All of lore.kernel.org
 help / color / mirror / Atom feed
* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
@ 2013-12-17 18:26 Oleksij Rempel
  2013-12-19  3:14 ` Sujith Manoharan
  0 siblings, 1 reply; 14+ messages in thread
From: Oleksij Rempel @ 2013-12-17 18:26 UTC (permalink / raw)
  To: ath9k-devel

Hello all,

my kernel log spammed with this message:
ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit

Hardware:
02:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network
Adapter (rev 01)
	Subsystem: Foxconn International, Inc. Device e052
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at f7c00000 (64-bit, non-prefetchable) [size=512K]
	Expansion ROM@f7c80000 [disabled] [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: ath9k

According to the source it looks like a bug:
        /*
         * No valid hardware bitrate found -- we should not get here
         * because hardware has already validated this frame as OK.
         */
        ath_dbg(common, ANY,
                "unsupported hw bitrate detected 0x%02x using 1 Mbit\n",
                rx_stats->rs_rate);
        RX_STAT_INC(rx_rate_err);

-- 
Regards,
Oleksij

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2013-12-17 18:26 [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit Oleksij Rempel
@ 2013-12-19  3:14 ` Sujith Manoharan
  2013-12-19  7:33   ` Oleksij Rempel
  0 siblings, 1 reply; 14+ messages in thread
From: Sujith Manoharan @ 2013-12-19  3:14 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> Hello all,
> 
> my kernel log spammed with this message:
> ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit

Does this happen a lot ?

Sujith

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2013-12-19  3:14 ` Sujith Manoharan
@ 2013-12-19  7:33   ` Oleksij Rempel
  2014-01-07 16:26     ` Sujith Manoharan
  0 siblings, 1 reply; 14+ messages in thread
From: Oleksij Rempel @ 2013-12-19  7:33 UTC (permalink / raw)
  To: ath9k-devel

Am 19.12.2013 04:14, schrieb Sujith Manoharan:
> Oleksij Rempel wrote:
>> Hello all,
>>
>> my kernel log spammed with this message:
>> ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
> 
> Does this happen a lot ?

It depends on how intensively WiFi is used.

See attachment

-- 
Regards,
Oleksij
-------------- next part --------------
[  657.383048] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  657.703201] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  658.023359] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  658.343496] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  658.663641] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  658.983827] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  659.303934] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  659.624084] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  659.944247] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  660.264380] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  660.584529] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  660.904671] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  661.224856] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  773.916747] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  774.236930] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  774.557067] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  774.877201] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  775.197345] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  775.517481] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  775.837638] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  776.157769] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  776.477964] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  776.798090] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  777.118227] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  777.438373] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  778.078689] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  778.398722] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  778.718882] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  779.039120] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  779.359244] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  779.679402] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  779.999573] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  780.319713] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  780.639879] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  780.960013] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[  781.280047] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 5144.458380] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6266.485983] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6266.806103] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6267.126300] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6267.446403] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6267.766558] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6268.086721] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6268.406846] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6268.727002] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6269.047159] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6269.367295] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6269.687494] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6270.007626] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6270.327740] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6270.647901] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6270.968076] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6271.288211] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6271.608384] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6271.928514] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6272.248645] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6506.596660] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6506.916865] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6507.248066] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6507.568108] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6507.888245] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6508.528535] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6508.848698] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6509.488992] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6509.809142] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6510.129235] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6510.449426] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6510.769584] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6511.089656] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6511.409874] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6511.730079] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6512.050138] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6512.370288] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6626.652975] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6626.973101] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6627.627405] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6627.947552] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6628.267698] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6628.587878] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6628.908074] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6629.228125] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6629.548337] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6629.868454] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6630.188585] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6630.508760] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6630.828908] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6631.149028] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6631.469202] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6631.789363] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6632.109473] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6632.429643] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6746.707320] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6747.027557] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6747.347617] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6747.667796] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6747.987955] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6748.308032] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6748.628174] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6749.588614] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6750.228965] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6750.549090] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6750.869251] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6751.509518] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6752.149796] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6752.469898] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6866.762660] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6867.082810] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6867.402983] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6867.723070] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6868.043246] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6868.363367] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6868.683508] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6869.003657] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6869.323811] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6869.643964] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6869.964108] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6870.284252] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6870.924516] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6871.244732] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6871.564866] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6872.205129] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6872.525278] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6987.138175] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6987.458280] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6988.098583] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6988.418716] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6988.738872] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6989.059074] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6989.379161] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6989.699329] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6990.019460] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6990.339578] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6990.659730] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6990.979883] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6991.300050] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6991.620179] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6992.260464] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 6992.580611] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7106.873313] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7107.193505] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7107.513624] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7108.154909] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7108.475025] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7108.795152] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7109.115327] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7109.435478] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7110.075810] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7110.395947] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7110.716088] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7111.036238] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7111.676539] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7111.996687] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7112.316836] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7112.636963] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7226.928657] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7227.248786] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7227.568954] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7227.889051] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7228.529396] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7228.849545] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7229.489840] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7229.809977] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7230.130115] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7230.450304] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7230.770419] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7231.410694] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7231.730867] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7232.371223] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7232.691241] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7346.983967] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7347.304157] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7347.624290] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7347.944435] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7348.584722] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7349.545123] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7350.185514] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7350.505647] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7350.825771] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7351.145939] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7351.466037] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7351.786197] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7352.106324] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7352.426492] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7352.746610] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7467.359454] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7467.679586] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7467.999730] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7468.319883] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7468.640031] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7468.960206] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7469.280366] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7469.600545] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7469.920656] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7470.240791] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7470.560928] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7470.881095] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7471.201242] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7471.521387] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7471.841522] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7472.161650] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7472.481802] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 7472.801950] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[23608.259628] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[24568.431216] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[26250.283323] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[26369.736390] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
[27210.516827] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2013-12-19  7:33   ` Oleksij Rempel
@ 2014-01-07 16:26     ` Sujith Manoharan
  2014-01-07 20:50       ` Oleksij Rempel
  0 siblings, 1 reply; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-07 16:26 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> > Does this happen a lot ?
> 
> It depends on how intensively WiFi is used.
> 
> See attachment
> 
> [  657.383048] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
> [  657.703201] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit

Can you load the driver with debug=0x200 (with latest wireless-testing) and
post the kernel log when the issue happens ?

Sujith

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-07 16:26     ` Sujith Manoharan
@ 2014-01-07 20:50       ` Oleksij Rempel
  2014-01-08  2:08         ` Sujith Manoharan
  2014-01-08  2:20         ` Sujith Manoharan
  0 siblings, 2 replies; 14+ messages in thread
From: Oleksij Rempel @ 2014-01-07 20:50 UTC (permalink / raw)
  To: ath9k-devel

Am 07.01.2014 17:26, schrieb Sujith Manoharan:
> Oleksij Rempel wrote:
>>> Does this happen a lot ?
>>
>> It depends on how intensively WiFi is used.
>>
>> See attachment
>>
>> [  657.383048] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
>> [  657.703201] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
> 
> Can you load the driver with debug=0x200 (with latest wireless-testing) and
> post the kernel log when the issue happens ?

looks like happens at scan time:
[ 3161.475583] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 3161.540259] ath: phy3: Set channel: 5180 MHz width: 2
[ 3161.540394] ath: phy3: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 3161.540414] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3161.744603] ath: phy3: Set channel: 2447 MHz width: 0
[ 3161.744748] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1

