* [PATCH v2 13/22] ath9k: cleanup MCI indentation
@ 2012-05-24 4:03 Sujith Manoharan
0 siblings, 0 replies; only message in thread
From: Sujith Manoharan @ 2012-05-24 4:03 UTC (permalink / raw)
To: linville; +Cc: linux-wireless
From: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
---
drivers/net/wireless/ath/ath9k/ar9003_mci.c | 435 +++++++++++++--------------
1 file changed, 215 insertions(+), 220 deletions(-)
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_mci.c b/drivers/net/wireless/ath/ath9k/ar9003_mci.c
index b501bf1..854dff6 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_mci.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_mci.c
@@ -35,31 +35,30 @@ static int ar9003_mci_wait_for_interrupt(struct ath_hw *ah, u32 address,
struct ath_common *common = ath9k_hw_common(ah);
while (time_out) {
- if (REG_READ(ah, address) & bit_position) {
- REG_WRITE(ah, address, bit_position);
-
- if (address == AR_MCI_INTERRUPT_RX_MSG_RAW) {
- if (bit_position &
- AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE)
- ar9003_mci_reset_req_wakeup(ah);
-
- if (bit_position &
- (AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING |
- AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING))
- REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
- AR_MCI_INTERRUPT_REMOTE_SLEEP_UPDATE);
-
- REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
- AR_MCI_INTERRUPT_RX_MSG);
- }
- break;
- }
+ if (!(REG_READ(ah, address) & bit_position)) {
+ udelay(10);
+ time_out -= 10;
- udelay(10);
- time_out -= 10;
+ if (time_out < 0)
+ break;
+ else
+ continue;
+ }
+ REG_WRITE(ah, address, bit_position);
- if (time_out < 0)
+ if (address != AR_MCI_INTERRUPT_RX_MSG_RAW)
break;
+
+ if (bit_position & AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE)
+ ar9003_mci_reset_req_wakeup(ah);
+
+ if (bit_position & (AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING |
+ AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING))
+ REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
+ AR_MCI_INTERRUPT_REMOTE_SLEEP_UPDATE);
+
+ REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, AR_MCI_INTERRUPT_RX_MSG);
+ break;
}
if (time_out <= 0) {
@@ -127,14 +126,13 @@ static void ar9003_mci_send_coex_version_query(struct ath_hw *ah,
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 payload[4] = {0, 0, 0, 0};
- if (!mci->bt_version_known &&
- (mci->bt_state != MCI_BT_SLEEP)) {
- MCI_GPM_SET_TYPE_OPCODE(payload,
- MCI_GPM_COEX_AGENT,
- MCI_GPM_COEX_VERSION_QUERY);
- ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16,
- wait_done, true);
- }
+ if (mci->bt_version_known ||
+ (mci->bt_state == MCI_BT_SLEEP))
+ return;
+
+ MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT,
+ MCI_GPM_COEX_VERSION_QUERY);
+ ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, wait_done, true);
}
static void ar9003_mci_send_coex_version_response(struct ath_hw *ah,
@@ -158,15 +156,14 @@ static void ar9003_mci_send_coex_wlan_channels(struct ath_hw *ah,
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 *payload = &mci->wlan_channels[0];
- if ((mci->wlan_channels_update == true) &&
- (mci->bt_state != MCI_BT_SLEEP)) {
- MCI_GPM_SET_TYPE_OPCODE(payload,
- MCI_GPM_COEX_AGENT,
- MCI_GPM_COEX_WLAN_CHANNELS);
- ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16,
- wait_done, true);
- MCI_GPM_SET_TYPE_OPCODE(payload, 0xff, 0xff);
- }
+ if (!mci->wlan_channels_update ||
+ (mci->bt_state == MCI_BT_SLEEP))
+ return;
+
+ MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT,
+ MCI_GPM_COEX_WLAN_CHANNELS);
+ ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16, wait_done, true);
