All of lore.kernel.org
 help / color / mirror / Atom feed
From: Tim Harvey <tharvey@gateworks.com>
To: Tom Rini <trini@konsulko.com>, Tim Harvey <tharvey@gateworks.com>,
	Simon Glass <sjg@chromium.org>, Marek Vasut <marex@denx.de>,
	Fabio Estevam <festevam@gmail.com>,
	Jaehoon Chung <jh80.chung@samsung.com>,
	u-boot@lists.denx.de, Dragan Simic <dsimic@manjaro.org>,
	Ulf Hansson <ulf.hansson@linaro.org>,
	Avri Altman <avri.altman@wdc.com>
Subject: [PATCH 1/3 v4] mmc: use an enumerated type to represent PARTITION_CONFIG fields
Date: Mon, 13 May 2024 16:29:05 -0700	[thread overview]
Message-ID: <20240513232907.2738959-2-tharvey@gateworks.com> (raw)
In-Reply-To: <20240513232907.2738959-1-tharvey@gateworks.com>

Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
  Boot Area Partition 1
  Boot Area Partition 2
  RPMB Partition
  General Purpose Partition 1
  General Purpose Partition 2
  General Purpose Partition 3
  General Purpose Partition 4
  User Data Area

These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
  0x0: No boot acknowledge sent (default
  0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
  0x0: Device not boot enabled (default)
  0x1: Boot Area partition 1 enabled for boot
  0x2: Boot Area partition 2 enabled for boot
  0x3-0x6: Reserved
  0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
  0x0: No access to boot partition (default)
  0x1: Boot Area partition 1
  0x2: Boot Area partition 2
  0x3: Replay Protected Memory Block (RPMB)
  0x4: Access to General Purpose partition 1
  0x5: Access to General Purpose partition 2
  0x6: Access to General Purpose partition 3
  0x7: Access to General Purpose partition 4

Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.

You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.

U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:

There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field which is also the value used to specify the
hardware partition of the various mmc_switch incarnations.

To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.

This represents no code changes.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v4: new patch in this series
---
 arch/arm/mach-imx/image-container.c | 10 +++++-----
 arch/arm/mach-sunxi/board.c         |  2 +-
 board/gateworks/venice/spl.c        |  4 ++--
 board/gateworks/venice/venice.c     | 22 +++++++++++-----------
 board/purism/librem5/librem5.c      |  4 ++--
 board/storopack/smegw01/smegw01.c   |  4 ++--
 cmd/mvebu/bubt.c                    |  4 ++--
 common/spl/spl_mmc.c                |  4 ++--
 include/mmc.h                       | 20 ++++++++++++++++++++
 9 files changed, 47 insertions(+), 27 deletions(-)

diff --git a/arch/arm/mach-imx/image-container.c b/arch/arm/mach-imx/image-container.c
index 35da0ae04258..bcd40889f0fa 100644
--- a/arch/arm/mach-imx/image-container.c
+++ b/arch/arm/mach-imx/image-container.c
@@ -205,7 +205,7 @@ static unsigned long get_boot_device_offset(void *dev, int dev_type)
 		} else {
 			u8 part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
 
-			if (part == 1 || part == 2) {
+			if (part == EMMC_BOOT_PART_BOOT1 || part == EMMC_BOOT_PART_BOOT2) {
 				if (is_imx8qxp() && is_soc_rev(CHIP_REV_B))
 					offset = CONTAINER_HDR_MMCSD_OFFSET;
 				else
@@ -294,15 +294,15 @@ int spl_mmc_emmc_boot_partition(struct mmc *mmc)
 	int part;
 
 	part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
-	if (part == 1 || part == 2) {
+	if (part == EMMC_BOOT_PART_BOOT1 || part == EMMC_BOOT_PART_BOOT2) {
 		unsigned long sec_set_off = 0;
 		bool sec_boot = false;
 
 		sec_boot = check_secondary_cnt_set(&sec_set_off);
 		if (sec_boot)
-			part = (part == 1) ? 2 : 1;
-	} else if (part == 7) {
-		part = 0;
+			part = (part == EMMC_BOOT_PART_BOOT1) ? EMMC_HWPART_BOOT2 : EMMC_HWPART_BOOT1;
+	} else if (part == EMMC_BOOT_PART_USER) {
+		part = EMMC_HWPART_DEFAULT;
 	}
 
 	return part;
diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c
index 0140b07d32a6..860e7058b69c 100644
--- a/arch/arm/mach-sunxi/board.c
+++ b/arch/arm/mach-sunxi/board.c
@@ -396,7 +396,7 @@ static bool sunxi_valid_emmc_boot(struct mmc *mmc)
 		return false;
 