some time there are some BB_WATCHDOG warning too.
-- 
Regards,
Oleksij
-------------- next part --------------
[    5.577791] rts51x: Close SSC clock power!
[    5.648987] init: isc-dhcp-server main process (2022) terminated with status 1
[    5.649023] init: isc-dhcp-server main process ended, respawning
[    5.782881] init: isc-dhcp-server main process (2112) terminated with status 1
[    5.782908] init: isc-dhcp-server main process ended, respawning
[    5.896407] init: isc-dhcp-server main process (2142) terminated with status 1
[    5.896442] init: isc-dhcp-server main process ended, respawning
[    5.936332] init: isc-dhcp-server main process (2156) terminated with status 1
[    5.936370] init: isc-dhcp-server main process ended, respawning
[    5.969240] init: isc-dhcp-server main process (2165) terminated with status 1
[    5.969266] init: isc-dhcp-server main process ended, respawning
[    6.008114] init: isc-dhcp-server main process (2173) terminated with status 1
[    6.008148] init: isc-dhcp-server main process ended, respawning
[    6.049715] init: isc-dhcp-server main process (2181) terminated with status 1
[    6.049765] init: isc-dhcp-server main process ended, respawning
[    6.095112] init: isc-dhcp-server main process (2201) terminated with status 1
[    6.095142] init: isc-dhcp-server main process ended, respawning
[    6.127084] init: isc-dhcp-server main process (2234) terminated with status 1
[    6.127117] init: isc-dhcp-server main process ended, respawning
[    6.158261] init: isc-dhcp-server main process (2246) terminated with status 1
[    6.158306] init: isc-dhcp-server main process ended, respawning
[    6.205178] init: isc-dhcp-server main process (2254) terminated with status 1
[    6.205212] init: isc-dhcp-server respawning too fast, stopped
[    7.966088] audit_printk_skb: 153 callbacks suppressed
[    7.966094] type=1400 audit(1389124263.375:62): apparmor="DENIED" operation="mkdir" profile="/usr/lib/telepathy/mission-control-5" name="/var/lib/lightdm/.config/libaccounts-glib/" pid=2766 comm="mission-control" requested_mask="c" denied_mask="c" fsuid=110 ouid=110
[    7.969185] type=1400 audit(1389124263.378:63): apparmor="DENIED" operation="open" profile="/usr/lib/telepathy/mission-control-5" name="/var/lib/lightdm/.config/dconf/user" pid=2766 comm="mission-control" requested_mask="r" denied_mask="r" fsuid=110 ouid=110
[    8.021226] type=1400 audit(1389124263.430:64): apparmor="DENIED" operation="mkdir" profile="/usr/lib/telepathy/mission-control-5" name="/var/lib/lightdm/.local/share/telepathy/" pid=2766 comm="mission-control" requested_mask="c" denied_mask="c" fsuid=110 ouid=110
[    8.022570] type=1400 audit(1389124263.431:65): apparmor="DENIED" operation="mkdir" profile="/usr/lib/telepathy/mission-control-5" name="/var/lib/lightdm/.local/share/telepathy/" pid=2766 comm="mission-control" requested_mask="c" denied_mask="c" fsuid=110 ouid=110
[    8.138552] rts51x: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
[    8.138559] rts51x: [rts51x_scsi.c][allow_medium_removal]:[564]
[    8.138643] rts51x: Command (unknown command) (16 bytes)
[    8.138645] rts51x: 
[    8.138646]  85 08
[    8.138649]  0e 00
[    8.138651]  00 00
[    8.138652]  01 00
[    8.138654]  00 00
[    8.138656]  00 00
[    8.138658]  00 40
[    8.138659]  ec 00
[    8.138661] 
[    8.254010] tun: Universal TUN/TAP device driver, 1.6
[    8.254014] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    8.257802] IPv6: ADDRCONF(NETDEV_UP): tap0: link is not ready
[    8.294537] init: plymouth-stop pre-start process (2881) terminated with status 1
[   11.893301] wlan11: authenticate with 90:f6:52:ff:d3:85
[   11.903346] wlan11: send auth to 90:f6:52:ff:d3:85 (try 1/3)
[   11.905651] wlan11: authenticated
[   11.906659] wlan11: associate with 90:f6:52:ff:d3:85 (try 1/3)
[   11.910414] wlan11: RX AssocResp from 90:f6:52:ff:d3:85 (capab=0x431 status=0 aid=4)
[   11.910456] wlan11: associated
[   11.910465] IPv6: ADDRCONF(NETDEV_CHANGE): wlan11: link becomes ready
[   11.910817] cfg80211: Calling CRDA for country: DE
[   11.913357] ath: EEPROM regdomain: 0x8114
[   11.913359] ath: EEPROM indicates we should expect a country code
[   11.913360] ath: doing EEPROM country->regdmn map search
[   11.913362] ath: country maps to regdmn code: 0x37
[   11.913363] ath: Country alpha2 being used: DE
[   11.913364] ath: Regpair used: 0x37
[   11.913365] ath: regdomain 0x8114 dynamically updated by country IE
[   11.913393] cfg80211: Regulatory domain changed to country: DE
[   11.913394] cfg80211:  DFS Master region: unset
[   11.913396] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   11.913397] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   11.913399] cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   11.913400] cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   11.913401] cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[   11.913403] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[   30.016989] ath: phy0: BB_WATCHDOG: Skipping interrupts
[  136.066007] ath: phy0: BB_WATCHDOG: Skipping interrupts
[  202.124425] wlan11: deauthenticating from 90:f6:52:ff:d3:85 by local choice (reason=3)
[  202.145572] cfg80211: Calling CRDA to update world regulatory domain
[  202.150962] cfg80211: World regulatory domain updated:
[  202.150966] cfg80211:  DFS Master region: unset
[  202.150968] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  202.150972] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  202.150974] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  202.150977] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  202.150979] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  202.150981] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  202.157998] ath9k: ath9k: Driver unloaded
[  217.909700] ath: phy1: Eeprom VER: 2, REV: 0
[  217.910976] ath: phy1: TX streams 2, RX streams: 2
[  217.910978] ath: phy1: TX streams 2, RX streams: 2
[  217.910979] ath: EEPROM regdomain: 0x6c
[  217.910980] ath: EEPROM indicates we should expect a direct regpair map
[  217.910982] ath: Country alpha2 being used: 00
[  217.910983] ath: Regpair used: 0x6c
[  217.910988] ath: phy1: tx DMA: 512 buffers 1 desc/buf
[  217.910996] ath: phy1: tx DMA map: ffff880090f50000 (65536) -> 90f50000 (65536)
[  217.911008] ath: phy1: beacon DMA: 8 buffers 1 desc/buf
[  217.911011] ath: phy1: beacon DMA map: ffff880090eb2000 (1024) -> 90eb2000 (1024)
[  217.911509] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[  217.911958] ieee80211 phy1: Atheros AR9462 Rev:2 mem=0xffffc9000cc80000, irq=17
[  217.920369] systemd-udevd[4296]: renamed network interface wlan0 to wlan11
[  217.921970] ath: phy1: Starting driver with initial channel: 2412 MHz
[  217.927890] ath: phy1: Attach a VIF of type: 2
[  217.927937] ath: phy1: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  217.927945] ath: phy1: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  217.927952] ath: phy1: Configure tx [queue/halq] [2/2], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  217.927958] ath: phy1: Configure tx [queue/halq] [3/3], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  217.927968] ath: phy1: Monitor mode is disabled
[  217.927970] ath: phy1: Set channel: 2412 MHz width: 0
[  217.928147] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 0
[  217.934106] ath: phy1: Set power: 16
[  217.934155] ath: phy1: Set HW RX filter: 0x207
[  217.934163] ath: phy1: Set HW RX filter: 0x207
[  217.934224] IPv6: ADDRCONF(NETDEV_UP): wlan11: link is not ready
[  217.934228] ath: phy1: Set HW RX filter: 0x207
[  217.952751] ath: phy1: Set HW RX filter: 0x17
[  217.952762] ath: phy1: Set channel: 2412 MHz width: 0
[  217.952903] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 0
[  218.016824] ath: phy1: Set channel: 2417 MHz width: 0
[  218.016970] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[  218.017889] ath: phy1: Set power: 17
[  218.077850] ath: phy1: Set channel: 2422 MHz width: 0
[  218.077999] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[  218.138935] ath: phy1: Set channel: 2427 MHz width: 0
[  218.139083] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[  218.199879] ath: phy1: Set channel: 2432 MHz width: 0
[  218.200035] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[  218.260942] ath: phy1: Set channel: 2437 MHz width: 0
[  218.261090] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[  218.321964] ath: phy1: Set channel: 2442 MHz width: 0
[  218.322110] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[  218.383026] ath: phy1: Set channel: 2447 MHz width: 0
[  218.383178] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[  218.444037] ath: phy1: Set channel: 2452 MHz width: 0
[  218.444187] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[  218.505047] ath: phy1: Set channel: 2457 MHz width: 0
[  218.505197] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[  218.506167] ath: phy1: Set power: 16
[  218.566085] ath: phy1: Set channel: 2462 MHz width: 0
[  218.566223] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[  218.567196] ath: phy1: Set power: 17
[  218.627124] ath: phy1: Set channel: 2467 MHz width: 0
[  218.627292] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[  218.739158] ath: phy1: Set channel: 2472 MHz width: 0
[  218.739305] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[  218.740319] ath: phy1: Set power: 16
[  218.851212] ath: phy1: Set channel: 5180 MHz width: 0
[  218.851369] ath: phy1: Reset to 5180 MHz, HT40: 0 fastcc: 1
[  218.856388] ath: phy1: Set power: 15
[  218.967275] ath: phy1: Set channel: 5200 MHz width: 0
[  218.967442] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[  219.079286] ath: phy1: Set channel: 5220 MHz width: 0
[  219.079423] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[  219.191342] ath: phy1: Set channel: 5240 MHz width: 0
[  219.191475] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[  219.303394] ath: phy1: Set channel: 5260 MHz width: 0
[  219.303531] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[  219.304443] ath: phy1: Set power: 17
[  219.415439] ath: phy1: Set channel: 5280 MHz width: 0
[  219.415580] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[  219.416505] ath: phy1: Set power: 15
[  219.527448] ath: phy1: Set channel: 5300 MHz width: 0
[  219.527590] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[  219.639552] ath: phy1: Set channel: 5320 MHz width: 0
[  219.639683] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[  219.751601] ath: phy1: Set channel: 5500 MHz width: 0
[  219.751739] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[  219.752654] ath: phy1: Set power: 16
[  219.863639] ath: phy1: Set channel: 5520 MHz width: 0
[  219.863787] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[  219.864807] ath: phy1: Set power: 17
[  219.975736] ath: phy1: Set channel: 5540 MHz width: 0
[  219.975880] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[  220.087779] ath: phy1: Set channel: 5560 MHz width: 0
[  220.087927] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[  220.199838] ath: phy1: Set channel: 5580 MHz width: 0
[  220.199977] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[  220.311889] ath: phy1: Set channel: 5600 MHz width: 0
[  220.312026] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[  220.423914] ath: phy1: Set channel: 5620 MHz width: 0
[  220.424051] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[  220.535993] ath: phy1: Set channel: 5640 MHz width: 0
[  220.536130] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[  220.648063] ath: phy1: Set channel: 5660 MHz width: 0
[  220.648207] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[  220.760088] ath: phy1: Set channel: 5680 MHz width: 0
[  220.760245] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[  220.872132] ath: phy1: Set channel: 5700 MHz width: 0
[  220.872279] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[  220.873194] ath: phy1: Set power: 16
[  220.984201] ath: phy1: Set channel: 5745 MHz width: 0
[  220.984337] ath: phy1: Reset to 5745 MHz, HT40: 0 fastcc: 1
[  220.985257] ath: phy1: Set power: 17
[  221.096247] ath: phy1: Set channel: 5765 MHz width: 0
[  221.096384] ath: phy1: Reset to 5765 MHz, HT40: 0 fastcc: 1
[  221.208302] ath: phy1: Set channel: 5785 MHz width: 0
[  221.208438] ath: phy1: Reset to 5785 MHz, HT40: 0 fastcc: 1
[  221.320360] ath: phy1: Set channel: 5805 MHz width: 0
[  221.320500] ath: phy1: Reset to 5805 MHz, HT40: 0 fastcc: 1
[  221.432406] ath: phy1: Set channel: 5825 MHz width: 0
[  221.432540] ath: phy1: Reset to 5825 MHz, HT40: 0 fastcc: 1
[  221.544470] ath: phy1: Set channel: 2412 MHz width: 0
[  221.544613] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 0
[  221.548695] ath: phy1: Set power: 16
[  221.548730] ath: phy1: Set HW RX filter: 0x207
[  221.582107] ath: phy1: Set HW RX filter: 0x17
[  221.582119] ath: phy1: Set channel: 2412 MHz width: 0
[  221.582267] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 0
[  221.646515] ath: phy1: Set channel: 2417 MHz width: 0
[  221.646677] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[  221.647599] ath: phy1: Set power: 17
[  221.707481] ath: phy1: Set channel: 2422 MHz width: 0
[  221.707653] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[  221.768572] ath: phy1: Set channel: 2427 MHz width: 0
[  221.768710] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[  221.829589] ath: phy1: Set channel: 2432 MHz width: 0
[  221.829728] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[  221.890653] ath: phy1: Set channel: 2437 MHz width: 0
[  221.890809] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[  221.951600] ath: phy1: Set channel: 2442 MHz width: 0
[  221.951743] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[  222.012613] ath: phy1: Set channel: 2447 MHz width: 0
[  222.012757] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[  222.073673] ath: phy1: Set channel: 2452 MHz width: 0
[  222.073808] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[  222.134695] ath: phy1: Set channel: 2457 MHz width: 0
[  222.134827] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[  222.135790] ath: phy1: Set power: 16
[  222.195700] ath: phy1: Set channel: 2462 MHz width: 0
[  222.195839] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[  222.196834] ath: phy1: Set power: 17
[  222.256764] ath: phy1: Set channel: 2467 MHz width: 0
[  222.256914] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[  222.368815] ath: phy1: Set channel: 2472 MHz width: 0
[  222.368971] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[  222.369964] ath: phy1: Set power: 16
[  222.480864] ath: phy1: Set channel: 5180 MHz width: 0
[  222.480999] ath: phy1: Reset to 5180 MHz, HT40: 0 fastcc: 1
[  222.485970] ath: phy1: Set power: 15
[  222.545933] ath: phy1: Set channel: 5200 MHz width: 0
[  222.546070] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[  222.657959] ath: phy1: Set channel: 5220 MHz width: 0
[  222.658104] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[  222.770001] ath: phy1: Set channel: 5240 MHz width: 0
[  222.770139] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[  222.882029] ath: phy1: Set channel: 5260 MHz width: 0
[  222.882172] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[  222.883103] ath: phy1: Set power: 17
[  222.994099] ath: phy1: Set channel: 5280 MHz width: 0
[  222.994246] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[  222.995184] ath: phy1: Set power: 15
[  223.106155] ath: phy1: Set channel: 5300 MHz width: 0
[  223.106306] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[  223.218222] ath: phy1: Set channel: 5320 MHz width: 0
[  223.218354] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[  223.330262] ath: phy1: Set channel: 5500 MHz width: 0
[  223.330402] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[  223.331343] ath: phy1: Set power: 16
[  223.442269] ath: phy1: Set channel: 5520 MHz width: 0
[  223.442430] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[  223.443401] ath: phy1: Set power: 17
[  223.554358] ath: phy1: Set channel: 5540 MHz width: 0
[  223.554491] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[  223.666410] ath: phy1: Set channel: 5560 MHz width: 0
[  223.666534] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[  223.778459] ath: phy1: Set channel: 5580 MHz width: 0
[  223.778605] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[  223.890513] ath: phy1: Set channel: 5600 MHz width: 0
[  223.890649] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[  224.002561] ath: phy1: Set channel: 5620 MHz width: 0
[  224.002694] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[  224.114610] ath: phy1: Set channel: 5640 MHz width: 0
[  224.114752] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[  224.226625] ath: phy1: Set channel: 5660 MHz width: 0
[  224.226767] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[  224.338722] ath: phy1: Set channel: 5680 MHz width: 0
[  224.338871] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[  224.450773] ath: phy1: Set channel: 5700 MHz width: 0
[  224.450909] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[  224.451818] ath: phy1: Set power: 16
[  224.562822] ath: phy1: Set channel: 5745 MHz width: 0
[  224.562949] ath: phy1: Reset to 5745 MHz, HT40: 0 fastcc: 1
[  224.563860] ath: phy1: Set power: 17
[  224.674875] ath: phy1: Set channel: 5765 MHz width: 0
[  224.675014] ath: phy1: Reset to 5765 MHz, HT40: 0 fastcc: 1
[  224.786905] ath: phy1: Set channel: 5785 MHz width: 0
[  224.787063] ath: phy1: Reset to 5785 MHz, HT40: 0 fastcc: 1
[  224.898984] ath: phy1: Set channel: 5805 MHz width: 0
[  224.899117] ath: phy1: Reset to 5805 MHz, HT40: 0 fastcc: 1
[  225.011029] ath: phy1: Set channel: 5825 MHz width: 0
[  225.011160] ath: phy1: Reset to 5825 MHz, HT40: 0 fastcc: 1
[  225.123083] ath: phy1: Set channel: 2412 MHz width: 0
[  225.123218] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 0
[  225.123476] wlan11: authenticate with 90:f6:52:ff:d3:86
[  225.127328] ath: phy1: Set power: 16
[  225.127367] ath: phy1: Set HW RX filter: 0x207
[  225.127397] ath: phy1: Set channel: 5180 MHz width: 2
[  225.127532] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  225.133828] ath: phy1: Set power: 15
[  225.133938] wlan11: send auth to 90:f6:52:ff:d3:86 (try 1/3)
[  225.135474] wlan11: authenticated
[  225.136141] wlan11: associate with 90:f6:52:ff:d3:86 (try 1/3)
[  225.138097] wlan11: RX AssocResp from 90:f6:52:ff:d3:86 (capab=0x11 status=0 aid=1)
[  225.138111] ath: phy1: Configure tx [queue/halq] [2/2], aifs: 3, cw_min: 15, cw_max: 1023, txop: 0
[  225.138117] ath: phy1: Configure tx [queue/halq] [3/3], aifs: 7, cw_min: 15, cw_max: 1023, txop: 0
[  225.138121] ath: phy1: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 7, cw_max: 15, txop: 94
[  225.138125] ath: phy1: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 3, cw_max: 7, txop: 47
[  225.138130] ath: phy1: BSSID 90:f6:52:ff:d3:86 Changed ASSOC 1
[  225.138132] ath: phy1: Primary Station interface: 68:94:23:16:16:75, BSSID: 90:f6:52:ff:d3:86
[  225.138157] wlan11: associated
[  225.138167] IPv6: ADDRCONF(NETDEV_CHANGE): wlan11: link becomes ready
[  225.138949] cfg80211: Calling CRDA for country: DE
[  225.138978] ath: phy1: Set HW RX filter: 0x607
[  225.141737] ath: EEPROM regdomain: 0x8114
[  225.141740] ath: EEPROM indicates we should expect a country code
[  225.141741] ath: doing EEPROM country->regdmn map search
[  225.141742] ath: country maps to regdmn code: 0x37
[  225.141744] ath: Country alpha2 being used: DE
[  225.141745] ath: Regpair used: 0x37
[  225.141746] ath: regdomain 0x8114 dynamically updated by country IE
[  225.141774] cfg80211: Regulatory domain changed to country: DE
[  225.141775] cfg80211:  DFS Master region: unset
[  225.141777] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  225.141780] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  225.141782] cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  225.141783] cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  225.141785] cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[  225.141788] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[  225.144843] ath: phy1: Set HW Key
[  225.144930] ath: phy1: Set HW Key
[  225.149577] ath: phy1: Set HW RX filter: 0x607
[  225.180937] ath: phy1: Set HW RX filter: 0x607
[  226.648100] ath: phy1: Set HW RX filter: 0x607
[  241.138012] ath: phy1: Set HW RX filter: 0x417
[  241.138044] ath: phy1: Set channel: 2412 MHz width: 0
[  241.138188] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[  241.202526] ath: phy1: Set channel: 2417 MHz width: 0
[  241.202678] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[  241.263575] ath: phy1: Set channel: 5180 MHz width: 2
[  241.263732] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  241.467950] ath: phy1: Set channel: 2422 MHz width: 0
[  241.468117] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[  241.532688] ath: phy1: Set channel: 2427 MHz width: 0
[  241.532869] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[  241.593719] ath: phy1: Set channel: 5180 MHz width: 2
[  241.593864] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  241.798084] ath: phy1: Set channel: 2432 MHz width: 0
[  241.798227] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[  241.862835] ath: phy1: Set channel: 2437 MHz width: 0
[  241.862988] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[  241.923892] ath: phy1: Set channel: 5180 MHz width: 2
[  241.924053] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  242.128233] ath: phy1: Set channel: 2442 MHz width: 0
[  242.128375] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[  242.192985] ath: phy1: Set channel: 2447 MHz width: 0
[  242.193126] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[  242.253966] ath: phy1: Set channel: 5180 MHz width: 2
[  242.254120] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  242.458361] ath: phy1: Set channel: 2452 MHz width: 0
[  242.458516] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[  242.523100] ath: phy1: Set channel: 2457 MHz width: 0
[  242.523238] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[  242.584177] ath: phy1: Set channel: 5180 MHz width: 2
[  242.584335] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  242.788617] ath: phy1: Set channel: 2462 MHz width: 0
[  242.788759] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[  242.853305] ath: phy1: Set channel: 5180 MHz width: 2
[  242.853469] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  243.057720] ath: phy1: Set channel: 2467 MHz width: 0
[  243.057874] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[  243.173450] ath: phy1: Set channel: 5180 MHz width: 2
[  243.173600] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  243.377866] ath: phy1: Set channel: 2472 MHz width: 0
[  243.378025] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[  243.432769] ath: phy1: BB_WATCHDOG: Skipping interrupts
[  243.432965] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 0
[  243.493597] ath: phy1: Set channel: 5180 MHz width: 2
[  243.493752] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  243.698009] ath: phy1: Set channel: 5180 MHz width: 2
[  243.698153] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  243.813744] ath: phy1: Set channel: 5180 MHz width: 2
[  243.813901] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  244.018107] ath: phy1: Set channel: 5200 MHz width: 0
[  244.018272] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[  244.133893] ath: phy1: Set channel: 5180 MHz width: 2
[  244.134039] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  244.338270] ath: phy1: Set channel: 5220 MHz width: 0
[  244.338433] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[  244.454031] ath: phy1: Set channel: 5180 MHz width: 2
[  244.454172] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  244.658424] ath: phy1: Set channel: 5240 MHz width: 0
[  244.658591] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[  244.774165] ath: phy1: Set channel: 5180 MHz width: 2
[  244.774326] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  244.978509] ath: phy1: Set channel: 5260 MHz width: 0
[  244.978651] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[  245.094291] ath: phy1: Set channel: 5180 MHz width: 2
[  245.094434] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  245.298699] ath: phy1: Set channel: 5280 MHz width: 0
[  245.298846] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[  245.414397] ath: phy1: Set channel: 5180 MHz width: 2
[  245.414544] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  245.618862] ath: phy1: Set channel: 5300 MHz width: 0
[  245.619007] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[  245.734583] ath: phy1: Set channel: 5180 MHz width: 2
[  245.734723] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  245.938921] ath: phy1: Set channel: 5320 MHz width: 0
[  245.939066] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[  246.054749] ath: phy1: Set channel: 5180 MHz width: 2
[  246.054910] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  246.259159] ath: phy1: Set channel: 5500 MHz width: 0
[  246.259319] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[  246.374928] ath: phy1: Set channel: 5180 MHz width: 2
[  246.375084] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  246.579309] ath: phy1: Set channel: 5520 MHz width: 0
[  246.579466] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[  246.695079] ath: phy1: Set channel: 5180 MHz width: 2
[  246.695244] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  246.899397] ath: phy1: Set channel: 5540 MHz width: 0
[  246.899552] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[  247.015218] ath: phy1: Set channel: 5180 MHz width: 2
[  247.015371] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  247.219624] ath: phy1: Set channel: 5560 MHz width: 0
[  247.219804] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[  247.335346] ath: phy1: Set channel: 5180 MHz width: 2
[  247.335503] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  247.539601] ath: phy1: Set channel: 5580 MHz width: 0
[  247.539735] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[  247.655451] ath: phy1: Set channel: 5180 MHz width: 2
[  247.655601] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  247.859790] ath: phy1: Set channel: 5600 MHz width: 0
[  247.859951] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[  247.975656] ath: phy1: Set channel: 5180 MHz width: 2
[  247.975797] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  248.179992] ath: phy1: Set channel: 5620 MHz width: 0
[  248.180162] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[  248.295817] ath: phy1: Set channel: 5180 MHz width: 2
[  248.296009] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  248.499983] ath: phy1: Set channel: 5640 MHz width: 0
[  248.500124] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[  248.615870] ath: phy1: Set channel: 5180 MHz width: 2
[  248.616012] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  248.820256] ath: phy1: Set channel: 5660 MHz width: 0
[  248.820393] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[  248.936050] ath: phy1: Set channel: 5180 MHz width: 2
[  248.936199] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  249.140438] ath: phy1: Set channel: 5680 MHz width: 0
[  249.140622] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[  249.256222] ath: phy1: Set channel: 5180 MHz width: 2
[  249.256367] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  249.460619] ath: phy1: Set channel: 5700 MHz width: 0
[  249.460770] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[  249.576374] ath: phy1: Set channel: 5180 MHz width: 2
[  249.576533] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[  249.581071] ath: phy1: Set HW RX filter: 0x607
[  251.586540] ath: phy1: Set HW RX filter: 0x607
[  252.904859] ath: phy1: Set HW RX filter: 0x607
[  264.713437] wlan11: deauthenticating from 90:f6:52:ff:d3:86 by local choice (reason=3)
[  264.713812] ath: phy1: Set HW Key
[  264.713883] ath: phy1: BSSID 00:00:00:00:00:00 Changed ASSOC 0
[  264.713900] ath: phy1: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  264.713906] ath: phy1: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  264.713910] ath: phy1: Configure tx [queue/halq] [2/2], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  264.713914] ath: phy1: Configure tx [queue/halq] [3/3], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[  264.713920] ath: phy1: Set channel: 5180 MHz width: 0
[  264.714035] ath: phy1: Reset to 5180 MHz, HT40: 0 fastcc: 0
[  264.719939] ath: phy1: Set power: 20
[  264.719973] ath: phy1: Set HW Key
[  264.720022] ath: phy1: Detach Interface
[  264.724338] ath: phy1: Driver halt
[  264.737740] cfg80211: Calling CRDA to update world regulatory domain
[  264.745454] cfg80211: World regulatory domain updated:
[  264.745458] cfg80211:  DFS Master region: unset
[  264.745460] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  264.745463] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  264.745466] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  264.745468] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  264.745470] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  264.745472] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  264.745843] ath9k: ath9k: Driver unloaded
[  268.882171] ath: EEPROM regdomain: 0x6c
[  268.882176] ath: EEPROM indicates we should expect a direct regpair map
[  268.882179] ath: Country alpha2 being used: 00
[  268.882181] ath: Regpair used: 0x6c
[  268.882866] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[  268.883417] ieee80211 phy2: Atheros AR9462 Rev:2 mem=0xffffc9000d280000, irq=17
[  268.893536] systemd-udevd[4573]: renamed network interface wlan0 to wlan11
[  268.906737] IPv6: ADDRCONF(NETDEV_UP): wlan11: link is not ready
[  276.109063] wlan11: authenticate with 90:f6:52:ff:d3:85
[  276.119326] wlan11: send auth to 90:f6:52:ff:d3:85 (try 1/3)
[  276.121655] wlan11: authenticated
[  276.122612] wlan11: associate with 90:f6:52:ff:d3:85 (try 1/3)
[  276.127838] wlan11: RX AssocResp from 90:f6:52:ff:d3:85 (capab=0x431 status=0 aid=4)
[  276.127879] wlan11: associated
[  276.127888] IPv6: ADDRCONF(NETDEV_CHANGE): wlan11: link becomes ready
[  276.128186] cfg80211: Calling CRDA for country: DE
[  276.130712] ath: EEPROM regdomain: 0x8114
[  276.130714] ath: EEPROM indicates we should expect a country code
[  276.130716] ath: doing EEPROM country->regdmn map search
[  276.130717] ath: country maps to regdmn code: 0x37
[  276.130718] ath: Country alpha2 being used: DE
[  276.130719] ath: Regpair used: 0x37
[  276.130721] ath: regdomain 0x8114 dynamically updated by country IE
[  276.130749] cfg80211: Regulatory domain changed to country: DE
[  276.130750] cfg80211:  DFS Master region: unset
[  276.130751] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  276.130753] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  276.130754] cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  276.130755] cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  276.130757] cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[  276.130758] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[  401.816157] ath: phy2: BB_WATCHDOG: Skipping interrupts
[  561.465789] wlan11: deauthenticating from 90:f6:52:ff:d3:85 by local choice (reason=3)
[  561.536076] cfg80211: Calling CRDA to update world regulatory domain
[  561.540463] cfg80211: World regulatory domain updated:
[  561.540467] cfg80211:  DFS Master region: unset
[  561.540469] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  561.540471] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  561.540473] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  561.540474] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  561.540476] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  561.540477] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  565.179463] wlan11: authenticate with 90:f6:52:ff:d3:86
[  565.189841] wlan11: direct probe to 90:f6:52:ff:d3:86 (try 1/3)
[  565.390086] wlan11: send auth to 90:f6:52:ff:d3:86 (try 2/3)
[  565.391888] wlan11: authenticated
[  565.393092] wlan11: associate with 90:f6:52:ff:d3:86 (try 1/3)
[  565.395502] wlan11: RX AssocResp from 90:f6:52:ff:d3:86 (capab=0x11 status=0 aid=1)
[  565.395545] wlan11: associated
[  565.395596] cfg80211: Calling CRDA for country: DE
[  565.398250] ath: EEPROM regdomain: 0x8114
[  565.398253] ath: EEPROM indicates we should expect a country code
[  565.398254] ath: doing EEPROM country->regdmn map search
[  565.398255] ath: country maps to regdmn code: 0x37
[  565.398256] ath: Country alpha2 being used: DE
[  565.398257] ath: Regpair used: 0x37
[  565.398259] ath: regdomain 0x8114 dynamically updated by country IE
[  565.398286] cfg80211: Regulatory domain changed to country: DE
[  565.398287] cfg80211:  DFS Master region: unset
[  565.398288] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  565.398290] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  565.398292] cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  565.398293] cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  565.398294] cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[  565.398296] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 1362.632928] ath: phy2: BB_WATCHDOG: Skipping interrupts
[ 1602.740870] ath: phy2: BB_WATCHDOG: Skipping interrupts
[ 1722.799334] ath: phy2: BB_WATCHDOG: Skipping interrupts
[ 1961.990793] ath: phy2: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 2083.285649] ath: phy2: BB_WATCHDOG: Skipping interrupts
[ 2443.131721] ath: phy2: BB_WATCHDOG: Skipping interrupts
[ 2502.610187] wlan11: deauthenticating from 90:f6:52:ff:d3:86 by local choice (reason=3)
[ 2502.631553] cfg80211: Calling CRDA to update world regulatory domain
[ 2502.638679] ath9k: ath9k: Driver unloaded
[ 2502.639409] cfg80211: World regulatory domain updated:
[ 2502.639413] cfg80211:  DFS Master region: unset
[ 2502.639414] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2502.639417] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2502.639419] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2502.639422] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2502.639424] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2502.639426] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2510.156471] ath: phy3: Eeprom VER: 2, REV: 0
[ 2510.157788] ath: phy3: TX streams 2, RX streams: 2
[ 2510.157789] ath: phy3: TX streams 2, RX streams: 2
[ 2510.157791] ath: EEPROM regdomain: 0x6c
[ 2510.157792] ath: EEPROM indicates we should expect a direct regpair map
[ 2510.157794] ath: Country alpha2 being used: 00
[ 2510.157795] ath: Regpair used: 0x6c
[ 2510.157799] ath: phy3: tx DMA: 512 buffers 1 desc/buf
[ 2510.157807] ath: phy3: tx DMA map: ffff880092ba0000 (65536) -> 92ba0000 (65536)
[ 2510.157819] ath: phy3: beacon DMA: 8 buffers 1 desc/buf
[ 2510.157821] ath: phy3: beacon DMA map: ffff88009295b000 (1024) -> 9295b000 (1024)
[ 2510.158331] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht'
[ 2510.158796] ieee80211 phy3: Atheros AR9462 Rev:2 mem=0xffffc9000d900000, irq=17
[ 2510.173827] systemd-udevd[5268]: renamed network interface wlan0 to wlan11
[ 2510.175071] ath: phy3: Starting driver with initial channel: 2412 MHz
[ 2510.180621] ath: phy3: Attach a VIF of type: 2
[ 2510.180663] ath: phy3: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2510.180672] ath: phy3: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2510.180678] ath: phy3: Configure tx [queue/halq] [2/2], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2510.180685] ath: phy3: Configure tx [queue/halq] [3/3], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2510.180693] ath: phy3: Monitor mode is disabled
[ 2510.180696] ath: phy3: Set channel: 2412 MHz width: 0
[ 2510.180828] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 0
[ 2510.186699] ath: phy3: Set power: 16
[ 2510.186747] ath: phy3: Set HW RX filter: 0x207
[ 2510.186754] ath: phy3: Set HW RX filter: 0x207
[ 2510.187164] IPv6: ADDRCONF(NETDEV_UP): wlan11: link is not ready
[ 2510.187178] ath: phy3: Set HW RX filter: 0x207
[ 2510.204930] ath: phy3: Set HW RX filter: 0x17
[ 2510.205106] ath: phy3: Set channel: 2412 MHz width: 0
[ 2510.205245] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 0
[ 2510.268663] ath: phy3: Set channel: 2417 MHz width: 0
[ 2510.268819] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2510.269736] ath: phy3: Set power: 17
[ 2510.329709] ath: phy3: Set channel: 2422 MHz width: 0
[ 2510.329843] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2510.390717] ath: phy3: Set channel: 2427 MHz width: 0
[ 2510.390848] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2510.451723] ath: phy3: Set channel: 2432 MHz width: 0
[ 2510.451881] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2510.512792] ath: phy3: Set channel: 2437 MHz width: 0
[ 2510.512930] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2510.573809] ath: phy3: Set channel: 2442 MHz width: 0
[ 2510.573937] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2510.634850] ath: phy3: Set channel: 2447 MHz width: 0
[ 2510.634986] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2510.695864] ath: phy3: Set channel: 2452 MHz width: 0
[ 2510.696035] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2510.756906] ath: phy3: Set channel: 2457 MHz width: 0
[ 2510.757043] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2510.758024] ath: phy3: Set power: 16
[ 2510.817938] ath: phy3: Set channel: 2462 MHz width: 0
[ 2510.818075] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2510.819060] ath: phy3: Set power: 17
[ 2510.878987] ath: phy3: Set channel: 2467 MHz width: 0
[ 2510.879130] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2510.991013] ath: phy3: Set channel: 2472 MHz width: 0
[ 2510.991162] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2510.992126] ath: phy3: Set power: 16
[ 2511.103066] ath: phy3: Set channel: 5180 MHz width: 0
[ 2511.103191] ath: phy3: Reset to 5180 MHz, HT40: 0 fastcc: 1
[ 2511.108162] ath: phy3: Set power: 15
[ 2511.219123] ath: phy3: Set channel: 5200 MHz width: 0
[ 2511.219260] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2511.331179] ath: phy3: Set channel: 5220 MHz width: 0
[ 2511.331315] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2511.443222] ath: phy3: Set channel: 5240 MHz width: 0
[ 2511.443370] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2511.555273] ath: phy3: Set channel: 5260 MHz width: 0
[ 2511.555399] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2511.556327] ath: phy3: Set power: 17
[ 2511.667332] ath: phy3: Set channel: 5280 MHz width: 0
[ 2511.667482] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2511.668419] ath: phy3: Set power: 15
[ 2511.779362] ath: phy3: Set channel: 5300 MHz width: 0
[ 2511.779514] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2511.891446] ath: phy3: Set channel: 5320 MHz width: 0
[ 2511.891592] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2512.003483] ath: phy3: Set channel: 5500 MHz width: 0
[ 2512.003610] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2512.004534] ath: phy3: Set power: 16
[ 2512.115498] ath: phy3: Set channel: 5520 MHz width: 0
[ 2512.115659] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2512.116636] ath: phy3: Set power: 17
[ 2512.227558] ath: phy3: Set channel: 5540 MHz width: 0
[ 2512.227710] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2512.339637] ath: phy3: Set channel: 5560 MHz width: 0
[ 2512.339769] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2512.451690] ath: phy3: Set channel: 5580 MHz width: 0
[ 2512.451819] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2512.563740] ath: phy3: Set channel: 5600 MHz width: 0
[ 2512.563879] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2512.675791] ath: phy3: Set channel: 5620 MHz width: 0
[ 2512.675930] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2512.787793] ath: phy3: Set channel: 5640 MHz width: 0
[ 2512.787929] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2512.899909] ath: phy3: Set channel: 5660 MHz width: 0
[ 2512.900047] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2513.011950] ath: phy3: Set channel: 5680 MHz width: 0
[ 2513.012089] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2513.123963] ath: phy3: Set channel: 5700 MHz width: 0
[ 2513.124121] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2513.125039] ath: phy3: Set power: 16
[ 2513.236052] ath: phy3: Set channel: 5745 MHz width: 0
[ 2513.236187] ath: phy3: Reset to 5745 MHz, HT40: 0 fastcc: 1
[ 2513.237107] ath: phy3: Set power: 17
[ 2513.348104] ath: phy3: Set channel: 5765 MHz width: 0
[ 2513.348227] ath: phy3: Reset to 5765 MHz, HT40: 0 fastcc: 1
[ 2513.460146] ath: phy3: Set channel: 5785 MHz width: 0
[ 2513.460284] ath: phy3: Reset to 5785 MHz, HT40: 0 fastcc: 1
[ 2513.572199] ath: phy3: Set channel: 5805 MHz width: 0
[ 2513.572338] ath: phy3: Reset to 5805 MHz, HT40: 0 fastcc: 1
[ 2513.684257] ath: phy3: Set channel: 5825 MHz width: 0
[ 2513.684386] ath: phy3: Reset to 5825 MHz, HT40: 0 fastcc: 1
[ 2513.796312] ath: phy3: Set channel: 2412 MHz width: 0
[ 2513.796444] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 0
[ 2513.800534] ath: phy3: Set power: 16
[ 2513.800569] ath: phy3: Set HW RX filter: 0x207
[ 2513.856652] ath: phy3: Set HW RX filter: 0x17
[ 2513.856662] ath: phy3: Set channel: 2412 MHz width: 0
[ 2513.856789] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 0