+ MCI_GPM_SET_TYPE_OPCODE(payload, 0xff, 0xff);
}
static void ar9003_mci_send_coex_bt_status_query(struct ath_hw *ah,
@@ -174,29 +171,30 @@ static void ar9003_mci_send_coex_bt_status_query(struct ath_hw *ah,
{
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 payload[4] = {0, 0, 0, 0};
- bool query_btinfo = !!(query_type & (MCI_GPM_COEX_QUERY_BT_ALL_INFO |
- MCI_GPM_COEX_QUERY_BT_TOPOLOGY));
+ bool query_btinfo;
- if (mci->bt_state != MCI_BT_SLEEP) {
-
- MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT,
- MCI_GPM_COEX_STATUS_QUERY);
+ if (mci->bt_state == MCI_BT_SLEEP)
+ return;
- *(((u8 *)payload) + MCI_GPM_COEX_B_BT_BITMAP) = query_type;
+ query_btinfo = !!(query_type & (MCI_GPM_COEX_QUERY_BT_ALL_INFO |
+ MCI_GPM_COEX_QUERY_BT_TOPOLOGY));
+ MCI_GPM_SET_TYPE_OPCODE(payload, MCI_GPM_COEX_AGENT,
+ MCI_GPM_COEX_STATUS_QUERY);
- /*
- * If bt_status_query message is not sent successfully,
- * then need_flush_btinfo should be set again.
- */
- if (!ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16,
- wait_done, true)) {
- if (query_btinfo)
- mci->need_flush_btinfo = true;
- }
+ *(((u8 *)payload) + MCI_GPM_COEX_B_BT_BITMAP) = query_type;
+ /*
+ * If bt_status_query message is not sent successfully,
+ * then need_flush_btinfo should be set again.
+ */
+ if (!ar9003_mci_send_message(ah, MCI_GPM, 0, payload, 16,
+ wait_done, true)) {
if (query_btinfo)
- mci->query_bt = false;
+ mci->need_flush_btinfo = true;
}
+
+ if (query_btinfo)
+ mci->query_bt = false;
}
static void ar9003_mci_send_coex_halt_bt_gpm(struct ath_hw *ah, bool halt,
@@ -241,73 +239,73 @@ static void ar9003_mci_prep_interface(struct ath_hw *ah)
ar9003_mci_remote_reset(ah, true);
ar9003_mci_send_req_wake(ah, true);
- if (ar9003_mci_wait_for_interrupt(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
- AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING, 500)) {
+ if (!ar9003_mci_wait_for_interrupt(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
+ AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING, 500))
+ goto clear_redunt;
- mci->bt_state = MCI_BT_AWAKE;
+ mci->bt_state = MCI_BT_AWAKE;
- /*
- * we don't need to send more remote_reset at this moment.
- * If BT receive first remote_reset, then BT HW will
- * be cleaned up and will be able to receive req_wake
- * and BT HW will respond sys_waking.
- * In this case, WLAN will receive BT's HW sys_waking.
- * Otherwise, if BT SW missed initial remote_reset,
- * that remote_reset will still clean up BT MCI RX,
- * and the req_wake will wake BT up,
- * and BT SW will respond this req_wake with a remote_reset and
- * sys_waking. In this case, WLAN will receive BT's SW
- * sys_waking. In either case, BT's RX is cleaned up. So we
- * don't need to reply BT's remote_reset now, if any.
- * Similarly, if in any case, WLAN can receive BT's sys_waking,
- * that means WLAN's RX is also fine.
- */
- ar9003_mci_send_sys_waking(ah, true);
- udelay(10);
+ /*
+ * we don't need to send more remote_reset at this moment.
+ * If BT receive first remote_reset, then BT HW will
+ * be cleaned up and will be able to receive req_wake
+ * and BT HW will respond sys_waking.
+ * In this case, WLAN will receive BT's HW sys_waking.
+ * Otherwise, if BT SW missed initial remote_reset,
+ * that remote_reset will still clean up BT MCI RX,
+ * and the req_wake will wake BT up,
+ * and BT SW will respond this req_wake with a remote_reset and
+ * sys_waking. In this case, WLAN will receive BT's SW
+ * sys_waking. In either case, BT's RX is cleaned up. So we
+ * don't need to reply BT's remote_reset now, if any.
