +
> > + elemu4: mailbox@47560000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47560000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + elemu5: mailbox@47570000 {
> > + compatible = "fsl,imx95-mu-ele";
> > + reg = <0x0 0x47570000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + status = "disabled";
> > + };
> > +
> > + v2x_mu: mailbox@47350000 {
> > + compatible = "fsl,imx95-mu-v2x";
> > + reg = <0x0 0x47350000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + };
> > +
> > + v2x_mu6: mailbox@47320000 {
> > + compatible = "fsl,imx95-mu-v2x";
> > + reg = <0x0 0x47320000 0x0 0x10000>;
> > + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
> > + #mbox-cells = <2>;
> > + };
>
> Please sort nodes by address.
Yeah. Fix in v4.
Thanks,
Peng.
>
> Best regards,
> Alexander
>
> > + };
> > +};
> >
> >
>
>
> --
> TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
> Amtsgericht München, HRB 105018
> Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
> http://www.t/
> q-
> group.com%2F&data=05%7C02%7Cpeng.fan%40nxp.com%7C50f2e03eeb9d4
> b5ec44008dc6822023c%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C
> 0%7C638499742474895703%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4
> wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C0%7C%
> 7C%7C&sdata=QQTX4gXs3a%2FXizeqgzpaq3n0vmoQRUYkSufNKVu7LE8%3D
> &reserved=0
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2024-05-03 0:16 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-04-28 12:22 [PATCH v3 0/3] arm64: dts: add i.MX95 and EVK board Peng Fan (OSS)
2024-04-28 12:22 ` Peng Fan (OSS)
2024-04-28 12:22 ` [PATCH v3 1/3] dt-bindings: arm: fsl: add i.MX95 19x19 " Peng Fan (OSS)
2024-04-28 12:22 ` Peng Fan (OSS)
2024-04-28 12:22 ` [PATCH v3 2/3] arm64: dts: freescale: add i.MX95 basic dtsi Peng Fan (OSS)
2024-04-28 12:22 ` Peng Fan (OSS)
2024-04-29 7:57 ` Alexander Stein
2024-04-29 7:57 ` Alexander Stein
2024-05-03 0:15 ` Peng Fan
2024-05-03 0:15 ` Peng Fan
2024-04-28 12:22 ` [PATCH v3 3/3] arm64: dts: freescale: add i.MX95 19x19 EVK minimal board dts Peng Fan (OSS)
2024-04-28 12:22 ` Peng Fan (OSS)
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.