[ 2513.920366] ath: phy3: Set channel: 2417 MHz width: 0
[ 2513.920489] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2513.921390] ath: phy3: Set power: 17
[ 2513.981399] ath: phy3: Set channel: 2422 MHz width: 0
[ 2513.981538] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2514.042406] ath: phy3: Set channel: 2427 MHz width: 0
[ 2514.042557] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2514.103452] ath: phy3: Set channel: 2432 MHz width: 0
[ 2514.103588] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2514.164480] ath: phy3: Set channel: 2437 MHz width: 0
[ 2514.164620] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2514.225510] ath: phy3: Set channel: 2442 MHz width: 0
[ 2514.225646] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2514.286525] ath: phy3: Set channel: 2447 MHz width: 0
[ 2514.286672] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2514.347537] ath: phy3: Set channel: 2452 MHz width: 0
[ 2514.347697] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2514.408540] ath: phy3: Set channel: 2457 MHz width: 0
[ 2514.408688] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2514.409667] ath: phy3: Set power: 16
[ 2514.469578] ath: phy3: Set channel: 2462 MHz width: 0
[ 2514.469715] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2514.470688] ath: phy3: Set power: 17
[ 2514.530606] ath: phy3: Set channel: 2467 MHz width: 0
[ 2514.530776] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2514.642705] ath: phy3: Set channel: 2472 MHz width: 0
[ 2514.642860] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2514.643822] ath: phy3: Set power: 16
[ 2514.754757] ath: phy3: Set channel: 5180 MHz width: 0
[ 2514.754883] ath: phy3: Reset to 5180 MHz, HT40: 0 fastcc: 1
[ 2514.759816] ath: phy3: Set power: 15
[ 2514.819799] ath: phy3: Set channel: 5200 MHz width: 0
[ 2514.819954] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2514.931776] ath: phy3: Set channel: 5220 MHz width: 0
[ 2514.931929] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2515.043840] ath: phy3: Set channel: 5240 MHz width: 0
[ 2515.044010] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2515.155942] ath: phy3: Set channel: 5260 MHz width: 0
[ 2515.156076] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2515.156986] ath: phy3: Set power: 17
[ 2515.267998] ath: phy3: Set channel: 5280 MHz width: 0
[ 2515.268128] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2515.269035] ath: phy3: Set power: 15
[ 2515.380022] ath: phy3: Set channel: 5300 MHz width: 0
[ 2515.380170] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2515.492092] ath: phy3: Set channel: 5320 MHz width: 0
[ 2515.492230] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2515.604144] ath: phy3: Set channel: 5500 MHz width: 0
[ 2515.604273] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2515.605193] ath: phy3: Set power: 16
[ 2515.716200] ath: phy3: Set channel: 5520 MHz width: 0
[ 2515.716328] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2515.717279] ath: phy3: Set power: 17
[ 2515.828257] ath: phy3: Set channel: 5540 MHz width: 0
[ 2515.828419] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2515.940245] ath: phy3: Set channel: 5560 MHz width: 0
[ 2515.940383] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2516.052352] ath: phy3: Set channel: 5580 MHz width: 0
[ 2516.052485] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2516.164412] ath: phy3: Set channel: 5600 MHz width: 0
[ 2516.164543] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2516.276455] ath: phy3: Set channel: 5620 MHz width: 0
[ 2516.276592] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2516.388507] ath: phy3: Set channel: 5640 MHz width: 0
[ 2516.388645] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2516.500556] ath: phy3: Set channel: 5660 MHz width: 0
[ 2516.500690] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2516.612608] ath: phy3: Set channel: 5680 MHz width: 0
[ 2516.612733] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2516.724662] ath: phy3: Set channel: 5700 MHz width: 0
[ 2516.724802] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2516.725720] ath: phy3: Set power: 16
[ 2516.836717] ath: phy3: Set channel: 5745 MHz width: 0
[ 2516.836856] ath: phy3: Reset to 5745 MHz, HT40: 0 fastcc: 1
[ 2516.837771] ath: phy3: Set power: 17
[ 2516.948723] ath: phy3: Set channel: 5765 MHz width: 0
[ 2516.948870] ath: phy3: Reset to 5765 MHz, HT40: 0 fastcc: 1
[ 2517.060762] ath: phy3: Set channel: 5785 MHz width: 0
[ 2517.060893] ath: phy3: Reset to 5785 MHz, HT40: 0 fastcc: 1
[ 2517.172853] ath: phy3: Set channel: 5805 MHz width: 0
[ 2517.173019] ath: phy3: Reset to 5805 MHz, HT40: 0 fastcc: 1
[ 2517.284920] ath: phy3: Set channel: 5825 MHz width: 0
[ 2517.285058] ath: phy3: Reset to 5825 MHz, HT40: 0 fastcc: 1
[ 2517.396981] ath: phy3: Set channel: 2412 MHz width: 0
[ 2517.397120] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 0
[ 2517.397493] wlan11: authenticate with 90:f6:52:ff:d3:85
[ 2517.401284] ath: phy3: Set power: 16
[ 2517.401319] ath: phy3: Set HW RX filter: 0x207
[ 2517.401353] ath: phy3: Set channel: 2437 MHz width: 2
[ 2517.401490] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2517.407648] ath: phy3: Set power: 17
[ 2517.407716] wlan11: send auth to 90:f6:52:ff:d3:85 (try 1/3)
[ 2517.410057] wlan11: authenticated
[ 2517.410954] wlan11: associate with 90:f6:52:ff:d3:85 (try 1/3)
[ 2517.414675] wlan11: RX AssocResp from 90:f6:52:ff:d3:85 (capab=0x431 status=0 aid=2)
[ 2517.414686] ath: phy3: Configure tx [queue/halq] [2/2], aifs: 3, cw_min: 15, cw_max: 1023, txop: 0
[ 2517.414690] ath: phy3: Configure tx [queue/halq] [3/3], aifs: 7, cw_min: 15, cw_max: 1023, txop: 0
[ 2517.414694] ath: phy3: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 7, cw_max: 15, txop: 94
[ 2517.414698] ath: phy3: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 3, cw_max: 7, txop: 47
[ 2517.414702] ath: phy3: BSSID 90:f6:52:ff:d3:85 Changed ASSOC 1
[ 2517.414705] ath: phy3: Primary Station interface: 68:94:23:16:16:75, BSSID: 90:f6:52:ff:d3:85
[ 2517.414725] wlan11: associated
[ 2517.414734] IPv6: ADDRCONF(NETDEV_CHANGE): wlan11: link becomes ready
[ 2517.415043] cfg80211: Calling CRDA for country: DE
[ 2517.415071] ath: phy3: Set HW RX filter: 0x607
[ 2517.417500] ath: EEPROM regdomain: 0x8114
[ 2517.417502] ath: EEPROM indicates we should expect a country code
[ 2517.417503] ath: doing EEPROM country->regdmn map search
[ 2517.417505] ath: country maps to regdmn code: 0x37
[ 2517.417506] ath: Country alpha2 being used: DE
[ 2517.417507] ath: Regpair used: 0x37
[ 2517.417508] ath: regdomain 0x8114 dynamically updated by country IE
[ 2517.417537] cfg80211: Regulatory domain changed to country: DE
[ 2517.417538] cfg80211:  DFS Master region: unset
[ 2517.417539] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2517.417541] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2517.417542] cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2517.417543] cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2517.417545] cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[ 2517.417546] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 2517.420943] ath: phy3: Set HW Key
[ 2517.421062] ath: phy3: Set HW Key
[ 2517.425901] ath: phy3: Set HW RX filter: 0x607
[ 2517.450020] ath: phy3: Set HW RX filter: 0x607
[ 2519.023942] ath: phy3: Set HW RX filter: 0x607
[ 2524.734736] ath: phy3: Set HW RX filter: 0x607
[ 2526.235659] ath: phy3: Set HW RX filter: 0x607
[ 2533.198074] ath: phy3: Set HW RX filter: 0x417
[ 2533.198089] ath: phy3: Set channel: 2412 MHz width: 0
[ 2533.198220] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2533.262294] ath: phy3: Set channel: 2417 MHz width: 0
[ 2533.262430] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2533.323303] ath: phy3: Set channel: 2437 MHz width: 2
[ 2533.323447] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2533.527684] ath: phy3: Set channel: 2422 MHz width: 0
[ 2533.527831] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2533.592474] ath: phy3: Set channel: 2427 MHz width: 0
[ 2533.592623] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2533.653469] ath: phy3: Set channel: 2437 MHz width: 2
[ 2533.653602] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2533.857854] ath: phy3: Set channel: 2432 MHz width: 0
[ 2533.858016] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2533.922609] ath: phy3: Set channel: 2437 MHz width: 2
[ 2533.922747] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2533.986611] ath: phy3: Set channel: 2437 MHz width: 2
[ 2533.986769] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2534.190965] ath: phy3: Set channel: 2442 MHz width: 0
[ 2534.191114] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2534.255739] ath: phy3: Set channel: 2447 MHz width: 0
[ 2534.255894] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2534.316762] ath: phy3: Set channel: 2437 MHz width: 2
[ 2534.316913] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2534.521141] ath: phy3: Set channel: 2452 MHz width: 0
[ 2534.521296] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2534.585914] ath: phy3: Set channel: 2457 MHz width: 0
[ 2534.586072] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2534.646929] ath: phy3: Set channel: 2437 MHz width: 2
[ 2534.647070] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2534.851327] ath: phy3: Set channel: 2462 MHz width: 0
[ 2534.851495] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2534.916083] ath: phy3: Set channel: 2437 MHz width: 2
[ 2534.916225] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2535.120415] ath: phy3: Set channel: 2467 MHz width: 0
[ 2535.120583] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2535.236186] ath: phy3: Set channel: 2437 MHz width: 2
[ 2535.236339] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2535.440568] ath: phy3: Set channel: 2472 MHz width: 0
[ 2535.440747] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2535.495284] ath: phy3: BB_WATCHDOG: Skipping interrupts
[ 2535.495452] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 0
[ 2535.556341] ath: phy3: Set channel: 2437 MHz width: 2
[ 2535.556494] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2535.760712] ath: phy3: Set channel: 5180 MHz width: 0
[ 2535.760848] ath: phy3: Reset to 5180 MHz, HT40: 0 fastcc: 1
[ 2535.876499] ath: phy3: Set channel: 2437 MHz width: 2
[ 2535.876636] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2536.081183] ath: phy3: Set channel: 5200 MHz width: 0
[ 2536.081317] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2536.196656] ath: phy3: Set channel: 2437 MHz width: 2
[ 2536.196816] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2536.401019] ath: phy3: Set channel: 5220 MHz width: 0
[ 2536.401168] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2536.516808] ath: phy3: Set channel: 2437 MHz width: 2
[ 2536.516969] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2536.721143] ath: phy3: Set channel: 5240 MHz width: 0
[ 2536.721287] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2536.836942] ath: phy3: Set channel: 2437 MHz width: 2
[ 2536.837096] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2537.041303] ath: phy3: Set channel: 5260 MHz width: 0
[ 2537.041438] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2537.157047] ath: phy3: Set channel: 2437 MHz width: 2
[ 2537.157199] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2537.361459] ath: phy3: Set channel: 5280 MHz width: 0
[ 2537.361606] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2537.477222] ath: phy3: Set channel: 2437 MHz width: 2
[ 2537.477375] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2537.681559] ath: phy3: Set channel: 5300 MHz width: 0
[ 2537.681693] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2537.797397] ath: phy3: Set channel: 2437 MHz width: 2
[ 2537.797550] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2538.001724] ath: phy3: Set channel: 5320 MHz width: 0
[ 2538.001863] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2538.117537] ath: phy3: Set channel: 2437 MHz width: 2
[ 2538.117689] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2538.321874] ath: phy3: Set channel: 5500 MHz width: 0
[ 2538.322042] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2538.437685] ath: phy3: Set channel: 2437 MHz width: 2
[ 2538.437836] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2538.642011] ath: phy3: Set channel: 5520 MHz width: 0
[ 2538.642136] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2538.757829] ath: phy3: Set channel: 2437 MHz width: 2
[ 2538.757963] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2538.962159] ath: phy3: Set channel: 5540 MHz width: 0
[ 2538.962324] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2539.077968] ath: phy3: Set channel: 2437 MHz width: 2
[ 2539.078124] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2539.282296] ath: phy3: Set channel: 5560 MHz width: 0
[ 2539.282432] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2539.398124] ath: phy3: Set channel: 2437 MHz width: 2
[ 2539.398261] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2539.602460] ath: phy3: Set channel: 5580 MHz width: 0
[ 2539.602601] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2539.718275] ath: phy3: Set channel: 2437 MHz width: 2
[ 2539.718411] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2539.922618] ath: phy3: Set channel: 5600 MHz width: 0
[ 2539.922762] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2540.038422] ath: phy3: Set channel: 2437 MHz width: 2
[ 2540.038571] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2540.242743] ath: phy3: Set channel: 5620 MHz width: 0
[ 2540.242875] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2540.358550] ath: phy3: Set channel: 2437 MHz width: 2
[ 2540.358703] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2540.562910] ath: phy3: Set channel: 5640 MHz width: 0
[ 2540.563032] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2540.678665] ath: phy3: Set channel: 2437 MHz width: 2
[ 2540.678807] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2540.883033] ath: phy3: Set channel: 5660 MHz width: 0
[ 2540.883176] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2540.998865] ath: phy3: Set channel: 2437 MHz width: 2
[ 2540.999004] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2541.203198] ath: phy3: Set channel: 5680 MHz width: 0
[ 2541.203328] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2541.319000] ath: phy3: Set channel: 2437 MHz width: 2
[ 2541.319148] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2541.523366] ath: phy3: Set channel: 5700 MHz width: 0
[ 2541.523506] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2541.639157] ath: phy3: Set channel: 2437 MHz width: 2
[ 2541.639296] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2541.643799] ath: phy3: Set HW RX filter: 0x607
[ 2576.219557] ath: phy3: Set HW RX filter: 0x417
[ 2576.219586] ath: phy3: Set channel: 2412 MHz width: 0
[ 2576.219722] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2576.284133] ath: phy3: Set channel: 2417 MHz width: 0
[ 2576.284275] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2576.345171] ath: phy3: Set channel: 2437 MHz width: 2
[ 2576.345318] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2576.549482] ath: phy3: Set channel: 2422 MHz width: 0
[ 2576.549616] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2576.614304] ath: phy3: Set channel: 2427 MHz width: 0
[ 2576.614443] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2576.675308] ath: phy3: Set channel: 2437 MHz width: 2
[ 2576.675453] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2576.879713] ath: phy3: Set channel: 2432 MHz width: 0
[ 2576.879868] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2576.944466] ath: phy3: Set channel: 2437 MHz width: 2
[ 2576.944611] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2577.008483] ath: phy3: Set channel: 2437 MHz width: 2
[ 2577.008611] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2577.213369] ath: phy3: Set channel: 2442 MHz width: 0
[ 2577.213501] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2577.277603] ath: phy3: Set channel: 2447 MHz width: 0
[ 2577.277757] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2577.338634] ath: phy3: Set channel: 2437 MHz width: 2
[ 2577.338792] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2577.542998] ath: phy3: Set channel: 2452 MHz width: 0
[ 2577.543143] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2577.607771] ath: phy3: Set channel: 2457 MHz width: 0
[ 2577.607906] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2577.668786] ath: phy3: Set channel: 2437 MHz width: 2
[ 2577.668923] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2577.873133] ath: phy3: Set channel: 2462 MHz width: 0
[ 2577.873269] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2577.937877] ath: phy3: Set channel: 2437 MHz width: 2
[ 2577.938028] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2578.142256] ath: phy3: Set channel: 2467 MHz width: 0
[ 2578.142396] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2578.258039] ath: phy3: Set channel: 2437 MHz width: 2
[ 2578.258194] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2578.462413] ath: phy3: Set channel: 2472 MHz width: 0
[ 2578.462554] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2578.578208] ath: phy3: Set channel: 2437 MHz width: 2
[ 2578.578356] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2578.782552] ath: phy3: Set channel: 5180 MHz width: 0
[ 2578.782686] ath: phy3: Reset to 5180 MHz, HT40: 0 fastcc: 1
[ 2578.898343] ath: phy3: Set channel: 2437 MHz width: 2
[ 2578.898499] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2579.102696] ath: phy3: Set channel: 5200 MHz width: 0
[ 2579.102844] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2579.218512] ath: phy3: Set channel: 2437 MHz width: 2
[ 2579.218672] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2579.422846] ath: phy3: Set channel: 5220 MHz width: 0
[ 2579.422983] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2579.538590] ath: phy3: Set channel: 2437 MHz width: 2
[ 2579.538762] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2579.742990] ath: phy3: Set channel: 5240 MHz width: 0
[ 2579.743121] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2579.858782] ath: phy3: Set channel: 2437 MHz width: 2
[ 2579.858927] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2580.063126] ath: phy3: Set channel: 5260 MHz width: 0
[ 2580.063266] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2580.178946] ath: phy3: Set channel: 2437 MHz width: 2
[ 2580.179084] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2580.383303] ath: phy3: Set channel: 5280 MHz width: 0
[ 2580.383446] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2580.499086] ath: phy3: Set channel: 2437 MHz width: 2
[ 2580.499244] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2580.703434] ath: phy3: Set channel: 5300 MHz width: 0
[ 2580.703572] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2580.819231] ath: phy3: Set channel: 2437 MHz width: 2
[ 2580.819388] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2581.023594] ath: phy3: Set channel: 5320 MHz width: 0
[ 2581.023735] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2581.139392] ath: phy3: Set channel: 2437 MHz width: 2
[ 2581.139548] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2581.343756] ath: phy3: Set channel: 5500 MHz width: 0
[ 2581.343896] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2581.459519] ath: phy3: Set channel: 2437 MHz width: 2
[ 2581.459672] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2581.663851] ath: phy3: Set channel: 5520 MHz width: 0
[ 2581.663986] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2581.779673] ath: phy3: Set channel: 2437 MHz width: 2
[ 2581.779827] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2581.984057] ath: phy3: Set channel: 5540 MHz width: 0
[ 2581.984199] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2582.099831] ath: phy3: Set channel: 2437 MHz width: 2
[ 2582.099968] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2582.304159] ath: phy3: Set channel: 5560 MHz width: 0
[ 2582.304294] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2582.419982] ath: phy3: Set channel: 2437 MHz width: 2
[ 2582.420119] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2582.624316] ath: phy3: Set channel: 5580 MHz width: 0
[ 2582.624453] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2582.740120] ath: phy3: Set channel: 2437 MHz width: 2
[ 2582.740280] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2582.944379] ath: phy3: Set channel: 5600 MHz width: 0
[ 2582.944509] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2583.060260] ath: phy3: Set channel: 2437 MHz width: 2
[ 2583.060408] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2583.264496] ath: phy3: Set channel: 5620 MHz width: 0
[ 2583.264638] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2583.380406] ath: phy3: Set channel: 2437 MHz width: 2
[ 2583.380557] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2583.584759] ath: phy3: Set channel: 5640 MHz width: 0
[ 2583.584895] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2583.700553] ath: phy3: Set channel: 2437 MHz width: 2
[ 2583.700704] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2583.904911] ath: phy3: Set channel: 5660 MHz width: 0
[ 2583.905049] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2584.020700] ath: phy3: Set channel: 2437 MHz width: 2
[ 2584.020848] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2584.225036] ath: phy3: Set channel: 5680 MHz width: 0
[ 2584.225174] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2584.340863] ath: phy3: Set channel: 2437 MHz width: 2
[ 2584.341012] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2584.545209] ath: phy3: Set channel: 5700 MHz width: 0
[ 2584.545344] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2584.661014] ath: phy3: Set channel: 2437 MHz width: 2
[ 2584.661176] ath: phy3: Reset to 2437 MHz, HT40: 1 fastcc: 0
[ 2584.665753] ath: phy3: Set HW RX filter: 0x607
[ 2602.000429] wlan11: deauthenticating from 90:f6:52:ff:d3:85 by local choice (reason=3)
[ 2602.001369] ath: phy3: Set HW Key
[ 2602.001443] ath: phy3: BSSID 00:00:00:00:00:00 Changed ASSOC 0
[ 2602.001462] ath: phy3: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2602.001467] ath: phy3: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2602.001471] ath: phy3: Configure tx [queue/halq] [2/2], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2602.001474] ath: phy3: Configure tx [queue/halq] [3/3], aifs: 2, cw_min: 15, cw_max: 1023, txop: 0
[ 2602.001480] ath: phy3: Set channel: 2437 MHz width: 0
[ 2602.001609] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 0
[ 2602.007520] ath: phy3: Set power: 20
[ 2602.007576] ath: phy3: Set HW Key
[ 2602.007638] cfg80211: Calling CRDA to update world regulatory domain
[ 2602.008284] ath: phy3: Set HW RX filter: 0x207
[ 2602.009476] ath: phy3: Set HW RX filter: 0x207
[ 2602.009940] ath: phy3: Set HW RX filter: 0x207
[ 2602.011412] cfg80211: World regulatory domain updated:
[ 2602.011416] cfg80211:  DFS Master region: unset
[ 2602.011417] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2602.011419] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2602.011421] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2602.011422] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 2602.011424] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2602.011425] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2602.060918] ath: phy3: Set power: 17
[ 2602.060938] ath: phy3: Set HW RX filter: 0x17
[ 2602.062545] ath: phy3: Set channel: 2412 MHz width: 0
[ 2602.062689] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2602.063613] ath: phy3: Set power: 16
[ 2602.123022] ath: phy3: Set channel: 2417 MHz width: 0
[ 2602.123204] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2602.124127] ath: phy3: Set power: 17
[ 2602.184114] ath: phy3: Set channel: 2422 MHz width: 0
[ 2602.184256] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2602.245144] ath: phy3: Set channel: 2427 MHz width: 0
[ 2602.245291] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2602.306108] ath: phy3: Set channel: 2432 MHz width: 0
[ 2602.306252] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2602.367170] ath: phy3: Set channel: 2437 MHz width: 0
[ 2602.367351] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 0
[ 2602.431214] ath: phy3: Set channel: 2442 MHz width: 0
[ 2602.431353] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2602.492232] ath: phy3: Set channel: 2447 MHz width: 0
[ 2602.492365] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2602.553276] ath: phy3: Set channel: 2452 MHz width: 0
[ 2602.553405] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2602.614304] ath: phy3: Set channel: 2457 MHz width: 0
[ 2602.614441] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2602.615405] ath: phy3: Set power: 16
[ 2602.675324] ath: phy3: Set channel: 2462 MHz width: 0
[ 2602.675458] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2602.676454] ath: phy3: Set power: 17
[ 2602.736356] ath: phy3: Set channel: 2467 MHz width: 0
[ 2602.736490] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2602.848394] ath: phy3: Set channel: 2472 MHz width: 0
[ 2602.848560] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2602.849595] ath: phy3: Set power: 16
[ 2602.960458] ath: phy3: Set channel: 5180 MHz width: 0
[ 2602.960599] ath: phy3: Reset to 5180 MHz, HT40: 0 fastcc: 1
[ 2602.965592] ath: phy3: Set power: 15
[ 2603.076463] ath: phy3: Set channel: 5200 MHz width: 0
[ 2603.076602] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2603.188567] ath: phy3: Set channel: 5220 MHz width: 0
[ 2603.188701] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2603.300639] ath: phy3: Set channel: 5240 MHz width: 0
[ 2603.300778] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2603.412669] ath: phy3: Set channel: 5260 MHz width: 0
[ 2603.412808] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2603.413727] ath: phy3: Set power: 17
[ 2603.524739] ath: phy3: Set channel: 5280 MHz width: 0
[ 2603.524895] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2603.525834] ath: phy3: Set power: 15
[ 2603.636767] ath: phy3: Set channel: 5300 MHz width: 0
[ 2603.636902] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2603.748827] ath: phy3: Set channel: 5320 MHz width: 0
[ 2603.748977] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2603.860822] ath: phy3: Set channel: 5500 MHz width: 0
[ 2603.860960] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2603.861884] ath: phy3: Set power: 16
[ 2603.972929] ath: phy3: Set channel: 5520 MHz width: 0
[ 2603.973068] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2603.974037] ath: phy3: Set power: 17
[ 2604.084931] ath: phy3: Set channel: 5540 MHz width: 0
[ 2604.085074] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2604.197038] ath: phy3: Set channel: 5560 MHz width: 0
[ 2604.197174] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2604.309029] ath: phy3: Set channel: 5580 MHz width: 0
[ 2604.309167] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2604.421151] ath: phy3: Set channel: 5600 MHz width: 0
[ 2604.421299] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2604.533127] ath: phy3: Set channel: 5620 MHz width: 0
[ 2604.533265] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2604.645238] ath: phy3: Set channel: 5640 MHz width: 0
[ 2604.645374] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2604.757295] ath: phy3: Set channel: 5660 MHz width: 0
[ 2604.757440] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2604.869342] ath: phy3: Set channel: 5680 MHz width: 0
[ 2604.869495] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2604.981394] ath: phy3: Set channel: 5700 MHz width: 0
[ 2604.981526] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2604.982445] ath: phy3: Set power: 16
[ 2605.093442] ath: phy3: Set channel: 5745 MHz width: 0
[ 2605.093583] ath: phy3: Reset to 5745 MHz, HT40: 0 fastcc: 1
[ 2605.094499] ath: phy3: Set power: 17
[ 2605.205496] ath: phy3: Set channel: 5765 MHz width: 0
[ 2605.205635] ath: phy3: Reset to 5765 MHz, HT40: 0 fastcc: 1
[ 2605.317517] ath: phy3: Set channel: 5785 MHz width: 0
[ 2605.317658] ath: phy3: Reset to 5785 MHz, HT40: 0 fastcc: 1
[ 2605.429604] ath: phy3: Set channel: 5805 MHz width: 0
[ 2605.429741] ath: phy3: Reset to 5805 MHz, HT40: 0 fastcc: 1
[ 2605.541657] ath: phy3: Set channel: 5825 MHz width: 0
[ 2605.541798] ath: phy3: Reset to 5825 MHz, HT40: 0 fastcc: 1
[ 2605.653706] ath: phy3: Set channel: 2437 MHz width: 0
[ 2605.653854] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 0
[ 2605.654146] wlan11: authenticate with 90:f6:52:ff:d3:86
[ 2605.658025] ath: phy3: Set HW RX filter: 0x207
[ 2605.658059] ath: phy3: Set channel: 5180 MHz width: 2
[ 2605.658191] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2605.664412] ath: phy3: Set power: 15
[ 2605.664490] wlan11: direct probe to 90:f6:52:ff:d3:86 (try 1/3)
[ 2605.864798] wlan11: send auth to 90:f6:52:ff:d3:86 (try 2/3)
[ 2605.866348] wlan11: authenticated
[ 2605.866764] wlan11: associate with 90:f6:52:ff:d3:86 (try 1/3)
[ 2605.869212] wlan11: RX AssocResp from 90:f6:52:ff:d3:86 (capab=0x11 status=0 aid=1)
[ 2605.869226] ath: phy3: Configure tx [queue/halq] [2/2], aifs: 3, cw_min: 15, cw_max: 1023, txop: 0
[ 2605.869231] ath: phy3: Configure tx [queue/halq] [3/3], aifs: 7, cw_min: 15, cw_max: 1023, txop: 0
[ 2605.869236] ath: phy3: Configure tx [queue/halq] [1/1], aifs: 2, cw_min: 7, cw_max: 15, txop: 94
[ 2605.869240] ath: phy3: Configure tx [queue/halq] [0/0], aifs: 2, cw_min: 3, cw_max: 7, txop: 47
[ 2605.869245] ath: phy3: BSSID 90:f6:52:ff:d3:86 Changed ASSOC 1
[ 2605.869247] ath: phy3: Primary Station interface: 68:94:23:16:16:75, BSSID: 90:f6:52:ff:d3:86
[ 2605.869270] wlan11: associated
[ 2605.869381] cfg80211: Calling CRDA for country: DE
[ 2605.871812] ath: EEPROM regdomain: 0x8114
[ 2605.871815] ath: EEPROM indicates we should expect a country code
[ 2605.871816] ath: doing EEPROM country->regdmn map search
[ 2605.871817] ath: country maps to regdmn code: 0x37
[ 2605.871819] ath: Country alpha2 being used: DE
[ 2605.871820] ath: Regpair used: 0x37
[ 2605.871821] ath: regdomain 0x8114 dynamically updated by country IE
[ 2605.871850] cfg80211: Regulatory domain changed to country: DE
[ 2605.871851] cfg80211:  DFS Master region: unset
[ 2605.871853] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2605.871854] cfg80211:   (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2605.871856] cfg80211:   (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2605.871857] cfg80211:   (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2605.871859] cfg80211:   (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[ 2605.871860] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 2605.875213] ath: phy3: Set HW Key
[ 2605.875331] ath: phy3: Set HW Key
[ 2605.880303] ath: phy3: Set HW RX filter: 0x607
[ 2605.882549] ath: phy3: Set HW RX filter: 0x607
[ 2605.906969] ath: phy3: Set HW RX filter: 0x607
[ 2607.760940] ath: phy3: Set HW RX filter: 0x607
[ 2612.319448] ath: phy3: Set HW RX filter: 0x607
[ 2613.403771] ath: phy3: Set HW RX filter: 0x607
[ 2628.241718] ath: phy3: Set HW RX filter: 0x417
[ 2628.241731] ath: phy3: Set channel: 2412 MHz width: 0
[ 2628.241878] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2628.306137] ath: phy3: Set channel: 2417 MHz width: 0
[ 2628.306279] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2628.367184] ath: phy3: Set channel: 5180 MHz width: 2
[ 2628.367319] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2628.571538] ath: phy3: Set channel: 2422 MHz width: 0
[ 2628.571683] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2628.636309] ath: phy3: Set channel: 5180 MHz width: 2
[ 2628.636448] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2628.840671] ath: phy3: Set channel: 2427 MHz width: 0
[ 2628.840818] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2628.905417] ath: phy3: Set channel: 2432 MHz width: 0
[ 2628.905564] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2628.966476] ath: phy3: Set channel: 5180 MHz width: 2
[ 2628.966625] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2629.170812] ath: phy3: Set channel: 2437 MHz width: 0
[ 2629.170949] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2629.235581] ath: phy3: Set channel: 2442 MHz width: 0
[ 2629.235713] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2629.296595] ath: phy3: Set channel: 5180 MHz width: 2
[ 2629.296745] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2629.500976] ath: phy3: Set channel: 2447 MHz width: 0
[ 2629.501121] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2629.565742] ath: phy3: Set channel: 2452 MHz width: 0
[ 2629.565877] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2629.626763] ath: phy3: Set channel: 5180 MHz width: 2
[ 2629.626890] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2629.831045] ath: phy3: Set channel: 2457 MHz width: 0
[ 2629.831166] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2629.895888] ath: phy3: Set channel: 2462 MHz width: 0
[ 2629.896013] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2629.956933] ath: phy3: Set channel: 5180 MHz width: 2
[ 2629.957075] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2630.161243] ath: phy3: Set channel: 2467 MHz width: 0
[ 2630.161387] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2630.277048] ath: phy3: Set channel: 5180 MHz width: 2
[ 2630.277198] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2630.481414] ath: phy3: Set channel: 2472 MHz width: 0
[ 2630.481553] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2630.536172] ath: phy3: BB_WATCHDOG: Skipping interrupts
[ 2630.536317] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 0
[ 2630.597199] ath: phy3: Set channel: 5180 MHz width: 2
[ 2630.597353] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2630.801579] ath: phy3: Set channel: 5180 MHz width: 2
[ 2630.801727] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2630.916377] ath: phy3: Set channel: 5180 MHz width: 2
[ 2630.916516] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2631.120724] ath: phy3: Set channel: 5200 MHz width: 0
[ 2631.120882] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2631.236507] ath: phy3: Set channel: 5180 MHz width: 2
[ 2631.236656] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2631.440868] ath: phy3: Set channel: 5220 MHz width: 0
[ 2631.441022] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2631.556659] ath: phy3: Set channel: 5180 MHz width: 2
[ 2631.556799] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2631.760989] ath: phy3: Set channel: 5240 MHz width: 0
[ 2631.761138] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2631.876806] ath: phy3: Set channel: 5180 MHz width: 2
[ 2631.876938] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2632.081158] ath: phy3: Set channel: 5260 MHz width: 0
[ 2632.081306] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2632.196954] ath: phy3: Set channel: 5180 MHz width: 2
[ 2632.197089] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2632.401308] ath: phy3: Set channel: 5280 MHz width: 0
[ 2632.401455] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2632.517097] ath: phy3: Set channel: 5180 MHz width: 2
[ 2632.517230] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2632.721453] ath: phy3: Set channel: 5300 MHz width: 0
[ 2632.721596] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2632.837243] ath: phy3: Set channel: 5180 MHz width: 2
[ 2632.837379] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2633.041616] ath: phy3: Set channel: 5320 MHz width: 0
[ 2633.041767] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2633.157409] ath: phy3: Set channel: 5180 MHz width: 2
[ 2633.157555] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2633.361736] ath: phy3: Set channel: 5500 MHz width: 0
[ 2633.361879] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2633.477543] ath: phy3: Set channel: 5180 MHz width: 2
[ 2633.477676] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2633.681897] ath: phy3: Set channel: 5520 MHz width: 0
[ 2633.682043] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2633.797689] ath: phy3: Set channel: 5180 MHz width: 2
[ 2633.797824] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2634.002045] ath: phy3: Set channel: 5540 MHz width: 0
[ 2634.002191] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2634.117840] ath: phy3: Set channel: 5180 MHz width: 2
[ 2634.117977] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2634.322190] ath: phy3: Set channel: 5560 MHz width: 0
[ 2634.322334] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2634.437982] ath: phy3: Set channel: 5180 MHz width: 2
[ 2634.438116] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2634.642342] ath: phy3: Set channel: 5580 MHz width: 0
[ 2634.642489] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2634.758133] ath: phy3: Set channel: 5180 MHz width: 2
[ 2634.758263] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2634.962362] ath: phy3: Set channel: 5600 MHz width: 0
[ 2634.962497] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2635.078265] ath: phy3: Set channel: 5180 MHz width: 2
[ 2635.078415] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2635.282631] ath: phy3: Set channel: 5620 MHz width: 0
[ 2635.282776] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2635.398415] ath: phy3: Set channel: 5180 MHz width: 2
[ 2635.398575] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2635.602762] ath: phy3: Set channel: 5640 MHz width: 0
[ 2635.602892] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2635.718579] ath: phy3: Set channel: 5180 MHz width: 2
[ 2635.718713] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2635.922932] ath: phy3: Set channel: 5660 MHz width: 0
[ 2635.923077] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2636.038728] ath: phy3: Set channel: 5180 MHz width: 2
[ 2636.038870] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2636.243090] ath: phy3: Set channel: 5680 MHz width: 0
[ 2636.243250] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2636.358875] ath: phy3: Set channel: 5180 MHz width: 2
[ 2636.359024] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2636.563226] ath: phy3: Set channel: 5700 MHz width: 0
[ 2636.563381] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2636.679028] ath: phy3: Set channel: 5180 MHz width: 2
[ 2636.679172] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2636.683640] ath: phy3: Set HW RX filter: 0x607
[ 2671.262584] ath: phy3: Set HW RX filter: 0x417
[ 2671.262610] ath: phy3: Set channel: 2412 MHz width: 0
[ 2671.262749] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2671.327010] ath: phy3: Set channel: 2417 MHz width: 0
[ 2671.327171] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2671.388031] ath: phy3: Set channel: 5180 MHz width: 2
[ 2671.388179] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2671.592398] ath: phy3: Set channel: 2422 MHz width: 0
[ 2671.592565] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2671.657137] ath: phy3: Set channel: 2427 MHz width: 0
[ 2671.657310] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2671.718182] ath: phy3: Set channel: 5180 MHz width: 2
[ 2671.718348] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2671.813207] rts51x: Command (unknown command) (16 bytes)
[ 2671.813216] rts51x: 
[ 2671.813221]  85 08
[ 2671.813229]  0e 00
[ 2671.813235]  00 00
[ 2671.813240]  01 00
[ 2671.813245]  00 00
[ 2671.813250]  00 00
[ 2671.813256]  00 40
[ 2671.813261]  ec 00
[ 2671.813267] 
[ 2671.922677] ath: phy3: Set channel: 2432 MHz width: 0
[ 2671.922848] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2671.987303] ath: phy3: Set channel: 2437 MHz width: 0
[ 2671.987487] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2672.048331] ath: phy3: Set channel: 5180 MHz width: 2
[ 2672.048500] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2672.252699] ath: phy3: Set channel: 2442 MHz width: 0
[ 2672.252862] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2672.317467] ath: phy3: Set channel: 2447 MHz width: 0
[ 2672.317645] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2672.378476] ath: phy3: Set channel: 5180 MHz width: 2
[ 2672.378625] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2672.582875] ath: phy3: Set channel: 2452 MHz width: 0
[ 2672.583026] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2672.647636] ath: phy3: Set channel: 2457 MHz width: 0
[ 2672.647795] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2672.708633] ath: phy3: Set channel: 5180 MHz width: 2
[ 2672.708782] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2672.912959] ath: phy3: Set channel: 2462 MHz width: 0
[ 2672.913130] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2672.977769] ath: phy3: Set channel: 5180 MHz width: 2
[ 2672.977938] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2673.182193] ath: phy3: Set channel: 2467 MHz width: 0
[ 2673.182360] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2673.297913] ath: phy3: Set channel: 5180 MHz width: 2
[ 2673.298082] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2673.502311] ath: phy3: Set channel: 2472 MHz width: 0
[ 2673.502479] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2673.618066] ath: phy3: Set channel: 5180 MHz width: 2
[ 2673.618237] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2673.822434] ath: phy3: Set channel: 5180 MHz width: 2
[ 2673.822613] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2673.938210] ath: phy3: Set channel: 5180 MHz width: 2