 	/* Partition 0 is the user data partition, bootpart must be 1 or 2. */
-	if (bootpart != 1 && bootpart != 2)
+	if (bootpart != EMMC_BOOT_PART_BOOT1 && bootpart != EMMC_BOOT_PART_BOOT2)
 		return false;
 
 	/* Failure to switch to the boot partition is fatal. */
diff --git a/board/gateworks/venice/spl.c b/board/gateworks/venice/spl.c
index 3b0f11f2fd0f..6f6dea84feee 100644
--- a/board/gateworks/venice/spl.c
+++ b/board/gateworks/venice/spl.c
@@ -353,8 +353,8 @@ unsigned long board_spl_mmc_get_uboot_raw_sector(struct mmc *mmc, unsigned long
 {
 	if (!IS_SD(mmc)) {
 		switch (EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config)) {
-		case 1:
-		case 2:
+		case EMMC_BOOT_PART_BOOT1:
+		case EMMC_BOOT_PART_BOOT2:
 			if (IS_ENABLED(CONFIG_IMX8MN) || IS_ENABLED(CONFIG_IMX8MP))
 				raw_sect -= 32 * 2;
 			break;
diff --git a/board/gateworks/venice/venice.c b/board/gateworks/venice/venice.c
index 5b105d7659e4..44ed4e4598e1 100644
--- a/board/gateworks/venice/venice.c
+++ b/board/gateworks/venice/venice.c
@@ -173,20 +173,20 @@ int board_late_init(void)
 			int bootpart;
 
 			switch (EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config)) {
-			case 1: /* boot0 */
-				bootpart = 1;
+			case EMMC_BOOT_PART_BOOT1:
+				bootpart = EMMC_HWPART_BOOT1;
 				break;
-			case 2: /* boot1 */
-				bootpart = 2;
+			case EMMC_BOOT_PART_BOOT2:
+				bootpart = EMMC_HWPART_BOOT2;
 				break;
-			case 7: /* user */
+			case EMMC_BOOT_PART_USER:
 			default:
-				bootpart = 0;
+				bootpart = EMMC_HWPART_DEFAULT;
 				break;
 			}
 			/* IMX8MP/IMX8MN BOOTROM v2 uses offset=0 for boot parts */
 			if ((IS_ENABLED(CONFIG_IMX8MN) || IS_ENABLED(CONFIG_IMX8MP)) &&
-			    (bootpart == 1 || bootpart == 2))
+			    (bootpart == EMMC_BOOT_PART_BOOT1 || bootpart == EMMC_BOOT_PART_BOOT2))
 				bootblk = 0;
 			env_set_hex("bootpart", bootpart);
 			env_set_hex("bootblk", bootblk);
@@ -217,10 +217,10 @@ uint mmc_get_env_part(struct mmc *mmc)
 {
 	if (!IS_SD(mmc)) {
 		switch (EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config)) {
-		case 1:
-			return 1;
-		case 2:
-			return 2;
+		case EMMC_BOOT_PART_BOOT1:
+			return EMMC_HWPART_BOOT1;
+		case EMMC_BOOT_PART_BOOT2:
+			return EMMC_HWPART_BOOT2;
 		}
 	}
 
diff --git a/board/purism/librem5/librem5.c b/board/purism/librem5/librem5.c
index d0249e71f09a..3f1a8e385d72 100644
--- a/board/purism/librem5/librem5.c
+++ b/board/purism/librem5/librem5.c
@@ -43,8 +43,8 @@ uint board_mmc_get_env_part(struct mmc *mmc)
 {
 	uint part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
 