+ * Similarly, if in any case, WLAN can receive BT's sys_waking,
+ * that means WLAN's RX is also fine.
+ */
+ ar9003_mci_send_sys_waking(ah, true);
+ udelay(10);
- /*
- * Set BT priority interrupt value to be 0xff to
- * avoid having too many BT PRIORITY interrupts.
- */
- REG_WRITE(ah, AR_MCI_BT_PRI0, 0xFFFFFFFF);
- REG_WRITE(ah, AR_MCI_BT_PRI1, 0xFFFFFFFF);
- REG_WRITE(ah, AR_MCI_BT_PRI2, 0xFFFFFFFF);
- REG_WRITE(ah, AR_MCI_BT_PRI3, 0xFFFFFFFF);
- REG_WRITE(ah, AR_MCI_BT_PRI, 0X000000FF);
+ /*
+ * Set BT priority interrupt value to be 0xff to
+ * avoid having too many BT PRIORITY interrupts.
+ */
+ REG_WRITE(ah, AR_MCI_BT_PRI0, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_MCI_BT_PRI1, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_MCI_BT_PRI2, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_MCI_BT_PRI3, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_MCI_BT_PRI, 0X000000FF);
- /*
- * A contention reset will be received after send out
- * sys_waking. Also BT priority interrupt bits will be set.
- * Clear those bits before the next step.
- */
+ /*
+ * A contention reset will be received after send out
+ * sys_waking. Also BT priority interrupt bits will be set.
+ * Clear those bits before the next step.
+ */
- REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
- AR_MCI_INTERRUPT_RX_MSG_CONT_RST);
- REG_WRITE(ah, AR_MCI_INTERRUPT_RAW,
- AR_MCI_INTERRUPT_BT_PRI);
+ REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
+ AR_MCI_INTERRUPT_RX_MSG_CONT_RST);
+ REG_WRITE(ah, AR_MCI_INTERRUPT_RAW, AR_MCI_INTERRUPT_BT_PRI);
- if (mci->is_2g) {
- ar9003_mci_send_lna_transfer(ah, true);
- udelay(5);
- }
+ if (mci->is_2g) {
+ ar9003_mci_send_lna_transfer(ah, true);
+ udelay(5);
+ }
- if ((mci->is_2g && !mci->update_2g5g)) {
- if (ar9003_mci_wait_for_interrupt(ah,
- AR_MCI_INTERRUPT_RX_MSG_RAW,
- AR_MCI_INTERRUPT_RX_MSG_LNA_INFO,
- mci_timeout))
- ath_dbg(common, MCI,
- "MCI WLAN has control over the LNA & BT obeys it\n");
- else
- ath_dbg(common, MCI,
- "MCI BT didn't respond to LNA_TRANS\n");
- }
+ if ((mci->is_2g && !mci->update_2g5g)) {
+ if (ar9003_mci_wait_for_interrupt(ah,
+ AR_MCI_INTERRUPT_RX_MSG_RAW,
+ AR_MCI_INTERRUPT_RX_MSG_LNA_INFO,
+ mci_timeout))
+ ath_dbg(common, MCI,
+ "MCI WLAN has control over the LNA & BT obeys it\n");
+ else
+ ath_dbg(common, MCI,
+ "MCI BT didn't respond to LNA_TRANS\n");
}
+clear_redunt:
/* Clear the extra redundant SYS_WAKING from BT */
if ((mci->bt_state == MCI_BT_AWAKE) &&
- (REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
- AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING)) &&
+ (REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
+ AR_MCI_INTERRUPT_RX_MSG_SYS_WAKING)) &&
(REG_READ_FIELD(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
AR_MCI_INTERRUPT_RX_MSG_SYS_SLEEPING) == 0)) {
REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
@@ -614,9 +612,9 @@ static u32 ar9003_mci_wait_for_gpm(struct ath_hw *ah, u8 gpm_type,
}
break;
}
- } else if ((recv_type == gpm_type) && (recv_opcode == gpm_opcode)) {
+ } else if ((recv_type == gpm_type) &&
+ (recv_opcode == gpm_opcode))
break;
- }
/*
* check if it's cal_grant
@@ -730,38 +728,38 @@ int ar9003_mci_end_reset(struct ath_hw *ah, struct ath9k_channel *chan,
if (!IS_CHAN_2GHZ(chan) || (mci_hw->bt_state != MCI_BT_SLEEP))
goto exit;
- if (ar9003_mci_check_int(ah, AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET) ||
- ar9003_mci_check_int(ah, AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE)) {
+ if (!ar9003_mci_check_int(ah, AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET) &&
+ !ar9003_mci_check_int(ah, AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE))
+ goto exit;
- /*
- * BT is sleeping. Check if BT wakes up during
- * WLAN calibration. If BT wakes up during
- * WLAN calibration, need to go through all
- * message exchanges again and recal.