[ 2673.938376] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2674.142570] ath: phy3: Set channel: 5200 MHz width: 0
[ 2674.142734] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2674.258351] ath: phy3: Set channel: 5180 MHz width: 2
[ 2674.258516] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2674.462777] ath: phy3: Set channel: 5220 MHz width: 0
[ 2674.462941] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2674.578503] ath: phy3: Set channel: 5180 MHz width: 2
[ 2674.578669] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2674.782867] ath: phy3: Set channel: 5240 MHz width: 0
[ 2674.783035] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2674.898652] ath: phy3: Set channel: 5180 MHz width: 2
[ 2674.898817] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2675.103013] ath: phy3: Set channel: 5260 MHz width: 0
[ 2675.103182] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2675.218792] ath: phy3: Set channel: 5180 MHz width: 2
[ 2675.218956] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2675.423156] ath: phy3: Set channel: 5280 MHz width: 0
[ 2675.423322] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2675.538955] ath: phy3: Set channel: 5180 MHz width: 2
[ 2675.539121] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2675.743355] ath: phy3: Set channel: 5300 MHz width: 0
[ 2675.743523] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2675.859126] ath: phy3: Set channel: 5180 MHz width: 2
[ 2675.859293] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2676.063440] ath: phy3: Set channel: 5320 MHz width: 0
[ 2676.063604] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2676.179238] ath: phy3: Set channel: 5180 MHz width: 2
[ 2676.179405] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2676.383657] ath: phy3: Set channel: 5500 MHz width: 0
[ 2676.383805] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2676.499389] ath: phy3: Set channel: 5180 MHz width: 2
[ 2676.499534] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2676.703746] ath: phy3: Set channel: 5520 MHz width: 0
[ 2676.703887] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2676.819543] ath: phy3: Set channel: 5180 MHz width: 2
[ 2676.819676] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2677.023908] ath: phy3: Set channel: 5540 MHz width: 0
[ 2677.024065] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2677.139655] ath: phy3: Set channel: 5180 MHz width: 2
[ 2677.139830] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2677.344056] ath: phy3: Set channel: 5560 MHz width: 0
[ 2677.344203] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2677.459844] ath: phy3: Set channel: 5180 MHz width: 2
[ 2677.459980] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2677.664199] ath: phy3: Set channel: 5580 MHz width: 0
[ 2677.664345] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2677.779976] ath: phy3: Set channel: 5180 MHz width: 2
[ 2677.780138] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2677.984335] ath: phy3: Set channel: 5600 MHz width: 0
[ 2677.984483] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2678.100134] ath: phy3: Set channel: 5180 MHz width: 2
[ 2678.100282] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2678.304456] ath: phy3: Set channel: 5620 MHz width: 0
[ 2678.304589] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2678.420281] ath: phy3: Set channel: 5180 MHz width: 2
[ 2678.420413] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2678.624644] ath: phy3: Set channel: 5640 MHz width: 0
[ 2678.624788] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2678.740433] ath: phy3: Set channel: 5180 MHz width: 2
[ 2678.740569] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2678.944757] ath: phy3: Set channel: 5660 MHz width: 0
[ 2678.944889] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2679.060579] ath: phy3: Set channel: 5180 MHz width: 2
[ 2679.060713] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2679.264948] ath: phy3: Set channel: 5680 MHz width: 0
[ 2679.265095] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2679.380727] ath: phy3: Set channel: 5180 MHz width: 2
[ 2679.380859] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2679.585137] ath: phy3: Set channel: 5700 MHz width: 0
[ 2679.585298] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2679.700876] ath: phy3: Set channel: 5180 MHz width: 2
[ 2679.701030] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2679.705506] ath: phy3: Set HW RX filter: 0x607
[ 2734.288401] ath: phy3: Set HW RX filter: 0x417
[ 2734.288425] ath: phy3: Set channel: 2412 MHz width: 0
[ 2734.288561] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2734.353097] ath: phy3: Set channel: 2417 MHz width: 0
[ 2734.353236] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2734.414124] ath: phy3: Set channel: 5180 MHz width: 2
[ 2734.414255] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2734.618326] ath: phy3: Set channel: 2422 MHz width: 0
[ 2734.618471] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2734.683249] ath: phy3: Set channel: 2427 MHz width: 0
[ 2734.683385] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2734.744243] ath: phy3: Set channel: 5180 MHz width: 2
[ 2734.744394] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2734.948420] ath: phy3: Set channel: 2432 MHz width: 0
[ 2734.948558] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2735.013399] ath: phy3: Set channel: 2437 MHz width: 0
[ 2735.013530] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2735.074419] ath: phy3: Set channel: 5180 MHz width: 2
[ 2735.074566] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2735.278621] ath: phy3: Set channel: 2442 MHz width: 0
[ 2735.278756] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2735.343550] ath: phy3: Set channel: 2447 MHz width: 0
[ 2735.343687] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2735.404585] ath: phy3: Set channel: 5180 MHz width: 2
[ 2735.404740] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2735.608771] ath: phy3: Set channel: 2452 MHz width: 0
[ 2735.608910] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2735.673652] ath: phy3: Set channel: 2457 MHz width: 0
[ 2735.673788] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2735.734717] ath: phy3: Set channel: 5180 MHz width: 2
[ 2735.734867] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2735.938870] ath: phy3: Set channel: 2462 MHz width: 0
[ 2735.939004] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2736.003850] ath: phy3: Set channel: 5180 MHz width: 2
[ 2736.003990] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2736.208020] ath: phy3: Set channel: 2467 MHz width: 0
[ 2736.208157] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2736.323980] ath: phy3: Set channel: 5180 MHz width: 2
[ 2736.324137] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2736.528189] ath: phy3: Set channel: 2472 MHz width: 0
[ 2736.528325] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2736.644151] ath: phy3: Set channel: 5180 MHz width: 2
[ 2736.644288] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2736.848290] ath: phy3: Set channel: 5180 MHz width: 2
[ 2736.848425] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2736.963250] ath: phy3: Set channel: 5180 MHz width: 2
[ 2736.963390] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2737.167487] ath: phy3: Set channel: 5200 MHz width: 0
[ 2737.167635] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2737.283427] ath: phy3: Set channel: 5180 MHz width: 2
[ 2737.283585] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2737.487649] ath: phy3: Set channel: 5220 MHz width: 0
[ 2737.487791] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2737.603588] ath: phy3: Set channel: 5180 MHz width: 2
[ 2737.603733] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2737.807788] ath: phy3: Set channel: 5240 MHz width: 0
[ 2737.807934] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2737.923744] ath: phy3: Set channel: 5180 MHz width: 2
[ 2737.923882] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2738.127940] ath: phy3: Set channel: 5260 MHz width: 0
[ 2738.128083] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2738.243895] ath: phy3: Set channel: 5180 MHz width: 2
[ 2738.244032] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2738.448073] ath: phy3: Set channel: 5280 MHz width: 0
[ 2738.448215] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2738.564039] ath: phy3: Set channel: 5180 MHz width: 2
[ 2738.564192] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2738.768235] ath: phy3: Set channel: 5300 MHz width: 0
[ 2738.768381] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2738.884190] ath: phy3: Set channel: 5180 MHz width: 2
[ 2738.884334] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2739.088369] ath: phy3: Set channel: 5320 MHz width: 0
[ 2739.088502] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2739.204336] ath: phy3: Set channel: 5180 MHz width: 2
[ 2739.204475] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2739.408541] ath: phy3: Set channel: 5500 MHz width: 0
[ 2739.408689] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2739.524485] ath: phy3: Set channel: 5180 MHz width: 2
[ 2739.524622] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2739.728683] ath: phy3: Set channel: 5520 MHz width: 0
[ 2739.728826] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2739.844632] ath: phy3: Set channel: 5180 MHz width: 2
[ 2739.844783] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2740.048782] ath: phy3: Set channel: 5540 MHz width: 0
[ 2740.048932] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2740.164778] ath: phy3: Set channel: 5180 MHz width: 2
[ 2740.164913] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2740.368979] ath: phy3: Set channel: 5560 MHz width: 0
[ 2740.369124] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2740.484923] ath: phy3: Set channel: 5180 MHz width: 2
[ 2740.485058] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2740.689118] ath: phy3: Set channel: 5580 MHz width: 0
[ 2740.689263] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2740.805074] ath: phy3: Set channel: 5180 MHz width: 2
[ 2740.805212] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2741.009247] ath: phy3: Set channel: 5600 MHz width: 0
[ 2741.009388] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2741.125223] ath: phy3: Set channel: 5180 MHz width: 2
[ 2741.125360] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2741.329420] ath: phy3: Set channel: 5620 MHz width: 0
[ 2741.329566] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2741.445331] ath: phy3: Set channel: 5180 MHz width: 2
[ 2741.445484] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2741.649575] ath: phy3: Set channel: 5640 MHz width: 0
[ 2741.649722] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2741.765512] ath: phy3: Set channel: 5180 MHz width: 2
[ 2741.765648] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2741.969710] ath: phy3: Set channel: 5660 MHz width: 0
[ 2741.969852] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2742.085664] ath: phy3: Set channel: 5180 MHz width: 2
[ 2742.085802] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2742.289841] ath: phy3: Set channel: 5680 MHz width: 0
[ 2742.289979] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2742.405762] ath: phy3: Set channel: 5180 MHz width: 2
[ 2742.405915] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2742.610007] ath: phy3: Set channel: 5700 MHz width: 0
[ 2742.610149] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2742.725960] ath: phy3: Set channel: 5180 MHz width: 2
[ 2742.726103] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2742.730621] ath: phy3: Set HW RX filter: 0x607
[ 2817.331534] ath: phy3: Set HW RX filter: 0x417
[ 2817.331615] ath: phy3: Set channel: 2412 MHz width: 0
[ 2817.331754] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2817.396422] ath: phy3: Set channel: 5180 MHz width: 2
[ 2817.396559] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2817.600614] ath: phy3: Set channel: 2417 MHz width: 0
[ 2817.600751] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2817.665549] ath: phy3: Set channel: 2422 MHz width: 0
[ 2817.665683] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2817.726579] ath: phy3: Set channel: 5180 MHz width: 2
[ 2817.726719] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2817.930765] ath: phy3: Set channel: 2427 MHz width: 0
[ 2817.930894] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2817.995679] ath: phy3: Set channel: 2432 MHz width: 0
[ 2817.995820] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2818.056709] ath: phy3: Set channel: 5180 MHz width: 2
[ 2818.056851] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2818.260924] ath: phy3: Set channel: 2437 MHz width: 0
[ 2818.261063] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2818.325801] ath: phy3: Set channel: 5180 MHz width: 2
[ 2818.325939] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2818.529991] ath: phy3: Set channel: 2442 MHz width: 0
[ 2818.530133] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2818.594974] ath: phy3: Set channel: 2447 MHz width: 0
[ 2818.595109] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2818.656002] ath: phy3: Set channel: 5180 MHz width: 2
[ 2818.656133] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2818.860197] ath: phy3: Set channel: 2452 MHz width: 0
[ 2818.860343] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2818.925128] ath: phy3: Set channel: 2457 MHz width: 0
[ 2818.925260] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2818.986139] ath: phy3: Set channel: 5180 MHz width: 2
[ 2818.986304] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2819.190354] ath: phy3: Set channel: 2462 MHz width: 0
[ 2819.190497] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2819.255263] ath: phy3: Set channel: 5180 MHz width: 2
[ 2819.255417] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2819.459469] ath: phy3: Set channel: 2467 MHz width: 0
[ 2819.459614] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2819.575429] ath: phy3: Set channel: 5180 MHz width: 2
[ 2819.575566] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2819.779621] ath: phy3: Set channel: 2472 MHz width: 0
[ 2819.779762] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2819.895569] ath: phy3: Set channel: 5180 MHz width: 2
[ 2819.895708] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2820.099774] ath: phy3: Set channel: 5180 MHz width: 2
[ 2820.099917] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2820.214711] ath: phy3: Set channel: 5180 MHz width: 2
[ 2820.214882] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2820.418928] ath: phy3: Set channel: 5200 MHz width: 0
[ 2820.419071] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2820.534868] ath: phy3: Set channel: 5180 MHz width: 2
[ 2820.535004] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2820.739058] ath: phy3: Set channel: 5220 MHz width: 0
[ 2820.739199] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2820.855021] ath: phy3: Set channel: 5180 MHz width: 2
[ 2820.855160] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2821.059200] ath: phy3: Set channel: 5240 MHz width: 0
[ 2821.059334] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2821.175155] ath: phy3: Set channel: 5180 MHz width: 2
[ 2821.175292] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2821.379361] ath: phy3: Set channel: 5260 MHz width: 0
[ 2821.379505] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2821.495315] ath: phy3: Set channel: 5180 MHz width: 2
[ 2821.495451] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2821.699517] ath: phy3: Set channel: 5280 MHz width: 0
[ 2821.699664] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2821.815462] ath: phy3: Set channel: 5180 MHz width: 2
[ 2821.815600] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2822.019658] ath: phy3: Set channel: 5300 MHz width: 0
[ 2822.019801] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2822.135608] ath: phy3: Set channel: 5180 MHz width: 2
[ 2822.135745] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2822.339799] ath: phy3: Set channel: 5320 MHz width: 0
[ 2822.339942] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2822.455746] ath: phy3: Set channel: 5180 MHz width: 2
[ 2822.455905] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2822.659935] ath: phy3: Set channel: 5500 MHz width: 0
[ 2822.660072] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2822.775857] ath: phy3: Set channel: 5180 MHz width: 2
[ 2822.776001] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2822.980110] ath: phy3: Set channel: 5520 MHz width: 0
[ 2822.980252] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2823.096068] ath: phy3: Set channel: 5180 MHz width: 2
[ 2823.096216] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2823.300251] ath: phy3: Set channel: 5540 MHz width: 0
[ 2823.300393] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2823.416187] ath: phy3: Set channel: 5180 MHz width: 2
[ 2823.416350] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2823.620397] ath: phy3: Set channel: 5560 MHz width: 0
[ 2823.620541] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2823.736319] ath: phy3: Set channel: 5180 MHz width: 2
[ 2823.736459] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2823.940502] ath: phy3: Set channel: 5580 MHz width: 0
[ 2823.940650] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2824.056505] ath: phy3: Set channel: 5180 MHz width: 2
[ 2824.056655] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2824.260683] ath: phy3: Set channel: 5600 MHz width: 0
[ 2824.260824] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2824.376642] ath: phy3: Set channel: 5180 MHz width: 2
[ 2824.376778] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2824.580796] ath: phy3: Set channel: 5620 MHz width: 0
[ 2824.580941] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2824.696792] ath: phy3: Set channel: 5180 MHz width: 2
[ 2824.696928] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2824.900962] ath: phy3: Set channel: 5640 MHz width: 0
[ 2824.901099] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2825.016931] ath: phy3: Set channel: 5180 MHz width: 2
[ 2825.017069] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2825.221128] ath: phy3: Set channel: 5660 MHz width: 0
[ 2825.221270] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2825.337085] ath: phy3: Set channel: 5180 MHz width: 2
[ 2825.337222] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2825.541275] ath: phy3: Set channel: 5680 MHz width: 0
[ 2825.541420] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2825.657233] ath: phy3: Set channel: 5180 MHz width: 2
[ 2825.657369] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2825.861381] ath: phy3: Set channel: 5700 MHz width: 0
[ 2825.861525] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2825.977336] ath: phy3: Set channel: 5180 MHz width: 2
[ 2825.977482] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2825.982152] ath: phy3: Set HW RX filter: 0x607
[ 2867.044129] ath: phy3: Set HW Key
[ 2920.374005] ath: phy3: Set HW RX filter: 0x417
[ 2920.374029] ath: phy3: Set channel: 2412 MHz width: 0
[ 2920.374151] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2920.438956] ath: phy3: Set channel: 5180 MHz width: 2
[ 2920.439111] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2920.643345] ath: phy3: Set channel: 2417 MHz width: 0
[ 2920.643485] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2920.708099] ath: phy3: Set channel: 2422 MHz width: 0
[ 2920.708231] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2920.769130] ath: phy3: Set channel: 5180 MHz width: 2
[ 2920.769262] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2920.973464] ath: phy3: Set channel: 2427 MHz width: 0
[ 2920.973595] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2921.038243] ath: phy3: Set channel: 2432 MHz width: 0
[ 2921.038390] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2921.099265] ath: phy3: Set channel: 5180 MHz width: 2
[ 2921.099413] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2921.303631] ath: phy3: Set channel: 2437 MHz width: 0
[ 2921.303783] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2921.368410] ath: phy3: Set channel: 2442 MHz width: 0
[ 2921.368557] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2921.429419] ath: phy3: Set channel: 5180 MHz width: 2
[ 2921.429580] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2921.633794] ath: phy3: Set channel: 2447 MHz width: 0
[ 2921.633947] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2921.698536] ath: phy3: Set channel: 2452 MHz width: 0
[ 2921.698679] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2921.759573] ath: phy3: Set channel: 5180 MHz width: 2
[ 2921.759722] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2921.963929] ath: phy3: Set channel: 2457 MHz width: 0
[ 2921.964070] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2922.028708] ath: phy3: Set channel: 2462 MHz width: 0
[ 2922.028845] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2922.089737] ath: phy3: Set channel: 5180 MHz width: 2
[ 2922.089870] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2922.294073] ath: phy3: Set channel: 2467 MHz width: 0
[ 2922.294216] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2922.409884] ath: phy3: Set channel: 5180 MHz width: 2
[ 2922.410020] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2922.614144] ath: phy3: Set channel: 2472 MHz width: 0
[ 2922.614284] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2922.730036] ath: phy3: Set channel: 5180 MHz width: 2
[ 2922.730173] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2922.934385] ath: phy3: Set channel: 5180 MHz width: 2
[ 2922.934530] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2923.049186] ath: phy3: Set channel: 5180 MHz width: 2
[ 2923.049329] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2923.253536] ath: phy3: Set channel: 5200 MHz width: 0
[ 2923.253682] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2923.369280] ath: phy3: Set channel: 5180 MHz width: 2
[ 2923.369457] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2923.573666] ath: phy3: Set channel: 5220 MHz width: 0
[ 2923.573796] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2923.689474] ath: phy3: Set channel: 5180 MHz width: 2
[ 2923.689623] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2923.893870] ath: phy3: Set channel: 5240 MHz width: 0
[ 2923.894011] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2924.009613] ath: phy3: Set channel: 5180 MHz width: 2
[ 2924.009768] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2924.213848] ath: phy3: Set channel: 5260 MHz width: 0
[ 2924.213989] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2924.329771] ath: phy3: Set channel: 5180 MHz width: 2
[ 2924.329929] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2924.534092] ath: phy3: Set channel: 5280 MHz width: 0
[ 2924.534235] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2924.649916] ath: phy3: Set channel: 5180 MHz width: 2
[ 2924.650065] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2924.854255] ath: phy3: Set channel: 5300 MHz width: 0
[ 2924.854401] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2924.970064] ath: phy3: Set channel: 5180 MHz width: 2
[ 2924.970218] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2925.174412] ath: phy3: Set channel: 5320 MHz width: 0
[ 2925.174557] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2925.290208] ath: phy3: Set channel: 5180 MHz width: 2
[ 2925.290383] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2925.494554] ath: phy3: Set channel: 5500 MHz width: 0
[ 2925.494704] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2925.610370] ath: phy3: Set channel: 5180 MHz width: 2
[ 2925.610517] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2925.814711] ath: phy3: Set channel: 5520 MHz width: 0
[ 2925.814852] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2925.930523] ath: phy3: Set channel: 5180 MHz width: 2
[ 2925.930686] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2926.134879] ath: phy3: Set channel: 5540 MHz width: 0
[ 2926.135031] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2926.250648] ath: phy3: Set channel: 5180 MHz width: 2
[ 2926.250821] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2926.454981] ath: phy3: Set channel: 5560 MHz width: 0
[ 2926.455122] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2926.570803] ath: phy3: Set channel: 5180 MHz width: 2
[ 2926.570953] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2926.775177] ath: phy3: Set channel: 5580 MHz width: 0
[ 2926.775324] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2926.890960] ath: phy3: Set channel: 5180 MHz width: 2
[ 2926.891111] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2927.095274] ath: phy3: Set channel: 5600 MHz width: 0
[ 2927.095410] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2927.211103] ath: phy3: Set channel: 5180 MHz width: 2
[ 2927.211251] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2927.415450] ath: phy3: Set channel: 5620 MHz width: 0
[ 2927.415593] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2927.531250] ath: phy3: Set channel: 5180 MHz width: 2
[ 2927.531385] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2927.735600] ath: phy3: Set channel: 5640 MHz width: 0
[ 2927.735746] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2927.851403] ath: phy3: Set channel: 5180 MHz width: 2
[ 2927.851555] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2928.055752] ath: phy3: Set channel: 5660 MHz width: 0
[ 2928.055894] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2928.171542] ath: phy3: Set channel: 5180 MHz width: 2
[ 2928.171692] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2928.375869] ath: phy3: Set channel: 5680 MHz width: 0
[ 2928.376032] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2928.491690] ath: phy3: Set channel: 5180 MHz width: 2
[ 2928.491839] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2928.696048] ath: phy3: Set channel: 5700 MHz width: 0
[ 2928.696192] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2928.811847] ath: phy3: Set channel: 5180 MHz width: 2
[ 2928.811989] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2928.816485] ath: phy3: Set HW RX filter: 0x607
[ 3040.429312] ath: phy3: Set HW RX filter: 0x417
[ 3040.429322] ath: phy3: Set channel: 2412 MHz width: 0
[ 3040.429458] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 3040.494385] ath: phy3: Set channel: 5180 MHz width: 2
[ 3040.494526] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3040.698569] ath: phy3: Set channel: 2417 MHz width: 0
[ 3040.698706] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 3040.763514] ath: phy3: Set channel: 2422 MHz width: 0
[ 3040.763674] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 3040.824513] ath: phy3: Set channel: 5180 MHz width: 2
[ 3040.824655] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3041.028708] ath: phy3: Set channel: 2427 MHz width: 0
[ 3041.028848] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 3041.093659] ath: phy3: Set channel: 2432 MHz width: 0
[ 3041.093797] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 3041.154667] ath: phy3: Set channel: 5180 MHz width: 2
[ 3041.154814] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3041.358820] ath: phy3: Set channel: 2437 MHz width: 0
[ 3041.358956] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 3041.423758] ath: phy3: Set channel: 2442 MHz width: 0
[ 3041.423902] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 3041.484830] ath: phy3: Set channel: 5180 MHz width: 2
[ 3041.484972] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3041.689036] ath: phy3: Set channel: 2447 MHz width: 0
[ 3041.689170] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 3041.753909] ath: phy3: Set channel: 2452 MHz width: 0
[ 3041.754060] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 3041.814940] ath: phy3: Set channel: 5180 MHz width: 2
[ 3041.815077] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3042.019133] ath: phy3: Set channel: 2457 MHz width: 0
[ 3042.019278] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 3042.084062] ath: phy3: Set channel: 2462 MHz width: 0
[ 3042.084209] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 3042.145120] ath: phy3: Set channel: 5180 MHz width: 2
[ 3042.145267] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3042.349335] ath: phy3: Set channel: 2467 MHz width: 0
[ 3042.349488] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 3042.404150] ath: phy3: BB_WATCHDOG: Skipping interrupts
[ 3042.404290] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 0
[ 3042.465291] ath: phy3: Set channel: 5180 MHz width: 2
[ 3042.465429] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3042.669425] ath: phy3: Set channel: 2472 MHz width: 0
[ 3042.669556] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 3042.785385] ath: phy3: Set channel: 5180 MHz width: 2
[ 3042.785534] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3042.989619] ath: phy3: Set channel: 5180 MHz width: 2
[ 3042.989758] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3043.104587] ath: phy3: Set channel: 5180 MHz width: 2
[ 3043.104735] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3043.308771] ath: phy3: Set channel: 5200 MHz width: 0
[ 3043.308910] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 3043.424682] ath: phy3: Set channel: 5180 MHz width: 2
[ 3043.424830] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3043.628919] ath: phy3: Set channel: 5220 MHz width: 0
[ 3043.629052] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 3043.744829] ath: phy3: Set channel: 5180 MHz width: 2
[ 3043.744978] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3043.949024] ath: phy3: Set channel: 5240 MHz width: 0
[ 3043.949155] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 3044.065003] ath: phy3: Set channel: 5180 MHz width: 2
[ 3044.065177] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3044.269213] ath: phy3: Set channel: 5260 MHz width: 0
[ 3044.269355] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 3044.385181] ath: phy3: Set channel: 5180 MHz width: 2
[ 3044.385317] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3044.589356] ath: phy3: Set channel: 5280 MHz width: 0
[ 3044.589492] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 3044.705324] ath: phy3: Set channel: 5180 MHz width: 2
[ 3044.705461] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3044.909507] ath: phy3: Set channel: 5300 MHz width: 0
[ 3044.909643] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 3045.025445] ath: phy3: Set channel: 5180 MHz width: 2
[ 3045.025582] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3045.229600] ath: phy3: Set channel: 5320 MHz width: 0
[ 3045.229736] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 3045.345591] ath: phy3: Set channel: 5180 MHz width: 2
[ 3045.345733] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3045.549766] ath: phy3: Set channel: 5500 MHz width: 0
[ 3045.549915] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 3045.665769] ath: phy3: Set channel: 5180 MHz width: 2
[ 3045.665907] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3045.869940] ath: phy3: Set channel: 5520 MHz width: 0
[ 3045.870097] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 3045.985915] ath: phy3: Set channel: 5180 MHz width: 2
[ 3045.986053] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3046.190117] ath: phy3: Set channel: 5540 MHz width: 0
[ 3046.190262] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 3046.306064] ath: phy3: Set channel: 5180 MHz width: 2
[ 3046.306202] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3046.510186] ath: phy3: Set channel: 5560 MHz width: 0
[ 3046.510319] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 3046.626207] ath: phy3: Set channel: 5180 MHz width: 2
[ 3046.626343] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3046.830413] ath: phy3: Set channel: 5580 MHz width: 0
[ 3046.830557] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 3046.946359] ath: phy3: Set channel: 5180 MHz width: 2
[ 3046.946496] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3047.150568] ath: phy3: Set channel: 5600 MHz width: 0
[ 3047.150724] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 3047.266473] ath: phy3: Set channel: 5180 MHz width: 2
[ 3047.266627] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3047.470705] ath: phy3: Set channel: 5620 MHz width: 0
[ 3047.470856] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 3047.586687] ath: phy3: Set channel: 5180 MHz width: 2
[ 3047.586823] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3047.790843] ath: phy3: Set channel: 5640 MHz width: 0
[ 3047.790988] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 3047.906810] ath: phy3: Set channel: 5180 MHz width: 2
[ 3047.906967] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3048.110982] ath: phy3: Set channel: 5660 MHz width: 0
[ 3048.111128] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 3048.226952] ath: phy3: Set channel: 5180 MHz width: 2
[ 3048.227102] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3048.431150] ath: phy3: Set channel: 5680 MHz width: 0
[ 3048.431285] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 3048.547102] ath: phy3: Set channel: 5180 MHz width: 2
[ 3048.547241] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3048.751263] ath: phy3: Set channel: 5700 MHz width: 0
[ 3048.751402] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 3048.867282] ath: phy3: Set channel: 5180 MHz width: 2
[ 3048.867454] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3048.872053] ath: phy3: Set HW RX filter: 0x607
[ 3160.485230] ath: phy3: Set HW RX filter: 0x417
[ 3160.485255] ath: phy3: Set channel: 2412 MHz width: 0
[ 3160.485380] ath: phy3: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 3160.549783] ath: phy3: Set channel: 2417 MHz width: 0
[ 3160.549911] ath: phy3: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 3160.610817] ath: phy3: Set channel: 5180 MHz width: 2
[ 3160.610952] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3160.815181] ath: phy3: Set channel: 2422 MHz width: 0
[ 3160.815307] ath: phy3: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 3160.879920] ath: phy3: Set channel: 2427 MHz width: 0
[ 3160.880065] ath: phy3: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 3160.940948] ath: phy3: Set channel: 5180 MHz width: 2
[ 3160.941097] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3161.145291] ath: phy3: Set channel: 2432 MHz width: 0
[ 3161.145425] ath: phy3: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 3161.210116] ath: phy3: Set channel: 2437 MHz width: 0
[ 3161.210253] ath: phy3: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 3161.271121] ath: phy3: Set channel: 5180 MHz width: 2
[ 3161.271256] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3161.475437] ath: phy3: Set channel: 2442 MHz width: 0
[ 3161.475583] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 3161.540259] ath: phy3: Set channel: 5180 MHz width: 2
[ 3161.540394] ath: phy3: unsupported hw bitrate detected 0x1b using 1 Mbit
[ 3161.540414] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3161.744603] ath: phy3: Set channel: 2447 MHz width: 0
[ 3161.744748] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 3161.809370] ath: phy3: Set channel: 2452 MHz width: 0
[ 3161.809506] ath: phy3: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 3161.870398] ath: phy3: Set channel: 5180 MHz width: 2
[ 3161.870538] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3162.074741] ath: phy3: Set channel: 2457 MHz width: 0
[ 3162.074896] ath: phy3: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 3162.139510] ath: phy3: Set channel: 2462 MHz width: 0
[ 3162.139686] ath: phy3: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 3162.200538] ath: phy3: Set channel: 5180 MHz width: 2
[ 3162.200695] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3162.404852] ath: phy3: Set channel: 2467 MHz width: 0
[ 3162.404977] ath: phy3: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 3162.520680] ath: phy3: Set channel: 5180 MHz width: 2
[ 3162.520834] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3162.725011] ath: phy3: Set channel: 2472 MHz width: 0
[ 3162.725141] ath: phy3: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 3162.840826] ath: phy3: Set channel: 5180 MHz width: 2
[ 3162.840983] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3163.045128] ath: phy3: Set channel: 5180 MHz width: 2
[ 3163.045249] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3163.159993] ath: phy3: Set channel: 5180 MHz width: 2
[ 3163.160126] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3163.364337] ath: phy3: Set channel: 5200 MHz width: 0
[ 3163.364480] ath: phy3: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 3163.480140] ath: phy3: Set channel: 5180 MHz width: 2
[ 3163.480277] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3163.684561] ath: phy3: Set channel: 5220 MHz width: 0
[ 3163.684726] ath: phy3: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 3163.800272] ath: phy3: Set channel: 5180 MHz width: 2
[ 3163.800425] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3164.004530] ath: phy3: Set channel: 5240 MHz width: 0
[ 3164.004666] ath: phy3: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 3164.120436] ath: phy3: Set channel: 5180 MHz width: 2
[ 3164.120573] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3164.324694] ath: phy3: Set channel: 5260 MHz width: 0
[ 3164.324836] ath: phy3: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 3164.440581] ath: phy3: Set channel: 5180 MHz width: 2
[ 3164.440731] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3164.644945] ath: phy3: Set channel: 5280 MHz width: 0
[ 3164.645087] ath: phy3: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 3164.760734] ath: phy3: Set channel: 5180 MHz width: 2
[ 3164.760872] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3164.965045] ath: phy3: Set channel: 5300 MHz width: 0
[ 3164.965194] ath: phy3: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 3165.080865] ath: phy3: Set channel: 5180 MHz width: 2
[ 3165.081017] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3165.285222] ath: phy3: Set channel: 5320 MHz width: 0
[ 3165.285365] ath: phy3: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 3165.400973] ath: phy3: Set channel: 5180 MHz width: 2
[ 3165.401112] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3165.605349] ath: phy3: Set channel: 5500 MHz width: 0
[ 3165.605490] ath: phy3: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 3165.721178] ath: phy3: Set channel: 5180 MHz width: 2
[ 3165.721316] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3165.925522] ath: phy3: Set channel: 5520 MHz width: 0
[ 3165.925666] ath: phy3: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 3166.041264] ath: phy3: Set channel: 5180 MHz width: 2
[ 3166.041405] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3166.245569] ath: phy3: Set channel: 5540 MHz width: 0
[ 3166.245705] ath: phy3: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 3166.361456] ath: phy3: Set channel: 5180 MHz width: 2
[ 3166.361610] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3166.565817] ath: phy3: Set channel: 5560 MHz width: 0
[ 3166.565960] ath: phy3: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 3166.681603] ath: phy3: Set channel: 5180 MHz width: 2
[ 3166.681756] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3166.886022] ath: phy3: Set channel: 5580 MHz width: 0
[ 3166.886197] ath: phy3: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 3167.001766] ath: phy3: Set channel: 5180 MHz width: 2
[ 3167.001902] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3167.206119] ath: phy3: Set channel: 5600 MHz width: 0
[ 3167.206284] ath: phy3: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 3167.321911] ath: phy3: Set channel: 5180 MHz width: 2
[ 3167.322048] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3167.526345] ath: phy3: Set channel: 5620 MHz width: 0
[ 3167.526538] ath: phy3: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 3167.642046] ath: phy3: Set channel: 5180 MHz width: 2
[ 3167.642227] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3167.846386] ath: phy3: Set channel: 5640 MHz width: 0
[ 3167.846538] ath: phy3: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 3167.962200] ath: phy3: Set channel: 5180 MHz width: 2
[ 3167.962357] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3168.166549] ath: phy3: Set channel: 5660 MHz width: 0
[ 3168.166711] ath: phy3: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 3168.282357] ath: phy3: Set channel: 5180 MHz width: 2
[ 3168.282505] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3168.486704] ath: phy3: Set channel: 5680 MHz width: 0
[ 3168.486830] ath: phy3: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 3168.602488] ath: phy3: Set channel: 5180 MHz width: 2
[ 3168.602641] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3168.806854] ath: phy3: Set channel: 5700 MHz width: 0
[ 3168.807019] ath: phy3: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 3168.922649] ath: phy3: Set channel: 5180 MHz width: 2
[ 3168.922790] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3168.927295] ath: phy3: Set HW RX filter: 0x607
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 295 bytes
Desc: OpenPGP digital signature
Url : http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20140107/a7b48fcd/attachment-0001.pgp 