-	if (part == 7)
-		part = 0;
+	if (part == EMMC_BOOT_PART_USER)
+		part = EMMC_HWPART_DEFAULT;
 	return part;
 }
 #endif
diff --git a/board/storopack/smegw01/smegw01.c b/board/storopack/smegw01/smegw01.c
index 345191b31c29..d1f474bc7a14 100644
--- a/board/storopack/smegw01/smegw01.c
+++ b/board/storopack/smegw01/smegw01.c
@@ -106,8 +106,8 @@ uint mmc_get_env_part(struct mmc *mmc)
 {
 	uint part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
 
-	if (part == 7)
-		part = 0;
+	if (part == EMMC_BOOT_PART_USER)
+		part = EMMC_HWPART_DEFAULT;
 	return part;
 }
 
diff --git a/cmd/mvebu/bubt.c b/cmd/mvebu/bubt.c
index 744b1c20aa83..1e3f5bf7add6 100644
--- a/cmd/mvebu/bubt.c
+++ b/cmd/mvebu/bubt.c
@@ -224,8 +224,8 @@ static int mmc_burn_image(size_t image_size)
 #endif
 
 	part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
-	if (part == 7)
-		part = 0;
+	if (part == EMMC_BOOT_PART_USER)
+		part = EMMC_HWPART_DEFAULT;
 
 #ifdef CONFIG_BLK
 	err = blk_dselect_hwpart(blk_desc, part);
diff --git a/common/spl/spl_mmc.c b/common/spl/spl_mmc.c
index 3d032bb27ce3..fd5154dad7c4 100644
--- a/common/spl/spl_mmc.c
+++ b/common/spl/spl_mmc.c
@@ -320,8 +320,8 @@ int default_spl_mmc_emmc_boot_partition(struct mmc *mmc)
 	 * which is the first physical partition (0).
 	 */
 	part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
-	if (part == 7)
-		part = 0;
+	if (part == EMMC_BOOT_PART_USER)
+		part = EMMC_HWPART_DEFAULT;
 #endif
 	return part;
 }
diff --git a/include/mmc.h b/include/mmc.h
index 4b8327f1f93b..0f3f1ed6aaa3 100644
--- a/include/mmc.h
+++ b/include/mmc.h
@@ -381,6 +381,26 @@ enum mmc_voltage {
 #define MMC_TIMING_MMC_HS200	9
 #define MMC_TIMING_MMC_HS400	10
 
+/* emmc PARTITION_CONFIG BOOT_PARTITION_ENABLE values */
+enum emmc_boot_part {
+	EMMC_BOOT_PART_DEFAULT = 0,
+	EMMC_BOOT_PART_BOOT1 = 1,
+	EMMC_BOOT_PART_BOOT2 = 2,
+	EMMC_BOOT_PART_USER = 7,
+};
+
+/* emmc PARTITION_CONFIG ACCESS_ENABLE values */
+enum emmc_hwpart {
+	EMMC_HWPART_DEFAULT = 0, /* user */
+	EMMC_HWPART_BOOT1 = 1,
+	EMMC_HWPART_BOOT2 = 2,
+	EMMC_HWPART_RPMB = 3,
+	EMMC_HWPART_GP1 = 4,
+	EMMC_HWPART_GP2 = 5,
+	EMMC_HWPART_GP3 = 6,
+	EMMC_HWPART_GP4 = 7,
+};
+
 /* Driver model support */
 
 /**
-- 
2.25.1


  reply	other threads:[~2024-05-13 23:29 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-05-13 23:29 [PATCH 0/3 v4] provide names for emmc hardware partitions Tim Harvey
2024-05-13 23:29 ` Tim Harvey [this message]
2024-05-13 23:29 ` [PATCH 2/3 v4] mmc: allow use of hardware partition names for mmc partconf Tim Harvey
2024-05-13 23:29 ` [PATCH 3/3 v4] venice: show emmc boot hardware partition Tim Harvey

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20240513232907.2738959-2-tharvey@gateworks.com \
    --to=tharvey@gateworks.com \
    --cc=avri.altman@wdc.com \
    --cc=dsimic@manjaro.org \
    --cc=festevam@gmail.com \
    --cc=jh80.chung@samsung.com \
    --cc=marex@denx.de \
    --cc=sjg@chromium.org \
    --cc=trini@konsulko.com \
    --cc=u-boot@lists.denx.de \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.