- */
- REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
- AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET |
- AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE);
+ /*
+ * BT is sleeping. Check if BT wakes up during
+ * WLAN calibration. If BT wakes up during
+ * WLAN calibration, need to go through all
+ * message exchanges again and recal.
+ */
+ REG_WRITE(ah, AR_MCI_INTERRUPT_RX_MSG_RAW,
+ (AR_MCI_INTERRUPT_RX_MSG_REMOTE_RESET |
+ AR_MCI_INTERRUPT_RX_MSG_REQ_WAKE));
- ar9003_mci_remote_reset(ah, true);
- ar9003_mci_send_sys_waking(ah, true);
- udelay(1);
+ ar9003_mci_remote_reset(ah, true);
+ ar9003_mci_send_sys_waking(ah, true);
+ udelay(1);
- if (IS_CHAN_2GHZ(chan))
- ar9003_mci_send_lna_transfer(ah, true);
+ if (IS_CHAN_2GHZ(chan))
+ ar9003_mci_send_lna_transfer(ah, true);
- mci_hw->bt_state = MCI_BT_AWAKE;
+ mci_hw->bt_state = MCI_BT_AWAKE;
- if (caldata) {
- caldata->done_txiqcal_once = false;
- caldata->done_txclcal_once = false;
- caldata->rtt_done = false;
- }
+ if (caldata) {
+ caldata->done_txiqcal_once = false;
+ caldata->done_txclcal_once = false;
+ caldata->rtt_done = false;
+ }
- if (!ath9k_hw_init_cal(ah, chan))
- return -EIO;
+ if (!ath9k_hw_init_cal(ah, chan))
+ return -EIO;
- }
exit:
ar9003_mci_enable_interrupt(ah);
return 0;
@@ -797,29 +795,27 @@ static void ar9003_mci_osla_setup(struct ath_hw *ah, bool enable)
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 thresh;
- if (enable) {
- REG_RMW_FIELD(ah, AR_MCI_SCHD_TABLE_2,
- AR_MCI_SCHD_TABLE_2_HW_BASED, 1);
- REG_RMW_FIELD(ah, AR_MCI_SCHD_TABLE_2,
- AR_MCI_SCHD_TABLE_2_MEM_BASED, 1);
-
- if (!(mci->config & ATH_MCI_CONFIG_DISABLE_AGGR_THRESH)) {
- thresh = MS(mci->config, ATH_MCI_CONFIG_AGGR_THRESH);
- REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
- AR_BTCOEX_CTRL_AGGR_THRESH, thresh);
- REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
- AR_BTCOEX_CTRL_TIME_TO_NEXT_BT_THRESH_EN, 1);
- } else {
- REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
- AR_BTCOEX_CTRL_TIME_TO_NEXT_BT_THRESH_EN, 0);
- }
-
- REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
- AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN, 1);
- } else {
+ if (!enable) {
REG_CLR_BIT(ah, AR_BTCOEX_CTRL,
AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN);
+ return;
}
+ REG_RMW_FIELD(ah, AR_MCI_SCHD_TABLE_2, AR_MCI_SCHD_TABLE_2_HW_BASED, 1);
+ REG_RMW_FIELD(ah, AR_MCI_SCHD_TABLE_2,
+ AR_MCI_SCHD_TABLE_2_MEM_BASED, 1);
+
+ if (!(mci->config & ATH_MCI_CONFIG_DISABLE_AGGR_THRESH)) {
+ thresh = MS(mci->config, ATH_MCI_CONFIG_AGGR_THRESH);
+ REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
+ AR_BTCOEX_CTRL_AGGR_THRESH, thresh);
+ REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
+ AR_BTCOEX_CTRL_TIME_TO_NEXT_BT_THRESH_EN, 1);
+ } else
+ REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
+ AR_BTCOEX_CTRL_TIME_TO_NEXT_BT_THRESH_EN, 0);
+
+ REG_RMW_FIELD(ah, AR_BTCOEX_CTRL,
+ AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN, 1);
}
void ar9003_mci_reset(struct ath_hw *ah, bool en_int, bool is_2g,
@@ -942,26 +938,27 @@ static void ar9003_mci_send_2g5g_status(struct ath_hw *ah, bool wait_done)
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
u32 new_flags, to_set, to_clear;
- if (mci->update_2g5g && (mci->bt_state != MCI_BT_SLEEP)) {
- if (mci->is_2g) {
- new_flags = MCI_2G_FLAGS;
- to_clear = MCI_2G_FLAGS_CLEAR_MASK;
- to_set = MCI_2G_FLAGS_SET_MASK;
- } else {
- new_flags = MCI_5G_FLAGS;
- to_clear = MCI_5G_FLAGS_CLEAR_MASK;
- to_set = MCI_5G_FLAGS_SET_MASK;
- }
+ if (!mci->update_2g5g || (mci->bt_state == MCI_BT_SLEEP))
+ return;
- if (to_clear)
- ar9003_mci_send_coex_bt_flags(ah, wait_done,
+ if (mci->is_2g) {
+ new_flags = MCI_2G_FLAGS;
+ to_clear = MCI_2G_FLAGS_CLEAR_MASK;
+ to_set = MCI_2G_FLAGS_SET_MASK;
+ } else {
+ new_flags = MCI_5G_FLAGS;
+ to_clear = MCI_5G_FLAGS_CLEAR_MASK;
+ to_set = MCI_5G_FLAGS_SET_MASK;
+ }
+
+ if (to_clear)
+ ar9003_mci_send_coex_bt_flags(ah, wait_done,
MCI_GPM_COEX_BT_FLAGS_CLEAR,
to_clear);
- if (to_set)
- ar9003_mci_send_coex_bt_flags(ah, wait_done,
+ if (to_set)
+ ar9003_mci_send_coex_bt_flags(ah, wait_done,
MCI_GPM_COEX_BT_FLAGS_SET,
to_set);
- }
}
static void ar9003_mci_queue_unsent_gpm(struct ath_hw *ah, u8 header,
@@ -1017,34 +1014,34 @@ void ar9003_mci_2g5g_switch(struct ath_hw *ah, bool wait_done)
{
struct ath9k_hw_mci *mci = &ah->btcoex_hw.mci;
- if (mci->update_2g5g) {
- if (mci->is_2g) {
- ar9003_mci_send_2g5g_status(ah, true);
- ar9003_mci_send_lna_transfer(ah, true);
- udelay(5);
+ if (!mci->update_2g5g)
+ return;
- REG_CLR_BIT(ah, AR_MCI_TX_CTRL,
- AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE);
- REG_CLR_BIT(ah, AR_PHY_GLB_CONTROL,
- AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL);
+ if (mci->is_2g) {
+ ar9003_mci_send_2g5g_status(ah, true);
+ ar9003_mci_send_lna_transfer(ah, true);
+ udelay(5);
- if (!(mci->config & ATH_MCI_CONFIG_DISABLE_OSLA)) {
- REG_SET_BIT(ah, AR_BTCOEX_CTRL,
- AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN);
- }
- } else {
- ar9003_mci_send_lna_take(ah, true);
- udelay(5);
-
- REG_SET_BIT(ah, AR_MCI_TX_CTRL,
- AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE);
- REG_SET_BIT(ah, AR_PHY_GLB_CONTROL,
- AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL);
- REG_CLR_BIT(ah, AR_BTCOEX_CTRL,
+ REG_CLR_BIT(ah, AR_MCI_TX_CTRL,
+ AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE);