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-07 20:50       ` Oleksij Rempel
@ 2014-01-08  2:08         ` Sujith Manoharan
  2014-01-08  9:18           ` Oleksij Rempel
  2014-01-08  2:20         ` Sujith Manoharan
  1 sibling, 1 reply; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-08  2:08 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> Am 07.01.2014 17:26, schrieb Sujith Manoharan:
> > Oleksij Rempel wrote:
> >>> Does this happen a lot ?
> >>
> >> It depends on how intensively WiFi is used.
> >>
> >> See attachment
> >>
> >> [  657.383048] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
> >> [  657.703201] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
> > 
> > Can you load the driver with debug=0x200 (with latest wireless-testing) and
> > post the kernel log when the issue happens ?
> 
> looks like happens at scan time:
> [ 3161.475583] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
> [ 3161.540259] ath: phy3: Set channel: 5180 MHz width: 2
> [ 3161.540394] ath: phy3: unsupported hw bitrate detected 0x1b using 1 Mbit
> [ 3161.540414] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
> [ 3161.744603] ath: phy3: Set channel: 2447 MHz width: 0
> [ 3161.744748] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1

Yes, that was my suspicion.

Can you try this patch ?

diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
index 6d643ca..a638f3a 100644
--- a/drivers/net/wireless/ath/ath9k/recv.c
+++ b/drivers/net/wireless/ath/ath9k/recv.c
@@ -850,8 +850,9 @@ static int ath9k_process_rate(struct ath_common *common,
 	enum ieee80211_band band;
 	unsigned int i = 0;
 	struct ath_softc __maybe_unused *sc = common->priv;
+	struct ath_hw *ah = common->ah;
 
-	band = hw->conf.chandef.chan->band;
+	band = ah->curchan->chan->band;
 	sband = hw->wiphy->bands[band];
 
 	switch (hw->conf.chandef.width) {


Sujith

^ permalink raw reply related	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-07 20:50       ` Oleksij Rempel
  2014-01-08  2:08         ` Sujith Manoharan
@ 2014-01-08  2:20         ` Sujith Manoharan
  1 sibling, 0 replies; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-08  2:20 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> looks like happens at scan time:
> [ 3161.475583] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
> [ 3161.540259] ath: phy3: Set channel: 5180 MHz width: 2
> [ 3161.540394] ath: phy3: unsupported hw bitrate detected 0x1b using 1 Mbit
> [ 3161.540414] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
> [ 3161.744603] ath: phy3: Set channel: 2447 MHz width: 0
> [ 3161.744748] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
> 
> some time there are some BB_WATCHDOG warning too.

Sorry, the watchdog details are printed with the ATH_DBG_RESET level.
Can you post the log with debug=0x201, so we can see what signatures
the HW is generating ?

Sujith

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08  2:08         ` Sujith Manoharan
@ 2014-01-08  9:18           ` Oleksij Rempel
  2014-01-08 10:58             ` Sujith Manoharan
  2014-01-08 16:18             ` Sujith Manoharan
  0 siblings, 2 replies; 14+ messages in thread
From: Oleksij Rempel @ 2014-01-08  9:18 UTC (permalink / raw)
  To: ath9k-devel

Am 08.01.2014 03:08, schrieb Sujith Manoharan:
> Oleksij Rempel wrote:
>> Am 07.01.2014 17:26, schrieb Sujith Manoharan:
>>> Oleksij Rempel wrote:
>>>>> Does this happen a lot ?
>>>>
>>>> It depends on how intensively WiFi is used.
>>>>
>>>> See attachment
>>>>
>>>> [  657.383048] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
>>>> [  657.703201] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
>>>
>>> Can you load the driver with debug=0x200 (with latest wireless-testing) and
>>> post the kernel log when the issue happens ?
>>
>> looks like happens at scan time:
>> [ 3161.475583] ath: phy3: Reset to 2442 MHz, HT40: 0 fastcc: 1
>> [ 3161.540259] ath: phy3: Set channel: 5180 MHz width: 2
>> [ 3161.540394] ath: phy3: unsupported hw bitrate detected 0x1b using 1 Mbit
>> [ 3161.540414] ath: phy3: Reset to 5180 MHz, HT40: 1 fastcc: 0
>> [ 3161.744603] ath: phy3: Set channel: 2447 MHz width: 0
>> [ 3161.744748] ath: phy3: Reset to 2447 MHz, HT40: 0 fastcc: 1
> 
> Yes, that was my suspicion.
> 
> Can you try this patch ?
> 
> diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
> index 6d643ca..a638f3a 100644
> --- a/drivers/net/wireless/ath/ath9k/recv.c
> +++ b/drivers/net/wireless/ath/ath9k/recv.c
> @@ -850,8 +850,9 @@ static int ath9k_process_rate(struct ath_common *common,
>  	enum ieee80211_band band;
>  	unsigned int i = 0;
>  	struct ath_softc __maybe_unused *sc = common->priv;
> +	struct ath_hw *ah = common->ah;
>  
> -	band = hw->conf.chandef.chan->band;
> +	band = ah->curchan->chan->band;
>  	sband = hw->wiphy->bands[band];
>  
>  	switch (hw->conf.chandef.width) {

seems to be fixed with this change. thank you :)