+ REG_CLR_BIT(ah, AR_PHY_GLB_CONTROL,
+ AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL);
+
+ if (!(mci->config & ATH_MCI_CONFIG_DISABLE_OSLA))
+ REG_SET_BIT(ah, AR_BTCOEX_CTRL,
AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN);
+ } else {
+ ar9003_mci_send_lna_take(ah, true);
+ udelay(5);
- ar9003_mci_send_2g5g_status(ah, true);
- }
+ REG_SET_BIT(ah, AR_MCI_TX_CTRL,
+ AR_MCI_TX_CTRL_DISABLE_LNA_UPDATE);
+ REG_SET_BIT(ah, AR_PHY_GLB_CONTROL,
+ AR_BTCOEX_CTRL_BT_OWN_SPDT_CTRL);
+ REG_CLR_BIT(ah, AR_BTCOEX_CTRL,
+ AR_BTCOEX_CTRL_ONE_STEP_LOOK_AHEAD_EN);
+
+ ar9003_mci_send_2g5g_status(ah, true);
}
}
@@ -1258,12 +1255,12 @@ u32 ar9003_mci_state(struct ath_hw *ah, u32 state_type, u32 *p_data)
}
if (p_data)
*p_data = more_gpm;
- }
+ }
- if (value != MCI_GPM_INVALID)
- value <<= 4;
+ if (value != MCI_GPM_INVALID)
+ value <<= 4;
- break;
+ break;
case MCI_STATE_LAST_SCHD_MSG_OFFSET:
value = MS(REG_READ(ah, AR_MCI_RX_STATUS),
AR_MCI_RX_LAST_SCHD_MSG_INDEX);
@@ -1358,24 +1355,22 @@ u32 ar9003_mci_state(struct ath_hw *ah, u32 state_type, u32 *p_data)
ar9003_mci_send_coex_bt_status_query(ah, true, query_type);
break;
case MCI_STATE_NEED_FLUSH_BT_INFO:
- /*
- * btcoex_hw.mci.unhalt_bt_gpm means whether it's
- * needed to send UNHALT message. It's set whenever
- * there's a request to send HALT message.
- * mci_halted_bt_gpm means whether HALT message is sent
- * out successfully.
- *
- * Checking (mci_unhalt_bt_gpm == false) instead of
- * checking (ah->mci_halted_bt_gpm == false) will make
- * sure currently is in UNHALT-ed mode and BT can
- * respond to status query.
- */
- value = (!mci->unhalt_bt_gpm &&
- mci->need_flush_btinfo) ? 1 : 0;
- if (p_data)
- mci->need_flush_btinfo =
- (*p_data != 0) ? true : false;
- break;
+ /*
+ * btcoex_hw.mci.unhalt_bt_gpm means whether it's
+ * needed to send UNHALT message. It's set whenever
+ * there's a request to send HALT message.
+ * mci_halted_bt_gpm means whether HALT message is sent
+ * out successfully.
+ *
+ * Checking (mci_unhalt_bt_gpm == false) instead of
+ * checking (ah->mci_halted_bt_gpm == false) will make
+ * sure currently is in UNHALT-ed mode and BT can
+ * respond to status query.
+ */
+ value = (!mci->unhalt_bt_gpm && mci->need_flush_btinfo) ? 1 : 0;
+ if (p_data)
+ mci->need_flush_btinfo = (*p_data != 0) ? true : false;
+ break;
case MCI_STATE_RECOVER_RX:
ar9003_mci_prep_interface(ah);
mci->query_bt = true;
--
1.7.10.2
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2012-05-24 4:04 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-05-24 4:03 [PATCH v2 13/22] ath9k: cleanup MCI indentation Sujith Manoharan
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.