in attachment is demsg for BB_WATCHDOG

-- 
Regards,
Oleksij
-------------- next part --------------
[ 2645.245014] ath: phy1: Set HW RX filter: 0x417
[ 2645.245029] ath: phy1: Set channel: 2412 MHz width: 0
[ 2645.245167] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2645.245184] ath: phy1: FastChannelChange for 5180 -> 2412
[ 2645.309779] ath: phy1: Set channel: 2417 MHz width: 0
[ 2645.309930] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2645.309940] ath: phy1: FastChannelChange for 2412 -> 2417
[ 2645.370802] ath: phy1: Set channel: 5180 MHz width: 2
[ 2645.370941] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2645.371604] ath: phy1: ah->misc_mode 0x10000004
[ 2645.375295] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2645.575019] ath: phy1: Set channel: 2422 MHz width: 0
[ 2645.575155] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2645.575169] ath: phy1: FastChannelChange for 5180 -> 2422
[ 2645.639754] ath: phy1: Set channel: 2427 MHz width: 0
[ 2645.639892] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2645.639903] ath: phy1: FastChannelChange for 2422 -> 2427
[ 2645.700705] ath: phy1: Set channel: 5180 MHz width: 2
[ 2645.700852] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2645.701482] ath: phy1: ah->misc_mode 0x10000004
[ 2645.705189] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2645.905035] ath: phy1: Set channel: 2432 MHz width: 0
[ 2645.905169] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2645.905183] ath: phy1: FastChannelChange for 5180 -> 2432
[ 2645.969708] ath: phy1: Set channel: 2437 MHz width: 0
[ 2645.969864] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2645.969876] ath: phy1: FastChannelChange for 2432 -> 2437
[ 2646.030679] ath: phy1: Set channel: 5180 MHz width: 2
[ 2646.030829] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2646.031501] ath: phy1: ah->misc_mode 0x10000004
[ 2646.035236] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2646.234960] ath: phy1: Set channel: 2442 MHz width: 0
[ 2646.235102] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2646.235118] ath: phy1: FastChannelChange for 5180 -> 2442
[ 2646.299699] ath: phy1: Set channel: 2447 MHz width: 0
[ 2646.299838] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2646.299849] ath: phy1: FastChannelChange for 2442 -> 2447
[ 2646.360717] ath: phy1: Set channel: 5180 MHz width: 2
[ 2646.360851] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2646.361522] ath: phy1: ah->misc_mode 0x10000004
[ 2646.365285] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2646.564983] ath: phy1: Set channel: 2452 MHz width: 0
[ 2646.565130] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2646.565142] ath: phy1: FastChannelChange for 5180 -> 2452
[ 2646.629714] ath: phy1: Set channel: 2457 MHz width: 0
[ 2646.629855] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2646.629866] ath: phy1: FastChannelChange for 2452 -> 2457
[ 2646.690768] ath: phy1: Set channel: 5180 MHz width: 2
[ 2646.690937] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2646.691621] ath: phy1: ah->misc_mode 0x10000004
[ 2646.695412] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2646.895043] ath: phy1: Set channel: 2462 MHz width: 0
[ 2646.895193] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2646.895211] ath: phy1: FastChannelChange for 5180 -> 2462
[ 2646.959765] ath: phy1: Set channel: 5180 MHz width: 2
[ 2646.959938] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2646.960610] ath: phy1: ah->misc_mode 0x10000004
[ 2646.964373] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2647.163939] ath: phy1: Set channel: 2467 MHz width: 0
[ 2647.164080] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2647.164095] ath: phy1: FastChannelChange for 5180 -> 2467
[ 2647.279748] ath: phy1: Set channel: 5180 MHz width: 2
[ 2647.279900] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2647.280577] ath: phy1: ah->misc_mode 0x10000004
[ 2647.284372] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2647.484004] ath: phy1: Set channel: 2472 MHz width: 0
[ 2647.484150] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2647.484167] ath: phy1: FastChannelChange for 5180 -> 2472
[ 2647.599784] ath: phy1: Set channel: 5180 MHz width: 2
[ 2647.599941] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2647.600622] ath: phy1: ah->misc_mode 0x10000004
[ 2647.604368] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2647.803908] ath: phy1: Set channel: 5180 MHz width: 2
[ 2647.804048] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2647.804705] ath: phy1: ah->misc_mode 0x10000004
[ 2647.808405] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2647.918727] ath: phy1: Set channel: 5180 MHz width: 2
[ 2647.918870] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2647.919517] ath: phy1: ah->misc_mode 0x10000004
[ 2647.923278] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2648.122998] ath: phy1: Set channel: 5200 MHz width: 0
[ 2648.123179] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2648.123198] ath: phy1: FastChannelChange for 5180 -> 5200
[ 2648.238699] ath: phy1: Set channel: 5180 MHz width: 2
[ 2648.238862] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2648.239541] ath: phy1: ah->misc_mode 0x10000004
[ 2648.243329] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2648.442995] ath: phy1: Set channel: 5220 MHz width: 0
[ 2648.443166] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2648.443186] ath: phy1: FastChannelChange for 5180 -> 5220
[ 2648.558678] ath: phy1: Set channel: 5180 MHz width: 2
[ 2648.558830] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2648.559497] ath: phy1: ah->misc_mode 0x10000004
[ 2648.563255] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2648.762973] ath: phy1: Set channel: 5240 MHz width: 0
[ 2648.763149] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2648.763170] ath: phy1: FastChannelChange for 5180 -> 5240
[ 2648.878674] ath: phy1: Set channel: 5180 MHz width: 2
[ 2648.878836] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2648.879517] ath: phy1: ah->misc_mode 0x10000004
[ 2648.883305] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2649.082934] ath: phy1: Set channel: 5260 MHz width: 0
[ 2649.083079] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2649.083095] ath: phy1: FastChannelChange for 5180 -> 5260
[ 2649.198653] ath: phy1: Set channel: 5180 MHz width: 2
[ 2649.198813] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2649.199490] ath: phy1: ah->misc_mode 0x10000004
[ 2649.203260] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2649.402911] ath: phy1: Set channel: 5280 MHz width: 0
[ 2649.403057] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2649.403073] ath: phy1: FastChannelChange for 5180 -> 5280
[ 2649.518701] ath: phy1: Set channel: 5180 MHz width: 2
[ 2649.518873] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2649.519562] ath: phy1: ah->misc_mode 0x10000004
[ 2649.523319] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2649.722921] ath: phy1: Set channel: 5300 MHz width: 0
[ 2649.723069] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2649.723084] ath: phy1: FastChannelChange for 5180 -> 5300
[ 2649.838690] ath: phy1: Set channel: 5180 MHz width: 2
[ 2649.838839] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2649.839503] ath: phy1: ah->misc_mode 0x10000004
[ 2649.843262] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2650.042906] ath: phy1: Set channel: 5320 MHz width: 0
[ 2650.043093] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2650.043114] ath: phy1: FastChannelChange for 5180 -> 5320
[ 2650.158618] ath: phy1: Set channel: 5180 MHz width: 2
[ 2650.158781] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2650.159465] ath: phy1: ah->misc_mode 0x10000004
[ 2650.163250] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2650.362871] ath: phy1: Set channel: 5500 MHz width: 0
[ 2650.363033] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2650.363052] ath: phy1: FastChannelChange for 5180 -> 5500
[ 2650.478588] ath: phy1: Set channel: 5180 MHz width: 2
[ 2650.478752] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2650.479426] ath: phy1: ah->misc_mode 0x10000004
[ 2650.483192] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2650.682878] ath: phy1: Set channel: 5520 MHz width: 0
[ 2650.683040] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2650.683058] ath: phy1: FastChannelChange for 5180 -> 5520
[ 2650.798545] ath: phy1: Set channel: 5180 MHz width: 2
[ 2650.798683] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2650.799345] ath: phy1: ah->misc_mode 0x10000004
[ 2650.803088] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2651.002782] ath: phy1: Set channel: 5540 MHz width: 0
[ 2651.002921] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2651.002936] ath: phy1: FastChannelChange for 5180 -> 5540
[ 2651.118541] ath: phy1: Set channel: 5180 MHz width: 2
[ 2651.118680] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2651.119342] ath: phy1: ah->misc_mode 0x10000004
[ 2651.123086] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2651.322805] ath: phy1: Set channel: 5560 MHz width: 0
[ 2651.322948] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2651.322964] ath: phy1: FastChannelChange for 5180 -> 5560
[ 2651.438535] ath: phy1: Set channel: 5180 MHz width: 2
[ 2651.438673] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2651.439343] ath: phy1: ah->misc_mode 0x10000004
[ 2651.443109] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2651.642864] ath: phy1: Set channel: 5580 MHz width: 0
[ 2651.643008] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2651.643023] ath: phy1: FastChannelChange for 5180 -> 5580
[ 2651.758573] ath: phy1: Set channel: 5180 MHz width: 2
[ 2651.758738] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2651.759412] ath: phy1: ah->misc_mode 0x10000004
[ 2651.763182] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2651.962777] ath: phy1: Set channel: 5600 MHz width: 0
[ 2651.962918] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2651.962935] ath: phy1: FastChannelChange for 5180 -> 5600
[ 2652.078518] ath: phy1: Set channel: 5180 MHz width: 2
[ 2652.078668] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2652.079338] ath: phy1: ah->misc_mode 0x10000004
[ 2652.083088] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2652.106600] ath: phy1: Set HW RX filter: 0x417
[ 2652.282828] ath: phy1: Set channel: 5620 MHz width: 0
[ 2652.282983] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2652.283001] ath: phy1: FastChannelChange for 5180 -> 5620
[ 2652.398625] ath: phy1: Set channel: 5180 MHz width: 2
[ 2652.398780] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2652.399470] ath: phy1: ah->misc_mode 0x10000004
[ 2652.403240] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2652.602818] ath: phy1: Set channel: 5640 MHz width: 0
[ 2652.602957] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2652.602972] ath: phy1: FastChannelChange for 5180 -> 5640
[ 2652.718529] ath: phy1: Set channel: 5180 MHz width: 2
[ 2652.718691] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2652.719362] ath: phy1: ah->misc_mode 0x10000004
[ 2652.723128] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2652.922735] ath: phy1: Set channel: 5660 MHz width: 0
[ 2652.922884] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2652.922901] ath: phy1: FastChannelChange for 5180 -> 5660
[ 2653.038485] ath: phy1: Set channel: 5180 MHz width: 2
[ 2653.038636] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2653.039307] ath: phy1: ah->misc_mode 0x10000004
[ 2653.043074] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2653.242777] ath: phy1: Set channel: 5680 MHz width: 0
[ 2653.242921] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2653.242937] ath: phy1: FastChannelChange for 5180 -> 5680
[ 2653.358566] ath: phy1: Set channel: 5180 MHz width: 2
[ 2653.358726] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2653.359425] ath: phy1: ah->misc_mode 0x10000004
[ 2653.363210] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2653.562747] ath: phy1: Set channel: 5700 MHz width: 0
[ 2653.562912] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2653.562932] ath: phy1: FastChannelChange for 5180 -> 5700
[ 2653.678502] ath: phy1: Set channel: 5180 MHz width: 2
[ 2653.678680] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2653.679434] ath: phy1: ah->misc_mode 0x10000004
[ 2653.683198] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2653.683297] ath: phy1: Set HW RX filter: 0x607
[ 2653.845828] ath: phy1: Set HW RX filter: 0x607
[ 2688.249284] ath: phy1: Set HW RX filter: 0x417
[ 2688.249327] ath: phy1: Set channel: 2412 MHz width: 0
[ 2688.249470] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2688.249487] ath: phy1: FastChannelChange for 5180 -> 2412
[ 2688.314136] ath: phy1: Set channel: 2417 MHz width: 0
[ 2688.314284] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2688.314295] ath: phy1: FastChannelChange for 2412 -> 2417
[ 2688.375134] ath: phy1: Set channel: 5180 MHz width: 2
[ 2688.375286] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2688.375960] ath: phy1: ah->misc_mode 0x10000004
[ 2688.379725] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2688.579416] ath: phy1: Set channel: 2422 MHz width: 0
[ 2688.579563] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2688.579579] ath: phy1: FastChannelChange for 5180 -> 2422
[ 2688.644102] ath: phy1: Set channel: 2427 MHz width: 0
[ 2688.644253] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2688.644264] ath: phy1: FastChannelChange for 2422 -> 2427
[ 2688.705109] ath: phy1: Set channel: 5180 MHz width: 2
[ 2688.705262] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2688.705934] ath: phy1: ah->misc_mode 0x10000004
[ 2688.709691] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2688.909462] ath: phy1: Set channel: 2432 MHz width: 0
[ 2688.909607] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2688.909625] ath: phy1: FastChannelChange for 5180 -> 2432
[ 2688.974108] ath: phy1: Set channel: 2437 MHz width: 0
[ 2688.974266] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2688.974279] ath: phy1: FastChannelChange for 2432 -> 2437
[ 2689.035083] ath: phy1: Set channel: 5180 MHz width: 2
[ 2689.035235] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2689.035908] ath: phy1: ah->misc_mode 0x10000004
[ 2689.039665] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2689.239371] ath: phy1: Set channel: 2442 MHz width: 0
[ 2689.239531] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2689.239550] ath: phy1: FastChannelChange for 5180 -> 2442
[ 2689.304100] ath: phy1: Set channel: 2447 MHz width: 0
[ 2689.304242] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2689.304253] ath: phy1: FastChannelChange for 2442 -> 2447
[ 2689.365100] ath: phy1: Set channel: 5180 MHz width: 2
[ 2689.365245] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2689.365892] ath: phy1: ah->misc_mode 0x10000004
[ 2689.369587] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2689.569424] ath: phy1: Set channel: 2452 MHz width: 0
[ 2689.569571] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2689.569589] ath: phy1: FastChannelChange for 5180 -> 2452
[ 2689.634074] ath: phy1: Set channel: 2457 MHz width: 0
[ 2689.634220] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2689.634231] ath: phy1: FastChannelChange for 2452 -> 2457
[ 2689.695076] ath: phy1: Set channel: 5180 MHz width: 2
[ 2689.695228] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2689.695891] ath: phy1: ah->misc_mode 0x10000004
[ 2689.699631] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2689.899422] ath: phy1: Set channel: 2462 MHz width: 0
[ 2689.899570] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2689.899587] ath: phy1: FastChannelChange for 5180 -> 2462
[ 2689.964112] ath: phy1: Set channel: 5180 MHz width: 2
[ 2689.964268] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2689.964939] ath: phy1: ah->misc_mode 0x10000004
[ 2689.968717] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2690.168338] ath: phy1: Set channel: 2467 MHz width: 0
[ 2690.168515] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2690.168534] ath: phy1: FastChannelChange for 5180 -> 2467
[ 2690.223270] ath: phy1: 
[ 2690.223270] ==== BB update: BB status=0x13000609 ====
[ 2690.223288] ath: phy1: ** BB state: wd=1 det=1 rdar=0 rOFDM=6 rCCK=0 tOFDM=0 tCCK=0 agc=3 src=1 **
[ 2690.223298] ath: phy1: ** BB WD cntl: cntl1=0xffff010d cntl2=0x00000004 **
[ 2690.223303] ath: phy1: ** BB mode: BB_gen_controls=0x01318bc0 **
[ 2690.223307] ath: phy1: ** BB busy times: rx_clear=0%, rx_frame=0%, tx_frame=0% **
[ 2690.223309] ath: phy1: ==== BB update: done ====
[ 2690.223309] 
[ 2690.223320] ath: phy1: BB_WATCHDOG: Skipping interrupts
[ 2690.223496] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 0
[ 2690.224276] ath: phy1: ah->misc_mode 0x10000004
[ 2690.228431] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2690.284050] ath: phy1: Set channel: 5180 MHz width: 2
[ 2690.284209] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2690.284886] ath: phy1: ah->misc_mode 0x10000004
[ 2690.288649] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2690.488328] ath: phy1: Set channel: 2472 MHz width: 0
[ 2690.488510] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2690.488530] ath: phy1: FastChannelChange for 5180 -> 2472
[ 2690.604035] ath: phy1: Set channel: 5180 MHz width: 2
[ 2690.604196] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2690.604878] ath: phy1: ah->misc_mode 0x10000004
[ 2690.608648] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2690.808349] ath: phy1: Set channel: 5180 MHz width: 2
[ 2690.808527] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2690.809219] ath: phy1: ah->misc_mode 0x10000004
[ 2690.813008] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2690.924091] ath: phy1: Set channel: 5180 MHz width: 2
[ 2690.924237] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2690.924888] ath: phy1: ah->misc_mode 0x10000004
[ 2690.928658] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2691.128363] ath: phy1: Set channel: 5200 MHz width: 0
[ 2691.128507] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2691.128524] ath: phy1: FastChannelChange for 5180 -> 5200
[ 2691.243991] ath: phy1: Set channel: 5180 MHz width: 2
[ 2691.244139] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2691.244810] ath: phy1: ah->misc_mode 0x10000004
[ 2691.248567] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2691.448274] ath: phy1: Set channel: 5220 MHz width: 0
[ 2691.448413] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2691.448427] ath: phy1: FastChannelChange for 5180 -> 5220
[ 2691.564069] ath: phy1: Set channel: 5180 MHz width: 2
[ 2691.564217] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2691.564880] ath: phy1: ah->misc_mode 0x10000004
[ 2691.568625] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2691.768289] ath: phy1: Set channel: 5240 MHz width: 0
[ 2691.768465] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2691.768486] ath: phy1: FastChannelChange for 5180 -> 5240
[ 2691.884003] ath: phy1: Set channel: 5180 MHz width: 2
[ 2691.884151] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2691.884818] ath: phy1: ah->misc_mode 0x10000004
[ 2691.888573] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2692.088292] ath: phy1: Set channel: 5260 MHz width: 0
[ 2692.088440] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2692.088456] ath: phy1: FastChannelChange for 5180 -> 5260
[ 2692.203945] ath: phy1: Set channel: 5180 MHz width: 2
[ 2692.204097] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2692.204758] ath: phy1: ah->misc_mode 0x10000004
[ 2692.208503] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2692.408259] ath: phy1: Set channel: 5280 MHz width: 0
[ 2692.408405] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2692.408420] ath: phy1: FastChannelChange for 5180 -> 5280
[ 2692.523997] ath: phy1: Set channel: 5180 MHz width: 2
[ 2692.524143] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2692.524805] ath: phy1: ah->misc_mode 0x10000004
[ 2692.528549] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2692.728221] ath: phy1: Set channel: 5300 MHz width: 0
[ 2692.728357] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2692.728372] ath: phy1: FastChannelChange for 5180 -> 5300
[ 2692.843956] ath: phy1: Set channel: 5180 MHz width: 2
[ 2692.844119] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2692.844791] ath: phy1: ah->misc_mode 0x10000004
[ 2692.848548] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2693.048226] ath: phy1: Set channel: 5320 MHz width: 0
[ 2693.048370] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2693.048387] ath: phy1: FastChannelChange for 5180 -> 5320
[ 2693.163997] ath: phy1: Set channel: 5180 MHz width: 2
[ 2693.164168] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2693.164867] ath: phy1: ah->misc_mode 0x10000004
[ 2693.168648] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2693.368272] ath: phy1: Set channel: 5500 MHz width: 0
[ 2693.368423] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2693.368441] ath: phy1: FastChannelChange for 5180 -> 5500
[ 2693.483945] ath: phy1: Set channel: 5180 MHz width: 2
[ 2693.484090] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2693.484757] ath: phy1: ah->misc_mode 0x10000004
[ 2693.488521] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2693.688238] ath: phy1: Set channel: 5520 MHz width: 0
[ 2693.688392] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2693.688409] ath: phy1: FastChannelChange for 5180 -> 5520
[ 2693.803905] ath: phy1: Set channel: 5180 MHz width: 2
[ 2693.804057] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2693.804732] ath: phy1: ah->misc_mode 0x10000004
[ 2693.808497] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2694.008218] ath: phy1: Set channel: 5540 MHz width: 0
[ 2694.008368] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2694.008385] ath: phy1: FastChannelChange for 5180 -> 5540
[ 2694.123975] ath: phy1: Set channel: 5180 MHz width: 2
[ 2694.124119] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2694.124803] ath: phy1: ah->misc_mode 0x10000004
[ 2694.128557] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2694.328247] ath: phy1: Set channel: 5560 MHz width: 0
[ 2694.328411] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2694.328429] ath: phy1: FastChannelChange for 5180 -> 5560
[ 2694.443892] ath: phy1: Set channel: 5180 MHz width: 2
[ 2694.444043] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2694.444705] ath: phy1: ah->misc_mode 0x10000004
[ 2694.448467] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2694.648200] ath: phy1: Set channel: 5580 MHz width: 0
[ 2694.648348] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2694.648365] ath: phy1: FastChannelChange for 5180 -> 5580
[ 2694.763899] ath: phy1: Set channel: 5180 MHz width: 2
[ 2694.764041] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2694.764694] ath: phy1: ah->misc_mode 0x10000004
[ 2694.768456] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2694.968248] ath: phy1: Set channel: 5600 MHz width: 0
[ 2694.968441] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2694.968471] ath: phy1: FastChannelChange for 5180 -> 5600
[ 2695.083874] ath: phy1: Set channel: 5180 MHz width: 2
[ 2695.084036] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2695.084705] ath: phy1: ah->misc_mode 0x10000004
[ 2695.088475] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2695.288135] ath: phy1: Set channel: 5620 MHz width: 0
[ 2695.288305] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2695.288323] ath: phy1: FastChannelChange for 5180 -> 5620
[ 2695.403937] ath: phy1: Set channel: 5180 MHz width: 2
[ 2695.404085] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2695.404764] ath: phy1: ah->misc_mode 0x10000004
[ 2695.408517] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2695.608226] ath: phy1: Set channel: 5640 MHz width: 0
[ 2695.608388] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2695.608406] ath: phy1: FastChannelChange for 5180 -> 5640
[ 2695.723879] ath: phy1: Set channel: 5180 MHz width: 2
[ 2695.724029] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2695.724686] ath: phy1: ah->misc_mode 0x10000004
[ 2695.728459] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2695.928210] ath: phy1: Set channel: 5660 MHz width: 0
[ 2695.928364] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2695.928381] ath: phy1: FastChannelChange for 5180 -> 5660
[ 2696.043845] ath: phy1: Set channel: 5180 MHz width: 2
[ 2696.044010] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2696.044677] ath: phy1: ah->misc_mode 0x10000004
[ 2696.048463] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2696.248103] ath: phy1: Set channel: 5680 MHz width: 0
[ 2696.248276] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2696.248294] ath: phy1: FastChannelChange for 5180 -> 5680
[ 2696.363808] ath: phy1: Set channel: 5180 MHz width: 2
[ 2696.363965] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2696.364635] ath: phy1: ah->misc_mode 0x10000004
[ 2696.368396] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2696.568077] ath: phy1: Set channel: 5700 MHz width: 0
[ 2696.568232] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2696.568252] ath: phy1: FastChannelChange for 5180 -> 5700
[ 2696.683811] ath: phy1: Set channel: 5180 MHz width: 2
[ 2696.683974] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2696.684635] ath: phy1: ah->misc_mode 0x10000004
[ 2696.688411] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2696.688514] ath: phy1: Set HW RX filter: 0x607
[ 2751.243897] ath: phy1: Set HW RX filter: 0x417
[ 2751.243942] ath: phy1: Set channel: 2412 MHz width: 0
[ 2751.244083] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2751.244100] ath: phy1: FastChannelChange for 5180 -> 2412
[ 2751.308682] ath: phy1: Set channel: 2417 MHz width: 0
[ 2751.308820] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2751.308829] ath: phy1: FastChannelChange for 2412 -> 2417
[ 2751.369683] ath: phy1: Set channel: 5180 MHz width: 2
[ 2751.369824] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2751.370488] ath: phy1: ah->misc_mode 0x10000004
[ 2751.374233] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2751.573954] ath: phy1: Set channel: 2422 MHz width: 0
[ 2751.574103] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2751.574118] ath: phy1: FastChannelChange for 5180 -> 2422
[ 2751.638669] ath: phy1: Set channel: 2427 MHz width: 0
[ 2751.638827] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2751.638838] ath: phy1: FastChannelChange for 2422 -> 2427
[ 2751.699666] ath: phy1: Set channel: 5180 MHz width: 2
[ 2751.699830] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2751.700503] ath: phy1: ah->misc_mode 0x10000004
[ 2751.704272] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2751.903893] ath: phy1: Set channel: 2432 MHz width: 0
[ 2751.904070] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2751.904089] ath: phy1: FastChannelChange for 5180 -> 2432
[ 2751.968629] ath: phy1: Set channel: 2437 MHz width: 0
[ 2751.968783] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2751.968794] ath: phy1: FastChannelChange for 2432 -> 2437
[ 2752.029654] ath: phy1: Set channel: 5180 MHz width: 2
[ 2752.029806] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2752.030479] ath: phy1: ah->misc_mode 0x10000004
[ 2752.034237] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2752.233926] ath: phy1: Set channel: 2442 MHz width: 0
[ 2752.234080] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2752.234098] ath: phy1: FastChannelChange for 5180 -> 2442
[ 2752.298641] ath: phy1: Set channel: 2447 MHz width: 0
[ 2752.298789] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2752.298799] ath: phy1: FastChannelChange for 2442 -> 2447
[ 2752.359628] ath: phy1: Set channel: 5180 MHz width: 2
[ 2752.359766] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2752.360427] ath: phy1: ah->misc_mode 0x10000004
[ 2752.364170] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2752.563912] ath: phy1: Set channel: 2452 MHz width: 0
[ 2752.564070] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2752.564089] ath: phy1: FastChannelChange for 5180 -> 2452
[ 2752.628625] ath: phy1: Set channel: 2457 MHz width: 0
[ 2752.628791] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2752.628803] ath: phy1: FastChannelChange for 2452 -> 2457
[ 2752.689625] ath: phy1: Set channel: 5180 MHz width: 2
[ 2752.689776] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2752.690425] ath: phy1: ah->misc_mode 0x10000004
[ 2752.694145] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2752.893908] ath: phy1: Set channel: 2462 MHz width: 0
[ 2752.894069] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2752.894089] ath: phy1: FastChannelChange for 5180 -> 2462
[ 2752.958641] ath: phy1: Set channel: 5180 MHz width: 2
[ 2752.958799] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2752.959462] ath: phy1: ah->misc_mode 0x10000004
[ 2752.963220] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2753.162904] ath: phy1: Set channel: 2467 MHz width: 0
[ 2753.163091] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2753.163111] ath: phy1: FastChannelChange for 5180 -> 2467
[ 2753.278598] ath: phy1: Set channel: 5180 MHz width: 2
[ 2753.278757] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2753.279430] ath: phy1: ah->misc_mode 0x10000004
[ 2753.283170] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2753.482891] ath: phy1: Set channel: 2472 MHz width: 0
[ 2753.483080] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2753.483098] ath: phy1: FastChannelChange for 5180 -> 2472
[ 2753.598587] ath: phy1: Set channel: 5180 MHz width: 2
[ 2753.598744] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2753.599419] ath: phy1: ah->misc_mode 0x10000004
[ 2753.603161] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2753.802878] ath: phy1: Set channel: 5180 MHz width: 2
[ 2753.803068] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2753.803800] ath: phy1: ah->misc_mode 0x10000004
[ 2753.807596] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2753.918582] ath: phy1: Set channel: 5180 MHz width: 2
[ 2753.918735] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2753.919385] ath: phy1: ah->misc_mode 0x10000004
[ 2753.923139] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2754.122854] ath: phy1: Set channel: 5200 MHz width: 0
[ 2754.123018] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2754.123038] ath: phy1: FastChannelChange for 5180 -> 5200
[ 2754.238580] ath: phy1: Set channel: 5180 MHz width: 2
[ 2754.238742] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2754.239417] ath: phy1: ah->misc_mode 0x10000004
[ 2754.243183] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2754.442844] ath: phy1: Set channel: 5220 MHz width: 0
[ 2754.443011] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2754.443031] ath: phy1: FastChannelChange for 5180 -> 5220
[ 2754.558559] ath: phy1: Set channel: 5180 MHz width: 2
[ 2754.558723] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2754.559391] ath: phy1: ah->misc_mode 0x10000004
[ 2754.563133] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2754.762876] ath: phy1: Set channel: 5240 MHz width: 0
[ 2754.763039] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2754.763058] ath: phy1: FastChannelChange for 5180 -> 5240
[ 2754.878539] ath: phy1: Set channel: 5180 MHz width: 2
[ 2754.878696] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2754.879361] ath: phy1: ah->misc_mode 0x10000004
[ 2754.883098] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2755.082822] ath: phy1: Set channel: 5260 MHz width: 0
[ 2755.083001] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2755.083021] ath: phy1: FastChannelChange for 5180 -> 5260
[ 2755.198529] ath: phy1: Set channel: 5180 MHz width: 2
[ 2755.198690] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2755.199363] ath: phy1: ah->misc_mode 0x10000004
[ 2755.203114] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2755.402809] ath: phy1: Set channel: 5280 MHz width: 0
[ 2755.402995] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2755.403014] ath: phy1: FastChannelChange for 5180 -> 5280
[ 2755.518518] ath: phy1: Set channel: 5180 MHz width: 2
[ 2755.518678] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2755.519350] ath: phy1: ah->misc_mode 0x10000004
[ 2755.523091] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2755.722777] ath: phy1: Set channel: 5300 MHz width: 0
[ 2755.722929] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2755.722946] ath: phy1: FastChannelChange for 5180 -> 5300
[ 2755.838585] ath: phy1: Set channel: 5180 MHz width: 2
[ 2755.838740] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2755.839425] ath: phy1: ah->misc_mode 0x10000004
[ 2755.843170] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2756.042780] ath: phy1: Set channel: 5320 MHz width: 0
[ 2756.042942] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2756.042959] ath: phy1: FastChannelChange for 5180 -> 5320
[ 2756.158588] ath: phy1: Set channel: 5180 MHz width: 2
[ 2756.158746] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2756.159427] ath: phy1: ah->misc_mode 0x10000004
[ 2756.163185] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2756.362778] ath: phy1: Set channel: 5500 MHz width: 0
[ 2756.362969] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2756.362989] ath: phy1: FastChannelChange for 5180 -> 5500
[ 2756.478475] ath: phy1: Set channel: 5180 MHz width: 2
[ 2756.478633] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2756.479302] ath: phy1: ah->misc_mode 0x10000004
[ 2756.483051] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2756.682801] ath: phy1: Set channel: 5520 MHz width: 0
[ 2756.682967] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2756.682987] ath: phy1: FastChannelChange for 5180 -> 5520
[ 2756.798462] ath: phy1: Set channel: 5180 MHz width: 2
[ 2756.798621] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2756.799291] ath: phy1: ah->misc_mode 0x10000004
[ 2756.803038] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2757.002744] ath: phy1: Set channel: 5540 MHz width: 0
[ 2757.002896] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2757.002914] ath: phy1: FastChannelChange for 5180 -> 5540
[ 2757.118548] ath: phy1: Set channel: 5180 MHz width: 2
[ 2757.118703] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2757.119393] ath: phy1: ah->misc_mode 0x10000004
[ 2757.123154] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2757.322744] ath: phy1: Set channel: 5560 MHz width: 0
[ 2757.322912] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2757.322932] ath: phy1: FastChannelChange for 5180 -> 5560
[ 2757.438445] ath: phy1: Set channel: 5180 MHz width: 2
[ 2757.438608] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2757.439276] ath: phy1: ah->misc_mode 0x10000004
[ 2757.443027] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2757.642775] ath: phy1: Set channel: 5580 MHz width: 0
[ 2757.642945] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2757.642965] ath: phy1: FastChannelChange for 5180 -> 5580
[ 2757.758429] ath: phy1: Set channel: 5180 MHz width: 2
[ 2757.758589] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2757.759258] ath: phy1: ah->misc_mode 0x10000004
[ 2757.763001] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2757.962748] ath: phy1: Set channel: 5600 MHz width: 0
[ 2757.962920] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2757.962940] ath: phy1: FastChannelChange for 5180 -> 5600
[ 2758.078431] ath: phy1: Set channel: 5180 MHz width: 2
[ 2758.078594] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2758.079264] ath: phy1: ah->misc_mode 0x10000004
[ 2758.083023] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2758.282715] ath: phy1: Set channel: 5620 MHz width: 0
[ 2758.282881] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2758.282900] ath: phy1: FastChannelChange for 5180 -> 5620
[ 2758.398408] ath: phy1: Set channel: 5180 MHz width: 2
[ 2758.398567] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2758.399241] ath: phy1: ah->misc_mode 0x10000004
[ 2758.402987] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2758.602705] ath: phy1: Set channel: 5640 MHz width: 0
[ 2758.602873] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2758.602892] ath: phy1: FastChannelChange for 5180 -> 5640
[ 2758.718385] ath: phy1: Set channel: 5180 MHz width: 2
[ 2758.718541] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2758.719210] ath: phy1: ah->misc_mode 0x10000004
[ 2758.722962] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2758.922683] ath: phy1: Set channel: 5660 MHz width: 0
[ 2758.922848] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2758.922867] ath: phy1: FastChannelChange for 5180 -> 5660
[ 2759.038377] ath: phy1: Set channel: 5180 MHz width: 2
[ 2759.038540] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2759.039213] ath: phy1: ah->misc_mode 0x10000004
[ 2759.042961] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2759.242661] ath: phy1: Set channel: 5680 MHz width: 0
[ 2759.242813] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2759.242830] ath: phy1: FastChannelChange for 5180 -> 5680
[ 2759.358457] ath: phy1: Set channel: 5180 MHz width: 2
[ 2759.358616] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2759.359319] ath: phy1: ah->misc_mode 0x10000004
[ 2759.363076] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2759.562588] ath: phy1: Set channel: 5700 MHz width: 0
[ 2759.562731] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2759.562745] ath: phy1: FastChannelChange for 5180 -> 5700
[ 2759.678431] ath: phy1: Set channel: 5180 MHz width: 2
[ 2759.678588] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2759.679320] ath: phy1: ah->misc_mode 0x10000004
[ 2759.683063] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2759.683161] ath: phy1: Set HW RX filter: 0x607
[ 2774.360971] ath: phy1: Set HW Key
[ 2834.238066] ath: phy1: Set HW RX filter: 0x417
[ 2834.238095] ath: phy1: Set channel: 2412 MHz width: 0
[ 2834.238239] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2834.238260] ath: phy1: FastChannelChange for 5180 -> 2412
[ 2834.303449] ath: phy1: Set channel: 5180 MHz width: 2
[ 2834.303605] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2834.304279] ath: phy1: ah->misc_mode 0x10000004
[ 2834.308034] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2834.507730] ath: phy1: Set channel: 2417 MHz width: 0
[ 2834.507870] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2834.507888] ath: phy1: FastChannelChange for 5180 -> 2417
[ 2834.572434] ath: phy1: Set channel: 2422 MHz width: 0
[ 2834.572594] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2834.572607] ath: phy1: FastChannelChange for 2417 -> 2422
[ 2834.633431] ath: phy1: Set channel: 5180 MHz width: 2
[ 2834.633589] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2834.634260] ath: phy1: ah->misc_mode 0x10000004
[ 2834.638020] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2834.837725] ath: phy1: Set channel: 2427 MHz width: 0
[ 2834.837878] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2834.837897] ath: phy1: FastChannelChange for 5180 -> 2427
[ 2834.902428] ath: phy1: Set channel: 2432 MHz width: 0
[ 2834.902573] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2834.902584] ath: phy1: FastChannelChange for 2427 -> 2432
[ 2834.963422] ath: phy1: Set channel: 5180 MHz width: 2
[ 2834.963576] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2834.964261] ath: phy1: ah->misc_mode 0x10000004
[ 2834.968018] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2835.167731] ath: phy1: Set channel: 2437 MHz width: 0
[ 2835.167884] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2835.167903] ath: phy1: FastChannelChange for 5180 -> 2437
[ 2835.232432] ath: phy1: Set channel: 2442 MHz width: 0
[ 2835.232593] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2835.232606] ath: phy1: FastChannelChange for 2437 -> 2442
[ 2835.293396] ath: phy1: Set channel: 5180 MHz width: 2
[ 2835.293546] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2835.294215] ath: phy1: ah->misc_mode 0x10000004
[ 2835.297954] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2835.497717] ath: phy1: Set channel: 2447 MHz width: 0
[ 2835.497875] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2835.497894] ath: phy1: FastChannelChange for 5180 -> 2447
[ 2835.562405] ath: phy1: Set channel: 2452 MHz width: 0
[ 2835.562564] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2835.562576] ath: phy1: FastChannelChange for 2447 -> 2452
[ 2835.623412] ath: phy1: Set channel: 5180 MHz width: 2
[ 2835.623567] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2835.624232] ath: phy1: ah->misc_mode 0x10000004
[ 2835.627958] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2835.827713] ath: phy1: Set channel: 2457 MHz width: 0
[ 2835.827881] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2835.827901] ath: phy1: FastChannelChange for 5180 -> 2457
[ 2835.892398] ath: phy1: Set channel: 2462 MHz width: 0
[ 2835.892551] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2835.892563] ath: phy1: FastChannelChange for 2457 -> 2462
[ 2835.953423] ath: phy1: Set channel: 5180 MHz width: 2
[ 2835.953571] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2835.954241] ath: phy1: ah->misc_mode 0x10000004
[ 2835.958020] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2836.157701] ath: phy1: Set channel: 2467 MHz width: 0
[ 2836.157859] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2836.157877] ath: phy1: FastChannelChange for 5180 -> 2467
[ 2836.273400] ath: phy1: Set channel: 5180 MHz width: 2
[ 2836.273558] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2836.274230] ath: phy1: ah->misc_mode 0x10000004
[ 2836.277998] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2836.477673] ath: phy1: Set channel: 2472 MHz width: 0
[ 2836.477817] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2836.477833] ath: phy1: FastChannelChange for 5180 -> 2472
[ 2836.593432] ath: phy1: Set channel: 5180 MHz width: 2
[ 2836.593590] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2836.594277] ath: phy1: ah->misc_mode 0x10000004
[ 2836.598042] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2836.797663] ath: phy1: Set channel: 5180 MHz width: 2
[ 2836.797830] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2836.798542] ath: phy1: ah->misc_mode 0x10000004
[ 2836.802358] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2836.913356] ath: phy1: Set channel: 5180 MHz width: 2
[ 2836.913510] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2836.914164] ath: phy1: ah->misc_mode 0x10000004
[ 2836.917930] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2837.117641] ath: phy1: Set channel: 5200 MHz width: 0
[ 2837.117806] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2837.117825] ath: phy1: FastChannelChange for 5180 -> 5200
[ 2837.233347] ath: phy1: Set channel: 5180 MHz width: 2
[ 2837.233509] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2837.234187] ath: phy1: ah->misc_mode 0x10000004
[ 2837.237970] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2837.437620] ath: phy1: Set channel: 5220 MHz width: 0
[ 2837.437784] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2837.437803] ath: phy1: FastChannelChange for 5180 -> 5220
[ 2837.553337] ath: phy1: Set channel: 5180 MHz width: 2
[ 2837.553502] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2837.554182] ath: phy1: ah->misc_mode 0x10000004
[ 2837.557971] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2837.757616] ath: phy1: Set channel: 5240 MHz width: 0
[ 2837.757781] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2837.757802] ath: phy1: FastChannelChange for 5180 -> 5240
[ 2837.873318] ath: phy1: Set channel: 5180 MHz width: 2
[ 2837.873481] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2837.874160] ath: phy1: ah->misc_mode 0x10000004
[ 2837.877951] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2838.077608] ath: phy1: Set channel: 5260 MHz width: 0
[ 2838.077770] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2838.077785] ath: phy1: FastChannelChange for 5180 -> 5260
[ 2838.193308] ath: phy1: Set channel: 5180 MHz width: 2
[ 2838.193469] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2838.194147] ath: phy1: ah->misc_mode 0x10000004
[ 2838.197925] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2838.397626] ath: phy1: Set channel: 5280 MHz width: 0
[ 2838.397797] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2838.397817] ath: phy1: FastChannelChange for 5180 -> 5280
[ 2838.513290] ath: phy1: Set channel: 5180 MHz width: 2
[ 2838.513450] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2838.514126] ath: phy1: ah->misc_mode 0x10000004
[ 2838.517883] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2838.717596] ath: phy1: Set channel: 5300 MHz width: 0
[ 2838.717771] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2838.717791] ath: phy1: FastChannelChange for 5180 -> 5300
[ 2838.833290] ath: phy1: Set channel: 5180 MHz width: 2
[ 2838.833452] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2838.834132] ath: phy1: ah->misc_mode 0x10000004
[ 2838.837914] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2839.037613] ath: phy1: Set channel: 5320 MHz width: 0
[ 2839.037798] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2839.037819] ath: phy1: FastChannelChange for 5180 -> 5320
[ 2839.153275] ath: phy1: Set channel: 5180 MHz width: 2
[ 2839.153439] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2839.154118] ath: phy1: ah->misc_mode 0x10000004
[ 2839.157905] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2839.357607] ath: phy1: Set channel: 5500 MHz width: 0
[ 2839.357793] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2839.357812] ath: phy1: FastChannelChange for 5180 -> 5500
[ 2839.473264] ath: phy1: Set channel: 5180 MHz width: 2
[ 2839.473426] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2839.474108] ath: phy1: ah->misc_mode 0x10000004
[ 2839.477893] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2839.677595] ath: phy1: Set channel: 5520 MHz width: 0
[ 2839.677773] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2839.677795] ath: phy1: FastChannelChange for 5180 -> 5520
[ 2839.793243] ath: phy1: Set channel: 5180 MHz width: 2
[ 2839.793407] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2839.794088] ath: phy1: ah->misc_mode 0x10000004
[ 2839.797873] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2839.997574] ath: phy1: Set channel: 5540 MHz width: 0
[ 2839.997740] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2839.997759] ath: phy1: FastChannelChange for 5180 -> 5540
[ 2840.113224] ath: phy1: Set channel: 5180 MHz width: 2
[ 2840.113385] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2840.114059] ath: phy1: ah->misc_mode 0x10000004
[ 2840.117829] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2840.317540] ath: phy1: Set channel: 5560 MHz width: 0
[ 2840.317709] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2840.317727] ath: phy1: FastChannelChange for 5180 -> 5560
[ 2840.433302] ath: phy1: Set channel: 5180 MHz width: 2
[ 2840.433460] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2840.434153] ath: phy1: ah->misc_mode 0x10000004
[ 2840.437927] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2840.637549] ath: phy1: Set channel: 5580 MHz width: 0
[ 2840.637719] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2840.637739] ath: phy1: FastChannelChange for 5180 -> 5580
[ 2840.753214] ath: phy1: Set channel: 5180 MHz width: 2
[ 2840.753377] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2840.754058] ath: phy1: ah->misc_mode 0x10000004
[ 2840.757838] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2840.957562] ath: phy1: Set channel: 5600 MHz width: 0
[ 2840.957715] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2840.957732] ath: phy1: FastChannelChange for 5180 -> 5600
[ 2841.073270] ath: phy1: Set channel: 5180 MHz width: 2
[ 2841.073427] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2841.074117] ath: phy1: ah->misc_mode 0x10000004
[ 2841.077882] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2841.277486] ath: phy1: Set channel: 5620 MHz width: 0
[ 2841.277637] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2841.277654] ath: phy1: FastChannelChange for 5180 -> 5620
[ 2841.393264] ath: phy1: Set channel: 5180 MHz width: 2
[ 2841.393426] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2841.394137] ath: phy1: ah->misc_mode 0x10000004
[ 2841.397915] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2841.597531] ath: phy1: Set channel: 5640 MHz width: 0
[ 2841.597705] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2841.597726] ath: phy1: FastChannelChange for 5180 -> 5640
[ 2841.713166] ath: phy1: Set channel: 5180 MHz width: 2
[ 2841.713326] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2841.714003] ath: phy1: ah->misc_mode 0x10000004
[ 2841.717764] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2841.917492] ath: phy1: Set channel: 5660 MHz width: 0
[ 2841.917671] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2841.917692] ath: phy1: FastChannelChange for 5180 -> 5660
[ 2842.033143] ath: phy1: Set channel: 5180 MHz width: 2
[ 2842.033308] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2842.033989] ath: phy1: ah->misc_mode 0x10000004
[ 2842.037766] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2842.237434] ath: phy1: Set channel: 5680 MHz width: 0
[ 2842.237603] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2842.237621] ath: phy1: FastChannelChange for 5180 -> 5680
[ 2842.353212] ath: phy1: Set channel: 5180 MHz width: 2
[ 2842.353367] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2842.354058] ath: phy1: ah->misc_mode 0x10000004
[ 2842.357833] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2842.557439] ath: phy1: Set channel: 5700 MHz width: 0
[ 2842.557613] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2842.557631] ath: phy1: FastChannelChange for 5180 -> 5700
[ 2842.673217] ath: phy1: Set channel: 5180 MHz width: 2
[ 2842.673401] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2842.674130] ath: phy1: ah->misc_mode 0x10000004
[ 2842.677902] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2842.678008] ath: phy1: Set HW RX filter: 0x607
[ 2937.236491] ath: phy1: Set HW RX filter: 0x417
[ 2937.236846] ath: phy1: Set channel: 2412 MHz width: 0
[ 2937.236985] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 2937.237005] ath: phy1: FastChannelChange for 5180 -> 2412
[ 2937.301449] ath: phy1: Set channel: 5180 MHz width: 2
[ 2937.301602] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2937.302267] ath: phy1: ah->misc_mode 0x10000004
[ 2937.306003] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2937.505745] ath: phy1: Set channel: 2417 MHz width: 0
[ 2937.505910] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 2937.505929] ath: phy1: FastChannelChange for 5180 -> 2417
[ 2937.570447] ath: phy1: Set channel: 2422 MHz width: 0
[ 2937.570608] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 2937.570621] ath: phy1: FastChannelChange for 2417 -> 2422
[ 2937.631456] ath: phy1: Set channel: 5180 MHz width: 2
[ 2937.631616] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2937.632295] ath: phy1: ah->misc_mode 0x10000004
[ 2937.636115] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2937.835766] ath: phy1: Set channel: 2427 MHz width: 0
[ 2937.835922] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 2937.835939] ath: phy1: FastChannelChange for 5180 -> 2427
[ 2937.900439] ath: phy1: Set channel: 2432 MHz width: 0
[ 2937.900593] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 2937.900606] ath: phy1: FastChannelChange for 2427 -> 2432
[ 2937.961476] ath: phy1: Set channel: 5180 MHz width: 2
[ 2937.961632] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2937.962307] ath: phy1: ah->misc_mode 0x10000004
[ 2937.966096] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2938.165695] ath: phy1: Set channel: 2437 MHz width: 0
[ 2938.165862] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 2938.165882] ath: phy1: FastChannelChange for 5180 -> 2437
[ 2938.230401] ath: phy1: Set channel: 2442 MHz width: 0
[ 2938.230563] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 2938.230577] ath: phy1: FastChannelChange for 2437 -> 2442
[ 2938.291424] ath: phy1: Set channel: 5180 MHz width: 2
[ 2938.291581] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2938.292256] ath: phy1: ah->misc_mode 0x10000004
[ 2938.296030] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2938.495676] ath: phy1: Set channel: 2447 MHz width: 0
[ 2938.495829] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 2938.495847] ath: phy1: FastChannelChange for 5180 -> 2447
[ 2938.560410] ath: phy1: Set channel: 2452 MHz width: 0
[ 2938.560573] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 2938.560585] ath: phy1: FastChannelChange for 2447 -> 2452
[ 2938.621380] ath: phy1: Set channel: 5180 MHz width: 2
[ 2938.621532] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2938.622205] ath: phy1: ah->misc_mode 0x10000004
[ 2938.625974] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2938.825616] ath: phy1: Set channel: 2457 MHz width: 0
[ 2938.825780] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 2938.825796] ath: phy1: FastChannelChange for 5180 -> 2457
[ 2938.890395] ath: phy1: Set channel: 2462 MHz width: 0
[ 2938.890537] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 2938.890548] ath: phy1: FastChannelChange for 2457 -> 2462
[ 2938.951390] ath: phy1: Set channel: 5180 MHz width: 2
[ 2938.951537] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2938.952184] ath: phy1: ah->misc_mode 0x10000004
[ 2938.955910] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2939.155671] ath: phy1: Set channel: 2467 MHz width: 0
[ 2939.155815] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 2939.155832] ath: phy1: FastChannelChange for 5180 -> 2467
[ 2939.271417] ath: phy1: Set channel: 5180 MHz width: 2
[ 2939.271564] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2939.272239] ath: phy1: ah->misc_mode 0x10000004
[ 2939.276021] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2939.475644] ath: phy1: Set channel: 2472 MHz width: 0
[ 2939.475782] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 2939.475799] ath: phy1: FastChannelChange for 5180 -> 2472
[ 2939.591453] ath: phy1: Set channel: 5180 MHz width: 2
[ 2939.591602] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2939.592273] ath: phy1: ah->misc_mode 0x10000004
[ 2939.596014] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2939.795685] ath: phy1: Set channel: 5180 MHz width: 2
[ 2939.795848] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2939.796552] ath: phy1: ah->misc_mode 0x10000004
[ 2939.800341] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2939.911340] ath: phy1: Set channel: 5180 MHz width: 2
[ 2939.911489] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2939.912125] ath: phy1: ah->misc_mode 0x10000004
[ 2939.915869] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2940.115667] ath: phy1: Set channel: 5200 MHz width: 0
[ 2940.115832] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 2940.115851] ath: phy1: FastChannelChange for 5180 -> 5200
[ 2940.231326] ath: phy1: Set channel: 5180 MHz width: 2
[ 2940.231480] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2940.232135] ath: phy1: ah->misc_mode 0x10000004
[ 2940.235880] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2940.435636] ath: phy1: Set channel: 5220 MHz width: 0
[ 2940.435798] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 2940.435816] ath: phy1: FastChannelChange for 5180 -> 5220
[ 2940.551316] ath: phy1: Set channel: 5180 MHz width: 2
[ 2940.551469] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2940.552122] ath: phy1: ah->misc_mode 0x10000004
[ 2940.555863] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2940.755619] ath: phy1: Set channel: 5240 MHz width: 0
[ 2940.755785] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 2940.755806] ath: phy1: FastChannelChange for 5180 -> 5240
[ 2940.871300] ath: phy1: Set channel: 5180 MHz width: 2
[ 2940.871449] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2940.872104] ath: phy1: ah->misc_mode 0x10000004
[ 2940.875851] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2941.075576] ath: phy1: Set channel: 5260 MHz width: 0
[ 2941.075730] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 2941.075747] ath: phy1: FastChannelChange for 5180 -> 5260
[ 2941.191359] ath: phy1: Set channel: 5180 MHz width: 2
[ 2941.191504] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2941.192153] ath: phy1: ah->misc_mode 0x10000004
[ 2941.195870] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2941.395611] ath: phy1: Set channel: 5280 MHz width: 0
[ 2941.395786] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 2941.395806] ath: phy1: FastChannelChange for 5180 -> 5280
[ 2941.511293] ath: phy1: Set channel: 5180 MHz width: 2
[ 2941.511445] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2941.512097] ath: phy1: ah->misc_mode 0x10000004
[ 2941.515801] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2941.715606] ath: phy1: Set channel: 5300 MHz width: 0
[ 2941.715783] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 2941.715800] ath: phy1: FastChannelChange for 5180 -> 5300
[ 2941.831375] ath: phy1: Set channel: 5180 MHz width: 2
[ 2941.831527] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2941.832210] ath: phy1: ah->misc_mode 0x10000004
[ 2941.835945] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2942.035532] ath: phy1: Set channel: 5320 MHz width: 0
[ 2942.035677] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 2942.035695] ath: phy1: FastChannelChange for 5180 -> 5320
[ 2942.151279] ath: phy1: Set channel: 5180 MHz width: 2
[ 2942.151418] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2942.152070] ath: phy1: ah->misc_mode 0x10000004
[ 2942.155779] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2942.355542] ath: phy1: Set channel: 5500 MHz width: 0
[ 2942.355682] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 2942.355700] ath: phy1: FastChannelChange for 5180 -> 5500
[ 2942.471341] ath: phy1: Set channel: 5180 MHz width: 2
[ 2942.471500] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2942.472180] ath: phy1: ah->misc_mode 0x10000004
[ 2942.475907] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2942.675527] ath: phy1: Set channel: 5520 MHz width: 0
[ 2942.675664] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 2942.675679] ath: phy1: FastChannelChange for 5180 -> 5520
[ 2942.791318] ath: phy1: Set channel: 5180 MHz width: 2
[ 2942.791489] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2942.792197] ath: phy1: ah->misc_mode 0x10000004
[ 2942.795913] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2942.995544] ath: phy1: Set channel: 5540 MHz width: 0
[ 2942.995703] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 2942.995722] ath: phy1: FastChannelChange for 5180 -> 5540
[ 2943.111217] ath: phy1: Set channel: 5180 MHz width: 2
[ 2943.111370] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2943.112024] ath: phy1: ah->misc_mode 0x10000004
[ 2943.115738] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2943.315530] ath: phy1: Set channel: 5560 MHz width: 0
[ 2943.315695] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 2943.315714] ath: phy1: FastChannelChange for 5180 -> 5560
[ 2943.431208] ath: phy1: Set channel: 5180 MHz width: 2
[ 2943.431362] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2943.432021] ath: phy1: ah->misc_mode 0x10000004
[ 2943.435739] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2943.635512] ath: phy1: Set channel: 5580 MHz width: 0
[ 2943.635679] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 2943.635699] ath: phy1: FastChannelChange for 5180 -> 5580
[ 2943.751189] ath: phy1: Set channel: 5180 MHz width: 2
[ 2943.751341] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2943.751994] ath: phy1: ah->misc_mode 0x10000004
[ 2943.755712] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2943.955534] ath: phy1: Set channel: 5600 MHz width: 0
[ 2943.955695] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 2943.955712] ath: phy1: FastChannelChange for 5180 -> 5600
[ 2944.071270] ath: phy1: Set channel: 5180 MHz width: 2
[ 2944.071421] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2944.072097] ath: phy1: ah->misc_mode 0x10000004
[ 2944.075816] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2944.275473] ath: phy1: Set channel: 5620 MHz width: 0
[ 2944.275639] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 2944.275656] ath: phy1: FastChannelChange for 5180 -> 5620
[ 2944.391253] ath: phy1: Set channel: 5180 MHz width: 2
[ 2944.391402] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2944.392057] ath: phy1: ah->misc_mode 0x10000004
[ 2944.395790] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2944.595483] ath: phy1: Set channel: 5640 MHz width: 0
[ 2944.595645] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 2944.595663] ath: phy1: FastChannelChange for 5180 -> 5640
[ 2944.711144] ath: phy1: Set channel: 5180 MHz width: 2
[ 2944.711297] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2944.711954] ath: phy1: ah->misc_mode 0x10000004
[ 2944.715660] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2944.915467] ath: phy1: Set channel: 5660 MHz width: 0
[ 2944.915633] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 2944.915652] ath: phy1: FastChannelChange for 5180 -> 5660
[ 2945.031135] ath: phy1: Set channel: 5180 MHz width: 2
[ 2945.031290] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2945.031947] ath: phy1: ah->misc_mode 0x10000004
[ 2945.035661] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2945.235442] ath: phy1: Set channel: 5680 MHz width: 0
[ 2945.235601] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 2945.235620] ath: phy1: FastChannelChange for 5180 -> 5680
[ 2945.351111] ath: phy1: Set channel: 5180 MHz width: 2
[ 2945.351261] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2945.351911] ath: phy1: ah->misc_mode 0x10000004
[ 2945.355617] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2945.555451] ath: phy1: Set channel: 5700 MHz width: 0
[ 2945.555620] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 2945.555639] ath: phy1: FastChannelChange for 5180 -> 5700
[ 2945.671088] ath: phy1: Set channel: 5180 MHz width: 2
[ 2945.671246] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 2945.671906] ath: phy1: ah->misc_mode 0x10000004
[ 2945.675618] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 2945.675712] ath: phy1: Set HW RX filter: 0x607
[ 3057.231508] ath: phy1: Set HW RX filter: 0x417
[ 3057.231540] ath: phy1: Set channel: 2412 MHz width: 0
[ 3057.231712] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 3057.231731] ath: phy1: FastChannelChange for 5180 -> 2412
[ 3057.296786] ath: phy1: Set channel: 5180 MHz width: 2
[ 3057.296945] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3057.297619] ath: phy1: ah->misc_mode 0x10000004
[ 3057.301384] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3057.501069] ath: phy1: Set channel: 2417 MHz width: 0
[ 3057.501233] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 3057.501252] ath: phy1: FastChannelChange for 5180 -> 2417
[ 3057.565787] ath: phy1: Set channel: 2422 MHz width: 0
[ 3057.565951] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 3057.565965] ath: phy1: FastChannelChange for 2417 -> 2422
[ 3057.626780] ath: phy1: Set channel: 5180 MHz width: 2
[ 3057.626945] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3057.627626] ath: phy1: ah->misc_mode 0x10000004
[ 3057.631423] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3057.831081] ath: phy1: Set channel: 2427 MHz width: 0
[ 3057.831245] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 3057.831265] ath: phy1: FastChannelChange for 5180 -> 2427
[ 3057.895750] ath: phy1: Set channel: 2432 MHz width: 0
[ 3057.895908] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 3057.895919] ath: phy1: FastChannelChange for 2427 -> 2432
[ 3057.956803] ath: phy1: Set channel: 5180 MHz width: 2
[ 3057.956957] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3057.957632] ath: phy1: ah->misc_mode 0x10000004
[ 3057.961422] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3058.161062] ath: phy1: Set channel: 2437 MHz width: 0
[ 3058.161212] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 3058.161231] ath: phy1: FastChannelChange for 5180 -> 2437
[ 3058.225777] ath: phy1: Set channel: 2442 MHz width: 0
[ 3058.225948] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 3058.225960] ath: phy1: FastChannelChange for 2437 -> 2442
[ 3058.286733] ath: phy1: Set channel: 5180 MHz width: 2
[ 3058.286892] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3058.287567] ath: phy1: ah->misc_mode 0x10000004
[ 3058.291334] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3058.491033] ath: phy1: Set channel: 2447 MHz width: 0
[ 3058.491188] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 3058.491207] ath: phy1: FastChannelChange for 5180 -> 2447
[ 3058.555723] ath: phy1: Set channel: 2452 MHz width: 0
[ 3058.555874] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 3058.555886] ath: phy1: FastChannelChange for 2447 -> 2452
[ 3058.616730] ath: phy1: Set channel: 5180 MHz width: 2
[ 3058.616893] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3058.617579] ath: phy1: ah->misc_mode 0x10000004
[ 3058.621354] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3058.821019] ath: phy1: Set channel: 2457 MHz width: 0
[ 3058.821182] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 3058.821201] ath: phy1: FastChannelChange for 5180 -> 2457
[ 3058.885732] ath: phy1: Set channel: 2462 MHz width: 0
[ 3058.885890] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 3058.885904] ath: phy1: FastChannelChange for 2457 -> 2462
[ 3058.946735] ath: phy1: Set channel: 5180 MHz width: 2
[ 3058.946888] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3058.947553] ath: phy1: ah->misc_mode 0x10000004
[ 3058.951282] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3059.151020] ath: phy1: Set channel: 2467 MHz width: 0
[ 3059.151188] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 3059.151207] ath: phy1: FastChannelChange for 5180 -> 2467
[ 3059.266720] ath: phy1: Set channel: 5180 MHz width: 2
[ 3059.266879] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3059.267548] ath: phy1: ah->misc_mode 0x10000004
[ 3059.271290] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3059.470988] ath: phy1: Set channel: 2472 MHz width: 0
[ 3059.471164] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 3059.471183] ath: phy1: FastChannelChange for 5180 -> 2472
[ 3059.586721] ath: phy1: Set channel: 5180 MHz width: 2
[ 3059.586876] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3059.587543] ath: phy1: ah->misc_mode 0x10000004
[ 3059.591292] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3059.791064] ath: phy1: Set channel: 5180 MHz width: 2
[ 3059.791227] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3059.791926] ath: phy1: ah->misc_mode 0x10000004
[ 3059.795706] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3059.906672] ath: phy1: Set channel: 5180 MHz width: 2
[ 3059.906817] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3059.907454] ath: phy1: ah->misc_mode 0x10000004
[ 3059.911184] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3060.110916] ath: phy1: Set channel: 5200 MHz width: 0
[ 3060.111055] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 3060.111070] ath: phy1: FastChannelChange for 5180 -> 5200
[ 3060.226650] ath: phy1: Set channel: 5180 MHz width: 2
[ 3060.226797] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3060.227462] ath: phy1: ah->misc_mode 0x10000004
[ 3060.231195] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3060.431011] ath: phy1: Set channel: 5220 MHz width: 0
[ 3060.431148] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 3060.431165] ath: phy1: FastChannelChange for 5180 -> 5220
[ 3060.546673] ath: phy1: Set channel: 5180 MHz width: 2
[ 3060.546816] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3060.547471] ath: phy1: ah->misc_mode 0x10000004
[ 3060.551199] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3060.750926] ath: phy1: Set channel: 5240 MHz width: 0
[ 3060.751062] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 3060.751077] ath: phy1: FastChannelChange for 5180 -> 5240
[ 3060.866713] ath: phy1: Set channel: 5180 MHz width: 2
[ 3060.866879] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3060.867573] ath: phy1: ah->misc_mode 0x10000004
[ 3060.871317] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3061.070885] ath: phy1: Set channel: 5260 MHz width: 0
[ 3061.071023] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 3061.071038] ath: phy1: FastChannelChange for 5180 -> 5260
[ 3061.186643] ath: phy1: Set channel: 5180 MHz width: 2
[ 3061.186771] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3061.187451] ath: phy1: ah->misc_mode 0x10000004
[ 3061.191169] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3061.390886] ath: phy1: Set channel: 5280 MHz width: 0
[ 3061.391025] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 3061.391039] ath: phy1: FastChannelChange for 5180 -> 5280
[ 3061.506612] ath: phy1: Set channel: 5180 MHz width: 2
[ 3061.506741] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3061.507445] ath: phy1: ah->misc_mode 0x10000004
[ 3061.511167] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3061.710861] ath: phy1: Set channel: 5300 MHz width: 0
[ 3061.710996] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 3061.711010] ath: phy1: FastChannelChange for 5180 -> 5300
[ 3061.826674] ath: phy1: Set channel: 5180 MHz width: 2
[ 3061.826838] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3061.827543] ath: phy1: ah->misc_mode 0x10000004
[ 3061.831300] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3062.030813] ath: phy1: Set channel: 5320 MHz width: 0
[ 3062.030950] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 3062.030965] ath: phy1: FastChannelChange for 5180 -> 5320
[ 3062.146607] ath: phy1: Set channel: 5180 MHz width: 2
[ 3062.146733] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3062.147378] ath: phy1: ah->misc_mode 0x10000004
[ 3062.151105] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3062.350874] ath: phy1: Set channel: 5500 MHz width: 0
[ 3062.351013] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 3062.351029] ath: phy1: FastChannelChange for 5180 -> 5500
[ 3062.466650] ath: phy1: Set channel: 5180 MHz width: 2
[ 3062.466815] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3062.467497] ath: phy1: ah->misc_mode 0x10000004
[ 3062.471245] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3062.670864] ath: phy1: Set channel: 5520 MHz width: 0
[ 3062.671001] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 3062.671017] ath: phy1: FastChannelChange for 5180 -> 5520
[ 3062.786581] ath: phy1: Set channel: 5180 MHz width: 2
[ 3062.786710] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3062.787345] ath: phy1: ah->misc_mode 0x10000004
[ 3062.791064] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3062.990860] ath: phy1: Set channel: 5540 MHz width: 0
[ 3062.990991] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 3062.991005] ath: phy1: FastChannelChange for 5180 -> 5540
[ 3063.106545] ath: phy1: Set channel: 5180 MHz width: 2
[ 3063.106677] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3063.107314] ath: phy1: ah->misc_mode 0x10000004
[ 3063.111061] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3063.310850] ath: phy1: Set channel: 5560 MHz width: 0
[ 3063.311030] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 3063.311049] ath: phy1: FastChannelChange for 5180 -> 5560
[ 3063.426537] ath: phy1: Set channel: 5180 MHz width: 2
[ 3063.426689] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3063.427344] ath: phy1: ah->misc_mode 0x10000004
[ 3063.431087] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3063.630827] ath: phy1: Set channel: 5580 MHz width: 0
[ 3063.630996] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 3063.631014] ath: phy1: FastChannelChange for 5180 -> 5580
[ 3063.746522] ath: phy1: Set channel: 5180 MHz width: 2
[ 3063.746676] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3063.747336] ath: phy1: ah->misc_mode 0x10000004
[ 3063.751078] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3063.950836] ath: phy1: Set channel: 5600 MHz width: 0
[ 3063.950966] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 3063.950982] ath: phy1: FastChannelChange for 5180 -> 5600
[ 3064.066587] ath: phy1: Set channel: 5180 MHz width: 2
[ 3064.066721] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3064.067355] ath: phy1: ah->misc_mode 0x10000004
[ 3064.071069] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3064.270801] ath: phy1: Set channel: 5620 MHz width: 0
[ 3064.270952] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 3064.270971] ath: phy1: FastChannelChange for 5180 -> 5620
[ 3064.386455] ath: phy1: Set channel: 5180 MHz width: 2
[ 3064.386609] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3064.387265] ath: phy1: ah->misc_mode 0x10000004
[ 3064.391000] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3064.590793] ath: phy1: Set channel: 5640 MHz width: 0
[ 3064.590938] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 3064.590956] ath: phy1: FastChannelChange for 5180 -> 5640
[ 3064.706470] ath: phy1: Set channel: 5180 MHz width: 2
[ 3064.706620] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3064.707273] ath: phy1: ah->misc_mode 0x10000004
[ 3064.711012] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3064.910770] ath: phy1: Set channel: 5660 MHz width: 0
[ 3064.910910] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 3064.910923] ath: phy1: FastChannelChange for 5180 -> 5660
[ 3065.026521] ath: phy1: Set channel: 5180 MHz width: 2
[ 3065.026662] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3065.027300] ath: phy1: ah->misc_mode 0x10000004
[ 3065.031017] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3065.230810] ath: phy1: Set channel: 5680 MHz width: 0
[ 3065.230943] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 3065.230959] ath: phy1: FastChannelChange for 5180 -> 5680
[ 3065.346478] ath: phy1: Set channel: 5180 MHz width: 2
[ 3065.346609] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3065.347255] ath: phy1: ah->misc_mode 0x10000004
[ 3065.350963] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3065.550739] ath: phy1: Set channel: 5700 MHz width: 0
[ 3065.550879] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 3065.550893] ath: phy1: FastChannelChange for 5180 -> 5700
[ 3065.666547] ath: phy1: Set channel: 5180 MHz width: 2
[ 3065.666700] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3065.667391] ath: phy1: ah->misc_mode 0x10000004
[ 3065.671147] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3065.671246] ath: phy1: Set HW RX filter: 0x607
[ 3177.225312] ath: phy1: Set HW RX filter: 0x417
[ 3177.225359] ath: phy1: Set channel: 2412 MHz width: 0
[ 3177.225521] ath: phy1: Reset to 2412 MHz, HT40: 0 fastcc: 1
[ 3177.225538] ath: phy1: FastChannelChange for 5180 -> 2412
[ 3177.290125] ath: phy1: Set channel: 2417 MHz width: 0
[ 3177.290287] ath: phy1: Reset to 2417 MHz, HT40: 0 fastcc: 1
[ 3177.290301] ath: phy1: FastChannelChange for 2412 -> 2417
[ 3177.351124] ath: phy1: Set channel: 5180 MHz width: 2
[ 3177.351281] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3177.351951] ath: phy1: ah->misc_mode 0x10000004
[ 3177.355715] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3177.555399] ath: phy1: Set channel: 2422 MHz width: 0
[ 3177.555545] ath: phy1: Reset to 2422 MHz, HT40: 0 fastcc: 1
[ 3177.555563] ath: phy1: FastChannelChange for 5180 -> 2422
[ 3177.620115] ath: phy1: Set channel: 2427 MHz width: 0
[ 3177.620273] ath: phy1: Reset to 2427 MHz, HT40: 0 fastcc: 1
[ 3177.620286] ath: phy1: FastChannelChange for 2422 -> 2427
[ 3177.681121] ath: phy1: Set channel: 5180 MHz width: 2
[ 3177.681299] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3177.681977] ath: phy1: ah->misc_mode 0x10000004
[ 3177.685770] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3177.885449] ath: phy1: Set channel: 2432 MHz width: 0
[ 3177.885617] ath: phy1: Reset to 2432 MHz, HT40: 0 fastcc: 1
[ 3177.885637] ath: phy1: FastChannelChange for 5180 -> 2432
[ 3177.950097] ath: phy1: Set channel: 2437 MHz width: 0
[ 3177.950261] ath: phy1: Reset to 2437 MHz, HT40: 0 fastcc: 1
[ 3177.950274] ath: phy1: FastChannelChange for 2432 -> 2437
[ 3178.011106] ath: phy1: Set channel: 5180 MHz width: 2
[ 3178.011265] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3178.011942] ath: phy1: ah->misc_mode 0x10000004
[ 3178.015713] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3178.215386] ath: phy1: Set channel: 2442 MHz width: 0
[ 3178.215542] ath: phy1: Reset to 2442 MHz, HT40: 0 fastcc: 1
[ 3178.215560] ath: phy1: FastChannelChange for 5180 -> 2442
[ 3178.280118] ath: phy1: Set channel: 2447 MHz width: 0
[ 3178.280279] ath: phy1: Reset to 2447 MHz, HT40: 0 fastcc: 1
[ 3178.280292] ath: phy1: FastChannelChange for 2442 -> 2447
[ 3178.341067] ath: phy1: Set channel: 5180 MHz width: 2
[ 3178.341222] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3178.341895] ath: phy1: ah->misc_mode 0x10000004
[ 3178.345652] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3178.545364] ath: phy1: Set channel: 2452 MHz width: 0
[ 3178.545520] ath: phy1: Reset to 2452 MHz, HT40: 0 fastcc: 1
[ 3178.545537] ath: phy1: FastChannelChange for 5180 -> 2452
[ 3178.610060] ath: phy1: Set channel: 2457 MHz width: 0
[ 3178.610214] ath: phy1: Reset to 2457 MHz, HT40: 0 fastcc: 1
[ 3178.610226] ath: phy1: FastChannelChange for 2452 -> 2457
[ 3178.671062] ath: phy1: Set channel: 5180 MHz width: 2
[ 3178.671226] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3178.671905] ath: phy1: ah->misc_mode 0x10000004
[ 3178.675663] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3178.875393] ath: phy1: Set channel: 2462 MHz width: 0
[ 3178.875571] ath: phy1: Reset to 2462 MHz, HT40: 0 fastcc: 1
[ 3178.875591] ath: phy1: FastChannelChange for 5180 -> 2462
[ 3178.940086] ath: phy1: Set channel: 5180 MHz width: 2
[ 3178.940236] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3178.940904] ath: phy1: ah->misc_mode 0x10000004
[ 3178.944660] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3179.144350] ath: phy1: Set channel: 2467 MHz width: 0
[ 3179.144517] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
[ 3179.144536] ath: phy1: FastChannelChange for 5180 -> 2467
[ 3179.199262] ath: phy1: 
[ 3179.199262] ==== BB update: BB status=0x13000609 ====
[ 3179.199279] ath: phy1: ** BB state: wd=1 det=1 rdar=0 rOFDM=6 rCCK=0 tOFDM=0 tCCK=0 agc=3 src=1 **
[ 3179.199287] ath: phy1: ** BB WD cntl: cntl1=0xffff010d cntl2=0x00000004 **
[ 3179.199292] ath: phy1: ** BB mode: BB_gen_controls=0x01318bc0 **
[ 3179.199295] ath: phy1: ** BB busy times: rx_clear=0%, rx_frame=0%, tx_frame=0% **
[ 3179.199298] ath: phy1: ==== BB update: done ====
[ 3179.199298] 
[ 3179.199306] ath: phy1: BB_WATCHDOG: Skipping interrupts
[ 3179.199479] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 0
[ 3179.200233] ath: phy1: ah->misc_mode 0x10000004
[ 3179.204393] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3179.260043] ath: phy1: Set channel: 5180 MHz width: 2
[ 3179.260194] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3179.260859] ath: phy1: ah->misc_mode 0x10000004
[ 3179.264597] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3179.464332] ath: phy1: Set channel: 2472 MHz width: 0
[ 3179.464491] ath: phy1: Reset to 2472 MHz, HT40: 0 fastcc: 1
[ 3179.464510] ath: phy1: FastChannelChange for 5180 -> 2472
[ 3179.580082] ath: phy1: Set channel: 5180 MHz width: 2
[ 3179.580235] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3179.580898] ath: phy1: ah->misc_mode 0x10000004
[ 3179.584657] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3179.784394] ath: phy1: Set channel: 5180 MHz width: 2
[ 3179.784539] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3179.785240] ath: phy1: ah->misc_mode 0x10000004
[ 3179.789026] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3179.900105] ath: phy1: Set channel: 5180 MHz width: 2
[ 3179.900260] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3179.900926] ath: phy1: ah->misc_mode 0x10000004
[ 3179.904683] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3180.104330] ath: phy1: Set channel: 5200 MHz width: 0
[ 3180.104508] ath: phy1: Reset to 5200 MHz, HT40: 0 fastcc: 1
[ 3180.104528] ath: phy1: FastChannelChange for 5180 -> 5200
[ 3180.220011] ath: phy1: Set channel: 5180 MHz width: 2
[ 3180.220173] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3180.220846] ath: phy1: ah->misc_mode 0x10000004
[ 3180.224589] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3180.424263] ath: phy1: Set channel: 5220 MHz width: 0
[ 3180.424434] ath: phy1: Reset to 5220 MHz, HT40: 0 fastcc: 1
[ 3180.424452] ath: phy1: FastChannelChange for 5180 -> 5220
[ 3180.540074] ath: phy1: Set channel: 5180 MHz width: 2
[ 3180.540224] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3180.540905] ath: phy1: ah->misc_mode 0x10000004
[ 3180.544658] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3180.744309] ath: phy1: Set channel: 5240 MHz width: 0
[ 3180.744484] ath: phy1: Reset to 5240 MHz, HT40: 0 fastcc: 1
[ 3180.744501] ath: phy1: FastChannelChange for 5180 -> 5240
[ 3180.859990] ath: phy1: Set channel: 5180 MHz width: 2
[ 3180.860150] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3180.860819] ath: phy1: ah->misc_mode 0x10000004
[ 3180.864558] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3181.064265] ath: phy1: Set channel: 5260 MHz width: 0
[ 3181.064425] ath: phy1: Reset to 5260 MHz, HT40: 0 fastcc: 1
[ 3181.064445] ath: phy1: FastChannelChange for 5180 -> 5260
[ 3181.179970] ath: phy1: Set channel: 5180 MHz width: 2
[ 3181.180131] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3181.180805] ath: phy1: ah->misc_mode 0x10000004
[ 3181.184549] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3181.384252] ath: phy1: Set channel: 5280 MHz width: 0
[ 3181.384434] ath: phy1: Reset to 5280 MHz, HT40: 0 fastcc: 1
[ 3181.384452] ath: phy1: FastChannelChange for 5180 -> 5280
[ 3181.499954] ath: phy1: Set channel: 5180 MHz width: 2
[ 3181.500118] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3181.500792] ath: phy1: ah->misc_mode 0x10000004
[ 3181.504540] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3181.704241] ath: phy1: Set channel: 5300 MHz width: 0
[ 3181.704388] ath: phy1: Reset to 5300 MHz, HT40: 0 fastcc: 1
[ 3181.704403] ath: phy1: FastChannelChange for 5180 -> 5300
[ 3181.819937] ath: phy1: Set channel: 5180 MHz width: 2
[ 3181.820088] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3181.820746] ath: phy1: ah->misc_mode 0x10000004
[ 3181.824480] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3182.024312] ath: phy1: Set channel: 5320 MHz width: 0
[ 3182.024484] ath: phy1: Reset to 5320 MHz, HT40: 0 fastcc: 1
[ 3182.024502] ath: phy1: FastChannelChange for 5180 -> 5320
[ 3182.139932] ath: phy1: Set channel: 5180 MHz width: 2
[ 3182.140095] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3182.140762] ath: phy1: ah->misc_mode 0x10000004
[ 3182.144520] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3182.344231] ath: phy1: Set channel: 5500 MHz width: 0
[ 3182.344392] ath: phy1: Reset to 5500 MHz, HT40: 0 fastcc: 1
[ 3182.344410] ath: phy1: FastChannelChange for 5180 -> 5500
[ 3182.459913] ath: phy1: Set channel: 5180 MHz width: 2
[ 3182.460071] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3182.460741] ath: phy1: ah->misc_mode 0x10000004
[ 3182.464485] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3182.664209] ath: phy1: Set channel: 5520 MHz width: 0
[ 3182.664372] ath: phy1: Reset to 5520 MHz, HT40: 0 fastcc: 1
[ 3182.664391] ath: phy1: FastChannelChange for 5180 -> 5520
[ 3182.779906] ath: phy1: Set channel: 5180 MHz width: 2
[ 3182.780068] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3182.780738] ath: phy1: ah->misc_mode 0x10000004
[ 3182.784485] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3182.984089] ath: phy1: Set channel: 5540 MHz width: 0
[ 3182.984238] ath: phy1: Reset to 5540 MHz, HT40: 0 fastcc: 1
[ 3182.984254] ath: phy1: FastChannelChange for 5180 -> 5540
[ 3183.099989] ath: phy1: Set channel: 5180 MHz width: 2
[ 3183.100145] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3183.100834] ath: phy1: ah->misc_mode 0x10000004
[ 3183.104600] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3183.304199] ath: phy1: Set channel: 5560 MHz width: 0
[ 3183.304361] ath: phy1: Reset to 5560 MHz, HT40: 0 fastcc: 1
[ 3183.304381] ath: phy1: FastChannelChange for 5180 -> 5560
[ 3183.419881] ath: phy1: Set channel: 5180 MHz width: 2
[ 3183.420039] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3183.420713] ath: phy1: ah->misc_mode 0x10000004
[ 3183.424467] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3183.624183] ath: phy1: Set channel: 5580 MHz width: 0
[ 3183.624350] ath: phy1: Reset to 5580 MHz, HT40: 0 fastcc: 1
[ 3183.624369] ath: phy1: FastChannelChange for 5180 -> 5580
[ 3183.739860] ath: phy1: Set channel: 5180 MHz width: 2
[ 3183.740021] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3183.740695] ath: phy1: ah->misc_mode 0x10000004
[ 3183.744438] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3183.944199] ath: phy1: Set channel: 5600 MHz width: 0
[ 3183.944353] ath: phy1: Reset to 5600 MHz, HT40: 0 fastcc: 1
[ 3183.944372] ath: phy1: FastChannelChange for 5180 -> 5600
[ 3184.059944] ath: phy1: Set channel: 5180 MHz width: 2
[ 3184.060109] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3184.060803] ath: phy1: ah->misc_mode 0x10000004
[ 3184.064565] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3184.264170] ath: phy1: Set channel: 5620 MHz width: 0
[ 3184.264334] ath: phy1: Reset to 5620 MHz, HT40: 0 fastcc: 1
[ 3184.264353] ath: phy1: FastChannelChange for 5180 -> 5620
[ 3184.379841] ath: phy1: Set channel: 5180 MHz width: 2
[ 3184.379998] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3184.380666] ath: phy1: ah->misc_mode 0x10000004
[ 3184.384419] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3184.584140] ath: phy1: Set channel: 5640 MHz width: 0
[ 3184.584299] ath: phy1: Reset to 5640 MHz, HT40: 0 fastcc: 1
[ 3184.584319] ath: phy1: FastChannelChange for 5180 -> 5640
[ 3184.699800] ath: phy1: Set channel: 5180 MHz width: 2
[ 3184.699964] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3184.700639] ath: phy1: ah->misc_mode 0x10000004
[ 3184.704378] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3184.904131] ath: phy1: Set channel: 5660 MHz width: 0
[ 3184.904300] ath: phy1: Reset to 5660 MHz, HT40: 0 fastcc: 1
[ 3184.904319] ath: phy1: FastChannelChange for 5180 -> 5660
[ 3185.019770] ath: phy1: Set channel: 5180 MHz width: 2
[ 3185.019933] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3185.020607] ath: phy1: ah->misc_mode 0x10000004
[ 3185.024354] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3185.224106] ath: phy1: Set channel: 5680 MHz width: 0
[ 3185.224273] ath: phy1: Reset to 5680 MHz, HT40: 0 fastcc: 1
[ 3185.224293] ath: phy1: FastChannelChange for 5180 -> 5680
[ 3185.339758] ath: phy1: Set channel: 5180 MHz width: 2
[ 3185.339916] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3185.340588] ath: phy1: ah->misc_mode 0x10000004
[ 3185.344325] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3185.544091] ath: phy1: Set channel: 5700 MHz width: 0
[ 3185.544256] ath: phy1: Reset to 5700 MHz, HT40: 0 fastcc: 1
[ 3185.544275] ath: phy1: FastChannelChange for 5180 -> 5700
[ 3185.659753] ath: phy1: Set channel: 5180 MHz width: 2
[ 3185.659920] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
[ 3185.660625] ath: phy1: ah->misc_mode 0x10000004
[ 3185.664362] ath: phy1: Enabled BB Watchdog timeout (25 ms)
[ 3185.664457] ath: phy1: Set HW RX filter: 0x607
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 295 bytes
Desc: OpenPGP digital signature
Url : http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20140108/b9dcc95c/attachment-0001.pgp 

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08  9:18           ` Oleksij Rempel
@ 2014-01-08 10:58             ` Sujith Manoharan
  2014-01-08 11:18               ` Sujith Manoharan
  2014-01-08 11:32               ` Oleksij Rempel
  2014-01-08 16:18             ` Sujith Manoharan
  1 sibling, 2 replies; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-08 10:58 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> > Can you try this patch ?
> > 
> > diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
> > index 6d643ca..a638f3a 100644
> > --- a/drivers/net/wireless/ath/ath9k/recv.c
> > +++ b/drivers/net/wireless/ath/ath9k/recv.c
> > @@ -850,8 +850,9 @@ static int ath9k_process_rate(struct ath_common *common,
> >  	enum ieee80211_band band;
> >  	unsigned int i = 0;
> >  	struct ath_softc __maybe_unused *sc = common->priv;
> > +	struct ath_hw *ah = common->ah;
> >  
> > -	band = hw->conf.chandef.chan->band;
> > +	band = ah->curchan->chan->band;
> >  	sband = hw->wiphy->bands[band];
> >  
> >  	switch (hw->conf.chandef.width) {
> 
> seems to be fixed with this change. thank you :)

Thanks for testing, I'll post a more complete patch.

> [ 2689.964112] ath: phy1: Set channel: 5180 MHz width: 2
> [ 2689.964268] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
> [ 2689.964939] ath: phy1: ah->misc_mode 0x10000004
> [ 2689.968717] ath: phy1: Enabled BB Watchdog timeout (25 ms)
> [ 2690.168338] ath: phy1: Set channel: 2467 MHz width: 0
> [ 2690.168515] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
> [ 2690.168534] ath: phy1: FastChannelChange for 5180 -> 2467
> [ 2690.223270] ath: phy1: 
> [ 2690.223270] ==== BB update: BB status=0x13000609 ====
> [ 2690.223288] ath: phy1: ** BB state: wd=1 det=1 rdar=0 rOFDM=6 rCCK=0 tOFDM=0 tCCK=0 agc=3 src=1 **
> [ 2690.223298] ath: phy1: ** BB WD cntl: cntl1=0xffff010d cntl2=0x00000004 **
> [ 2690.223303] ath: phy1: ** BB mode: BB_gen_controls=0x01318bc0 **
> [ 2690.223307] ath: phy1: ** BB busy times: rx_clear=0%, rx_frame=0%, tx_frame=0% **
> [ 2690.223309] ath: phy1: ==== BB update: done ====
> [ 2690.223309] 
> [ 2690.223320] ath: phy1: BB_WATCHDOG: Skipping interrupts

I couldn't find much information about this signature. I'll ask our
baseband engineers.

What machine is this ? Did you replace the card with AR9462 ?

Can you see if this patch makes a difference ?

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 47c6285..b3e1d5e 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -2480,7 +2480,7 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah)
 	 * Fast channel change across bands is available
 	 * only for AR9462 and AR9565.
 	 */
-	if (AR_SREV_9462(ah) || AR_SREV_9565(ah))
+	if (AR_SREV_9565(ah))
 		pCap->hw_caps |= ATH9K_HW_CAP_FCC_BAND_SWITCH;
 
 	return 0;


Sujith

^ permalink raw reply related	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08 10:58             ` Sujith Manoharan
@ 2014-01-08 11:18               ` Sujith Manoharan
  2014-01-08 18:12                 ` Oleksij Rempel
  2014-01-08 11:32               ` Oleksij Rempel
  1 sibling, 1 reply; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-08 11:18 UTC (permalink / raw)
  To: ath9k-devel

Sujith Manoharan wrote:
> > seems to be fixed with this change. thank you :)
> 
> Thanks for testing, I'll post a more complete patch.

Just to confirm, can you test this patch on a clean tree
(without the earlier fix) and make sure that the debug message
is seen when the issue happens ?

Thanks !

diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
index 6d643ca..c1486d4 100644
--- a/drivers/net/wireless/ath/ath9k/recv.c
+++ b/drivers/net/wireless/ath/ath9k/recv.c
@@ -854,6 +854,13 @@ static int ath9k_process_rate(struct ath_common *common,
 	band = hw->conf.chandef.chan->band;
 	sband = hw->wiphy->bands[band];
 
+	if (hw->conf.chandef.chan->band != sc->sc_ah->curchan->chan->band) {
+		ath_dbg(common, ANY,
+			"Band/channel mismatch (%d, %d)\n",
+			hw->conf.chandef.chan->band,
+			sc->sc_ah->curchan->chan->band);
+	}
+
 	switch (hw->conf.chandef.width) {
 	case NL80211_CHAN_WIDTH_5:
 		rxs->flag |= RX_FLAG_5MHZ;


Sujith

^ permalink raw reply related	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08 10:58             ` Sujith Manoharan
  2014-01-08 11:18               ` Sujith Manoharan
@ 2014-01-08 11:32               ` Oleksij Rempel
  2014-01-08 16:19                 ` Sujith Manoharan
  1 sibling, 1 reply; 14+ messages in thread
From: Oleksij Rempel @ 2014-01-08 11:32 UTC (permalink / raw)
  To: ath9k-devel

Am 08.01.2014 11:58, schrieb Sujith Manoharan:
> Oleksij Rempel wrote:
>>> Can you try this patch ?
>>>
>>> diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
>>> index 6d643ca..a638f3a 100644
>>> --- a/drivers/net/wireless/ath/ath9k/recv.c
>>> +++ b/drivers/net/wireless/ath/ath9k/recv.c
>>> @@ -850,8 +850,9 @@ static int ath9k_process_rate(struct ath_common *common,
>>>  	enum ieee80211_band band;
>>>  	unsigned int i = 0;
>>>  	struct ath_softc __maybe_unused *sc = common->priv;
>>> +	struct ath_hw *ah = common->ah;
>>>  
>>> -	band = hw->conf.chandef.chan->band;
>>> +	band = ah->curchan->chan->band;
>>>  	sband = hw->wiphy->bands[band];
>>>  
>>>  	switch (hw->conf.chandef.width) {
>>
>> seems to be fixed with this change. thank you :)
> 
> Thanks for testing, I'll post a more complete patch.
> 
>> [ 2689.964112] ath: phy1: Set channel: 5180 MHz width: 2
>> [ 2689.964268] ath: phy1: Reset to 5180 MHz, HT40: 1 fastcc: 0
>> [ 2689.964939] ath: phy1: ah->misc_mode 0x10000004
>> [ 2689.968717] ath: phy1: Enabled BB Watchdog timeout (25 ms)
>> [ 2690.168338] ath: phy1: Set channel: 2467 MHz width: 0
>> [ 2690.168515] ath: phy1: Reset to 2467 MHz, HT40: 0 fastcc: 1
>> [ 2690.168534] ath: phy1: FastChannelChange for 5180 -> 2467
>> [ 2690.223270] ath: phy1: 
>> [ 2690.223270] ==== BB update: BB status=0x13000609 ====
>> [ 2690.223288] ath: phy1: ** BB state: wd=1 det=1 rdar=0 rOFDM=6 rCCK=0 tOFDM=0 tCCK=0 agc=3 src=1 **
>> [ 2690.223298] ath: phy1: ** BB WD cntl: cntl1=0xffff010d cntl2=0x00000004 **
>> [ 2690.223303] ath: phy1: ** BB mode: BB_gen_controls=0x01318bc0 **
>> [ 2690.223307] ath: phy1: ** BB busy times: rx_clear=0%, rx_frame=0%, tx_frame=0% **
>> [ 2690.223309] ath: phy1: ==== BB update: done ====
>> [ 2690.223309] 
>> [ 2690.223320] ath: phy1: BB_WATCHDOG: Skipping interrupts
> 
> I couldn't find much information about this signature. I'll ask our
> baseband engineers.
> 
> What machine is this ? Did you replace the card with AR9462 ?

Yes, i replaced the card. It is Asus Zenbook UX31A.

> 
> Can you see if this patch makes a difference ?
> 
> diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
> index 47c6285..b3e1d5e 100644
> --- a/drivers/net/wireless/ath/ath9k/hw.c
> +++ b/drivers/net/wireless/ath/ath9k/hw.c
> @@ -2480,7 +2480,7 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah)
>  	 * Fast channel change across bands is available
>  	 * only for AR9462 and AR9565.
>  	 */
> -	if (AR_SREV_9462(ah) || AR_SREV_9565(ah))
> +	if (AR_SREV_9565(ah))
>  		pCap->hw_caps |= ATH9K_HW_CAP_FCC_BAND_SWITCH;
>  
>  	return 0;

With this patch there is no more BB_WATCHDOG messages.

-- 
Regards,
Oleksij

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 295 bytes
Desc: OpenPGP digital signature
Url : http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20140108/fc78f167/attachment.pgp 

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08  9:18           ` Oleksij Rempel
  2014-01-08 10:58             ` Sujith Manoharan
@ 2014-01-08 16:18             ` Sujith Manoharan
  1 sibling, 0 replies; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-08 16:18 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> > Can you try this patch ?
> > 
> > diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
> > index 6d643ca..a638f3a 100644
> > --- a/drivers/net/wireless/ath/ath9k/recv.c
> > +++ b/drivers/net/wireless/ath/ath9k/recv.c
> > @@ -850,8 +850,9 @@ static int ath9k_process_rate(struct ath_common *common,
> >  	enum ieee80211_band band;
> >  	unsigned int i = 0;
> >  	struct ath_softc __maybe_unused *sc = common->priv;
> > +	struct ath_hw *ah = common->ah;
> >  
> > -	band = hw->conf.chandef.chan->band;
> > +	band = ah->curchan->chan->band;
> >  	sband = hw->wiphy->bands[band];
> >  
> >  	switch (hw->conf.chandef.width) {
> 
> seems to be fixed with this change. thank you :)

I've posted a patch to address this issue, can you please test it ?
https://patchwork.kernel.org/patch/3454781/

Sujith

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08 11:32               ` Oleksij Rempel
@ 2014-01-08 16:19                 ` Sujith Manoharan
  0 siblings, 0 replies; 14+ messages in thread
From: Sujith Manoharan @ 2014-01-08 16:19 UTC (permalink / raw)
  To: ath9k-devel

Oleksij Rempel wrote:
> > Can you see if this patch makes a difference ?
> > 
> > diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
> > index 47c6285..b3e1d5e 100644
> > --- a/drivers/net/wireless/ath/ath9k/hw.c
> > +++ b/drivers/net/wireless/ath/ath9k/hw.c
> > @@ -2480,7 +2480,7 @@ int ath9k_hw_fill_cap_info(struct ath_hw *ah)
> >  	 * Fast channel change across bands is available
> >  	 * only for AR9462 and AR9565.
> >  	 */
> > -	if (AR_SREV_9462(ah) || AR_SREV_9565(ah))
> > +	if (AR_SREV_9565(ah))
> >  		pCap->hw_caps |= ATH9K_HW_CAP_FCC_BAND_SWITCH;
> >  
> >  	return 0;
> 
> With this patch there is no more BB_WATCHDOG messages.

Patch: https://patchwork.kernel.org/patch/3454791/

Sujith

^ permalink raw reply	[flat|nested] 14+ messages in thread

* [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit
  2014-01-08 11:18               ` Sujith Manoharan
@ 2014-01-08 18:12                 ` Oleksij Rempel
  0 siblings, 0 replies; 14+ messages in thread
From: Oleksij Rempel @ 2014-01-08 18:12 UTC (permalink / raw)
  To: ath9k-devel

Am 08.01.2014 12:18, schrieb Sujith Manoharan:
> Sujith Manoharan wrote:
>>> seems to be fixed with this change. thank you :)
>>
>> Thanks for testing, I'll post a more complete patch.
> 
> Just to confirm, can you test this patch on a clean tree
> (without the earlier fix) and make sure that the debug message
> is seen when the issue happens ?
> 
> Thanks !
> 
> diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
> index 6d643ca..c1486d4 100644
> --- a/drivers/net/wireless/ath/ath9k/recv.c
> +++ b/drivers/net/wireless/ath/ath9k/recv.c
> @@ -854,6 +854,13 @@ static int ath9k_process_rate(struct ath_common *common,
>  	band = hw->conf.chandef.chan->band;
>  	sband = hw->wiphy->bands[band];
>  
> +	if (hw->conf.chandef.chan->band != sc->sc_ah->curchan->chan->band) {
> +		ath_dbg(common, ANY,
> +			"Band/channel mismatch (%d, %d)\n",
> +			hw->conf.chandef.chan->band,
> +			sc->sc_ah->curchan->chan->band);
> +	}
> +
>  	switch (hw->conf.chandef.width) {
>  	case NL80211_CHAN_WIDTH_5:
>  		rxs->flag |= RX_FLAG_5MHZ;


If you still need this test result:
[  222.222983] ath: phy0: Band/channel mismatch (0, 1)

-- 
Regards,
Oleksij

^ permalink raw reply	[flat|nested] 14+ messages in thread

end of thread, other threads:[~2014-01-08 18:12 UTC | newest]

Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-12-17 18:26 [ath9k-devel] ath: phy0: unsupported hw bitrate detected 0x1b using 1 Mbit Oleksij Rempel
2013-12-19  3:14 ` Sujith Manoharan
2013-12-19  7:33   ` Oleksij Rempel
2014-01-07 16:26     ` Sujith Manoharan
2014-01-07 20:50       ` Oleksij Rempel
2014-01-08  2:08         ` Sujith Manoharan
2014-01-08  9:18           ` Oleksij Rempel
2014-01-08 10:58             ` Sujith Manoharan
2014-01-08 11:18               ` Sujith Manoharan
2014-01-08 18:12                 ` Oleksij Rempel
2014-01-08 11:32               ` Oleksij Rempel
2014-01-08 16:19                 ` Sujith Manoharan
2014-01-08 16:18             ` Sujith Manoharan
2014-01-08  2:20         ` Sujith Manoharan

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.